Völkl Snowboards | Cashew Splitboad mounting manual (English)

Vรถlkl Snowboards | Cashew Split mounting manual!

OVERVIEW CASHEW SPLIT

tip an tail clips

climbing skins

skin bag with micro fleece

separating foil for climbing skins

metal hooks

aluminium slider tracks with t-nuts H-shaped alignment guide rubber gaskets

climbing heels touring brackets

slider pins

1/8

pucks incl. discs

Völkl Snowboards | Cashew Split mounting manual!

1. Touring Brackets and Climbing Heels Preparation • Bend the climbing heels [1.b] slightly to make them fit into the lids • Place the climbing heel brackets into the lids [1.c]; make sure the rubber bend faces up • Put the lid on top of the pad Mounting • Screw touring brackets [1.a] into the appropriate inserts on the board • Screw climbing heels (lid, brackets, and pad) into the appropriate inserts with the bend in the wire facing towards the nose [1.d] Tips and Tricks • For more effective and easier hiking fold up climbing heels when hiking in steep terrain. Keep heels folded down when hiking in flat terrain.

[ 1.a ]

[ 1.b ]

[ 1.c ] 2/8

[ 1.d ]

Völkl Snowboards | Cashew Split mounting manual!

2. Pucks and Discs Preparation • Stretch rubber gaskets [2.a] slightly and place into bottom of the pucks [2.b] Mounting • Slide two pucks including discs into the H-shaped alignment guide [2.e]; make sure to use one disc each with parallel slots [2.c] and with the slots next to each other [2.d] • Slide discs [2.c & 2.d] into the pucks [2.b] and choose desired stance angle; for angles larger than 37° use A-marking, for angles smaller than 36° use the B-marking [2.h] • The disc with the slots next to each other [2.d] must point towards the toe edge Tips and Tricks • Make sure the pucks lock up with the H-shaped guides [2.g]. The slider pins must fit through the holes in the aluminium slider tracks and have some leeway (important when assembling the board with ice and snow sticking to the slider tracks). [ 2.c ] [ 2.a ]

[ 2.d ]

[ 2.b ] [ 2.e ]

[ 2.f ]

[ 2.g ] 3/8

[ 2.h ]

Völkl Snowboards | Cashew Split mounting manual!

3. Stance Preparation • Place board on a flat ground (floor or table); close tip and tail clips as well as metal hooks completely [3.a] • Choose desired stance width and place bindings onto the center axis of the board; mark center of the bindings with a pen on the boardsʻ center axis • Make sure the disc with the slots next to each other always points towards the toe edge [3.c] Mounting • Position H-shaped guide with the hole in the center over the marked spot [3.b] and tighten pucks containing the discs • Remove the H-shaped guide, slide the aluminium slider tracks completely over the pucks and push the slider pins through the holes in the aluminium slider tracks to test the correct mounting of the pucks [3.d]

Tips and Tricks • If the discs and your markings don't fit, swap from A to B or B to A. • The slider pins should have some leeway and easily slide through the holes.

[ 3.a ]

[ 3.b ]

[ 3.c ] 4/8

[ 3.d ]

Völkl Snowboards | Cashew Split mounting manual!

4. Bindings Preparation • Position rubber gaskets [4.a] in the center of the aluminium slider tracks [4.b] Mounting • Mount the bindings with a 0°/0° angle onto the slider tracks [4.e], as the feet must be aligned straight when hiking (use T-nuts provided [4.c] and your own binding screws) • Slide the fully-assembled aluminium slider tracks including the bindings over the pucks mounted on the board; secure their position with the slider pins [4.d] pushed through the holes in the slider

Tips and Tricks • To avoid damages to board and bindings the bindings must not protrude too much from the slider tracks [4.f].

• The binding screws must be flush with the T-nut bottom [4.g] or else the slider tracks [4.b] don't fit over the pucks. You may have to use shorter screws or thicker washers with your bindings.

[ 4.a ]

[ 4.b ]

[ 4.d ] [ 4.c ] [ 4.e ]

[ 4.f ] 5/8

[ 4.g ]

Völkl Snowboards | Cashew Split mounting manual!

5. Hike Mounting • Remove slider pin and aluminium slider tracks including bindings [5.a] • Open tip and tail clips and take board apart [5.b] • Turn tip and tail clips as well as metal hooks inwards until they don't protrude anymore [5.b] • Remove protective foil from skins; use Völkl Skin Pin System to attach skins at nose and apply them over the entire board length to the tail [5.c] • Attach aluminium slider tracks including bindings to the touring brackets and secure with slider pins [5.d] Tips and Tricks • Before attaching the skins clean and dry board base with the micro-fleece on the skin bag provided.

• Make sure to keep the skins' glue dry and clean!

• In order to have more pressure on your edges while ascending on ice or hard-pack do not swap the board halves as the Cashew Split has a convex powder base (elevated edges).

• To protect your slider pins from getting lost you should fix them somewhere at your bindings [5.a].

[ 5.a ]

[ 5.b ]

[ 5.c ] 6/8

[ 5.d ]

Völkl Snowboards | Cashew Split mounting manual!

6. Ride Mounting • Remove slider pins from touring brackets and pull off the aluminium slider tracks including bindings [6.a] • Remove climbing skins beginning at the tail and cover the glued sides with the separating foil • Assemble board using the four metal hooks and the tip and tail clips [6.b] • Slide aluminium sliders including bindings over the pucks and secure with slider pins [6.d] Tips and Tricks • Place board on edge for easier mounting of the slider tracks from above.

• To avoid damages to the board make sure the tip and tail clips are always completely closed when riding [6.b].

• For easier use of the skins cut separating foil into halves and use both sides of each half for one skin.

• To protect your slider pins from getting lost you should fix them somewhere at your bindings [6.d].

[ 6.a ]

[ 6.b ]

[ 6.c ] 7/8

[ 6.d ]

Völkl Snowboards | Cashew Split mounting manual!

7. Miscellaneous • If the metal hook screws between nose/tail and bindings come loose use lock-tite and tighten them again.

• Always take your crampons on the mountain to make sure you have good foothold even on steep or icy terrain.

• All Völkl Fastec models' binding screws fit the t-nuts provided!

• Make sure to check tightness of all screws prior to every tour!!!

• Check function of the slider tracks by sliding them onto and off pucks. Make sure the slider pins move loose and freely through both holes at the end of the aluminium slider tracks!!!

• More information at: www.voelkl-snowboards.com

8/8