4 minute read
X12 TL GW & X14 TL GW
TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.
BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES
Advertisement
ISO 5355
ISO 23223 WTR ISO 9523
WARNING
THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Ski boots equipped with « GripWalk » labelled kit of walking soles Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.
SOLE LENGTH ADJUSTMENT 260mm – 360mm
ALPINE SKI BOOTS (ISO 5355) TYPE A (Adult) TYPE C (Children)
GRIPWALK BOOTS (ISO 23223) TYPE A (Adult) TYPE C (Children)
WARNING
TO BE COMPATIBLE WITH GRIPWALK BOOTS, THE CENTRAL LEVER OF THE PLATE MUST BE MARKED WITH THE GRIPWALK LOGO.
WITHOUT THIS LOGO ON THE LEVER, COMPATIBILITY IS NOT POSSIBLE.
GRIPWALK COMPATIBILITY EXCLUSION
OLD GRIPWALK DESIGN - VERSION 1 CURRENT GRIPWALK DESIGN - VERSION 2
NO GAP BETWEEN FRICTION AREA AND CRAMPON
NO COMPATIBILITY of K2 BFC boot with GripWalk outsole Version 1 OK COMPATIBILITY of K2 BFC boot with Gripwalk outsole version 2
M O D E L - S P E C I F I C I N ST R U CT I O N S > > > X12 TL GW & X14 TL GW
MOUNTING & ADJUSTING
1. Open the central lever.
2. Insert the toe piece and position on the track according to the boot sole length.
3. Insert the heel piece and position it on the track according to the boot sole. 4. When the binding is adjusted to the sole length, locked the central lever, and check that the lever is completely closed.
5. Select and adjust the setting release values for toe and heel pieces. Step-in the boot, check and adjust the forward pressure.
#3
MNC (MULTI-NORM CERTIFIED) BINDINGS ARE INTENDED TO BE USED WITH FOLLOWING SKI BOOTS:
ISO 5355
ISO 23223 WTR ISO 9523
WARDEN MNC 11 DEMO BINDING . . . . . . . . . . . 86 WARDEN MNC 11 BINDING . . . . . . . . . . . . . . . 88 WARDEN MNC 13 DEMO BINDING . . . . . . . . . . . 90 WARDEN MNC 13 BINDING . . . . . . . . . . . . . . 92 N STH2 16 MNC BINDINGS . . . . . . . . . . . . . . . 94 GUARDIAN MNC BINDING - BACKCOUNTRY . . . . . . 97 S LAB SHIFT MNC 10 & 13 BINDING . . . . . . . . . . 101 N STRIVE 16 MN BINDING . . . . . . . . . . . . . . . 104
WARNING
THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Touring boots compliant with ISO 9523 standard > Ski boots equipped with “WTR technology” pads or with “GRIPWALK” pads
Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.
