33 - Electrical System
57 - Electronic Diagnostic 90 - Fault Codes
Fault Codes 54000B 54000D
54000E 54020D
540B09 55020D
560A03 560A04 560A05 57060D 58020D
58060D
5A020D
5A0213
5B0000 5B0002 5B0004 5B0007 5B0008 33 - 288
Description Vehicle Speed above programmable Threshold #2. This is not a system failure/fault. J1939 Wheel-Based Vehicle Speed Signal from Source CCVS1, CCVS2 or CCVS3 is missing or not available = SNA (signal not available) Hall effect Vehicle Speed Sensor supply voltage out of range J1939 Cruise Control Enable Switch Signal from Source CCVS1, CCVS2 or CCVS3 missing or not available = SNA (signal not available) J1939 ETC7 Message is missing or not available J1939 Service Brake Switch Signal from Source CCVS1, CCVS2 or CCVS3 missing or not available = SNA (signal not available) Digital Output 4/02 Circuit shorted to Ubat Digital Output 4/02 Circuit shorted to GND Digital Output 4/02 Open Circuit (broken wire, terminal floating) J1939 Tachograph Output Shaft Speed Signal is missing or not available = SNA (signal not available) J1939 Cruise Control Coast Switch Signal from Source CCVS1, CCVS2 or CCVS3 missing or not available = SNA (signal not available) J1939 Tachograph Vehicle Speed Signal is missing or not available = SNA (signal not available) + J1939 TCO1 speed sensor selected J1939 Cruise Control Accelerator Switch Signal from Source CCVS1, CCVS2 or CCVS3 = SNA (signal not available) J1939 Cruise Control Accelerator Switch from Source CCVS1, CCVS2 or CCVS3 erractic = undefined value but not SNA Accelerator Pedal Circuit shorted to Ubat Accelerator Pedal out of adjustment (Learn error) Accelerator Pedal Circuit shorted to GND 2-Channel Accelerator Pedal Idle Not Recognized (idle area not evaluated) 2-Channel Accelerator Pedal Signal 1 missing
Fault Codes 5B000A 5B000D 5B000E 5B001F 60000D 61020C 61020D 61040D 6B0000 6B0002 6B0003 6B0004 6E1002 6F0001 6F0003 6F0004 6F0006 6F0012 6F1002 71020E
730C09 74020E 75020C 78000D
7F020D
9813/4150-6
Description Throttle pedal rationality check failed J1939 EEC2 message is missing or not available 2-Channel Accelerator Pedal Not Learned 2-Channel Accelerator Pedal Learned Range to Large Fuel Level Sensor Missing or Not Available CPC electronics are defect (EEPROM, CPU) The Engine ECU CPC4 SW is corrupt (CPC Software Diagnostics) J1939 Service Brake Switch Signal from EBC1 is missing or not available = SNA (signal not available) Air Filter Restriction High Air Filter Sensor plausibility error Air Filter diff.-pressure Sensor or switch shorted to Ubat Air Filter diff.-pressure Sensor or switch shorted to GND TSC1 Message Counter indicates lost Messages Coolant Level below safe operating level - (SEL Condition) Coolant Level Circuit shorted to Ubat Coolant Level sensor circuit failed (low) Coolant Level Sensor Circuit shorted to GND Coolant Level below operating level (pre-warning condition) TSC1 Message Checksum wrong PTCAN: MCM Sytem ID Not Received or Stopped Arriving (ECAN ID_596/7 not received or it has stopped arriving) Transmission Shift Console Datalink (LIN) XFLASH Static Fault Code Memory Page Read Write Failure (XFLASH Failure.) DDEC Data Xflash Write Error. Replace CPC. (XFLASH Failure.) J1939 Retarder Fluid Message is missing or not available (J1939 Cabin Message is missing or not available?) HDMS Fan is configured and the J1939 message was not received or has stopped arriving.
33 - 288