MF00310%3AIndustrial+power+feeder+SM-REF013_Ing_Ver_00-06

Band saw feeding devices

SR-013

English

BAND SAW FEEDING DEVICES Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Via Montale, 11 - 41030 Rovereto s/Secchia - Modena - Italy

Instruction handbook and recommended spare parts

SR - 013 SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

1

Band saw feeding devices

SR-013

Via Montale,11 - 41030 Rovereto s/Secchia (Modena) Tel. 0039 (059) 673003 Fax. 0039 (059) 673007

Instruction handbook and recommended spare parts

SR - 013 Commer cial: Commercial:

Ver. 00/FB/06

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

English : Customer

Serial number:

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

2

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Contents

0

1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10

Information/Introduction Warranty .............................................................................. Pag. 4 General test and inspection .................................................. Pag. 4 Warnings .............................................................................. Pag. 4÷5 Description ........................................................................... Pag. 5 Use of the machinery for its intended purposes ................... Pag. 6 Uses falling outside the intended purposes .......................... Pag. 6 Technical specifications ....................................................... Pag. 7 Storing conditions ................................................................ Pag. 8 Machinery disposal .............................................................. Pag. 8 Overall dimensions ............................................................... Pag. 8

2

Machinery identifying data ................................................. Pag. 9

3 3.1 3.2 3.3 3.4 3.5 3.6 3.7

Normal safety conditions - safety standards Introduction ......................................................................... Pag. 10 Definitions ............................................................................ Pag. 10÷11 General safety standards ...................................................... Pag. 11÷12 General indications ............................................................... Pag. 12÷14 Specific indications .............................................................. Pag. 14 Safety equipment ................................................................. Pag. 14 Explanation of symbols ........................................................ Pag. 16÷17

4 4.1 4.2 4.3 4.4

Installation/Connections Machinery lifting and handling ............................................. Pag. 18 Machinery positioning .......................................................... Pag. 19÷20 Electrical connection ............................................................ Pag. 21÷23 Pneumatic connection .......................................................... Pag. 23

5 5.1 5.2 5.3 5.4 5.5

Use Controls and regulators ........................................................ Pag. 25÷27 Pre-setting of the standard machine .................................... Pag. 28÷29 Pre-setting of the pneumatic model ..................................... Pag. 29÷31 Use ....................................................................................... Pag. 32÷33 Use of the pneumatic feeding device .................................... Pag. 34÷35

6

Trouble-shooting guide and possible remedies ................. Pag. 36

7 7.1 7.2 7.3 7.4

Maintenance Safety conditions (safety standard) ...................................... Pag. 37 Daily maintenance ................................................................ Pag. 37 Weekly maintenance ............................................................ Pag. 37 Monthly maintenance ........................................................... Pag. 37

Annexes : ❏ - Spare Parts Catalogue ❏ - Lay-out of safety devices ❏ - Pneumatic diagrams ❏ - Wiring diagrams ❏ - Certificate of analysis of the airborne noise emitted by the machinery

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

3

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Information/Introduction

1

1.1 Warranty The factory guarantees that the machinery described in this handbook was tested to check its running performance and its safety while it was being manufactured.

- Products are covered by a 12 months’ warranty; electrical motors and electrical parts, however, are excluded from the warranty..

The warranty also excludes damage occurring if the machine falls during its installation or resulting from its misuse, from the non-compliance with the maintenance standards as well as from wrong operation performed by the machine operator.

The warranty will become void if the product or notably safety devices are tampered with; in this case, the manufacturer shall not be deemed liable for any injury to persons tampering with this equipment.

- No compensation shall be due for the machinery inactivity.

The serial number, which is affixed onto the machinery, is an essential reference for the warranty, the instruction handbook, the after sale service and the product identification for any need.

1.2 General test and inspection The machinery is tested at our factory to make sure the electrical system and all the moving parts are working correctly.

1.3 Warnings - Our machinery is manufactured in compliance with the accident prevention regulations in force in the manufacturing Country.

- In order to achieve an efficient performance level customers are hereby recommended to strictly follow the directions contained in this handbook.

In this way you will be able to achieve the top output of the machine and will avoid any problems which might stem from the failure to comply with the instructions pertaining to the machinery use and maintenance.

Please read carefully through the text and make sure you have fully understood all that is contained in this manual before proceeding to any starting, application, maintenance or other operation on the machinery.

- In order to avoid turning to the Manufacturer for minor troubles which can be easily eliminated, please follow the instructions given here below.

- Should you need to contact our Service Department, even after carefully following our instructions, it is essential for you to give us sufficient technical indication to enable us to identify the possible kind of failure and/or to define the malfunctioning parts.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

4

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Information/Introduction

1

This specific information will allow for a quicker and more efficient action on the machinery.

- Duplicate copies of this instruction handbook can be obtained by quoting the “serial number” of the machinery.

Maintenance on the machinery must be compulsorily carried out by authorized staff, only.

NOTE: "RIGHT" and "LEFT" indications refer to the operator positioned as defined in the herewith enclosed "Operatorís Work Station" lay-out.

1.4 Description The feeding device is a machine to be attached to vertical band saws in order to obtain the steady feed of the material to be cut. The feed is obtained thanks to a power-driven roller which, due to the contact, drives and transmits the motion to the workpiece to be cut up. A roller fence with appropriate length is essential to define the size of the cut up workpiece, ensure the workpiece stability while it is being cut and allow to apply the force for the feed.

The drive system comprises a motor coupled with a continuous speed variator, which is keyed directly to the reduction unit that is in turn mated with the drive roller.

All the machine is enclosed in a robust safety casing made of sheet steel, which also features a baffle board as a hand guard for the handling lever.

Model supplied with spring The contact force exerted between the feeding device and the workpiece is given by the load of a spring located lengthwise in relation to the feeding device.

The feeding device is engaged to and disengaged from the workpiece by the operator. He acts on a lever which is integral with the head of the feeding device itself.

A pivot to lock in place ensures the permanent stop in the disengaged positioning.

Pneumatic model The contact force exerted between the feeding device and the workpiece depends on the action of a double acting pneumatic cylinder located lengthwise in relation to the feeding device.

The feeding device is engaged to and released from the workpiece by means of the double acting cylinder.

For all the models the feeding roller can be either of rubber or of toothed steel.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

5

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Information/Introduction

1.5

1

Uses of the machinery for its intended purposes

The machinery was designed and constructed to be applied onto the work table of the stationary-table vertical band saws.

This machinery must be fitted by pre-setting the work table as described in the chapter relating to the installation contained in this manual and by making use of the fitting material the machinery comes supplied with.

The machinery is apt to feed workpieces of a wooden material featuring at least two parallel, opposed surfaces: the roller fence and the feeding roller will refer on them.

The people involved in its design stage considered its use in a working environment with the specifications of temperature, moisture and lighting provided for by the Decree Law No. 626/1994 Title II.

1.6

Uses falling outside the intended purposes

Its use with materials other than wood or its by-products is not envisaged.

You also fall outside its intended purposes when you use a non-homogeneous material which does not feature two parallel, opposed faces the roller fence and the feeding roller can refer on

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

6

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Information/Introduction

1.7 Technical specifications Voltage Frequency Installed capacity Working pressure Overall dimensions Weight

Volt 220÷240~ 3 phases Hz - 50/60 kW - 0.5 bar - 5÷7 (pneumatic type) mm L. 910 x P. 350 x H. 300 Kg -

Feeding roller height Feeding roller diameter Max. roller-blade distance Max. fence-blade distance

mm - 130 mm - 215 mm - 150 mm - 200

Material feed speed (Mt/1'):

minimum 1,6 maximum 16

Noise level: *

1

dBA Leq - 70.5 ± 2 *

-Measuring conditions: machinery running at its most efficient working rate

Indications on the airborne noise emitted by the machinery The values quoted for the noise represent emission levels, but they do not necessarily represent levels for a safe working environment.

It is true that a correlation exists between emission levels and exposure levels, but we cannot rely upon it to determine whether or not further precautions are required.

The factors affecting the actual exposure level of the worker include the exposure duration, the environment characteristics, other sources of emission, such as the number of adjacent machines and other processings.

The allowed exposure levels as well may vary from one Country to another.

However, this information enables the user of the machinery to better assess the hazards and risks involved.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

7

Band saw feeding devices

SR-013

English

1

1.8 Storing conditions The machinery must be stored in a covered place, protected from weathering.

When packed, it can be kept stored in this place for one year at the temperature of -25 ÷ +55 °C. To store machinery after it was used over a given period of time, make sure to perfectly clean all its parts, protect it with anti-oxidising products and wrap it into a plastic film.

1.9 Machinery disposal In no case do the materials used for the machinery construction fall within the classification of the toxic, harmful products. Therefore you simply need to contact an authorised collection centre for the disposal of special waste.

Caution!!

The gear reducer contains oil.

1.10 Overall dimensions

▲

▼

▲

770

▲

1234567890 1234567890 1234567890 1234567890 1234567890 1234567890 1234567890 1234567890 1234567890 1234567890 1234567890

300

1234567890123456 1234567890123456 1234567890123456

180

▼

123456789012

140

▼

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

350

▲

▼

370

▲

▲

▼

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Information/Introduction

Page

8

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Machinery identifying data

2

Each machine is fitted with a rating plate (Fig.2.1) featuring the following data: -

Type of Machinery Serial No. Weight in Kg CE mark with year of construction of machinery Voltage in Volt Frequency in Hz Capacity in kW Energy requirements S.N.C. in Ampere Pressure in Bar MOD : Consumption Nl/1”

-

MATR :

NOTE: The data shown on the rating plate must NOT be altered for any reason whatsoever.

V~ :

Via Montale, 11 41030 Rovereto s/Secchia (Mo) - I Tel. ++39-59-673 003 Fax. ++39-59-673 007

Kg :

Hz :

kW :

bar :

Nl/1’ :

A:

Fig.2.1 An accurate and correct quotation of the Serial Number and of the Machinery Code will enable our Service Department to give quick and precise answers. The figure (Fig. 2.2) here below shows where the rating plate is located on the machinery.

S.N.C.

Via Montale, 11 41030 Rovereto s/Secchia (Mo) - I Tel. ++39-59-673 003 Fax. ++39-59-673 007

MOD :

MATR : V~ :

Kg :

Hz :

kW :

bar :

Nl/1’ :

A:

Fig.2.2

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

9

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Normal safety conditions -safety standards-

3

3.1 Introduction This section of the handbook deals with the recommendations and guidelines for the safe use of the SR-013 machinery.

These recommendations are about the installation, the operation and the maintenance and are repeated in the handbook according to the subjects concerned together with other specific warnings which are not included here below.

3.2

Definitions

Danger zone: any zone within and/or around machinery in which an exposed person is subject to a risk to his health or safety.

Exposed person: any person wholly or partially in a danger zone.

Operator: the operator must be a person trained on the machine operation. The operator performing the pre-setting and the maintenance of the machinery must be a person trained by SAM MECCANICA factory’s staff or by persons authorized by this factory.

On the first commissioning either SAM MECCANICA’s staff or its authorized representative shall train the purchasing Company both on the machinery use and maintenance and on how to use this handbook.

Hazard: Source of possible injuries or damage to health.

Risk: Combination of probability and of seriousness of possible injuries or damage to health in a hazardous situation.

Safeguards: safety measures consisting in the use of specific technical means referred to as safeguards (guards, safety devices) to protect persons against hazards which cannot be reasonably eliminated or sufficiently limited thanks to the design.

Guard: Element of a machinery used in a specific way to provide protection by means of a physical barrier.

Interlocking guard: Guard combined with an interlocking device ensuring that: -

the hazardous functions of the machinery “concerned” by the guard cannot be performed until the guard has been closed.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

10

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Normal safety conditions -safety standards-

3

if the guard is opened while the hazardous functions of the machinery are being performed a stop command is given the closure of the guard allows to carry out the hazardous functions of the machinery “concerned� by the guards, but there is no machinery starting command.

Safety device: device (other than a guard) eliminating or limiting the hazard, by itself or combined with a guard.

3.3 General safety standards Most of the occurring accidents are caused by the failure to observe some simple precautionary and safety rules.

Among these rules, one which is elementary and at the same time very important provides for the following: NEVER CARRY OUT ANY CLEANING, LUBRICATING OR MAINTENANCE OPERATION WHILE THE MACHINE IS WORKING. Please always bear in mind that the purpose of the safety devices the manufacturer has equipped the machinery with is only of providing a basic accident prevention.

The main responsibility for a manufacturing process without accidents falls on the owner of the machinery and on all the persons charged with its operation, its maintenance and its repair.

The owner of the machinery shall make sure that: - his/her personnel are trained on the job assigned to them and that they act in compliance with the safety standards; - safety standards are steadily complied with; - a notice showing the safety standards is affixed in the working area.

To this purpose, please read carefully through these safety standards and stick to them.

To draw up the following safety chapter not only did we take account of the regulations in force for the prevention against accidents on the job but also of: DPR (Italian Presidential Decree) No. 224 dated 24.5.88 Responsibility for damage resulting from a defective product.

Directive No. 98/37/EEC dated 22/6/98

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

11

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Normal safety conditions -safety standards-

3

Decree Law No.626 datedl 19th Sept., 1994 enforcing the Directives: Directive No. 89/391/EEC dated 12/6/89.

Implementation of measures aimed at promoting the improvement of health and safety standards for workers, while at work.

Directive No. 89/654/EEC dated 30/11/89 Relating to the minimum health and safety requirements for working environments.

Directive No. 89/655/EEC dated 30/11/89 Relating to the minimum health and safety requirements for the use of working equipment by workers while at work.

Directive No. 89/656/EEC dated 30/11/89 Relating to the minimum health and safety requirements for the use of personal protection equipment by workers while at work.

Caution !!!

For the correct use of this machinery, of its relevant electrical equipment, and in order to prevent electrical charges, injuries, risks of explosion and fire the following indications for safety must always be observed.

3.4

General indications

1. Keep an orderly workstation An untidy workstation involves the risk of accidents 2. Take account of the environmental conditions - Install the machine in a well-lit location - The floor must be clean and without any oil or grease stains.

3. Wear adequate clothing The operator’s clothing must be as appropriate as possible, which means that it must not be too loose-fitting and that it must feature no fluttering parts and no parts subject to entanglement hazards.

Sleeves must feature an elastic.

No belts, rings or chains must be worn.

Possibly make use of accident-prevention shoes Long hair must be held within a specially-designed hairnet.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

12

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Normal safety conditions -safety standards-

3

4. Avoid unstable positions Make sure you are steadily in a safe position with respect to the operating machinery and properly balanced.

5. Opening keys Give the keys of the machinery to the persons authorized to gain access to it. Do not leave within reach of the unauthorised personnel the keys with which you can open access doors to electrical, hydraulic, pneumatic sections or the keys of padlocking switches.

6. Remove the service keys from the machinery Before putting the machinery into service, make sure that all the keys and equipment used for adjustment and maintenance purposes have been removed.

7. Have repairs performed by trained personnel This machinery and its electrical equipment are achieved in compliance with the accident prevention regulations in force.

Repairs must be carried out solely by trained persons, by making use of original spare parts, otherwise damage to the machinery and to its user might arise.

Never start any cleaning or maintenance operation without having previously unplugged the machinery and unloaded the machinery pressure.

8. Unplug the machinery Before carrying out any action on the electrical equipment take the power-supply plug off the patchboard.

Should you notice phenomena of static electricity, check immediately the grounding of the machinery.

Make sure to connect the machine to a power-supply line equipped with a good earth point.

9. Avoid wrong use of the power-supply cable.

Make only use of cables featuring a cross-section fit for the installed capacity of the machinery.

10. Foreign matters.

Do not introduce foreign matters in the electrical motor covers and do not plug the machine in by tampering with the mains switch and with safety miscroswitches.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

13

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Normal safety conditions -safety standards-

3

11. Keep this instruction handbook in good condition.

12. Before the operation Each day, before operating the machine, make sure that all the safeguards, the covers and the casings are in place and firmly secured.

3.5

Specific indications

General inspection Before using the machinery, you must carefully check for its efficiency, for the perfect operation of the safety devices and for the presence of damaged parts, if any.

Make sure the moving parts work smoothly. They must not turn out to be locked.

Make also sure there are no damaged parts and that all the components are properly fitted and work correctly.

Safety devices or damaged parts must be repaired or replaced with great craftsmanship with one of our Service Departments or by our skilled personnel.

3-6 Safety equipment (see lay-out of safety devices) The machinery comes supplied with the following main guards and safety devices: a b c d

Sheet steel whole machinery casing Sheet steel baffle board, as a hand guard Interlocked door which can be opened to adjust the position of the drive roller Machinery locking system in its open position

Model supplied with spring: e Access door to adjust spring pressure Model supplied with control unit: f Padlocking mains switch Pneumatic model: g Safety solenoid valve controlling the opening of the feeding device during a power failure event or in an emergency event affecting the machine on which the feeding device is fitted.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

14

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Normal safety conditions -safety standards-

3

CAUTION!!!

THIS CHAPTER DEALING WITH THE SAFETY WAS DRAWN UP BY TAKING ACCOUNT OF THE STANDARD OPERATING CONDITIONS OF THE MACHINERY, DEFINED AND SPECIFIED IN THE CHAPTER DESCRIBING ITS USE, AS WELL AS

BY BASING ON THE ASSUMPTION THAT THE OPERATORS HAVE BEEN DULY TRAINED AND MADE AWARE OF THE SPECIFIC HAZARDS PRESENTED BY THE MACHINERY ITSELF. IF THE MACHINERY IS NOT USED IN THE CONDITIONS DESCRIBED IN THIS INSTRUCTION HANDBOOK, THE MANUFACTURER DISCLAIMS ALL RESPONSIBILITY FOR ANY DAMAGE TO PEOPLE OR TO FIXTURES AND FITTINGS WHICH MIGHT OCCUR. FURTHERMORE, THE MANUFACTURER DISCLAIMS ALL RESPONSIBILITY FOR DAMAGE TO PEOPLE OR TO FIXTURES AND FITTINGS BROUGHT ABOUT BY AN IMPROPER USE OF THE EQUIPMENT OR BY THE NONCOMPLIANCE WITH THE FOLLOWING RECOMMENDATIONS: take the required precautionary steps while performing such operations as adjustments, replacement of parts, cleaning, repairs or maintenance in order to prevent other people from starting the machinery; do not tamper with or replace the guards and the safety devices the machinery comes supplied with; Put back in place the guards and the safety devices as soon as the technical conditions or requirements justifying their temporary removal (subject to an explicit authorization by a person in charge) are over.

Use the machinery on the envisaged voltage and pressure and under the stress conditions compatible with the productive process and with its limits of use.

Always make use of protective gloves during both the machinery use and its maintenance.

-

Always make use of protective glasses while the machinery is being used.

Evaluate the need to make use either of noise-proof headsets or of other personal protection equipment, as provided for by TITLE IV of the Decree Law No. 626/ 1994.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

15

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Normal safety conditions -safety standards-

3.7

3

Explanation of symbols:

Graphical representation of the warning signs (triangular shape) and prohibition signs (round shape), which are generally used on SAM MECCANICA’s machinery and maintenance manuals.

NOTE: The meaning of symbols other than the represented ones will be given from time to time.

GENERAL HAZARD Indicates some important points for the operator’s personal safety. When this sign is exposed on any part of the machinery, this means: CAUTION! (SITUATION OF GENERAL HAZARD FOR THE SAFETY OF THE PERSON AND/OR OF THE MACHINERY).

BEWARE OF ELECTRICAL CHARGES!

CAUTION! PRESSURE

BEWARE OF HANGING LOADS!

BEWARE OF HOT SURFACES!

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

16

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Normal safety conditions -safety standards-

3

BEWARE OF FINGER CRUSHING!

DO NOT USE WATER TO PUT OUT FIRES

USE IS FORBIDDEN TO UNAUTHORIZED PEOPLE

DO NOT REMOVE GUARDS AND SAFETY DEVICES

DO NOT REPAIR, ADJUST, LUBRICATE OR CLEAN WHEN IN MOTION

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

17

Band saw feeding devices

SR-013

English

4

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Installation/Connections

4.1

Machinery lifting and handling

The machinery can be lifted and handled thanks to the special eye-bolt (A) and by means of an overhead travelling crane or hoist or other compatible lifting equipment.

Well-positioned ropes featuring appropriate bearing capacity should be used as slings.

CAUTION !!!

The staff in charge of machinery lifting and installation operations shall carry out the described operations with the utmost care and attention, so as to avoid damage to people or to fixtures and fittings.

☞

Before positioning the machinery make sure you have correctly prepared for use the work table of the band saw onto which it will be installed.

A

Fig.4.1

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

18

Band saw feeding devices

SR-013

English

4

4.2

Machinery positioning

Prepare the work table of the vertical band saw according to the directions of the diagrams illustrated here below. (Fig.4.2) If the machinery the feeding device is to be installed on is a model whose work table features smaller dimensions than the ones shown in the diagrams, the dimension of the work table must be increased by adding fence tailpieces. (Fig.4.3)

WARNING!!!

•

n.4 12MA

140

▼

➚

100

▼

180

▲

Should you fail to observe the right dimension of the work table, the feeding device may turn out to be projecting outside the edge of the work table itself when it is in its rest position. This entails a risk of shearing between the feeding device and the work table during the movement to engage with the workpiece or in the job-over position.

Fig.4.2

265

31

▼

336

▲

•

▼

▼

104

▲

▲

➘

▲

n.2 10MA

Back position Opened position

Fig.4.3 12 12

12 12

➹

1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123 1234567890123

➹

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Installation/Connections

Fence tailpices

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

19

Band saw feeding devices

SR-013

English

4

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Installation/Connections

Position the feeding device onto the band saw work table and fasten it by means of the supplied screws.

Position the roller fence and maintain it in place by tightening the supplied screws slightly.

By means of a rule align the roller fence with the blade, then fasten the clamping screws tightly.

Put an element of a known dimension between the blade and the roller fence, by taking care to lean without bending the blade and tighten the dimension-locking knob.

Position the millimetric rule into the special slit obtained on the roller fence and secure it in place by taking care of having the dimension relating to the size of the workpiece used as a reference coincide with the value read obtained on the roller fence body.

Fasten the millimetric rule tightly.

Pneumatic model Fit the pneumatic panel at the edge of the vertical band saw, within easy reach and far away from hazardous elements.

Model supplied with control unit Fit the control unit at the edge of the vertical band saw, within easy reach and far away from hazardous elements.

Place the control unit so that the mains switch handle comes to be located at an elevation between 0.6 and 1.9 metres from the ground.

CAUTION!!!

Take a special care in wiring the electric power supply and/or the pneumatic supply line, so as to avoid that they might either hinder the standard use or interfere with moving parts or tools.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

20

Band saw feeding devices

SR-013

English

4

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Installation/Connections

4.3

Electrical connection

Safety conditions: The machine on which the band saw feeding device will be installed must be in conformity with the health and safety regulations in force in the country of use; for the European Community, the machine must have the CE mark.

CAUTION !!!

ALL THE OPERATIONS FOR THE CONNECTION TO THE MAINS MUST BE MADE WHEN THE POWER SUPPLY LINE IS DEAD, BY SKILLED AND EXPLICITLY AUTHORIZED STAFF AND ALWAYS IN THE FULL COMPLIANCE OF THE REGULATIONS IN FORCE. Make sure that the frequency and power supply voltage values (see rating plate) are the same as the values of the mains.

CAUTION !!!

In all patchboards the connection of the ground wire (GND - PE - Y) is of vital importance. It must feature an appropriate cross-section to protect the operator against accidental contacts between metallic parts of the machinery and live wires or components.

The cables used to supply current must feature a sufficient cross-section and insulation must be fit for the voltage and temperature requirements relating to the machinery.

For this assessment, please read the max. required power among the general data of the machinery.

To avoid the fire hazard, just make use of the exact kind of fuses, with a correct voltage and tension.

IT IS STRICTLY FORBIDDEN TO MAKE OPERATIONS ON LIVE ELECTRICAL EQUIPMENT. -

DEROGATIONS, IF ANY, MUST BE AUTHORIZED BY THE HEAD IN CHARGE.

-

UNDER CONDITIONS OF A PARTICULAR DANGER, ANOTHER PERSON MUST BE PRESENT TO ASSIST THE WORKER DOING THE JOB.

START JOBS ONLY WHEN ALL THE SAFETY MEASURES HAVE BEEN IMPLEMENTED.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

21

Band saw feeding devices

SR-013

English

4

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Installation/Connections

☞

Connection: First make sure that the voltage shown on the rating plate fixed on the machine exactly matches the mains voltage, then connect the feeding device to the electrical system of the band saw by means of a cable of appropriate dimensions and protected by a reinforced-type flexible sheath.

In order to safeguard the motor, the saw electrical system must be supplied with an overcurrent protection device (thermal sensor) complying with the technical provisions governing accidental startings and the electrocution protection.

Ascertain whether the short-circuit current intensity envisaged at the connecting terminals of the mains switch is compatible with its cut-off power.

Hook up the contacts of the safety electrical interlock switch relating to the door allowing to gain access to the internal parts so as to cut out the power supply to the feeding device when the access door is open and so as to avoid its automatic restart as soon as the access door is closed (Short-circuit in compliance with CEI 44-5 standards).

☞

Ensure that the band saw feeding device cannot be started if the machine on which it is installed is off. Therefore, turn the mains switch of the band saw to "0-OFF" and check that the power to the band saw feeding device is also cut.

CAUTION!!!

THE MANUFACTURER DISCLAIMS ALL RESPONSIBILITY FOR ANY ACCIDENT OR INCONVENIENCE OCCURRED WHEN THE ABOVE-DESCRIBED CONNECTIONS ARE OMITTED OR WRONGLY PERFORMED. Feeding device supplied with electrical equipment Fit a plug featuring electrical specifications apt for the machinery energy requirements and connect it to a power supply line equipped with an equipotential protection device and with protection fuses of appropriate size.

To verify the correct connection of the machine, take the following steps: -

Supply the machine with driving voltage by means of the MAINS SWITCH Make sure that the MUSHROOM-HEAD EMERGENCY button of the band saw is not pressed.

Operate the feeding device by activating the control you have used (if the connections is directly, starting when the band saw machine will start) and check whether the drive roller is spinning in the right direction. On the contrary, invert two of the phases of the electrical connection.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

22

Band saw feeding devices

SR-013

English

4

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Installation/Connections

Pneumatic feeding device The feeding device with pneumatic opening/closing comes supplied with a safety solenoid valve: In the event of a power failure or of an emergency, the latter opens the feeding device or disengages it from the workpiece, unless there is a failure in the compressed air supply.

Connect the power supply of the safety solenoid valve by withdrawing power from a power supply source inside the band saw control unit. This source must provide for the power supply cut-out as a result of a stop or of an emergency command.

See the wiring diagram of the pneumatic feeding device for the power supply specifications of the safety solenoid valve.

See the wiring diagram of the band saw to select the exact connection location for the power supply of the solenoid valve itself.

CAUTION!!!

Make some functional tests before using the machinery.

Position the opening command lever so that it might be easily controlled, either directly or by means of the workpiece to be machined. You must avoid approaching dangerous areas such as the blade or taking unstable or twisted positions.

This lever is usually fitted on one side of the roller fence, at the material entry section, so that the workpiece might operate it directly, while it is being inserted.

4.4

Pneumatic connection

Connect the compressed air supply line with the entry section of the FilterRegulator Lubricator (FR+L) assembly by means of a quick coupling for 1/2" tubes.

The supply line must be fitted with an ON-OFF valve so that the machinery might be insulated from the supply line in the event of maintenance work or operations on the feeding device which are not directly related to its standard use.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

23

Band saw feeding devices

SR-013

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

IN ORDER TO ASSURE A GOOD VISIBILITY OF THE DESCRIBED PARTS SOME ILLUSTRATIONS OR DRAWINGS ARE REPRESENTED WITHOUT THE GUARDS THE MACHINERY COMES SUPPLIED WITH. MAKE SURE THAT THESE ONES ARE ALWAYS FEATURED AND IN PLACE BEFORE YOU USE THE MACHINERY.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

24

Band saw feeding devices

SR-013

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

5.1

Controls and regulators

1- Control LEVER to bring the feeding device to its working position or to release it from such a position.

2- PIVOT locking the feeding device in its open position 3- SPEED ADJUSTING HANDWHEEL 4- NUT to adjust the spring tension

Pneumatic model 56789-

BRAKING REGULATORS SPEED REGULATORS REGULATORS OF THE SUPPLY LINE PRESSURE LEVER for feeding device opening command OPENING TIME REGULATOR

Model supplied with electrical equipment 10-MAINS SWITCH

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

25

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Band saw feeding devices

4

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

SR-013

English

Use

5

2

3

1

Page

26

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Band saw feeding devices

7

8

10

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

SR-013

English

Use

5

6

9

5

1

0

Page

27

SR-013

Band saw feeding devices

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

5.2

Pre-setting of the standard machine

Feeding roller opening By means of the hexagonal nut (a) adjust the distance between the roller and the blade to obtain a minimum distance of 10 mm and a maximum one of 150 mm.

a 1234 1234 1234 1234

a

1234 1234 1234 1234

1234 1234 1234

123 123 123 123

1234 1234 1234

1234 1234 1234 1234

1234 1234 1234

1234 1234 1234 1234

1234 1234 1234

1234 1234 1234 1234

123 123 123

1234 1234 1234

Fig.5.2

Pressure of the feeding roller on the material By means of the hexagonal nut (b) increase or decrease the force with which the feeding device tightens the workpiece.

1234 1234 1234 1234

1234 1234 1234 1234

1234 1234 1234

123 123 123 123

1234 1234 1234

1234 1234 1234 1234

1234 1234 1234

1234 1234 1234 1234

1234 1234 1234

1234 1234 1234 1234

123 123 123

1234 1234 1234

b

Fig.5.3

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

28

Band saw feeding devices

SR-013

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

p

Feed speed adjustment Rotate the knob of the speed variator (p) to select the most appropriate feed speed.

THE ADJUSTMENT MUST BE CARRIED OUT WHEN THE FEEDING ROLLER IS IN MOTION SO AS TO AVOID POSSIBLE DAMAGE TO THE SPEED VARIATOR.

Fig.5.4 5.3

Pre-setting of the pneumatic model

Feeding roller opening Unscrew the clamping nut (a).

By means of a fork spanner put into the special slots obtained on the rod (b) itself, increase the distance between feeding roller and blade by screwing the rod of the stationary support (c). Take the opposite steps to approach them.

Tighten the clamping nut (a).

a 1234567890 1234567890 1234567890 1234567890 1234567890 1234567890 1234567890

c

b

Fig.5.5

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

29

Band saw feeding devices

SR-013

English

5

Use

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

a

Pressure of the feeding roller on the material Turn the pressure regulator (a) to increase or decrease the working pressure on the material (max. 6 bar).

Fig.5.6

Moving speed adjustment Turn the flow regulators (b) and (c) by means of a screwdriver b- adjusts the speed at which the workpiece is approached c- adjusts the release speed

c

b

Fig.5.7

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

30

Band saw feeding devices

SR-013

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

Adjustment of opening/ closing end of stroke damper Turn the regulator (a) located on the cylinder by means of a screwdriver. This is aimed at increasing or decreasing the effect of the opening end of stroke damper. Turn the regulator (b) for the closing end of stroke.

The damper must produce such an effect as not to kick back on the cylinder hinge-pivots.

b

a

Fig.5.8

Opening time adjustment Turn on the knurled pawl (c) of the adjusting valve (d) to increase or increase the opening time of the feeding device.

The opening time is to be adjusted as a function of the time required to correctly position the workpiece to be cut up.

d

c

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Fig.5.9

Page

31

Band saw feeding devices

SR-013

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

5.4

c

Use

Cutting dimension adjustment Slacken the knob (a) and rotate knob (b) to decrease or increase the distance between the roller fence (c) and the blade (min. 3 mm max.: 200 mm).

The value read on the millimetric rule referring to the back section of the support will indicate the cutting dimension.

b

Lock the knob (a)

Fig.5.10

a

CAUTION!!!

THE OPERATIONS DESCRIBED FROM NOW ONWARDS MUST BE PERFORMED WHEN THE TOOL OF THE BAND SAW IS RUNNING AT STANDARD WORKING SPEED.

Feeding device starting Make sure the feeding device is locked in its open position and put the material to be cut up between the feeding device and the roller fence.

Turn the main switch to 1 (ON), if this is the device which you have used to start the feeding device.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

1

0

Fig.5.11

Page

32

Band saw feeding devices

SR-013

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

Cutting starting Catch hold of the handling lever (a) with your left hand and with your right hand release the feeding device by lifting the knob (b).

Accompany the motion of the feeding device until the feeding roller and the material to be b cut up are engaged.

Fig.5.12

a

Feeding device stop Once the cutting is over, catch hold of the handling lever and bring the feeding device to its fully-open position where it will make a permanent stop thanks to the automatic locking system in the open position.

Bring the main switch of the motor to its 0 (OFF) position to stop the rotation of the feeding roller.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

1

0

Fig.5.13

Page

33

Band saw feeding devices

SR-013

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

5.5

Use of the pneumatic feeding device

1

Feeding device starting Turn the main switch to 1 (ON), if this is the device which you have used to start the feeding device.

0

Fig.5.14

Cutting starting Press the switch (a) and put in the material to be cut up until the feeding device reaches its open position.

Once the pre-set opening time is over, the feeding device closes and starts feeding the material.

a

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Fig.5.15

Page

34

Band saw feeding devices

SR-013

English

5

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Use

Feeding device stop 1

Bring the main switch of the motor to its 0 (OFF) position to stop the rotation of the feeding roller.

If the stop is for an end of shift of job, disconnect the pneumatic supply as well.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

0

Fig.5.16

Page

35

Band saw feeding devices

SR-013

English

6

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Trouble-shooting guide and possible remedies

Problems

Causes

Remedies

Standard feeding device There is a tendency for an Insufficient pressure of the - Increase the feeding roller pressure feeding roller irregular material feed - Select a lower speed; verify the saw Excessive feed speed wear

Pneumatic feeding device The feeding device does not Insufficient supply line - Make sure the compressed air supply line pressure falls within the requested open to allow the material pressure values insertion Opening command out of - Make sure the lever for the opening command acts correctly on the order pneumatic switch - Verify there are no mechanical hindrances such as chips, etc..

The feeding device does not No power supply to the safety - Supply line failure - Emergency of the sawing machine close in its working position solenoid valve Excessive opening time

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

- Reduce the pre-set opening time

Page

36

Band saw feeding devices

SR-013

English

7

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Maintenance

7.1 Safety conditions (safety standards) For the safety conditions and standards to be followed in the various maintenance steps stick to the directions contained on chapter 3. Standard safety conditions.

7.2 -

7.3 -

-

-

7.4 -

Daily maintenance By using a brush and a vacuum cleaner clean the roller feeding the material and the rollers of the roller fence.

Clean and lubricate the rack over which the roller fence moves.

Grease the rotation pivot of the supporting arm of the feeding device by using a pump with a delivering unit which is appropriate for the applied valve.

Make sure the handling lever is securely fastened.

Weekly maintenance Check the oil level in the gear reducer through the inspection window applied on the gear reducer itself. If required, top it up through the opening closed with cap placed on top of the gear reducer.

Recommended oil type: GX 80 W 90.

Verify the transmission belt wear Check the level of the oil contained in the speed variator by means of the inspection window fitted on the variator. If required, top it up.

Pneumatic model Verify the level of the lubricating oil contained in the FR + L assembly and top it up if required.

Check for the presence of condensate accumulated in the tank of the FR+ L assembly. If required, drain it Make sure that the positions of minimum and maximum opening and that the positioning speeds are maintained unaltered.

Monthly maintenance Check the tightening of all the screws of the bearing unit of the feeding device arm and the clamping of the sawing machine onto the work table, clean the internal parts.

NOTE: Do not use compressed air jets to make these cleaning operations.

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

37

Band saw feeding devices

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

English

SR-013

12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121

12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121

SPARE PARTS 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121 12345678901234567890123456789012123456789012345678901234567890121

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

38

Band saw feeding devices

SR-013

English

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

CONVENIENT GUIDE FOR THE RESEARCH OF A DETAIL ON THE CATALOGUE

First locate the detail you want to request on the spare parts tables by means of the number distinguishing it. Thanks to this number, you can trace the code, the description and the quantity of the detail in question by looking up the relevant list.

RULES TO BE OBSERVED WHEN ORDERING SPARE PARTS

ORDERING EXAMPLE

013RR001 - 1 - 01.SR-013.00 - Qt. 1 a

b

c

d

a - Code number of the detail b - Position number of the detail on the table c - Table number d - Quantity (it can differ from the one shown on the list)

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

39

Via Montale, 11 -41030 Rovereto s/Secchia -Modena - Italy

RECOMMENDED Machinery type SPARE PARTS Band saw feeding devices

SR-013

SR-013

English Code

1

013RR001

SUPPORTING ARM WITH REST

1

2 3 4 5 6 7 8 9 10 11 12

013RR002 013RR003 013RR004 013RR005 013RR006 013RR007 013RR008 013RR009 013RR010 013RR011 013RR012

BEARING WORM SCREW SPLINE O-RING CROWN GEAR SPACER SPLINE SLOW SHAFT SPLINE BEARING O-RING

1 1 1 1 1 1 1 1 1 1 1

13

013RR013

OIL FILLER CAP

1

14

013RR014

GEARMOTOR

1

15 16

013RR015 013RR016

TOOTHED ROLLER RUBBERISED ROLLER

1 1

17

013RR017

COMPLETE SPRING ASSEMBLY

1

18 19

013RR018 013RR019

COMPLETE PNEUMATIC CYLINDER COMPLETE PNEUMATIC SYSTEM

1 1

20

013RR020

INTERLOCK MICROSWITCH

1

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Det.

Description

SAMMeccanica MeccanicaS.N.C. S.N.C. - ROVERETO s/SECCHIA (Modena) Italy SAM - ROVERETO s/SECCHIA (Modena) Italy

Q.ty

Page

40

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Band saw feeding devices

1 2 3

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

SR-013

English RECOMMENDED SP ARE PPARTS ARTS SPARE

4

w

x

y

z

1

SHEET 01-SR-013-00 Page 41

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Band saw feeding devices

1 2

15 3

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

SR-013

English RECOMMENDED SP ARE PPARTS ARTS SPARE

4

w

x

y

z

16

SHEET 02-SR-013-00 Page 42

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Band saw feeding devices

20 1 2 3

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

SR-013

English RECOMMENDED SP ARE PPARTS ARTS SPARE

17 4

w

x

y

z

18

SHEET 03-SR-013-00 Page 43

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Band saw feeding devices

1 2 3

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

SR-013

English RECOMMENDED SP ARE PPARTS ARTS SPARE

4

w

x

y

z

19

SHEET 04-SR-013-00 Page 44

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Band saw feeding devices

13

1

x 2 3

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

SR-013

English RECOMMENDED SP ARE PPARTS ARTS SPARE

6-7-8-9-10-11-12 4

w

❉ ❉

y

z

2-3-4-5

SHEET 05-SR-013-00 Page 45

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

Band saw feeding devices

1 2 3

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

SR-013

English RECOMMENDED SP ARE PPARTS ARTS SPARE

14 4

w

x

y

z

SHEET 06-SR-013-00 Page 46

Band saw feeding devices

SR-013

Document with all rights reserved, according to the law. No part of this instruction handbook may be reproduced or made available to any third party, in any form or by any means, without prior explicit permission.

English

BAND SAW FEEDING DEVICES Via Montale, 11 - 41030 Rovereto s/Secchia - Modena - Italy Tel. 059-673003 - Fax. 059-673007

SAM Meccanica S.N.C. - ROVERETO s/SECCHIA (Modena) Italy

Page

47