Laser Tools COIL SPRING COMPRESSOR FOR MERCEDES-BENZ • Telescopic spring compressor • Tool Extends from 70 to 393 mm. Max load 14,900 Kgf • It is now possible to remove and replace the coil springs on the wishbone without dismantling the axle saving valuable time and money • Also suitable for use on multi-link independent suspensions • Supplied with two sizes of pressure plate
WHEEL HUB HOLDING TOOL
RACK END REMOVER 25-55MM
• • • • •
• • • • •
Designed for use on vehicles with 4 stud, 5 stud, 6 stud and 8 stud patterns flanges and hubs where access permits Applications include: Wheel Hubs, Drive flanges, Gear box output drive flanges, Differential input and output flanges Non-slip plastic dipped handle Can also be used to hold rear differential yokes on solid axle vehicles during bearing service Can also be used with a 1/2" drive power bar or Torque wrench. Remember to make allowance for the addtional length of the tool
4870
7090
ONLY
ONLY
£179.95 COIL SPRING COMPRESSOR MACPHERSON STRUTS • Specifically designed for Macpherson struts fitted to most vehicles • Complete with robust shaft which extends up to 300mm • 3 size of pressure plates from 80mm<115mm, 110<150mm & 140<195mm • The anti-slip locking mechanism ensures the struts are compressed safely • An adaptor for Conical springs fitted to some Alfa Romeo, Chrysler, Nissan, Seat and Volkswagen is included
NEW
£19.95 MACPHERSON CLAMP SEPARATOR SET • • • • •
One tool covers many applications No need to remove track rod end - slide tool over and onto knuckle Fits knuckles with hex drive, two flats or round ends Ideal for confined spaces For steering rack knuckles with a diameter of 25-55mm
Separator bits = 7.5 to 9.0mm, 5.2 to 6.9mm, 6.6 to 7.9mm, 4.3 to 6.0mm, 12.7 to 16.7mm Includes 3/8” square drive handle with bit holder Fast and efficient, holds the clamp open for removal and fitting of the Macpherson strut and hubs Applications include: Citroën, Peugeot, Ford, VAG, Audi where Macpherson struts are clamped into the hub Kit includes a 17mm combination ratchet wrench for use where access does not allow the use of the socket and drive handle combination
5926
ONLY
£44.95 HANDS FREE SUSPENSION ARM LEVER • S pecifically designed to pull and hold down the lower suspension arms to allow separation of the hub from the lower arms • Also assists in the separation of lower ball joint or suspension struts from the hub • Makes the job easier and safer with hands free operation • Suitable for most cars and light commercial vehicles • Made in Italy - Patented No 1479482
4871
ONLY
£299.95 INTERNAL COIL SPRING COMPRESSOR • • • • •
For wishbone, independent and multi-link suspension systems Restricted access: Suitable for springs where the lower wish bone access hole is 30mm or bigger (tool shaft size 29mm). Maximum load 3800kgf (37,240N) Suitable for use with air impact tools when using the torque limiting bar provided Also complete with two forged steel pressure plates 150mm & 130mm, Manufactured from steel and Chrome Molybdenum Applications: Chrysler, Chevrolet, Citroën, Ford, Honda, Hyundai, Kia, Mazda, Mitsubishi, Peugeot, Renault, Skoda, Suzuki, Toyota, Volvo, Volkswagen Including: BMW 3 series (1996-2013 Mercedes-Benz W202/W204 (1997-2013). Ideal for Ford Focus rear springs as tested in our Tech Centre
6798
ONLY
£44.95 BEARING/BUSH REMOVAL/INSERTION KIT • • • • •
For use on bushes, bearings seals 20 sizes of adaptors ranging from 34-72mm (double sized) 4 threaded bars. Spares: Part No: 2473 M10 2474 M12 2475 M14 2485 M16 Universal use Adequate and appropriate lubricants to be used on threaded force screws and thrust bearing (Laser Tools Recommends Molybdenum Disulphide Grease (black drive shaft grease)
5931
5178
ONLY
ONLY
£249.95
£299.95
SHOCK ABSORBER TOOL KIT - 14PC
INNER TIE ROD TOOL - MULTI PURPOSE
• • • • •
• • • • •
Specifically designed for repairing and replacing shock absorbers Manufactured from Chrome Vanadium Contents: 7 x Go Thru’ deep sockets: 16/17/18/19/21/22/24mm, 3 x 1/2”D Hex bits: 6mm/7mm/8mm, 1 x sliding T-bar 1/2”D, 2 x slot bit sockets 5 x 8mm, 6 x 8mm x 1/2”D Also includes 1 x 21mm Hex Go Thru’ ratchet Packed in EVA foam in a blow mould case
Universal use Capacity 33-42mm Use to replace the inner tie rod end without replacing the rack and pinion Robust tool Main body: (H) 32.70mm, (W) 58mm, (L) 70.21mm, Overall height 57.41mm
6936
ONLY
£199.95 CV JOINT PULLER • • • •
A robust tool for front wheel drive cars Removes CV joints without removing drive shaft Essential service tool Adjustable
4719
ONLY
£59.95 CV BOOT CLAMP PLIERS • • • •
Heavy duty Can be used by hand or with the assistance of a power bar if required Also suitable for installation of certain clamps on fuel filters, water pumps and other cooling systems PVC dipped handles for comfort
6182
3829
4136
ONLY
ONLY
ONLY
£89.95
8
£39.95
£24.95 autoparts