Hanger Options HANGER OPTIONS HTU See Hanger Options General Notes. SKEWED SEAT • Skewable up to 67 1⁄2°. • Available in single and 2-ply size. • No bevel cut required. “A” Flange Acute Side “A” Flange Allowable Loads for Skewed HTU Hangers Model No. HTU26 HTU28 HTU210 HTU26-2 HTU28-2 HTU210-2 Skew Angle (Degree) < 51 51-67 1⁄2 < 51 51-67 1⁄2 < 51 51-67 1⁄2 < 51 51-67 1⁄2 < 51 51-67 1⁄2 < 51 51-67 1⁄2 Fasteners Carrying Member 20-16d 20-16d 26-16d 26-16d 32-16d 32-16d 20-16d 20-16d 26-16d 26-16d 32-16d 32-16d Carried Member 14-10dx1 1⁄2 12-10dx1 1⁄2 20-10dx1 1⁄2 17-10dx1 1⁄2 26-10dx1 1⁄2 22-10dx1 1⁄2 14-10d 12-10d 20-10d 17-10d 26-10d 22-10d 1. Uplift loads have been increased for wind or earthquake loading with no further increase allowed. Reduce where other loads govern. 2. Allowable downloads may not be increased. DFL/SP Allowable Loads1,2 HF/SPF Allowable Loads1,2 Uplift (133/160) 1315 970 2015 1485 2715 2005 1335 1110 2470 1710 3600 2255 Uplift (133/160) 1130 835 1730 1280 2335 1725 1145 955 2120 1470 3100 1940 Download (100/115/125) 2945 2595 3060 2815 3175 3040 2555 2700 3890 3775 4935 4790 Download (100/115/125) 2530 2230 2630 2420 2730 2615 2200 2320 3345 3245 4245 4120 3. Maximum hanger gap between end of joist (truss) and face of carrying member is 1⁄8". 4. Nails: 16d = 0.162" dia. x 3 1⁄2" long, 10dx1 1⁄2 = 0.148" dia. x 1 1⁄2" long, 10d = 0.148" dia. x 3" long. See page 22-23 for other nail sizes and information. Specify Angle Top View HTU Hanger Skewed Right < 51° Specify Angle 51° to 67¹⁄₂° Top View HTU Hanger Skewed Right ≥ 51° HGUS/HHUS HGUS – SKEWED SEAT • HGUS hangers can be skewed only to a maximum of 45o. Allowable loads are: HGUS Seat Width W < 2" 2" < W < 6" 2" < W < 6" W > 6" Joist bevel or square cut bevel cut square cut bevel cut THJU See Hanger Options General Notes. HANGER WIDTHS • THJU is available in intermediate seat widths between 5 1⁄8" (THJU26 width) and 8 1⁄8" (THJU26-W width). • Allowable download and uplift for all intermediate widths is 100% of the THJU26-W table loads. • For double hip installation, divide the total allowable load by 2 to determine the allowable load for each hip. • Order as THJU26X and specify width; see table for reference. Down Load 0.62 of table load 0.67 of table load 0.46 of table load 0.40 of table load Acute Side Specify Angle Top View HHUS Hanger Skewed Right (joist must be bevel cut) All joist nails installed on the outside angle (non-acute side). Uplift 0.46 of table load 0.41 of table load 0.41 of table load 0.41 of table load THJU Intermediate Width Options Carried Member Combination Hip Skew 2-Ply Hip and Single-Ply Jack 45-degree 6 3⁄8 Single-Ply Hip and 2-Ply Jack 45-degree 6 3⁄4 Double (Terminal) Hip 45-degree 7 3⁄8 2-Ply Hip and 2-Ply Jack 45-degree Use THJU26-W 44°- 46° Use THJU26 47°- 49° 5 1⁄2 50°- 52° 5 3⁄4 Single-Ply Hip and Single-Ply Jack Width (W) Hip Skew 53°- 55° 6 W 56°- 57° 6 3⁄8 58°- 59° 6 5⁄8 THJU Top View Installation 60°- 61° 7 62°- 63° 7 3⁄8 64°- 65° Use THJU26-W Hanger Options C-2013 © 2013 SIMPSON STRONG-TIE COMPANY INC. PRINTED 12/12 See Hanger Options General Notes. HHUS – SLOPED AND/OR SKEWED SEAT • HHUS hangers can be skewed to a maximum of 45° and/or sloped to a maximum of 45°. • For skew only, maximum allowable download is 0.85 of the table load. • For sloped only or sloped and skewed hangers, the maximum allowable download is 0.65 of the table load. • Uplift loads for sloped/skewed conditions are 0.72 of the table load, not to exceed 2475 lbs. • The joist must be bevel-cut to allow for double shear nailing. 219