Miniguide_ecodur_sept26_eng_issuu by englund-gruppen-flooring

ECODUR® ECODUR

MINI GUIDE 2026.09

CONTENTS Primers and moisture barriers............................................................ 3 Self levelling compounds................................................................... 13 Repair- and patching materials ....................................................... 25 Adhesives ................................................................................................ 33 Other.......................................................................................................... 47 Guides ....................................................................................................... 57 Systems .................................................................................................... 64 Pumping of self levelling compounds .......................................... 89

Please observe! The information in this brochure is based on our many years of experience and extensive surveys. However, since the conditions on the building site are beyond our control, we cannot be held responsible for the end result achieved. If in doubt, a trial is recommended before the work begins. The most recently published product information and general information about the floor laying process can be found on www.englund-gruppen.se. Industry regulations, national standards and norms, as well as information from the relevant flooring manufacturer must also be taken into account.

PRIMERS AND MOISTURE BARRIERS

ECODUR® P 10 Allround primer Fast drying Multi-purpose Solvent-free

A film forming, solvent-free adhesion primer with very low emissions for use on substrates such as concrete, lightweight concrete, screeds, floor planks, chipboards, cement- and gypsum based plasters. For interior walls and floors.

Pretreatment The substrate must be load-bearing, durable, completely dry, clean, free from water-soluble adhesive residues and other substances that may impair the adhesion.

Application Ensure that the primer is at room temperature. Shake and pour the contents of the can into a clean bucket. Dilute with clean, cold water using the mixing ratio specified in the table. Apply the primer evenly across the surface using a roller or brush. Avoid puddle formation. Allow the primer to dry before further work. After use, immediately clean your tools with water. Optimum application temperature is 1025°C. High temperature and low humidity

shortens the drying time, whilst the reverse is true in low temperature and high humidity environments.

Moisture The product has normal resistance to moisture and is not suitable for use on all floor types. Therefore, it is of outmost importance that the residual moisture content of the concrete subfloor is measured, ideally by an certified moisture controller, and documented to ensure that the covering is not applied to a substrate with too high moisture content. When laying PVC and diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open linoleum and textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Please observe! • Subsequent levelling work must start no later than 72 hours after ECODUR® P 10 has been applied. • Never use ECODUR® P 10 as an adhesion primer directly under parquet and hardwood floor adhesive.

ECODUR® P 10 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

5 kg canister

Colour:

Light blue

Consumption:

Approx. 40-100 g/m2 depending on the absorbency of the substrate.

Mixing ratio:

Concrete (1:5) Lightweight concrete (1:3) Cement-based screeds (1:3) Calcium sulphate-based screeds (1:1) Gypsum based plasters (1:1) Cement mortar, lime cement plasters (1:3) Gypsum boards (1:1) Floor planks (1:1)

Working temperature:

Minimum floor temperature 10°C

Drying time:

For adhesion and reduced absorption approx. 0.5 hours As moisture protection during application phase 24 hours*

Underfloor heating:

Suitable

Resistance to castor wheels:

Can be used

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C och 65 % RH

ECODUR® P 11 Primer for non-absorbent substrates Fibre reinforced Extremely good adhesion Solvent-free

Ready-mixed, extremely quick-drying, solvent-free adhesion primer with very low emissions for use on most smooth, non-absorbent substrates such as ceramic tiles, epoxy resins, terrazzo, and chipboards. For use in dry, indoor environments. For interior walls and floors.

Pretreatment The substrate must be load-bearing, durable, completely dry, clean, free from water-soluble adhesive residues and other substances that may impair the adhesion.

Application Ensure that the primer is at room temperature and shake the bucket thoroughly before opening. Apply a thin layer of the primer across the entire surface using a roller. Avoid puddle formation. Allow the primer to dry before further work. After use, immediately clean your tools with water. Optimum application temperature is 1025°C. High temperature and low humidity

shortens the drying time, whilst the reverse is true in low temperature and high humidity environments.

Please observe! • If you are in any doubt about adhesion, do a small test on a limited area. • Subsequent levelling work must start no later than 72 hours after ECODUR® P 11 has been applied. • Never use ECODUR® P 11 as an adhesion primer directly under parquet and hardwood floor adhesive.

ECODUR® P 11 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

5 kg bucket

Colour:

Blue

Consumption:

Approx. 100 g/m2

Mixing ratio:

Ready-mixed and not to be diluted

Working temperature:

Minimum floor temperature 10°C

Drying time:

For adhesion and reduced absorption, approx. 0.5-2 hours*

Underfloor heating:

Can be used

Resistance to castor wheels:

Suitable

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C och 65 % RH 7

ECODUR® P 12 Primer for absorbent substrates Extremely rapid drying Good penetration capacity Solvent-free Ready-mixed, extremely rapid drying, solvent-free adhesion primer with very low emissions for use on absorbent substrates such as concrete, lightweight concrete, rapid cement mortars, gypsum based self levelling compounds, and gypsum boards. For interior and exterior use.

Pretreatment The substrate must be load-bearing, durable, completely dry, clean, free from water-soluble adhesive residues and other substances that may impair the adhesion.

Application Ensure that the primer is at room temperature. Shake and pour the contents of the can into a clean bucket. Apply the primer evenly in a generous layer across the surface using a roller or brush. Avoid puddle formation. Allow the primer to dry before further work. After use, immediately clean your tools with water. Optimum application temperature is 1025°C. High temperature and low humidity shortens the drying time, whilst the reverse

is true in low temperature and high humidity environments.

Moisture The product is highly moisture resistant, making it suitable for use on most absorbent substrates. However, it is of outmost importance that if the above used products such as levelling compounds, adhesives, and coverings are not moisture resistant, that the residual moisture content of the concrete subfloor is measured, ideally by an certified moisture controller, and documented to ensure that the covering is not applied to a substrate with too high moisture content. When laying PVC and diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open linoleum and textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Please observe! • Subsequent levelling work must start no later than 72 hours after ECODUR® P 12 has been applied. • Never use ECODUR® P 12 as an adhesion primer directly under parquet and hardwood floor adhesive. • Please note that the material consumption must not be less than 100 g m2 as this can result in a deteriorated surface in the form of pinholes and orange skin in the subsequent self levelling compound.

ECODUR® P 12 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

5 kg canister

Colour:

Purple

Consumption:

Approx. 100-150 g/m2 depending on the absorbency of the substrate.

Mixing ratio:

Ready-mixed and not to be diluted

Working temperature:

Minimum floor temperature 10°C

Drying time:

For adhesion and reduced absorption, approx. 10 minutes As moisture protection during the application phase, approx. 1 hour*

Underfloor heating:

Suitable

Resistance to castor wheels:

Suitable

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C och 65 % RH 9

ECODUR® P 19 Moisture barrier primer Water and solvent-free Neutral smell Chemical-resistant A film forming 1-K PUR primer for use on concrete, screeds, self levelling compounds, chipboards, etc. Can be used as an adhesion primer before adhere parquet and hardwood floors with ECODUR® S 90 New - or as a moisture barrier against residual moisture in concrete floors with maximum 98% RH. For interior and exterior use.

Pretreatment The substrate must be load-bearing, durable, surface-dry, clean, free from adhesive residues and other substances that may impair the adhesion. Sealed and glossy surfaces must always be sanded using a grinding machine and fine sandpaper.

Application The product can be applied in a single layer as an adhesion primer prior to adhere parquet and hardwood floors - or in two or three layers as a moisture barrier before levelling and adhering of parquet and hardwood floors. The primer must be at room temperature. Shake the packaging well, pour the content 10

of the can into a clean bucket, and apply the product evenly and crosswise between the layers using a short bristle, lint-free roller. Material use approx. 100–350 g/m2, depending on the number of layers applied. Check material use every now and again. Avoid puddle formation. Drying time between layers is approx. 40-50 minutes, and approximately 2 hours after the last layer has dried, parquet and hardwood floors can be adhered using ECODUR® S 90 New. Used tools such as roller sleeves, brushes, etc. must be discarded and hardened material can only be removed mechanically. Ideal laying temperature is 15-25°C. ECODUR® P 19 can also be used as a moisture barrier under self levelling compounds and, in such cases, must be primed using ECODUR® P 11 adhesive primer, alternatively directly after application of the last layer sprinkled with washed sea sand in fraction 0.4-0.8 mm. When the surface is completely dry, excess sand is vacuumed up.

Moisture

Consumption

The product is suitable to use as a barrier against residual moisture, provided that residual moisture content does not exceed 98 % RH. Always contact us for consultation if the substrate is exposed to rising ground moisture.

In one layer as an adhesion primer

approx. 100-150 g/m2

In two layers as a moisture barrier on cement-based substrates with a residual moisture of up to 95 %

approx. 200–250 g/m2

Please observe! • For professional use only! As of August 24, 2023, appropriate training is required before industrial or professional use. • Drying time between layers may not exceed 72 hours. • ECODUR® P 19 must not be applied too thickly as this will make the product brittle and increse the curing time dramatically.

In three layers as approx. a moisture barrier 300–350 g/m2 on cement-based substrates with a residual moisture of up to 98% RH Always contact us for further consultation when applying on substrates with underfloor heating.

ECODUR® P 19 has been assessed by

Byggvarubedömningen and is registered in BASTA.

Pack size:

5.5 kg canister

Colour:

Blue

Mixing ratio:

Ready-mixed and not to be diluted

Working temperature:

Minimum floor temperature 15°C

Drying time:

Between layers approx. 40- 50 minutes. Before adhere parquet and of hardwood floors approx. 2 h. Before levelling approx. 12 h.

Underfloor heating:

Suitable

Resistance to castor wheels:

Suitable

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C och 65 % RH 11

SELF LEVELLING COMPOUNDS

ECODUR® E 31 New Cross-over self levelling compound 0-20 mm thickness Benefits of both gypsum and cement Very low shrinkage A fast-curing crossover levelling compound with very low shrinkage that combines the benefits of gypsum and cement. For use on concrete, lightweight concrete, cementbased screed, prefabricated concrete elements, gypsum based substrates, glued and screwed chipboards, even if these are porous or have residues of asphalt and tar glue, prior to laying of PVC, linoleum or textile floor coverings, as well as fully adhered parquet and hardwood floors. For application on other types of substrate, we always recommend consulting us for technical support. Suitable for use in residential areas, offices, and light industrial premises. For interior floors.

Subfloor preparation The substrate must be load-bearing, durable, completely dry, clean, be free from adhesive residues and other substances that may affect adhesion. Prior to levelling always use a suitable ECODUR® adhesion primer.

Mixing Pour clean, cold water into a mixing bucket, add the powder, and mix mechanically until the compound is lumpfree and homogeneous. In layers with a thickness in excess 14

of 10 mm, 25 kg of ECODUR® E 31 New can be supplemented with 12.5 kg of washed quartz sand with a grain size of 0.8-1.2 mm.

Application Only mix as much material that can be applied within the working time. ECODUR® E 31 New can be applied by hand or be pumped. Newly applied material must be protected against frost, drafts, and sunlight. Excessively fast drying may cause cracking, deformation, or impaired surface durability.

Moisture and drying This product is low alkali, has fast strength development, and binds the greater part of its mixing water eventually, meaning that the floor coverings can be laid quickly. However, it is vital that the amount of residual moisture in the concrete subfloor is measured and documented so that the levelling compound and subsequent covering is not installed on a substrate that is too damp. When laying PVC and diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open linoleum and textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture

barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Please observe! • The product can be used as a migration barrier when applied in minimum 5 mm. • Always use a measuring bucket to ensure that the right amount of water is added. • Priming is required before leveling with cement-based products. • Application of more than one layer: If an additional layer is to be applied on the same day, when the underlying surface is still dark, the surface must be scraped, vacu-

C 40

umed, and the second layer worked into the surface. The second layer must always be thinner than the first. Where an additional layer is to be applied once the underlying layer has dried and lightened, the surface must be sanded, vaccuumed, and primed using ECODUR® P 12, primer, which must be allowed to dry before the second layer is applied. The second layer must always be thinner than the first. • Always use an expansion strip along walls where the thickness of layers exceeds 5 mm. • The product is suitable for use under fully adhered parquet and hardwood floors, contact us for a consultation. ECODUR® E 31 New has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

25 kg bag

Colour:

Light grey

Layer thicknesses:

0-20 mm Contact us for advice about thicker layers.

Consumption:

Approx. 1.6 kg/m2 and mm of layer thickness.

Water quantity:

Approx. 5.5 l/25 kg powder

Working temperature:

Minimum floor temperature 15°C

Working time:

Approx. 20-30 minutes*

Ready for foot traffic:

After approx. 2 hours*

Ready for covering:

With PVC, linoleum, and textile after: 0-6 mm - 6 h, 7-12 mm - 12 h, 13-20 mm - 24 h. The product may remain open for a maximum of 3 days before covering.

Reinforcement:

The product can be reinforced with a fibre mesh

Underfloor heating:

Suitable

Resistance to castor wheels: Yes, in layers over 3 mm Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment.

* at 20°C och 65 % RH 15

ECODUR® E 33 New Cement-based self levelling compound Very smooth surface Exceptional flow capacity Ready for covering after 16 hours A cement-based self levelling compound for use on concrete, cement-based screeds, prefabricated concrete elements, etc. prior to laying of PVC, linoleum, textile floor coverings, ceramic tiles, or fully adhered parquet and hardwood floors. For application on other types of substrate, we always recommend consulting us for technical support. Suitable for use in residential areas, offices, and light industrial premises. For interior floors.

Mixing Pour clean, cold water into a mixing bucket, add the powder, and mix mechanically until the compound is lumpfree and homogeneous. In layers with a thickness in excess of 10 mm, 25 kg of ECODUR® E 33 New can be supplemented with 12.5 kg of washed quartz sand with a grain size of 0.8-1.2 mm. 16

Application Only mix as much material that can be applied within the working time. ECODUR® E 33 New can be applied by hand or be pumped. Newly applied material must be protected against frost, drafts, and sunlight. Excessively fast drying may cause cracking, deformation, or impaired surface durability.

The moisture content in chipboards should be between 8-12 %.

Please observe! • Always use a measuring bucket to ensure that the right amount of water is added. • Application of more than one layer: If an additional layer is to be applied on the same day, when the underlying surface is still dark, the surface must be scraped, vaccuumed, and the second layer worked into the surface. The second layer must always be thinner than the first.

once the underlying layer has dried and lightened, the surface must be sanded, vaccuumed, and primed using ECODUR® P 12, primer, which must be allowed to dry before the second layer is applied. The second layer must always be thinner than the first. • Always use an expansion strip along walls where the thickness of layers exceeds 5 mm. • The product is suitable for use under fully adhered parquet and hardwood floors, contact us for a consultation.

Where an additional layer is to be applied

ECODUR® E 33 New has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

25 kg bag

Colour:

Grey

Layer thicknesses:

0-30 mm Contact us for advice about thicker layers.

Consumption:

Approx. 1.5 kg/m2 and mm of layer thickness.

Water quantity:

Approx. 6.5 l/25 kg powder

Working temperature:

Minimum floor temperature 15°C

Working time:

Approx. 20-30 minutes*1

Ready for foot traffic:

After approx. 2 hours*1

Ready for covering:

After approx. 16 hours*1 *2 The product may remain open for a maximum of 7 days before covering.

Reinforcement:

The product can be reinforced with a fibre mesh

Underfloor heating:

Suitable

Resistance to castor wheels: Yes, in layers over 3 mm Storage: *1 at 20°C and 65 % RH

At least 9 months from the date of manufacture if stored in unopened packaging in a dry and cool environment. *2 with PVC, linoleum, textile floor coverings, and ceramic tiles 17

ECODUR® E 34 Cement-based self levelling compound 0-10 mm thickness Extremely good flow properties Low tension Cement-based self levelling compound for use on concrete, lightweight concrete, cement-based screed, and prefabricated concrete elements prior to laying of PVC, linoleum, or textile floor coverings. For application on other types of substrate, we always recommend consulting us for technical support. Suitable for use in residential areas, offices, and light industrial premises. For interior floors.

Mixing Pour clean, cold water into a mixing bucket, add the powder, and mix mechanically until the compound is lumpfree and homogeneous.

Application Only mix as much material that can be applied within the working time. ECODUR® E 34 can be applied by hand or be pumped. Newly applied material must be protected against frost, drafts, and sunlight. Excessively fast drying may cause cracking, deformation, or impaired surface durability.

The moisture content in chipboards should be between 8-12 %.

Where an additional layer is to be applied once the underlying layer has dried and lightened, the surface must be sanded, vaccuumed, and primed using ECODUR® P 12, primer, which must be allowed to dry before the second layer is applied. The second layer must always be thinner than the first. • If parquet is to be fully adhered on the substrate, we suggest using ECODUR® E 31 New or ECODUR® E 33 New, supplemented by advice from our laying specialists. • Always use an expansion strip along walls where the thickness of layers exceeds 5 mm.

ECODUR® E 34 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

25 kg bag

Colour:

Grey

Layer thicknesses:

0-10 mm Contact us for advice about thicker layers.

Consumption:

Approx. 1.5 kg/m2 and mm of layer thickness.

Water quantity:

Approx. 6.0 l/25 kg powder

Working temperature:

Minimum floor temperature 15°C

Working time:

Approx. 30 minutes*1

Ready for foot traffic:

After approx. 3 hours*1

Ready for covering:

After approx. 24- 36 hours*1 *2 The product may remain open for a maximum of 7 days before covering.

Reinforcement:

The product can be reinforced with a fibre mesh

Underfloor heating:

Suitable

Resistance to castor wheels:

Yes, in layers over 3 mm

Storage:

At least 6 months from the date of manufacture if stored in unopened packaging in a dry and cool environment.

*1 at 20°C and 65 % RH

*2 with PVC, linoleum, textile floor coverings, and ceramic coverings 19

ECODUR® E 36 Fibre-reinforced levelling compound Low tension Suitable for levelling of slopes Ready for covering after 24 hours A fibre-reinforced cement-based self levelling compound for use on concrete, lightweight concrete, cement-based screed, terrazzo, prefabricated concrete elements, as well as permanently installed chipboards prior to laying of PVC, linoleum, textile floor coverings, or ceramic tiles. For application on other types of substrate, we always recommend consulting us for technical support. Suitable for use in residential areas, offices, and light industrial premises. Suitable for outdoor and permanently or periodically damp environments. Protect with suitable waterproofing or moisture-resistant covering.

Mixing Pour clean, cold water into a mixing bucket, add the powder, and mix mechanically until the compound is lumpfree and homogeneous. In layers with a thickness of more than 25 mm, 20 kg of ECODUR® E 36 can be 20

supplemented with 10 kg of washed quartz sand with a grain size of 0.8-1.2 mm.

Application Only mix as much material that can be applied within the working time. ECODUR® E 36 can be applied by hand or be pumped. Newly applied material must be protected against frost, drafts, and sunlight. Excessively fast drying may cause cracking, deformation, or impaired surface durability.

Moisture and drying This product is low alkali, has fast strength development, and binds the greater part of its mixing water eventually, meaning that the floor coverings can be laid quickly. However, it is vital that the amount of residual moisture in the concrete subfloor is measured and documented so that the levelling compound and subsequent covering is not installed on a subfloor that is too damp. When laying PVC and diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open linoleum and textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation.

The moisture content in chipboards should be between 8-12 %.

Please observe! • Chipboards must be at least 22 mm thick, glued and screwed to the beams with a max. c/c distance of 600 mm. The floor surface must be primed with ECODUR® P 11. Before levelling, the floor must be reinforced with steel or fibreglass PZG reinforcement. Use expansion strips along all walls. • Always use a measuring bucket to ensure that the right amount of water is added. • Application of more than one layer: If an additional layer is to be applied on the same day, when the underlying surface is still dark, the surface must be scraped, vaccu-

umed, and the second layer worked into the surface. The second layer must always be thinner than the first. Where an additional layer is to be applied once the underlying layer has dried and lightened, the surface must be sanded, vaccuumed, and primed using ECODUR® P 12, primer, which must be allowed to dry before the second layer is applied. The second layer must always be thinner than the first. • If parquet is to be fully adhered on the substrate, we suggest using ECODUR® E 31 New or ECODUR® E 33 New, supplemented by advice from our laying specialists. • Always use an expansion strip along walls where the thickness of layers exceeds 5 mm. ECODUR® E 36 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

20 kg bag

Colour:

Grey

Layer thicknesses:

3-40 mm Contact us for advice about thicker layers.

Consumption:

Approx. 1.7 kg/m2 and mm of layer thickness.

Water quantity:

For local steep slopes use approx. 3.4 l/bag. In less steep slopes and normal levelling use approx. 3.7 l/bag.

Working temperature:

Minimum floor temperature 15°C

Working time:

Approx. 40 minutes*1

Ready for foot traffic:

After approx. 1- 2 hours*1

Ready for covering:

After approx. 24 hours*1 *2 The product may remain open for a maximum of 7 days before covering.

Reinforcement:

The product can be reinforced with a fibre mesh

Underfloor heating:

Suitable

Resistance to castor wheels: Not suitable Storage: *1 at 20°C and 65 % RH

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment. *2 with PVC, linoleum, textile floor coverings, and ceramic tiles

ECODUR® E 39 Self levelling compound, coarse Fast-curing Low tension Suitable for levelling of slopes A cement-based, slightly coarser self levelling compound for use on concrete, lightweight concrete, cement-based screed, terrazzo, prefabricated concrete elements, as well as permanently installed chipboards prior to laying of PVC, linoleum, textile floor coverings, or ceramic tiles. For application on other types of substrate, we always recommend consulting us for technical support. Suitable for use in residential areas, offices, and light industrial premises. Suitable for outdoor and permanently or periodically damp environments. Protect with suitable waterproofing or moisture-resistant covering.

Mixing Pour clean, cold water into a mixing bucket, add the powder, and mix mechanically until the compound is lumpfree and homogeneous. In layers with a thickness in excess of 25 mm, 25 kg of ECODUR® E 39 can be supplemented with 12.5 kg of washed quartz sand 22

with a grain size of 0.8-1.2 mm.

Application Only mix as much material that can be applied within the working time. ECODUR® E 39 can be applied by hand or be pumped. Newly applied material must be protected against frost, drafts, and sunlight. Excessively fast drying may cause cracking, deformation, or impaired surface durability.

surface. The second layer must always be thinner than the first. Where an additional layer is to be applied once the underlying layer has dried and lightened, the surface must be sanded, vaccuumed, and primed using ECODUR® P 12, primer, which must be allowed to dry before the second layer is applied. The second layer must always be thinner than the first. • If parquet is to be fully adhered on the substrate, we suggest using ECODUR® E 31 New or ECODUR® E 33 New, supplemented by advice from our laying specialists. • Always use an expansion strip along walls where the thickness of layers exceeds 5 mm. ECODUR® E 39 has been assessed by Byggvarubedömningen and is BASTA-registered.

Pack size:

25 kg bag

Colour:

Grey

Layer thicknesses:

3-40 mm Contact us for advice about thicker layers.

Consumption:

Approx. 1.7 kg/m2 and mm of layer thickness.

Water quantity:

For local steep slopes use approx. 4.2-4.3 l/bag. In less steep slopes and normal levelling use approx. 4.5-4.8 l/bag.

Working temperature:

Minimum floor temperature 15°C

Working time:

Approx. 35 minutes*1

Ready for foot traffic:

After approx. 1- 2 hours*1

Ready for covering:

After approx. 24 hours*1 *2 The product may remain open for a maximum of 7 days before covering.

Reinforcement:

The product can be reinforced with a fibre mesh

Underfloor heating:

Can be used

Resistance to castor wheels: Yes, in layers over 10 mm Storage: *1 at 20°C and 65 % RH

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment. *2 with PVC, linoleum, textile floor coverings, and ceramic tiles 23

REPAIR- AND PATCHING MATERIALS

ECODUR® E 52 Cement-based repair mortar - fine Easy to use Can be covered after approx. 2 hours Very smooth surface A fine-aggregated cement-based repair mortar for use on concrete, screeds, and permanently installed chipboards, prior to laying of PVC, linoleum, textile, or ceramic tiles. For application on other types of substrate, we always recommend consulting us for technical support. Suitable for interior floors in residential areas. Also see section Please observe!

Mixing Pour clean, cold water into a mixing bucket, add the powder, and mix mechanically until the compound is lumpfree and homogeneous. In layers with a thickness in excess of 30 mm, 15 kg of ECODUR® E 52 can be supplemented with 7.5 kg of washed quartz sand with a grain size of 0.8-1.2 mm.

Application Only mix as much material that can be 26

applied within the working time. Apply the product in a suitable layer thickness, allow the material to set for approx. 5 minutes and then gently smooth the surface using a spatula. Newly applied material must be protected against frost, drafts, and sunlight. Excessively fast drying may cause cracking, deformation, or impaired surface durability.

surface. The second layer must always be thinner than the first. Where an additional layer is to be applied once the underlying layer has dried and lightened, the surface must be sanded, vaccuumed, and primed using ECODUR® P 12, primer, which must be allowed to dry before the second layer is applied. The second layer must always be thinner than the first. • If ECODUR® E 52 is applied in smaller local areas and in layer thickness of at least 10 mm, it can be used in public areas with normal wear and under fully adhered parquet, rubber, chlorine-free, or polyolefin coverings. In doubt, contact us for a consultation. ECODUR® E 52 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

15 kg bag

Colour:

Grey

Layer thicknesses:

From 0 to 50 mm. Can be supplemented with washed quartz sand in layer thicknesses over 30 mm.

Consumption:

Approx. 1.4 kg/m2 and mm of layer thickness.

Water quantity:

approx. 4.0- 4.3 l/15 kg powder

Working temperature:

Minimum floor temperature 15°C

Working time:

Approx. 15 minutes*1

Ready for foot traffic:

After approx. 30 minutes*1

Trimming of edges:

After approx. 15- 20 minutes*1

Ready for covering:

After approx. 2 hours*1 *2 The product may remain open for a maximum of 7 days before covering.

Reinforcement:

Can be reinforced with ECODUR® P 10.

Underfloor heating:

Suitable

Resistance to castor wheels: Not suitable Storage: *1 at 20°C and 65 % RH

At least 6 months from the date of manufacture if stored in unopened packaging in a dry and cool environment. *2 with PVC, linoleum, textile floor coverings, and ceramic tiles

ECODUR® E 54 Cement-based repair mortar - coarse 1-40 mm thickness Can be covered after approx. 2 hours Easy to apply A coarse, cement-based repair mortar for use on concrete, lightweight concrete, cement-based screed, prefabricated concrete elements, as well as permanently installed chipboards prior to laying of PVC, linoleum, textile, or ceramic tiles. For application on other types of substrate, we always recommend consulting us for technical support. Suitable for interior floors in residential areas.

Mixing Pour clean, cold water into a mixing bucket, add the powder, and mix mechanically until the compound is lumpfree and homogeneous. In layers with a thickness in excess of 30 mm, 15 kg of ECODUR® E 54 can be supplemented with 7.5 kg of washed quartz sand with a grain size of 0.8-1.2 mm.

Application Only mix as much material that can be 28

ECODUR® E 54 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

15 kg bag

Colour:

Grey

Layer thicknesses:

From 1 to 40 mm. Can be supplemented with washed quartz sand in layer thicknesses over 20 mm.

Consumption:

Approx. 1.5 kg/m2 and mm of layer thickness.

Water quantity:

Approx. 3.6 l/15 kg powder

Working temperature:

Minimum floor temperature 15°C

Working time:

Approx. 15 minutes*1

Ready for foot traffic:

After approx. 1 hour*1

Trimming of edges:

After approx. 15- 20 minutes*1

Ready for covering:

After approx. 2 hours*1 *2 The product may remain open for a maximum of 7 days before covering.

Reinforcement:

Can be reinforced with ECODUR® P 10.

Underfloor heating:

Suitable

Resistance to castor wheels: Not suitable Storage: *1 at 20°C and 65 % RH

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment. *2 with PVC, linoleum, textile floor coverings, and ceramic tiles 29

ECODUR® E 55 Primer-free patching compound Very easy to use From feather finish to 5 mm Primer-free on most substrates A fast-drying, mostly primer-free, cement-based patching compound for use on concrete, lightweight concrete, cement-based screed, prefabricated concrete elements, ceramic tiles, terrazzo, chipboards and gypsum boards. Use prior to laying of PVC, linoleum, or textile floor coverings. For application on other types of substrate, we always recommend consulting us for technical support. Suitable for interior floors in residential areas.

Subfloor preparation The substrate must be load-bearing, durable, completely dry, clean, be free from adhesive residues and other substances that may affect adhesion. If the surface is weak, highly absorbent, or very glossy, it must be primed with the appropriate ECODUR® primer.

Mixing Pour clean, cold water into a mixing bucket, add the powder, and mix mechanically until the compound is lumpfree and homogeneous.

Application Only mix as much material that can be applied within the working time. ECODUR® E 55 can be spread by hand using a spatula. Newly applied material must be protected against frost, drafts, and sunlight. Excessively fast drying may cause cracking, deformation, or impaired surface durability.

Please observe! • If the product is to be applied in multiple layers, the surface of the underlying layer must be completely scraped off, vacuumed, and the subsequent layer worked into the surface. • Always use a measuring bucket to ensure that the right amount of water is added. • ECODUR® E 55 cannot be used under fully-adhered parquet, rubber, chlorine-free, or polyolefin coatings.

ECODUR® E 55 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

15 kg bag

Colour:

Grey

Layer thicknesses:

From 0 to 5 mm.

Consumption:

Approx. 1.3 kg/m2 and mm of layer thickness.

Water quantity:

approx. 4.5 l/15 kg powder

Working temperature:

Minimum floor temperature 15°C

Working time:

Approx. 20 minutes*1

Ready for foot traffic:

After approx. 30 minutes*1

Ready for covering:

After approx. 3 hours*1 *2 The product may remain open for a maximum of 7 days before covering.

Reinforcement:

Can be reinforced with ECODUR® P 10.

Underfloor heating:

Suitable

Resistance to castor wheels: Not suitable Storage: *1 at 20°C and 65 % RH

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment. *2 with PVC, linoleum, textile floor coverings, and ceramic tiles 31

ADHESIVES

ECODUR® S 80 Universal dispersion adhesive Excellent tack Long working time Can be re-activated A solvent-free dispersion adhesive with very low emissions for homogeneous and heterogeneous PVC and CV coverings, linoleum up to 2.0 mm in residential areas, and textile floor coverings with PVC backing.

parts that do not lie flat must be pressed down again after approx. 10-20 minutes. If necessary, repeat this process. Then use a pressure roller crosswise over the entire surface. Clean tools with water immediately after completing work.

Suitable for use on levelled, even, absorbent and non absorbent substrates. Suitable for interior floors and walls.

The ideal laying temperature is 15-25°C, and ideal moisture is between 50 % and 65 % RH/20°C.

Subfloor preparation

Moisture

The substrate must be load-bearing, durable, completely dry, clean, free from adhesive residues and other substances that may impair the adhesion. Uneven substrates should be primed with the suitable ECODUR® primer and levelled with the appropriate ECODUR® levelling compound.

It is vital that the amount of residual moisture in the concrete subfloor is measured and documented so that the covering is not installed on a substrate that is too damp. When laying PVC and diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open linoleum and textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Application Apply the adhesive evenly on the substrate using a trowel with a recommended notched blade adapted to the substrate in question and the covering used. Apply only as much adhesive that can be covered within the working time. Put the covering in place and rub down firmly. Edges, ends, and 34

Please observe!

Consumption

• In order to enable adhesive applied to non absorbent substrates to dry faster, the “double drop” method may be used. With this method, the adhesive is applied to the subfloor using an A5 or A1 notched blade. The covering is then laid directly into the adhesive, pressed down securely, and then immediately pulled back up. Once both sides have dried, re-lay the covering and rub down firmly.

PVC

• Joints may be welded no sooner than after approx. 24 hours. • These recommendations are adhesive recommendations only and do not exempt the user from following the installation instructions provided by the flooring manufacturer.

Absorbent substrate A1/ A2 approx. 200-320 g/m2 Non-absorbent substrate A5 approx. 180-200 g/m2

Textile floors with PVC backing

Absorbent substrate A2/ B1 approx. 250-380 g/m2

Linoleum up to 2.0 mm

Absorbent substrate B1 approx. 320-380 g/m2

Non-absorbent substrate A2/ A5 approx. 250-320 g/m2

Non-absorbent substrate A2 approx. 250-320 g/m2

ECODUR® S 80 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

14 kg bucket

Colour:

Off-white

Consumption:

See the table above.

Working temperature:

Minimum floor temperature 15°C.

Pre-airing time:

Wet set: approx. 5-10 minutes* Semi-wet set: approx. 10-20 minutes* Pressure sensitive application: app. 20-50 minutes*

Working time:

Approx. 1 hour and more*

Can be re-activated with heat:

Up to 90 minutes

Loadable:

24 hours*

Welding of joints:

24 hours*

Final strength:

3 days*

Underfloor heating:

Suitable

Resistance to castor wheels:

Suitable

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C och 65 % RH

ECODUR® S 81 Dispersion adhesive allround Higher resistance against plasticisers Resistant to indentations Extremely high final strength A solvent-free dispersion adhesive with very low emissions for homogeneous and heterogeneous PVC and CV coverings, rubber up to 4.0 mm, LVT, linoleum in sheets and tiles, textile floor coverings, needle punch, and some of the chlorine-free coverings on the market. ECODUR S 81 is extra resistant to plasticizers, allowing the product to maintain its hard adhesive film under PVC coverings. Suitable for use on levelled, even, absorbent substrates. Also suitable for use on certain types of insulating underlay - contact us for a consultation. Suitable for interior floors.

Application Apply the adhesive evenly on the substrate using a trowel with a recommended notched blade adapted to the substrate 36

in question and the covering used. Apply only as much adhesive that can be covered within the working time. Put the covering in place and rub down firmly. Edges, ends, and parts that do not lie flat must be pressed down again after approx. 10-20 minutes. If necessary, repeat this process. Then use a pressure roller crosswise over the entire surface. Clean tools with water immediately after completing work. The ideal laying temperature is 15-25°C, and ideal moisture is between 50 % and 65 % RH/20°C.

Moisture It is vital that the amount of residual moisture in the concrete subfloor is measured and documented so that the covering is not installed on a substrate that is too damp. When laying PVC and diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open linoleum and textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Please observe! • Joints may be welded no sooner than after approx. 24 hours.

Consumption PVC and CV

Very smooth backing A1 approx. 250 g/m2

• These recommendations are adhesive recommendations only and do not exempt the user from following the installation instructions provided by the flooring manufacturer. Linoleum B1 approx. 350 g/m2

Lightly structured backing A2 approx. 300 g/m2

With acoustic backing B1/ B2 approx. 350-450 g/m2

Rubber

A2 approx. 300 g/m2

On insulating underlays A2 approx. 300 g/m2

LVT

Very smooth backing A1 approx. 250 g/m2 Lightly structured backing A2 approx. 300 g/m2

Needle punch

Textile floor coverings

B1/ B2 approx. 350- 450 g/m2

Smooth PVC or foam backing A2 approx. 300 g/m2 Structured backing B1 approx. 350 g/m2 Very structured backing B2 approx. 450 g/m2

Impact sound A1/ A2 approx. reducing 250-300 g/m2 underlay

ECODUR® S 81 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

14 kg bucket

Colour:

Off-white

Consumption:

See the table above.

Working temperature:

Minimum floor temperature 15°C

Pre-airing time:

Approx. 5-20 minutes*

Working time:

Approx. 20-30 minutes*

Loadable:

24 hours*

Welding of joints:

24 hours*

Final strength:

3 days*

Underfloor heating:

Suitable

Resistance to castor wheels:

Suitable

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C och 65 % RH

ECODUR® S 82 Adhesive for textile coverings Fast tack and high final strength For most types of textile floor coverings Easy to apply

A solvent-free dispersion adhesive with very low emissions for most types of textile floor coverings with a synthetic or jute backing, needle punch, and coverings of sisal or coconut fibre.

flat must be pressed down again after approx. 10-20 minutes. If necessary, repeat this process and roll the surface. Clean tools with water immediately after completing work.

Suitable for use on levelled, even, absorbent substrates. Suitable for interior floors.

The ideal laying temperature is 15-25°C, and ideal moisture is between 50 % and 65 % RH/20°C.

Subfloor preparation

Moisture

It is vital that the amount of residual moisture in the concrete subfloor is measured and documented so that the covering is not installed on a substrate that is too damp. When laying diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Application The adhesive is to be applied evenly on the substrate using a trowel with a recommended notch blade adapted to the substrate in question and the covering used. Apply only as much adhesive that can be covered within the installation time. Push firmly into place. Edges, ends, and parts that do not lie

Please observe!

Consumption

• Coverings in sheets must always be rolled out in position in advance in order to allow acclimatisation and to eliminate any possible roll tension.

Textile floors with smooth PVC or foam backing

A2 approx. 360 g/m2

• These recommendations are adhesive recommendations only and do not exempt the user from following the installation instructions provided by the flooring manufacturer.

Textile floors with structured backing

B1 approx. 380 g/m2

Textile floors with very structured backing

B2 approx. 500 g/m2

ECODUR® S 82 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

14 kg bucket

Colour:

Beige

Consumption:

See the table above.

Working temperature:

Minimum floor temperature 15°C.

Pre-airing time:

Approx. 0-10 minutes*

Working time:

Approx. 20 minutes*

Loadable:

24 hours*

Final strength:

3 days*

Underfloor heating:

Suitable

Resistance to castor wheels:

Suitable

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C och 65 % RH 39

ECODUR® S 85 Dispersion adhesive for linoleum Good overwetting Excellent tack Short pre-airing time

A solvent-free dispersion adhesive with very low emissions for linoleum with and without an acoustic backing. May also be used for textile floor coverings, carpet floor tiles and needle punch. Suitable for use on levelled, even, absorbent substrates. Suitable for interior floors.

Application The adhesive is to be applied evenly on the substrate using a trowel with a recommended notch blade adapted to the substrate in question and the covering used. Apply only as much adhesive that can be covered within the working time. Push firmly into place. Edges, ends, and parts that do not lie flat must be pressed down again after ap40

prox. 10-20 minutes. If necessary, repeat this process and roll the surface. Clean tools with water immediately after completing work. The ideal laying temperature is 15-25°C, and ideal moisture is between 50 % and 65 % RH/20°C.

Moisture It is vital that the amount of residual moisture in the concrete subfloor is measured and documented so that the covering is not installed on a substrate that is too damp. When laying diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open linoleum and textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Please observe!

Consumption

• Coverings in sheets must always be rolled out in position in advance in order to allow acclimatisation and to eliminate any possible roll tension.

Linoleum

with acoustic backing B1/ B2 approx. 380- 480 g/m2

B1 approx. 380 g/m2

on insulating underlays A2 ca 300 g/m2 Textile

B1 approx. 380 g/m2

Needle punch B1 approx. 380 g/m2 Corkment

B2 approx. 480 g/m2

ECODUR® S 85 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

14 kg bucket

Colour:

Beige

Consumption:

See the table above.

Working temperature:

Minimum floor temperature 15°C.

Pre-airing time:

Approx. 0-10 minutes*

Working time:

Approx. 25 minutes*

Loadable:

24 hours*

Welding of joints:

24 hours*

Final strength:

3 days*

Underfloor heating:

Suitable

Resistance to castor wheels:

Suitable

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C and 65 % RH 41

ECODUR® S 90 New Parquet adhesive Impact sound improvement up to 9 dB Sanding possible already after 24-48 hrs Function with all surface treatments Elastic SMP-adhesive for several types of fully adhered parquet and hardwood floors. Can be used on absorbent or non-absorbent substrates. For use only in dry, indoor environments.

Application Apply the adhesive to the substrate using a trowel with the recommended notched blade.(see table). Put the parquet into the adhesive, push and then use a pressure roller in order to achieve full overwetting of the adhesive between the substrate and the parquet/hardwood floor. Load with weights if necessary. Also follow the parquet manufacturer's instructions.

Moisture It is vital that the amount of residual mois 42

ture in the concrete subfloor is measured, so that the parquet is not installed on a substrate that is too damp. For parquet and hardwood floors adhered with ECODUR® S 90 New a maximum of 65 % RH applies. In cases where the moisture content of the substrate exceeds these values, we recommend application of moisture barrier ECODUR® P 19. If the subfloor is exposed to additional ground moisture, always contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Please observe! • Never use a conventional water-based primer as an adhesion primer directly below parquet and hardwood floor adhesive. If you have any questions, please contact us for technical advice. • Subfloors with underfloor heating should always be primed with moisture barrier ECODUR® P 19. • These recommendations are adhesive recommendations only and do not exempt the user from following the installation instructions provided by the flooring manufacturer.

Suitable for use with Substrate pulloff strength requirements

Suitable notched blade

Consumption

Multilayer parquet

1.5 MPa

B 11

1000-1200 g/m2

Mosaic parquet

1.5 MPa

800-1000 g/m2

Base parquet

1.5 MPa

800-1000 g/m2

Industrial parquet

1.5 MPa

800-1000 g/m2

Solid parquet blocks

1.5/2.0 MPa*

B 11

1000-1200 g/m2

Solid wood flooring boards

2.0 MPa

B 11

1000-1200 g/m2

Smoked oak

1.5/2.0 MPa*

B 3/B 11*

800-1200 g/m2

Exotic wood

1.5/2.0 MPa*

B 3/B 11*

800-1200 g/m2

* depending on type and format

ECODUR® S 90 New has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

16 kg bucket

Consumption:

See the table above.

Working temperature:

+18°C to +22°C

Humidity:

30-60 % RH.

Working time:

Wet set: 0-35 minutes

Impact sound improvement:

Up to 9 dB according to ISO 10140

Ready for sanding:

24-48 hours

Cleaning:

Adhesive that has not cured is to be wiped off using Brutal Wipes or similar. Cured adhesive must be removed mechanically.

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C.

* at 20°C and 65 % RH 43

ECODUR® S 20 Tackifier Fast drying High tack Roller-adapted bucket A solvent-free tackifier with very low emissions designed to fixate carpet tiles and certain types of textile floor covering in sheets. Suitable for use on levelled, even, absorbent substrates. Suitable for interior floors.

Subfloor preparation The substrate must be load-bearing, durable, completely dry, clean, free from adhesive residues and other substances that may impair the adhesion. Uneven substrates should be primed with the suitable ECODUR® primer and levelled with the appropriate ECODUR® levelling compound. In cases where an existing covering is used as an underlay, it must be stable and free from floor care products and other substances that may impair the adhesion.

Application Apply ECODUR® S 20 evenly using a suitable roller. Allow the adhesive to dry until it becomes transparent before laying, otherwise it produces permanent adhesion. The covering must then be laid and pressed securely into position. 44

The ideal laying temperature is 18-23°C, and ideal moisture is between 20 % and 70 % RH/20°C.

Moisture It is vital that the amount of residual moisture in the concrete subfloor is measured and documented so that the covering is not installed on a substrate that is too damp. When laying diffusion-tight textile floor coverings, a maximum of 85 % RH applies and for diffusion-open textile floor coverings, a maximum of 90 %. In cases where the moisture content of the substrate exceeds these values, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

Please observe! • Do not apply the tackifier in a layer that is thicker than necessary as this may, in certain circumstances, result in excessive adhesion. • Priming using ECODUR® P 10 will reduce consumption and extend working time. • Remember, the laid covering must be completely tension-free, as the tackifier will not keep the covering flat.

• ECODUR® S 20 is not water-soluble and therefore cannot be washed off the floor surface once it has dried. • These recommendations are adhesive recommendations only and do not exempt the user from following the installation instructions provided by the flooring manufacturer.

ECODUR® S 20 has been assessed by Byggvarubedömningen and is registered in BASTA.

Pack size:

10 kg bucket

Colour:

White, turns transparent as it dries.

Consumption:

50-200 g/m2 depending on the absorbency of the substrate and the desired adhesion effect.

Working temperature:

Minimum 18°C to 23°C

Humidity:

20-70 % RH.

Working time:

60–180 minutes, depending on the substrate’s absorption capacity, temperature, and relative humidity.

Cleaning:

Tackifier that has not dried can be washed off with water. Use an adhesive cleaner as Casco LimTvätt or similar to remove half or fully dried tackifier.

Underfloor heating:

Suitable

Resistance to castor wheels:

Suitable

Storage:

At least 12 months from the date of manufacture if stored in unopened packaging in a dry and cool environment, not below 0°C. 45

OTHER

ECODUR® EasyTac LG Adhesive tapes for base coves Installation without pre-airing time Extra heavy tack - for lino and rubber Clean installation A special tape that has been especially developed for quick, clean, and solvent-free installation of linoleum and rubber base coves. Suitable for use on even surfaces such as masonry, smooth plaster, paint, metal, gypsum, wood, concrete, and ceramic. Suitable for interior use only.

Subfloor preparation The substrate must be load-bearing, durable, completely dry, clean, free from silicon and all other substances that may impair the adhesion. Dusty and absorbent substrates must always be pretreated with the appropriate ECODUR® primer. Wallpapers etc. must be firmly secured. Any loose wallpaper etc must be cut at the appropriate height so that the base coves overlaps. The backing of the base cove must be clean and free from dust.

Installation of the base coves The following is required: ECODUR® EasyTac LG, carpet knife, stair pressing tool, rubbing board, and heat gun. 1. Place the adhesive tape on the silicone paper. 2. Apply the adhesive tape on the wall approx. 2-3 mm above the floor and press securely. Ideally, mark the top edge of the base cove to make it easier to locate the height of the product. 3. Cut the sheets. Remember to take the height of the base coves into account and then place them on the floor. 4. Fold the sheets back in half, apply the adhesive, put in place, and press the covering firmly. 5. Fold the other half of the sheets, apply the adhesive, put in place, and press the covering firmly. 6. Pull off the silicone paper section by section, heat, fold, and press the base cove firmly in place.

7. Base coves with linoleum are installed either using cushioned-edge profile or 100 mm strips that are installed separately. The floor-wall angle must always be sealed using silicone or similar after installation of free-standing strips.

you do not eat, drink, or smoke when working with this product. Store out of the reach of children.

Please observe! • ECODUR® EasyTac LG must always be installed in accordance with the instructions.

• ECODUR® EasyTac LG must not be exposed to unusual circumstances such as chemical or mechanical influence.

• Always lay or store rolls on the included silicone paper.

• The product must never be exposed to moisture.

• The product does not require the implementation of any particular work safety measures. However, we recommend that

• In areas with strong grazing light, any transitions between the product and dispersion adhesive may be visible.

• Dry, clean packaging can be recycled. Waste product can be put into household waste.

ECODUR® EasyTac LG has been assessed by Byggvarubedömningen.

Width:

50 / 67 / 97 mm

Pack size:

6 rolls, each 50 metres per box (50 mm). 4 rolls, each 50 metres per box (67 mm). 3 rolls, each 50 metres per box (97 mm).

Colour:

Grey-black scrim carrier, transparent glue.

Working temperature:

Minimum 10°C

Pre-airing time:

None

Working time:

Unlimited

Final strength:

Shortly after laying.

Welding of joints:

Immediately after laying.

Tools:

Carpet knife, stair pressing tool, rubbing board, and heat gun.

Acclimatisation:

Allow sufficient time for acclimatisation (at least 24 hours at 18°C for both ECODUR® EasyTac LG and covering).

Storage:

At least 24 months. Store in a cool, dry location out of direct sunlight. Always store on the included silicone paper. 49

ECODUR® EasyTac VK Adhesive tapes for base coves Installation without pre-airing time Heavy tack - for vinyl and chlorine-free Clean installation A special tape that has been especially developed for quick, clean, and solvent-free installation of PVC and chlorine-free coverings. Suitable for use on even surfaces such as masonry, smooth plaster, paint, metal, gypsum, wood, concrete, and ceramic. Suitable for interior use only.

Installation of the base coves The following is required: ECODUR® EasyTac VK, carpet knife, stair pressing tool, rubbing board, and heat gun. 1. Place the adhesive tape on the silicone paper. 2. Apply the adhesive tape on the wall approx. 2-3 mm above the floor and press securely. Ideally, mark the top edge of the base cove to make it easier to locate the height of the product. 3. Cut the sheets. Remember to take the height of the base coves into account and then place them on the floor. 4. Fold the sheets back in half, apply the adhesive, put in place, and press the covering firmly. 5. Fold the other half of the sheets, apply the adhesive, put in place, and press the covering firmly. 6. Pull off the silicone paper section by section, heat, fold, and press the base cove firmly in place.

7. The joints can be welded immediately after installation.

Please observe! • ECODUR® EasyTac VK must always be installed in accordance with the instructions. • Always lay or store rolls on the included silicone paper. • The product does not require the implementation of any particular work safety measures. However, we recommend that you do not eat, drink, or smoke when working with this product. Store out of the reach of children.

• Dry, clean packaging can be recycled. Waste product can be put into household waste. • ECODUR® EasyTac VK must not be exposed to unusual circumstances such as chemical or mechanical influence. • The product must never be exposed to moisture. • In areas with strong grazing light, any transitions between the product and dispersion adhesive may be visible.

ECODUR® EasyTac VK has been assessed by Byggvarubedömningen.

Width:

97 / 150 mm

Pack size:

3 rolls, each 50 metres, per box (97 mm). 2 rolls, each 50 metres, per box (150 mm).

Colour:

White mesh carrier, transparent glue.

Working temperature:

Minimum 10°C

Pre-airing time:

None

Working time:

Unlimited

Final strength:

Shortly after laying.

Welding of joints:

Immediately after laying.

Tools:

Carpet knife, stair pressing tool, rubbing board, and heat gun.

Acclimatisation:

Allow sufficient time for acclimatisation (at least 24 hours at 18°C for both ECODUR® EasyTac VK and covering).

Storage:

At least 24 months. Store in a cool, dry location out of direct sunlight. Always store on the included sillicone paper. 51

ECODUR® EasyTac T 50 Adhesive tape for textile floor coverings Direct installation – no pre-airing time Extremely high tack Clean installation A special tape for quick, clean, and solvent-free fixation of carpet tiles and textile floor coverings at seams, doorways, transitions, etc. Suitable for use on even substrates such as levelling compound, PVC, linoleum, ceramic tiles, concrete, gypsum board, paint, metal, and chipboards. Suitable for interior use only.

Subfloor preparation The substrate must be load-bearing, durable, completely dry, clean, free from silicon and all other substances that may impair the adhesion. Dusty and absorbent substrates must always be pretreated with the appropriate ECODUR® primer. The backing of the covering must be clean and free from dust.

Please observe! • Always lay or store rolls on the included silicone paper. • The product does not require the implementation of any particular work safety measures. However, we recommend that you do not eat, drink, or smoke when working with this product. Store out of the reach of children.

• ECODUR® EasyTac T 50 must not be exposed to unusual circumstances such as chemical or mechanical influence. • The product must never be exposed to moisture. • ECODUR® EasyTac T 50 is not suitable for use on stairs. Contact us for other alternative tape products.

• Dry, clean packaging can be recycled. Waste product can be put into household waste.

ECODUR® EasyTac T 50 has been assessed by Byggvarubedömningen.

Width:

50 mm

Pack size:

6 rolls, each 25 metres per box.

Colour:

Cream white

Working temperature:

Minimum 10°C

Pre-airing time:

None

Working time:

Unlimited

Final strength:

Shortly after laying.

Acclimatisation:

Allow sufficient time for acclimatisation (at least 24 hours at 18°C for both ECODUR EasyTac T 50 and covering).

Storage:

At least 24 months. Store in a cool, dry location out of direct sunlight. Always store on the included silicone paper. 53

ECODUR® K 30 Impact sound-reducing underlay Highly elastic Easy to cut and easy to install Thermal insulation An elastic impact sound-reducing underlay made from polyurethane and cork. Suitable for use under parquet and hardwood floors. Can be used on absorbent or non-absorbent substrates. Suitable for interior use only.

Installation under fully adhered parquet The product is to be laid, cut and placed edge to edge. A gap of a few mm should be left in connection with walls, doors, and pipes, etc. Fold the sheets back in half, apply the adhesive (same adhesive for both floor covering and underlay) on the floor using a trowel equipped with a B2 notched blade. Place the underlay into the adhesive bed and 54

press firmly in position. Repeat the procedure on the other half of the sheets. Edges and ends, as well as any parts that do not lie flat, must be pressed down again after approx. 10-20 mins. The parquet may only be adhered after 24-48 hours. Choose the notched blade depending of the type of parquet. Both ECODUR® K 30 and the subsequent parquet must be adhered using ECODUR® S 90 New.

Installation under floating parquet The product is to be laid, cut and placed edge to edge. A gap of a few mm should be left in connection with walls, doors, and pipes, etc. If the parquet is to be laid in floating construction, it is not necessary to adhere ECODUR® K 30 to the substrate. ECODUR® K 30 is not a damp proof membrane. If this is required please first lay a 0.20 mm ageing-resistant foil. The ideal laying temperature is 15-25°C, and ideal relative humidity is between 50 % and 65 %.

Moisture

Please observe!

It is vital that the amount of residual moisture in the concrete substrate is measured and documented so that ECODUR K 30 is not installed on a substrate that is too damp. The product itself can withstand a maximum of 65 % RH. In cases where the moisture content of the substrate exceeds this value, we recommend application of an ECODUR® moisture barrier system. Contact us for a consultation. The moisture content in chipboards should be between 8-12 %.

• When installing parquet and hardwood floors without tongue and groove, e.g. Industrial, mosaic, base parquet, etc., use ECODUR® K 30 2 mm!

ECODUR® K 30 has been assessed by Byggvarubedömningen, Sunda Hus Material Data, and is registered in BASTA.

Thicknesses:

2 mm

3 mm

Impact sound improvement:

16 dB (acc. to ISO 10140)

17 dB (acc. to ISO 10140)

Pack size:

30 m2 (1 x 30 metre roll)

20 m2 (1 x 20 metre roll)

Colour:

Brown/black mix

Weight:

33 kg/ roll

Working temperature:

+18°C to +23°C and 30–60 % RH.

Underfloor heating:

Suitable, but the entire construction must be taken into account in order to make a decision in each individual case.

Storage:

At least 24 months. Rolls must be stored upright in a dry, cool environment, not below 0°C. 55

GUIDES AND SYSTEM SOLUTIONS

Primers and moisture barriers

Concrete

PRIMING, REPAIRAND PATCHING

ECODUR® P 10 Universal primer

ECODUR® P 11 Primer for non-absorbent substrates

Main use

3 Possible use (4) With PVC, linoleum, textile floor coverings, and ceramic tiles (5) Between layers approx. 40-50 mins. Prior to gluing of hardwood floors approx. 2 hours. Before levelling approx. 12 hours This guide is to be regarded as guidance. Please find additional information in previous pages about each product.

ECODUR® P 12 Primer for absorbent substrates

ECODUR® P 19 Moisture barrier primer

Repair- and patching materials ECODUR® E 52 Cement-based repair mortar - fine

ECODUR® E 54 Cement-based repair mortar - coarse

ECODUR® E 55 Patching compound

3 Gypsum- or anhydrite screeds Mastic asphalt

3 3

3 3 3 3

Drying time

Layer thickness

Ceramic tiles and terrazzo

Wooden plank subfloors

Substrate with water resistant adhesive residues

Chipboard glued and screwed to studs with max c/c distance of 600 mm.

Concrete and cement-based screed with increased residual moisture content.

3 approx. 0.5-24 hours

approx. 0.5-2 hours approx. 10-60 min. varies (5)

0-50 mm

approx. 2 hours (4)

1-40 mm

approx. 2 hours (4)

3 3 3

0-5 mm

approx. 3 hours (4)

Main use

3 Possible use (1) Up to 3 mm layer thickness (2) With PVC, linoleum, textile floor coverings and ceramic tiles This guide is to be regarded as guidance. Please find additional information in previous pages about each product.

Self levelling compounds

Concrete

SELF LEVELLING COMPOUNDS AND

ECODUR® E 31 New Cross-over self levelling compound

ECODUR® E 33 New Cement-based self levelling compound

ECODUR® E 34 Cement-based self levelling compound

ECODUR® E 36 Fibre-reinforced levelling compound

ECODUR® E 39 Self levelling compound, coarse

3 3

3 0-30 mm approx. 16 hours (2)

0-10 mm

approx. 24-36 hours (2)

3-40 mm

approx. 24 hours/(2)

3 3

3-40 mm

approx. 24 hours (2)

(1)

3 0-20 mm 0-6 mm - 6 hours, 7-12 mm - 12 hrs, 13-20 mm - 24 hrs(2)

Drying time

Layer thickness

Wooden plank subfloors

Mastic asphalt

Gypsum- or anhydrite screeds

Substrate with water resistant adhesive residues

Chipboard glued and screwed to studs with max c/c distance of 600 mm.

Concrete and cement-based screed with increased moisture content, and exterior use.

Ceramic tiles and terrazzo

3 3 3 3

ADHESIVES 3

Main use

This guide is to be regarded as guidance. Please find additional information in previous pages about each product.

LVT floors

Chlorine-free coverings

Floor and wall adhesives

Vinyl (1)

(1) Suitable for both homogeneous and heterogeneous coverings (2) Suitable for both sheets and tiles in max 4 mm. (3) Max 22 mm thickness (4) Smaller areas with minimal light exposure. (5) Max 2.0 mm thickness in smaller residential areas. (6) Coverings with minimal shrinkage (7) Coverings with PVC backing (8) Permanent adhesion (9) Coverings made by specific suppliers.

Rubber (2)

3 Possible use

ECODUR® S 80 Universal dispersion adhesive

ECODUR® S 81 Dispersion adhesive allround

3 3 3 3

ECODUR® S 82 Adhesive for textile coverings ECODUR® S 85 Dispersion adhesive for linoleum Other adhesives ECODUR® S 90 New Parquet adhesive ECODUR® S 20 Tackifier

3 (4)

(9)

3 3 3 3 3 3 3 3

3 Exotic wood varieties

Smoked oak

Hardwood planks (3)

Industrial parquet

Mosaic

Solid parquet blocks

Multilayer parquet

Linoleum

3 3

3 (8)

(8)

Coir, sisal

Needle punch

(6)(7)

Textile, carpet tiles

(5) Textile, sheets

(6)

(8)

3 3 3 3 3 3 3

Min. layer thickness: 20 mm Max. layer thickness: 40 mm Working time: Approx. 40 minutes* Ready for covering: After approx. 24 hours* The product may remain open for a maximum of 7 days before covering.

Fast-drying fibre-reinforced cement-based levelling compound with low shrink stresses.

ECODUR® E 36 Fibre-reinforced levelling compound

Age resistant plastic foil + underlay foam. Alternatively, combi underlay foam and vapour barrier in one.

Byggvarubedömningen and is registered in BASTA.

ECODUR® E 36 has been assessed by

Loose laid. For indoor use on floors in both residential and public environments.

Multilayer parquet

1. Levelling on wooden plank subfloors prior to installing loose laid multilayer parquet.

Systems

Reinforcement mesh

Universal primer ECODUR® P 10 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® E 52 has been assessed by Byggvarubedömningen and is registered in BASTA.

C 35

For additional product information, read the current data sheet at englund-gruppen.se

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system.

Sound, load-bearing, glued and screwed on studs. Residues of paint, oil, varnish, etc. has to be removed.

Wooden plank subfloors

Used as an additive in this system.

ECODUR® P 10

Drying time: 3 hours*

1 x 15 kg bag of ECODUR® E 52 mixed with 3.3 litres of water and 1 litre of ECODUR® P 10

ECODUR® E 52 Cement-based repair mortar - fine

Priming and sealing of gaps in a single step:

Fitted against all walls and other fixed building elements

Expansion strip

All joints must have an overlap of at least 50 mm.

PZG

Min. layer thickness: 20 mm (local deviations down to 12 mm may apply when connected to floor drains). Max. layer thickness: 40 mm Slopes in wet rooms: In shower areas or equivalent 7-20 mm/ length metre, other areas 2-10 mm/length metre. Between floor drain and adjacent walls the slopes can be up to 40 mm/length metre. Working time: Approx. 35 minutes* Ready for covering: After approx. 24 hours* The product may remain open for a maximum of 7 days before covering.

Fast-drying cement-based levelling compound with low shrinkage.

ECODUR® E 39 Self levelling compound, coarse

Base coves can be taped by using ECODUR® EasyTac VK/VK 150.

Consumption: approx. 200-320 g/m2 (notched blade TKB A1/A2 depending on the structure of the backing). Pre-airing time: approx. 10-20 mins* Working time: Approx. 1 hour and more*

Floor and wall adhesive with very good tack and long working time that can be heat re-activated.

ECODUR® S 80 Universal dispersion adhesive

VT-APPROVED PVC FLOORING

2. Levelling on chipboard in wet rooms before installing PVC floors

ECODUR® E 39 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® S 80 has been assessed by Byggvarubedömningen and is registered in BASTA.

Systems

Reinforcement mesh

ECODUR® P 11 has been assessed by Byggvarubedömningen and is registered in BASTA.

For additional product information, read the current data sheet at englund-gruppen.se

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system.

Glued and screwed to studs with max c/c distance of 600 mm.

Chipboards in 22 mm thickness

Consumption: Approx. 100 g/m2 Drying time: 0.5-2 hours*

An extremely quick-drying, solvent-free and fibre-reinforced dispersion primer.

ECODUR® P 11 Primer for non-absorbent substrates

Fitted against all walls and other fixed building elements.

Expansion strip

All joints are to have an overlap of at least 50 mm. Alternatively 2.5 mm point welded steel reinforcement, spread 70 mm. All joints must be overlapped at least one square/opening.

PZG

Reinforcement mesh

ECODUR® E 39 has been assessed by Byggvarubedömningen and is registered in BASTA.

Fitted against all walls and other fixed building elements

Expansion strip

All joints must have an overlap of at least 50 mm. Alternatively 2.5 mm point welded steel reinforcement, with grid pattern 70 mm. All joints must be overlapped at least one square/opening.

PZG

Min. layer thickness: 20 mm Max. layer thickness: 40 mm Working time: Approx. 35 minutes* Ready for covering: After approx. 24 hours* The product may remain open for a maximum of 7 days before covering.

Fast-drying cement-based levelling compound with low shrinkage.

ECODUR® E 39 Self levelling compound, coarse

FLOOR COVERING

3. Levelling on light weight screeds

Systems

EPS Cement

ECODUR® P 12 has been assessed by Byggvarubedömningen and is registered in BASTA.

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system. For additional product information, read the current data sheet at englund-gruppen.se

Load-bearing, durable, clean, and free from adhesive residues and other substances that may affect the adhesion. The moisture content may not exceed 85% RH when installing resillient coverings and 90% RH applies for textile floor coverings.

Concrete

A quick-drying, solvent-free dispersion primer for use on absorbent substrates. Consumption: Approx. 100-150 g/m2 depending on the absorbency of the substrate. Drying time: Approx. 60 minutes*

ECODUR® P 12 Primer for absorbent substrates

Min. layer thickness: 30 mm Max. layer thickness: unlimited Working time: Approx. 60 minutes* Drying time: Approx. 12 hours*

A quick-drying lightweight screed based on cement and expanded polystyrene.

EC350M

A quick-drying, solvent-free dispersion primer for use on absorbent substrates. Consumption: Approx. 100-150 g/m2 Drying time: Approx. 60 minutes*

ECODUR® P 12 Primer for absorbent substrates

Self levelling compound, coarse

Reinforcement mesh

ECODUR® E 39 has been assessed by Byggvarubedömningen and is registered in BASTA.

Systems

Fitted against all walls and other fixed building elements.

Expansion strip

All joints must have an overlap of at least 50 mm. Alternatively 2.5 mm point welded steel reinforcement, with grid pattern 70 mm. All joints must be overlapped at least one square/opening.

PZG

Fast-drying cement-based levelling compound with low shrinkage.

ECODUR® E 39

4. Levelling on chipboard with warm water underfloor heating installed in heat distribution plates

ECODUR® P 11 has been assessed by Byggvarubedömningen and is registered in BASTA.

For additional product information, read the current data sheet at englund-gruppen.se

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system. ** In the event of a load that is more than normal, such as larger bathtubs, heating pumps, very heavy furniture, etc., always c ontact us for technical support.

Glued and screwed to studs with max c/c distance of 600 mm.

Profiled chipboards in 22 mm thickness**

The plates must be thoroughly glued with a construction adhesive, screwed down to the substrate, washed with ethyl alcohol and allowed to dry.

Warm water underfloor heating installed in heat distribution plates.

Consumption: Approx. 100 g/m2 Drying time: 0.5-2 hours*

The primer must be applied in a thin layer across the entire floor surface, including plates, and it is vital that the floor is completely covered.

An extremely quick-drying, solvent-free and fibre-reinforced dispersion primer.

ECODUR® P 11 Primer for non-absorbent substrates

Minimum layer thickness: 10 mm Maximum layer thickness: 30 mm Working time: approx. 20-30 minutes* Ready for covering: After approx. 16 hours* The product may remain open for a maximum of 7 days before covering.

A cement-based quick-drying levelling compound with exceptional flow capacity, low shrinkage, and a very smooth surface.

ECODUR® E 33 New Cement-based self levelling compound

Base coves can be taped by using ECODUR® EasyTac VK/VK 150.

Consumption: Approx. 300 g/m2 (notched blade TKB A2) Pre-airing time: Approx. 5-20 mins* Working time: Approx. 20-30 mins*

A solvent-free, fibre-reinforced dispersion adhesive that is highly resistant to plasticisers, indentation marks. The adhesive gives a very strong film.

ECODUR® S 81 Dispersion adhesive allround

PVC FLOORING

5. PVC on concrete with low absorption/low VCT in areas with heavy commercial use.

ECODUR® E 33 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® S 81 has been assessed by Byggvarubedömningen and is registered in BASTA.

Systems

ECODUR® P 12 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® P 11 has been assessed by Byggvarubedömningen and is registered in BASTA.

For additional product information, read the current data sheet at englund-gruppen.se

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system.

Load-bearing, durable, clean, and free from adhesive residues and other substances that may affect the adhesion.

Dense concrete with low absorption/low VCT. Residual moisture content of max. 85 % RH.

Consumption: Approx. 100-150 g/m2 depending on the absorbency of the substrate. Drying time: Approx. 60 minutes*

A quick-drying, solvent-free dispersion primer.

ECODUR® P 12 Primer for absorbent substrates

If the surface is absorbent:

An extremely quick-drying, solvent-free and fibre-reinforced dispersion primer. Consumption: Approx. 100 g/m2 Drying time: 0.5-2 hours*

ECODUR® P 11 Primer for non-absorbent substrates

If the surface is non-absorbent and free from dust:

Fitted against all walls and other fixed building elements.

Expansion strip

Minimum layer thickness: 5 mm Maximum layer thickness: 30 mm Working time: approx. 20-30 minutes* Ready for covering: After approx. 16 hours* The product may remain open for a maximum of 7 days before covering.

A cement-based quick-drying levelling compound with exceptional flow capacity, low shrinkage, and a very smooth surface.

ECODUR® E 33 New Cement-based self levelling compound

Base coves can be taped by using ECODUR® EasyTac VK/VK 150.

Consumption: Approx. 300 g/m2 (notched blade TKB A2) Pre-airing time: Approx. 5-20 mins* Working time: Approx. 20-30 mins*

A solvent-free, fibre-reinforced dispersion adhesive that is highly resistant to plasticisers, indentation marks. The adhesive gives a very strong film.

ECODUR® S 81 Dispersion adhesive allround

PVC FLOORING

ECODUR® E 33 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® S 81 has been assessed by Byggvarubedömningen and is registered in BASTA.

6. PVC on concrete with a residual moisture content up to 98 % RH in areas with heavy commercial use.

Systems

Primer for non-absorbent substrates

1-K PUR primer

ECODUR® P 19 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® P 11 has been assessed by Byggvarubedömningen and is registered in BASTA.

For additional product information, read the current data sheet at englund-gruppen.se

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system.

Cement-based, moisture-damage resistant, load-bearing (at least 1.0 MPa), and be clean, as well as free from any substances that could affect adhesion. Always contact us for consultation if the surface has a higher RH than 98% or if there is rising ground moisture.

Fresh concrete with residual moisture content up to 98 % RH

Drying time between the layers: approx. 40-50 minutes* Drying time before application of ECODUR® P 11: approx. 12 hours*

Consumption: On concrete with a residual moisture content of up to 95% RH, two layers should be applied with a consumption of approximately 200–250 g/m², depending on the substrate’s absorption capacity. For residual moisture content up to 98% RH, three layers should be applied with a consumption of approx. 300–350 g/m², depending on the substrate’s absorption capacity.

Applied in two or three layers depending on the moisture content.

ECODUR® P 19

Consumption: Approx. 100 g/m2 Drying time: 0.5-2 hours*

An extremely quick-drying, solvent-free and fibre-reinforced dispersion primer.

ECODUR® P 11

A gypsum-based fast-drying crossover levelling compound with very low shrinkage that combines the benefits of gypsum and cement. Layer thicknesses: 7-20 mm Working time: Approx. 20-30 minutes* Ready for covering: 0-6 mm - 6 hrs, 7-12 mm - 12 hrs, 13-20 mm - 24 hrs* The product may remain open for a maximum of 3 days before covering.

ECODUR® E 31 New Cross-over self levelling compound

A solvent-free, very low emission dispersion adhesive with ecxellent tack and a short pre-airing time. Consumption: approx. 380 g/m2 (notched blade TKB B1) Pre-airing time: approx. 0-10 mins* Working time: approx. 25 mins* Base coves can be taped by using ECODUR® EasyTac LG.

ECODUR® S 85 Dispersion adhesive for linoleum

LINOLEUM

ECODUR® E 31 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® S 85 has been assessed by Byggvarubedömningen and is registered in BASTA.

7. Installation of linoleum on weak substrates with asphalt or tar adhesive residues

Systems

Reinforcement mesh

ECODUR® P 12 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® P 11 has been assessed by Byggvarubedömningen and is registered in BASTA.

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system. For additional product information, read the current data sheet at englund-gruppen.se

Completely dry, clean, and free from water-soluble adhesive residues and other substances that may affect the adhesion. Moisture content measured to max. 90 % RH for linoleum.

Weak concrete substrates with asphalt or tar adhesive residues.

A quick-drying, solvent-free dispersion primer Consumption: Approx. 100-150 g/m2 depending on the absorbtion of the substrate. Drying time: Approx. 60 minutes*

ECODUR® P 12 Primer for absorbent substrates

Absorbent substrate, small part of the surface covered by adhesive residues.

An extremely quick-drying, solvent-free and fibre-reinforced dispersion primer. Consumption: Approx. 100 g/m2 Drying time: 0.5-2 hours*

ECODUR® P 11 Primer for non-absorbent substrates

Non-absorbent substrates, most of the surface covered by adhesive residues.

Fitted against all walls and other fixed building elements

Expansion strip

All joints must have an overlap of at least 50 mm.

RENOTEX

Consumption: Approx. 100 g/m2 Pre-airing time: At least 60 mins* Working time: Up to 180 mins*

ECODUR® S 20 Tackifier

CARPET TILES

ECODUR® S 20 has been assessed by Byggvarubedömningen and is registered in BASTA.

8. Carpet tiles on concrete substrates with residual moisture content up to 98 % RH.

Systems

ECODUR® P 19 1-K PUR primer

ECODUR® P 19 has been assessed by Byggvarubedömningen and is registered in BASTA.

For additional product information, read the current data sheet at englund-gruppen.se

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system.

Fresh concrete with residual moisture content up to 98 % RH

Drying time between the layers: approx. 40-50 minutes Drying time before application of ECODUR® P 11: approx. 2 hours*

Applied in two or three layers depending on the moisture content.

Consumption: To be laid in two layers. First layer 100-150 g/m2 depending on the absorbency of the substrate. Second layer 100 g/m2. Drying time: Between the layers approx. 40-50 minutes and approx. 2 hours* before adhering the solid parquet blocks.

A film forming fast drying 1-K PUR primer, specially designed to harmonize with ECODUR®- parquet and hardwood adhesives.

ECODUR® P 19 1-K PUR primer

Consumption: approx. 1000-1200 g/m2 (notched blade B11) Working time: Wet set: 0-35 minutes* Ready for sanding: 24-48 hours*

Elastic SMP-adhesive for several types of fully adhered parquet and hardwood floors.

ECODUR® S 90 NEW Parquet adhesive

Systems

ECODUR® P 19 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® S 90 NEW has been assessed by Byggvarubedömningen and is registered in BASTA.

SOLID PARQUET BLOCKS IN VARIOUS THICKNESSES AND SPECIES

9. Adhering of solid parquet blocks on concrete with warm water underfloor heating. 85% RH

Primer for absorbent substrates ECODUR® P 12 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® E 33 NEW has been assessed by Byggvarubedömningen and is registered in BASTA.

For additional product information, read the current data sheet at englund-gruppen.se

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system.

Sound, load-bearing, clean, and free from adhesive residues and other substances that may affect the adhesion.

Concrete substrate with warm water underfloor heating 85% RH

Consumption: Approx. 100-150 g/m2 depending on the absorption of the substrate. Drying time: Approx. 60 minutes*

A quick-drying, solvent-free dispersion primer

ECODUR® P 12

Minimum layer thickness: 5 mm Maximum layer thickness: 30 mm Working time: approx. 20-30 minutes* Ready for covering with fully adhered parquet and hardwood floors: After approx. 24 hours per 5 mm layer thickness*, but no less than 72 hours regardless of thickness.* The product may remain open for a maximum of 7 days before covering.

A cement-based quick-drying levelling compound with exceptional flow capacity, low shrinkage, and a very smooth surface.

ECODUR® E 33 NEW Cement-based self levelling compound

Parquet adhesive ECODUR® S 90 NEW has been assessed by Byggvarubedömningen and is registered in BASTA.

Layer thicknesses: 7-15 mm Working time: Approx. 20-30 minutes* Ready for covering with fully adhered parquet and hardwood floors: After approx. 72 hours* The product may remain open for a maximum of 7 days before covering.

A gypsum-based fast-drying crossover levelling compound with very low shrinkage that combines the benefits of gypsum and cement.

ECODUR® E 31 NEW Cross-over self levelling compound

ECODUR® E 31 NEW has been assessed by Byggvarubedömningen and is registered in BASTA.

When the surface of the levelling compound has dried, it should be sanded and vacuumed.

Consumption: approx. 1000-1200 g/m2 (notched blade B11) Working time: Wet set: 0-35 minutes* Ready for sanding: 24-48 hours*

Elastic SMP-adhesive for several types of fully adhered parquet and hardwood floors.

ECODUR® S 90 NEW

MULTILAYER PARQUET

10. Adhering of multilayer parquet on weak concrete substrates

Systems

ECODUR® P 12 has been assessed by Byggvarubedömningen and is registered in BASTA.

For additional product information, read the current data sheet at englund-gruppen.se

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system.

Completely dry, clean, and free from water-soluble adhesive residues and other substances that may affect the adhesion. Moisture content measured to max. 65 % RH for parquet and hardwood floors.

Weak concrete.

Consumption: Approx. 100-150 g/m2 depending on the absorbtion of the substrate. Drying time: Approx. 60 minutes*

A quick-drying, solvent-free dispersion primer

ECODUR® P 12 Primer for absorbent substrates

Fitted against all walls and other fixed building elements.

Expansion strip

All joints must have an overlap of at least 50 mm.

RENOTEX Reinforcement mesh

84 ECODUR® P 12 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® E 33 has been assessed by Byggvarubedömningen and is registered in BASTA.

When the surface of the levelling compound has dried, it should be sanded and vacuumed.

Consumption: Approx. 100-150 g/m2 depending on the absorbtion of the substrate.

A quick-drying, solvent-free dispersion primer

ECODUR® P 12 Primer for absorbent substrates

Minimum layer thickness: 5 mm Working time: approx. 20-30 minutes* Ready for covering: The construction must be allowed to dry for at least 72 hours before being coated with thermosetting plastic.* The product may remain open for a maximum of 7 days before covering.

A cement-based quick-drying levelling compound with exceptional flow capacity, low shrinkage, and a very smooth surface.

ECODUR® E 33 New Cement-based self levelling compound

The minimum total thickness of the levelling layers for this type of construction is 20 mm.

EPOXY- OR POLYURETHANE COATINGS

Systems 11. Levelling on chipboards before applying epoxy- or polyurethane coatings in public environments.

Reinforcement mesh

ECODUR® E 39 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® P 11 has been assessed by Byggvarubedömningen and is registered in BASTA.

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system. For additional product information, read the current data sheet at englund-gruppen.se

Glued and screwed to studs with max c/c distance of 300 mm.

Chipboards in 22 mm thickness

Consumption: Approx. 100 g/m2 Drying time: 0.5-2 hours*

An extremely quick-drying, solvent-free and fibre-reinforced dispersion primer.

ECODUR® P 11 Primer for non-absorbent substrates

Fitted against all walls and other fixed building elements.

Expansion strip, self-adhesive with tape

All joints must have an overlap of at least 50 mm. Alternatively 2.5 mm point welded steel reinforcement, with grid pattern 70 mm. All joints must be overlapped at least one square/opening.

PZG

Min. layer thickness: 15 mm Working time: Approx. 40 minutes* Ready for covering: After approx. 24 hours* The product may remain open for a maximum of 7 days before covering.

Fast-drying cement-based levelling compound with low shrinkage.

ECODUR® E 39 Self levelling compound, coarse

Cross-over self levelling compound

alternatively

ECODUR® E 34 Cement-based self levelling compound Layer thicknesses: 0-10 mm. For thicker layers, consult with us. Working time: approx. 30 minutes* Ready for foot traffic: After approx. 3 hours* Ready for covering with PVC, linoleum, and textile: After approx. 24-36 hours* The product may remain open for a maximum of 7 days before covering.

alternatively

Layer thicknesses: 0-30 mm. For thicker layers, consult with us. Working time: approx. 20-30 minutes* Ready for foot traffic: After approx. 2 hours* Ready for covering with PVC, linoleum, and textile: After approx. 16 hours* The product may remain open for a maximum of 7 days before covering.

ECODUR® E 33 New Cement-based self levelling compound

alternatively

Layer thicknesses: 0-20 mm. For thicker layers, consult with us. Working time: Approx. 20-30 minutes* Ready for foot traffic: After approx. 2 hours* Ready for covering with PVC, linoleum, and textile: 0-6 mm - 6 hrs, 7-12 mm - 12 hrs, 13-20 mm - 24 hrs* The product may remain open for a maximum of 3 days before covering.

ECODUR® E 31 New

12. Different options for levelling on concrete

ECODUR® E 34 has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® E 33 NEW has been assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® E 31 NEW has been assessed by Byggvarubedömningen and is registered in BASTA.

Systems

ECODUR® E 39 has been assessed by Byggvarubedömningen and is registered in BASTA.

assessed by Byggvarubedömningen and is registered in BASTA.

ECODUR® E 36 has been

ECODUR® P 12 är has been assessed by Byggvarubedömningen and is registered in BASTA.

* at 20°C and 65 % RH. Note that drying times and consumption for each product apply only in this system. For additional product information, read the current data sheet at englund-gruppen.se

Sound, load-bearing, clean, and free from adhesive residues and other substances that may affect the adhesion.

Concrete substrate with warm water underfloor heating 85% RH

Consumption: Approx. 100-150 g/m2 depending on the absorbtion of the substrate. Drying time: Approx. 60 minutes*

A quick-drying, solvent-free dispersion primer

ECODUR® P 12 Primer for absorbent substrates

For levelling over 5 mm, an expansion strip should be installed against all walls and other fixed building components.

Expansion strip

Layer thicknesses: 3-40 mm. For thicker layers, consult with us. Working time: approx. 35 minutes* Ready for foot traffic: After approx. 1-2 hours* Ready for covering with PVC, linoleum, and textile: After approx. 24 hours* The product may remain open for a maximum of 7 days before covering.

ECODUR® E 39 Self levelling compound, coarse

Layer thicknesses: 3-40 mm. For thicker layers, consult with us. Working time: approx. 40 minutes* Ready for foot traffic: After approx. 1-2 hours* Ready for covering with PVC, linoleum, and textile: After approx. 24 hours* The product may remain open for a maximum of 7 days before covering. alternatively

ECODUR® E 36 Fibre-reinforced levelling compound

LARGER PROJECTS? WE CAN ASSIST YOU. We have both the expertise and the equipment to help you with your pumping projects. For more than 20 years, we’ve been helping customers with pumping of self levelling compounds.

1000 m2 layed in just over an hour Our latest pump is equipped with a 40 metre long hose and has a capacity of 4.5 tons an hour, which means that a job of approx. 1,000 m2 in a layer thickness of 3 mm will not take more than one hour to complete. Most ECODUR® products have good flow capacity, fast curing, and a smooth surface finish - the perfect substrate on which to lay a floor.

Our pump specialists will help you Give us a call. If in doubt wether your substrate is suitable or not, we’ll perform an onsite inspection first. Robin Malcic +46 (0)704 37 89 15

Gothenburg Bohuslän Halland

Jacob Tawar +46 (0)707 38 31 13

Gothenburg Bohuslän Halland

Johan Karlsson 0704-37 89 00

Stockholm Uppland Västmanland

Patrik Brekkestö 0706-71 71 52

Småland Blekinge Östergötland

Leif Jönsson +46 (0)707 37 07 07

Skåne Halland

Jonas Svensson +46 (0)720 707 444

Rest of Sweden

Art no 125387 September 2026.100

ENGLUND-GRUPPEN FLOORING AB www.englund-gruppen.se Kryptongatan 20 SE-431 53 Mölndal Tel +46 (0)31 670 170 goteborg@englund-gruppen.se

Västbergavägen 43 SE-126 30 Hägersten Tel +46 (0)8 556 30 880 stockholm@englund-gruppen.se

Flygplansgatan 8 SE-212 39 Malmö Tel +46 (0)40 18 47 90 malmo@englund-gruppen.se

Slöjdaregatan 2 SE-393 53 Kalmar Tel +46 (0)480 47 96 86 kalmar@englund-gruppen.se