281059158 790 system planning ver 2 6 120413

Addendum Provider 790 Nurse Call System System Planning Guide Version 2.6- 12/04/13

The current version includes the following updates:

•

Pg. 6-11: Update maximum cable length in 796x Console Controller table to 700 ft. between Controller and Nurse Console/Terminal.

Jeron Electronic Systems, Inc. 1743-55 W. Rosehill Drive Chicago, IL 60660 (773) 275-1900 U.S.A. & Canada: (800) 621-1903 Fax: (773) 275-0283 www.jeron.com

.

ProviderÂŽ 790 Nurse Call System System Planning Guide Version 2.6 - 12/04/13

Jeron Electronic Systems, Inc. 1743-55 W. Rosehill Drive Chicago, IL 60660 (773) 275-1900 U.S.A. & Canada: (800) 621-1903 Fax: (773) 275-0283 www.jeron.com

.

Proprietary Information The information contained herein is the proprietary property of Jeron Electronic Systems, Inc. Recipient, by accepting this information agrees that neither this document nor the information contained herein shall be reproduced or transferred to other documents or disclosed to others for manufacturing or any other purpose except as authorized in writing

by Jeron Electronic Systems, Inc.

About this Manual This document is based on information available at the time of its writing. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, or to provide for every possible contingency in connection with installation, operation, or maintenance. Jeron Electronic Systems, Inc. assumes no obligation of notice to holders of this document with respect to changes subsequently made.

Jeron Electronic Systems, Inc. makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

Copyright Information All information resident in this document is considered copyrighted.

The Jeron products described in this instruction manual may include copyrighted Jeron computer programs stored in semiconductor memories or other mediums. Laws in the United States and foreign countries preserve for Jeron certain exclusive rights to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Jeron computer programs contained in the Jeron products described in this instruction manual may not be copied or reproduced in any manner without the express written permission of Jeron Electronic Systems, Inc. Furthermore, the purchase of Jeron products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Jeron, except for the normal non-exclusive, royalty free license to use that arises by operation of law in the sale of a product.

JERONŽ is a registered trademark of Jeron Electronic Systems, Inc. Š 2013 by Jeron Electronic Systems, Inc., All Rights Reserved

Š 2013 Jeron Electronic Systems Inc.

i

Provider 790 Nurse Call System

.

ii

Š 2013 Jeron Electronic Systems Inc.

Contents Chapter 1: System Architecture Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 In this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Jeron IP Network & Facility LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

System Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Jeron Nurse Call Buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

J Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

R Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

P Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

M Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Single Gateway J Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Single Nurse Call Isolated 8 Port Ethernet Switch. . . . . . . . . . . . . . . . . . . .

Multiple Nurse Call Isolated 8 Port Ethernet Switch . . . . . . . . . . . . . . . . . .

Room Controllers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Console (Master) Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3 1-4 1-4 1-4 1-4 1-4 1-4 1-5 1-5 1-5 1-5 1-5 1-5 1-5

System Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Audio Visual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Audio Visual with Integrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Tone Visual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Chapter 2: Equipment Closet Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Gateways. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Model 7992/93 Nurse Call Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Model 7995 Power Supply with Battery Backup . . . . . . . . . . . . . . . . . . . . . 2-5

Connecting Gateway & Power Supply . . . . . . . . . . . . . . . . . . . . . . . 2-6 Power Supply Requirements Per Gateway. . . . . . . . . . . . . . . . . . . . . . . . . .

By Number of J Bus Devices (Prism Dome Lights) . . . . . . . . . . . . . . . . . . .

For 7967-P Terminal Intercom Operation Only (No Dome Lights) . . . . . . .

Multiple Power Supplies on One Gateway . . . . . . . . . . . . . . . . . . . . . . . . .

Supplemental Power Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 3: Hallways

2-6 2-6 2-6 2-7 2-8

Hallway J Bus Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Room Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Š 2013 Jeron Electronic Systems Inc.

1

Model 7950 Room Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7951 Room Controller and Two Color Dome Lights . . . . . . . . . . . . .

Model 7952 Room Controller and Six Color Dome Lights . . . . . . . . . . . . . .

Associated Equipment for Room Controllers . . . . . . . . . . . . . . . . . . . . . . .

Console Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7960 Console Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7961 Console Controller and Two Color Zone Light. . . . . . . . . . . . .

Model 7962 Console Controller and Six Color Zone Light. . . . . . . . . . . . . .

Model 7963 Console Controller and Prism Zone Light . . . . . . . . . . . . . . . .

Associated Equipment for Console Controllers . . . . . . . . . . . . . . . . . . . . .

Zone Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7971 Two Color Zone Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7972 Six Color Zone Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7973 Prism Zone Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Associated Equipment for Zone Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 4: Patient Rooms & Staff Stations

3-2 3-2 3-2 3-4 3-5 3-5 3-5 3-5 3-6 3-6 3-7 3-7 3-7 3-8 3-8

Overview of Patient Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Audio R Bus Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Patient Room Audio Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Private Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Semi-Private Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Ward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Associated Equipment for Patient Stations . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Customizable Button Labels on Audio Stations. . . . . . . . . . . . . . . . . . . . . . 4-8 Relays on Patient Stations for Light Controllers . . . . . . . . . . . . . . . . . . . . . 4-9 Staff Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Model 7912 Staff Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Model 7916 PA Page Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Model 7917 Visual Duty Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Model 7927 Staff/Duty Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Associated Equipment for Staff Audio Stations . . . . . . . . . . . . . . . . . . . . . 4-13 Patient & Facility Bathrooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Model 7919 Pullcord & Pushbutton Bath Station (with Audio). . . . . . . . . . 4-14 Associated Equipment for Bath Stations . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Utility Rooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Model 7918 Electrical Supervision Station . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Peripheral P Bus Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Patient Rooms & Staff Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Model 7934 Staff Presence Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Model 7937 Remote Cancel Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Model 7940 Procedure, Presence, and Bed Management Station . . . . . . 4-20 Associated Equipment for Staff Presence & Procedure, Presence, and Bed Management Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 Model 7941 Dual Auxiliary Alarm Input Station . . . . . . . . . . . . . . . . . . . . . 4-21 Model 7945 Dual External Alarm Input Station . . . . . . . . . . . . . . . . . . . . . 4-22

2

Š 2013 Jeron Electronic Systems Inc.

Associated Equipment for Auxiliary Input Stations . . . . . . . . . . . . . . . . . . 4-22 Model 7947 8 Input Bed Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 Patient or Facility Bathroom & Shower. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24 Model 7932 Pullcord & Pushbutton Station . . . . . . . . . . . . . . . . . . . . . . . . 4-24 Model 7958 Shower Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25 -R Relay Option for 7932 Pullcord & Pushbutton Station or 7958 Shower Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25 Associated Equipment for Pullcord & Pushbutton Station & Shower Station4-25 Other Facility Rooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 Model 7930 Single Pushbutton Station . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 Model 7931/7931-P Dual Pushbutton Station . . . . . . . . . . . . . . . . . . . . . . 4-27 Model 7949/7949-P Code Blue/Code Pink Station . . . . . . . . . . . . . . . . . . 4-28 -R Relay Option for 7931 and 7949 Stations . . . . . . . . . . . . . . . . . . . . . . . 4-28 Peripheral Station Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Customizable Call Button Labels on Peripheral Stations . . . . . . . . . . . . . 4-29 Call Types & Indications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

Patient Room Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 Pillow Speakers for DIN Jack Patient Stations. . . . . . . . . . . . . . . . . . . . . .

Model 7901 Standard Pillow Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7902 Standard Pillow Speaker with Two Aux Buttons . . . . . . . . . .

Model 7903 Direct Access Pillow Speaker . . . . . . . . . . . . . . . . . . . . . . . .

Model 7904 Direct Access Pillow Speaker with Two Aux Buttons. . . . . . .

Model 7905 Enhanced Pillow Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . .

Associated Equipment for Pillow Speakers . . . . . . . . . . . . . . . . . . . . . . . .

Model 7906 Pillow Speaker Auxiliary Output Module . . . . . . . . . . . . . . . .

Callcord(s) for DIN Jack Patient Stations . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7908 Sealed Callcord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7909/7910 Callcord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7913 Callcord Adapter, 1/4”-to-DIN . . . . . . . . . . . . . . . . . . . . . . . .

Model 7914 Geriatric Callcord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 8839 Breath Activated Callcord . . . . . . . . . . . . . . . . . . . . . . . . . . .

Associated Equipment for Callcords . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 5: Consoles & Terminals

4-34 4-34 4-35 4-36 4-37 4-38 4-39 4-39 4-40 4-40 4-40 4-41 4-41 4-41 4-42

Call Center M Bus Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Model 7965 Color Touchscreen Nurse Console. . . . . . . . . . . . . . . . . . . . . .

Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Associated Equipment for Nurse Consoles . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7967-P Color Touchscreen Workflow Terminal in Patient Rooms .

Associated Equipment for Workflow Terminal . . . . . . . . . . . . . . . . . . . . . . .

Model 7967-S Color Touchscreen Staff Duty Terminals in Staff Areas . . .

Associated Equipment for Staff Duty Terminal . . . . . . . . . . . . . . . . . . . . . .

Model 7967-M Color Touchscreen Nurse Terminals in Staff Areas . . . . . .

Associated Equipment for Nurse Terminal . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 6: System Wiring © 2013 Jeron Electronic Systems Inc.

5-1 5-2 5-3 5-3 5-4 5-5 5-6 5-6 5-7

3

Installation and Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Equipment Protection Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation Precautions for Patient and Staff Safety. . . . . . . . . . . . . . . . . .

Planning System Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wiring Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Bus Types & Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cat-5/6 Cable Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-1 6-1 6-2 6-2 6-2 6-3

790 System Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Typical Floor Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

790 Floor Wiring with 7967-P Workflow Terminals for Individual Patient Rooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Patient Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Staff Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nurse Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Additional Hallway Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4 6-5 6-6 6-8 6-9 6-9

Cable Requirements & Distances . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Central Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gateways. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nurse Call Isolated 8 Port Ethernet Switch with Uplink Port . . . . . . . . . . .

Power Supply with Battery Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Controllers (J Bus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Console Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Room Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Standard/Prism Zone Light Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . .

Room Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

R Bus Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

P Bus Stations (Peripherals) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nurse Consoles & Terminals (M Bus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nurse Console & Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 7: Device Installation

6-10 6-10 6-10 6-11 6-11 6-11 6-11 6-11 6-12 6-12 6-12 6-12 6-12

Backboxes, Mounting Racks & Wall Cabinets . . . . . . . . . . . . . . . . 7-1 Backboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Jeron Mounting Kits & Wall Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 9840 Rack Mount Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 9842 Rack Mount Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7988/7989 Wall Mount Cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wall Cabinet Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Jeron Wall Mounting Bracket for Consoles & Terminals . . . . . . . . . . . . . .

7-1 7-3 7-3 7-3 7-5 7-7 7-9

Chapter 8: Networking, Programming and Integrations

Network Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Isolated 8 Port Ethernet Switch (with Fiber Uplink Option) . . . . . . 8-1 Model 7991. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Model 7991-FX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Associated Equipment for Isolated 8 Port Ethernet Switch . . . . . . . . . . . . . 8-3 4

Š 2013 Jeron Electronic Systems Inc.

Gateway connection to Switch in Five-floor Facility . . . . . . . . . . . . . . . . . . 8-3 Interconnected Switches and Connected Gateways . . . . . . . . . . . . . . . . . . 8-4

Bridge PC and the Jeron IP Network . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Bridge PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Minimum PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

For systems 150 beds or less:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Minimum PC Requirements ( 151+ Beds) . . . . . . . . . . . . . . . . . . . . . . . . . . .

For 151 to 500 beds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

For 501 to 1500 beds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

For 1500+ beds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-5 8-6 8-6 8-6 8-7 8-8 8-8

Required Software Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Model 7984 Bridge Software Application . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Model 7990 Administration Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Programming System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Optional Software Integrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Bridge PC System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Minimum Client PC Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7970 Automatic Voice Prompt Software . . . . . . . . . . . . . . . . . . . . .

Model 7977 ADT Patient Information Integration Software. . . . . . . . . . . .

Model 7978SIP SIP Phone Integration Software . . . . . . . . . . . . . . . . . . . .

Model 7980 Staff Assignment & Messaging Software. . . . . . . . . . . . . . . .

Model 7981 RTLS Integration Software. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7983 EIS Log Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7985 PC Console Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 7986 Map Configuration Software . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 6894 Integration Data Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Š 2013 Jeron Electronic Systems Inc.

8-12 8-12 8-13 8-13 8-13 8-14 8-14 8-15 8-15 8-15 8-16

5

6

© 2013 Jeron Electronic Systems Inc.

Figures Chapter 1: System Architecture Figure 1.1:Provider 790 System Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Figure 1.2:System Planning Sketch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Chapter 2: Equipment Closet

Figure 2.1:Equipment Closet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 2.2:Model 7993 Nurse Call Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 2.3:Model 7995 Power Supply with Battery Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 2.4:Wiring Power Supply to Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 2.5:Wiring with Gateway Diagnostic Splitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 2.6:Power Splitter Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 3: Hallways

2-1 2-3 2-5 2-6 2-7 2-9

Figure 3.1:Room Controllers (L-R): Model 7950, Model 7951/5253 . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Figure 3.2:Console Controllers (L-R): Model 7960, Model 7961/62/63 . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Figure 3.3:Zone Controller Model 7971/72/73. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Chapter 4: Patient Rooms & Staff Stations

Figure 4.1:Model 7923 Enhanced Patient Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Figure 4.2:Model 7925 Single Patient Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Figure 4.3:Model 7924 Enhanced Dual Patient Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Figure 4.4:Model 7926 Dual Patient Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Figure 4.5:Model 7912 Staff Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Figure 4.6:Model 7916 PA Page Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Figure 4.7:7916 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Figure 4.8:Model 7917 Visual Duty Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Figure 4.9:7917 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Figure 4.10:Model 7927 Staff/Duty Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Figure 4.11:Model 7919 Pullcord & Pushbutton Bath Station w/Audio . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Figure 4.12:Model 7918 Electrical Supervision Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Figure 4.13:Model 7934 Staff Presence Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Figure 4.14:Model 7937 Remote Cancel Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Figure 4.15:Model 7940 Procedure, Presence, and Bed Management Station . . . . . . . . . . . . . . . . . 4-20 Figure 4.16:Model 7941 Dual Auxiliary Alarm Input Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Figure 4.17:Model 7945 Dual External Alarm Input Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Figure 4.18:Model 7947 8 Input Bed Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 Figure 4.19:7947 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 Figure 4.20:Model 7932 Pullcord & Pushbutton Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24 Figure 4.21:Model 7958 Shower Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25 Figure 4.22:Model 7930 Single Pushbutton Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 Figure 4.23:Model 7931/7931-P Dual Pushbutton Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 Figure 4.24:Model 7949/7949-P Code Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28 Figure 4.25: Peripheral Stations with Customizable Button Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Figure 4.26:Model 7901 Standard Pillow Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 Figure 4.27:Model 7902 Standard Pillow Speaker with Two Auxiliary Buttons . . . . . . . . . . . . . . . . . . 4-35 Figure 4.28:Model 7903 Direct Access Pillow Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36 Figure 4.29:Model 7904 Direct Access Pillow Speaker with Two Auxiliary Buttons . . . . . . . . . . . . . . 4-37 Figure 4.30:Model 7905 Enhanced Pillow Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38 Figure 4.31:7905 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38 Figure 4.32:Model 7906 Pillow Speaker Auxiliary Output Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39 Figure 4.33:Model 7908 Sealed Callcord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40

Š 2013 Jeron Electronic Systems Inc.

7

Figure 4.34:Model 7909/7910 Callcord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4.35:Model 7913 Callcord Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4.36:Model 7914 Geriatric Callcord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4.37:Breath Activated Call Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 5: Consoles & Terminals

4-40 4-41 4-41 4-42

Figure 5.1:Model 7965 Nurse Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5.2:7965 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5.3:Workflow Terminal (Model 7967-P) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5.4:Staff Duty Terminal (Model 7967-S). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5.5:7967-S Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5.6:Nurse Terminal (Model 7967-M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5.7:7967-M Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2 5-3 5-4 5-5 5-6 5-7 5-7

Figure 6.1:Typical Floor Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6.2:Alternate Floor Wiring Scenario with Touchscreen Workflow Terminals . . . . . . . . . . . . . . .

Figure 6.3:Typical Room Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6.4:Typical Staff Lounge Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6.5:Typical Nurse Station Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4 6-5 6-6 6-8 6-9

Figure 7.1:9840 Rack with Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.2:9842 Rack with 7991 Isolated 8 Port Ethernet Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.3:Gateway and Switch Mounted on 19� Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.4:790 Rack Mounting Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.5:Wall Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.6:7988 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.7:7989 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.8:Model 7988 Equipment Assembly Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.9:Model 7989 Equipment Assembly Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7.10:Wall Mounting Bracket Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-3 7-3 7-4 7-4 7-5 7-6 7-6 7-8 7-8 7-9

Chapter 6: System Wiring

Chapter 7: Device Installation

Chapter 8: Networking, Programming and Integrations Figure 8.1:Isolated 8 Port Ethernet Switch Model 7991 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Figure 8.2:Fiber Uplink Option on Model 7991-FX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Figure 8.3:Gateway Connections to an Isolated 8 Port Ethernet Switch in a Five-Floor Facility. . . . . . 8-3 Figure 8.4:Isolated Switches and their Connected Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Figure 8.5:Provider 790 Computer Integrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Figure 8.6:Dual Server Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Figure 8.7:Units, Rooms and Coverage Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11

8

Š 2013 Jeron Electronic Systems Inc.

Tables Chapter 2: Equipment Closet Table 2.1:7992/92 Gateway Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2.2:Associated Equipment for Gateways. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2.3:7995 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2.4:7995 Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2.5:Power Supply Requirements on J Bus w/ Dome Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2.6:Power Supply Requirement for Workflow Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2.7:Capacity for One Gateway with Multiple Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-3 2-4 2-5 2-5 2-6 2-6 2-8

Table 3.1:7950 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.2:7951 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.3:7952 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.4:7953 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.5:Room Controllers Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.6:7960 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.7:7961 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.8:7962 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.9:7963 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.10:Console Controllers Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.11:7971 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.12:7972 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.13:7973 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 3.14:Zone Lights Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2 3-2 3-3 3-3 3-4 3-5 3-5 3-6 3-6 3-6 3-7 3-7 3-8 3-8

Chapter 3: Hallways

Chapter 4: Patient Rooms & Staff Stations

Table 4.1:7923 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Table 4.2:7925 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Table 4.3:7924 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Table 4.4:7926 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Table 4.5:Associated Equipment for Patient Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Table 4.6: Audio Stations with Customizable Button Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Table 4.7:7912 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Table 4.8:Associated Equipment for PA Page Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Table 4.9:7927 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Table 4.10:Associated Equipment for Staff Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Table 4.11:7919 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Table 4.12:Associated Equipment for Bath Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Table 4.13:7918 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Table 4.14:Associated Equipment for Electrical Supervision Stations . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Table 4.15:7934 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Table 4.16:7937 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Table 4.17:7937 Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Table 4.18:7940 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 Table 4.19:7934 & 7940 Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 Table 4.20:7941 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Table 4.21:7945 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Table 4.22:7941 & 7945 Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Table 4.23:7932 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24 Table 4.24:Model 7958 Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25 Table 4.25:7932/7958 Associated Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

© 2013 Jeron Electronic Systems Inc.

9

Table 4.26:7930 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.27:7931/7931-P Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.28:7949/7949-P Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.29:7949/7949-P Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.30:7901 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.31:7902 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.32:7903 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.33:7904 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.34:Pillow Speakers Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.35:7906 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.36:7908 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.37: 7909/7910 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.38:7913 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.39:7914 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.40:8839 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4.41:Callcord Associated Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 5: Consoles & Terminals

4-26 4-27 4-28 4-28 4-34 4-35 4-36 4-37 4-39 4-39 4-40 4-40 4-41 4-41 4-42 4-42

Table 5.1:7965 Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 5.2:7967-P Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 5.3:7967-P Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 5.4:7967-S Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 5.5:7967-M Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 7: Device Installation

5-3 5-4 5-4 5-5 5-7

Table 7.1:Jeron Rack Mount Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Table 7.2:7988/7989 Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Table 7.3:Wall Cabinet Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

Chapter 8: Networking, Programming and Integrations Table 8.1:7991 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Table 8.2:Equipment for Isolated 8 Port Ethernet Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Table 8.3:Provider 790 Capacity & Number of PCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

10

© 2013 Jeron Electronic Systems Inc.

Chapter 1: System Architecture

.

System Planning

Introduction

Introduction The Jeron Provider® 790 Nurse Call System is an advanced, highly programmable and flexible system for signaling and voice communication between patients and staff in hospitals and nursing homes.

In this Manual This System Planning manual presents information about system components, wiring, and programming, organized by typical facility location and order of installation, as follows: •

Equipment or utility closet: provides a list of equipment that is typically installed in standard 19" racks or cabinets for the purposes of corridor, patient room, and staff area planning: Gateways, Power Supplies and interfaces. Isolated 8 Port Ethernet Switches, also installed in utility closets, will be discussed as part of the networking process

•

Hallways (corridor): provides information on corridor Room, Console and Zone Controllers, and corridor lights

•

Patient rooms and staff areas: provides information on audio and peripheral (non-audio) stations; call types and indicators; a list of equipment in bathrooms and showers, and associated or specialty equipment installed elsewhere in a facility (such as staff areas)

•

Nurse station and other Console Controller devices: provides a description of the primary nurse call device, the Nurse Console, and information about the Staff Duty, Nurse and Workflow Terminals in patient rooms and staff areas

•

Wiring, device installation and safety: provides cable types, lengths and distances; station dimensions and recommended backboxes; and important safety information necessary to plan system installation

•

Networking, programming and software integrations: provides an overview of the Jeron IP Networking with the Isolated 8 Port Ethernet Switch, requisite programming, and a list of applications that may be integrated to the 790 nurse call system and the required equipment

Capabilities The Provider 790 system offers the following capabilities: •

Eight simultaneous full-duplex local digital audio paths per Gateway

•

Scalable system that supports over 3,900 rooms (Controllers)

•

Cat-5/5e/6 cable for audio stations for simplified wiring and service.

Peripheral stations use single pair wires

•

Configurable buttons and button labels on audio and peripheral stations

•

Color touchscreen Nurse Console and four tactile buttons for the most common features/navigation

•

Flexible programming using a PC

© 2013 Jeron Electronic Systems Inc.

1-1

Introduction

System Planning

Jeron IP Network & Facility LAN The backbone of the Provider system is the Jeron IP Network. The networked nurse call architecture supports flexible room coverage and call routing throughout the entire facility. Optional integrations provide added functionality to staff members, including EIS report generation or real-time display of system call activity on client PCs on the facility LAN. The system can also interface with popular third-party devices and equipment, including: •

Admission-Discharge-Transfer (ADT) application to map HL7 fields to Provider 790 for display on consoles or terminals

•

RTLS badges for automatic registration of staff in and out of rooms

•

Wireless SIP handsets for direct call routing of patient calls to assigned caregiver

•

Pocket pagers for staff member notification of patient calls

Refer to See “Optional Software Integrations” on page 8-12 for a complete list of available applications.

1-2

© 2013 Jeron Electronic Systems Inc.

System Planning

System Architecture

System Architecture Overview

Figure 1.1: Provider 790 System Architecture The Provider system architecture scheme begins at the equipment closet.

Gateways and Isolated 8 Port Ethernet Switches are typically located near a line power source, either mounted on standard 19� racks or enclosed in Jeron wall cabinets. The Gateway distributes power, data, and digital audio to corridor controllers and their stations. Both products are powered by the Jeron Power Supply with Battery Backup, similarly mounted. Gateways and Switches are housed in aluminum enclosures.

Extending from the equipment closet out to facility patient and staff areas, components are organized along four local buses. These buses ensure standardized cabling, minimal wiring, and life safety operation with the continuous supervision of all devices. The corridor bus connects the Gateway to all Room/Console/Zone Controllers in a continuous run with Cat 6 cable.

Stations in a room connect in series to a Room Controller located above the entrance to a room in the hallway.

Controllers drive and supervise the stations connected to them and provide regulated power and data (and audio to audio stations). When a controller is equipped with corridor lights, the lights provide visual call signals for calls placed from the stations in the room connected to it.

Š 2013 Jeron Electronic Systems Inc.

1-3

System Architecture

System Planning

Audio stations connect via Cat 5/5e/6 cable. Peripheral stations connect in series to a Room Controller via 22 AWG wire pair.

Zone Controllers with dome lights are located in those portions of a corridor where room dome lights may not be visible to the nurse station.

A Nurse Console, Staff Duty Terminal, Workflow Terminal, or Nurse Terminal connects to a Console Controller and serve as main hubs for nurse call activity management for attendants.

Jeron Nurse Call Buses The Provider system uses four local buses:

J Bus • • •

CAT 6 Cable (23 AWG) Corridor runs – connects Gateway to: Room, Console and Zone Controllers Refer to “Hallway J Bus Devices” on page 3-1

R Bus • • •

CAT 5 or better Cable Connects all audio stations with Room Controllers Refer to “Audio R Bus Stations” on page 4-3

P Bus • • •

Single 22 AWG unshielded, twisted pair (UTP) Connects all non-audio (peripheral) stations with Room Controllers Refer to “Peripheral P Bus Stations” on page 4-17

M Bus • • •

CAT 6 or better Cable Connects a Nurse Console or Staff Duty, Workflow, or Nurse Terminal to a Console Controller Refer to “Call Center M Bus Stations” on page 5-1

System Capacity Refer to the information below to determine the number of Gateways and Nurse Call Isolated 8 Port Ethernet Switches required.

Each Gateway is assigned a unique IP address and location name prior to connection. IP addresses must start with x.x.x.1 for the first Gateway and be continuously sequential for all subsequent Gateways.

More than one Gateway in a system require a Nurse Call Isolated 8 Port Ethernet Switch.

1-4

© 2013 Jeron Electronic Systems Inc.

System Planning

System Types

Single Gateway J Bus A combination of up to 31 Controllers (Room, Console, Zone) per Gateway is allowed.

Maximum distance between Gateway to last controller: 700 ft.

Supports up to eight (8) simultaneous full duplex audio paths.

Maximum Gateways A maximum of 127 Gateways are supported by the system for a combination of over 3900 controllers.

Single Nurse Call Isolated 8 Port Ethernet Switch A maximum of eight (8) Gateways connect to one (1) Isolated Switch for a total of 248 rooms.

Multiple Nurse Call Isolated 8 Port Ethernet Switch One system can accept a maximum of 16 Isolated Switches for Gateways, with an additional three (3) for Switch-to-Switch use. Up to eight (8) Switches are permitted between any two (2) Gateways.

Room Controllers Combined total of 15 R Bus and P Bus stations allowed on one (1) Room Controller.

Console (Master) Controller One Nurse Console, Staff Duty Terminal, Workflow Terminal or Nurse Terminal station allowed per controller.

Note: Console Controllers supporting Nurse Consoles, Staff Duty Terminals or Nurse Terminals should be limited to four (4) per Gateway when possible to ensure non-blocking audio connections.

Power Supply One Power Supply per Gateway at a minimum. Add one per each Switch that is NOT located next to a Gateway. One additional Power Supply is necessary to support between three (3) and eight (8) supplemental Console Controllers on a single Gateway; two (2) additional Power Supplies needed for nine (9) to 15 supplemental Console Controllers on a single Gateway.

System Types Audio Visual Typically installed in long term care facilities and hospitals, the audio-visual system provides full duplex two-way voice communication between patient and staff. The calling station, equipped with a microphone and speaker, allows the patient to place a call to the Nurse Console and communicate with the nurse via a pillow speaker. Depending on call type, the call may be canceled at the console or at the originating station.

Š 2013 Jeron Electronic Systems Inc.

1-5

Getting Started

System Planning

Audio Visual with Integrations Typically installed in hospitals, the audio-visual system with integrations integrates the Jeron system with Jeron applications and third-party equipment, such as: client PCs to mirror nurse call activity on the system; wireless handsets and pocket pagers to be able to send calls directly to the devices carried by staff; Executive Information System to create nurse call activity reports; ADT integration to interface the Jeron nurse call system with the facility’s Admissions, Discharge and Transfer (ADT) HL7-compliant application to automatically transmit relevant patient information; and IR Locator to locate staff members easily.

Tone Visual Typically installed in assisted living facilities, in the tone visual system call devices generate tones, light dome/zone lights in hallways and annunciate at the nurse console. No voice communication is established between patient and staff. Calls are canceled at the station that originated the call.

Getting Started While standard practices are established for both the physical locations and electrical connections of the system components, compliance with any local or state regulations that may apply to that specific application is also required.

System layouts and installation procedures should be completed and discussed with the customer well in advance of the arrival of the equipment at the site. Failure to do so may result in system installation delays.

Follow the steps below when conducting system planning:

1-6

•

Understand 790 cable requirements/limits and equipment feature capabilities as discussed herein

•

Obtain specifications, architectural/electrical drawings and/or conduct walk-thru of jobsite.

•

Compile a room-by-room material list that groups required equipment by nursing unit and floor

•

Make a single sketch showing each corridor J Bus cable run with Room, Console, and Zone Controller locations and identity. Expand this drawing with R Bus and P Bus stations for each room, according to specifications provided in this manual. Refer to Figure 1.2 for an example

© 2013 Jeron Electronic Systems Inc.

System Planning

Getting Started

.

Figure 1.2: System Planning Sketch

Š 2013 Jeron Electronic Systems Inc.

1-7

Getting Started

1-8

System Planning

Š 2013 Jeron Electronic Systems Inc.

Chapter 2: Equipment Closet

. .

System Planning

Overview

Overview

Figure 2.1: Equipment Closet The equipment closet houses, at a minimum, the Gateway, Power Supply and Switch (all shown). The Jeron Model 7992/93 Nurse Call Gateway is used as the local control for data and audio, and the configuration hub for up to 31 of any combination of Room, Console or Zone Controllers; 1) up to eight (8) Console Controllers that support a Nurse Console/Staff Duty Terminal/Nurse Terminal, or 2) up to 14 Controllers with Workflow Terminals plus one Controller with Nurse Console, may be connected to a single Gateway.

Gateways must be programmed with a unique IP address and location name prior to wiring on the J Bus. IP addresses must start with x.x.x.1 for the first Gateway and be continuously sequential for all subsequent Gateways. Refer to Installation & Programming Manual for instruction.

If a system requires more than one Gateway, an Isolated 8 Port Ethernet Switch is used to route Ethernet data between Gateways, integrating them into the entire distributed Nurse Call Network. Refer to the networking chapter later in System Planning for information about setting up the Jeron IP Network.

Jeron Model 7995 Power Supply with Battery Backup is used to provide local power to the Gateway, corridor Controllers, patient stations, Nurse Consoles, and any Jeron Switches.

If a system requires multiple power supplies for one Gateway on a single JBus run, the diagnostic output ports from up to three power supplies will connect to Model 9776 Gateway Diagnostic Splitter to create a single output port for connection to the Gateway. A Model 9777 power splitter is used to distribute power.

Š 2013 Jeron Electronic Systems Inc.

2-1

Gateways

System Planning

This chapter provides detailed information about these components, which are typically located in utility rooms, and an explanation of power requirements.

Gateways Model 7992/93 Nurse Call Gateway Each Gateway is an IP device that acts as the central transition point, or “gateway”, between the Jeron IP network and the proprietary RS-485 corridor network with attached patient stations or nurse consoles.

Up to 31 Room/Console/Zone Controllers connect on the J Bus on a continuous run to a Gateway via 9779 splitters and a Cat-6 cable (23 AWG).

Maximum distance is 700 ft. The Gateway connects corridor controllers and stations to the Jeron IP Network via industry standard Cat-6/5e cable with RJ45 connectors.

During the hardware installation process, the Gateway automatically learns and saves, in non-volatile memory, the model and identity of each station attached to the corridor network. The 7993 Gateway acquires an IP address from the 7990 Administration Program Software on the PC (refer to networking chapter), which then downloads and configure the data stored in the Gateway to associate it with hospital nursing units.

The Gateway continuously supervises all local devices (Nurse Consoles, Staff Duty or Nurse Terminals, zone lights, Room Controllers, patient stations, pullcord stations, etc.) to ensure every component of the system is operational. If a local device fails, an alert is sent to designated Nurse Console(s), terminal(s), and optionally, to pocket pager(s) carried by support staff.

A Gateway would be utilized on a single floor and may cover all or some of the rooms in a certain unit (floor). One Gateway may be sufficient for multiple units on a floor if the units do not exceed the 31 room limit. A unit may require more than one Gateway if the unit exceeds the number of rooms supported by a Gateway (max 31) or the length of the J Bus exceeds 700 feet.

Gateways should be located in a secure area and are mounted in a standard 19” equipment rack using a Jeron Model 9840 adaptor or a 7988/89 wall cabinet. If connected to a Nurse Call Isolated 8 Port Ethernet Switch, maximum distance from Gateway to switch should not exceed 328 ft. (100 m).

Refer to page 7-1.

2-2

© 2013 Jeron Electronic Systems Inc.

System Planning

Gateways

Figure 2.2: Model 7993 Nurse Call Gateway Note: Each Gateway is factory furnished with one 9778 termination resistor for end-of-line J Bus termination.

Dimensions

(H x W x D): 1.5 x 6.5 x 5.6 inch (3.8 x 16.5 x 14.3 cm)

Mounting

19” rack (using model 9840 adaptor) or wall cabinet. Refer to “Jeron Mounting Kits & Wall Cabinets” on page 8-3

Audio Channels

Eight simultaneous full duplex digital audio Indicators (7993) Two simultaneous full duplex digital audio indicators (7992)

Indicators

8 – Audio Connect (7993) 2 – Audio Connect (7992) 3 – Diagnostic Status 2 – Network Status

Electrical Rating

40V @ 2.2 W 1 – RJ-45 J-Bus port for Room Controllers, Zone lights, and Console Controllers 1 – RJ-45 Ethernet port for nurse call network 1 – Power connector 1 – Diagnostic status

Terminations

Table 2.1: 7992/93 Gateway Technical Data Associated Equipment for Gateways Equipment

Purpose

Isolated 8 Port Ethernet Switch (Model 7991)

Applicable when more than one Gateway is used in a system. Interconnects local Nurse Call Gateways and integrates them into the entire distributed Nurse Call Network. Refer to page 2-5.

Power Supply and Battery Backup (Model 7995)

Powers all nurse call devices including Isolated Switches, Gateways, Nurse Consoles, Staff Duty Terminals, Nurse Terminals, dome lights, patient stations, and staff stations. Refer to page 2-5.

Room/Console/Zone Controllers

Gateways provide control data, power and support eight simultaneous full duplex digital audio connections (Model 7993) to corridor controllers with audio-type room stations

19” Rack (using model 9840 adaptor) or Wall Mount Cabinet 7988/7989

House Gateway

Cat-5/5e/6 Cable

Wires the Gateway to Isolated 8 Port Ethernet Switch (if applicable)

Cat-6 (23 AWG)

Wires Gateways to controllers via 9779 splitters (J Bus)

© 2013 Jeron Electronic Systems Inc.

2-3

Gateways

System Planning

Table 2.2: Associated Equipment for Gateways

2-4

© 2013 Jeron Electronic Systems Inc.

System Planning

Power Supply

Power Supply Model 7995 Power Supply with Battery Backup Powers all nurse call devices including Isolated 8 Port Ethernet Switches, Gateways, touchscreen Nurse Consoles, terminals, dome lights, patient stations, and staff stations.

The number of Power Supplies required depends on the types of devices and stations used on the system and the total size of the system.

Typically, the power supply is rack mounted on 19” rack or wall mounted on 7988/7989 Wall Mount Cabinet within 24 inches of the Gateway.

Figure 2.3: Model 7995 Power Supply with Battery Backup Dimensions

(H x W x D): 4 x 19 x 3.6 inch (10 x 48 x 9 cm)

Enclosure

Metal, black finish

Mounting

19” mounting rack or Model 7988/7989 Wall Cabinet

Connectors and Switches

1 – Fused AC receptacle 1 – Remote diagnostics plug 1 – Main DC power output 3 – Auxiliary DC Power outputs 1 – Power switch 1 – Earth ground lug

Diagnostics LEDs

1 – Ground fault (yellow) 1 – DC Status (green) 1 – Battery charge (yellow) 1 – AC status (green)

Input

120 VAC, 60Hz, 2A

Output

40 VDC @ 100 VA

Battery Backup

Fully charged battery will provide full system operation for a minimum four minutes.

Table 2.3: 7995 Technical Data Required Equipment for Power Supply with Battery Backup Equipment Purpose Wall Mount Cabinet - 7988/7989 or 19” Rack mounted

Houses power supply unit

Two factory furnished 30 inch cables

Wire to Gateway

Two conductor 18 or 16 AWG wires

Wire to Isolated 8 Port Ethernet Switch

Gateway

Provide power to Gateway and its connected devices

Isolated 8 Port Ethernet Switch

Provides power to Isolated 8 Port Ethernet Switch

Table 2.4: 7995 Associated Equipment

© 2013 Jeron Electronic Systems Inc.

2-5

Connecting Gateway & Power Supply

System Planning

Connecting Gateway & Power Supply Together with the 7995 Power Supply and Battery Backup, the Gateway provides control data, power and supports eight simultaneous full duplex digital audio connections (Model 7993) to corridor Controllers with audio-type room stations.

7991 Power to Switch (as required)

Power Supply Model 7995 J200 _

+

To Switch S1

J204

_+

J100

120 VAC Line CAT-5/6

Gateway Model 7993

JBus J1

J2

Factory furnished 30 in. cable

J200 Jeron Network Port

J204

Factory furnished 30 in. cable

CAT-6

Max 31 Room/Master Controllers per Gateway. Maximum 700 ft. J Bus.

To Room/Master Controllers via 9779 Splitter

Figure 2.4: Wiring Power Supply to Gateway

Power Supply Requirements Per Gateway

By Number of J Bus Devices (Prism Dome Lights) 9777 9776 Diagnostic Supplemental Splitter (see Power Wire (see 7967 Terminal below) page 2-8) up to 20 up to 2 1 0 0 up to 31 up to 2 1 1 (Loop or Split) 0 up to 31 up to 4 2 1 (Loop or Split) 1 up to 31 up to 16 3 2 (Loop or Split) 1 One 9777 Power Splitter required for each 7995 Power Supply with more than 20 J Bus devices.

One 9776 Diagnostic Splitter required if there are more 7995 Power Supplies than 7993 Gateways.

One 9776 required for up to three 7995 on same 7993 J Bus. Table 2.5: Power Supply Requirements on J Bus w/ Dome Lights J Bus Devices w/ Prism Dome Light

7965 Console/

7995 Power Supply

For 7967-P Terminal Intercom Operation Only (No Dome Lights) Console Controllers (on a single J Bus)

# of 7967-P Workflow Terminal

7995

9777

9776

up to 8

up to 8

2

1 (Loop or Split)

1

up to 15

up to 15

3

2 (Loop or Split)

1

Table 2.6: Power Supply Requirement for Workflow Terminals

2-6

Š 2013 Jeron Electronic Systems Inc.

System Planning

Connecting Gateway & Power Supply

Multiple Power Supplies on One Gateway The Jeron Model 9776 Gateway Diagnostic Splitter is used to interconnect multiple Model 7995 Power Supplies with one Gateway on a single J-Bus run. The splitter combines the diagnostic output ports from up to three power supplies into a single output port for connection to the Gateway using the factory supplied connectorized cable. This arrangement allows the interconnected power supplies to communicate battery charge, AC status, and ground fault failure messages to a single Gateway. Nurse Console will display these failure messages if so programmed.

For a wiring diagram, refer to Figure 2.5. to 7991 Switch

7995 J200 J201 J204

7995 J200 J204

CAT 6 23 AWG J201 9777-1

7995 J200 CAT 6 23 AWG

J201

J204

9777-1

Factory Cables

9776 Factory furnished cable J204 1

7992/93 J200

2

3

4

5

6

7

J1

9777-2 9779

J-BUS MAX 700ft

15

14

13

12

11

10

9

8

9777-2 T

9779 Termination Resistor (9778)

Figure 2.5: Wiring with Gateway Diagnostic Splitter

Š 2013 Jeron Electronic Systems Inc.

2-7

Connecting Gateway & Power Supply

System Planning

Figure 2.5 displays a single J Bus run of 15 locations (see Table 2.7) with the maximum of 31 Controllers on one Gateway, using three 7995 Power Supplies, two 9777 Power Splitters and a 9776 Gateway Diagnostic Splitter.

J-Bus

Nurse Station (1)

Qty

1 each

Model

Patient Rooms (2-15) 14 each

14 each

7960 Console Controller (J-Bus)

7953 Room Controller with Prism Dome Light (J-Bus)

7960 Console Controller (J-Bus)

7965 Nurse Console (M-Bus)

7923 Patient Station (R-Bus)

7967-P Workflow Terminal (M-Bus)

7931 Call-in Station (P-Bus) Table 2.7: Capacity for One Gateway with Multiple Power Supplies

Supplemental Power Wire The Jeron Model 9777 Power Splitter is used to distribute power when the system requires supplemental power wiring or when the system requires an additional Model 7995 Power Supply.

The 9777 includes two components; the 9777-1 and the 9777-2. The 9777-1 connects directly to the power supply and the 9777-2 connects to the J Bus run using a Cat 6 cable.

Loop Back AUX Power would typically be used in a U shaped hallway with 100 ft. or less between 9777-1 and 9777-2.

Split Aux Power would typically be used in a long, continuous hallway, and could require a second power supply, depending on number of rooms and consoles.

2-8

Š 2013 Jeron Electronic Systems Inc.

System Planning

Connecting Gateway & Power Supply

For each of these scenarios, refer to Figure 2.6.

METHOD 1

LOOP BACK AUX POWER 22

23

21

4

3

7995

7993 7992

1

2

J1

POWER SUPPLY

J200

J5

9779

J-BUS MAX 700ft 24

25

26

27

28

29

30

31

9779

9777-2

9777-1

AUX J201

CAT-6 23 AWG

METHOD 2 SPLIT AUX POWER 30

31

29

7995

16

14

15

2

1

J1

9779

9779

POWER SUPPLY

7993 7992 J5

J200

9779

9777-2

RUN IN SAME CONDUIT AS CAT-6 J-BUS

CAT-6 23 AWG

9777-1

AUX J201

SECOND POWER SUPPLY 31

30

29

16

7

5

6

2

1

9779

9777-2

9777-2

9779

POWER SUPPLY

7993 7992 J1

J5

J200

9779

RUN IN SAME CONDUIT AS CAT-6 J-BUS CAT-6 23 AWG

9777-1

AUX J201

POWER SUPPLY

J200

9777-1

AUX J201

Figure 2.6: Power Splitter Wiring

© 2013 Jeron Electronic Systems Inc.

2-9

Connecting Gateway & Power Supply

2-10

System Planning

© 2013 Jeron Electronic Systems Inc.

Chapter 3: Hallways

.

System Planning

Hallway J Bus Devices

Hallway J Bus Devices

Hallway devices on the Provider 790 include Room, Console, and Zone Controllers. Up to 31 Room/Console/Zone Light Controllers can connect on the J Bus on a continuous run to a Gateway via 9779 splitters and a Cat-6 cable (23 AWG).

Room Controllers supervise and provide power, signaling, and audio (to audio stations) for up to a total of 15 P Bus and R Bus stations located within the same room or area. Some Room Controller models are equipped with dome lights that provide visual indication of any calls associated with the room.

Domeless room controllers are typically used in areas where a dome light is not needed, such as a staff lounge. A Room Controller is typically installed outside the entrance to a room.

Console Controllers provide power, signaling, and audio to a connected touchscreen Nurse Console or Workflow/Staff Duty/Nurse Terminal. Console Controllers are either installed at the nurse station when connected to a Nurse Console, or outside a patient room or staff area where a terminal is located.

One Console Controller is connected per device.

Some Console Controller models are equipped with a zone light for areas where dome lights are not visible. When a zone light is not needed, domeless Console Controller models are installed.

Zone Controllers are typically installed in each corridor intersection, and in any other area where corridor dome lights are not visible to staff from the nurses’ stations. Zone lights provide visual signals to calling stations that are associated with the zone area via programming. They connect only to the J bus devices.

Dome/Zone Lights come with default lights and sequences for call priorities that may be changed via the 7990 Administration Program Software. Refer to page 4-29 for default settings.

Dome/Zone Controllers equipped with the -T option sound alert tones for code calls.

Š 2013 Jeron Electronic Systems Inc.

3-1

Hallway J Bus Devices

System Planning

Room Controllers Audio (R bus) and peripheral (P bus) stations in a room connect to a Room Controller, typically installed outside the entrance to a room. Room stations receive their room name (ID) from the Room Controller to which they connect.

Figure 3.1: Room Controllers (L-R): Model 7950, Model 7951/5253

Model 7950 Room Controller The domeless Room Controller is typically used in areas where a dome light is not needed.

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

none

Electrical Rating

40V @ 1.2 W

Terminations

3 – RJ45 1 – Plug on two-conductor

Table 3.1: 7950 Technical Data

Model 7951 Room Controller and Two Color Dome Lights Provides power, signaling, and audio to a total of 15 stations (audio/nonaudio) located within the same room or area.

The dome light’s high intensity LEDs provide white and red colors in a solid, flashing, or sequencing pattern to give a visual indication of any calls associated with the room.

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

4 – Ultra-bright LED indicators: two white and two red

Electrical Rating

40V @ 1.2 W

Terminations

3 – RJ45 1 – Plug on two-conductor

Table 3.2: 7951 Technical Data

Model 7952 Room Controller and Six Color Dome Lights Provides power, signaling, and audio to a total of 15 stations (audio/nonaudio) located within the same room or area.

3-2

© 2013 Jeron Electronic Systems Inc.

System Planning

Hallway J Bus Devices

The dome light’s high intensity LEDs provide up to six distinct colors in a solid, flashing, or sequencing pattern to give a visual indication of any calls, up to four unique levels of service requirements, or up to three unique levels of staff presence associated with the room. The flexibility of the dome light allows it to simultaneously indicate both the highest call priority in the room plus either an active service requirement set for the room or the highest level of staff present in the room.

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

6 – Ultra-bright LED indicators: white, red, blue, orange, green, and yellow

Electrical Rating

40V @ 1.2 W

Terminations

3 – RJ45 1 – Plug on two-conductor

Table 3.3: 7952 Technical Data

Model 7953 Room Controller and Prism Dome Light Provides power, signaling, and audio to a total of 15 stations (audio/nonaudio) located within the same room or area.

The Prism dome light functionality gives a visual indication of any calls, up to four unique levels of service requirements, or up to three unique levels of staff presence associated with the room. Prism is recommended when needing the range of visual signals necessary for notification of room status events (e.g., rounding, housekeeping, and patient fall notification).

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

8 – Ultra-bright LED indicators: two per Dome Light segment, capable of producing up to eight distinct colors (white, red, yellow, orange, green, blue, magenta, and pink)

Electrical Rating

40V @ 1.2 W

Terminations

3 – RJ45 1 – Plug on two-conductor

Table 3.4: 7953 Technical Data

© 2013 Jeron Electronic Systems Inc.

3-3

Hallway J Bus Devices

System Planning

Associated Equipment for Room Controllers Equipment

Purpose

Back box

To mount the dome light use two-gang backbox with a two-gang trim ring. Refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Factory furnished Cable

To connect Room Controller to Gateway/other devices on the J Bus in series via 9779 Splitter. Each Gateway supports up to 31 rooms (combination of Room/Console/Zone Controllers)

Cat-6 Cable

To connect 9779 splitters in series on the J Bus in a continuous run

Cat-5 (minimum) Cable

To connect to R Bus stations (audio)

Pair of 22 AWG wires

To connect to P Bus stations (peripheral)

R Bus Stations

Connect to Controller

P Bus Stations

Connect to Controller

Gateway

Supports up 31 Room Controllers

Table 3.5: Room Controllers Associated Equipment

3-4

© 2013 Jeron Electronic Systems Inc.

System Planning

Hallway J Bus Devices

Console Controllers Console Controllers are either installed in the nurse stations when connected to a Nurse Console or outside of the patient room/staff area in which Workflow, Staff Duty, or Nurse Terminals are located. One Console Controller is necessary per device.

Figure 3.2: Console Controllers (L-R): Model 7960, Model 7961/62/63

Model 7960 Console Controller Provides power, signaling, and audio for an associated nurse console or workflow/staff duty/nurse terminal.

Dimensions

(H x W x D): 4.8 x 4.9 x 1.1 inch (12.1 x 12.4 x 2.7 cm)

Indicators

none

Electrical Rating

40V @ 1.0 W

Terminations

2 – RJ45

Table 3.6: 7960 Technical Data

Model 7961 Console Controller and Two Color Zone Light Provides power, signaling, and audio for an associated Nurse Console and visual indications of calls for a room, group of rooms, corridor, unit, or up to an entire facility. The zone light’s high intensity LEDs provide white and red colors in a solid, flashing, or sequencing pattern to match the colors and patterns of the dome lights on the system.

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

4 – Ultra-bright LED indicators: two white and two red

Electrical Rating

40V @ 1.0 W

Terminations

2 – RJ45

Table 3.7: 7961 Technical Data

Model 7962 Console Controller and Six Color Zone Light Provides power, signaling, and audio for an associated Nurse Console and visual indications of calls for a room, group of rooms, corridor, unit, or up to an entire facility.

© 2013 Jeron Electronic Systems Inc.

3-5

Hallway J Bus Devices

System Planning

The zone light’s high intensity LEDs provide up to six distinct colors in a solid, flashing, or sequencing pattern to match the colors and patterns of the dome lights on the system.

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

6 – Ultra-bright LED indicators: white, red, blue, orange, green, and yellow

Electrical Rating

40V @ 1.0 W

Terminations

2 – RJ45

Table 3.8: 7962 Technical Data

Model 7963 Console Controller and Prism Zone Light Provides power, signaling, and audio for an associated Nurse Console and visual indications of calls for a room, group of rooms, corridor, unit, or up to an entire facility.

The Prism zone light’s high intensity LED indicators are programmable to provide distinct colors (up to eight) and patterns (up to five) to match the colors and patterns of the dome lights on the system.

Prism is recommended when requiring the range of visual signals necessary for notification of room status events (e.g., rounding, housekeeping, and patient fall notification).

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

8 – Ultra-bright LED indicators: two per dome light segment, capable of producing up to eight distinct colors (white, red, yellow, orange, green, blue, magenta, and pink)

Electrical Rating

40V @ 1.0 W

Terminations

2 – RJ45

Table 3.9: 7963 Technical Data

Associated Equipment for Console Controllers Equipment

Purpose

Back box

To mount the dome light use two-gang backbox with a twogang trim ring. “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Factory furnished Cable

To connect Console Controller to Gateway/other devices on the J Bus in series via 9779 Splitter. Each Gateway supports up to 31 rooms (combination of room/console/zone controllers)

Cat-6 Cable

To connect 9779 splitters in series on the J Bus in a continuous run

Cat-6 (minimum) Cable

To connect to M Bus station (Nurse Console, Workflow/Staff Duty/Nurse terminal)

Gateway

Supports up 31 Controllers

Table 3.10: Console Controllers Associated Equipment

3-6

© 2013 Jeron Electronic Systems Inc.

System Planning

Hallway J Bus Devices

Zone Controllers Zone Controllers provide visual indications of calls for a room, group of rooms, corridor, unit, or up to an entire facility. Zone lights are installed in corridor intersections to direct staff to the call location.

Zone lights connect on the J Bus corridor.

Figure 3.3: Zone Controller Model 7971/72/73

Model 7971 Two Color Zone Light The Zone Light’s high intensity LEDs provide white and red colors in a solid, flashing, or sequencing pattern to match the colors and patterns of the dome lights on the system. The Zone Light indicates the highest priority call within its zone area.

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

4 – Ultra-bright LED indicators: two white and two red

Electrical Rating

40V @ 1.0 W

Terminations

1 – RJ45

Table 3.11: 7971 Technical Data

Model 7972 Six Color Zone Light The Zone Light’s high intensity LEDs provide up to six distinct colors in a solid, flashing, or sequencing pattern to match the colors and patterns of the dome lights on the system. The Zone Light indicates the highest priority call within its zone area.

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

12 – Ultra-bright LED indicators: white, red, blue, orange, green, and yellow

Electrical Rating

40V @ 1.0 W

Terminations

1 – RJ45

Table 3.12: 7972 Technical Data

© 2013 Jeron Electronic Systems Inc.

3-7

Hallway J Bus Devices

System Planning

Model 7973 Prism Zone Light The Prism high intensity LED indicators are programmable to provide distinct colors (up to eight) and patterns (up to five) to match the colors and patterns of the dome lights on the system. The Prism Zone Light indicates the highest priority call within its zone area.

Prism is recommended when requiring the range of visual signals necessary for notification of room status events (e.g., rounding, housekeeping, and patient fall notification).

Dimensions

(H x W x D): 4.8 x 4.9 x 3.7 inch (12.1 x 12.4 x 2.7 cm)

Indicators

8 – Ultra-bright LED indicators: two per light segment, capable of producing up to eight distinct colors (white, red, yellow, orange, green, blue, magenta, and pink)

Electrical Rating

40V @ 1.0 W

Terminations

1 – RJ45

Table 3.13: 7973 Technical Data

Associated Equipment for Zone Lights Equipment

Purpose

Back box

To mount the zone use two-gang backbox with a two-gang trim ring. “Backboxes, Mounting Racks & Wall Cabinets” on page 81.

Factory furnished Cable

To connect zone light to Gateway/other devices on the J Bus in series via 9779 Splitter. Each Gateway supports up to 31 rooms (combination of Room/Console/Zone Controllers)

Cat-6 Cable

To connect 9779 splitters in series on the J Bus in a continuous run

Gateway

Supports up 31 Controllers

Table 3.14: Zone Lights Associated Equipment

3-8

© 2013 Jeron Electronic Systems Inc.

Chapter 4: Patient Rooms & Staff Stations

.

System Planning

Overview of Patient Stations

Overview of Patient Stations

R BUS Patient Stations

Note: Patient stations are provided with default settings and call priorities.

Any station input (except Code) can be configured to place any call priority.

Note: The number of stations installed of a certain type is determined by the facility’s requirements and local healthcare codes.

P BUS Peripheral Stations

The patient/staff audio (R Bus) and peripheral non-audio (P Bus) stations on the Provider 790 Nurse Call System provide the primary means of alerting staff of a call from a room station. The audio stations also provide full duplex communication between patients/staff members and staff at the Nurse Console.

Patient/staff and peripheral stations in a room connect to a Room Controller.

The system supports up to 3,937 rooms, with a maximum 15 combined audio (R Bus) and peripheral (P Bus) stations per Controller. All stations within a room share the same room name (ID) via their connected Room Controller. In rooms with multiple patient beds, beds are distinguished by bed designators.

Device options include single bed patient stations that support one bed and dual patient stations that support two beds for two-way voice communication between patient and staff at the Nurse Console. A number of peripheral stations may be used by staff in a patient room, such as staff emergency, staff presence and code. A bathroom attached to a patient room or a facility bathroom may include audio or peripheral bath stations or peripheral shower stations. A Workflow Terminal (M Bus) that helps manage patient flow efficiently may be installed in a patient room and requires a connection to a Console Controller. Refer to “Call Center M Bus Stations” on page 5-1 for console and terminal specifications.

Staff area options include duty, staff/duty and staff stations with audio. A Staff Duty or Nurse Terminal (M Bus) may be used to annunciate calls and provide audio communication in areas where staff congregate, such as a utility room, break room, or lounge. Each terminal connects to a Console Controller.

All patient and peripheral stations are preprogrammed with default call priorities. However, station inputs can be reprogrammed to place any call

© 2013 Jeron Electronic Systems Inc.

4-1

Overview of Patient Stations

System Planning

priority. In addition, button labels are customizable. For example, if a room requires a station for staff presence in addition to staff emergency, a Model 7940 Procedure, Presence and Bed Management Station may be used. The station is equipped with four preprogrammed buttons that can be reprogrammed for any call type/staff registration. All four of the button labels are replaceable. Four patient station models are equipped with two programmable buttons and labels for any call type. For a list of stations with customizable buttons, refer to page 4-16.

Station enclosures are flame retardant UL 945VA PC/ABS blend polymeric material.

4-2

Š 2013 Jeron Electronic Systems Inc.

System Planning

Audio R Bus Stations

Audio R Bus Stations Most audio R Bus stations have audio capability and enable full-duplex two way voice communication between patient/staff and staff members at the Nurse Console.

Each input on a station comes with a default call-in priority setting that can be changed in programming. Stations are equipped with a cancel button that, in addition to canceling calls placed from the stations themselves, are configurable to selectively cancel any level of call-in on other stations within the same room.

The stations described below are categorized according to their typical location in the facility. However, flexibility in programming station buttons with different call priorities allows stations to be used for other purposes based on the facility’s needs.

Exercise caution when planning audio station location and mounting to ensure quality of full duplex audio will be preserved.

Regardless of the facility location selected, caution must be taken when mounting full duplex audio stations. Avoid blocking speaker or microphone apertures on the front of audio station enclosures. Blocking or masking either speaker or microphone may interfere with the full duplex audio operation and cause unwanted attenuation, echo, or feedback locally as well as remotely on masters and handsets.

The stations connect in series to a Room Controller on the R Bus port via Cat5 or better cable. The stations share the controller’s room name (ID), assigned in programming.

Patient Room Audio Stations

Note: Model 7905 Enhanced Pillow Speakers may be used with both muting and non-muting patient stations. When used with non-muting stations 7920, 7921, 7925, or 7926 ,the dedicated nurse call buttons (Nurse, Water, Pain, and Toilet) and auxiliary controls will operate. Nurse call audio will be routed through the pillow speaker only when used in conjunction with muting patient stations 7923 and 7924.

Patient stations enable patients to place calls to the Nurse Console for assistance. Six patient stations models are available for different room types.

When a call is answered, full-duplex two way voice communication is enabled either through a pillow speaker (when using muting patient station Models 7923 or 7924) or through the wall speaker and panel mic (non-muting Models 7920, 7922, 7925, 7926).

Each patient room may have a single patient station that supports one bed, a dual patient station that supports two beds, or a combination of both. Patients place calls by pressing a button on the pillow speaker or callcord plugged into the station (DIN jacks). The 1/4 inch jacks (Models 7920-7924) can connect to callcords or auxiliary input devices for third party medical equipment.

Calls can also be placed from siderail feature beds connected to patient stations (Models 7920-7924) using the Model 9805 receptacle kit for each bed. Models 7923 and 7924 allow siderail bed audio communication capability, while non-muting patient stations 7920, 7922, 7925, and 7926 allow siderail feature bed exit alarm functionality only.

Models 7920-7924 are equipped with two programmable call buttons for staff use for placing high priority calls. The buttons are preconfigured for Emergency and Code but can be configured and relabeled during setup.

Patient stations are equipped with TV connections. Television must be UL hospital grade, digital control. Only 7923 and 7924 mute TV audio during nurse call audio connection. Individual TV connections per bed are available on the 7921, 7924, and 7926.

Š 2013 Jeron Electronic Systems Inc.

4-3

Audio R Bus Stations

System Planning

Patient stations may be equipped with Model 7906 AUX Modules that provide output to a lighting control via the pillow speakers with auxiliary buttons (Models 7902, 7904 and 7905). Lighting control module is provided by others.

Patient stations are typically mounted in the headwalls above or adjacent to the patient bed.

The stations connect in series to a Room Controller, typically with a dome light.

4-4

Š 2013 Jeron Electronic Systems Inc.

System Planning

Audio R Bus Stations

Private Room A single patient room can use one of the following models:

Model 7920 Single Patient Station Provides up to five discrete call-in points. All nurse call audio is routed to the wall station speaker. Pillow speaker entertainment audio is not muted during nurse call audio.

Equipped with single jacks.

Enabled for signaling from feature beds.

Refer to Figure 4.1 and Table 4.1 below.

Model 7923 Enhanced Single Patient Station Provides up to five discrete call-in points. Bed level nurse call audio is routed to either the pillow speaker or the bed rail speaker. Entertainment audio to the pillow speaker is muted when nurse call audio is connected.

Note: Model 7905 Enhanced Pillow Speaker microphone remains active when used with Model 7923 or 7924 patient stations only.

Shown: Feature bed connector enabled.

Figure 4.1: Model 7923 Enhanced Patient Station

Dimensions

(H x W x D): 4.6 x 6.8 x 1.2 inch (11.7 x 17.2 x 3 cm)

Controls/Indicators

1 – DIN jack with call placed LED 1 – ¼” jack with call placed LED 1 – Feature bed status and call placed LED 2 – Configurable call buttons with call placed LEDs 1 – Cancel button with remote call cancel LED 1 – Monitor LED 2 – Low ambient light LEDs

Speaker

2.75 inch (7 CM); 8 Ohm

Microphone

Electret

Electrical Rating

5V @ 200 mW

Terminations

2 – RJ45 3 – Plug on IDC multiconductors

Table 4.1: 7923 Technical Data

© 2013 Jeron Electronic Systems Inc.

4-5

Audio R Bus Stations

System Planning

Model 7925 Single Patient Station Provides one DIN plug call-in point.

Figure 4.2: Model 7925 Single Patient Station Dimensions

(H x W x D): 4.6 x 6.8 x 1.2 inch (11.7 x 17.2 x 3 cm)

Controls/Indicators

1 – DIN jack with call placed LED 1 – Cancel button 1 – Monitor LED 2 – Low ambient light LEDs

Speaker

2.75 inch (7 CM); 8 Ohm

Microphone

Electret

Electrical Rating

5V @ 200 mW

Terminations

2 – RJ45 4 – Plug on IDC multiconductors

Table 4.2: 7925 Technical Data

Semi-Private Room A semi-private room is intended for two patients and can use one of the following models:

Model 7922 Dual Patient Station Provides up to eight discrete call-in points. Nurse call audio always goes through the wall station speaker.

Equipped with dual jacks.

Refer to Figure 4.3 and Table 4.3.

Model 7924 Enhanced Dual Patient Station Provides up to eight discrete call-in points. Bed level nurse call audio goes through the pillow speaker or the bed rail speaker. Entertainment audio is muted when nurse call audio is connected. Equipped with dual DIN jacks and 1/4 inch jacks.

4-6

© 2013 Jeron Electronic Systems Inc.

System Planning

Audio R Bus Stations

Note: Model 7905 Enhanced Pillow Speaker microphone remains active when used with Model 7923 or 7924 patient stations only.

Figure 4.3: Model 7924 Enhanced Dual Patient Station Dimensions

(H x W x D): 4.6 x 6.8 x 1.2 inch (11.7 x 17.2 x 3 cm)

Controls/Indicators

2 – DIN jacks with call placed LEDs 2 – ¼” jacks with call placed LEDs 2 – Feature bed status and call placed LEDs 2 – Configurable call buttons with call placed LEDs 1 – Cancel button with remote call cancel LED 1 – Monitor LED 2 – Low ambient light LEDs

Speaker

2.75 inch (7 CM); 8 Ohm

Microphone

Electret

Electrical Rating

5V @ 200 mW

Terminations

2 – RJ45 6 – Plug on IDC multiconductors

Table 4.3: 7924 Technical Data

Model 7926 Dual Patient Station Provides two DIN plug call-in points.

Figure 4.4: Model 7926 Dual Patient Station

© 2013 Jeron Electronic Systems Inc.

4-7

Audio R Bus Stations

System Planning

Controls/Indicators

2 – DIN jacks with call placed LEDs 1 – Cancel button 1 – Monitor LED 2 – Low ambient light LEDs

Speaker

2.75 inch (7 CM); 8 Ohm

Microphone

Electret

Electrical Rating

5V @ 200 mW

Terminations

2 – RJ45 4 – Plug on IDC multiconductors

Table 4.4: 7926 Technical Data

Model 7920, 7923, 7926 Single Patient Stations You may instead use two single patient stations from these model types for a semi-private room.

Ward A ward can be occupied by several patients. You can use a variation of the patient station models mentioned above.

Associated Equipment for Patient Stations Equipment

Purpose

Back box

To mount Model 7925 or 7926, use two gang backbox with two gang trim ring.

To mount 7920, 7922, 7923, or 7924, use three-gang backbox with three-gang trim ring. For specific backbox type, refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1.

Callcord(s) or pillow speaker(s)

To call Nurse Console. Refer to page 4-34 and page 4-40.

Room Controller

To distribute power, data, audio to station. Refer to page 3-2.

Cat-5/5e/6 cable

To wire station to Room Controller and/or other R bus stations in series

9805 receptacle kit

For siderail beds

7947 8 Input Station

Provides connector for bed. Required for Stryker® beds equipped with iBed Awareness™.

Table 4.5: Associated Equipment for Patient Stations

Customizable Button Labels on Audio Stations Refer to table below for button labels that are replacable.

4-8

© 2013 Jeron Electronic Systems Inc.

System Planning

Audio R Bus Stations

Station Model 7920/7922 7923/7924

Default Button Labels Emergency & Code

Table 4.6: Audio Stations with Customizable Button Labels

Relays on Patient Stations for Light Controllers Pillow speakers with auxiliary buttons plugged into patient stations can control third party room lighting. Patient stations are equipped with a relay (IDC header) that requires the connection of a Model 7906 Pillow Speaker Auxiliary Output Module. Refer to page 4-39. Model 7906 then connects to the lighting control relay provided by others.

Š 2013 Jeron Electronic Systems Inc.

4-9

Audio R Bus Stations

System Planning

Staff Areas Staff and Staff/Duty stations enable staff to call the nurses’ station and communicate with staff members from their work areas. Staff/Duty stations also annunciate calls placed by stations in their duty areas.

Model 7917 Visual Duty station is a non-audio station that annunciates calls placed by stations assigned to its duty area and connects to the room controller on the R Bus. Staff, Staff/Duty and Visual Duty stations are typically installed near doors in areas where staff members work, such as staff lounges, clean workrooms, medical preparation rooms, and examination/treatment rooms.

The audio stations and duty stations are connected in series to a Room Controller on the R Bus. Note: The Staff/Duty Station (Model 7927) requires a dedicated Room Controller.

Model 7912 Staff Station Provides a single level of call-in. The call button is preconfigured for a staff call-in level, but can be field configured for any of the available call priority levels on the system.

Figure 4.5: Model 7912 Staff Station

Dimensions (H x W x D)

4.8 x 4.8 x 1.2 inch (12.2 x 12.2 x 3 cm)

Controls/Indicators

1 – Call button with call placed LED 1 – Cancel button 1 – Monitor LED 1 – Low ambient light LED

Speaker

2.75 inch (7 CM); 8 Ohm

Microphone

Electret

Electrical Rating

5 V @ 85 mW

Terminations

1 – RJ45

Table 4.7: 7912 Technical Data

4-10

© 2013 Jeron Electronic Systems Inc.

System Planning

Audio R Bus Stations

Model 7916 PA Page Interface Interfaces the 790 system to external public address page systems or to an all-call page amplifier.

Requires a dedicated Room Controller not shared with any R Bus or P Bus station.

Figure 4.6: Model 7916 PA Page Interface

Dimensions

(H x W x D): 4.8 x 4.9 x 1.1 inch (12.1 x 12.4 x 2.7 cm)

Diagnostic LED

1 – Green LED 1 – Red LED (Audio page on)

Electrical Rating

5 V @ 85 mW

Terminations

2 – RJ45

Figure 4.7: 7916 Technical Data

Associated Equipment for PA Page Interface Equipment

Purpose

Backbox Required

To mount station use two gang backbox with two gang trim ring. For specific backbox type, refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1.

Dedicated Room Controller

To distribute power, data to station. Refer to page 3-2.

Cat-5/5e/6 cable

To wire station to Room Controller.

PA Amplifier provided by others

Table 4.8: Associated Equipment for PA Page Interface

© 2013 Jeron Electronic Systems Inc.

4-11

Audio R Bus Stations

System Planning

Model 7917 Visual Duty Station Annunciates calls in areas where staff may congregate, examination treatment room, medication preparation room, multipurpose room, etc. The Visual Duty Station is not a nurse call audio station but connects on the R Bus in series to a Room Controller.

Use Model 9707 splitter to connect two 7917 duty stations to the same R Bus. Do not use a 9779 J Bus splitter. A maximum of four 7917 stations per R Bus is allowed.

Multiple 7927 Staff/Duty and 7917 Duty stations on the same Room Controller must be assigned the same duty area in programming.

Figure 4.8: Model 7917 Visual Duty Station

Note: Do not connect Visual Duty station to the same Room Controller as 7918 Electrical Supervision station

Dimensions (H x W x D)

4.6 x 3 x 1 inch (7 x 7.6 x 2.5 cm)

Controls/Indicators

1 – Green “Routine” LED call indicator 1 – Amber “Urgent” LED call indicator 1 – Red “Emer” LED call indicator 1 – Blue “Code” LED call indicator 1 – Tone mute button 1 – Low ambient light LED 1 – Alert tone generator

Electrical Rating

5 V @ 125 mW

Terminations

1 – RJ45

Figure 4.9: 7917 Technical Data

4-12

© 2013 Jeron Electronic Systems Inc.

System Planning

Audio R Bus Stations

Model 7927 Staff/Duty Station Provides a single level of call-in. Also annunciates calls in areas where staff congregates.

Use Model 9707 splitter to connect 7927 to 7917 or Room Controller. Do not use a 9779 J Bus splitter.

A 7927 Staff/Duty and multiple 7917 Duty stations (up to 3) on the same Room Controller must be assigned the same duty area in programming.

Figure 4.10: Model 7927 Staff/Duty Station

A Staff/Duty Station can not share a room controller (on the R Bus) with other audio stations, except for 7917 Duty Stations.

Dimensions (H x W x D)

4.8 x 4.8 x 1.2 inch (12.2 x 12.2 x 3 cm)

Controls/Indicators

1 – Green “Routine” LED call indicator 1 – Amber “Urgent” LED call indicator 1 – Red “Emer” LED call indicator 1 – Blue “Code” LED call indicator 1 – Call button 1 – Combination tone mute/cancel button 1 – Monitor LED 1 – Low ambient light LED

Electrical Rating

5 V @ 125 mW

Terminations

1 – RJ45

Table 4.9: 7927 Technical Data

Associated Equipment for Staff Audio Stations Equipment

Purpose

Backbox Required

To mount station Models 7912 and 7927 use two gang backbox with two gang trim ring.

To mount station Model 7917 use one gang backbox or two gang with one gang trim ring. For specific backbox type, refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1.

Room Controller

To distribute power, data, audio (7912, 7927) to station. Refer to page 32. Model 7927 must have a dedicated Room Controller.

Cat-5/5e/6 cable

To wire station to Room Controller and/or other R Bus stations in series

Table 4.10: Associated Equipment for Staff Stations

© 2013 Jeron Electronic Systems Inc.

4-13

Audio R Bus Stations

System Planning

Patient & Facility Bathrooms Pushbutton and Pullcord Bath w/Audio stations enable patients to place calls to the Nurse Console and conduct two way audio communication from a patient or facility toilet and bath area.

If the station is installed in the bathroom of a patient room and connected to the same Room Controller as the other stations, it will share the room name of all other stations in the room. The station may also be installed as a stand alone in a facility bathroom and connect to its own Room Controller on the R Bus.

Model 7919 Pullcord & Pushbutton Bath Station (with Audio) Provides audio communications and one or two call-in setting for button and pullcord. The pullcord and pushbutton are preconfigured for Bath Assist and Bath Emergency call-in levels respectively, but can be field configured for any of the available call priority levels on the system.

Figure 4.11: Model 7919 Pullcord & Pushbutton Bath Station w/Audio

Controls/Indicators

1 – Configurable call buttons with call placed LED 1 – 6 ft. (1.8 m) blue PVC coated nylon pullcord 1 – Cancel button 1 – Monitor LED 1 – Low ambient light LEDs

Dimensions (H x W x D)

4.8 x 4.8 x 1.2 inch (12.2 x 12.2 x 3 cm)

Speaker

2.75 inch (7 CM); 8 Ohm

Microphone

Electret

Electrical Rating

5 V @ 85 mW

Terminations

1 – RJ45

Table 4.11: 7919 Technical Data

4-14

© 2013 Jeron Electronic Systems Inc.

System Planning

Audio R Bus Stations

Associated Equipment for Bath Stations Equipment

Purpose

Back box

To mount station use two-gang box with two-gang trim ring. For specific backbox type, refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1.

Room Controller

To distribute power, data, audio to station. Refer to page 3-2.

Cat-5/5e/6 cable

To wire station to Room Controller, and/or other R Bus stations in series

Table 4.12: Associated Equipment for Bath Stations

© 2013 Jeron Electronic Systems Inc.

4-15

Audio R Bus Stations

System Planning

Utility Rooms Electrical Supervision stations provide continuous electrical supervision of the Provider 790 Nurse Call System and report diagnostic conditions to the staff members.

The Electrical Supervision Station does not have nurse call audio capability but it is wired to a dedicated Room Controller on the R bus.

Model 7918 Electrical Supervision Station Alerts staff of any system issues.

Figure 4.12: Model 7918 Electrical Supervision Station

Note: Each Electrical Supervision Station requires a dedicated Room Controller. Do not connect 7917 Duty or 7927 Staff/Duty Stations to the same Room Controller as 7918.

Dimensions (H x W x D)

4.6 x 3 x 1 inch (7 x 7.6 x 2.5 cm)

Controls/Indicators

1 – Blue “Trouble” LED indicator 1 – Red “Ground Fault” LED indicator 1 – Yellow “Console/Power Fail” LED indicator 1 – Green “Station/Dome/Zone” LED indicator 1 – Tone mute button 1 – Low ambient light LED 1 – Alert tone generator

Electrical Rating

5 V @ 125 mW

Terminations

1 – RJ45

Table 4.13: 7918 Technical Data

Associated Equipment for Electrical Supervision Stations Equipment

Purpose

Back box

To mount station use one gang backbox or two gang with one gang trim ring. For specific backbox type, refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Room Controller

To distribute power, data

Cat-5/5e/6 cable

To connect station to Room Controller

Table 4.14: Associated Equipment for Electrical Supervision Stations

4-16

© 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Peripheral P Bus Stations Peripheral stations (non-audio) add call-in priorities to a room and are used by staff to place calls to the Nurse Console and alert staff members of a need of assistance. Peripherals have no audio capability but can be associated with an audio station in the room in programming. When a call is placed from the peripheral station and is answered at the Nurse Console, audio can be heard thru the speaker of the associated audio station.

Inputs are provided with default settings that can be changed in programming to any call type to meet the facility’s needs. Some stations have buttons that can be relabeled during setup using labels that slide in between the faceplate membrane and the switch. Cancel buttons can be configured to cancel calls from any station in a room.

Peripheral stations connect in series to a Room Controller on the P Bus port via single 22 AWG UTP cable. They share the room number with their Room Controller.

Patient Rooms & Staff Areas Peripheral stations are typically installed in patient rooms & staff areas for the use of staff members.

The Staff Presence stations allow staff to manually register in and out of patient rooms and other staff areas, supporting quick locating of staff members. Staff Presence is typically installed near the patient room door.

The Procedure, Presence, and Bed Management Station may provide staff presence, rounding, bed management, procedure event initiation, or place one or more levels of call.

The Dual Auxiliary Alarm Input Station is equipped with two inputs for alarms from ancillary devices or for bed exit alarms. Dual Input Stations are typically installed in the same room as their associated patient or staff stations.

The Dual External Alarm Input Station provides external inputs for alarms from ancillary devices such as fire alarms and door contacts.

The Remote Cancel Station allows staff to remotely cancel outstanding calls or service requirements set at other stations within the same room or area.

Š 2013 Jeron Electronic Systems Inc.

4-17

Peripheral P Bus Stations

System Planning

Model 7934 Staff Presence Station Equipped with three buttons for three levels of staff presence: green, orange, and yellow. Provides one button activation of both staff presence and remote service requirement cancel.

Figure 4.13: Model 7934 Staff Presence Station

Controls/Indicators

1 – Green staff presence push button with LED indicator 1 – Orange staff presence push button with LED indicator 1 – Yellow staff presence push button with LED indicator 1 – Cancel button 1 – Low ambient light LED

Dimensions (H x W x D)

4.6” x 3” x 1” (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5V @ 25 mW

Terminations

1 plug on two conductor screw terminal

Table 4.15: 7934 Technical Data

4-18

© 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Model 7937 Remote Cancel Station The Remote Cancel station is configurable to selectively cancel all or select levels of calls and service requirements set on other stations within the same room. The station is installed in any room equipped with call stations that require a cancel point.

Figure 4.14: Model 7937 Remote Cancel Station

Controls/Indicators

1 – Cancel button 1 – Low ambient light LED

Dimensions (H x W x D)

4.6” x 3” x 1” (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5V @ 25 mW

Terminations

1 plug on two conductor screw terminal

Table 4.16: 7937 Technical Data

Associated Equipment for Remote Cancel Stations Equipment

Purpose

Back box

To mount station use one gang backbox or two gang with one gang trim ring. For specific backbox type, refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Room Controller

To distribute power, data. Refer to page 3-2.

Pair of 22 AWG wires

To wire station to Room Controller and/or other P Bus stations in series

Call Stations

To remotely cancel calls placed in a room from this station

Table 4.17: 7937 Associated Equipment

© 2013 Jeron Electronic Systems Inc.

4-19

Peripheral P Bus Stations

System Planning

Model 7940 Procedure, Presence, and Bed Management Station Equipped with four buttons field configurable for event initiation, call placement, or staff presence. The four buttons are configured and operate independently of each other. The buttons can be relabeled during setup using labels that slide in between the faceplate membrane and the switch itself.

Figure 4.15: Model 7940 Procedure, Presence, and Bed Management Station

Controls/Indicators

4 – Call/Event/Presence pushbuttons with LED indicators 1 – Cancel button 1 – Low ambient light LED

Dimensions (H x W x D)

4.6” x 3” x 1” (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5V @ 25 mW

Terminations

1 plug on two conductor screw terminal

Table 4.18: 7940 Technical Data

Associated Equipment for Staff Presence & Procedure, Presence, and Bed Management Stations Equipment

Purpose

Back box

To mount station use one gang backbox or two gang with one gang trim ring. For specific backbox type, refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Room Controller

To distribute power, data. Refer to page 3-2.

Pair of 22 AWG wires

To wire station to Room Controller and/or other P Bus stations in series

Audio Room Station

To provide audio capability in the room (for 7940 only), if button(s) is configured for call

Table 4.19: 7934 & 7940 Associated Equipment

4-20

© 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Model 7941 Dual Auxiliary Alarm Input Station Provides two discrete alarm input points and associated unique call priorities.

The station is equipped with inputs for connection of medical equipment such as ventilators, infusion pumps, pulse oxymeters, or IV drip monitors. It may also be used for placing calls with callcords. The two ¼” jacks are preconfigured for “Alarm 1” and “Alarm 2” call levels, but can be field configured for any of the available call priority levels on the system. The ¼” jack labels can be relabeled during setup using labels that slides behind the faceplate membrane.

Figure 4.16: Model 7941 Dual Auxiliary Alarm Input Station Note: Patient stations 7920-7924 are equipped with 1/4” jacks that can be used as auxiliary inputs.

The auxiliary peripheral stations can be used in addition to the auxiliary inputs on the patient stations or as stand alone stations.

Controls/Indicators

2 – 1/4” jack inputs with call placed LEDs 1 – Cancel button 1 – Low ambient light LED

Dimensions (H x W x D)

4.6” x 3” x 1” (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5V @ 25 mW

Terminations

1 plug on two conductor screw terminal

© 2013 Jeron Electronic Systems Inc.

Table 4.20: 7941 Technical Data

4-21

Peripheral P Bus Stations

System Planning

Model 7945 Dual External Alarm Input Station The station provides two discrete dry contact alarm input points and associated unique call priorities. When tied to other life and security systems, such as fire alarm, the alarm annunciation through the Provider nurse call is for redundant annunciation and is not intended as the only means of alarm annunciation. The two alarm inputs are preconfigured for “Alarm 1” and “Alarm 2” call levels, but can be field configured for any of the available call priority levels on the system. The alarm input designators can be relabeled during setup using labels that slides behind the faceplate membrane.

Figure 4.17: Model 7945 Dual External Alarm Input Station

Controls/Indicators

2 - Alarm placed LEDs 1 - Cancel button 1 - Low ambient light LED

Dimensions (H x W x D)

4.6” x 3” x 1” (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5V @ 25 mW

Terminations

1 - Plug on two-conductor screw terminal 2 - 2-conductor IDC connectors

Table 4.21: 7945 Technical Data

Associated Equipment for Auxiliary Input Stations Equipment

Purpose

Back box

To mount station use one gang backbox or two gang with one gang trim ring. For specific backbox type, refer to “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Room Controller

To distribute power, data. Refer to page 3-2.

Pair of 22 AWG wires

To wire station to Room Controller and/or other P Bus stations in series

Audio Room Station

To provide audio capability in the room

7941

1/4” plug callcords or plugs for auxiliary devices

Table 4.22: 7941 & 7945 Associated Equipment

4-22

© 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Model 7947 8 Input Bed Interface Allows the integration of Stryker® side rail beds with iBed Awareness feature.

New call types must be created in 7990 for each of the iBed outputs in order for these events to annunciate at the console/dome lights, etc. The eight iBed outputs are awareness enabled, brake set, bed exit enabled, bed exit alarm, side rail down, low Fowler angle, awareness alert, and low bed height.

Figure 4.18: Model 7947 8 Input Bed Interface

Controls/Indicators

none

Dimensions (H x W x D)

4.6” x 3” x 1” (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5 V @ 25 mW

Terminations

1 - Plug on two-conductor screw terminal 1 - IDC connector

Figure 4.19: 7947 Technical Data

© 2013 Jeron Electronic Systems Inc.

4-23

Peripheral P Bus Stations

System Planning

Patient or Facility Bathroom & Shower Some peripheral stations are typically installed in a patient bath/shower area or in a facility bath/shower area. Stations are typically equipped with a pullcord and pushbutton to call for assistance. The pullcord and call button are preconfigured for Assist and Bath call levels respectively, but can be field configured for any of the available call priority levels on the system. The call button can be relabeled during setup using a label that slides in between the faceplate membrane and the switch.

Stations in a room share the Room Controller’s name (ID).

The Pullcord & Pushbutton station is intended for use near the toilet where it is not exposed to water.

The Shower station is intended for use in shower locations where direct water spray may be encountered. The station is equipped with a wall gasket.

Model 7932 Pullcord & Pushbutton Station Provides two discrete call-in points and associated unique call priorities. For a similar station with audio, refer to “Model 7919 Pullcord & Pushbutton Bath Station (with Audio)” on page 4-14.

Figure 4.20: Model 7932 Pullcord & Pushbutton Station Dimensions (H x W x D)

4.6” x 3” x 1” (7 x 7.6 x 2.5 cm)

Controls/Indicators

1 – Configurable call button with call placed LED 1 – 6 ft. (1.8 m) blue PVC coated pullcord 1 – Cancel button 1 – Low ambient light LED

Electrical Rating

5V @ 25 mW

Terminations

1 Plug on two conductor screw terminal

Table 4.23: 7932 Technical Data

4-24

© 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Model 7958 Shower Station When installed with the included wall gasket, the station is sealed against moisture allowing it to be mounted in a wet environment or in a direct water spray. Tile grout seams may require local application of a sealant.

Figure 4.21: Model 7958 Shower Station Dimensions (H x W x D)

4.6” x 3” x 1” (7 x 7.6 x 2.5 cm)

Controls/Indicators

1 – Configurable call button with call placed LED 1 – 6 ft. (1.8 m) blue PVC coated pullcord 1 – Cancel button 1 – Low ambient light LED

Electrical Rating

5V @ 25 mW

Terminations

1 Plug on two conductor screw terminal

Table 4.24: Model 7958 Technical Data

-R Relay Option for 7932 Pullcord & Pushbutton Station or 7958 Shower Station For use with an auxiliary bathroom dome light with a dedicated 7995 Power Supply. Only one bath/shower station requires the -R option.

Associated Equipment for Pullcord & Pushbutton Station & Shower Station Equipment

Purpose

Back box

To mount station use one gang backbox or two gang with one gang trim ring. “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Room Controller

To distribute power, data. Refer to page 3-2.

Pair of 22 AWG wires

To wire station to Room Controller and/or other P Bus stations in series

Audio Room Station

To provide audio capability in the room if audio communication is necessary

7958

Equipped with gasket kit for wet environment

Table 4.25: 7932/7958 Associated Equipment

© 2013 Jeron Electronic Systems Inc.

4-25

Peripheral P Bus Stations

System Planning

Other Facility Rooms A number of peripheral stations can be installed in patient rooms, staff areas, exam rooms, treatment rooms, or any room where patient/staff require the ability to place calls to the Nurse Console. These stations may either be stand alone stations that have a dedicated Room Controller and room name (ID), or they may be installed in a room with multiple stations connected to a single Room Controller and share an ID with those stations.

Model 7930 Single Pushbutton Station Provides a single level of call-in. The built-in call button is preconfigured for an Emergency call-in level, but can be field configured for any of the available call priority levels on the system. The call button can be relabeled during setup using a label that slides in between the faceplate membrane and the switch itself. This station is typically installed in treatment, examination, operating, or patient rooms.

Figure 4.22: Model 7930 Single Pushbutton Station

Controls/Indicators

1 – Configurable call button with call placed LED 1 – Cancel button 1 – Low ambient light LED

Dimensions (H x W x D)

4.6 x 3 x 1 inch (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5V @ 25 mW

Terminations

1 plug on two conductor screw terminal

Provided

Replaceable labels for “Call” button

Table 4.26: 7930 Technical Data

4-26

© 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Model 7931/7931-P Dual Pushbutton Station Provides two discrete call-in points and associated unique call priorities.

Programmed by default to Staff Emergency and Code Blue (on 7931) or Staff Emergency and Code Pink (on 7931-P) calls. The station is typically installed in treatment, examination, triage or operating rooms, critical bed care locations, radiology departments, etc. .

Figure 4.23: Model 7931/7931-P Dual Pushbutton Station

Controls/Indicators

2 – Call buttons with call placed LEDs 1 – Cancel button 1 – Low ambient light LED

Dimensions (H x W x D)

4.6” x 3” x 1” (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5V @ 25 mW

Terminations

1 plug on two conductor screw terminal

Provided

Replaceable labels for “Staff Emer” (top) button

Table 4.27: 7931/7931-P Technical Data

© 2013 Jeron Electronic Systems Inc.

4-27

Peripheral P Bus Stations

System Planning

Model 7949/7949-P Code Blue/Code Pink Station Provides a single level of Code Blue/Code Pink call-in. Code calls take precedence over all other call priorities on the system. Code Blue stations are typically installed in recovery, emergency exam, treatment or triage rooms, and critical care bed locations. Code Pink stations are typically installed in pediatric departments.

Figure 4.24: Model 7949/7949-P Code Stations

Controls/Indicators

1 – Code blue/pink button with call placed LED 1 – Cancel button 1 – Low ambient light LED

Dimensions (H x W x D)

4.6” x 3” x 1” (11.7 x 7.6 x 2.5 cm)

Electrical Rating

5V @ 25 mW

Terminations

1 plug on two conductor screw terminal

Table 4.28: 7949/7949-P Technical Data

Associated Equipment for Code Blue/Pink Stations Equipment

Purpose

Back box

To mount station use one gang backbox or two gang with one gang trim ring. “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Room Controller

To distribute power, data. Refer to page 3-2.

Pair of 22 AWG wires

To wire station to Room Controller and/or other P Bus stations in series

Audio Room Station

To provide audio capability in the room if audio communication is necessary

Table 4.29: 7949/7949-P Associated Equipment

-R Relay Option for 7931 and 7949 Stations Activate for use with an external low voltage code timer when a code call is placed from a code station on the Room Controller. Only one code station in the room requires the -R option.

4-28

© 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Peripheral Station Configuration Options •

Peripheral stations do not have audio capability and may be associated in programming with a specific audio station in its room.

Answering a call placed by a peripheral station at the Nurse Console opens an audio connection to the associated patient (or other audio) station. Association is achieved in the 7990 Administration software application.

•

Provided button labels for a number of call types slide behind switch membrane allowing flexibility in button labeling. Refer to section below.

•

Cancel button on any station may be programmed to cancel calls placed on remote stations in a room.

Customizable Call Button Labels on Peripheral Stations Refer to table below for stations & button labels that may be customized.

Station Model

Customizable Button Label

7930

Single Pushbutton

7931

Top button - "Staff Emer" only

7940

Four label slots

7941

Two label slots

7945

Two label slots

Figure 4.25: Peripheral Stations with Customizable Button Labels

Call Types & Indications Over 1,000 unique call priorities are available on the system and are divided into four categories--routine, urgent, emergency, and code--for common call indication at Nurse Consoles, Terminals, Room Controllers with Dome Lights, Console Controllers with Zone Lights, Zone Light Controllers, Model 7917 Visual Duty Stations, and Model 7927 Staff/Duty Stations.

Alert tones indicate the call level by both frequency and pulse rate. Call status indicators show the call level by both color and flash rate on four separate LED indicators. Individual calls at the Nurse Console indicate their level by the flash rate. Dome Lights and Zone Lights indicate the specific call type (not just level) by its color and/or flash sequence. Refer to Table 4.29.

All Dome/Zone Light flash rates and alert tones are configurable in 7990. The table below lists the default settings.

© 2013 Jeron Electronic Systems Inc.

4-29

Peripheral P Bus Stations

System Planning

Light Show # Dome/Zone Light 7952/7962/7972 6 LED

Nurse Console Call Type/Event/Priority # Display Message

Call Status LED & Alert Tone

Dome/Zone Light 7953, 7963, 7973 Prism

Visual Signals

9 - Relay Access 10 - Remote Privacy

Status Indicators

15 - AIDE RMD 15M

AIDE REMIND 15M

16 - AIDE RMD 15M OT1

AIDE REMIND 15M OT1

241 - Yellow (4th segment) slow flash

17 - AIDE RMD 15M OT2

AIDE REMIND 15M OT2

245 - Yellow (4th segment) fast flash

18 - AIDE RMD 30M 19 - AIDE RMD 30M OT1

241 - Yellow (4th segment) slow flash

20 - AIDE RMD 30M OT2

245 - Yellow (4th segment) fast flash

21 - AIDE RMD 60M 22 - AIDE RMD 60M OT1

241 - Yellow (4th segment) slow flash

23 - AIDE RMD 60M OT2

245 - Yellow (4th segment) fast flash

24 - AIDE RMD 2HR 25 - AIDE RMD 2HR OT1

241 - Yellow (4th segment) slow flash

26 - AIDE RMD 2HR OT2

245 - Yellow (4th segment) fast flash

27 - 38 CNA RMD 15, 30, 60, 2HR, each with OT1s and OT2s

CNA REMIND 15M, etc.

for OT1s: 242 - Orange (4th segment) slow flash for OT2s: 246 - Orange (4th segment) fast flash

39 - 50 RN RMD 15, 30, 60, 2HR, each with OT1s and OT2s

RN REMIND 15M, etc.

for OT1s: 243 - Green (4th segment) slow flash for OT2s: 247 - Green (4th segment) fast flash

51 - AIDE RND 15M

AIDE ROUND 15M

52 - AIDE RND 15M OT1

AIDE ROUND 15M OT1

241 - Yellow (4th segment) slow flash

53 - AIDE RND 15M OT2

AIDE ROUND 15M OT2

245 - Yellow (4th segment) fast flash

54 - AIDE RND 30M 55 - AIDE RND 30M OT1

241 - Yellow (4th segment) slow flash

56 - AIDE RND 30M OT2

245 - Yellow (4th segment) fast flash

57 - AIDE RND 60M 58 - AIDE RND 60M OT1

241 - Yellow (4th segment) slow flash

59 - AIDE RND 60M OT2

245 - Yellow (4th segment) fast flash

60 - AIDE RND 2HR

4-30

61 - AIDE RND 2HR OT1

241 - Yellow (4th segment) slow flash

62 - AIDE RND 2HR OT2

245 - Yellow (4th segment) fast flash

63 - 74 CNA RND 15, 30, 60, 2HR, each with OT1s and OT2s

CNA ROUND 15M, etc. following same display as above

for OT1s: 242 - Orange (4th segment) slow flash for OT2s: 246 - Orange (4th segment) fast flash

75 - 86 RN RND 15, 30, 60, 2HR, each with OT1s and OT2s

RN ROUND 15M, etc. following same display as above

for OT1s: 243 - Green (4th segment) slow flash for OT2s: 247 - Green (4th segment) fast flash

© 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Light Show # Dome/Zone Light 7952/7962/7972 6 LED

Nurse Console Call Type/Event/Priority # Display Message

Call Status LED & Alert Tone

Dome/Zone Light 7953, 7963, 7973 Prism

Visual Signals

120 - Bed Clean

20 - White (1st segment) med. flash

White (3rd segment) med. flash

122 - Transport Req

22- White (1st segment)

White (3rd segment)

24 - Red (2nd segment) med. flash

Red (3rd segment)

123 - Room Clean 124 - Bed Dirty 126 - Hskeep Present Status

127 - Room Dirty 200 - Aide Present

237- Yellow (4th segment)

202 - CNA Present

238 - Orange (4th segment)

204 - RN Present

239 - Green (4th segment)

220 - Aide Request

241 - Yellow (4th segment) med. flash

221 - CNA Request

242 - Orange (4th segment) med. flash

222 - RN Request

243 - Green (4th segment) med. flash

310 - Ground Fault

Ground Fault

320 - Failed Station

Failed Station

321 - Zone Light Fail

Zone Light Fail

322 - Room Cont Fail

Room Cont Fail

328 - Bed Siderail Left Bed

Bed Siderail

55 - White (1st segment)

329 - Bed Siderail Right Bed

Bed Siderail

56 -White (1st segment)

330 - Normal Left Bed

Normal

55- White (1st segment)

332- Normal Right Bed

Normal

56 -White (1st segment)

333 - Water Left Bed

Water

55- White (1st segment)

334 - Water Right Bed

Water

56 -White (1st segment)

335 - Toilet Left Bed

Toilet

336 - Toilet Right Bed

Toilet

337 - Pain Left Bed

Pain

55- White (1st segment)

338 - Pain Right Bed

Pain

56 -White (1st segment)

White (2nd segment)

340 - Staff

Staff

57 -White (1st segment)

White (3rd & 4th segment)

350 - Pers Att - Left Bed

Pers Att

55- White (1st segment)

352 - Pert Att - Right Bed

Pers Att

56 -White (1st segment)

360 - Aide Reminder

Aide Reminder

241 - Yellow (4th segment) slow flash

White (2nd segment)

White (2nd segment)

White (2nd segment)

55- White (1st segment) Routine

56 -White (1st segment)

White (2nd segment)

White (2nd segment)

361 - CNA Reminder

CNA Reminder

242 - Orange (4th segment) slow flash

362 - RN Reminder

RN Reminder

243 - Green (4th segment) slow flash

363 - Aide Round

Aide Round

241 - Yellow (4th segment) slow flash

364 - CNA Round

CNA Round

242 - Orange (4th segment) slow flash

365 - RN Round

RN Round

243 - Green (4th segment) slow flash

710 - Console Call

Console Call

58 -White (1st segment)

White (3rd&4th segment)

60 - White (1st segment) slow flash

Pink (1st segment) slow flash

720 - Cordout Left Bed

Cordout

Š 2013 Jeron Electronic Systems Inc.

Urgent

4-31

Peripheral P Bus Stations

System Planning

Light Show # Dome/Zone Light 7952/7962/7972 6 LED

Nurse Console Call Type/Event/Priority # Display Message

4-32

Call Status LED & Alert Tone

Dome/Zone Light 7953, 7963, 7973 Prism

Visual Signals

722 - Cordout Right Bed

Cordout

61 - White (1st segment) slow flash

Pink (2nd segment) slow flash

730 - Bed Out Left Bed

Bed Out

65 - White (1st segment) slow flash

Pink (1st segment) slow flash

732 - Bed Out Right Bed

Bed Out

Urgent

White (1st segment)

Pink (2nd segment)

745 - Aide Badge

100 - Red (2nd segment) fast flash

Red (3rd & 4th segment) medium flash

746 - CNA Badge

100 - Red (2nd segment) fast flash

Red (3rd & 4th segment) medium flash

747 - RN Badge

100 - Red (2nd segment) fast flash

Red (3rd & 4th segment) medium flash

768 - OT Bed Siderail Left Bed

70 - White (1st segment) fast flash

White (1st segment) medium flash

769 - OT Bed Siderail Right Bed

71 - White (1st segment) fast flash

White (2nd segment) medium flash

770 - OT Normal -Left

OT Normal

70 - White (1st segment) fast flash

White (1st segment) medium flash

772 - OT Normal - Right

OT Normal

71 - White (1st segment) fast flash

White (2nd segment) medium flash

780 - OT Staff

OT Staff

67 - White (1st segment) medium flash

White (3rd&4th segment) medium flash

790 - OT Pers Att - Left

OT Pers Att

70 - White (1st segment) fast flash

White (1st segment) medium flash

792 - OT Pers Att - Right

OT Pers Att

71 - White (1st segment) fast flash

White (2nd segment) medium flash

800 - OT Console

OT Console

68 - White (1st segment) medium flash

White (3rd & 4th segment) medium flash

810 - OT Cordout Left Bed

OT Cordout

75 - Alt. White (1st segment) & Red (2nd)

Pink (1st) medium flash

812 - OT Cordout Right Bed

OT Cordout

76 - Alt. White (1st segment) & Red (2nd)

Pink (2nd) medium flash

815 - OT Bed Out Left Bed

OT Bed Out

80 - Red (2nd segment) medium flash

Pink (1st segment) medium flash

817 - OT Bed Out Right Bed

OT Bed Out

81 - Red (2nd segment) medium flash

Pink (2nd segment) medium flash

820 - Bed Exit Left Bed

Bed Exit

85 - Red (2nd segment) medium flash

Magenta (1st segment) medium flash

822 - Bed Exit Right Bed

Bed Exit

86 - Red (2nd segment) medium flash

Magenta (2nd segment) medium flash

830 - Bath Assist

Bath Assist

90 - Red (2nd segment) medium flash

Red (3rd&4th segment)

840 - Shower

Shower

92 - Red (2nd segment) medium flash

Red (3rd&4th segment)

846 - IV Pump

IV Pump

94 - Red (2nd segment) medium flash

Red (3rd&4th segment)

847 - Alarm

Alarm

94 - Red (2nd segment) medium flash

Red (3rd&4th segment)

848 - Alarm 1

Alarm 1

94 - Red (2nd segment) medium flash

Red (3rd&4th segment)

849 - Alarm 2

Alarm 2

94 - Red (2nd segment) medium flash

Red (3rd&4th segment)

Š 2013 Jeron Electronic Systems Inc.

System Planning

Peripheral P Bus Stations

Light Show # Dome/Zone Light 7952/7962/7972 6 LED

Nurse Console Call Type/Event/Priority # Display Message

Call Status LED & Alert Tone

Dome/Zone Light 7953, 7963, 7973 Prism

Visual Signals

850 - Help

Help

94 - Red (2nd segment) med. flash

Red (3rd & 4th segment)

852 - Pulse OX

Pulse OX

94 - Red (2nd) med. fl.

Red (3rd&4th)

853 - Vent

Vent

94 - Red (2nd) med. fl.

Red (3rd&4th)

860 - Priority Left Bed

Priority

95 - White (1st) medium flash

862 - Priority Right Bed

Priority

96 -White (1st)

White (2nd)

870 - OT Bath Assist

OT Bath Assist

100 - Red (2nd) fast fl.

Red (3rd&4th) med. flash

880 - OT Shower

OT Shower

102 - Red (2nd) fast fl.

Red (3rd&4th) med. flash

890 - OT Help

OT Help

104 - Red (2nd) fast fl.

Red (3rd&4th) med. flash

900 - OT Priority Left Bed

OT Priority

120 - White (1st) fast fl.

902 - OT Priority Right Bed

OT Priority

121 -White (1st) fast fl.

910 - Urgent Left Bed

Urgent

125 - White (1st) fast fl.

Magenta (1st) fast fl.

912 - Urgent Right Bed

Urgent

126 - White (1st) fast fl.

Magenta (2nd) fast fl.

920 - Urgent Bath

Urgent Bath

130 - Red (2nd) fast fl.

Alt. Red & Yellow (3rd&4th) fast fl.

930 - OT Aide Reminder

OT Aide Reminder

Urgent

White (2nd) fast fl.

245 - Yellow (4th segment)fast flash

931 - OT CNA Reminder

OT CNA Reminder

246 - Orange (4th segment) fast flash

932 - OT RN Reminder

OT RN Reminder

247 - Green (4th segment) fast flash

933 - OT Aide Round

OT Aide Round

245 - Yellow (4th segment) fast flash

934 - OT CNA Round

OT CNA Round

246 - Orange (4th segment) fast flash

935 - OT RN Round

OT RN Round

247 - Green (4th segment) fast flash

936 - OT Aide Request

OT Aide Request

245 - Yellow (4th segment) fast flash

937 - OT CNA Request

OT CNA Request

246 - Orange (4th segment) fast flash

938 - OT RN Request

OT RN Request

247 - Green (4th segment) fast flash

950 - Low Battery

Low Battery

952 - Trouble

Trouble

954 - Console Fail

Console Fail

956 - Con Cont Fail

Con Cont Fail

958 - Power Fail

Power Fail

960 - Gateway Fail

Gateway Fail

1008 - Bath Emer

Bath Emer

1010 - Staff Emer

Staff Emer

1012 - Fire

130 - Red (2nd segment) fast flash

Alt. Red&Yellow (3rd&4th segments) fast flash

200 - Red (2nd segment) fast flash

Red (all 4) fast flash

Fire

219 - Alt. White (1st) & Red (2nd) fast flash

Alt. Red & Yellow (all 4) fast flash

1020 - Code

Code

220 - Blue (3rd segment) fast flash

Alt. Blue in sequence (all 4) fast flash

1021 - Code Pink

Code Pink

221 - Alt. Red (2nd) & Blue (3rd) fast flash

Alt. Pink in sequence (all 4) fast flash

1023 - Code Blue

Code Blue

224 - Blue (3rd segment) fast flash

Alt. Blue in sequence (all 4) fast flash

© 2013 Jeron Electronic Systems Inc.

Emergency

Code

4-33

Patient Room Equipment

System Planning

Patient Room Equipment Pillow Speakers for DIN Jack Patient Stations Pillow speakers plug into the patient station DIN jacks and provide the patient with the ability to place a call to the Nurse Console and communicate with the staff members. Pillow speakers also control patient TV entertainment. TV must be UL hospital grade digital control. Jeron offers five types of pillow speakers described below.

Model 7901 Standard Pillow Speaker Used for controlling patient TV entertainment, and both signaling and communicating with staff.

Figure 4.26: Model 7901 Standard Pillow Speaker Dimensions (H x W x D)

8.4 x 3 x 1.25 in. (21.3 x 7.6 x 3 cm)

Cord and Connector

10 ft. (3 m) white vinyl cord, electrostatic discharge (ESD) protected with 8-pin plug

Case

Flame-retardant ABS plastic

Controls/Indicators

1 – Nurse CALL button 1 – TV power 2 – Channel Up/Down arrows 2 – Volume High/Low arrows 1 – Closed Captioning 1 – Mute 1 – Sleep 1 – Option

Speaker/Microphone

2.25 in. (5.7 cm) round with Alnico magnet; 45 Ohm; 1/4 watt; Frequency response 500 to 4500 Hz minimum

Table 4.30: 7901 Technical Data

4-34

© 2013 Jeron Electronic Systems Inc.

System Planning

Patient Room Equipment

Model 7902 Standard Pillow Speaker with Two Aux Buttons Used for controlling patient TV entertainment, both signaling and communicating with staff, and optionally controlling room lighting. Equipped with two additional auxiliary buttons.

Figure 4.27: Model 7902 Standard Pillow Speaker with Two Auxiliary Buttons Dimensions (H x W x D)

8.4 x 3 x 1.25 in. (21.3 x 7.6 x 3 cm)

Cord and Connector

10 ft. (3 m) white vinyl cord, electrostatic discharge (ESD) protected with 8-pin plug

Case

Flame-retardant ABS plastic

Controls/Indicators

1 – Nurse CALL button 1 – TV power button 2 – Channel Up/Down arrows buttons 2 – Volume High/Low arrows buttons 1 – Closed Captioning button 1 – Mute button 1 – Sleep button 1 – Option button 2 – Auxiliary buttons

Speaker/Microphone

2.25 in. (5.7 cm) round with Alnico magnet; 45 Ohm; 1/4 watt; Frequency response 500 to 4500 Hz minimum

Table 4.31: 7902 Technical Data

© 2013 Jeron Electronic Systems Inc.

4-35

Patient Room Equipment

System Planning

Model 7903 Direct Access Pillow Speaker Used the for controlling patient TV entertainment, both signaling and communicating with staff. Includes a channel keypad.

Figure 4.28: Model 7903 Direct Access Pillow Speaker

Dimensions (H x W x D)

8.4 x 3 x 1.25 in. (21.3 x 7.6 x 3 cm)

Cord and Connector

10 ft. (3 m) white vinyl cord, electrostatic discharge (ESD) protected with 8-pin plug

Case

Flame-retardant ABS plastic

Controls/Indicators

1 – Nurse call button 1 – TV Power 1 – Closed Captioning button 10 – Channel Keypad buttons 1 – Mute button 2 – Volume High/Low arrow buttons 2 – Channel Up/Down arrow buttons 1 – Previous Channel button 1 – Sleep button 1 – Option button

Speaker/Microphone

2.25 in. (5.7 cm) round with Alnico magnet; 45 Ohm; 1/4 watt; Frequency response 500 to 4500 Hz minimum

Table 4.32: 7903 Technical Data

4-36

© 2013 Jeron Electronic Systems Inc.

System Planning

Patient Room Equipment

Model 7904 Direct Access Pillow Speaker with Two Aux Buttons Used for controlling patient TV entertainment, both signaling and communicating with staff, and optionally controlling room lighting. Equipped with a keypad and two additional auxiliary buttons.

Figure 4.29: Model 7904 Direct Access Pillow Speaker with Two Auxiliary Buttons

Dimensions (H x W x D)

8.4 x 3 x 1.25 in. (21.3 x 7.6 x 3 cm)

Cord and Connector

10 ft. (3 m) white vinyl cord, electrostatic discharge (ESD) protected with 8-pin plug

Case

Flame-retardant ABS plastic

Controls/Indicators

1 – Nurse call button 1 – TV Power 1 – Closed Captioning button 10 – Channel Keypad buttons 1 – Mute button 2 – Volume High/Low arrow buttons 2 – Channel Up/Down arrow buttons 1 – Previous Channel button 1 – Sleep button 1 – Option button 2 – Auxiliary buttons

Speaker/Microphone

2.25 in. (5.7 cm) round with Alnico magnet; 45 Ohm; 1/4 watt; Frequency response 500 to 4500 Hz minimum

Table 4.33: 7904 Technical Data

© 2013 Jeron Electronic Systems Inc.

4-37

Patient Room Equipment

System Planning

Model 7905 Enhanced Pillow Speaker Used for controlling patient TV entertainment, both signaling and communicating with staff, and controlling room lighting. In addition to the call button, the pillow speaker provides three call buttons that are clearly marked with the texts WATER, PAIN and TOILET for specific requests from nurse and equipped with call placed LED indicators. Pillow speaker is also equipped with two auxiliary buttons and a microphone for full duplex audio.

Note: Pillow speaker microphone active only when used with Model 7923 or 7924.

Figure 4.30: Model 7905 Enhanced Pillow Speaker Dimensions (H x W x D)

8.4 x 3 x 1.25 in. (21.3 x 7.6 x 3 cm)

Cord and Connector

10 ft. (3 m) white vinyl cord, electrostatic discharge (ESD) protected with 8-pin plug

Case

Flame-retardant ABS plastic

Controls/Indicators

1 – Nurse call button 1 – Toilet button w/ LED 1 – Water button w/ LED 1 – Pain button w/ LED 1 – TV Power 1 – Closed Captioning button 10 – Channel Keypad buttons 1 – Mute button 2 – Volume High/Low arrow buttons 2 – Channel Up/Down arrow buttons 1 – Previous Channel button 1 – Sleep button 1 – Option button 2 – Auxiliary buttons 1 – Microphone

Speaker/Microphone

2.25 in. (5.7 cm) round with Alnico magnet; 45 Ohm; 1/4 watt; Frequency response 500 to 4500 Hz minimum

Figure 4.31: 7905 Technical Data

4-38

© 2013 Jeron Electronic Systems Inc.

System Planning

Patient Room Equipment

Associated Equipment for Pillow Speakers Equipment

Purpose Pillow speakers connect to the DIN jacks on the patient stations to enable patient to call the nurse for assistance and controls TV entertainment.

Model 7905 Enhanced Pillow Speakers may be used with nonmuting patient stations (Models 7920, 7922, 7925, and 7926) to take advantage of the dedicated nurse call buttons (Nurse, Water, Pain, and Toilet) and auxiliary controls only. Nurse call audio will be routed through the pillow speaker only when used in conjunction with muting patient stations 7923 and 7924.

Patient Station

7906 Pillow Speaker Auxiliary Output Module

Required for pillow speakers with auxiliary buttons Models 7902, 7904, and 7905

Table 4.34: Pillow Speakers Associated Equipment

Model 7906 Pillow Speaker Auxiliary Output Module Required for the use of the lighting control buttons on the Direct Access Digital Pillow Speakers, Models 7902, 7904, and 7905.

Light Controllers The light controller option (yellow auxiliary buttons) on Model 7902, 7904 and 7905 Pillow Speakers allow a patient to control room lighting using the provided one or two buttons on the pillow speaker.

The back of a patient stations is equipped with an IDC header that requires the connection of a model 7906 Pillow Speaker Auxiliary Output Module.

Model 7906 then connects to the lighting control relay provided by others.

Figure 4.32: Model 7906 Pillow Speaker Auxiliary Output Module Enclosure

Shrink wrapped housing

Dimensions (H x W x D)

0.7 x 1.3 x 0.4 in. (1.7 x 3.3 x 1 cm)

Back box Required

Same as associated Patient Station

Connector to Patient Stations

1 - IDC Connector

Electrical Rating

5VDC

Table 4.35: 7906 Technical Data

Š 2013 Jeron Electronic Systems Inc.

4-39

Patient Room Equipment

System Planning

Callcord(s) for DIN Jack Patient Stations Callcords plug into patient station DIN jacks and enable patient to place a call to nurse for assistance. Callcords are safe for use in oxygen enriched atmosphere.

Model 7908 Sealed Callcord Sealed design allows complete submersion for sterilization.

Figure 4.33: Model 7908 Sealed Callcord

Pendant and Cord

White molded thermoplastic pendant with white vinyl cord, electrostatic discharge (ESD) protection

Controls/Indicators

1 - Low ambient light LED 1 - Nurse CALL button

Connector

8-pin plug; Molded plastic shell

Cord Length

10 ft. (3 m)

Table 4.36: 7908 Technical Data

Model 7909/7910 Callcord Used to signal for a nurse from an associated patient station.

Figure 4.34: Model 7909/7910 Callcord

Pendant and Cord

White molded thermoplastic pendant with white vinyl cord, electrostatic discharge (ESD) protection

Cord Lengths

7909—6 ft. (1.8 m) 7910—10 ft. (3 m)

Controls

Nurse CALL button

Connector

8-pin plug; Molded plastic shell

Table 4.37: 7909/7910 Technical Data

4-40

© 2013 Jeron Electronic Systems Inc.

System Planning

Patient Room Equipment

Model 7913 Callcord Adapter, 1/4”-to-DIN Used to connect third party callcord devices to patient stations DIN jack.

Figure 4.35: Model 7913 Callcord Adapter

Connections

8-pin DIN to 1/4” call jack

Table 4.38: 7913 Technical Data

Model 7914 Geriatric Callcord Provide a means of signaling for assistance with only slight hand or body pressure. Geriatric Callcords are used in hospitals and nursing homes for geriatric or pediatric patients, for feeble or disabled patients, for complete safety in an oxygen-enriched environment, or for use in showers.

Figure 4.36: Model 7914 Geriatric Callcord Bulb & Cord

6 ft. (1.8 m) Gray non-toxic tubing with matching molded air bulb

Controls

Air Bulb; pressure activated

Connector

8-pin plug; molded plastic shell

Table 4.39: 7914 Technical Data

Model 8839 Breath Activated Callcord Provide a means of signaling for assistance by fully disabled patients who cannot operate a conventional callcord by pressing a button or squeezing a bulb. Breath Activated Callcords offer complete safety in an oxygen-enriched environment.

Requires use of 7913 Callcord Adapter to convert 1/4” jack into a DIN jack.

© 2013 Jeron Electronic Systems Inc.

4-41

Patient Room Equipment

System Planning

Figure 4.37: Breath Activated Call Cord

Conduit & Cord

Plastic covered, 3’ heavy duty flexible metal conduit and 9’ x 5/16” diameter gray plastic tubing

Controls

Vinyl straw; breath activated

Connector

1/4” call jack for 7913 adapter

Table 4.40: 8839 Technical Data

Associated Equipment for Callcords Equipment

Purpose

Patient Station

Connects to the DIN jacks on the patient stations to enable patient to call the nurse for assistance

Table 4.41: Callcord Associated Equipment

4-42

© 2013 Jeron Electronic Systems Inc.

Chapter 5: Consoles & Terminals

.

System Planning

Call Center M Bus Stations

Call Center M Bus Stations

M BUS

Workflow Terminal

Nurse Console

M Bus devices include the Nurse Console, Workflow Terminal, Staff Duty Terminal, and Nurse Terminal. Each device connects to a Console Controller (dome or domeless) on the M Bus port.

Nurse Consoles are located at nurse stations and are used as the primary call center in the facility. The Nurse Console annunciates calls from patient and staff stations, enable the staff to answer the calls and communicate with patient or staff, place calls, set service requests, page staff, and view staff location. The touchscreen Nurse Terminal provides all the functionality of the Nurse Console but without the handset. Allows for bi-directional nonprivate audio communication via speaker.

In addition to offering full Nurse Console functionality, a Workflow Terminal (M Bus) also helps manage workflow, rounding and service requests, places calls, and offers intercom communication options in a patient room.

Staff area options include duty, staff/duty and staff stations with audio. A Staff Duty Terminal may be used to annunciate calls and provide audio communication in areas where staff congregate, such as a utility room, break room, or lounge. The Staff Duty Terminal displays large graphic call priority indicators that show active calls within the coverage area of the Staff Duty Terminal grouped by Routine, Urgent, Emergency, and Code.

Model 7965 Color Touchscreen Nurse Console The touchscreen Nurse Consoles are used as the primary interface among users of the system and provide full duplex two-way voice communication with the use of a handset between staff and patients or staff members. The consoles are used to place, receive, display, and answer calls from patients and staff and are typically located in areas where staff congregate and need to communicate with patients and fellow staff members, such as nurse stations, work stations, centralized communication centers, or any area where staff receive calls. A 5.7� touch-sensitive flat panel screen displays calls in the system in the order of call priority.

Š 2013 Jeron Electronic Systems Inc.

5-1

Call Center M Bus Stations

System Planning

Functions The attendant at the Nurse Console has the following options, among others: •

Answer calls from patient/staff or originate calls to stations

•

Page, monitor, locate and dispatch staff/aides

•

Set service requirements, rounding, reminders

•

Review service needs, bed privacy/priority status

•

Change bed status

•

Transfer control from other consoles

•

Adjust talk/listen volume settings for each individual patient/staff intercom station

Nurse Console functions include setting/reviewing up to four levels of service requirements, day/night tones, tone mute with regeneration, staff locating by one of up to three levels or optionally by staff name, swing rooms, unit transfer, console to console intercom, and audio paging. Call coverage and available features are programmed on an individual console basis allowing each console to be customized for its specific purpose and location.

The Nurse Console display offers three difference screen modes: Standard, “Zoom Out” and “Zoom In”. In Standard view mode, up to four calls may be displayed simultaneously. In “Zoom Out” mode, up to 30 calls may be displayed simultaneously. In the “Zoom In” mode, up to two calls may be display simultaneously and are readily visible from several feet away. If more calls are queued at the Nurse Console than can be displayed, the highest priority and/or longest waiting calls will display first with the ability to scroll to view the additional calls. Over 1,000 unique call priorities are available on the system with the ability to customize each call priority’s call-in tone or voice prompt. Calls may be answered using the handset for semi-private duplextwo way voice communication or via the panel speaker for no privacy.

Figure 5.1: Model 7965 Nurse Console

5-2

© 2013 Jeron Electronic Systems Inc.

System Planning

Call Center M Bus Stations

Dimensions

8.3 x 9.15 x 3.0 in. (21 x 24.1 x 7.6 cm) Footprint: 75.9 in² (489 cm²)

Display

Backlit 5.7 inch (14.5 cm), 320 x 240 resolution color touchscreen

Speaker

2.75” (7 CM); 8 Ohm

Microphone

Electret

Control Keys (4)

Home, Answer/Push-to-Talk, Cancel, Tone Mute

Electrical Rating

40V @ 5.8 W

Terminations

1 - RJ-45 for Cat-5 cable to Console Controller

Figure 5.2: 7965 Technical Data

Associated Equipment for Nurse Consoles Note: Consoles may be surface mounted on an attached 45 degree base or wall mounted on a wall bracket.

Equipment

Purpose

Back box

To mount the console on the wall, use two-gang backbox with a two-gang trim ring. “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Model 9769 Wall Bracket

To mount the console to the wall

Model 7969 Wall Jack

To connect desk mounted console to Console Controller

Cat-6 Cable

To connect console to Console Controller

Console Controller

Provides power, signaling, and audio for an associated Nurse Console

Table 5.1: 7965 Associated Equipment

Model 7967-P Color Touchscreen Workflow Terminal in Patient Rooms Touchscreen Workflow Terminals (Model 7967-P) are used in patient rooms by staff to provide workflow management. The Workflow Terminal also for staff sign-in to access master display mode for the ability to answer calls and initiate staff-to-staff and staff-to-patient communications.

The Workflow Terminal touchscreen touchpoints enable staff to initiate onetouch workflow requests for procedures, housekeeping, transport, or any number of system customizable workflow events. Touchpoints can also be configured to place calls, set service requirements, request team member assistance, set reminders, and confirm staff rounding. Touchpoint placement, size, and operation is configurable at system configuration and can be customized on a per Workflow Terminal basis.

The Workflow Terminal connects to a Console Controller (one per terminal) on the M Bus port via Cat-6 cable.

Workflow Terminal use requires Jeron Model 7980 Staff Assignment & Messaging Software.

© 2013 Jeron Electronic Systems Inc.

5-3

Call Center M Bus Stations

System Planning

Figure 5.3: Workflow Terminal (Model 7967-P)

Dimensions

(H x W x D): 8.3” x 6.8” x 1.8” (21 x 17.2 x 4.5 cm) Wall mount; footprint 56.4 in2 (364 cm2)

Display

5.7” (14.5 cm), 320 x 240 resolution color touchscreen

Speaker

2.75” (7 CM); 8 Ohm

Microphone

Electret

Control Keys (4)

Home, Answer/Push-to-Talk, Cancel, Tone Mute

Electrical Rating

40V @ 5.8 W

Terminations

1 – RJ45

Table 5.2: 7967-P Technical Data

Associated Equipment for Workflow Terminal Equipment

Purpose

Back box

To mount the console on the wall, use two-gang backbox with a two-gang trim ring. “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Model 9769 Wall Bracket

To mount the console to the wall

Cat-5 (minimum) Cable

To connect console to Console Controller

Console Controller (model 7960)

Provides power, signaling, and audio for an associated terminal

7980 Staff Assignment & Messaging Software

Provides the ability to log in staff with passwords via staff IDs assigned in 7980

Table 5.3: 7967-P Associated Equipment

5-4

© 2013 Jeron Electronic Systems Inc.

System Planning

Call Center M Bus Stations

Model 7967-S Color Touchscreen Staff Duty Terminals in Staff Areas The Touchscreen Staff Duty Terminal (Model 7967-S) is used to annunciate calls and provide audio communication in areas where staff may congregate, such as a utility room or lounge.

The Staff Duty Terminal’s touchscreen display includes large graphic call priority indicators that show active calls within the duty area of the Staff Duty Terminal grouped by Routine, Urgent, Emergency, and Code. Up to four call indicators may be active at the same time while the Terminal audibly annunciates call tones or voice prompts for the highest active call priority. For active calls, staff can selectively mute the call tones/voice prompts at the Terminal while the visual annunciation will continue until the call is cleared; the call tones/voice prompts will regenerate with any subsequent calls.

The Staff Duty Terminal allows attendant to answer calls and initiate staff-tostaff and staff-to-patient communications.

The screen also includes a large clock display that is readily visible from a distance. The displayed time is synchronized to the facility’s network time and shared among all Nurse Consoles and Staff Duty Terminals on the Provider 790 system.

The terminal connects to a Console Controller (one per terminal) on the M Bus port via Cat-6 cable.

Figure 5.4: Staff Duty Terminal (Model 7967-S)

Dimensions

(H x W x D): 8.3” x 6.8” x 1.8” (21 x 17.2 x 4.5 cm) Wall mount; footprint 56.4 in2 (364 cm2)

Display

5.7” (14.5 cm), 320 x 240 resolution color touchscreen

Speaker

2.75” (7 CM); 8 Ohm

Microphone

Electret

Control Keys (4)

Home, Answer/Push-to-Talk, Cancel, Tone Mute

Electrical Rating

40V @ 5.8 W

Terminations

1 – RJ45

Table 5.4: 7967-S Technical Data

© 2013 Jeron Electronic Systems Inc.

5-5

Call Center M Bus Stations

System Planning

Associated Equipment for Staff Duty Terminal Equipment

Purpose

Back box

To mount the console on the wall, use two-gang backbox with a two-gang trim ring. “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Model 9769 Wall Bracket

To mount the console to the wall

Cat-5 (minimum) Cable

To connect console to Console Controller

Console Controller (model 7960)

Provides power, signaling, and audio for an associated terminal

Figure 5.5: 7967-S Associated Equipment

Model 7967-M Color Touchscreen Nurse Terminals in Staff Areas The Touchscreen Nurse Terminal (Model 7967-M) is used to annunciate calls and provide audio communication in areas where staff may congregate, such as a utility room or lounge.

The Nurse Terminal is used to place, receive, display, and answer calls from patients and staff, providing bi-directional nonprivate audio communication between rooms or other terminals via terminal speaker. The touchscreen displays calls in the system in the order of call priority. It graphically displays incoming calls including patient or staff station calling room number, bed (if applicable), call priority, elapsed time of call, and optionally the patient’s name, gender, acuity, and other relevant patient information.

The Nurse Terminal provides all the functionality of the Nurse Console (Model 7965), including the ability to: •

Page staff manually, including staff selection, tag selection, free text

•

Send service requests to staff

•

Set rounding or reminders

•

Upgrade call priority

•

Change call status for callcord calls and feature bed calls

•

Display multiple calls on a 2-call screen, 4-call screen or up to 30-call screen

•

Use the Volume touchpoint to adjust alert tone and console volume

The Nurse Terminal connects to a Console Controller (one per terminal) on the M Bus port via Cat-6 cable.

5-6

© 2013 Jeron Electronic Systems Inc.

System Planning

Call Center M Bus Stations

Figure 5.6: Nurse Terminal (Model 7967-M)

Dimensions

(H x W x D): 8.3” x 6.8” x 1.8” (21 x 17.2 x 4.5 cm) Wall mount; footprint 56.4 in2 (364 cm2)

Display

5.7” (14.5 cm), 320 x 240 resolution color touchscreen

Speaker

2.75” (7 CM); 8 Ohm

Microphone

Electret

Control Keys (4)

Home, Answer/Push-to-Talk, Cancel, Tone Mute

Electrical Rating

40V @ 5.8 W

Terminations

1 – RJ45

Table 5.5: 7967-M Technical Data

Associated Equipment for Nurse Terminal Equipment

Purpose

Back box

To mount the terminal on the wall, use two-gang backbox with a two-gang trim ring. “Backboxes, Mounting Racks & Wall Cabinets” on page 8-1

Model 9769 Wall Bracket

To mount the terminal to the wall

Cat-5 (minimum) Cable

To connect terminal to Console Controller

Console Controller (model 7960)

Provides power, signaling, and audio for an associated terminal

Figure 5.7: 7967-M Associated Equipment

© 2013 Jeron Electronic Systems Inc.

5-7

Call Center M Bus Stations

5-8

System Planning

Š 2013 Jeron Electronic Systems Inc.

Chapter 6: System Wiring

.

System Planning

Installation and Wiring

Installation and Wiring The Provider 790 system’s wiring strategy allows stations of the same type in a room to connect in series to a Room Controller. Audio stations connect via Cat 5/5e/6 cable. Peripheral stations connect in series to a Room Controller via single 22 AWG UTP cable.

Observe the following precautions and specifications when planning system installation.

Equipment Protection Precaution The Provider 790 Nurse Call System equipment contains low power microprocessor circuits which are sensitive to electrostatic discharge (ESD).

Always observe the following precautions: 1. Do not remove bus stations from their static protective bags until they are ready for installation. You should be grounded using an ESD wrist strap when handling these units. Use only Jeron furnished mounting hardware.

2. Observe the same precautions whenever a Nurse Console is opened for inspection or maintenance.

To avoid static charge: 1. Make sure callcords and patient stations are not close to or touching the metal bed frame or attendant when sheets are changed, as high levels of ESD are produced from this act.

2. Install the system in a continuous metallic conduit and backbox. Such systems are more resistant to failure due to static discharge or electrical disturbance in general.

3. Attach the green ground wire clip on patient stations to the grounded backbox.

Installation Precautions for Patient and Staff Safety Patient and staff safety depends on the following installation precautions: •

•

Note: Only the Model 7958 Pullcord/ Pushbutton Shower Station is waterresistant with wall gasket kit.

All installer-provided lighting or entertainment control relays (operated via pillow speakers) must have proper surge protection added to the coils to damp the voltage transients (back EMF) created by the relay coils.

The system wiring must be isolated from earth grounds and from other AC powered devices in order to protect patients and staff from ground faults and leakage currents. Some therapies may greatly increase patient risk from ground faults. Keep all system conductors and grounds separate from earth grounds and carefully test to ensure that ancillary equipment does not contribute leakage current to the system.

Pillow Speakers are not approved for use in oxygen enriched environments as defined by UL 1069. Where oxygen use or electrical susceptibility (see above) mandates non-electrical patient control devices, use the callcords.

© 2013 Jeron Electronic Systems Inc.

6-1

Installation and Wiring

System Planning

Planning System Wiring 1. Obtain floor plans or blueprints to verify the locations of each station type.

If they are not documented on the floor plans, conduct a site survey to determine the final locations.

2. Prepare a complete equipment list from architectural plans and specifications. Additional surveys may be required to develop sufficient information to plan an effective installation, i.e. wire runs, location of the Gateways, room numbering systems, coverage areas, zone and duty station memberships, etc.

All stations are mounted in backboxes. The table on page 8-1 lists the recommended backbox types and covers for each station. Use only UL Listed backboxes.

Wiring Precautions •

Wire all systems in accordance with local building codes, using the wiring diagrams in the Provider 790 Installation Manual.

•

Use the exact wire type specified; use of any other kind may degrade or disable system performance.

•

Do not run system wiring in common conduit or in close proximity (12 inches minimum) with wiring for other systems (AC power distribution, fire alarm, entertainment or P.A. systems, etc.). Alternatively, use a solid divider in the cable tray to isolate the system wires.

•

Verify that all wiring is free of shorts and earth grounds.

•

All field wiring, power, data and audio is isolated from earth ground, chassis ground, and building ground.

Bus Types & Cables J Bus •

Main corridor trunk cable for all controllers (room/console/zone)

•

Cat-6 (23 AWG) cable connects 9779 splitters in series to a Gateway.

End of line termination resistor plug (Model 9778) must be installed on last J Bus 9779 splitter. RJ-45 connectors are used

•

Factory furnished 6 inch, plug-ended cables connect room controllers to 9779 splitters. Controllers must be connected to 9779 splitters

•

Cat-6 (23 AWG) cable must be wired according to T568B standard.

The J Bus run must be continuous with no t-taps or any bridged taps

•

Max. 700’ from Gateway to last Controller

Gateways/Switches

6-2

•

Cat-5/5e/6 cable connects Gateways to Nurse Call Isolated 8 Port Ethernet Switch. RJ-45 connectors are used

•

Cat-5/5e/6 cable connects Nurse Call Isolated 8 Port Ethernet Switches. RJ-45 connectors are used

© 2013 Jeron Electronic Systems Inc.

System Planning

Installation and Wiring

•

Max. 328’ from Gateway to Switch

•

Max. 328’ from one Switch to another Switch

•

Two 62.5/125 µm multi-mode optical fibers connect 7991-FX switches up to 2km apart

R Bus •

In-room cable for patient stations (audio stations, duty & electrical supervision stations)

•

Cat-5/5e/6 cable connects audio stations in a room in series to a room controller. RJ-45 connectors are used

•

Max. 100’ total R Bus cable per room

P Bus •

In-room wire pair for peripheral (non-audio) stations (bath, code)

•

One 22 AWG twisted pair wire connects peripheral stations in series to a Room Controller. Screw terminals are used

•

Max. 100’ total P Bus cable per room

M Bus •

Cable for Nurse Console, Workflow Terminal, Staff Duty Terminal, or Nurse Terminal

•

Cat-6 cable connects one Nurse Console/Workflow Terminal/Staff Duty Terminal/Nurse Terminal to one Console Controller. RJ-45 connectors are used

•

Desk mounted Nurse Console usually connects to a Console Controller via the Nurse Console wall jack

•

Max. 700’ between Console Controller and connected device, provided the associated controller is equipped with dedicated power splitter to ensure J Bus voltage at the controller is adequate

Cat-5/6 Cable Standard Cat-5/6 cable must be wired according to T568B standard.

© 2013 Jeron Electronic Systems Inc.

6-3

6-4

Staff/Duty 7927

SD

RCD RCD

P

SE

P

Patient Room

Code Blue 7949 Staff Emergency 7930

CB

Cable Type

SE

Bath 7932

B

CB

SE

NC

Nurse Console 7965

NURSE CONSOLE/STAFF TERMINAL – M BUS

Staff Lounge

PERIPHERAL STATIONS ( NON AUDIO) – P BUS

SD

RC

One 22 AWG Twisted( Pair) P Bus Cat-6 23 AWG (J Bus or M Bus) Cat-5/5e/6 (R Bus) Cat-5/6 Cable Wired According to T568B Standard

Patient 7920-7926

P

AUDIO STATIONS – R BUS

CB

Patient Room

RCD

B

CB

OR

Room Controller (Domeless) 7950 RC

ZL

RCD

CB

P

RCD RCD

RCD

P

MC

NC

Zone Lights 7971-7973

Room Controller w/Dome Light 7951-7953

CONTROLLERS, ZONE LIGHTS – J Bus

Console Controller (Zoneless) 7960

Exam

CB

SE

B

Patient Room

MC

RCD RCD

Maximum distance of 700 ft. from Gateway to last Device on the J Bus Corridor Bus run (Cat-6 Cable) must be continuous with no t-taps or bridged taps

Utility Room

POWER SUPPLY

GATEWAY

Termination Resistor (Model 9778)

ZL

9779 Splitter

RCD RCD

P

SE

P

B

P

B

P

Patient Room

NURSE STATION

790 System Wiring Diagrams System Planning

790 System Wiring Diagrams

Typical Floor Wiring

Figure 6.1: Typical Floor Wiring

© 2013 Jeron Electronic Systems Inc.

© 2013 Jeron Electronic Systems Inc.

9779 J Bus Splitter 9779 J Bus Splitter

P

P

SE

MC

WT

MC

POWER SUPPLY POWER SUPPLY

GATEWAY GATEWAY

AUDIO STATIONS – R BUS

P

P P

P

CB

CB WT

MC

WT

MC RCD RCD RCD RCD

SD

SE

P

P

SE

P

P

SE

WT

Patient Room Patient Room

Cat-5/5e/6 Bus or or M R Bus) Cat-6 23 AWG(M (J Bus Bus) Cat-5/5e/6 (R Bus)

RC

CB

WT

NC

MC

WT

MC

MC

9777-2

B

CB

MC

OR

CB

OR

CB

P

P

RCD RCD RCD RCD

Cat-6 (for 9777 Splitter)

CONTROLLERS, ZONE LIGHTS – J Bus

RCD

P

RCD

P

CONTROLLERS, ZONE LIGHTS – J Bus

CB

SE

SE

9777-2

WT

CB

9777 Power Splitter

MC

WT

CB

MC

NC

NC

M Bus: Max. 700 ft. from Console Controller to Workflow Terminal/Nurse Console (Cat-6 cable), with dedicated power splitter

MC

NURSE STATION NURSE STATION

Note: For additional workflow Note: For additional terminals, consult workflow factory for terminals, consultrequirements. factory for power supply power supply requirements.

Console Controller (Zoneless) 7960 RCD Room Controller w/Dome Light 7951-7953 Console Controller (Zoneless) 7960 RCD Room Controller w/Dome Light 7951-7953 RC Zone Lights 7971-7973 Room Controller (Domeless) 7950 ZL Zone Lights 7971-7973 Room Controller (Domeless) 7950 ZL MC

B

Patient Room Patient Room

9777 Power Splitter

RCD

B

RCD

B

Exam Exam

RCD RCD RCD RCD

Nurse Console 7965 Workflow Terminal 7967-P RC Workflow Terminal 7967-P WT

NURSE CONSOLE/STAFF TERMINAL – M BUS NURSE CONSOLE/STAFF TERMINAL – MConsole BUS NC Nurse 7965

CB

SE

SE

One 22 AWG Twisted Pair (P Bus) Cat-5/6 Cable According T568B Standard OneWired 22 AWG TwistedtoPair (P Bus) Cat-5/6 Cable Wired According to T568B Standard

Staff Emergency 7930

B CBBathCode 7932Blue 7949 CB SECode Blue 7949 Staff Emergency 7930

RC

Staff Lounge Staff Lounge

PERIPHERAL STATIONS B Bath 7932 ( NON AUDIO) – P BUS

Cable Type Cable Type Cat-6 23 AWG (J Bus)

P Patient 7920-7926 Patient 7920-7926 SD Staff/Duty 7927 SD Staff/Duty 7927

SD

PERIPHERAL STATIONS ( NON AUDIO) – P BUS

Telecom Room Telecom Room

POWER SUPPLY

9777-1 9777-1

AUDIO STATIONS – R BUS

P

RCD RCD

RCD RCD

B

B

Patient Room Patient Room

Maximum distance of 700 ft. from Gateway to last device on the J Bus corridor Maximum distance of 700 ft. from Gateway to last device on the J Bus corridor Bus run (Cat-6 cable) must be continuous with no t-taps or bridged taps Bus run (Cat-6 cable) must be continuous with no t-taps or bridged taps

WT

B

B

Run in same conduit as Cat-6 J Bus

Termination Resistor (Model 9778) Termination Resistor (Model 9778)

ZL

ZL

P

P

SE

Patient Room Patient Room

System Planning 790 System Wiring Diagrams

790 Floor Wiring with 7967-P Workflow Terminals for Individual Patient Rooms

Figure 6.2: Alternate Floor Wiring Scenario with Touchscreen Workflow Terminals

6-5

790 System Wiring Diagrams

System Planning

Patient Room Typically, each patient room would have an associated Room Controller with dome light. Each Room Controller is assigned a room name (ID) that is shared by the stations in the room wired to the Controller. The inputs on patient stations differ only in their bed designators. Peripheral stations can be associated with a patient station in programming. Refer to Figure 6.3 for wiring.

Pullcord & Pushbutton Bath Station w/ Audio 7919 (R Bus)

Dual Auxiliary Alarm Input 6841 (Peripheral – P Bus)

Code 7949 (Peripheral – P Bus)

Patient Room A I

Patient BA Bathroom & Shower Shower Station 7958 (Peripheral – P Bus)

S

C B

P

C B

P

NOTE: From Controller

A Combined Total of 15 R Bus (audio) and P Bus (peripheral) Stations per Room Controller

RCD

To Next Controller

Maximum 100 ft. (30 m) to last Audio station Cat-5 Cable ( R Bus ) 22 AWG Wire Pair (P Bus) Cat-6 Cable (J Bus )

Patient 7920, 7923 (Audio – R Bus)

Room Controller with Dome Light 7951, 7952, 7953 (J Bus)

Figure 6.3: Typical Room Wiring

6-6

© 2013 Jeron Electronic Systems Inc.

System Planning

Š 2013 Jeron Electronic Systems Inc.

790 System Wiring Diagrams

6-7

790 System Wiring Diagrams

System Planning

Staff Area Where corridor lights are not necessary, such as staff areas, a domeless Room Controller is used. Refer to Figure 6.4. .

VD

Staff Lounge

Visual Duty Station 7917 (R Bus)

VD

9707 Splitter

SD Staff/Duty Station 7927 (Audio – R Bus)

RC To Next Controller

From Controller

NOTES A Combined Total of 15 R Bus (audio) and P Bus (peripheral) Stations per Room Controller Maximum 100 ft . ( 30 m ) from Controller to last audio station Model 7927 requires a dedicated Room Controller; may additionally connect up to three (3) 7917 Duty Stations

Room Controller (Domeless) 7950 (J Bus)

Cat-5 Cable ( R Bus) 22 AWG Wire Pair (P Bus) Cat-6 Cable (J Bus)

Figure 6.4: Typical Staff Lounge Wiring

6-8

Š 2013 Jeron Electronic Systems Inc.

System Planning

790 System Wiring Diagrams

Nurse Station The Nurse Console connects to a Console Controller. There is a limit of one Nurse Console per Console Controller. Console Controllers with Zone Lights are used if the dome lights in the hallway are not visible to the nurse at the station. Refer to Figure 6.5.

Additional Hallway Devices Zone Lights provide visual indications of calls for a room, group of rooms, corridor, unit, or up to an entire facility. They are installed in hallway intersections where dome lights may not be visible. They do not have any room station connections. Refer to Figure 6.5.

Controllers connect in hallways on a continuous J Bus run via splitters (using Cat-6 cables) to not disrupt system operation if a Controller is disconnected.

Maximum distance between Gateway to last controller: 700 ft.

From Controller/Zone Light

Nurse Station

ZL

MCZ

To Next Controller/Zone Light

Zone Light 7971, 7972, 7973 (J Bus)

NOTE: One Nurse Console/Terminal per Console Controller

Cat-6 Cable (J Bus) Cat-6 Cable (M Bus)

Console Controller with Zone Light 7961, 7962, 7963 (J Bus)

Nurse Console 7965 (M Bus)

Figure 6.5: Typical Nurse Station Wiring

Š 2013 Jeron Electronic Systems Inc.

6-9

Cable Requirements & Distances

System Planning

Cable Requirements & Distances Following is a summary of cable types and lengths according to device.

Central Equipment Gateways Model

7993/2

Function

Distributes power, data, and digital audio to J bus connected devices

Connection to

Cable Type

Maximum Distance

Nurse Call Isolated 8 Port Ethernet Switch with Uplink Port (Ports 1-8 - RJ45)

Cat-5/5e/6

328 ft.

(100 m)

All Controllers connect via 9779 splitter(s) - RJ45 Last splitter requires end-ofline terminating plug (P1)

Cat-6 (23 AWG)

To last Controller: 700 ft.

(213 m)

Power Supply w/Backup Battery

Factory furnished 30 inch cable Factory furnished 30 inch cable (40V power cable)

Nurse Call Isolated 8 Port Ethernet Switch with Uplink Port Model

7991

Model

7991FX

6-10

Function

Routes Ethernet data between Jeron Gateways

Function

Routes Ethernet data between Jeron Gateways

Connects to

Cable Type

Maximum Distance

Next Isolated 8 Port Ethernet Switch (RJ45)

Cat-5/5e/6

328 ft. (100 m)

Gateways (RJ45)

Cat-5/5e/6

328 ft. (100 m)

7995 Power Supply with Battery Backup

2 conductor 18 or 16 AWG

-

Bridge PC

Cat-5/5e/6

328 ft. (100 m)

Connects to

Cable Type

Maximum Distance

Next 7991-FX

62.5/125 Âľm multimode optical fiber (two required) terminated with duplex SC connector

1.24 mi. (2 km)

Š 2013 Jeron Electronic Systems Inc.

System Planning

Cable Requirements & Distances

Power Supply with Battery Backup Model

Function

Connects to

Cable Type

Maximum Distance

Gateway

7995

Switch (when not located next to a Gateway)

Powers connected nurse call devices

Supplemental Console Controllers on a single Gateway

Factory furnished 30 inch supervision cables Factory furnished 30 inch cable (40V power cable)

Controllers (J Bus) Console Controllers Model

Function

7960 7961 7962

Supply regulated power and provide data to connected Nurse Console or Terminal

7963

Connects to

Cable Type

Gateway and/or next Controller via 9779 Splitter (RJ45)

Factory furnished 6 inch cable

Nurse Console or Terminal (7960) (RJ45) *May connect via 7969 Console Wall Jack for desk mounted Nurse Console

Cat-6

Maximum Distance

700 ft. (213 m) max.

Room Controllers Model

Function

7950 7951 7952

Supply regulated power and provide data to connected audio and peripheral stations

Connects to

Cable Type

Gateway and/or next Controller via 9779 Splitter (RJ45)

Factory furnished 6 inch cable to 9779 splitter

Audio Station (RJ45)

Cat-5/5e/6

to last station: 100 ft.

(30 m) max

Peripheral Station (screw terminal)

one 22 AWG twisted pair

to last station: 100 ft.

(30 m) max

7953

Maximum Distance

Standard/Prism Zone Light Controllers Model

Function

Connects to

Cable Type

7971

Provide visual call signals within a certain zone area where patient room dome lights may not be visible

Gateway and/or Controller via 9779 Splitter (RJ45)

Factory furnished 6 inch cable

7972 7973

Š 2013 Jeron Electronic Systems Inc.

Maximum Distance

6-11

Cable Requirements & Distances

System Planning

Room Stations R Bus Stations Model 7912 7916 7917 7918 7919 7920 7922 7923 7924 7925 7926 7927

Function

Connect to

Provide full duplex hands-free communication and call-in points with the exception of VIsual Duty (7917) & Electrical Supervision stations (7918) that provide visual and tone call/alert annunciation only.

PA Page (7916) interfaces the

Nurse Consoles to external public address page systems

Cable Type

Maximum Distance

Cat-5/5e/6

to last station R bus station: 100 ft. (30 m) max

Audio stations in series to a Room Controller (RJ45) Note: Models 7916, 7918, and 7927 each require a dedicated Room Controller

P Bus Stations (Peripherals) Model 7930 7931 7932 7958 7934* 7937* 7940 7941 7945 7947 7949

Function

Connect to

Cable Type

Maximum Distance

Provide call-in points *exceptions

peripheral stations in series to a Room Controller (screw terminal)

one 22 AWG twisted pair

to last P bus station: 100 ft. (30 m) max

Nurse Consoles & Terminals (M Bus) Nurse Console & Terminals Model

7965 7967-P 7967-S

6-12

Function

Annunciates calls from staff/ patient stations and allows fullduplex (7965 only) two way voice communication between nurse and patient/staff For more information on Terminals, refer to page 5-1.

Connects to

Cable Type

Maximum Distance

Console Controller* (RJ45) may connect via 7969 Console Wall Jack for desk mounted nurse console

Cat-6

700 ft. (213 m) max.

Terminal connects to model 7960 *Controller must be equipped with dedicated power splitter to ensure adequate voltage from J Bus

Š 2013 Jeron Electronic Systems Inc.

Chapter 7: Device Installation

.

12/4/13

System Planning

Backboxes, Mounting Racks & Wall Cabinets Backboxes Jeron stations are mounted in UL Listed backboxes. Below are recommendations for specific backboxes. Use recommended Raco backboxes or UL Listed equivalent. .

Model #

Station

7917

Visual Duty

7918

Electrical Supervision

7930

Single Pushbutton

7931

Dual Pushbutton

7932/58

Pullcord/Pushbutton Bath

7934

Staff Presence

7937

Remote Cancel

7940

Procedure

7941

Dual Auxiliary Alarm Input

7945

Dual External Alarm Input

7947

8 Input Bed Interface

7949/7949P

Code Blue/Code Pink

7916

PA Page Interface

7950

Room Controller

7951

Room Controller with 2 LED Dome Lights

7952

Room Controller with 6 LED Dome Lights

7953

Room Controller with Prism Dome Lights

7960

Console Controller

7961

Console Controller with 2 LED Dome Lights

7962

Console Controller with 6 LED Dome Lights

7963

Console Controller with Prism Dome Lights

7971

Zone Light with 2 LEDs

7972

Zone Light with 6 LEDs

7973

Prism Zone Light

7912

Pushbutton Staff w/Audio

7919

Bath w/Audio

7927

Staff/Duty w/Audio

© 2013 Jeron Electronic Systems Inc.

Station Dimensions

Enclosure Type

Gang

Backbox & Trim Ring Options

Drywall: Raco 670 1-Gang Backbox 4" H, 2" W,2-1/8" D (10.1 H, 5 W, 5.4 D cm)

4.6" H,3" W,1" D (11.7 H, 7.6 W, 2.5D cm)

PC/ABS

1

Raco 232 2-Gang Backbox 4" H, 4" W, 2-1/8" D (10.1 H, 10.1 W, 5.4 D cm) with Raco 772 1-Gang Trim Ring 4" square cover, raised 1/2" (10.1 cm square cover, raised 1.2 cm) Masonry: Raco 690 1-Gang Masonry Box 2-1/2” deep

4.8” x 4.9” x 1.1” (12.1 x 12.4 x 2.7 cm)

4.8" H, 4.9" W, 3.7" D (12.1 H, 12.4 W, 9.3 D cm)

4.8” x 4.9” x 1.1” (12.1 x 12.4 x 2.7 cm) PC/ABS

4.8" H, 4.9" W, 3.7" D (12.1 H, 12.4 W, 9.3 D cm)

2

Drywall: Raco 232 4” Square Backbox 4" H, 4" W, 2-1/8" D (10.1 H, 10.1 W, 5.4 D cm) with Raco 778 2-Gang Trim Ring 4" square cover, raised 1/2" (10.1 square cover, raised 1.2 cm) Masonry: Raco 691 2-Gang Masonry Box 2-1/2” deep

4.8" H x 4.8" W x 1.2" D (12.2 H x 12.1 W x 3 D cm)

7-1

Backboxes, Mounting Racks & Wall Cabinets

Enclosure

Model #

Station

7920

Standard Single Callcord Patient

7922

Standard Dual Callcord Patient

7923

Enhanced Single Patient

7924

Enhanced Dual Patient

Masonry: Raco 692 3-Gang Masonry Box 2-1/2’ deep

7925

Single Patient

Drywall: Raco 232 4” Square Backbox 4" H, 4" W, 2-1/8" D (10.1 H, 10.1 W, 5.4 D cm) with Raco 778 2-Gang Trim Ring 4” square cover

7926

Dual Patient

Station Dimensions

System Planning

4.6" H, 6.8" W, 1.2" D (11.7, H, 17.2 W, 3 D cm)

4.6" H, 6.8" W, 1.2" D (11.7, H, 17.2 W, 3 D cm)

Type

PC/ABS

PC/ABS

Gang

3

3

Backbox & Trim Ring Options Drywall: Raco 942 3-Gang Backbox 4-1/2” H, 8-5/8” W, 2-1/2” D (11.4 H, 21.9 W, 6.3 D cm) with Raco 822 3-Gang Trim Ring 4-1/2” H, 8-7/8” W (11.4 H, 22.5 W cm)

Masonry: Raco 691 2-Gang Masonry Box 2-1/2” deep 7991/7991FX

Nurse Call Isolated 8 Port Ethernet Switch

7992/7993

Gateway

1.5 x 6.5 x 5.6 in.

(3.8 x 16.5 x 14.3 cm)

Rack mounted on standard 19” rack (model 9840 kit for up to three 7992/7993) or wall mounted on 7988/7989 Wall Mount Cabinet

7995

Power Supply and Backup Battery

4.0 x 19.0 x 3.6in.

(10 x 48 x 9 cm)

Rack or enclosure mounted

7965

Touchscreen Console

2.5 x 9 x 7.2 in.

(6.3 x 22.8 x 18.2 cm)

Rack mounted on standard 19” rack (model 9842 kit per one 7991) or wall mounted on 7988/7989 Wall Mount Cabinet

Desk Mounted on metal base or wall mounted on 9769 Wall Bracket: Raco 232 4” Square Backbox 4" H, 4" W, 2-1/8" D (10.1 H, 10.1 W, 5.4 D cm) with Raco 778 2-Gang Trim Ring 4" square cover, raised 3/4" (10.1 cm square cover, raised 1.9 cm)

8.3 x 9.2 x 3.0 in.

(21 x 23.3 x 7.6 cm) Footprint: 75.9 in² (489 cm²)

PC/ABS

8.3 x 6.8 x 1.8 inch

7967

Staff Duty/Workflow/Nurse Terminal

(21 x 17.2 x 4.6 cm) Footprint: 56.4 in² (364 cm²)

2

Masonry: Raco 691 2-Gang Masonry Box 2-1/2” deep Wall mounted on factory furnished 9 769 Wall Bracket Raco 232 4” Square Backbox 4" H, 4" W, 2-1/8" D (10.1 H, 10.1 W, 5.4 D cm) with Raco 778 2-Gang Trim Ring 4" square cover, raised 3/4" (10.1 cm square cover, raised 1.9 cm) Masonry: Raco 691 2-Gang Masonry Box 2-1/2” deep

7-2

© 2013 Jeron Electronic Systems Inc.

System Planning

Backboxes, Mounting Racks & Wall Cabinets

Jeron Mounting Kits & Wall Cabinets Model 9840 Rack Mount Kit Used with standard 19” Rack. Accommodates up to three Models 7992/7993 Gateway in 1.75 inches of rack space.

Figure 7.1: 9840 Rack with Gateway

Model 9842 Rack Mount Kit Used with standard 19” Rack. Accommodates up to one Model 7991 Isolated 8 Port Ethernet Switch.

In a rack, the equipment enclosures are screwed to mounting panels that fit into the mounting rack.

Figure 7.2: 9842 Rack with 7991 Isolated 8 Port Ethernet Switch

Product Model #

Rack Mount Kit Jeron #

# of Products Rack Accommodates

Rack Space Product Occupies

7992/7993

9840

3

1U (1.75 in.)

7991

9842

1

2U (3.50 in.)

7995

-

-

3U (5.25 in.)

Table 7.1: Jeron Rack Mount Kits

© 2013 Jeron Electronic Systems Inc.

7-3

Backboxes, Mounting Racks & Wall Cabinets

System Planning

Figure 7.3: Gateway and Switch Mounted on 19” Rack

Figure 7.4: 790 Rack Mounting Dimensions

7-4

© 2013 Jeron Electronic Systems Inc.

System Planning

Backboxes, Mounting Racks & Wall Cabinets

Model 7988/7989 Wall Mount Cabinet Wall Mount Cabinets are used to house the central equipment.

Figure 7.5: Wall Cabinet

Mounting

Keyholes on bottom

Construction

16 gauge steel with hinged cover and lock

Knockouts:

Four 1/2”, eight 3/4”, two 1-1/2”

Lock

Tumbler type with two keys provided

Subplate Studs:

Four #10-32

Size

7988: 24 × 18 × 4 in. (61 x 46 × 10 cm) 7989: 30 x 24 x 4 in. (76 x 61 x 10 cm)

Weight:

7988: 21 lb. (9.5 kg.)

7989: 35 lbs. (15.8 kg)

Associated Jeron Equipment

Jeron Model 7991/91-FX Isolated 8 Port Ethernet Switch Jeron Model 7992/93 Gateway Jeron Model 7995 Power Supply with Battery Backup

Table 7.2: 7988/7989 Technical Data

© 2013 Jeron Electronic Systems Inc.

7-5

Backboxes, Mounting Racks & Wall Cabinets

System Planning

18.000 3.063

11.875

.187 (4)

24.000

13.703

5.250

Figure 7.6: 7988 Dimensions

24.000

3.008

17.984

.187 (4)

30.000

20.000

5.031

Figure 7.7: 7989 Dimensions

7-6

Š 2013 Jeron Electronic Systems Inc.

System Planning

Backboxes, Mounting Racks & Wall Cabinets

Wall Cabinet Capacities

Contents

Cabinet Model 7988 (24x18 inch)

7989 (30x24 inch)

1 - 7995 Power Supply 1 - 7993/92 Gateway

Yes

Yes

1 - 7995 Power Supply 1 - 7993/92 Gateway 1 - 7991/91-FX Isolated 8 Port Ethernet Switch

Yes

Yes

1 - 7995 Power Supply 1 - 7991/91-FX Isolated 8 Port Ethernet Switch

Yes

Yes

2 - 7995 Power Supplies 2 - 7993/92 Gateways

No

Yes

2 - 7995 Power Supply 1 - 7993/92 Gateway

No

Yes

2 - 7995 Power Supplies 2 - 7993/92 Gateways 1 - 7991/91-FX Isolated 8 Port Ethernet Switch

No

Yes

2 - 7995 Power Supplies 1 - 7993/92 Gateway 1 - 7991/91-FX Isolated 8 Port Ethernet Switch

No

Yes

Table 7.3: Wall Cabinet Capacities

Maximum Fastener Height The combined height of fastener and washer (if used) must not exceed 3/16� from the enclosure base when mounting the enclosure.

Cabinet subplates are prepared with threaded fasteners to accept respective equipment units.

When placing the equipment units in the cabinets, it is crucial to observe orientation. Panels with connectors must have enough clearance to allow connection to the relevant equipment. Refer to orientation below.

Š 2013 Jeron Electronic Systems Inc.

7-7

Backboxes, Mounting Racks & Wall Cabinets

System Planning

Model 7995 Power Supply

Model 7991/91-FX Isolated 8 Port Ethernet Switch

Model 7993 Gateway

Figure 7.8: Model 7988 Equipment Assembly Orientation

Model 7993 Gateway Model 7995 Power Supply Model 7991/91-FX Isolated 8 Port Ethernet Switch

Model 7993 Gateway

Model 7995 Power Supply

Figure 7.9: Model 7989 Equipment Assembly Orientation

7-8

Š 2013 Jeron Electronic Systems Inc.

System Planning

Backboxes, Mounting Racks & Wall Cabinets

Jeron Wall Mounting Bracket for Consoles & Terminals Nurse consoles and terminals can be wall mounted using model 9769 Wall Mounting Bracket with the relevant backbox.

4.500 1.813 .907

4.500

3.281

.150 Countersink

Figure 7.10: Wall Mounting Bracket Dimensions

Š 2013 Jeron Electronic Systems Inc.

7-9

Backboxes, Mounting Racks & Wall Cabinets

7-10

System Planning

Š 2013 Jeron Electronic Systems Inc.

Chapter 8: Networking, Programming and Integrations

. .

System Planning

Network Overview

Network Overview After installation of facility patient and staff devices, the Jeron headend devices are connected, then networked to the facility LAN via a Bridge PC to enable the programming of the 790 system and addition of optional system integrations.

Provider 790 headend devices consist of the Gateways (Model 7993/2), Isolated 8 Port Ethernet Switches (Model 7991 or Model 7991-FX with Fiber Uplink option), and necessary Power Supplies (Model 7995). The components are designed for rack mounting on a standard 19" rack or wall mounting on a Jeron wall cabinet.

Each Model 7993/2 Gateway connects to the Jeron Power Supply with Battery Backup (Model 7995). A supplemental power wire or an additional Model 7995 Power Supply may be required.

Each Isolated 8 Port Ethernet Switch can accept connections of up to eight Gateways. For more than eight Gateways in a system, multiple switches will be used. Multiple switches in a system interconnect via their Uplink Port (port 9). The main Isolated Switch also connects to the facility LAN via a Bridge PC running a model 7984 Bridge application.

Isolated 8 Port Ethernet Switch (with Fiber Uplink Option) Model 7991 Model 7991-FX The Isolated 8 Port Ethernet Switch and Switch with Fiber Uplink are used to interconnect local Nurse Call Gateways and integrate them into the entire distributed Nurse Call Network. Utilizing industry standard network wiring, cabling, and connectors, multiple interconnected Ethernet Switches can support a nurse call network of up to 127 Nurse Call Gateways operating as a single distributed system. Should the nurse call network connection be broken at any point, the downstream Ethernet Switches and Nurse Call Gateways will continue to operate as a sub-system.

Up to eight Gateways can connect to one Isolated 8 Port Ethernet Switch.

Distance between Gateway and 7991 switch should not exceed 328 ft.(100 m). Up to 16 Switches for Gateway connections, plus an additional three Switches for Switch-to-Switch connections, are permitted on a single 790 system. There may be no more than eight (8) Switches between any two Gateways.

To support remote and distributed Nurse Call Gateways as part of a single Nurse Call Network, the model 7991-FX Switch includes a fiber uplink port with a duplex SC connector to support distances of up to 2 km to another 7991-FX switch over dedicated 62.5/125 Âľm multi-mode fiber. The standard 7991 and fiber enabled 7991-FX switches can be intermixed as part of the same system.

For programming and integration purposes, a top-level switch, wired to the Bridge PC interconnects the Jeron IP Network and the Hospital LAN.

Š 2013 Jeron Electronic Systems Inc.

8-1

Isolated 8 Port Ethernet Switch (with Fiber Uplink Option)

System Planning

The unit is housed in a sturdy aluminum enclosure and may be mounted in a standard 19” width data rails or equipment rack (using a Jeron Model 9842 adaptor) or a wall cabinet.

Figure 8.1: Isolated 8 Port Ethernet Switch Model 7991

Figure 8.2: Fiber Uplink Option on Model 7991-FX

Dimensions

2.5 x 9 x 7.2 in. ( 6.3 x 22.8 x 18.2 cm)

Mounting

19 inch rack (using model 9842 adaptor) or Jeron wall cabinet

Electrical Rating

Model 7991: 40 V @ 3.9 W Model 7991-FX: 40 V @ 5.8 W

Indicators

9 – Activity 1 – Uplink 1 – 10/100

Terminations

8 – RJ-45 10/100 Ethernet Ports 1 – RJ-45 10/100 Uplink Port (Model 7991) 1 – Duplex SC Fiber Uplink Port (Model 7991-FX) 1 – Power, 2 conductor plug in connector

Table 8.1: 7991 Technical Data

8-2

© 2013 Jeron Electronic Systems Inc.

System Planning

Isolated 8 Port Ethernet Switch (with Fiber Uplink Option)

Associated Equipment for Isolated 8 Port Ethernet Switch Equipment

Purpose

Power Supply and Battery Backup (Model 7995)

Powers all nurse call devices including Isolated Switches, Gateways, Nurse Consoles, Workflow/Staff Duty/Nurse Terminals, dome lights, patient stations, and staff stations.

19” Rack (using model 9842 adaptor) or Wall Mount Cabinet 7988/7989

Houses Isolated 8 Port Ethernet Switch

Cat-5/6 Cable

Wires the Isolated 8 Port Ethernet Switch

Table 8.2: Equipment for Isolated 8 Port Ethernet Switch

Gateway connection to Switch in Five-floor Facility Cat-5 Gateway

Cat-5 Gateway

Cat-5

Cat-5

Power Supply

Power Supply

Gateway

Power Supply

Gateway

Power Supply

Floor 5

Floor 4

Floor 3

Floor 2

Cat-5 Nurse Call Isolated 8 Port Ethernet Switch Uplink Port

Gateway

Bridge PC w/7984 Bridge Application

Power Supply

Installer PC (provided by others) w/7990

Floor 1

Maximum distance of 328 ft. (100 m) from Gateway to 7991 Switch

Figure 8.3: Gateway Connections to an Isolated 8 Port Ethernet Switch in a Five-Floor Facility

© 2013 Jeron Electronic Systems Inc.

8-3

Isolated 8 Port Ethernet Switch (with Fiber Uplink Option)

System Planning

Interconnected Switches and Connected Gateways To Bridge PC 6 Isolated Switches 40 Gateways 1240 Rooms

6

1240 Rooms

Isolated 8 Port Ethernet Switch

5

40

Gateways 992 Rooms

Isolated 8 Port Ethernet Switch

Isolated 8 Port Ethernet Switch

4

Gateways 744 Rooms

Isolated 8 Port Ethernet Switch

3

Gateways 496 Rooms

Gateway

248 Rooms

Isolated 8 Port Ethernet Switch

2

016 Isolated 8 Port Ethernet Switch

009

1 Gateway

001

008

Figure 8.4: Isolated Switches and their Connected Gateways

8-4

© 2013 Jeron Electronic Systems Inc.

System Planning

Bridge PC and the Jeron IP Network

Bridge PC and the Jeron IP Network The connection of the Jeron network to the facility LAN via a Bridge PC enables the programming of the 790 system and optional system integrations.

The Model 7984 Bridge PC Application is the central point which communicates with all installed Jeron series 79xx applications. The PC on which this application is running must be equipped at all times with a Jeron factory furnished hardware protection key in order for any 790 software application to function with the 790 system hardware.

Model 7984 Bridge PC also provides capability for off-site upgrades and diagnostics of hardware and software. Using Model 7990 Administration software for programming on the Bridge PC along with a remote access utility allows a remote connection to be made through the Internet.

Figure 8.5: Provider 790 Computer Integrations

Bridge PC Setup For integration options and to program the Provider 790 Nurse Call System you will need a PC (provided by others) with the 7984 LAN Bridge application.

Minimum requirements for PC(s) hosting Jeron Provider 790 applications vary depending on the number of beds installed. For systems larger than 150 beds

Š 2013 Jeron Electronic Systems Inc.

8-5

Bridge PC and the Jeron IP Network

System Planning

with optional system integrations, additional PC(s) are required and an alternate connection using a commercial Ethernet switch (provided by others) between the main Isolated Switch and the PCs is necessary.

Number of Beds

Number of Required PCs

Up to 150

1

151-500

2

501-1500

2

Over 1500

consult factory

Table 8.3: Provider 790 Capacity & Number of PCs

Minimum PC Requirements For systems 150 beds or less: • • • • • • • • •

Number of PCs required: 1 Operating system: Windows 7 or 8 Pro 64 bit or Windows Server 2008 R2 Database software (required for integrations with a database component): Microsoft SQL Server 2008 R2 Express or Standard Edition* Processor: Intel or AMD quad core 64 bit processor RAM: 8 GB minimum Hard Drive: 500 GB minimum Network Interface: (2) 10/100 LAN ports Serial Interface: (1) motherboard, PCI or PCIe RS-232 serial port USB interface: (2) available USB 2.0 ports

*Microsoft SQL Server Express or Standard Edition is required for integrations with a database component (7970, 7980, or 7983). The end-user organization must determine appropriate SQL Server licensing. SQL Server Express can be used for 7980 software on Provider 790 systems up to a maximum of 150 beds. Standard edition is required for 7983 software. Consult individual software installation manuals for additional guidelines.

Minimum PC Requirements ( 151+ Beds) A minimum of two PCs is necessary when the number of beds exceeds 150.

The addition of a PC, with two NIC cards, requires the use of a commercial Ethernet switch (provided by others) for proper configuration with the Nurse Call System. Refer to Figure 8.6 for dual server configuration.

8-6

© 2013 Jeron Electronic Systems Inc.

System Planning

Bridge PC and the Jeron IP Network

Figure 8.6: Dual Server Configuration

For 151 to 500 beds: •

Number of PCs required: 2 (One to host Jeron apps; one to host the SQL Database.)

Application Server • Operating system: Windows 7 or 8 Pro 64 bit or Windows Server 2008 R2 • Processor: Intel or AMD quad core 64 bit processor • RAM: 8 GB minimum • Hard Drive: 500 GB minimum • Network Interface: (2) 10/100 LAN ports • Serial Interface: (1) motherboard, PCI or PCIe RS-232 serial port • USB interface: (2) available USB 2.0 ports Database Server • Operating system: Windows 7 or 8 Pro 64 bit or Windows Server 2008 R2 • Database software (required for integrations with a database component): Microsoft SQL Server 2008 R2 Express or Standard Edition* • Processor: Intel or AMD quad core 64 bit processor • RAM: 8 GB minimum • Hard Drive: 500 GB minimum • Network Interface: (1) 10/100 LAN port • Serial Interface: none required • USB interface: (2) available USB 2.0 ports *Microsoft SQL Server Express or Standard Edition is required for integrations with a database component (7970, 7980, or 7983). The end-user organization must determine appropriate SQL Server licensing. SQL Server Standard Edition is required for 7980 software on Provider 790 systems in excess of 150 beds. Standard edition is required for 7983 software. Consult individual software installation manuals for additional guidelines.

© 2013 Jeron Electronic Systems Inc.

8-7

Bridge PC and the Jeron IP Network

System Planning

For 501 to 1500 beds: •

Number of PCs required: 2 (One to host Jeron apps; one to host the SQL database)

Application Server • Operating system: Windows Server 2008 R2 • Processor: Intel or AMD quad core 64 bit processor • RAM: 8 GB minimum • Hard Drive: 1 TB Mirrored RAID minimum • Network Interface: (2) 10/100/1000 LAN ports • Serial Interface: (1) motherboard, PCI or PCIe RS-232 serial port • USB interface: (2) available USB 2.0 ports Database Server • Operating system: Windows Server 2008 R2 • Database software (required for integrations with a database component): Microsoft SQL Server 2008 R2 Express or Standard Edition* • Processor: Intel or AMD quad core 64 bit processor • RAM: 8 GB minimum • Hard Drive: 1 TB Mirrored RAID minimum • Network Interface: (1) 10/100/1000 LAN port • Serial Interface: none required • USB interface: (2) available USB 2.0 ports *Microsoft SQL Server Express or Standard Edition is required for integrations with a database component (7970, 7980, or 7983). The end-user organization must determine appropriate SQL Server licensing. SQL Server Standard Edition is required for 7980 software on Provider 790 systems in excess of 150 beds. Standard edition is required for 7983 software. Consult individual software installation manuals for additional guidelines.

For 1500+ beds: For systems consisting of more than 1500 beds, consult factory for minimum requirements.

8-8

© 2013 Jeron Electronic Systems Inc.

System Planning

Required Software Applications

Required Software Applications Model 7984 Bridge Software Application The Jeron Model 7984 Bridge Software Application is used with the Provider 790 Nurse Call System to connect the nurse call to the facility's LAN and in turn other optional Provider 790 software applications residing on the LAN. The 7984 Bridge is linked to the Provider 790 Nurse Call System through the isolated port on the UL1069 Listed Model 7991 Ethernet Switch.

The PC running the 7984 Bridge Software must be equipped with two NICs (Network Interface Cards). The Bridge software acts as a data firewall isolating each operating Gateway (the Jeron IP Network) connected to Network Interface Card #1 on the Bridge PC and any other device such as client PCs on the Hospital LAN connected to Network Interface #2. It blocks all other LAN activity from the nurse call system.

Using TCP/IP, the 7984 software provides a secure data connection to the Provider 790 software applications on the LAN. The 7984 software also reads the LAN NTP (Network Time Protocol) and relays this time to the Provider 790 Nurse Call System so that both the nurse call and facility LAN share the same time base. Through 7984, technicians on any PC on the facility's LAN running the Provider 790 7990 Administration Software have remote access to the entire nurse call system for programming, firmware updates, and troubleshooting.

Model 7990 Administration Software The Jeron Model 7990 Administration and Programming Software is used to program and administer the Provider 790 Nurse Call System through the 7984 Bridge Software and associated Bridge PC. The 7990 software allows a technician to program and manage all system attributes including room numbers, call priorities, call tones, dome light indications, swing rooms, and coverage of duty stations, zone lights, Workflow/Staff Duty/Nurse Terminals, and Nurse Consoles. With 7990, the Provider 790 system may be configured, downloaded (for archiving), restored, and edited without affecting the local operation of the nurse call system.

The 7990 software also supports firmware updates for all nurse call hardware devices including Gateways, Controllers, Nurse Consoles, and Terminals.

Gateways must be programmed with a unique IP address and location name prior to wiring on the J Bus. Refer to Installation & Programming Manual for instruction.

Programming System Configuration Below is an overview of the programming process with 7990 Administration Software. Refer to the Provider 790 Installation & Programming Manual for details: •

Stations, terminals and consoles are wired to a Controller and share the Controllers’ room name (ID). The Controller comes with a default ID that can be changed in programming to reflect the location of the devices/room. After Controllers have been identified and assigned a location-specific name, a visual diagram of the facility is created. The

© 2013 Jeron Electronic Systems Inc.

8-9

Required Software Applications

System Planning

diagram consists of buildings, floors, units and coverage areas. There should be a minimum one coverage area per unit.

Note: All rooms report to all Nurse Consoles by default.

The assignment to coverage areas is done in programming.

8-10

•

Floors and Units: A Gateway would be utilized on a single floor, and may cover all or some of the rooms on a certain floor. A unit may require more than one Gateway if the unit exceeds the number of supported rooms (max 31). In that case, multiple Gateways will be used on the floor. One Gateway may be sufficient for multiple units on a floor if the units are small and do not exceed the 31 room limit or the 700 foot J Bus limit.

•

Coverage Areas: Coverage area(s) include rooms within a unit that are covered by a specific Nurse Console. A unit may contain one coverage area (i.e., all rooms assigned to a Nurse Console) or multiple coverage areas (where rooms are assigned to multiple Nurse Consoles). Typically, rooms in a unit are physically located in the same part of the facility, (i.e., the same floor or wing). Each room is assigned to a coverage area by adding stations and Consoles/ Terminals to the facility diagram in 7990. This determines the rooms/ areas that report to and annunciate calls to a particular Nurse Console. Refer to Figure 8.7.

•

Duty Areas: Room stations, Model 7917 Visual Duty, and Model 7927 Staff/Duty are assigned to duty areas. Model 7967-S Staff Duty Terminals are programmed to show active calls within its assigned coverage area, with calls grouped by Routine, Urgent, Emergency, and Code. Duty stations respond simultaneously and identically to calls from room stations programmed to report to the duty area.

•

Zone Areas: Room stations and Zone Lights are assigned to zone areas. Zone Lights respond simultaneously and identically to calls from room stations programmed to report to the zone area.

© 2013 Jeron Electronic Systems Inc.

System Planning

Required Software Applications

.

COVERAGE AREA PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

UNIT

COVERAGE AREA PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

COVERAGE AREA PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

UNIT

COVERAGE AREA

PATIENT ROOM

PATIENT ROOM

PATIENT ROOM

PATIENT ROOM PATIENT ROOM

Figure 8.7: Units, Rooms and Coverage Areas

© 2013 Jeron Electronic Systems Inc.

8-11

Optional Software Integrations

System Planning

Optional Software Integrations The Model 7984 Bridge PC Application communicates with all installed Jeron series 79xx optional integrations. For any optional integration to function with the 790 system hardware, the installation PC must be equipped at all times with a Jeron factory furnished hardware protection key.

The optional integrations available in Provider 790 are as follows: • • • • • • • • •

Model 7970 Automatic Voice Prompt Software Model 7977 ADT Patient Information Application Model 7978SIP SIP Phone Integration Software Model 7980 Staff Assignment & Messaging Software Model 7981 RTLS Integration Software Model 7983 EIS Activity Logging & Reporting Software Model 7985 PC Console Software Model 7986 Map Configuration Software Model 6894 Integration Data Service

The installation and use of these applications are covered in the Provider 790 Advanced Training class.

Bridge PC System Requirements Use of optional integrations requires presence of the following system components on the Bridge PC: •

Microsoft .NET 4.0 Framework, both Client and Extended versions.

Refer to integration installation manual for further instruction

•

Windows IIS Web Server 7.5

•

Microsoft SQL Server 2008 R2 Express or Standard Edition*

•

Use Internet Explorer 8 or greater to run browser-based interface for applications

*Microsoft SQL Server Express or Standard Edition is required for integrations with a database component (7970, 7980, or 7983). The end-user organization must determine appropriate SQL Server licensing. SQL Server Express can be used for 7980 software on Provider 790 systems up to a maximum of 150 beds. Standard edition is required for 7983 software.

For minimum requirements of the installation PC(s) hosting Provider 790 integrations, refer to page 8-6. Integrations that incorporate access to client software components on a networked facility PC must adhere to additional minimum requirements.

Minimum Client PC Requirements The following minimum hardware, software, and operating system requirements apply to the networked facility PC(s) used to access the client software component of Model 7980 Staff Assignment & Messaging Software, the browser-based interface of Model 7983 EIS Activity Logging & Reporting Software, or the client software component of Model 7985 PC Console:

8-12

•

1 GHz or faster 32-bit (x86) or 64-bit (x64) processor

•

Windows XP Pro or Windows 7 Pro, 32 or 64 bit

•

1 GB RAM (32-bit) or 2 GB RAM (64-bit)

•

One (1) 10/100 LAN Port

© 2013 Jeron Electronic Systems Inc.

System Planning

Optional Software Integrations

•

.NET 4.0 Framework, both Client and Extended versions. Refer to integration installation manual for further instruction

•

Use Internet Explorer 8 or greater to run browser-based interface for applications

The following is a brief overview of the available Provider 790 integrations for added functionality and support of popular third-party equipment and applications:

Model 7970 Automatic Voice Prompt Software Provides verbal annunciation of select Provider 790 Nurse Call System call events over a facility's overhead paging system. Pages are triggered by nurse calls placed or cancelled from patient rooms or staff stations. Voice prompts consist of phrases that include instructional content as well as call type and room location information. Voice prompts can be customized on-site to meet facility requirements for privacy and content. For example: A code call in room 206 annunciates "Stat condition in second floor physical therapy." Upon cancellation: "Medical condition in physical therapy has been cancelled."

7970 requires Model 9815-1 single channel USB Zone Control, or 9815-2 eight channel USB Zone Control with optional 9815-3 USB Mute Contact.

This integration requires Microsoft SQL Server. Refer to ‘Minimum PC Requirements” on page 8-6 for more information.

Model 7977 ADT Patient Information Integration Software The Jeron Model 7977 ADT Patient Information Integration Software is used with the Provider 790 Nurse Call System to integrate with the facility's ADT system for automated update of patient information displayed at nurse consoles/terminals, PC consoles, and staff duty terminals.

When patient information and assigned bed information are updated on the ADT system, the 7977 listens for updates over the HL7 protocol standard and automatically sends this information to the Provider 790 Nurse Call System to display the information when a patient places a call. The patient information is displayed at Jeron model 7965 Nurse Console, 7967 Staff Duty/Nurse Terminal and 7985 PC Console Application.

When the integration software is configured, the installer can determine which ADT information fields are mapped to the nurse call system including: patient name, doctor, and up to several fields of patient information. Alternately, during configuration, key ADT information fields may be blocked from being displayed on the nurse call system. To ensure compliance with HIPAA patient confidentiality requirements, the patient information is stored securely within the nurse call system and is only displayed at Nurse Consoles, PC Consoles, and Staff Duty or Nurse Terminals within staff areas.

Model 7978SIP SIP Phone Integration Software The Jeron Model 7978SIP SIP Phone Integration Software is used with the Provider 790 Nurse Call System to route patient calls on the nurse call LAN. Through the intermediary Brekeke SIP Server, the SIP phone call is routed to the facility’s SIP Telephony Call Server and in turn over the facility’s Voice over Wireless LAN to the SIP end device carried by the assigned caregiver.

© 2013 Jeron Electronic Systems Inc.

8-13

Optional Software Integrations

System Planning

The 7978SIP routes calls based on the patient-to-staff and staff-to-device assignments programmed into the Jeron Model 7980 Assignment Software.

From their SIP wireless phones, caregivers can also call into any staff intercom or patient intercom station on the Provider 790 nurse call system.

Each J Bus with patient intercom stations has eight simultaneous full duplex audio circuits which provides non-blocking service for multiple SIP phones calling to the same J Bus.

Model 7980 Staff Assignment & Messaging Software The Jeron Model 7980 Staff Assignment and Messaging Software is used to manage mobile locating and notification devices for the Provider 790 Nurse Call System. Through this software, system administrators, technicians, and charge nurses manage all wireless devices, staff member attributes, staff to device assignments, staff to patient assignments, and staff to team assignments. The software itself sends messages over TAP protocol directly to paging encoders or wireless phone middleware. In addition to the 7980 software, integration for wireless phone communication and real time locating tags requires integration software and/or hardware from Jeron.

For the end-user, access to the software is .NET browser-based allowing users to sign on from any PC on the LAN. Based on their account security, users can do the following: •

Configure system wide settings including name format, call response timers, pager cancellation messages

•

Add/edit mobile locating and notification devices including wireless phones, pocket pagers, and real time locating tags

•

Manage signon access levels and access to functions and nursing units

•

Create and assign staff to facility-wide crash teams, such as code crash teams, and local emergency all call teams

•

Manage the association of staff and devices to one, several, or all units within the facility

•

For each of up to three shifts per unit per day, assign from one to three team members to each patient room/bed for notification plus a unit level backup

•

Configure notification to technician(s) phone/pager for instant alerting of any component failures

This integration requires Microsoft SQL Server. Refer to ‘Minimum PC Requirements” on page 8-6 for more information.

Model 7981 RTLS Integration Software The Jeron Model 7981 RTLS (Real Time Locating System) Integration Software is used with the Provider 790 Nurse Call System to integrate with the facility's RTLS server for automated staff locating. The 7981 provides a single point of connection between the RTLS server and the Provider 790 system and supports the most popular locating systems on the market.

The RTLS automated staff location integration provides the following functionality on the nurse call system:

8-14

© 2013 Jeron Electronic Systems Inc.

System Planning

Optional Software Integrations

•

Automatic registration of staff in and out of patient rooms

•

Dome light indication of staff present in each room (green, orange, or yellow)

•

Automatic cancellation of outstanding service requirements by staff with locating tags walking into the patient room

•

Locate staff by level and name from any Nurse Console/Terminal or Staff Duty Terminal with one-touch to communicate with staff via the closest intercom station

The 7981 is used in conjunction with the Jeron Model 7980 Staff Assignment Software which associates the locating tag with a specific staff member and their registration level (green, orange, or yellow). If the staff tag is equipped with a call button, when the button is pressed while in a patient room it will place a predetermined call priority level from that room.

Model 7983 EIS Log Report The Jeron Model 7983 Executive Information System (EIS) Software Package is used with the Provider 790 Nurse Call System for archiving and analysis reports of patient call and staff response activity. All nurse call activity data, including patient and staff calls, staff registration, voice response time, staff response time, and system supervision messages are logged in a SQL database.

From any PC on the facility's LAN, through the browser interface, staff can sign in and generate standard and customized reports for a single unit, a combination of units, or the entire facility. The staff member's signon privileges determine which unit(s) and types of reports they can generate.

Reports are produced in a standard PDF format allowing for easy printing.

Email feature allows for the scheduling and automatic delivery of future reports.

This integration requires Microsoft SQL Server. Refer to ‘Minimum PC Requirements” on page 8-6 for more information.

Model 7985 PC Console Software Model 7986 Map Configuration Software

Note: When operating in Associated Mode, each Model 7965 Nurse Console can only be associated with a single Model 7985 PC Console client PC.

Accessible via any PC on the facility's LAN, the Jeron Model 7985 PC Console Software is used with the Provider 790 Nurse Call System for a realtime view of nurse call activity and to initiate/review staff roundings. The client software component of the 7985 application resides on non-dedicated Windows® computers and communicates via TCP/IP to the server component to ensure only authorized staff have access to nurse call activity. Multiple users can simultaneously run local 7985 software on their own PCs; each with their own view of nurse call activity. The architecture of the 7985 software and the Provider 790 Nurse Call System precludes any activity on the LAN from adversely affecting the life safety operation of the Provider 790 Nurse Call System.

The software supports three views: List, Whiteboard, and Map. List view displays active events including patient and staff calls, overtime service requests, expired roundings and self-reminders, and active work flow events. The nurse call activity displayed in list view can be independent or

© 2013 Jeron Electronic Systems Inc.

8-15

Optional Software Integrations

System Planning

associated with the operation of a specific Model 7965 Nurse Console. In the independent display mode, the software can be customized by coverage area (one unit, several units, or the entire facility), by call priorities to display (one, several, or all), to display service requirements or not, to display work flow events (one, several, or all), to display staff locations or not, and to display staff roundings or not. When associated with a nurse console, the software will show all call activity based on the console's coverage.

Whiteboard view lists all rooms/beds and associated information (patient information and assigned staff), active call events, staff presence, roundings, self-reminders, Stryker® iBed Awareness status, and/or workflow events for the selected nursing unit. The display of patient information also requires the addition of the Jeron 7977 ADT Patient Information Integration Software.

Note: 7985 map view requires optional model 7986 Map Configuration Software.

Map view displays events and activity associated with each room (including active calls) on a graphical floor layout for the selected nursing unit. For each unit, the map view supports the display of up to 192 rooms on up to four views total. The map view automatically switches to the map with the highest priority active call. Map view requires optional 7986 Map Configuration Software.

The 7985 also allows nurse managers from any networked PC to set and review existing roundings or one time reminders on a per patient bed basis.

From any networked PC, when used in conjunction with the required Jeron 7980 Staff Assignment & Messaging Software, the 7985 also allows administrators and staff to send text message to the wireless phone or pager carried by specific staff members or to send group messages to caregiver's phones and/or pagers.

Model 6894 Integration Data Service Achieves platform inter-operability between Provider 680 and Provider 790 systems for improved communication and analysis of nurse call activity in a single facility. An integrated communication system gives staff and caregivers greater flexibility to observe, respond to, and analyze all system activity from any PC on the facility LAN. The Integration Data Service transmits configuration and call information from Provider 680 systems directly to the 7984 Bridge PC application. Information is disseminated directly from the Bridge application to the following system integrations: •

Model 7970 Automatic Voice Prompt Software for verbal annunciation of nurse call events on facility’s overhead paging system

•

Model 7980 Staff Assignment & Messaging Software for appropriate call routing to caregiver device

•

Model 7983 Executive Information System (EIS) Software for archiving and analysis reports of call activity

•

Model 7985 PC Console for a real-time view of nurse call activity

The 6894 service tool centralizes nurse call operation by combining attributes of both Provider platforms. System configurations are integrated by associating 680 controllers and coverage areas to new units in the 790 system (if present), and associating 680 call types with 790 equivalents. The tool then produces a single architectural diagram configuration file used to transmit global configuration via Model 7990 Administration Software. All

8-16

© 2013 Jeron Electronic Systems Inc.

System Planning

Optional Software Integrations

connections and data transmissions are performed without affecting the local operation of the nurse call systems.

Š 2013 Jeron Electronic Systems Inc.

8-17

Optional Software Integrations

8-18

System Planning

© 2013 Jeron Electronic Systems Inc.