+PLA20X42-3%3ALathe+20+42+sheet+1+to+end+rev+1

20x42

Dear Woodworker:

Thank you for your purchase and welcome to the Laguna Tools group of discriminating woodworkers. I understand that you have a choice of where to purchase your machines and appreciate the confidence you have in our products.

Every machine sold by Laguna Tools has been carefully designed and well thought through from a woodworker’s perspective. I cut on our bandsaws, lathes, table saws and combination machines. Through my hands-on experience, I work hard to make our machines better.

I strive to give you machines that inspire you to create works of art.

Machines that are a joy to run and work on. Machines that encourage your performance.

Today, we offer high-performance machines with innovative solutions that meet the needs of woodworkers and their everevolving craft.

I started Laguna Tools as a woodworker, I still am.

Thank you again for becoming a Laguna Tools customer.

Torben Helshoj President and Founder - Laguna Tools Imagination, Innovation and Invention at work.

2

Table of contents Page number Safety Rules

4

Warranty

5

Noise emission

6

Specification sheet

6

Receiving your machine

6

Introduction to your machine

7

Parts of the machine

7

Where to locate your machine

11

Unpacking your machine

12

Assembly and setup

13

Maintenance and troubleshooting

20

Exploded view drawings

23

Electrical drawing

24

3

Safety Rules.

As with all machinery there are certain hazards involved with the operation and use. Using it with caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. If you have any questions relative to the installation and operation, do not use the equipment until you have contacted your supplying distributor.

Read the following carefully before operating the machine.

1. Keep the working area clean and be sure adequate lighting is available.

2. Do not wear loose clothing, gloves, bracelets, necklaces or ornaments. Wear face, eye, respiratory and body protection devices as indicated for the operation or the environment.

3. Be sure that the power is disconnected from the machine before tools are serviced or an attachment is to be fitted or removed.

4. Never leave the machine with the power on.

5. Do not use dull, gummy or cracked cutting tools.

6. Be sure that the keys and adjusting wrenches have been removed and all the nuts and bolts are secured.

4

LIMITED WARRANTY New woodworking machines sold by Laguna Tools carry a one-year warranty effective from the date of shipping. Laguna Tools guarantees all new machine sold to be free of manufacturers’ defective workmanship, parts and materials. We will repair or replace, without charge, any parts determined by Laguna Tools, Inc. to be a manufacturer’s defect. We require that the defective item/part be returned to Laguna Tools with the complaint. In the event the item/part is determined to be damaged due to lack of maintenance, cleaning or misuse/abuse, the customer will be responsible for the cost to replace the item/part, plus all related shipping charges. This limited warranty does not apply to natural disasters, acts of terrorism, normal wear and tear, product failure due to lack of maintenance or cleaning, damage caused by accident, neglect, lack of or inadequate dust collection, misuse/abuse or damage caused where repair or alterations have been made or attempted by others.

Laguna Tools, Inc. is not responsible for additional tools or modifications sold or performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc. woodworking machine. Warranty maybe voided upon the addition of such described tools and/or modifications, determined on a case-by-case basis.

Normal user alignment, adjustment, tuning and machine settings are not covered by this warranty. It is the responsibility of the user to understand basic woodworking machinery settings and procedures and to properly maintain the equipment in accordance with the standards provided by the manufacturer.

Parts, under warranty, are shipped at Laguna Tools, Inc.’s cost either by common carrier, FEDEX ground service or a similar method. Technical support to install replacement parts is primarily provided by phone, fax, e-mail or Laguna Tools Customer Support Website. The labor required to install replacement parts is the responsibility of the user.

Laguna Tools is not responsible for damage or loss caused by a freight company or other circumstances not in our control. All claims for loss or damaged goods must be notified to Laguna Tools within twenty-four hours of delivery. Please contact our Customer Service Department for more information.

Only new machines sold to the original owner are covered by this warranty. For warranty repair information, call 1-800-332-4094.

Copyright 2010 Laguna Tools, Inc ** Warning – no portion of these materials may be reproduced without written approval from Laguna Tools, Inc.

5

Noise emission.

Notes concerning noise emission : Given that there exists a relationship between noise level and exposure times, it is not precise enough to determine the need for supplementary precautions. The factors affecting the true level of exposure to operators are clearly the amount of time exposed, the characteristics of the working environment, such as other sources of dust and noise, etc. for example, adjacent machines - in other words, the level of ambient noise. It is possible that exposure level limits will vary from country to country.

Specification sheet.

Motor Voltage Swing over bed Distance between centers RPM range Spindle Tail stock Tool rest Face plate Weight Length/Width/Height..

3 HP 220V Three phase 20 inches [508mm] 43 inches [1092mm] 0 to 3000 RMP 1-1/4 in. x 8 TPI RH MT number 2 Cast iron MT number 2 13 inch Yes 578 lbs.

103 x 25 x 49-1/2 in

Receiving your machine Note. It is probable that your machine will be delivered by a third party. Before you unpack your new machine you will need to first inspect the packing, invoice and shipping documents supplied by the driver.

Insure that there is no visible damage to the packing or the machine. You need to do this prior to the driver leaving. All damage must be noted on the delivery documents and signed by you and the delivery driver. You must then contact the seller [Laguna Tools] as soon as practical. If damage is found after delivery, contact the seller as soon as is practical.

Note. It is probable that you will find sawdust within your machine. This is because the machine has been tested prior to shipment from the factory and or Laguna Tools.

Laguna Tools endeavors to test machines prior to shipping to customers as movement can take place during transportation. It must be noted that additional machine movement can take place between Laguna Tools and the end user and some adjustments may have to be undertaken by the customer. These adjustments are covered in the various sections of this manual.

6

Introduction to Lathes.

This machine is designed to give you years of safe service. Read this owners manual in its entirety before assembly or use.

Parts of the Lathe The lathe consists of a number of major parts, which are discussed in this manual. Take the time to read this section and become familiar with the machine.

Identification.

There is a plate at the back of the machine listing all the manufacturing data, including the serial number, model, etc.

Out board leg

Lathe cabinet

Lathe legs.

The Leg is a heavy pressed steel construction that gives the machine a low centre of gravity, and ensures that it is very stable. The lathe cabinet supports the other end of the bed. There is a metal tray that joins the two parts that is used to store tools and equipment being used on the lathe.

7

Head stock Head stock The head stock is cast iron and houses the variable speed control and motor.

The head stock has an indexing pin that allows it to be locked in 15 degree increments.

Tail stock Tail stock.

The tail stock is a cast iron construction. It can accommodate centers and other tools which have a number 2 Morse taper. The tail stock can be moved to any position on the lathe bed and locked to suit the job in hand.

8

Bed tool rest

Outboard tool rest

Tool rest There are two tool rests. One that is located on the bed of the lathe and the second tool rest that is located at the left hand of the lathe. The left hand tool rest is used for bowl turning and is adjustable both vertically and also laterally to suite the job in hand.

Door switch Motor electronics

Motor

9

Speed sensor

Electrical cable

Electrical system.

The electrical control system is housed inside the left hand leg and accessed by opening the door located at the front of the lathe. There is a speed sensor that is located inside the pulley housing and is accessed by lifting the pulley cover. A power cord is provided. The power cord [located at the back of the lathe] is not provided with a plug as this will depend on your insterlation.

Lathe bed viewed from the under side Bed of the lathe.

The bed of the lathe is a heavy cast iron construction and is ribbed for extra rigidity.

10

Tool tray Tool tray.

There is a large tool tray located under the bed of the lathe that is convenient for storing tools and equipment that is used on the lathe.

What you will receive with the Lathe.

Tools Knock out rod

Running centre

Drive centre

Face plate

Where to locate your machine.

Before you remove your machine from the packaging, select the area where you will use your machine. There are no hard and fast rules for its location, but below are a few guidelines: 1. There should be an area at the front of the machine suitable for comfortable working.

2. There should be sufficient area at the back of the machine to allow access for adjustments and maintenance to be conducted.

3. Adequate lighting. The better the lighting the more accurately and safely you will be able to work.

4. Solid floor. You should select a solid flat floor, preferably concrete or something similar.

5. Locate it close to a power source and dust collection.

6. Allow an area for the storage of blanks, finished products and tools.

11

Unpacking your machine.

To unpack your lathe you will need a screwdriver, tin snips and a wench.

1. Using the tin snips, cut the banding that is securing the packing box [If fitted].

WARNING: EXTREME CAUTION MUST BE USED, BECAUSE THE BANDING WILL SPRING AND COULD CAUSE INJURY. 2. Dismantle the box, including the sides as this will ease access to the machine.

Mounting bolts 3. Remove the base mounting bolts that secure the machine to the base of the box.

4. It is recommended that the lathe be removed from the packaging by lifting it with a hoist or forklift using a "SLING". Remove the packaging and lower to the floor. Insert the slings only under the bed of the lathe and as far apart as possible. Do not lift the lathe by slinging under the tool tray.

Note. The machine is heavy. Ensure that you have sufficient people.

Note. If you have any doubt about the described procedure, seek professional assistance. Do not attempt any procedure that you feel is unsafe, or that you do not have the physical capability of achieving.

12

Assembly and setup The machine comes mostly assembled. You will have to assemble the tool rest to the bed of the machine.

Mounting the late to the floor

Floor mounting bracket Two floor mounting brackets are provided to attach the lathe to the floor [optional]. Floor mounting hardware is not provided. The mounting brackets will accept 3/8� fixings. If you decide to mount the lathe to the floor you may have to shim the lathe to ensure that the bed is level in both directions.

Assembling the tool rest the bed of the machine.

Tool rest Tool rest clamp nut Lathe bed tool rest.

Remove the clamping nut and washer.

Fit the tool rest onto the bed of the lathe. Refit the washer and nut.

Adjust the nut until the clamping handle secures the tool rest to the bed of the lathe.

The tool rest can be moved to any position on the bed of the lathe, and also inout to suit the job in hand. To move the tool rest, loosen the locking handle, move to the required position and lock.

13

Positioning Inboard Tool Rest on lathe bed.

Loosen the tool rest holder lock lever and move the tool rest assembly to the desired position. Once in the desired position lock the lever to secure the tool rest assembly in position.

Note: The tool rest holder lock has an adjusting nut that may need adjustment with time.

Adjusting Tool Rest Height.

Loosen the tool rest lock handle and adjust the angle or height of the tool rest.

Position the tool rest approximately 1â „4" away from the work piece and Approximately 1â „8" above the work piece center line.

Re-tighten the tool rest lock handle to secure the tool rest in position.

Turning jobs larger than 20" in diameter, mount the work piece on the outboard side of the lathe and use the outboard tool rest.

To use the outboard tool rest.

Holding the tool rest support rod firmly, loosen the lock levers and move the tool rest to the required position.

Re tighten all lock levers before starting the operation.

Connecting the electrical supply.

Ensure that the electrical supply corresponds with that of the machine [Single phase 110V].

It is recommended that you use a 15-amp main breaker. Amp draw under full load 9 Amps

Note. A qualified electrician must carry out the installation.

Cleaning the machine.

Remove the rust protection grease with WD 40 or a similar solvent.

It is important that you remove all the grease and re lubricate with a Teflon-based lubricant. Teflon has fewer tendencies to attract sawdust, and cause clogging.

On flat surfaces it is recommended that the grease is scraped off the machine with a plastic scraper [do not use a metal scraper, as this could damage the machine surfaces].This will save time and reduce that amount of solvent that is required to clean the lathe.

14

Knock out rod fits through hole in the back of the handle

Knock out rod

Rotating centre Fitting the rotating centre.

Ensure that the bore of the tail stock is clean. The rotating centre has a number No 2 Morse taper that fits into the tail stock.

Push the centre into the tail stock bore firmly, and ensure that it is securely located. To remove the centre, push the knock out shaft through the hole in the back of the tail stock and give it a sharp knock. This will remove the rotating centre. Ensure that the centre does not drop. It is suggested that you hold your hand under the centre to catch it as it is hit with the knock out rod.

Note. Do not leave the removal shaft in the tail stock with the machine running.

Fitting the drive centre in the head stock.

Ensure that the bore of the head stock is clean. The drive centre has a number No 2 Morse taper that fits into the head stock.

Push the centre into the head stock bore firmly, and ensure that it is securely located. To remove the centre, push the removal shaft into the back of the head stock, and give it a sharp knock. This will remove the drive centre. Ensure that the centre does not drop. It is suggested that you hold your hand under the centre to catch it as it is hit with the knock out rod.

Note. Do not leave the removal shaft in the head stock with the machine running.

15

Spindle lock engaged Spindle lock disengaged Fitting the face plate and or removing the hand wheel.

Lock the spindle in position. The face plate screws onto the spindle and is locked in position with the Allen screws. Remove the spindle lock before you start the lathe. To removal the face plate, lock the spindle, loosen the Allen screws, and rotate the face plate. Remember to remove the spindle lock before you start the lathe The faceplate can also be mounted on the outboard side of the lathe for turning work pieces larger than 20" in diameter. In this case, the hand wheel is mounted on the inboard side of the lathe.

On button

Speed control button

Speed display

Stop button Forward / reverse switch Head stock controls and adjusting the spindle speeds.

On switch powers the system and starts the spindle rotating to the speed set by the variable speed control knob. It is suggested that the variable speed control knob is set to the approximate speed prior to starting the spindle rotation and then once the spindle is rotating fine tune the spindle speed.

With the drive belt on the low range the spindle speed is from 10 to 1000 rpm.

With the drive belt on the mid range the spindle speed is from 1000 to 2000 rpm.

With the drive belt in the high range the spindle speed is from 2000 to 3000 rpm.

Red off switch removes power from the system.

16

Once the red off switch has been pushed, it has to be twisted, and pulled out to reset the power. If the lathe will not start, check that the red stop switch is in the fully out position.

Note: Always disconnect the machine from the power when conducting maintenance or adjustments to the lathe, [changing the belts on the pulleys, etc].

Forward / reverse switch changes the direction of the spindle. Never change the position of the switch while the spindle is rotating. If the spindle rotation is changed while the spindle is turning the electronics and or the motor will be damaged. The forward / reverse switch must not to be used as a quick stop for the lathe spindle.

Test run.

Now that the assembly is complete and you have a good understanding of the lathe controls, it is time to conduct a test run to check that all the functions of the lathe are working correctly.

Check that the spindle lock is disengaged.

Check that all tools etc have been removed from the lathe.

Make sure that you have read and understood the manual.

Press the red stop button and then twist anti clockwise so that it pops out.

Turn the speed dial to zero [off position].

Check that the cabinet door is fully closed.

Connect the power to the lathe.

The test will check that the motor works correctly, all the controls function correctly and that the safety switches function correctly.

If any of the tests fail, the lathe must not be used until the fault has been corrected.

Press the on button and using the speed dial increase the speed of the spindle slowly. The lathe should run smoothly with little or no vibration.

Reduce the speed using the speed control dial until it is in the off position.

Turn the speed control dial until full speed is achieved and then press the red stop button.

The lathe should stop.

Press the start button. The lathe should not start. This is a safety feature and must function correctly. If it fails to function the lathe must not be used until the fault has been corrected.

Turn the speed dial to the off position and reset the stop button by turning anti clock wise until it pops out.

Press the start button and turn the speed dial until the spindle is turning. Open the cabinet door a small amount until the door safety switch functions.

With the door slightly open the spindle should have the power removed and the spindle should stop turning.

This is a safety feature and must function correctly. If it fails to function the lathe must not be used until the fault has been corrected.

17

Upper pulleys

Ratchet clamp handle Adjustment lever

Changing the drive belt to different pulley sets.

Remove the power from the lathe.

The motor and pulleys are accessed through the cabinet door.

Loosen the ratchet clamp handle and move the adjustment lever to remove the tension on the drive belt. Re clamp the ratchet clamp lever.

Move the drive belt to the required set of pulleys.

Loosen the ratchet clamp handle, re apply tension to the drive belt with the adjustment lever and re clamp the ratchet clamp handle.

The tension should be about 1/8� movement of the belt when pressed with moderate thumb pressure.

Before reconnecting the power to the lathe, ensure that the upper pulley cover is closed and locked in position.

There is a micro switch that acts on the lower door and removes power from the lathe. [Never rely on the switch and disconnect the lathe from the power prior to changing the drive belts to a different set of pulleys]. If the door is not fully closed the lathe will not start. Prior to starting the lathe, check that the door is fully closed.

18

Spindle lock

Tail stock position lock

Tail stock The tail stock can be moved to any position on the bed of the lathe. To move the tail stock, unlock the tail stock position locking handle, slide the tail stock to the required position and lock. The tail stock spindle can be extended and retracted by rotating the handle located at the back of the tail stock. The spindle can be locked in position with the locking handle on top of the tail stock. Always lock the spindle when operating the lathe.

Viewing hole

Spindle lock disengaged

Spindle lock engaged

Spindle lock / indexing.

The spindle lock engages in any one of 24 holes. This allows for the spindle to be locked in 15 degree. Never start the lathe with the spindle lock engaged as this will strain the motor and the lathe electronics.

Each spindle lock hole has its own number that is viewed through the viewing hole on the out board side of the head stock.

19

Maintenance General.

Keep your machine clean. At the end of each day, clean the machine. Wood contains moisture, and if sawdust or wood chips are not removed they will cause rust.

In general, we recommend that you only use a Teflon based lubricant on the lathe. Regular oil attracts dust and dirt. Teflon lubricant tends to dry and has fewer tendencies to accumulate dirt and saw dust.

Periodically check that all nuts and bolts are tight.

Drive belt The drive belt should last for many years [depending on the usage] but need to be inspected regularly for cracks, cuts and general wear. If damage is found, replace the belt.

Bearings.

All bearings are sealed for life and do not require any maintenance. If a bearing becomes faulty, replace it.

Rust The lathe is made from steel and cast iron. All none painted surfaces will rust if not protected. It is recommended that they are protected by applying wax or a Teflon based lubricant General.

Each week the motor should be cleaned of any accumliated saw dust as this will reduce the motor cooling. Also check that the cabinet cooling slots are clean and free from a build up of sawdust and dirt.

Check all nuts and bolts are tight and that there is no dammaged parts

Troubleshooting.

Symptom Lathe will not start.

Possible cause Check that the stop switch is in out positon.

Check that the electrical power cord is plugged into the power outlet.

Check that the electrical supply is on.

With the power disconnected

Possible sloution Reset stop switch.

Plug in the lathe to the power.

Reset the breaker.

Rewire plug.

20

from the machine, check the wiring to the plug is correct.

The machine will not stop.

Check that the rubber insulation is stripped enough and is not causing a bad connection.

Check that all the screws are tight.

Start switch faulty.

Spindle direction switch faulty.

Inverter faulty.

This is a very rare occurrence as the machine is designed to fail-safe. If it should occur and you cannot fix the fault, seek professional assistance. The machine must be disconnected from the power and never run until the fault has been rectified.

Stop switch faulty.

Motor tries to start but will With the power disconnected not turn. from the machine. Try to turn the spindle by hand. If the spindle will not turn, check the reason for the jamming.

Capacitor faulty.

Motor overheats.

Strip back wiring.

Tighten screws.

Replace switch.

Replace switch.

Replaceinverter.

Replace the stop switch.

Remove cause of jamming.

Replace the capacitor.

Replace the motor.

Motor faulty.

The motor is designed to run hot, but should it overheat it has an internal thermal overload protector that will shut it down until the motor has cooled, and then it will reset automatically.

If the motor overheats, wait until it has cooled and restart.

If the motor shuts down Typical reasons consistently check for the are dull cutting reason. tools, motor cooling fan clogged or faulty, motor cooling fins clogged, over feeding the job, and excessive

21

Squeaking noise.

Spindle slows down during a cut. .

Check that the motor cooling fan is not contacting the fan cover.

Check the bearings.

Check the drive belt.

Dull cutting tools.

Feeding the wood too fast.

Oil or dirt on the drive belt.

Machine not level on the floor.

Machine vibrates.

Damaged drive belt.

Job is not balanced.

Damaged pulley.

Motor loose.

Lathe not mounted on the floor correctly and is not sitting on four corner points.

Bearing faulty.

Motor mounting loose or broken.

Loose or dammaged cover.

Loose pulley.

Job mounted incorrectly.

Spindle speed too fast for job.

Tail stock moves.

Dull or incorrect tools being used.

Tail stcck clamp is not adjusted correctly.

Bed is greassy.

ambient temperature.

Adjust mootor cooling fan.

Replace bearings.

Retension or replace drive belt.

Replace the tool or have it resharpened.

Slow down the feed rate.

Clean or replace the drive belt.

Re-level the machine ensuring that it has no movement.

Replace the belt.

Change to slower speed and or balance the job Replace the pulley.

Tighten motor.

Mount lathe correctly.

Replace bearings.

Tighten motor and or replace broken part.

Tighten and or replace cover.

Tighten pulley.

Remount job.

Slow the lathe down to correct speed.

Use correct /sharp tools.

Adjust tail stock clamping nut.

Clean bed.

22

Electrical drawing

23

24

Part No

DESCRIPTION

PART No

DESCRIPTION

1

BED

66

SPACING COLLAR

3

HEX BOLT 7/16-14 X 1-1/2

67

TRANSFORMER

5

LOCK WASHER 12MM

68

SPACER

10

LOCK WASHER 5/16

69

FIBER WASHER 12MM

18

HEAD STOCK

70

FLAT HD SCR 5-40 X 1

19

HEX BOLT 5/16-18 X 1-1/4

71

FLAT HD SCR 5-40 X 3/4

20

BELT WHEEL COVER

72

TACH SENSOR BAKS DA-1805NO

21

PHLP HD SCR 10-24 X 5/16

73

PHLP HD SCR M3-.5 X 20

26

PULLEY 3-STEP J9 SHEAVES

75

UPPER COVER

27

SET SCREW M8-1.25 X 40

76

HINGE ASSEMBLY W/O SCREWS

28

PHLP HD SCR M6-1 X 16

78

FLAT HD SCR 10-24 X 5/16

29

TAPERED BEARING LM67048/10

79

FLAT HD SCR 10-24 X 1/4

30

LOCK COLLAR

80

FLAT WASHER 5/16

31

SPINDLE ADAPTER

81

FLAT HD SCR 10-24 X 5/8

32

SHAFT JOINT

82

HEX NUT 5-40

33

SET SCREW 1/4-20 X 1/4

86

HEX NUT 10-24

34

SPINDLE HANDWHEEL

89

RIBBED V-BELT 580J9

35

SPINDLE

102

FACEPLATE LABEL

36

FACE PLATE 1-1/4 X 8 TPI

103

KEY 8 X 7 X 50

37

LOCK SET

105

KEY 5 X 5 X 18

39

SPUR CENTER

115

ADJUST HANDLE M12-1.75 X 20

40

TAILSTOCK BASE

121

CTRL PANEL CORD 8 WIRE 18AWG

41

TAILSTOCK LEADSCREW

122

TACH SENSOR BRACKET

42

SHORT HANDLE

123

TACH SENSOR CORD 3W 24AWG

43

CAM SPINDLE

124

SWITCH BOX

44

TAILSTOCK QUILL

124A

COMPLETE SWITCH BOX ASSY

45

LIVE CENTER SHAFT

125

LT STRAIN RELIEF PG11

46

BALL BEARING 6002ZZ

126

LT STRAIN RELIEF PG13.5

47

LIVE CENTER HEAD

127

RING SHAFT

47A

LIVE CENTER ASSY

128

EXT RETAINING RING 19MM

48

TAILSTOCK LOCK SHAFT

130

SET SCREW 5/16-18 X 5/16

49

CONTROL PANEL FACEPLATE

138

PUSH ROD 8 X 600MM

52

LOCK NUT M12-1.75

139

T-WRENCH 4MM X 100L

53

FLAT WASHER 1/2

140

T-WRENCH 3MM X 100L

54

SLIDE PLATE

141

THUMB SCREW 1/4-20 X 5/8

55

HANDWHEEL

142

GO BUTTON (GREEN)

56

HANDWHEEL HANDLE

143

STOP BUTTON (RED)

57

TOOL REST BASE

144

SPEED DIAL

58

TOOL REST

145

FWD/REV KNOB

59

TUBE

146

FWD/REV PLATE

61

DIGITAL DISPLAY CORD 2W 18AWG

147

COPPER SLUG 5 X 8MM

62

TOOL REST LOCK SHAFT

148

LOCK SHAFT EXTENSION

65

ACRYLIC BOARD

149

SET SCREW M5-.8 X 5

25

26

Part No

DESCRIPTION

PART No

DESCRIPTION

2

LEFT STAND (CABINET)

94

CAP SCREW M8-1.25 X 15

5

LOCK WASHER 12MM

95

CAP SCREW M8-1.25 X 25

6

LOCK WASHER 12MM

96

LOCK WASHER 3/8

8

HEX BOLT 7/16-14 X 1-1/4

97

9

L-BRACKET

98

FLAT WASHER 3/8 INVERTER PWR CORD 2W 14AWG

10

LOCK WASHER 5/16

104

11

DOOR

106

12

STAND ACCESS HANDLE

107

KEY 8 X 7 X 90 OUTBOARD MOUNTING BRACKET OUTBOARD ARBOR SHAFT

13

RUBBER FOOT

108

LOWER BRACKET

14

HEX BOLT 5/16-18 X 5/8

109

UPPER BRACKET

15

PARTITION BOARD

110

ARBOR SHAFT TUBE

17

RIGHT STAND

111

22

MOTOR

112

23

MOTOR PULLEY

113

24

SET SCREW M8-1.25 X 8

114

25

SET SCREW M8-1.25 X 30

115

50

CAP SCREW 10-24 X 1/2

116

OUTBOARD LONG SHAFT OUTBOARD SHORT SHAFT ADJUST HANDLE M10-1.5 X 20 ADJUST HANDLE M12-1.5 X 60 ADJUST HANDLE M12-1.75 X 20 ADJUST HANDLE M12-1.75 X 25

58

TOOL REST

117

HEX BOLT M8-1.25 X 30

60

118

FLAT WASHER 8MM

64

L-BRACKET LIMIT SWITCH CORD 2W 18AWG

119

LOCK NUT M8-1.25

77

HEX NUT 5/16-18

120

SET SCREW M8-1.25 X 10

80

125

LT STRAIN RELIEF PG11

126

LT STRAIN RELIEF PG13.5

84

FLAT WASHER 5/16 RESISTOR EACIN 300W 100 OHMS INVERTER DELTA VFD-E 022E21A

129

85

PHLP HD SCR 10-24 X 3/4

131

RUBBER HANDLE COVER LMT SWITCH SHINOZAKI AZD-1004

86

132

LIMIT SWITCH BRACKET

133

88

HEX NUT 10-24 POWER CORD 3 WIRE 14AWG MOTOR CORD 4 WIRE 14AWG

134

PHLP HD SCR M4-.7 X 35 TERMINAL 3-POST (W/COVER)

90

MOTOR BRACKET

135

PHLP HD SCR 10-24 X 1

91

MOTOR MOUNT PLATE

136

FLAT WASHER #10

92

BELT TENSION HANDLE FLAT HD CAP SCR M81.25 X 20

137

LOCK WASHER #10

83

87

93

27

28