ransmitter Operations

The door transmitter has four buttons (labeled LOCK, UNLOCK, AUX and HORN) control operation the system. When any the buttons pressed, a coded Ultra - high frequency (UHF) radio signal transmitted the receiver the vehicle.

The transmitter must within approximately meters (33 feet) the vehicle for the receiver detect the coded The Remote Keyless Entry system has fect the normal operation the power door

When the LOCK button pressed, the doors will lock and the lights will flash once indicating that the doors are locked. The dome light will for 5 seconds upon locking the door remote. For audible confirmation the door lock, press the LOCK button a second time and the horn will beep once confirm the doors are locked.

When the UNLOCK button pressed once, the drivers door will unlock and the lights will flash twice indicating that the door unlocked. The dome light will for seconds upon unlocking the door remote. Pushing the UNLOCK button a second time within 3 seconds will unlock both doors.

Note: AUT O - ARM feature selected, the keyless entry system will automatically - arm itself seconds after the doors are unlocked with remote transmitter . Automatic - arm will cancel any door opened before the seconds timer has

Press and hold the AUX button the transmitter for second turn perimeter trailer access lights "Of (if

Press and hold the HORN button the transmitter for 3 seconds. The horn will immediately sound and running lights will flash. During panic mode, the normal function this transmitter button will suspended. LOCK and UNLOCK buttons cannot used lock and unlock the doors. T o stop the alarm, press and hold the HORN button the transmitter again for 3 seconds. the button not pressed, the alarm will automatically stop after seconds.

Battery Replacement

Under normal use, the transmitter battery should last approximately two When battery replacement becomes necessary , use a Panasonic 3 type Replace the battery follows:

Open the transmitter inserting a dime between the two halves the transmitter case (near the key ring hole) and twisting.

Remove the battery Install a new battery with the positive (+) side down.

Battery , positive (+) side down

Align the transmitter case then snap the case together

Check the operation the transmitter .

The following checks may used diagnose any problems which may arise with Remote Keyless Entry system

Remember check all

Lower the windows, turn the ignition key the OFF position and close the doors.

Stand near the driver ’ s side door , aim the transmitter the vehicle and operate both functions the transmitter . Repeat for all transmitters, applicable.

• a single function one transmitter replace the transmitter

• all functions any the transmitters are inoperative, reprogram all transmitters and repeat the troubleshooting procedures. Refer the "Programming the T ransmitter" section.

• one transmitter cannot replace the battery the transmitter Refer the all functions all transmitters operate, stand approximately five feet from the vehicle (at several points around the vehicle), and check the operation all transmitters each point.

• one transmitter does not operate some point where another transmitter does operate, replace the battery the transmitter that does not operate.

• all transmitters operate approximately five feet from the the system operating properly and repairs should

Programming the T ransmitter: T urn the ignition switch the Access the keyless entry module, located behind the DPanel.

Push the Program switch the keyless entry module three The program LED the module will indicate you are now the T ransmitter Programming necessary , repeat Step 3 program the 2nd, 3rd and 4th transmitters.

Press any button one the transmitters until the horn responds with a chirp and the LED will flash once, confirm the first transmitter now programmed.

Note: more than four transmitters are the system will only retain the last four transmitters programmed.

T o exit Programming Mode, turn the ignition switch the OFF position, simply wait seconds. The LED will f confirm exit. https://www.truck-manuals.net/

Feature Programming:

T urn the ignition switch the position.

Access the keyless entry located behind the D -

Push the Program switch the keyless entry module six times. The horn will chirp six times, and the program LED the module will solid, indicate you are now the Feature Programming Mode.

Press and release the transmitter button corresponding the feature you want

Note: The horn chirps and LED pulses will indicate the new

Press the transmitter button again change the feature Keep pressing the transmitter button until the module advances your desired

AUX

External Light turns for 3 minutes External Light turns for 5 minutes

Three Chirps/LED Three pulses = External Light turns for minutes.

Four Chirps/LED Four pulses = External Light turns for

Five Chirps/LED Five pulses = External Light turns for minutes.

T o exit Programming turn the Ignition the "Of simply wait for The horn will respond with a short + long beep and the LED turns f confirm https://www.truck-manuals.net/