TMS800E OPERATOR’S MANUALOPERATING CONTROLS AND PROCEDURES

Section 3

Operating Controls And Procedures

The crane is equipped with two cabs, a carrier cab and a superstructure cab. The carrier cab (see Figure 3-1) contains all controls and indicators necessary for crane traveling and parking. The superstructure cab (see Figure 3-3) contains all controls and indicators necessary to perform all craning operations. Both cabs utilize international symbols and English text to label the various controls. For detailed information on either cab, refer to either CARRIER CAB or SUPERSTRUCTURE CAB in this Section.

NOTE: The following paragraphs describe all the available (standard and optional) controls and indicators located in the cab. Some machines may not be equipped with the optional controls shown. The numbers in () represent the index number from (Figures 3-1 through 3-3).

NOTE: All rocker switches contain one or two LED’s in the switch for illumination.

NOTE: All indicators on the top row of the consoles will illuminate solid, all at the same time for approximately two seconds as a diagnostic test when the ignition switch is positioned to on. If any indicator fails to illuminate, replace it immediately.

Carrier Cab

Engine Controls and Indicators Gauge Cluster

The gauge cluster (5) is located in the center of the front console assembly and contains a voltmeter, oil pressure gauge, water temperature gauge, and a fuel quantity gauge.

Voltmeter

The voltmeter (VOLTS) is located on the lower right of the gauge cluster. With the ignition switch in the run (between vertical and far right) position and before starting the engine, the voltmeter indicates the condition of the batteries. With the engine running, the voltmeter indicates output voltage of the alternator. The voltmeter scale is from 10 to 16 volts.

Engine Oil Pressure Gauge

The engine oil pressure (OIL) gauge is located on the upper right of the gauge cluster. The gauge indicates the engine oil pressure on a scale calibrated from zero (0) to 80 psi. It receives a signal from the crane’s electronic operating system which receives the signal from the engine ECM via J1939.

Water Temperature Gauge

The engine coolant temperature (TEMP) gauge is located on the lower left of the gauge cluster. The gauge indicates the engine coolant temperature on a scale calibrated from 100 to 240° F. The gauge receives a signal from the crane’s electronic operating system which receives the signal from the engine ECM via J1939.

Fuel Quantity Gauge

The fuel quantity (FUEL) gauge is located on the upper left of the gauge cluster. The gauge indicates the quantity of fuel in the tank and has a scale calibrated from empty (E) to full (F). The fuel quantity gauge receives a signal from the crane’s electronic operating system which monitors a sending unit in the fuel tank.

Engine Stop/Module Off Line Indicator

The engine stop/module off line indicator (23) is located on the top left side of the front console. The top portion of the switch is the stop indicator. It illuminates red when energized by a signal from the engine ECM that signifies a serious engine problem that requires the vehicle and the engine to be stopped as soon as safely possible. In addition, a warning buzzer will also sound.

The bottom portion is the module off line indicator. This indicator will come on solid and a buzzer will sound whenever communication with one of the crane’s electronics modules is lost. The vehicle should be stopped as soon as safely possible. The crane must be restored to proper condition before operating again.

Engine Warning/Electrical System Diagnostic Indicator

The engine warning/electrical system diagnostic indicator (24) is located at the top left side of the front console. The top portion is the warning indicator. It illuminates amber when energized by a signal from the engine ECM that signals the operator of an engine problem which must be corrected.

The bottom portion of the switch is the electrical system diagnostic indicator. There are three conditions for this indicator as follows: a. On solid with buzzer sounding - There is an interruption of communication over the main canbus control line between the crane’s electronic control modules. Proper crane operating condition shall be restored as quickly as possible. b. Flashing with buzzer sounding - An undesirable condition with the crane’s joysticks has been detected. Proper crane operating condition shall be restored before performing any hydraulic function. c. Flashing without buzzer - An undesirable component or electrical system condition has occurred.

Engine Coolant Temperature Indicator

The engine coolant temperature indicator (25) is located at the top left side of the front console. It illuminates amber to indicate high engine coolant temperature.

Tachometer

The tachometer (2) is located on the right side of the front console. The tachometer is calibrated in RPM x 100 with a range of zero (0) to 35. It receives a signal from the crane’s electronic operating system which receives the signal from the engine ECM via J1939.

Engine Brake On/Off Switch

The engine brake on/off switch is located on the left center side of the front console. The two position (on/off) switch (22) energizes the engine brake. When the top of the switch is pushed, the switch is in the on position.

Engine Brake High/Low Switch

The two position engine brake high/low switch (20) controls the amount of engine braking.

When the top of the switch is pushed, the switch is in the high position.

Ignition Switch

The ignition switch (14) is located on the right side of the front console. The switch is key operated with four positions: accessory (left position), off (vertical position), run (position between vertical and right), and start (right position).

With ignition switches in both cabs in the off position, all electrical power is off except for the headlights, marker lights, gauge lights, turn and stop light, carrier and superstructure cab dome lights, carrier and superstructure cab 12V accessory outlets, superstructure cab work lights, and superstructure horn.

The accessory position energizes all electrical components except the engine ECM. The run position is the same as accessory except the engine ECM is energized. The start position energizes the starter relay which in turn energizes the cranking motor solenoid and cranks the engine for starting. The switch will return to run when the switch is released after the engine is started. Turn the switch to off to shut down the engine.

Throttle Pedal

The THROTTLE pedal (38) is the right most pedal on the cab floor. It is used to control engine speed. The foot pedal modulates engine speed proportionately to the foot pressure applied. The pedal is angled for increased operator comfort. The foot pedal is monitored by the crane’s electronic operating system which sends the information to the engine ECM via J1939.

Engine Idle Switch

This switch (35) is a two position (+/-) momentary rocker switch on the left side of the front console. It provides idlecontrol inputs that increase and decrease the engine idle.

Travel Controls and Indicators

Dual Air Pressure Gauge

The dual air pressure gauge (1) is located on the right side of the front console. The gauge is a direct reading pressure gauge with two indicating pointers, red for the primary system and green for the secondary system. The gauge has a dual scale calibrated from 100 to 1000 kPa and 0 to 150psi. The gauge is connected to each air system separately through tubing.

Low Air Pressure/Tire Inflation On Indicator

The low air pressure/tire inflation on indicator (27) is located on the top left side of the front console. The indicator illuminates red when t he pressure in either or both air systems is below 517 kPa (75 psi). The indicator is controlled by two pressure switches electrically connected in parallel. To determine which system pressure is low, observe the dual air pressure gauge. In addition to illuminating the indicator, a warning buzzer will sound.

The bottom of the indicator illuminates amber when the pressure switch in the tire inflation system is activated. In addition to illuminating the indicator, a warning buzzer will sound.

Speedometer

The speedometer (4) is located in the center of the front console above the steering wheel. The speedometer indicates road speed in both km/h (kilometers per hour) and mph (miles per hour).

Odometer

There is an odometer (16) located at the bottom of the speedometer and shows total distance traveled.

Parking Brake Control

NOTE: The park brake must be set before the outrigger controls will operate.

The parking brake control (12) is located on the right side of the front console. The control is a push-pull type air valve used to apply and release the parking brakes on all four rear wheels.

Park Brake Engaged Indicator

The park brake engaged indicator (29) is located at the top of the front console. The indicator illuminates red when the