SOCIAL DISTANCER (CART DIVIDER) from TYPHOON GOLF

DOUBLE

PUT

SINGLE RIDER RULES

YOUR

REVENUE .. .

DIVIDE YOUR CARTS

BEHIND YOU

GOLF CART

GOLF CART

DIVIDERS

DIVIDERS

CART DIVIDERS

30” GOLF CART

DIVIDERS

Adjustable Height 38”- 42.5”

• No more “One Rider per Cartâ€? Rule • Gets more golfers out on the course • Increases cart and green fee revenues • Adjustable height fits most cart models

BUSINESS BENEFITS

Double your revenue by dividing your carts

• Easy to install (and easy to remove) • Won’t damage carts • Provides Social Distancing for your customers • Lets buddies ride together

CUSTOMIZATION 2 TURN TO FIT

1 MEASURE

3 TURN CHART HEIGHT

1/4 TURN

42.50�

41.75�

41.00�

40.25“ 39.50�

38.75�

38.00�

Preset 1 2 3 4 5 6

MEASURE HERE

The Social Distancer is designed to fit golf carts with heights from seat to| roof of between 38� and 42.5�.

It comes preset at 42.5� height, the maximum height. The height can easily be shortened in increments of ž�. ***

Measure the distance from the rear of seat cushion perpendicularly to the roof.

Determine from the chart how many turns of the bar you will need that is closest to your desired height.

NOTE: Your package comes with a piece of two-sided tape

How to modify the height

1. Place the Social Distancer on a flat surface with the Upper Bar (the one without Velcro) closest to you

2. Roll the bar over the screen towards the bottom by one quarter of a turn for each ž� you need to shorten the height.

(If the height is fine at preset 42.5� go to #3)

3. Peel the covering off the adhesive back of both sides of the two-sided tape and stick it between the screen and the bar such that it holds the bar in desired position.

THAT’S IT. YOU ARE READY TO GO TO THE INSTALLATION

INSTALLATION Be sure the height is adjusted to your cart before installing.

B

A

Y

1. Clear 30 gauge vinyl screen [X] 2. Two stabilizer bars [Y&Z] 3. Two sticky-back bolts [A&B] LOOSE 4. One long loop with “nub� [C] at end 5. One hook strap stuck to top of lower bar [C] 6. One long loop strap stuck at front under bar [C] 7. One self-adhesive hook attached to [D] 8. One two-sided clear tape (for customization) LOOSE

X

PARTS

GOLF CART

DIVIDERS

Adjustable Height 38�- 42.5�

ASSEMBLY

A. Stick Upper bar to roof with bolts [A&B] B. Lift seat and pinch [C] under & behind seat C. Attach [C] to lower bar D. Stick [D] under seat

30�

D

Z

C

Note: “Stick� means peel off adhesive back while “Attach� means join Hook & Loop together.

1. Peel adhesive covers off one Sticky Back Bolt (A) 2. Stick Sticky Bolt (A) to the roof in the center (side to side) of the cart with the front edge on the point that you marked perpendicular to the seat in the customization measurement 3. Peel adhesive cover off the second Sticky Back Bolt (B) 4. Insert Bolt B into hole in the front of bar, then insert Bolt (A), which is attached to roof, thru the hole in the rear of the bar, move bar into desired position and stick Bolt B to the roof in center of the cart.

5. Use Nuts to attach the Bar to both Bolts (A&B)

6. Tilt seat forward and put the end of the Long Loop strap C1 with the white “nub� into the battery compartment under the seat, then close seat down to pinch Loop Strap C1 so it won’t pull out of battery compartment.

7. Attach Loop strap C1 to the Hook strap (C2) on the TOP surface of the bottom bar 8. Remove Hook Strap D1 and Peel the adhesive back off it.

9. Stick Hook Strap D1 to the cart under the front of the seat such that it runs perpendicular to the floor in center of cart (or just beside shift) 10. Attach the long Loop strap D2 that is attached, with Velcro and a screw, to the lower bar to Hook Strip D1 so it pulls down snug and aligns the screen perpendicular to the seat 11. Trim off excess lengths on seat Loop straps (C&D).