Linkbelt 210-240 X2 EXCAVATOR SERVICE MANUAL - PDF DOWNLOAD

Page 777

5-2 Lower Mechanism: Travel Drive Unit Safety Cautions Be sure to follow the instructions below:

Do not run the motor beyond the specified range. Doing so may cause damage to the machine.

Caution

Never touch the motor within 1 hour after the motor has stopped. The motor surface is very hot as it has been operating. Touching the motor can cause burn injuries.

Caution

Never suddenly remove the oil fill, oil discharge or oil check port of the reduction gear. Doing so may cause the plug to pop out, causing injury. Align the ports to the specified positions, and slowly loosen the plugs, starting from the oil fill port on the top, to release the air inside the reduction gear.

Reduction gear Top lubricating oil

Release air.

Oil fill port

Caution

Reduction gear lubricating oil Oil check port

Loosen the oil fill port about 2 turns to release air inside the reduction gear.

Reduction gear lubricating oil Bottom Oil drain port

Discharge oil. Discharge oil while slowly loosening the discharge port plug.

174


Turn static files into dynamic content formats.

Create a flipbook

Articles inside

2.5-way Solenoid Valve Operation Explanation

3min
pages 785-786

5.EPF (Engine Protection Feature

6min
pages 779-784

3.Upper Side Pilot Valve (remote control valve

5min
pages 787-791

4.Sensor Trouble Operation Table

1min
pages 777-778

1.Message Display List

2min
pages 766-767

3.Diagnostic Trouble Code (Monitor display

3min
pages 772-776

10.Engine Screen Information Screen Display Details

1min
page 765

9.Model Setting

2min
pages 763-764

8.Anti-Theft Protection Setting

2min
page 762

7.Option Flow Setting

3min
pages 760-761

6.Check the Monitor Switch (monitor switch check screen

3min
pages 758-759

5.CAL (troubleshooting support) Screen

5min
pages 755-757

2.DIAG (trouble diagnosis) Screen

1min
pages 743-744

3.HR (usage log) Screen List

8min
pages 745-751

2.Swing Motor

1min
page 742

Screen Display List 1.CHK (status display) Screen List

11min
pages 732-741

5.Beacon

4min
pages 728-730

4.Return Filter Restriction Detected

1min
page 727

1.Screen Shift

1min
page 731

1.Travel Motor

1min
page 723

2.Regulator

2min
pages 716-718

Options 1.Option Line Control

3min
pages 719-721

1) Breaker Q control

1min
pages 708-709

4.Second Option Circuit (hydraulic rotation fork

1min
pages 712-713

1.Breaker Circuit (single operation

3min
pages 704-705

2) 2nd crusher

1min
pages 710-711

1.Hydraulic Pump

2min
pages 714-715

2.Shuttle Circuit (hydraulic thumb

2min
pages 706-707

2.Heat Circuit (lever in neutral

2min
pages 700-701

Retightening torque table

18min
pages 664-689

2) When arm-out operation stopped

1min
pages 696-697

2.Travel Increased Horsepower Circuit Other Circuits

2min
pages 692-693

ISO type

1min
page 656

Increased Horsepower Circuits 1.Arm-In Increased Horsepower Circuit

1min
pages 690-691

1) Arm-out operation

1min
pages 694-695

Maintenance after first 250 hours for new machine / every 1000 hours from then ON 1.Swing Reduction Gear Oil Replacement

1min
page 660

7.Pressure Limiter

1min
page 636
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.
Linkbelt 210-240 X2 EXCAVATOR SERVICE MANUAL - PDF DOWNLOAD by www.heydownloads.com - Issuu