RJA May 2012 Features-Glove

Page 1

Rubber Journal Asia Gloves added protection in case of an unnoticed glove breach during use. According to Eng Aik Hwee, Module Director, the technology uses an active ingredient, chlorhexidine gluconate (CHG), which reduces the microbial load on the active inside coated surface of the glove. About 4% of CHG, a water soluble and hygroscopic material, was coated in the inside surface. In terms of comfort, a very thin layer of anti-stick overcoat was applied over the antimicrobial coating to prevent the glove’s inside surface from adhering to the skin and to facilitate easy donning. A panel of five evaluators tried the glove and evaluated it according to dry and damp-hand donnability, double gloving, blocking (gloveto-glove inside and outside and glove-to-packaging), and wet look. All of the evaluators rated the antimicrobial glove as very easy to use and with no blocking and wetlook. For those allergic to protein, a test was conducted to find out if there were any traces of proteins on the antimicrobial glove. Results showed no detectable allergens and less than 50 water extractable proteins on the glove. It also indicated that the presence of antimicrobial agent has no correlation between the protein and allergen contents on the glove. Tensile properties of the antimicrobial glove met the aged and un-aged requirements of EN455 standard. The retention of force at break value was found to be above 90% for the glove. However, the un-aged force at break value of the antimicrobial glove was found to be slightly lower than that of the control glove, probably due to the additional processing steps, for instance, the antimicrobial agent applied to the glove. In vitro studies found that the glove killed more than 99% of an HCV surrogate virus and 99% of HIV-1 strain MN as early as 1 minute following exposure. The glove was also found to kill 99.7% to 99.9% of eight clinically relevant bacteria comprising gram-positive and negative and drug-resistant bacteria over 1 to 2 minutes exposure in similar studies. The kill-rate of the glove samples was performed by spreading 0.1 ml of inoculums with 5% organic soil load in the glove fingers for a specific period of time followed by neutralisation with Butterfield’s phosphate buffer solution with product stabilisers (BBP++). Serial dilutions were then made and plated for counting. The log reductions from the initial microbial recovery levels were determined by comparing recoveries from the antimicrobial gloves with those from control gloves without antimicrobial agent. Both real-time and accelerated aging studies confirmed that the glove has at least two years of shelf life in terms of meeting the EN-455-4 requirements. This was determined using the accelerated aging method. Within this period, the active ingredient remains stable and active. According to Ansell, the application of CHG to a powder-free NR surgical glove did not affect the functional performance of the glove. All the tests results show that the antimicrobial-coated glove can help further reduce the risk

In the last quarter of 2011, latex prices started to go up and are expected to remain stubbornly high. Latex costs for about 60% of a latex glove maker’s total production costs

of the surgeons and patients but not so much to ensure comfort during use. In terms of thickness, all gloves except for three types were within 200 micrometres. AnIR-B and ZN-IR-B were 250 micrometres, while CRL-A was about 175 micrometres. All gloves were thickest at the finger and thinnest at the cuff. All the surgical gloves evaluated met the ASTM standard for surgical gloves. However, when the extensometer was used, tensile strength of NR gloves was below the specification for all NR samples. It turned out that the reason for the unexpectedly low figures for the NR gloves was in the use of the extensometer. Hence, NR seems to be susceptible to small disturbances when under stress. The AnIR and CRL gloves suffer from easier tearing propagation than NR and ZN-IR gloves, but sustain higher or equivalent puncture energy, which may be related to tear initiation. Remarkably, the break pattern of the NR and ZN-IR was different than the pattern of the AnIR or the NYP types. The study showed that NR and ZN-IR types show an irregular break pattern, whereas the other types give a rather straight cut, perpendicular to the direction of the strain. The difference in break pattern for NR and ZN-IR can be an indication that their tearing behaviour is different than AnIR and CRL. The tearing propagation of the last two gloves may be faster. Overall, the study infers that all glove types studied offer comparable mechanical protection. Improving barrier effectiveness with CHG coating arrier effectiveness is vital in surgical gloves as it reduces the risk of contamination during contact with body fluids, mucous membranes or the damaged skin of patients. Mechanical stress, however, such as that occurring when gloves are repeatedly flexed through finger and hand manipulations, increase the chances of tears and punctures Taking protection a notch higher, a new antimicrobial technology has been developed by Ansell to provide

B

9 M AY 2 0 1 2

w w w. r u b b e r j o u r n a l a s i a . c o m


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.