Page 1

PB-S80 OEM Kjellberg速

System FineFocus 800 Plus


1 2 3 4 5

6 7


Centricut part number

Reference number


C117-155 C117-157 C53-261 C117-271 C117-164 C117-420* C117-425 C117-427 C117-153 C117-1300*

11.833.101.155 11.833.101.157 11.833.101.261 11.836.901.271 11.836.901.164 11.836.921.420 11.836.921.425 11.836.921.427 11.836.921.153 11.836.921.300

Swirl Gas Cap, 3.5mm, V4335 Swirl Gas Cap, 4.5mm, V4345 Protective Cap, V501 Swirl Gas Nozzle, T521 Nozzle Cap, T3045 CoolFlow Nozzle, 2.0mm, O2, 200A, T2120 CoolFlow Nozzle, 2.5mm, O2, 250A, T2125 CoolFlow Nozzle, 2.7mm O2, 300A, T2127 Gas Guide, T101 SilverLine Electrode, O2/Air, T012

Pkg qty 1 1 1 1 1 1 1 1 1 1







Centricut and SliverLine are registered trademarks of Hypertherm, Inc. and may be registered in the United States and/or other countries. All other trademarks are the properties of their respective owners. Centricut is in no way affiliated with Kjellberg.



Powermax Selection Guide Centricut consumables for Kjellberg FineFocus 800 Plus and HiFocus 280i/360i/440i ®




Technology Upgra de Cen tricut VS OE M

Upgrade to Centricut consumables to lower operating costs without sacrificing cut quality and productivity.

SilverLine electrode Solid silver front end enhances performance

Yellow XLife electrode

Copper back end reduces cost

All silver electrode increases cost

CoolFlow nozzle Deep cooling groove maximizes life

Yellow XLife nozzle Shallower cooling groove

Hypertherm patented technology • S  ilverLine® and CoolFlow® technologies deliver exceptional cut quality, long life, and fast cutting speeds. • S  ilverLine and CoolFlow consumables set the standard by which other manufacturers measure themselves. • R  un SilverLine electrodes and CoolFlow nozzles for their full life without risking damage to other consumables.

Lower overall cost • Competitively priced compared to the OEM. • L  ocal stocking on a global basis – product is delivered quickly reducing your inventory carrying costs.

Hypertherm quality and consistency • Precision manufacturing assures reliability of your cutting process. • D  esigned with critical-to-function tolerances to deliver the best quality product every time. • Easy to use – no special system set-up required.

SilverLine electrodes and CoolFlow nozzles are engineered and manufactured to Hypertherm standards, with industry-leading quality and consistency.

Angled o-ring seal remains cooler

Thicker walls dissipate heat and extend life

Compa tible with

Kjellberg torches • PerCut 370.2 • PB-S80W

Hotter o-ring

Thinner walls

Centricut products deliver long consumable life and exceptional cut quality at a competitive price. OPERATOR INFOR MA TION

Achieve maximum consumable life A fully used SilverLine electrode will have a pit depth of 2.5 mm (.100"). Properly tighten the nozzle cap: Make sure the nozzle cap is sealed tightly against the nozzle to maintain a proper seal and prevent leaking. Purge torch: After each parts change purge the torch for at least 30 seconds to remove residual moisture.


Leak check: After purging the torch make sure all o-ring and metal-to-metal seals are working as designed. Adjust gas flows: Plasma gas flow rate is critical. High flow will cause rapid electrode wear and hard starting. Low flow will cause uncontrolled arcing. (See cutting tables in your owner’s manual.)

2. 3.

Pierce at correct height: Piercing too low causes molten metal (spatter) to hit the swirl gas cap and nozzle. This is the most common cause of premature nozzle failure. Piercing too high can cause slow arc transfer and misfires. Adjust arc voltage: As the electrode wears, the torch will get closer to the plate. To maintain optimum cutting height, increase arc voltage in 2-volt increments, up to 10 volts higher than the initial setting. Avoid arc stretching: This can occur during rip cutting off the plate or when the lead out is improperly programmed. This shortens consumable life. Clean the nozzle and swirl gas cap: Periodically clean the nozzle and swirl gas cap to remove spatter. This will prevent double arcing which shortens consumable life.

4. Parts list

1. 2. 3.








7. 9.

Contact Hypertherm to locate a distributor near you. Hypertherm, Centricut, SilverLine and CoolFlow are trademarks of Hypertherm, Inc., and may be registered in the United States and/or other countries. All other trademarks are the property of their respective owners. Hypertherm is in no way affiliated with Kjellberg. © 6/10 Hypertherm, Inc. Revision 1 880750

8. 9.

Reference number T902Y T012Y T101 T102 T104 T2115Y T2120Y T2125Y T2127Y T2130Y T3030 T3045 T3060 T521 T522 V522 V501 V502 T502 V4335 V4345

Article number .11.844.901.152 .11.844.921.300 .11.836.921.153 .11.836.921.154 .11.836.921.1542 .11.846.921.415 .11.846.921.420 .11.846.921.425 .11.846.921.427 .11.846.921.430 .11.836.901.163 .11.836.901.164 .11.836.901.165 .11.836.901.271 .11.836.921.271 .11.833.121.271 .11.833.101.261 .11.833.121.261 .11.841.721.081 .11.833.101.155 .11.833.101.157

Description Water tube SilverLine electrode Gas guide, 6x0.8, cw Gas guide, 3x0.6, cw Gas guide, 3x0.4, cw CoolFlow nozzle, 120 amp CoolFlow nozzle, 200 amp CoolFlow nozzle, 250 amp CoolFlow nozzle, 300 amp CoolFlow nozzle, 360 amp Nozzle cap, 30° Nozzle cap, 45° Nozzle cap, 60° Swirl gas nozzle, PB-S80 Swirl gas nozzle, PB-S80 Swirl gas nozzle, PerCut 370.2 Protective cap, PB-S80 Protective cap, PB-S80 Protective cap, PerCut 370.2 Swirl gas cap, 3.5 Swirl gas cap, 4.5

Centricut number C117-152 C117-1300 C117-153 C117-154 C117-542 C117-415 C117-420 C117-425 C117-427 C117-430 C117-163 C117-164 C117-165 C117-271 C117-0271 C117-1271 C53-261 C117-261 C117-081 C117-155 C117-157

Powermax Selection Guide Centricut consumables for Kjellberg ®

Hypertherm, Inc. Hanover, NH 03755 USA 603-643-3441 Tel Hypertherm Europe B.V. 4704 SE Roosendaal, Nederland 31 165 596907 Tel

Hypertherm (Shanghai) Trading Co., Ltd. PR China 200052 86-21 5258 3330 /1 Tel

Hypertherm (India) Thermal Cutting Pvt. Ltd. Chennai, Tamil Nadu 91 0 44 2834 5361 Tel

Hypertherm (S) Pte Ltd. Singapore 349567 65 6 841 2489 Tel

Hypertherm Brasil Ltda. Guarulhos, SP - Brasil 55 11 2409 2636 Tel

Hypertherm México, S.A. de C.V. México, D.F. 52 55 5681 8109 Tel

finefocus 800 plus  

finefocus 800 plus parts

Read more
Read more
Similar to
Popular now
Just for you