TELESCOPIC WHIPS
TRABUCCO FISHING RANGE 2024 ENERGHIA RTX LIGHT-POLE • Ultralight blanks made from low resin content CX-2 Nano-Tek carbon • Sharp and soft action at the same time • Hi-tech joints for a perfect action curve and low oscillation (X-Joint) • Spliced top section with solid carbon tip and spare tubular top section, supplied with each rod • Anti Grip sections to avoid joint’s sticking in wet conditions • Special tangle-free line connector (to be glued) • Inner screw butt cap with removable EVA overcap and rubberized, ribbed handle for nice control and comfort • Velcro band to fix the rig’s winder during transport
CNX Carbon Nano Tubes it is an extreme material, characterized by an incomparable compactness, due to a very high ratio between the ultrafine High Modulus carbon sheets and the resins that cement the multiple layers. The nanometric resins are the only ones capable of penetrating into infinitesimal spaces, optimizing the cohesion between the fibers to obtain an extremely precise elastic response and an exceptional resistance. X-JOINT TECHNOLOGY
Thanks to the use of multi-axial carbon sheets, the X-Joint allow to obtain perfect action curves, absorbing all the torsions to which the blank is subjected, increasing the structural resistance and the response to stresses. X-Joint is therefore able not only to improve the section’s links, but rather assist the whole structure for maximum performance. Definitely the best joints ever made! TRADITIONAL REINFORCEMENT
45° REINFORCEMENT (X-JOINT)
• Stress is concentrated at both ends • Dead spots, risk of breakage
• Stress is dispersed along the blank • Perfect curve, no breakage risk
• Perfect curve, without dead spots. • Unique coexistence of flexibility and stiffness • Higher structural strength, because stress is dispersed through the blank, instead of being concentrated on joint’s ends. • Less oscillations at the end of casting, which means quicker re-alignment of guides. Within X-Joint by Trabucco, the carbon cloth is wound by two directions, and such construction is visible on top end of each section. 0° UNI-DIRECTIONAL CARBON
90° SCRIM CARBON
+ The carbon fibers oriented along the longitudinal rod’s axis (0° unidirectional carbon) provide great resistance to linear traction.
In the rods produced with the computer assistance, the joint’s precision is so high that, when they are wet, it is possible to form the vacuum, resulting in very tight section’s locking. The problem is prevented by creating thin air chambers through cross bands milled on the male side of each joint. THE FANTASTIC ROLLING CONNECTOR Each Energhia XR Master-T rod comes with a special line connector, to be glued on top tip, that eliminates line tangles thanks to a rotating device, similar to a microscopic swivel, which is connected to a string that ends with a slight head. The weight of such connector is absolutely irrelevant, but its benefits can be immediately seen. The swivelling connector enables to link the rig without tangle risk.
X-JOINT ± 45° CARBON TECHNOLOGY
+ The X-Joint carbon fibers, oriented at ±45° to rod’s axis, are able to absorb and disperse the torque, improving the joint’s performance and saving the rest of the section.
The carbon fibers oriented at 90° to longitudinal rod’s axis enable the cross section to resist the compression caused by strong flexion.
(to be glued on tip top)
HOW TO CONNECT THE RIG LINE 1. Make two loops on top of the rig line; one large, the other fairly small. 2. Wrap the main loop around the tip string and tighten it. 3. To remove the rig, simply pull the small loop and it will be released.
TWIN TOP! 1
In addition to the classic spliced top section, with the solid carbon tip and the tangle free line connector, the Energhia XR is equipped with a second tubular top, suitable for sea fishing or to create a super-light bolo.
8APENTD*aabgba+ 134-36-170 8APENTD*aabgch+ 134-36-180 8APENTD*aabgde+ 134-36-190 8APENTD*aabgeb+ 134-36-160
12
@TrabuccoFishing
6.00
129
150
6
7.00
129
210
7
8.00
129
270
8
9.00
129
360
9
2
3
THE VELCRO BAND
A light Velcro band, supplied with the rod, enables to fix the rig’s winder to the butt, when it’s stored in the holdall with the rig on.