Page 1

TWO COMPONENT • ACRYLIC POLYMER MODIFIED TOPPING AND UNDERLAYMENT • OVERHEAD AND WALL REPAIRS

RAMPATCH *Bonds to Virtually Any Concrete Surface *Light Gray to Blend with Existing Concrete *Improved Bond and Compressive Strength PRODUCT DESCRIPTION

PRODUCT FEATURES

RAMPATCH is a two component polymer modified concrete repair, topping, and underlayment material. The RAMPATCH liquid is a high solids content Acrylic Polymer. The RAMPATCH Powder #RM1005 is a portland cement based mix with graded silica and special chemical additives. Polymer modified concrete gives improved bonding, improved chemical resistance, improved water resistance and improved tensile, compressive and flexural strengths.

This high strength portland cement/acrylic polymer combination provides a smooth durable semi-resilient surface which can be used as a finished floor in most applications. RAMPATCH is easy to mix and apply, requiring no special tools. It is suitable for use as a screedable topping and underlayment, or as a floor, wall or overhead repair material when mixed to a stiffer trowelable consistency. RAMPATCH has been approved by the USDA for use in most processing plants and may be used where there is exposure to potable water. Use of RAMPATCH can help your project earn LEED Credits. Contact factory for details.

PRODUCT APPLICATIONS RAMPATCH is designed to be used both as a topping or underlayment and as a wall, floor, and overhead patching and repair material when mixed to a stiffer consistency. For use as an underlayment, mix to the consistency of a thick pancake batter. Use RAMPATCH to level and smooth rough or rained on concrete. RAMPATCH may be used to level low areas inside or outside. It will bond to and may be used to level virtually any concrete surface. Mixed as a repair material, RAMPATCH may be used to repair walls, floors, tilt panels, driveways, sidewalks, precast members, etc. RAMPATCH may be applied from featheredge to 2-1/2 inches. Suitable for interior or exterior applications. Suitable for application where there is rubber tired forklift and vehicle traffic.

         

Outstanding Bonding Improved Water Resistance Interior or Exterior Use From Featheredge to 2-1/2 inches May Be Used as Screedable Underlayment May Be Used as a Trowelable Repair Material Improved Compressive Strength No Moist Curing Required High Solids Acrylic Polymer May Be Stained or Used With Integral Color May Be Used for Stenciled and Decorative Concrete LEED Credits Applicable

PRODUCT TEST RESULTS WORKING TIME: Approximately 25 minutes COLOR: Light Gray, also available in White INITIAL SET: 4 Hours SCREEDABLE CONSISTENCY: (1 bag to 1 gallon) Compressive Strength (ASTM C-109, Air Cured) 7 Days - 4120 PSI 28 Days - 5500 PSI

Flexural Strength (ASTM C-348, Air Cured) 7 Days - 1260 PSI 28 Days - 1535 PSI

Slant Shear Bond (ASTM C-1042, Air Cured) 28 Days - 1250 PSI TROWELABLE CONSISTENCY: (1 bag to .8 gallon) Compressive Strength (ASTM C-109, Air Cured) 7 Days - 4550 PSI 28 Days - 6000 PSI

Flexural Strength (ASTM C-348, Air Cured) 7 Days - 1360 PSI 28 Days - 1720 PSI

Slant Shear Bond (ASTM C-1042, Air Cured) 28 Days - 1550 PSI


SURFACE PREPARATION - All surfaces must be clean and structurally sound; free of dust, grease, oil, paint, sealers, etc. Pores of the concrete surface must be open to permit proper bonding, especialy on fresh “green” concrete. Any necessary surface preparation may be done by shotblasting, scarifying, sandblasting or acid etching. If acid etch is used, be sure to neutralize surface, clean and brush thoroughly. For heavy traffic applications, mechanical abrasion of the surface is recommended. Concrete surfaces should be surface saturated but dry to touch (SSD). Do not bridge cracks with RAMPATCH. They will “telegraph” through. Fill cracks prior to placement of RAMPATCH. Expansion joints should be extended through the RAMPATCH. For surfaces with low porosity, an EPOXY PRIMER can be used per installation instructions on the literature. MIXING - RAMPATCH may be mixed in a mortar mixer, with a heavy duty low-to-medium speed drill or by hand. Always use a clean mixing container. Place RAMPATCH Acrylic #RM1003 in container and add RAMPATCH Powder #RM1005, mixing while adding powder. DO NOT ADD WATER. Added water will reduce strength and bonding. Mix for 2 to 3 minutes until a smooth, lumpfree mixture is obtained. Mixing time should not exceed 3 minutes. DO NOT OVERMIX and DO NOT entrap air while mixing. USE OF AGGREGATE - For areas with a thickness over 1/2”, aggregate should be added to RAMPATCH. Add 1 part by volume of 3/8” pea gravel to 2 parts by volume of RAMPATCH. DO NOT ADD WATER. USE AS UNDERLAYMENT OR TOPPING - For use as an underlayment, mix to desired screedable consistency, no more liquid than 1 bag to 1 gallon of polymer. As an underlayment, apply from featheredge to 2-1/2”. Material may be screeded for low places or spread into place with a squeegee. When using as a wearing surface topping, install at least 3/8” thick. DO NOT FEATHEREDGE as a wearing surface topping. For areas over 1/2” in depth aggregate is required. USE AS A TROWELABLE NON-SAG REPAIR MATERIAL- For floor, wall and overhead repairs, mix about 3/4 to 7/8 of liquid polymer to a bag of powder to get a stiffer, trowelable non-sag consistency. Make a trial batch to get desired consistency. Lubricate trowel with polymer to prevent dragging. For wall applications such as coating or filling concrete block, RAMPATCH may be applied with a hopper gun and then floated smooth. INSTALLATION - To insure proper bonding, use RAM-PRIMER or apply a bond slurry coat scrubbed into the surface. The RAMPRIMER will give more reliable and consistent results. Allow the RAM-PRIMER to dry (30-45 minutes) and install RAMPATCH material. Material may be applied up to 24 hours after the RAM-PRIMER. The RAM-PRIMER will re-emulsify one time and may be used for inside and outside applications.

The bond slurry coat is a syrup-like consistency mix of RAMPATCH Powder and RAMPATCH Acrylic. Scrub the slurry coat into the SSD surface. Place RAMPATCH and smooth and spread while slurry coat is still damp. DO NOT LET SLURRY COAT DRY. Screed off to get a smooth flat surface. Use a trowel for touch-up and featheredging. DO NOT OVERTROWEL. Lubricate trowel with polymer to prevent dragging. The #RM1003 RAMPATCH Acrylic makes the materials darker. Less polymer will give a lighter finished surface. For best results, smooth and spread into place and touch-up as needed. A latex film will form when RAMPATCH begins to set. This is normal and will disappear. Normally floor coverings may be applied the next day. With thick applications or cold or damp weather, another day may be required. No heavy traffic should be permitted for 4 to 5 days. When used as an underlayment, always follow the directions of floor covering manufacturers concerning maximum moisture content and perform required tests. Over interior plywood floors, use two coats of RAM-PRIMER applied at right angles. Allow RAM-PRIMER to dry between coats. Floor must be rigid and sound. Anchor metal lathe into wood. This will help hold the RAMPATCH in place. RAMPATCH is more resistant to moisture penetration than regular concrete. Breathable water based sealers may be applied over RAMPATCH as soon as 24 hours. Paints and coatings may be applied over RAMPATCH as you would over concrete. For solvent based sealers and coatings, wait 3-4 days for the RAMPATCH to harden. For non-breathable coatings, ensure moisture has left RAMPATCH. A simple poly test can be performed over the deepest areas. Always follow manufacturer recommendations and testing for applying over fresh concrete. PRECAUTIONS - Do not use below 40oF. The best temperature to use is 60o-90oF. DO NOT LET RAMPATCH ACRYLIC #RM1003 FREEZE. Always make a trial installation first under actual job conditions to be sure you get the desired results before using on larger areas. CONTAINS SILICA SAND AND FREE SILICA. Do not breathe dust. Avoid inhalation by wearing respirator. Continuous exposure and inhalation may cause silicosis and crystalline silica is classified as a known human carcinogen. CURING - In general, RAMPATCH will air cure without any need for curing products. However, care should be taken in areas where RAMPATCH is exposed to wind or direct sunlight, sometimes these can cause cracking as the top dries before the bottom has cured. For these fast drying situations, the RAMPATCH should be covered with damp burlap or plastic for 48 hours. COVERAGE - RAMPATCH Powder #RM1005 is packaged in 45 lb. moisture resistant bags. RAMPATCH Acrylic #RM1003 is packaged in 1 gallon jugs, 4 to a carton. One 45 lb. bag of RAMPATCH Powder #RM1005 and one gallon of RAMPATCH Acrylic #RM1003 will cover 45 sq. ft. at 1/8” thickness.

CONTAINS PORTLAND CEMENT. Avoid eye contact or prolonged contact with skin. Wash thoroughly after handling. In case of eye contact, flush with plenty of water for at least 15 minutes. Consult a physician immediately. Keep out of the reach of children.

LIMITED WARRANTY

Lyons Manufacturing, Inc. warrants the high quality of its products. However, because of many factors beyond our control in their use, such as job conditions, workmanship, etc., the liability of all parties making and selling this product is expressly limited to the refund of the purchase price or replacement of the Lyons material used. Lyons Manufacturing, Inc. will replace any product proven to have a manufacturing defect, FOB Factory, provided Lyons Manufacturing, Inc. is notified of such defect within one (1) year from the date of shipment from the factory. This warranty is in lieu of all other warranties, express or implied. Lyons Manufacturing, Inc. makes no warranty of suitability of its products for any particular application and sells its products upon the condition that customer shall conduct their own test to determine the suitability of the products for their purposes. Under no circumstances will Lyons Manufacturing, Inc. be liable for economic, special, incidental or consequential damages or losses of any kind.

LYONS MANUFACTURING, INC. 8900 Forney Road  Dallas, TX 75227-4505  214/381-8100 www.lyonsmanufacturing.com 05 17


44.3.11

Page: 1/10

Safety Data Sheet

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

1 Identification · Product identifier · Trade name: RamPatch · Other means of identification: No other identifiers · Recommended use and restriction on use · Recommended use: Concrete surfacer · Restrictions on use: No relevant information available. · Details of the supplier of the Safety Data Sheet · Supplier: Ram Tool Construction Supply Co. 3620 8th Avenue South Birmingham, AL 35222 Phone: (205) 714-3300 E-mail: information@ram-tool.com Web Site: https://ram-tool.com/ · Manufacturer: Lyons Manufacturing, Inc 8900 Forney Rd Dallas, TX 75227 (214) 381-8100 · Emergency telephone number: ChemTel Inc. (800)255-3924 (North America) +1 (813)248-0585 (International)

2 Hazard(s) identification · Classification of Skin Irrit. 2 H315 Eye Dam. 1 H318 Skin Sens. 1 H317 Carc. 1A H350 STOT SE 3 H335

the substance or mixture Causes skin irritation. Causes serious eye damage. May cause an allergic skin reaction. May cause cancer. Route of exposure: Inhalation. May cause respiratory irritation.

· Label elements · GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS). · Hazard pictograms:

GHS05 GHS07 GHS08 · Signal word: Danger · Hazard statements: H315 Causes skin irritation. H318 Causes serious eye damage.

(Cont'd. on page 2)


44.3.11

Page: 2/10

Safety Data Sheet

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch (Cont'd. of page 1)

H317 May cause an allergic skin reaction. H350 May cause cancer. Route of exposure: Inhalation. H335 May cause respiratory irritation. · Precautionary statements: P201 Obtain special instructions before use. P202 Do not handle until all safety precautions have been read and understood. P261 Avoid breathing dust. P264 Wash thoroughly after handling. P271 Use only outdoors or in a well-ventilated area. P280 Wear protective gloves/protective clothing/eye protection. P302+P352 IF ON SKIN: Wash with plenty of water. P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P308+P313 IF exposed or concerned: Get medical advice/attention. P362+P364 Take off contaminated clothing and wash it before reuse. P403+P233 Store in a well-ventilated place. Keep container tightly closed. P501 Dispose of contents/container in accordance with local/regional/national/international regulations. · Other hazards There are no other hazards not otherwise classified that have been identified.

3 Composition/information on ingredients · Chemical characterization: Mixtures · Components: 14808-60-7 Quartz (SiO2) 60-80% Carc. 1A, H350 65997-15-1 Cement, portland, chemicals 20-40% Eye Dam. 1, H318 Skin Irrit. 2, H315; Skin Sens. 1, H317; STOT SE 3, H335 92704-41-1 Kaolin, calcined 1-5% · Additional information: For the listed ingredient(s), the identity and/or exact percentage(s) are being withheld as a trade secret. For the wording of the listed Hazard Statements refer to section 16.

4 First-aid measures · Description of first aid measures · After inhalation: Supply fresh air; consult doctor in case of complaints. Provide oxygen treatment if affected person has difficulty breathing. In case of irregular breathing or respiratory arrest provide artificial respiration. · After skin contact: Brush off loose particles from skin. Immediately remove any clothing soiled by the product. Immediately wash with water and soap and rinse thoroughly.

(Cont'd. on page 3)


44.3.11

Page: 3/10

Safety Data Sheet

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch If skin irritation continues, consult a doctor. · After eye contact: Protect unharmed eye. Remove contact lenses if worn. Rinse opened eye for several minutes under running water. Then consult a doctor. · After swallowing: Rinse out mouth and then drink plenty of water. Do not induce vomiting; immediately call for medical help. · Most important symptoms and effects, both acute and delayed: Coughing Breathing difficulty Allergic reactions Irritant to skin and mucous membranes. Strong irritant with the danger of severe eye injury. May cause respiratory irritation. Gastric or intestinal disorders when ingested. Nausea in case of ingestion. · Danger: May cause cancer. Route of exposure: Inhalation. Danger of impaired breathing. · Indication of any immediate medical attention and special treatment needed: Medical supervision for at least 48 hours. If necessary oxygen respiration treatment. Treat skin and mucous membrane with antihistamine and corticoid preparations. Contains Cement, portland, chemicals. May produce an allergic reaction.

(Cont'd. of page 2)

5 Fire-fighting measures · Extinguishing media · Suitable extinguishing agents: The product is not flammable. Use fire fighting measures that suit the environment. · For safety reasons unsuitable extinguishing agents: None. · Special hazards arising from the substance or mixture Formation of toxic gases is possible during heating or in case of fire. · Advice for firefighters · Protective equipment: Wear self-contained respiratory protective device. Wear fully protective suit.

6 Accidental release measures · Personal precautions, protective equipment and emergency procedures Use respiratory protective device against the effects of fumes/dust/aerosol. Wear protective equipment. Keep unprotected persons away. Avoid formation of dust.

(Cont'd. on page 4)


44.3.11

Safety Data Sheet

Page: 4/10

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch · Environmental precautions Do not allow to enter sewers/ surface or ground water. Damp down dust with water spray. · Methods and material for containment and cleaning up Pick up mechanically. Send for recovery or disposal in suitable receptacles. · Reference to other sections See Section 7 for information on safe handling. See Section 8 for information on personal protection equipment. See Section 13 for disposal information.

(Cont'd. of page 3)

7 Handling and storage · Handling · Precautions for safe handling: Use only in well ventilated areas. Prevent formation of dust. Any deposit of dust which cannot be avoided must be regularly removed. Avoid contact with the eyes and skin. Keep out of reach of children. Do not breathe dust. · Information about protection against explosions and fires: Keep respiratory protective device available. · Conditions for safe storage, including any incompatibilities · Storage · Requirements to be met by storerooms and receptacles: Store only in the original receptacle. Protect from humidity and water. Store in cool, dry conditions in well sealed receptacles. · Information about storage in one common storage facility: Store away from foodstuffs. Do not store together with acids. · Specific end use(s) No relevant information available.

8 Exposure controls/personal protection · Control parameters · Components with limit values that require monitoring at the workplace: 14808-60-7 Quartz (SiO2) REL (USA) Long-term value: 0.05* mg/m³ *respirable dust; See Pocket Guide App. A TLV (USA) Long-term value: 0.025* mg/m³ *as respirable fraction (Cont'd. on page 5)


44.3.11

Safety Data Sheet

Page: 5/10

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch EL (Canada)

Long-term value: 0.025 mg/m³ ACGIH A2; IARC 1 EV (Canada) Long-term value: 0.10* mg/m³ *respirable fraction LMPE (Mexico) Long-term value: 0.025* mg/m³ A2, *fracción respirable 65997-15-1 Cement, portland, chemicals PEL (USA) Long-term value: 50 mppcf or 15* 5** mg/m³ *total dust **respirable fraction REL (USA) Long-term value: 10* 5** mg/m³ *total dust **respirable fraction TLV (USA) Long-term value: 1* mg/m³ E; *as respirable fraction EL (Canada) Long-term value: 10* 3** mg/m³ *total dust;**respirable fraction EV (Canada) Long-term value: 10(D) mg/m³ total dust LMPE (Mexico) Long-term value: 1* mg/m³ A4, *fracción respirable 92704-41-1 Kaolin, calcined EL (Canada) Long-term value: 2 mg/m³ EV (Canada) Long-term value: 2(D) mg/m³ respirable LMPE (Mexico) Short-term value: 20 mg/m³ Long-term value: 10 mg/m³ (j), A4

(Cont'd. of page 4)

· Exposure controls · Personal protective equipment: · General protective and hygienic measures: The usual precautionary measures for handling chemicals should be followed. Keep away from foodstuffs, beverages and feed. Immediately remove all soiled and contaminated clothing. Wash hands before breaks and at the end of work. Do not inhale dust / smoke / mist. Avoid contact with the eyes and skin. · Engineering controls: No relevant information available. · Breathing equipment: Dust mask recommended. Particulate mask should filter at least 99% of airborne particles. Use suitable respiratory protective device in case of insufficient ventilation. For spills, respiratory protection may be advisable. · Protection of hands: Protective gloves (Cont'd. on page 6)


44.3.11

Page: 6/10

Safety Data Sheet

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch (Cont'd. of page 5)

The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. · Eye protection: Safety glasses · Body protection: Protective work clothing · Limitation and supervision of exposure into the environment No relevant information available.

9 Physical and chemical properties · Information on basic physical and chemical properties · Appearance: Form: Powder Color: Light grey · Odor: Odorless · Odor threshold: Not determined. · pH-value: · Melting point/Melting range: · Boiling point/Boiling range:

10 - 12 (in solution) Not determined. Not determined.

· Flash point:

Not applicable.

· Flammability (solid, gaseous):

Product is not flammable.

· Auto-ignition temperature:

Not applicable.

· Decomposition temperature:

Not determined.

· Danger of explosion:

Product does not present an explosion hazard.

· Explosion limits Lower: Upper: · Oxidizing properties:

Not determined. Not determined. Non-oxidizing.

· Vapor pressure:

Not applicable.

· Density: Relative density: Vapor density: Evaporation rate:

Not determined. Not applicable. Not applicable.

· Solubility in / Miscibility with Water:

Partly soluble.

· Partition coefficient (n-octanol/water): Not determined. · Viscosity Dynamic: Kinematic:

Not applicable. Not applicable. (Cont'd. on page 7)


44.3.11

Page: 7/10

Safety Data Sheet

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch (Cont'd. of page 6)

· Other information

No relevant information available.

10 Stability and reactivity · Reactivity: No relevant information available. · Chemical stability: · Thermal decomposition / conditions to be avoided: No decomposition if used and stored according to specifications. · Possibility of hazardous reactions Toxic fumes may be released if heated above the decomposition point. Exothermic reaction with acids. Reacts with certain metals. Reacts with strong oxidizing agents. · Conditions to avoid Avoid acids. · Incompatible materials No relevant information available. · Hazardous decomposition products Possible in traces.

11 Toxicological information · Information on toxicological effects · Acute toxicity: · LD/LC50 values that are relevant for classification: None. · Primary irritant effect: · On the skin: Irritant to skin and mucous membranes. · On the eye: Strong irritant with the danger of severe eye injury. · Sensitization: Sensitization possible through skin contact. Contains Cement, portland, chemicals. May produce an allergic reaction. · Carcinogenic categories · IARC (International Agency for Research on Cancer): 14808-60-7 Quartz (SiO2)

1

· NTP (National Toxicology Program): 14808-60-7 Quartz (SiO2)

K

· OSHA-Ca (Occupational Safety & Health Administration): None of the ingredients are listed. · Probable route(s) of exposure: Inhalation. Eye contact. Skin contact. · Germ cell mutagenicity: Based on available data, the classification criteria are not met. · Carcinogenicity: May cause cancer. Route of exposure: Inhalation. · Reproductive toxicity: Based on available data, the classification criteria are not met. · STOT-single exposure: May cause respiratory irritation.

(Cont'd. on page 8)


44.3.11

Page: 8/10

Safety Data Sheet

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch · STOT-repeated exposure: Based on available data, the classification criteria are not met. · Aspiration hazard: Based on available data, the classification criteria are not met.

(Cont'd. of page 7)

12 Ecological information · Toxicity · Aquatic toxicity No relevant information available. · Persistence and degradability No relevant information available. · Bioaccumulative potential: No relevant information available. · Mobility in soil: No relevant information available. · Additional ecological information · General notes: Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system. Rinse off of bigger amounts into drains or the aquatic environment may lead to increased pH-values. A high pH-value harms aquatic organisms. In the dilution of the use-level the pH-value is considerably reduced, so that after the use of the product the aqueous waste, emptied into drains, is only low waterdangerous. · Other adverse effects No relevant information available.

13 Disposal considerations · Waste treatment methods · Recommendation: Contact waste processors for recycling information. The user of this material has the responsibility to dispose of unused material, residues and containers in compliance with all relevant local, state and federal laws and regulations regarding treatment, storage and disposal for hazardous and nonhazardous wastes. · Uncleaned packagings · Recommendation: Disposal must be made according to official regulations.

14 Transport information · UN-Number · DOT, ADR, IMDG, IATA

Not regulated.

· UN proper shipping name · DOT, ADR, IMDG, IATA

Not regulated.

· Transport hazard class(es) · DOT, ADR, IMDG, IATA · Class

Not regulated. (Cont'd. on page 9)


44.3.11

Safety Data Sheet

Page: 9/10

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch (Cont'd. of page 8)

· Packing group · DOT, ADR, IMDG, IATA

Not regulated.

· Environmental hazards · Marine pollutant:

No

· Special precautions for user

Not applicable.

· Transport in bulk according to Annex II of

MARPOL73/78 and the IBC Code

Not applicable.

15 Regulatory information · Safety, health and environmental regulations/legislation specific for the substance or

mixture

· United States (USA) · SARA · Section 302 (extremely hazardous substances): None of the ingredients are listed. · Section 304 (emergency release notification): None of the ingredients are listed. · Section 355 (extremely hazardous substances): None of the ingredients are listed. · Section 313 (Specific toxic chemical listings): None of the ingredients are listed. · TSCA (Toxic Substances Control Act) All ingredients are listed. · Proposition 65 (California) · Chemicals known to cause cancer: 14808-60-7 Quartz (SiO2) · Chemicals known to cause reproductive toxicity for females: None of the ingredients are listed. · Chemicals known to cause reproductive toxicity for males: None of the ingredients are listed. · Chemicals known to cause developmental toxicity: None of the ingredients are listed. · Carcinogenic categories · EPA (Environmental Protection Agency): None of the ingredients are listed. · IARC (International Agency for Research on Cancer): 14808-60-7 Quartz (SiO2)

1 (Cont'd. on page 10)


44.3.11

Safety Data Sheet

Page: 10/10

acc. to OSHA HCS (29 CFR 1910.1200) Printing date: May 16, 2017

Revision: May 16, 2017

Trade name: RamPatch (Cont'd. of page 9)

· NIOSH-Ca (National Institute for Occupational Safety and Health): 14808-60-7 Quartz (SiO2)

16 Other information This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. · Date of preparation / last revision May 16, 2017 / · Abbreviations and acronyms:

ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road IMDG: International Maritime Code for Dangerous Goods DOT: US Department of Transportation IATA: International Air Transport Association CAS: Chemical Abstracts Service (division of the American Chemical Society) LC50: Lethal concentration, 50 percent LD50: Lethal dose, 50 percent NIOSH: l'Institut national de recherche sur la sécurité et la santé au travail / National Institute for Occupational Safety (États-Unis) OSHA: Occupational Safety & Health Administration TLV: Threshold Limit Value PEL: Permissible Exposure Limit REL: Recommended Exposure Limit Skin Irrit. 2: Skin corrosion/irritation – Category 2 Eye Dam. 1: Serious eye damage/eye irritation – Category 1 Skin Sens. 1: Skin sensitisation – Category 1 Carc. 1A: Carcinogenicity – Category 1A STOT SE 3: Specific target organ toxicity (single exposure) – Category 3

· Sources Website, European Chemicals Agency (echa.europa.eu) Website, US EPA Substance Registry Services (ofmpub.epa.gov/sor internet/registry/substreg/home/ overview/home.do) Website, Chemical Abstracts Registry, American Chemical Society (www.cas.org) Patty's Industrial Hygiene, 6th ed., Rose, Vernon, ed. ISBN: 978-0-470-07488-6 Casarett and Doull's Toxicology: The Basic Science of Poisons, 8th Ed., Klaasen, Curtis D., ed., ISBN: 978-0-07-176923-5. Safety Data Sheets, Individual Manufacturers SDS Prepared by: ChemTel Inc. 1305 North Florida Avenue Tampa, Florida USA 33602-2902 Toll Free North America 1-888-255-3924 Intl. +01 813-248-0573 Website: www.chemtelinc.com

Profile for Ram Tool Construction Supply Co.

RamPatch Tech Data & SDS  

RamPatch Tech Data & SDS