Page 1

Stringing Equipment Equipment for laying Underground Cables

2012 Catalogue


Index

Pullers ARS200

U 10

ARS404

U 40

ARS505

U 50

ARS607

U 60

Additional Devices Remote controls (AX)

U 70

Electronic pull and speed recorder (DLR300)

U 80

Hydraulic Drum Elevators Heavy duty drum elevators (CVI600-CVI810-CVI816)

U 90

Heavy duty drum elevator (CVI830)

U 100

Mechanical drum trestle (CVM)

U 101

Reels and Steel Rope Standard reels (BOF) / Detachable reels (BOC)

U 105

Anti-twisting steel braided rope (FUX) / High tech anti-twisting steel braided rope (FUH)

U 110

Accessories Cable rollers (ACR)

U 120

Corner rollers (ACR)

U 130

Cable guiding devices (ACR)

U 140

Cable guiding devices (ACR)

U 150

Cable guiding devices (ACR)

U 160

Cable guiding devices (ACR)

U 170

Cable guiding devices (ACR)

U 180

Fiberglass rods (ACV)

U 190

Fiberglass rods (ACV)

U 200

Accessories for fiberglass rods (ACV)

U 210

Pulling eyes (CX)

U 220

Reusable pulling eyes (CX)

U 230

Head type sock joints (GCL-GCT)

U 240

Sock joints (GCP/GCA-GCS)

U 250

Connecting devices (GGT-ALG)

U 260


PULLERS


Hydraulic Puller

ARS200 The machine is suitable to string one rope. The bull-wheel grooves are made of heat treated steel.

695

Performance

Configuration

Note: the basic machine performance is calculated at 20°C and at sea level

Negative self-acting hydraulic brake Hydraulic dynamometer with set-point and automatic control of maximum pull On board reel winder with automatic level wind and special reel BOF370 for 500 m of Ø 8 mm rope

Characteristics

Additional Devices

Max pull Speed at max pull Max speed Pull at max speed

15 kN 0.7 km/h 3.6 km/h 4 kN

800

1425

200 mm ALL102 8 mm 500 kg ALL105

Bull-wheel diameter Max rope diameter Mass (without rope)

Engine Gasoline Cooling system Electrical system

13 kW (18 hp) ALL107 air ALL111 12 V ALL112

Hydraulic Transmission Closed hydraulic circuit for stepless speed variation in both rotating directions. ALL120 ALL107

ALL111

Pulling rope locking device when capstan is used (compulsory for EC market) Rigid axle and towing bar detachable, for manual towing Capstan (diameter=220 mm equipped with guide rope rollers) Swivel guide rope roller Trailer for towing at max speed of 80 km/h with mechanical parking brake. Towing shaft with inertial braking system. Hook with Ø 40 mm eye. Lighting system included Noise reduction and protective covers

1425

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 10

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Hydraulic Puller

ARS404 The machine is suitable to string one rope. The bull-wheel grooves are made of heat treated steel. The puller has been specifically designed for laying underground cables.

Performance

Configuration

1380

Max pull Speed at max pull Max speed Pull at max speed

32 kN 1.4 km/h 4.5 km/h 10 kN

Note: the basic machine performance is calculated at 20°C and at sea level

Characteristics 1580

Bull-wheel diameter Max rope diameter Mass (without rope)

250 mm 10 mm 1000 kg

Engine Diesel Cooling system Electrical system

2450

Hydraulic Transmission

Additional Devices

Closed hydraulic circuit for stepless speed variation in both rotating directions.

ALL110

1700

2300

ALL110

25 kW (34 hp) water 12 V

600

Negative self-acting hydraulic brake Hydraulic dynamometer with set-point and automatic control of maximum pull Hydraulic oil cooling system Control instruments for hydraulic system and Diesel engine Rigid axle for towing at max speed of 30 km/h with mechanical parking brake On board reel winder with automatic level wind and special reel for 1000 m of Ø 10 mm rope Electronic pull and speed recorder kit (instrument not included) Pull pre-setting system Mechanical front stabiliser Grounding connection point

1216

ALL112

Underground cable pulling attachment ALL112 Trailer for towing at max speed of 80 km/h with mechanical parking brake. Towing shaft with inertial braking system. Hook with Ø 40 mm eye. Lighting system included ALL120 Noise reduction and protective covers DLR300 Electronic pull and speed recorder

1500

DLR300

3950

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 40a

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Hydraulic Puller

ARS505 The machine is suitable to string one rope. The bull-wheel grooves are made of heat treated steel. The puller has been specifically designed for laying underground cables.

Performance

Configuration

1560

Max pull Speed at max pull Max speed Pull at max speed

50 kN 1 km/h 5 km/h 10 kN

Note: the basic machine performance is calculated at 20°C and at sea level

Characteristics

1970

Bull-wheel diameter Max rope diameter Mass (without rope)

350 mm 14 mm 1850 kg

Engine Diesel Cooling system Electrical system

2440

ALL110

34 kW (46 hp) water 12 V

Hydraulic Transmission Closed hydraulic circuit for stepless speed variation in both rotating directions.

Additional Devices Underground cable pulling attachment ALL112 Trailer for towing at max speed of 80 km/h with mechanical parking brake. Towing shaft with inertial braking system. Hook with Ø 40 mm eye. Lighting system included DLR300 Electronic pull and speed recorder

2300

ALL110

1700 600

Negative self-acting hydraulic brake Hydraulic dynamometer with set-point and automatic control of maximum pull Hydraulic oil cooling system Digital meter counter Control instruments for hydraulic system and Diesel engine Rigid axle for towing at max speed of 30 km/h with mechanical parking brake On board reel winder with automatic level wind and special reel for 700 m of Ø 14 mm rope Noise reduction protection Electronic pull and speed recorder kit (instrument not included) Pull pre-setting system Mechanical front stabiliser Grounding connection point

1216

ALL112 1570

DLR300

4050

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 50

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Hydraulic Puller

ARS607 The machine is suitable to string one rope. The bull-wheel grooves are made of heat treated steel. The puller has been specifically designed for laying underground cables. The machine is provided with twin speed device allowing to choose between two different working positions: high pull-low speed or high speed-low pull.

Performance

Configuration

1850

Max pull Speed at max pull Max speed Pull at max speed

100 kN 0.5 km/h 4 km/h 12.5 kN

Note: the basic machine performance is calculated at 20°C and at sea level

Characteristics

2390

Bull-wheel diameter Max rope diameter Mass (without rope)

400 mm 16 mm 2500 kg

Engine Diesel Cooling system Electrical system

2800

ALL110

48 kW (65 hp) water 12 V

Hydraulic Transmission Closed hydraulic circuit for stepless speed variation in both rotating directions.

2300

Additional Devices

1700 600

ALL112 1780

DLR300

4350

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Cable remote control kit (instrument not included) ALL059 Radio remote control kit (instrument not included) ALL110 Underground cable pulling attachment ALL112 Trailer for towing at max speed of 80 km/h with mechanical parking brake. Towing shaft with inertial braking system. Hook with Ø 40 mm eye. Lighting system included ALL116 Free-wheel device (max pay-out speed 15 km/h) DLR300 Electronic pull and speed recorder ALL051

1216

Keep you updated on:

Negative self-acting hydraulic brake Hydraulic dynamometer with set-point and automatic control of maximum pull Hydraulic oil cooling system Digital meter counter Control instruments for hydraulic system and Diesel engine Rigid axle for towing at max speed of 30 km/h with mechanical parking brake On board reel winder with automatic level wind and special reel for 1000 m of Ø 16 mm rope Noise reduction protection Electronic pull and speed recorder kit (instrument not included) Pull pre-setting system Mechanical front stabiliser Grounding connection point High pull/low speed & low pull/high speed selection

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 60a

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


ADDITIONAL DEVICES


Remote Controls

AX CABLE REMOTE CONTROL AXC005 The cable remote control Mod. AXC005 allows to operate same controls of the machine in a different position compared to the control panel. In particular it is complete with the following devices: • • • •

setting of the pull/tensioning value control of direction and speed rotation of the bull wheels control of Diesel engine rpm stop all the functions of the machine

Technical Characteristics

Dimensions

Applicability

These devices have the capacity to operate until a maximum distance of 10 meters. Anti-shock material box having IP54 grade.

610 x 150 x 265 mm

The cable remote control AXC005 can only equip ARS607.

Mass 4.5 kg

RADIO REMOTE CONTROL AXH007 The radio remote control Mod. AXH007 allows to operate same controls of the machine in a different position compared to the control panel. In particular it is complete with the following devices: • • • •

setting of the pull/tensioning value control of direction and speed rotation of the bull wheels control of Diesel engine rpm stop all the functions of the machine

Technical Characteristics

Dimensions

Applicability

These devices have the capacity to operate until a maximum distance of 150 meters. Anti-shock material box having IP65 grade.

235 x 150 x 160 mm

The radio remote control AXH007 can only equip ARS607.

Mass 1.2 kg

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 70

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Electronic Pull and Speed Recorder DLR300

Electronic device that allows the monitoring of stringing operations by recording the following data: • • •

applied pull, with the exceeding control of a limit value stringing speed stringing length

The unit can also give the following information for any single record: • date and hour of monitoring start • value for the limiting control value • sampling distance time • date and hour of monitoring end In addition there is a printer with real time function; it is also possible to print a graph of the record. It is possible to connect the unit to the PC for downloading the data or to download data on external Pen drive by using USB port on the unit. The recorder is equipped with a rigid box for transport, connecting cables, software disk for PC connection and protecting case in PVC, electrical power adapter and adapter plugs for the connection to the machine.

Technical Characteristics

Dimensions

Voltage

345 x 200 x 65 mm

Display

10 ÷ 28 V 2 rows with 16 digits

Mass 1.5 kg

Applicability

Additional Devices

The unit can be connected to all Tesmec machines equipped with additional device ALL053.

DLK301 Stand support

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 80

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


HYDRAULIC DRUM ELEVATORS


Heavy Duty Drum Elevators

CVI600-810-816 Tesmec drum elevators are made of welded steel with a protective coating;the frames are detachable to reduce dimensions during transport. The lifting operation is made by means of hydraulic cylinders. The drum elevators must be completed with the optional CDR or CDT. The drum elevator Mod. CVI816 includes the main frame with a mechanical disk braking system and it is already equipped with support with self locking fixing wedges for wooden conductor reels. The picture shows the CVI with the CDR.

Model

A 2140 2500 2800

CVI600 CVI810 CVI816

Bmin 500 800 1500

Bmax 1500 1850 2600

Dimensions [mm] Cmin Cmax 580 1340 720 1725 960 1770

D 640 740 900

Emin 1200 1500 2000

Emax 2500 3200 3400

Shaft Ø [mm] 40 40 70

Capacity [kN] 70 100 160

Mass [kg] 430 550 1340

Braking System

E

C

Model CVI600 CVI810 CVI816

one manual disk brake (max torque 1 kN x m) one manual disk brake (max torque 2.3 kN x m) two manual disk brakes (max torque 6 kN x m)

Additional Devices Model

A

CVI600 CVI810 CVI816

B

CDF

Support with self-locking Special driver with fixed fixing wedges for wooden wedges for steel conductor conductor drums reels (*) CDR002 CDTxxx CDR057 CDTxxx included CDTxxx

(*) reel drawing is required

D

D

CVI + CDR

X

D

D

CVI + CDT (*)

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 90

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Heavy Duty Drum Elevator

CVI830 This drum elevator is made of welded steel with a protective coating; the frame is partially detachable to reduce dimensions during transport. The drum elevator includes the main frame with supports for wooden or for steel made reels (to be specified in the order) and 2 mechanical disks braking system. Note: in case of steel made reels, the drawing is required.

Model

A 3000

CVI830

Bmin 1600

Bmax 2800

Dimensions [mm] Cmin Cmax 1550 2150

D 600

Emin 3000

Emax 4600

Shaft Ø [mm] 140

Capacity [kN] 300

Mass [kg] 1600

Configuration Two manual disk brakes (max torque 3.5 kN x m) Support for wooden or steel made reels

C

E

A

B

D

D

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 100

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Mechanical Drum Trestle

CVM Mechanical drum trestle with adjustable position. The jacks lift by a screw operated by a crank handle. Wide base support assures the reel stability. The length of screw is suitable to different reel dimensions. Made of highly galvanized steel to lift reels of diameter between 400 and 3000 mm.

Capacity [Kg] 1500 3000 5000 10000

Model CVM007 CVM205 CVM407 CVM802

Reel diameter [mm] 400 - 1800 700 - 2600 930 - 3000 1160 - 3000

Height [mm] 74 100 130 130

Mass [Kg] 30 64 70 88

ACCESSORIES Galvanised collar

Alloy tubolar shaft with bearings Model CDS031 CDS032 CDS027 CDS028 CDS029

Length [mm] 1800 2050 1500 1800 2050

Ø [mm] 90 90 75 75 75

Capacity [Kg] 10000 10000 5000 5000 5000

Mass [Kg] 22.2 25.3 14.6 18.5 19.6

Model CDS038 CDS039 CDS033 CDS034 CDS035 CDS036

CDO040 CDO041 CDO042

Axle Ø [mm] 60 75 90

Mass [Kg] 1.2 1.5 1.7

Galvanised fixing cones

Galvanised steel tubolar shaft with ball-bearing Length [mm] 1800 2050 1500 1500 1800 2050

Model

Ø [mm] 90 90 60 75 75 75

Capacity [Kg] 10000 10000 3000 5000 5000 5000

Mass [Kg] 22.2 25.3 18 14.6 18.5 19.6

Model CDO044 CDO045 CDO046

Ø [mm] 85 - 130 110 - 150 65 - 115

Axle Ø [mm] 75 90 60

Mass [Kg] 7 8.5 3

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 101

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


REELS AND STEEL ROPE


Reels

BOF-BOC The reels are made of welded steel with protective coating. Each reel is provided with two cross supports and connecting bolts in separate package.

BOF

BOC

Standard Reels - BOF

C

D

Ø 50

Standard Reels Model BOF010 BOF020

B

A

A 420 420

Dimensions [mm] B C 560 570 560 570

D 1100 1400

Mass [kg] 53 73

A 420 420

Dimensions [mm] B C 560 590 560 590

D 1100 1400

Mass [kg] 75 86

Detachable Reels - BOC The reels are made of welded steel with protective coating. A detachable side and the conical drum facilitate removal of rope or conductor coil.

Detachable Reels Model BOC040 BOC050

D

C

Ø 50

Reel Max Capacity for Anti-Twisting Braided Rope [m] (See page U 110) Reels Ø Rope 6 8 10 13 16

B

A

Cross support - BOS360

BOF010 BOF020 BOF030 BOF330 BOC040 BOC050 BOC310 BOC320 7700 4300 2700 1600 1000

13400 7500 4850 2720 1800

27300 15100 9800 5550 3750

93200 52400 33550 19850 13100

6950 3800 2350 1400 910

13200 7250 4570 2400 1700

43400 24450 15600 9250 6100

76000 42750 27350 16200 10650

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 105

Mass with bolts: 2.6 kg &HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Anti-Twisting Steel Braided Rope

FUX-FUH STANDARD - FUX Anti-twisting galvanised steel rope, made up of braiding strands. Advantages: • high flexibility • complete stability to rotation • homogeneous distribution of pressure between the elementary wires • increased efficiency during stringing operations • strands with individual galvanized elementary wires

Model

Nominal diameter

FUX006 FUX008 FUX010 FUX013 FUX016

[mm] 6 8 10 13 16

Indicative lubricated linear mass* [kg/m] 0.11 0.22 0.35 0.55 0.84

Minimum breaking load [kN] 21.5 42.6 68 101 160

Standard length** [m] 1800-3600 1600 1200 800-1600 900

*According to production variations, the linear mass may change

HIGH TECH - FUH Rope having same technological advantages of FUX, but made with high tensile strength steel strands allowing higher working and breaking loads with the same linear mass.

Model FUH009 FUH013 FUH016

Nominal diameter [mm] 9 13 16

Indicative lubricated linear mass [kg/m] 0.25 0.50 0.76

Minimum breaking load [kN] 60 121 183

Standard length** [m] 1600 800-1600 900

**The rope is also available in longer continuous sections (without connectors) up to 7000 m Note: sections are supplied with spliced eyes in the following models: • ALF001 for diameters 06-10 mm • ALF002 for diameters 13-16 mm

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 110

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


ACCESSORIES


Cable Rollers

ACR ACR001

STANDARD

ACR191

Made of galvanized steel and mounted on protected ball bearings, suitable for cables up to ø 120 mm. Also available with Al roller (model ACR191).

Dimensions (l x w x h) [mm] 300 x 240 x 250 300 x 240 x 250

Model ACR001 ACR191

Rollers dimensions (l x Ø x Ø) [mm] 190 x 110 x 76 190 x 125 x 76

Max working load [kg] 170 200

Mass

Rollers dimensions (l x Ø x Ø) [mm] 216 x 80 x 80

Max working load [kg] 300

Mass

Rollers dimensions (l x Ø x Ø) [mm] 100 x 60 x 50

Max working load [kg] 280

Mass

[kg] 3.8 4.7

HEAVY DUTY Specifically designed for heavy and thick cables up to ø 180 mm. Made of galvanized steel and mounted on protected and heavy-duty ball bearings.

Dimensions (l x w x h) [mm] 310 x 255 x 270

Model ACR192

[kg] 7.5

THREE-ROLLERS Roller for straight and slightly bended sections, suitable for cables up to Ø 150 mm. Frame made of galvanised steel, rollers of Al.

Model ACR193

Dimensions (l x w x h) [mm] 250 x 250 x 250

[kg] 5

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 120

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Cable Rollers

ACR STANDARD Made of galvanized steel and mounted on protected ball bearings, suitable for cables up to ø 120 mm. Corner rollers can be attached one to the other as to obtain different bending radius. Also available with Al rollers (model ACR194).

Dimensions (l x w x h) [mm] 550 x 340 x 370 550 x 340 x 370

Model ACR002 ACR194

Rollers dimensions (l x Ø x Ø) [mm] 190 x 110 x 76 190 x 125 x 76

Max working load [kg] 250 270

Mass

Rollers dimensions (l x Ø x Ø) [mm] 200 x 83 x 83

Max working load [kg] 400

Mass

[kg] 12 17

ADJUSTABLE Made of galvanized steel and mounted on protected ball bearings, suitable for cables up to ø 140 mm. Corner rollers can be attached one to the other as to obtain different bending radius.

Model ACR195

Dimensions (l x w x h) [mm] 370 x 330 x 420

[kg] 29

ADJUSTABLE HEAVY DUTY Specifically designed for heavy and thickcables up to ø 180 mm. Made of galvanized steel and mounted on protected ball bearings.

Max working load [kg] 500

Model ACR196

Mass [kg] 34

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 130

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Cable Guiding Devices

ACR RUN-OFF FRAME Made of galvanized steel. The rollers are mounted on protected ball bearings. It is specifically designed to guide the cable just after coming out from the drum, in order to guarantee the cable to be in the right position when being used with the next rollers. Dimensions (l x w x h) [mm] 1050 x 470 x 520

Model ACR005

Rollers dimensions (l x Ø x Ø) [mm] 620 x 40 x 40

Max working load [kg] 300

Mass [kg] 14

RUN OF FRAME (PIPES) Made of galvanized steel. The rollers are mounted on protected ball bearings.

Max pipe diameter

Model

[mm] 450 750

ACR197 ACR198

Max working load [kg] 500 1000

Mass [kg] 12 29

EDGE ROLLER Galvanized roller placed on a swivel base, suitable for cables up to ø 80 mm. Specifically designed to be used along with rims of manholes and trenches.

Model ACR095

Dimensions (l x w x h) [mm] 350 x 250 x 210

Rollers dimensions (l x Ø x Ø) [mm] 130 x 110 x 76

Max working load [kg] 100

Mass

Rollers dimensions (l x Ø x Ø) [mm] 100 x 200 x 140

Max working load [kg] 250

Mass

[kg] 6

EDGE ROLLER HEAVY DUTY Galvanized heavy-duty roller placed on a swivel base, suitable for cables up to ø 60 mm. Specifically designed to be used along with rims of manholes and trenches.

Model ACR199

Dimensions (l x w x h) [mm] 315 x 250 x 230

[kg] 18

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 140

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Cable Guiding Devices

ACR CABLE PROTECTOR BEND Made of galvanized steel, suitable for cables up to ø 60 mm. Specifically designed to protect cables along with rims of manholes and trenches.

Dimensions (l x w x h) [mm] 450 x 130 x 200

Model ACR104

Max working load [kg] 75

Mass [kg] 2

GUIDE ROLLERS Made of galvanized steel, suitable for cables up to ø 120 mm. Three rollers assembled on protected ball bearings. Specifically designed to be used along with the rims of manhole and trench. Also available with Al rollers (model ACR200).

Dimensions (l x w x h) [mm] 550 x 220 x 400 500 x 220 x 400

Model ACR004 ACR200

Rollers dimensions (l x Ø x Ø) [mm] 190 x 110 x 76 190 x 125 x 76

Max working load [kg] 250 270

Mass [kg] 10 15

ROLLERS CHAIN Made of galvanized steel. The rollers chain is composed by 12 jointed rollers. It is specifically designed to guide the cable along bends.

Rollers dimensions (l x Ø x Ø) [mm] 180 x 32 x 32

Model ACR182

Mass [kg] 28

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 150

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Cable Guiding Devices

ACR CABLE GUIDING RUN-OFF FRAME Composed by 4 rollers mounted on a sturdy frame. Made of galvanized steel.

Model ACR075

Dimensions (l x w x h) [mm] 500 x 130 x 500

Rollers dimensions (l x Ø x Ø) [mm] 60 x 60

Max working load [kg] 200

Mass [kg] 28

SUSPENSION ROLLER Made of galvanized steel. Specifically designed to be used in open trench in order to protect already laid cables.

Model ACR077 ACR078

Dimensions For trenches width 250 - 400 mm For trenches width 400 - 600 mm

Max working load [kg] 150 150

Mass

Max working load [kg] 250 250 250 250 250 250

Mass

[kg] 6 7

CABLE ROLLER - ADJUSTABLE BOOM Made of galvanized steel, suitable for cables up to ø 80 mm. Specifically designed to be used in open trench in case there are obstacles to be avoided.

Model ACR183 ACR184 ACR071 ACR072 ACR073 ACR074

Dimensions Boom stroke 300 - 500 mm Boom stroke 500 - 800 mm Boom stroke 600 - 1000 mm Boom stroke 1000 - 1500 mm Boom stroke 1500 - 1800 mm Boom stroke 1800 - 2400 mm

[kg] 9.5 10 13 16 18 23

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 160

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Cable Guiding Devices

ACR ROLLER ENTRY TOOL Made of galvanized steel with an opening frame on head and four rollers assembled on bearings. This tool provides easy cable entry into pipe irrespective of angle and direction. Also available with double protection.

Single protection Model ACR009 ACR010 ACR011 ACR012 ACR013 ACR014 ACR201 ACR202

Double protection Model ACR203 ACR204 ACR205 ACR206 ACR207 ACR208 ACR209 ACR210

External diameter [mm] 76 90 114 133 140 152 169 196

SIMPLE / BENT CABLE ENTRY TOOL Made of galvanized steel. Specifically designed to protect the cable in presence of sharp edges.

External diameter [mm] 76 90 114 140

Model ACR015 ACR016 ACR017 ACR019

End shape streight streight streight streight

Model ACR021 ACR022 ACR023 ACR151

External diameter [mm] 76 90 114 140

End shape bent bent bent bent

FLEXIBLE HOSE Specifically designed for cable laying in manholes, when job is thwarted by other cables. External diameter [mm] 90 110 115 150

Model ACR155 ACR211 ACR156 ACR212

Length [m] 3 3 3 3

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 170

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Cable Guiding Devices

ACR SHORT AND LONG RADIUS CABLE ENTRY TOOL Made of galvanized steel with three (R=420 mm) or four (R=1000 mm) rollers assembled on protected ball bearings and entry device for pipes. Particularly suitable to connect cable’s change of directions inside manholes.

Bending radius [mm] 420 420 420 420 420 420 420 1000 1000 1000 1000 1000 1000 1000

Model ACR082 ACR083 ACR084 ACR213 ACR214 ACR215 ACR216 ACR086 ACR087 ACR088 ACR217 ACR218 ACR219 ACR220

External diameter [mm] 76 90 114 133 152 169 196 76 90 114 133 152 169 196

SPARE DEVICE FOR CABLE ENTRY TOOL Made of galvanized steel.

External diameter [mm] 76 90 114 133 152 169 196

Model ACR090 ACR091 ACR092 ACR221 ACR222 ACR223 ACR224

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 180

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Fiberglass Rods

ACV Rod diameter 4.5, 6, 9 and 11 mm, made with a central part in fibreglass and an external abrasion-proof coating. It is supplied wound up on galvanized steel vertical reel frame. It comes complete with starting/ending threaded end and with a starting spinner (with hole for 4.5 and 6 mm, with shackle for 9 and 11 mm).

Model ACV225 ACV226 ACV227 ACV228 ACV229 ACV230 ACV231 ACV232 ACV233 ACV234 ACV235 ACV236 ACV131 ACV237 ACV238 ACV239 ACV240 ACV241 ACV026

Diameter [mm] 4.5 4.5 4.5 4.5 4.5 4.5 4.5 6 6 6 6 6 6 6 6 6 6 6 6

Length [m] 20 30 40 50 60 70 80 30 40 50 60 70 80 30 40 50 60 70 80

Frame configuration vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical

Model ACV242 ACV243 ACV025 ACV244 ACV245 ACV246 ACV247 ACV027 ACV029 ACV030 ACV031 ACV130

Diameter [mm] 9 9 9 9 9 9 11 11 11 11 11 11

Length [m] 60 70 80 100 120 150 100 120 150 200 250 300

Frame configuration vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m. vertical, t. m.

Note: t. m. = trailer mounted

Rod diameter 6 mm made with a central part in fiberglass and an external abrasion-proof coating. It is supplied wound up on galvanized steel horizontal reel. It comes complete with starting/ending threaded end and with a starting spinner with hole.

Diameter [mm] 6 6 6 6 6 6

Model ACV248 ACV249 ACV132 ACV133 ACV250 ACV251

Length [m] 30 40 50 60 70 80

Frame configuration horizontal horizontal horizontal horizontal horizontal horizontal

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 190

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Fiberglass Rods

ACV FREE SNAKES Rod diameter 4.5, 6, 9 and 11 mm, is available also as free snakes (without reels).

Diameter [mm] 4.5 4.5 4.5 4.5 4.5 4.5 4.5 6 6 6 6 6 6

Model ACV252 ACV253 ACV254 ACV255 ACV256 ACV257 ACV258 ACV259 ACV260 ACV261 ACV262 ACV263 ACV264

Length [m] 20 30 40 50 60 70 80 30 40 50 60 70 80

Model ACV265 ACV266 ACV267 ACV268 ACV269 ACV270 ACV271 ACV272 ACV273 ACV274 ACV275 ACV276 ACV277 ACV278 ACV279

Diameter [mm] 9 9 9 9 9 9 9 9 9 11 11 11 11 11 11

Length [m] 30 40 50 60 70 80 100 120 150 100 120 150 200 250 300

REELS Made of galvanized steel.

For rod diameter [mm] 4.5 6 6 9 9 11 11

Model ACV280 ACV281 ACV282 ACV283 ACV284 ACV285 ACV286

Frame configuration vertical vertical horizontal vertical vertical, t. m. vertical, t. m. vertical, high storage capacity, t.m. Note: t. m. = trailer mounted

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 200

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Accessories for Fiberglass Rods

ACV Starting/Ending threaded junctions Model ACV287 ACV185 ACV057 ACV058

Description for rod ø 4.5 mm, thread M5 for rod ø 6 mm, thread M6 for rod ø 9 mm, thread M12 for rod ø 11 mm, thread M12

Coupling joint for rods repairing Model ACV288 ACV186 ACV055 ACV056

Description for rod ø 4.5 mm for rod ø 6 mm for rod ø 9 mm for rod ø 11 mm

Starting Spinner Model ACV289 ACV290

Description for rod ø 4.5 mm, thread M5 for rod ø 6 mm, thread M6

Starting Spinner with shackle Model ACV187 ACV052

Description for rod ø 6 mm, thread M6 for rod ø 9 and 11 mm, thread M12

Starting Roller Model ACV188 ACV054

Description for rod ø 6 mm, thread M6 for rod ø 9 and 11 mm, thread M12

Connecting Device Model ACV291 ACV051

Description for rod ø 6 mm, thread M6 for rod ø 9 and 11 mm, thread M12

Catch Hooks Model ACV189 ACV190 ACV180

Description thread M12, pipe ø 80-100 mm thread M12, pipe ø 100-120 mm thread M12, pipe ø 125-200 mm

Glue for repairing fiberglass rods Model ACV292

Description glue, 150 gr

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 210

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Pulling Eyes

CX PULLING EYES FOR PIPES Reusable power pulling eyes, fixed head specifically designed to pull pipes.

Model CX08913400 CX08913320 CX08913410 CX08913411 CX08913322 CX08913412

Pipe diameter [mm] 18-22 24-27 27-37 35-43 43-46 49-54

Nominal size [in] 0.75 1 1.25 1.5 1.75 2

Max O.D. [mm] 32 31 44 51 57 62

Hole Ø

Eye Ø

[mm] 6 6 11 11 10 11

[mm] 13 13 13 13 13 13

Eye Thickness [mm] 10 6 13 13 13 13

PULLING EYES FOR PE & PVC PIPES Reusable power pulling eyes, fixed head specifically designed to pull PE & PVC pipes.

Model CX08220020 CX08220030 CX08220611 CX08220050 CX08220060

Nominal size [in] 2 3 4 5 6

Pipe diameter [mm] 48-55 68-79 89-106 108-129 129-152

Length

Lead cone O.D

[mm] 206 302 358 469 498

[mm] 60 89 122 141 168

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 220

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Reusable Pulling Eyes

CX STANDARD HEAD Standard head power pulling eyes are specifically to be used when pulling multiple cables. Each standard head power pulling eye includes an eye socket, sleeve nut and plug. Model CX08917220 CX08917120 CX08917820 CX08917920 CX08917720 CX08918020 CX08918120

Cable size

Max conductor Ø

[kcmil] 750 1000 1250 1500 1750 2000 2500

[mm] 25 29 33 36 39 41 46

Max eye O.D [mm] 44 52 57 60 63 64 76

Hole Ø D [mm] 15 25 25 25 25 25 25

Eye thickness T [mm] 11 13 13 13 13 13 13

CLEVIS HEAD Clevis head power pulling eyes are specifically to be used when pulling multiple cables. Each clevis head power pulling eye includes a clevis socket, sleeve nut and plug. Model

Cable size [kcmil] 750 1000 1250 1500 1750 2000 2500

CX08917250 CX08917150 CX08917850 CX08917950 CX08917750 CX08918050 CX08918150

Max conductor Ø [mm] 25 29 33 36 39 41 46

Max eye O.D A [mm] 44 52 57 60 64 64 76

Slot width B [mm] 16 19 19 19 25 25 25

Slot depth C [mm] 40 45 45 45 71 71 71

Pin Ø D [mm] 14 16 16 16 22 22 22

Pin center E [mm] 20 18 18 18 31 31 31

Max eye O.D A [mm] 44 52 57 60 64 64 76

Slot width B [mm] 16 19 19 19 25 25 25

Slot depth C [mm] 40 45 45 45 71 71 71

Pin Ø D [mm] 14 16 16 16 22 22 22

Pin center E [mm] 20 18 18 18 31 31 31

SWIVEL HEAD The swivel head power pulling eye is a hyped tool that combines features from standard reusable with pulling eyes and swivels. It eliminates the need for different separate swivel on each pulling eye when installing single cables. Each swivel head power pulling eye includes a swivel head, sleeve nut and plug. Model CX08917275 CX08917175 CX08917875 CX08917975 CX08917775 CX08918075 CX08918175

Cable size [kcmil] 750 1000 1250 1500 1750 2000 2500

Max conductor Ø [mm] 25 29 33 30 39 41 46

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 230

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Head Type Sock Joints

GCL-GCT Specifically designed to temporally connect the cable to the pulling rope. They consist of steel wire which effectively distribute the grip effect on the cable.

Head type sock joint with 1 Loop-Long Mod. GCL Model GCL110 GCL120 GCL130 GCL140 GCL150 GCL160 GCL170 GCL180 GCL190 GCL200 GCL210 GCL220 GCL230 GCL221 GCL231

Cable Ø [mm] 10-14 15-20 21-25 26-30 26-45 31-40 41-50 46-60 61-80 81-100 101-140 141-170 171-200 150-180 180-210

Net length [mm] 900 900 1000 1200 1500 1500 1500 1600 1800 2000 2000 2000 2000 2000 2000

Breaking load [kN] 20 20 25 30 50 45 50 50 80 100 100 100 100 200 200

Suitable swivel

Net length [mm] 600 600 600 600 700 700 800 800 800 1000 1200 1200 1200

Breaking load [kN] 20 20 25 30 45 50 50 50 80 100 100 100 100

Suitable swivel

GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT010 GGT010 GGT010 GGT010 GGT020 GGT020

Head type sock joint with 1 Loop-Short Mod. GCT Model GCT380 GCT390 GCT400 GCT410 GCT420 GCT430 GCT440 GCT450 GCT460 GCT470 GCT480 GCT490 GCT495

Cable Ø [mm] 11-14 15-20 21-25 26-30 31-40 26-45 41-50 46-60 61-80 81-100 101-140 141-170 171-200

GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT010 GGT010 GGT010 GGT010

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 240

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Sock Joints

GCP/GCA-GCS Specifically designed to temporally connect the cable to the pulling rope. They consist of steel wire which effectively distribute the grip effect on the cable. Also available in open version.

Sock joint with 2 loops Mod. GCP/GCA Model Passing GCP241 GCP252 GCP262 GCP271 GCP281 GCP292 GCP301 GCP311 GCP326 GCP332 GCP341 GCP351 GCP361

Cable Ø [mm] 10-14 15-20 21-25 26-30 26-45 31-40 41-50 46-60 61-80 81-100 101-140 141-170 171-200

Open GCA240 GCA250 GCA260 GCA270 GCA280 GCA290 GCA300 GCA310 GCA320 GCA330 GCA340 GCA350 GCA360

Net length [mm] 800 800 800 800 1000 1000 1000 1000 1000 1200 1400 1400 1400

Breaking load [kN] 20 20 25 30 50 50 50 50 80 100 100 100 100

Suitable swivel GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001 GGT001

Specifically designed to temporally connect two lengths of cable. They consist of steel wire which effectively distribute the grip effect on the cable.

Double head type sock joint Mod. GCS Cable Ø [mm] 11-14 15-20 21-25 26-30 26-45 31-40 41-50 46-60 61-80 81-100 101-140 141-170 171-200 150-180 180-210

Model GCS620 GCS630 GCS640 GCS650 GCS660 GCS670 GCS680 GCS690 GCS700 GCS710 GCS720 GCS730 GCS740 GCS731 GCS741

Net length [mm] 1200 1200 1200 1200 1400 1400 1600 1600 1600 2000 2400 2400 2400 4000 4000

Breaking load [kN] 20 20 25 30 50 45 50 50 80 100 100 100 100 200 200

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 250

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


Connecting Devices

GGT-ALG SWIVEL JOINTS - GGT The swivel joints are suitable to connect the pulling rope to the mesh sock joint mounted on the conductor; they are mounted on thrust bearings and they are designed to avoid torsion strain accumulation. They are made of highly tensile galvanized steel; the special design can bear the high radial loads, which occur during the passage over the pulleys.

Dimensions [mm]

Model

A

GGT001 GGT010 GGT020

B C

A 106 143 184

B 28 40 54

C max 10 13 18

Pin type 209

Breaking load [kN] 70 110 220

Mass [kg] 0.3 0.925 2.15

Bolt type 2130

SHACKLES - ALG Screw pin anchor shackles meet the requirement of Federal Specification RR-C271D type IVA, Grade A, Class 2. Bolt type anchor shackles with head bolt-nut with cotter pin meet the requirement of Federal Specification RR-C-271D type IVA, Grade A, Class 3. Dimensions [mm] Model ALG050 ALG051 ALG052 ALG053 ALG054 ALG055 ALG056 ALG057 ALG058 ALG059 ALG060 ALG061 ALG062 ALG063 ALG064 ALG065

Al AIB working load limit

Nominal shakle size

[kN]

[in]

5 7.5 10 15 20 32.5 47.5 65 85 15 32.5 47.5 65 85 120 135

1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1 7/16 5/8 3/4 7/8 1 1 1/4 1 3/8

Inside length 28.6 31 36.5 42.8 47.6 60 71 84 95 42.8 60 71 84 95 119 132

Inside width

Tolerance plus of minus

Diameter

At pin

At bow

At pin

12.7 13.5 16.7 18.3 20.6 27 31.8 36.5 42.9 18.3 27 31.8 36.5 42.9 52 57

19.8 21.4 26.2 29.4 33.3 42.9 51 58 68 29.4 42.9 51 58 68 83 89

7.94 9.53 11.1 12.7 15.9 19.1 22.2 25.4 28.6 12.7 19.1 22.2 25.4 28.6 34.9 38.1

Outside of eye 17.5 20.6 24.7 27 30.2 39.7 47.6 54 60 27 39.7 47.6 54 60 76 84

Length

Width

1.59 1.59 3.18 3.18 3.18 3.18 6.35 6.35 6.35 3.18 3.18 6.35 6.35 6.35 6.35 6.35

1.59 1.59 1.59 1.59 1.59 1.59 1.59 1.59 1.59 1.59 1.59 1.59 1.59 1.59 1.59 3.18

Mass [kg] Screw pin Bolt type type 209 2130 0.05 0.08 0.14 0.20 0.29 0.60 1.05 1.54 2.35 0.36 0.73 1.23 1.79 3.75 5.31 7.18

&HUWL¿HG«4XDOLW\«6\VWHP

ISO 9001:2008 Keep you updated on:

Tesmec S.p.A.

www.tesmec.com

Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445 Ed. 2012/06

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562

U 260

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE


www.tesmec.com

Watch the video of the machines in action on your Smartphone

Tesmec S.p.A. Headquarters Via Zanica, 17/O - 24050 Grassobbio (BG) - Italy Tel: +39.035.4232911 - Fax: +39.035.4522445

Manufacturing facilities Via Pertegalli, 2 - 24060 Endine Gaiano (BG) - Italy Tel: +39.035.825024 - Fax: +39.035.826375

Manufacturing facilities Via Don Brambilla, 26/28 - 23844 Sirone (LC) - Italy Tel: +39.031.858311 - Fax: +39.031.853562


Underground catalogue 2012  

Underground catalogue 2012 - Equipment for laying underground cables

Read more
Read more
Similar to
Popular now
Just for you