7301I Series Operators & Parts Manual

SERIES 73011 SIDE DISCHARGE MOWER MODEL KR7321 • 10.8kW (14.5HP) 805mm (32") MODEL KR7322 -12.3kW (16.5HP) 805mm (32") MODEL KR7323 • 12.3kW (16.5HP) 1005mm (40") MODEL KR7320 -13.4kW (18HP) 1005mm (40••) REAR DISCHARGE MOWER MODEL KR7324 -12.3kW (16.5HP) 1005mm (40••) MODEL KR7319 • 13.4kW (18HP) 1005mm (40••)

RIDE-ON LAWN MOWER OWNER I OPERATORS MANUAL PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS SAFETY, OPERATING AND SERVICE INSTRUCTIONS IN THIS MANUAL ARE STRICTLY FOLLOWED NOTE: In order to assist your Servicing Dealer please bring this Manual if Service &/or Warranty work is required.

Revised 14/12/2006

OWNERS INFORMATION MACHINE SERIES NO: 7301I

SERIAL NO: _ _ _ _ _ _ __

Located on label inside console MODEL NO: KR._ _ _ _ _ __

ENGINE MODEL NO: _ _ _ _ _ _ _TYPE: _ _ _ _ _ __ CODE: _ _ _ _ __ DATE OF PURCHASE: _ _ _ _ _ _ _ _ _ _ _ _ __

ISSUED TO: OWNERS NAME:_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ ADDRESS: _ _ _ _ _ _ _ _ _ _ _ _ __ __

_

_

TOWN/CITY: _ _ _ _ _ _ _ _ _ _ _ _ _ _.STATE: _ __

ISSUED BY: AUTHORISED COX DEALER/DISTRIBUTOR: ADDRESS: _ _ _ _ _ __

_ _ _ _ _ _ _ _ ___

TOWN/CITY: _ _ _ _ _ _ _ _ _ _ _ _ _STATE: _ __

PRE DELIVERY CHECK LIST Check parts

18/10/2007

D

Assemble

D

Service

D

Instruction

D Page 2

~)sAFETY INSTRUCTIONS 1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

Read, understand and follow all instructions in the 23. Never mow while barefoot or wearing open sandals Owner/Operators manual. or thongs. Wear long trousers and heavy shoes.

Know the controls and how to stop the engine 24. It is advisable to wear suitable protective safety gear quickly in an emergency. when operating a mower.

Allow only responsible adults who are familiar with 25. Mow only in daylight or good artificial light. the instructions in this manual, to operate the rna- 26. Before using, always visually inspect to see that chine. blades, bolts and cutter assembly are not worn or Clear the area to be mowed of loose objects such as sticks, stones, bones, wire, toys, debris etc., which could be picked up and thrown by the blades.

DO NOT mow whilst people, especially children, or pets are in the mowing area.

DO NOT mow in any direction on slopes beyond 15 degrees {lin 3.75)(27%) Exerdse extreme caution on slopes.

Reduce speed on slopes and in sharp turns to prevent overturning or loss of control.

Start or stop slowly when on slopes.

Mow up and down slopes, not across the slope.

Stay alert for holes or bumps in the terrain and other hidden hazards.

Use care when pulling loads- use only approved hitch point; limit loads to those you can safely control; do not turn sharply; use care when backing up.

Maximum weight on tow hitch (9kg) Maximum tow weight (Trailer & Load) 90kg DO NOT use ground-engaging attachments. Dozer Blade, plough etc.

Watch out for traffic when crossing or operating the mower near roadways.

Stop the blades rotating before crossing surfaces other than grass.

When mowing, never direct discharge of material toward bystanders or allow anyone near the rnachine while it is in operation.

Before leaving the operators position- disengage all clutches and secure cutting units; return hydro drive pedal to neutral position, then set the parking brake; stop the engine and remove the key.

Disengage drive to attachments and stop engine before refueling; before removing grass-catcher; before clearing blockages from chute; before checking, cleaning or working on the mower; after striking a foreign object, check the mower for damage and make repairs before restarting and operating the equipment; if machine starts to vibrate abnormally check immediately.

Disengage drive to attachments when transporting or not in use.

A mower operator should be in good physical and mental health and not under the influence of alcohol or any drug which might impair vision, co-ordination or judgment.

18/10/2007

damaged. Replace worn or damaged blades and bolts in sets to preserve balance.

27. Check all nuts, bolts and screws often, always be sure the mower is in safe operating condition.

28. Keep safety devices (guards and switches) in place and In working order.

29. Never use the mower unless the grass catcher or guards provided by the manufacturer, are in position.

30. Ensure any replacement parts used comply with the original manufacturer's recommendations and specifications.

31. Replace worn or faulty mufflers.

32. Keep machine free of grass, leaves, or other debris, excessive oil, grease, or spilt fuel. These can be a fire hazard.

33. Refuel outdoors only. Do not smoke while fuelling engine. Never remove the cap of the fuel tank or add petrol while the engine is running or the engine is hot. Use an approved fuel container, funnel or siphon hose (statiC/spark resistant). Remove fuel cap slowly to relieve any tank pressure. If fuel is spilled, do not attempt to start the engine but move machine away from the area of the spill and avoid creating any source of ignition until fuel vapors have dissipated.

34. Check for fuel leaks while refueling, before and while using the mower. If a fuel leak is found, do not start or run the engine until the fuel leak is fixed and spilt fuel is wiped away.

35. Do not operate engine in a confined space where exhaust fumes (carbon monoxide) can collect.

36. Do not over-speed the engine or alter governor settings. Excessive speed is dangerous and shortens mower life.

37. Stop the engine whenever you leave the mower, even for a moment.

38. Store the mower in a well-ventilated room away from naked flames such as may be found in hot water heaters.

39. Do not lend or sell the mower, without the owner/ operators Manual.

Page 3

PRE-DELIVERY INSTRUCTIONS INTRODUCTION

STEERING WHEEL ASSEMBLY lead on to the positive terminal with Assemble as per drawing. terminal cover first, and then the black battery lead on to the negative.

The purpose of this section of the 1 "manual is to ensure the dealer makes PRE-o:uvfR~ 2 the necessary installations, adjust~ ments and checks required, before ~ ---- ---.........._ ' the machine is operational. This bes~ ¡ gins upon receiving the crated mower ~ and Is finalised once the mower has been sold. This is the minimum amount of work required; however it should not be limited to the areas detailed in this procedure.

J-........._ ""-

RESPONSIBILITY It is the responsibility of the dealer to ensure that before a machine is delivered to a customer, it is in satisfactory operating condition.

PROCEDURE UNPACK LAWN MOWER check loose parts supplied against the following list: o Owner/Operators Manual o Engine Owners Manual o Steering Wheel Incl Cover o Plastic battery caps (6) o Battery connection screws (2) o Battery connection nuts (2) & washers (2) o Ignition key set o Seat Springs (2) o Spring Mount Cap (2) 0 3/4" X 5/16" Bolts (2) o 5/ 16" Spring washers (2)

o o

5/16" Washers (2) Spark Plug Spanner & Tommy Bar

ASSEMBLE TOOLS & EQUIPMENT REQUIRED: Socket set containing 1/2", 13mm & lOmm sockets & extension 75mm (3") or longer. Spanner lOmm & 1/2''.

Battery charger 12V, 4 or 8amp.

SEAT Fit seat springs and bolts etc. To adjust seat, loosen the two Tri Knob on the seat base mounting and adjust to the desired position and tighten Tri Knobs.

18/10/2007

ASSEMBLE REAR GRASS CATCHER a)

Place the front frame with the short tubes in each comer on a flat surface with the short tubes up.

Fit the bottom frame over the two short tubes of the front frame which lean inwards. Note: Make sure the two holes in the sides of the bottom frame also face inwards as the struts tit into these.

Ref Part No Description c) Fit the top tube bow frame over 1 Str Wheel Cover incl the outward leaning front frame Badge 2 SH0512F Set Screw 5/16" short tubes. Note: Holes in the 3 WS050216Spring Washer frame sides must face inwards.

4 W052003 Washer Then install the two struts. d) Assemble tilt-lever handle into tiltlever case and position handle through the hole in the top location bracket. Retain case to the SEAT SWITCH location bracket using m8x20 screws and nyloc nuts, do not Connect wiring harness to seat switch. tension. Retain bottom of guide tube to bottom bracket with HOURMETER m8x20 screws and nytoc nuts.

Tension top and bottom screws.

Connect the black negative wire to the terminal supplied at the back of e) Feed the bag over the assembled frame with the plain plastic base the hourmeter. to the plain tube bow (bottom of NOTE - The Hourmeter will continue the catcher). Fit handle hole seal. to operate if the ignition switch is Tum catcher over then dip the turned to the "on" position with the f) bag onto the frame. Using a engine not running. small soldering iron melt through the mesh at the four bolt holes in BATTERY the top of the frame to suit the a) Raise bonnet. Remove battery handle bolts. damp bolt and damp. g) Place the catcher cover over the assembled bag and frame, line up b) Remove battery from mower and place on level surface. bolt holes. Using the two M8x40 c) Remove the tape covering the screws & nyloc nuts tit one handle tiller holes on the battery. to the rear of the catcher with the d) Fill each cell of the battery to behandle holes facing down and tween the upper and lower levels handle leaning toward the rear. marked on the battery using h) Using the two M8x20 screws and 1.240-1.260 specific gravity elecnyloc nuts tit the other handle to trolyte battery add. the front of the catcher with the e) Using a 12V, 4 or 8amp battery handle holes facing forward. charger, charge the battery for a Tighten all four handle screws. period of 30 minutes. i) Use the cable ties in the top corAfter charging proceed as follows: ners if necessary to dose any gap Install the battery caps which may occur between the bag Allow battery to stand for 30 minutes. and frame.

Check acid levels in all battery cells j) Install catcher onto the machine (top up if necessary). and adjust the mounting brackets Replace battery, battery clamp and and mudguard side adjustment tighten bolt. Install the red battery brackets if required.

ELECTRIC'S

Page4

ASSEMBLE REAR GRASS CATCHER • Place the front frame with the short tubes in each corner on a flat surface with the short tubes up.

• Fit the bottom frame over the two short tubes of the front frame wh ich lean inwards. Note: Make sure the two holes in the sides of the bottom frame also face inwards -~=::::::::::::::-as the struts fit into these.

• Fit the top tube bow frame over the _ _ _.....__ _ _ ___._ _ outward leaning front frame short tubes. Note: Holes in the frame sides must face inwards.

Then install the two struts.

• Assemble tilt-lever handle into tiltlever case and position handle through the hole in the top location bracket.

Retain case to the location bracket using m8x20 screws and nyloc nuts, do .....1t.~~~:t: not tension. Retain bottom of guide tube to bottom bracket with m8x20 screws and nyloc nuts. Tension top and bottom screws.

• Feed the bag over the assembled frame with the plain plastic base to the plain tube bow (bottom of the catcher). Fit handle hole sea l.

• Turn catcher over then clip the bag onto the frame. Using a small soldering iron melt through the mesh at the four bolt holes in the top of the frame _.._........._ to suit the handle bolts.

• Place the catcher cover over the assembled bag and frame, line up bolt holes. Using the two M8x40 screws & nyloc nuts fit one handle to the rear of the catcher with the handle holes facing down and handle leaning toward the rear.

• Using the two M8x20 screws and nyloc nuts fit the other handle to the front of the catcher with the handle holes facing forward. Tighten all four handle screws.

• Use the cable ties in the top corners if necessary to close any gap which may occur between the bag and frame.

• Install catcher onto the machine and adjust the mounting brackets and mudguard • Note: the top of the catcher should make contact with the top lip of the mounting panel when the catcher is closed.

18/ 10/2007

Page 5

Note: the top should make FUEL TAP CUTTER ENGAGEcontact with the top lip of the Ensure the fuel tap (lower left front MENT SWITCH mounting panel when the f fu 1 ta k) ¡ t ed t 0 th e Sit on seat with cutter engaged . comer o e n IS um catcher IS closed. "on" posi~on before attempting to (switch raised), and park brake on start eng1ne. (Use unleaded fuel (locked), attempt to start engine us-

SERVICE TV RES

Before operation ensure that tyre pressures are equal.

The recommended pressure is: Front lOOkPa(lS P.S.I.). Rear l OOkPa(lS P.S.I.)

ENGINE OIL Before operation ensure that engine oil level is to the full mark on the dipstick. (Refer to Engine Owners Manual for correct oil classification to use).

only).

lng ignition switch.

Engine should not start.

TO CHECK OPERATION OF

SEAT SWITCH

SAFETY SWITCHES

Sit on seat, with park brake on (locked) and start engine, engage cutter, and lift weight from seat.

Engine should stop.

CLUTCH/BRAKE SWITCH

NOTE - Park Brake must be engaged & cutter disengaged to Sit on seat with cutter engagement keep engine running before liftswitch depressed (cutting blade dis- ing weight from seat. engaged) and park brake off (unlocked), attempt to start engine using ignition switch. Engine should not start.

OPERATING INSTRUCTIONS THE CONTROLS AND THEIR FUNCTIONS ARE AS FOLLOWS:-

Ignition switch- Used to start

(14.5HP)/12.3kW (16.SHP) B&S engine. Push throttle control lever fully forward into narrow slot to start cold engine. Pull throttle control lever out of narrow slot after engine has started. 13.4kW (18HP) B&S. Pull choke knob fully out to cold start then push choke knob all the way in after engine has started.

Headlight switch- Used to tum headlights on or off. With ignition switch in "on" (2nd) position, pull switch lever back to "on" position to turn headlights on. Push switch lever forward to "off'' position to turn headlights off.

Seat switch- Used to stop engine if operator is not on the seat & cutter engagement switch is engaged and or park brake knob is not in locked "on" position or clutch/brake pedal fu lly depressed.

and stop engine. Insert key, tum key all the way right to "start" (3rd) position to start engine. When key is released from "start'' (3rd) position it will return to "on" (2nd) position. Turn key all the way left to "off'' (1~ position to stop engine. Remove key from "off'' (1 ~ position to lock ignition switch.

Throttle control lever- Used to regulate engine speed and cutter speed. Push lever fully back for slow engine speed. 10.8kW (14.SHP)/12.3kW (16.5HP) B&S engine, push lever to front end of medium width slot for fast engine speed. 13.4kW (18HP) B&S , push lever to front end of narrow slot for fast engine speed.

Choke control- Used to start a cutter engagement switchco I d engine.

1 0 . 8 k W Used to start and stop mowing

18/ 10/2007

attachment. With engine running at medium/fast speed, pull the switch knob out from the console to "engage" position to start mowing attachment. Push knob fully in toward console to "disengage" position to stop mowing attachment.

Cutting height adjustment lever-Used to change the mowing attachment cutting height. To raise cutting height, pull up on lever, stop at desired cutting height. To lower cutting height, pull up on lever slightly while depressing lever button, once button depresses lower lever, stop at desired cutting height and release button.

Clutch/Brake Pedal- Used to disconnect drive to transmission and to stop machine travel before setting park brake. Push pedal down to apply brake. Remove foot from pedal to release brake.

Page 6

Pari< Brake Knob- Used to keep machine stationary. Fully depress the Clutch/ Brake pedal and raise and hold the park brake knob up while releasing brake pedal to "on" {lock). To return park brake knob to "off' (unlock) position, depress clutch/ brake pedal on park brake fully and knob will return to "off' (unlock) position.

Drive Pedal- Used to control an infinitely variable ground speed between zero and maximum in forward or reverse. Also to select neutral. With engine running and park brake re~eased push down on front of dnve pedal to travel forward, push down on back of drive pedal to ~vel in reverse.

When pressure 1s rei~~ from front or back of pedal1t w1ll return to neutral position.

Fuel .tap knob- U~ t~ shut off fuel hne whe~ machm~ IS transported or not m operation to prevent fuel. leakage. Turn ,ruel, tap knob to nght 1/4 turn to off position to shut fuel line. Turn fuel tap .~ob to left 1/4 ~urn to "on" pos1tion ~o ~pen fuel hne.

Transm1ss1on pu'!lp by-pass lever- Used to disengage the transmission to al~ow the mower to be pushed eas1ly. Located at the rear of the transmission and forward of the tow plate. Move lever to right for normal operation or move lever to the left for free wheel.

Oil pressure warning light13.4kW {18HP) B&S EngineUsed to indicate engine oil pressure. Ught comes on to indicate low engine oil pressure when the engine is running.

lows:-

position, park brake . locked a~d ~oo~ _off hy~ro pedal, Insert key In 1gnrt1on sw1tch, turn key all the way right to start (3rd) position, release key when engine has

SEAT ADJUSTMENT - To adjust seat, loosen the two Tri Knobs on the seat ba~e mountin.g and adjust ~0 hte desired position and re9 en.

STARTING ENGINE ELECTRIC STARTER·Cold engine: Check. engine oil level, check fuel level, open fuel tap. To start engine, place throttie control lever into choke position (l3.4kW {lBHP) pull choke fully out), ensure mowing attachment control is in the "off' position, park brake locked and foot off hydro pedal, insert key in ignition switch, turn key all the way right to start ()rd) position, release key when engine has started. Note: More than 15 seconds of continuous cranking can damage the starter motor. Short starting cycles give best starter motor life. Allow starter motor to cool for 2 minutes before attempting to restart engine. After engine starts gradually move throttle control lever, out of narrow slot (choke position) {l3 4kw {lBHP) _ push choke knob i~) to obtain desired engine speed.

Hot engine: To start engine, place throttle control slightly past The instruments & their slow position, ensure mowing atfunctions are as foltachment control is in the "off'

Hourmeter- Used to indicate the number of hours the engine has operated. Note:- if the ignition · h· · h " " 'ti d swltc IS m t e on posl on an the engine i.s not .running, the hourmeter Will continue to oper-

~~· 1

d' sti k- Used t0 . d'1 eve1 1p c In I cate oil level in engine when engine is not running. (Refer to engine owner's manual for instructions on checking engine oil level)

18/10/2007

STOPPING ENGINE When stopping engine, ensure mowing attachment control is in the off position, return throttle to slow position, lock park brake, turn ignition switch to the "off' {1st) position.

DRIVING TO TRAVEL MACHINE FORWARD OR REVERSE: With engine running set throttle control lever to obtain desired engine speed, 3/4 to full throttle for the best mowing finish and for engine and transmission cooling.

Release park brake, let the dutch/brake pedal all the way out, apply ~ownward p~essure on front of dnve pedal w1th foot to travel forward, or apply downward pr~sure on back of. drive pedal w1~ toes to travel m reverse. It 1s not necessary.to apply foot brake before chang1ng from forward to reverse or reverse to forward. The amount of pedal travel is used to control the ground ~~' small downward travel Will g1ve a slow groun? s~, full downward travel w1ll g1ve a fast ground speed.

NOTE Use slo~er ground speed for traveling up and down slopes or mowing heavy growth.

TO STOP MACHINE TRAVELA~ply . cl~tch/brake peda.l fully, th1s w1ll d1scon~~ the dnve belt to th~ tra~sm1ss1on before the brake IS activated.

TO EMPTY REAR GRASS CATCHER. .

Disengage cutter, p~ll up tilt lever handle located on nght hand corner of the catcher cover Push stal rted. Mbov~ thdro~ede con~ol lever forward and down . to tilt ever to o tam eslr engine ch & . ~ d speed cat er empty. Dnve 1orwar , Rewi~d starter:- l3. 4 kw lower catcher push tilt lever handie down until it stops. {18HP) Note: Perform battery/ electrical service if unable to electrically start engine.

Page 7

MAINTENANCE SCHEDULE BEFORE EACH USE Check engine oil level, adjust if required Check engine air cleaner foam pre-cleaner, service if require Check engine rotating screen/finger guard, clean if required Check operation of safety switches, service if required Check foot brake operation, adjust if required Check tyre pressures, adjust if required

Grease stub axles Lubricate steering ball joints Check for loose fasteners, tighten if required Check mowing attachment cutter blades, bolts, nuts, disc/s, housing, and guards for wear or damage, replace if required Lubricate as necessary

BEFORE STORAGE Change engine oil

- Clean machine

- Lubricate as necessary

EVERY 5 HOURS Check engine oil level, adjust if required Check engine air cleaner foam pre-cleaner, service if required*

Check engine rotating screen/finger guard, clean if required*

*Service more often under dusty conditions, or where air bome debris is present

1 MONTH OR 5 HOURS which ever occurs first Change engine oil Check tyre pressures, adjust if required Check engine air cleaner foam pre-cleaner, service if required Grease stub axles Check engine rotating screen/finger guard, clean if required Lubricate steering ball joints Check for loose fasteners, tighten if required Check mowing attachment cutter blades, bolts, nuts, disc/s, Check foot brake operation, adjust if required housing, and guards for damage, replace if required Check operation of safety switches, service if required

DATE

I

I

HOURS........ ... ............... DEALER .... ......................................... .

3 MONTHS OR 25 HOURS which ever occurs first Change engine oil if operating under heavy load or high ambient temperature Check engine air cleaner foam pre-cleaner, service if req * Check engine rotating screen/finger guard, clean if required * Check battery condition, service if required Check foot brake operation, adjust if required Check operation of safety switches and replace if required

Check tyre pressures, adjust if required Grease stub axles* Lubricate steering ball joints Check for loose fasteners, tighten if required Check mowing attachment cutter blades, bolts, nuts, disc/s, housing, and guards for wear or damage, replace if required

*Service more often under dusty conditions, or where air borne debris is present

DATE

I

18/10/2007

I

HOURS ........ .... .. ....... ..... DEALER............................................. .

Page 8

6 MONTHS OR SO HOURS which ever occurs first Change engine oil If fitted clean engine exhaust spark arrester Check engine air cleaner foam pre-cleaner , service if required * Check engine rotating screen/finger guard, clean if required "' Check foot brake operation and pads for wear, adjust or replace if required Check tyre pressures, adjust if required Check operation of safety switches, service if required Check belts for wear or damage, replace if required

Grease stub axles* Lubricate steering ball joints Check steering rack and pinion for wear, adjust if required Check mowing attachment electromagnetic clutch/ brake for operation, adjust air gap if required Check for loose fasteners, tighten if required Check battery condition, service if required Check mowing attachment cutter blades, bolts, nuts, dise/s, housing, and guards for wear or damage, replace if required

"'Service more often under dusty conditions, or where air bome debris is present DATE

I

I

HOURS ...... .. .................. D EALER ..... ...... .................................. .

9 MONTHS OR 75 HOURS which ever occurs fi rst Change engine oil if operating under heavy load or high ambient temperature Check engine air cleaner foam pre-cleaner, service if req * Check engine rotating screen/finger guard, clean if required * Check for loose fasteners, tighten if required Check foot brake operation, adjust if required Check operation of safety switches and replace if required

Check tyre pressures, adjust if required Grease stub axles * Lubricate steering ball joints Check battery condition, service if required Check mowing attachment cutter blades, bolts, nuts, disc/s, housing, and guards for wear or damage, replace if required

*Service more often under dusty conditions, or where air bome debris is present DATE

I

I

HOURS ...... ...... .............. D EALER ......... ...... ......... ... ...... ... ... ...... .

12 MONTHS OR 100 HOURS which ever occurs first If fitted replace engine oil filter.

Change engine oil.

Check engine spark plug, clean, adjust, or replace if required.

If fitted clean engine exhaust spark arrester.

Check engine air cleaner foam pre-cleaner, service if req *.

Replace engine air cleaner cartridge, service if required*.

Clean engine cooling system*.

Check foot brake operation and pads for wear, adjust or replace if req.

Replace in-line fuel filter.

Check tyre pressures, adjust if required.

Grease stub axles*.

Lubricate steering ball joints Check belts for wear or damage, replace if required.

Check operation of safety switches, service if required.

Check mowing attachment electromagnetic clutch/brake for operation, adjust air gap if required Check battery condition, service if required.

Check for loose fasteners, tighten if required Check steering rack and pinion for wear, adjust if required.

Check mowing attachment cutter blades, bolts, nuts, disc/s, housing, and guards for wear or damage, replace if required.

"'Service more often under dusty conditions, or where air bome debris is present DATE

I

I

HOURS ....... ... ...... ........ ... DE_ALER............................................. .

15 MONTHS OR 125 HOURS which ever occurs first Change engine oil if operating under heavy load or high ambient temperature.

Check engine air cleaner foam pre-cleaner, service if required*.

Check engine rotating screen/finger guard, clean if required * .

Check operation of safety switches and replace if required.

Check foot brake operation, adjust if required.

Grease stub axles * .

Lubricate steering ball joints Check tyre pressures, adjust if required.

Check for loose fasteners, tighten if required.

Check battery condition, service if required.

Check mowing attachment cutter blades, bolts, nuts, disc/s, housing, and guards for wear or damage, replace if required.

*Service more often under dusty conditions, or where air bome debris is present DATE

I

18/ 10/2007

I

HOUR.S .......... .... ........ .. .. DEALER ....... ...... ... ............................. .

Page 9

18 MONTHS OR 150 HOURS which ever occurs first Change engine oil.

If fitted clean engine exhaust spark arrestor.

Check engine air cleaner foam pre-cleaner, service if required *.

Check engine rotating screen/finger guard, clean if required *.

Check foot brake operation and lining for ware, adjust or replace if req.

Check operation of safety switches, service if required.

Check tyre pressures, adjust if required.

If fitted check mowing attachment brake pad for wear, replace if required.

Check battery condition, service if required.

Check for loose fasteners, tighten if required.

Check belts for wear or damage, replace if required.

Check steering rack and pinion for wear, adjust if required.

Grease stub axles*.

Lubricate steering ball joints Check mowing attachment cutter blades, bolts, nuts, diSC/ s, housing, and guards for wear or damage, replace if req

*Service more often under dusty conditions, or where air bome debris is present

DATE

I

I

HOURS .......................... DEALER ............... ...................... ........ .

21 MONTHS OR 175 HOURS which ever occurs first Change engine oil if operating under heavy load or high ambient temperature.

Check engine air cleaner foam pre-cleaner, service if required *.

Check engine rotating screen/finger guard, clean if required *.

Check foot brake operation, adjust if required.

Check operation of safety switches and replace if required.

Check tyre pressures, adjust if required.

Grease stub axles *.

Lubricate steering ball joints Check battery condition, service if required.

Check for loose fasteners, tighten if required.

Check mowing attachment cutter blades, bolts, nuts, diSC/ s, housing, and guards for wear or damage, replace if required

*Service more often under dusty conditions, or where air borne debris is present

DATE

I

I

HOURS .......................... DEALER ..............................................

24 MONTHS OR 200 HOURS which ever occurs first If fitted replace engine oil filter.

Change engine oil.

Check engine spark plug, clean, adjust, or replace if required.

If fitted clean engine exhaust spark arrestor.

Check engine air cleaner foam pre-cleaner, service if req *.

Check engine air cleaner cartridge, service if required.

Clean engine cooling system*.

Replace in-line fuel filter.

Check foot brake operation and pads for wear, adjust or replace if req.

Check operation of safety switches, service if required.

Check tyre pressures, adjust if required.

Grease stub axles * Lubricate steering ball joints Check steering rack and pinion for wear, adjust if required Check belts for wear or damage, replace if required.

Check mowing attachment electromagnetic clutch/brake for operation, adjust air gap if required Check battery condition, service if required Check for loose fasteners, tighten if required Check mowing attachment cutter blades, bolts, nuts, dise/s, housing , and guards for wear or damage, replace if required.

*Service more often under dusty conditions, or where air bome debris is present

DATE

I

I

HOURS ............... ........... DEALER ................................... ........ .. .

27 MONTHS OR 225 HOURS which ever occurs first Change engine oil if operating under heavy load or high ambient temperature.

Check engine air cleaner foam pre-cleaner, service if req *.

Check engine rotating screen/finger guard, clean if req *.

Check foot brake operation, adjust if required.

Check operation of safety switches and replace if req.

Check tyre pressures, adjust if required.

Grease stub axles*.

Lubricate steering ball joints Check battery condition, service if required.

Check for loose fasteners, tighten if required.

Check mowing attachment cutter blades, bolts, nuts, dise/s, housing, and guards for wear or damage, replace if req.

*Service more often under dusty conditions, or where air bome debris is present

DATE

I

18110/2007

I

HOURS ...... ......... ....... .... DEALER .................... ......................... .

Page 10

30 MONTHS OR 250 HOURS which ever occurs first Change engine oil.

If fitted clean engine exhaust spark arrestor.

Check engine air cleaner foam pre-cleaner, service if required*.

Check engine rotating screen/finger guard, clean if required *.

Check foot brake operation and pads for wear, adjust or replace if req.

Check operation of safety switches, service if required.

Check tyre pressures, adjust if required.

Grease stub axles *.

Lubricate steering ball joints Check steering rack and pinion wear, adjust if required.

Check mowing attachment cutter blades, bolts, nuts, diSC/s, housing, and guards for wear or damage, replace if required.

Check belts for wear or damage, replace if required Check battery condition, service if required.

Check for loose fasteners, tighten if required

*Service more often under dusty conditions, or where air borne debris is present

DATE

I

I

HOURS .... .. .... ... ...... ....... DEALER ................... .......................... .

33 MONTHS OR 275 HOURS which ever occurs first Change engine oil if operating under heavy load or high ambient temp.

Check engine air cleaner foam pre-cleaner, service if required* Check engine rotating screen/finger guard, clean if required * Check foot brake operation, adjust if required Check operation of safety switches and replace if required

Check tyre pressures, adjust if required Grease stub axles * Lubricate steering ball joints Check mowing attachment cutter blades, bolts, nuts, disc/ s, housing , and guards for wear or damage, replace if required Check battery condition, service if required Check for loose fasteners, tighten if required

*Service more often under dusty conditions, or where air borne debris is present

DATE

I

I

HOURS........ ......... ... ...... DEALER ..... .......................... .... ..... .. ....

36 MONTHS OR 300 HOURS w hich ever occurs first If fitted replace engine oil filter Change engine oil Check engine spark plug, clean, adjust, or replace if required If fitted clean engine exhaust spark arrestor Check engine air cleaner foam pre-cleaner, service if required* Check engine air cleaner cartridge, service if required Clean engine cooling system* Replace in-line fuel filter Check foot brake operation and lining for ware, adjust or replace if req Check operation of safety switches, service if required

Check tyre pressures, adjust if required Grease stub axles * Lubricate steering ball joints Check steering rack and pinion wear, adjust if required Check belts for wear or damage, replace if required If fitted check mowing attachment brake pad for wear, replace if required Check battery condition, service if required Check for loose fasteners, tighten if required Check mowing attachment cutter blades, bolts, nuts, diSC/ s, housing, and guards for wear or damage, replace if required

*Service more often under dusty conditions, or where air borne debris is present

DATE

I

18/10/2007

I

HOURS.................. ........ D EALER ......... ...... .... ...... .............. .... .. .

Page 11

MAINTENANCE INSTRUCTIONS Before servidng, disconnect spark. plug wire and ground it, disconnect battery at negative terminal, to prevent acddental starting. Reference to the left or right side of the machine is determined by sitting in the operating position.

I MPORTANT: If operating in conditions such as those mentioned below, engine oil, air filtering, chassis lubrication, greasing and adj ustments should be serviced at more frequent intervals than spedfied in this booklet a. Mowing in damp or wet conditions. b. Mowing in rough or dusty conditions. c. Mowing in hilly areas under heavy load.

Ensure machine has park brake engaged when attempting to start engine.

Never alter factory setting of maximum engine R.P.M. CHECK ENGINE Oil lEVEl- Refer to engine owners manual for correct method to check engine oil level.

CHANGE ENGINE Oil - Refer to engine owner's manual for correct method to change engine oil.

CHECK ENGINE AIR ClEANER FOAM PRE-ClEANER - Refer to engine owners manual for correct method to check and service engine air cleaner foam pre-deaner.

CHECK ENGINE ROTATING SCREEN/FINGER GUARD - Refer to engine owners manual for correct method to check and dean engine rotating screen /debris guard.

CHECK TYRE PRESSURES Adjust front and rear tyre pressure to 100kPa (15psi).

CHECK OPERATION OF SAFETY SWITCHES:PARK BRAKE SWITCH - Sit on seat with cutter disengaged (out), park brake disengaged, attempt to start engine. Engine should not

start.

DISENGAGEMENT SWITCH - Sit on seat with park brake engaged and cutter engaged, (in), attempt to start engine. Engine should not

start.

SEAT SWITCH Sit on seat and start engine, engage cutter, and lift weight from seat.

Engine should stop.

CHECK FOR lOOSE FASTENERS - TORQUEScnnNGS 5/ 16" UNC BOLT 5/16" UNF BOLT 3/8" UNC bolt/nut 3/8" UNF BOLT 7/16" UNF BOLT 6mm BOLT/ NUT Bmm BOLT/NUT lOmm NUT 12mm NUT 20mm NUT

20Nm (151bf tt) 23Nm (171bf tt) 36Nm (271bf tt) 41Nm (301bf tt) 68Nm (501bf tt) 9Nm (61bf tt) 15Nm (lllbftt) 44Nm (321bf tt) 53Nm (391bf tt) lOONm (741bf tt)

CHECK BATTERY CONDmON Raise bonnet, remove battery clamp and leads (negative lead first). Pull battery out. Remove battery caps and adj ust electrolyte levels between upper & lower level marks on battery case using distilled water.

Place battery in its recess. Refit leads (positive leads first) with terminal cover.

CHECK BRAKE OPERATION Apply Clutch/Brake pedal and set park brake, if mower can be pushed brake pad, brake spring, or brake linkage may need servicing.

GREASE STUB AXlES - Clean grease nipple, use grease gun and general-purpose grease to force old grease from top and bottom of front axle bushes. Jack up front of machine if grease is not released from bottom of bush.

CHECK CLUTCH OPERATION With pedal in up position check for 3-4mm play in the disengage rod slot and the disengagement arm pin (adjust by removing 'R' pin and washer) and turning in or out.

TO REMOVE 1005mm ( 40") MOWING ATTACHMENT (Rear Discharge) - With the engine off and spark plug lead removed . Lower mowing attachment fully. Discon-

18/10/2007

nect the two belt tensioning springs (top left side of mowing attachment). Remove cutter belt from engine pulley. Remove two 3/8" X 1 V2'' bolts, nuts & washers from support arms at the mowing attachment. Push up the right hand one onto the side of chassis. Remove the 3/8" x 1 1/4" bolt, nut, washer and spacer from right hand side front of the mowing attachment and the 'R' pin and washer. Remove mowing attachment pivot pin lock screw and nut (6mm) and remove mowing attachment pivot pin. Remove the two 'R' pins and washers from the lift link (at rear) and remove from the mowing attachment pins (note position of right hand Tilt machine to the left one). enough to clear the discharge shute of the mowing attachment from the shute in the machine and slide the attachment to the right.

Reassemble in reverse order.

TO REMOVE 805mm (32") MOWING ATTACHMENT - With the engine off and spark. plug lead removed, disconnect the belt tensioning spring (top left hand side of mowing attachment). Lower mowing attachment onto 20mm block front and rear. Remove cutter belt from engine pulley. Remove two 3/8" X 1 W' bolts, nuts & washers from support arms at the mowing attachment. Push up the right hand one onto the side of chassis. Remove 8mm x 2Smm bolt & nut from disengagement arm. Remove the 3/8" x 1 %" bolt, nut, washer and spacer from right hand side front of the mowing attachment and the 'R' pin and washer. Remove mowing attachment pivot pin lock screw and nut (6mm) and remove mowing attachment pivot pin. Remove the two 'R' pins and washers from the lift link (at rear) and remove from the mowing attachment pins (note position of right hand one). Turn the front wheels a little to the left and twist the mowing attachment to the right and slide the deck from under the mower.

Re-assemble in reverse order making sure the right hand left link is in the same hole as when removed.

To assist in refitting mowing attach-

Page 12

ment pivot pin, raise the mowing attachment slightly. Refit support arms with the washers In between the mowing attachment and the arm rod end. Refit cutter belt between belt guide, connect belt tensioning spring & refit spark plug lead.

TO REMOVE 1005mm ( 40") MOWING ATTACHMENT (Side Discharge) - With the engine off and spark plug removed. Lower mowing attachment fully. Disconnect the two belt tensioning springs (top left side of mowing attachment). Remove cutter belt from engine pulley. Remove two 3/8" X 1 V2" bolts, nuts & washers from support arms at the mowing attachment. Push up the right hand one onto the side of chassis. Remove the 3/8" x 1 1/4" bolt, nut, washer and spacer from right hand side front of the mowing attachment and the 'R' pin and washer. Remove mowing attachment pivot pin lock

screw and nut (6mm) and remove mowing attachment pivot pin. Remove the two 'R' pins and washers from the lift link (at rear) and remove from the mowing attachment pins (note position of right hand one). Tum the front wheels a little to the left and slide the deck to the right side from under the machine.

Re-assemble in reverse order making sure the right hand left link is in the same hole as when removed.

To assist in refitting mowing attachment pivot pin, raise the mowing attachment slightly. Refit support arms with the washers in between the mowing attachment and the ann rod end. Refit cutter belt between belt guide, connect cutter tensioning springs & refit spark plug lead.

REPLACE BLADES (swing back type & cutter bars) - Stop engine.

Remove spark plug lead. Check blades, blade bolts and nuts, if necessary simply remove the blade

bolt and nut using a suitable spanner and replace all blades, bolts and nuts. To preserve balance tighten blade nut to (36-40Nm). Do not over tighten.

CLEANING MACHI NE WITH WATER PRESSURE - Allow machine to cool down (min 2 hrs) before hosing down. Start engine and engage drive and cutting systems to clear water from pulleys and belts.

Stop engine and allow machine to dry. Lubricate as required. Do not cover machine with plastic or vinyl type material.

GENUINE SPARE PARTS - Always use Genuine Kingcat Spare Parts. Use of non-genuine Kingcat spare parts will void your warranty.

SAFETY FIRST - The use of mechanical devices can cause injury If incorrect procedures are used.

We are proud that you have purchased a Kingcat product and urge you to follow these instructions to obtain the maximum life for your machine. If in doubt check with your supplier.

18/10/2007

Page 13

Specifications !Model No.

Kingcat Ride-on Lawn Mower

73011

Product KR7319 13.4kW (18HP) Engine, HydrostaticTransaxle, 1005mm (40") Rear Discharge Mowing Attachment, 185 Litre Bag Grass Catcher.

Code

KR7320 13.4kW (18HP) Engine, Hydrostatic Transaxle, 1005mm (40") Side Discharge Mowing Attachment.

KR7321 10.8kW (14.5HP) Engine, Hydrostatic Transaxle, 805mm (32") Side Discharge Mowing Attachment.

KR7322 12.3kW (16.5HP) Engine, Hydrostatic Transaxle, 805mm (32") Side Discharge Mowing Attachment.

KR7323 12.3kW (16.5HP) Engine, Hydrostatic Transaxle, 1005mm (40") Side Discharge Mowing Attachment.

KR7324 12.3kW (16.5HP) Engine, Hydrostatic Transaxle, 1005mm (40") Rear Discharge Mowing Attachment, 185 Litre 8aq Grass Catcher.

Dimensions, Mass, Capacity

Length

Lawn Mower nc Grass Catcher Lawn Mower nc Mowing Attachment Discharge Deflector Up

~idth

KR7319

KR7320

KR7321

KR7322

KR7323

KR7324

1797mm 2197mm 830mm 1025mm

1766mm

1766mm

1766mm

1766mm

830mm 1195mm 1080mm

830mm 1020mm 880mm

lยง_30mm 1020mm ~Omm

830mm 1195mm 1080mm

1797mm 2197mm 830mm 1025mm

Height

1050mm

1050mm

1050mm

1050mm

1050mm

1050mm

~heel Base

1240mm

1240mm

1240mm

1240mm

1240mm

1240mm

660mm

~t>60mm

1060mm

660mm

~t>60mm

660mm

~t>33mm

~t>33mm

1033mm

633mm

633mm

633mm

193.2kg l16.41<g 12.4kg

181kg [45.8kg

1 82.5~

182.5~

182.5~

31.6kg

31.6~

l15.81sg

194.7kg l46.4kq 12.4kg

256.2kg*

226.8kg

214.1kg

~ 14.1kg

228.3kg

257.7kg*

7Utre 1.7 Utre

7Utre 1.7 Utre

7Utre 1.7 Utre

7Utre 1.7 Utre

7Utre 1.7 Utre

7Utre 1.7 Utre

Front Track 13x6.50-6 Tvresl Rear Track 18x8.50-6 Tvresl Dry Mass

Lawn Mower Mowinq Attachment !Grass Catcher rrotal * Inc deflector)

Fuel Tank Capacity Engine Oil Capacity Including Oil Filter Engine Design & Performance

Model Type:- Petrol, 4 Stroke/ AirCooled, Vertical PTO 25.4mm [1'1 Shaft/ Fuel Pump, Electric Start Cylinder Configuration Valve Type Displacement Bore x Stroke Maximum Rated Power Maximum Rated Torque Rated Engine Speed Maximum lrNo Load) die !Alternator Capacity (12 Volt DC) Dry Mass

18/10/2007

KR7319

KR7320

KR7321

KR7322

KR7323

KR7324

Briggs &

Briggs &

Briggs &

~tratton

~tratton

350777

Briggs & ::,tratton 350777

284H770

31E777

Briggs & ::,tratton 31E777

Briggs & Stratton 31E777

!Vanguard

Vanguard

Intek

Intek

Intek

~st Iron !Sleeve IV Twin !Overhead 570 cm3 72mm

Cast Iron ::,leeve V Twin Overhead 570 cm3 72mm

~st Iron ~leeve ~il}gle

~st Iron ~leeve

Cast Iron ::,leeve

~n_gle

~l}gle

!Overhead ~65 cm3

!Overhead 500 cm3

Overhead 500 cm3 j90.5mm

Cast Iron Sleeve Sinqle Overhead 500 cm3 90.5mm

lx

X

~tratton

ntek

~7.3mm

~O.Smm

lx

lx

77.7 mm 12.3 kW 16.5 hQl

IX 77.7 mm 12.3 kW 16.5 h_Q]_

rx

3600 RPM

3600 RPM

3600 RPM 1800 RPM 9Amps

70mm 13.4 kW 18.0 hJJl 39.3 N.m

70mm 13.4 kW 18.0 hQl 39.3 N.m

77.7 mm 10.8 kW 14.5 hp]

3600 RPM

3600 RPM

3600 RPM

1800 RPM 16 Amps 33.3 kg

1800 RPM 16 Amps 33.3 kg

1800 RPM

1800 RPM

1800 RPM

~ Amps

~Amps

~Amps

77.7 mm 12.3 kW 16.5 hpl

Page 14

Transaxle Design & Performance KR7319 Model & Type:- Hydrostatic Fluid

KR7320

KR7321

KR7322

KR7323

KR7324

Drive through Gear Transmission & !Tl ff T TuffTorq TuffTorq rruffTorq Tuff Torq TuffTorq Differential + Hydrostatic Bypass Dis- K~ AEorq K46AE K46AE K46AE K46AE K46AE engagement + Internal Wet Disk Brake + External Reservoir Tank ~round Speed f-Fo_rw _a _r_d --+0_-_10_.3_ k_m ....:../_ h +o_ -1_0_.3_km ---'--/h-+-~--10_._3_km _,/_h-+0_-_ 10_.3_k_m...:../_ h +-~--1_0_.3_km ---'--/h-+-Q_-_ 10_._3_km _,/-j h (Infinitely Variable) Reverse ~-5. 1 km/h ~-5.1 km/h ~-5.1 km/h IQ_-5.1 km/h ~5. 1 km/h Q_-5. 1 km/h Lubrication Q!picity:2. 1 Utres 2. 1 Utres 2.1 Utres 2.1 Utres 2. 1 Utres 2.1 Utres Dry Mass 12.5 kg 12.5 kg 12.5 kg 12.5 kg 12.5 kg 12.5 kg

6

Mowing Attachment KR7319 Design & Performance

KR7320

KR7321

KR7322

KR7323

KR7324

~ox

Cox Cox !Cox Cox !Cox 7600J 7599!

7499!

74991 75991 7600J Engine PTO Shaft Mounted Electromagnetic Clutch/Brake, Spring Tensioned, Single V Belt, i4 Parallel Unk Points (2 Adjustable).

Model ifype

1 Spindle, Right Side Disharge, 2 Swing Back Blades Cut Width 2 Spindle, Right Side Dis~arge, 4 Swing Back Blades Cut Width 2 Spindle Counter Rotat1005mm ing,Rear Discharge, 2 Cut[40'1 er Bar Blades Cut Width ~nti-scalp Roller ~Adjustable

~ Adjustable

1 Rear Fixed

1 Rear Fixed

14 Adjustable 14 Adjustable

~ut Height Range (lo Posi00<1) 25-80 mm

25-80 mm

25-80 mm

25-80 mm

25-80 mm

25-80 mm

!Grass catcher Design & KRJ 319

KR7320

KR7321

KR7322

KR7323

KR7324

Performance

805 mm [32'1

805 mm [32'1

1005 mm [40'1

1005 mm [40'1 1005 mm [40'1

ifype:- Knit Bag with ntemal Frame

External Top External Top Ieever Tilt to . . . . ~~"over Tilt to 'Emp~ Retract- Not applicable Not applicable Not applicable Not applicable IE~p~ Retract-

!Grass capacity

ing Lever 185 Litres

Miscellaneous Minimum Uncut Grass Diameter Lett Tum) Maximum Grass Cut per Hour Minimum Turning Di- Lett Tum ameter (Inside Back Right Tum Tyre)

KR7319

KR7320

KR7321

KR7322

KR7323

KR7324

1085mm

1348mm

1300mm

1300mm

1348mm

1085mm

10300m2

10300m2

l8200m2

~200m2

10300m2

10300m2

940mm

940mm

I940mm

940mm

~40mm

~40mm

1330mm

1330mm 12N24-4 9Piate, 190CCA 20 Amps 55 Watts

1330mm

1330mm

1330mm

1330mm

12N24-4 ~Plate, 190CCA 15 Amps 35 Watts

12N24-4 9Piate, 190CCA 15 Amps 35 Watts

12N24-4

12N24-4 ~Plate, 190CCA 15 Amps 85 Watts

12N24-4 9Piate, 190CCA 20 Amps 55 Watts

Battery (12 Volt) Fuse (12 Volt) Blade Type Headlamp Globe Maximum

Maintenance

ing Lever 185 Utres

KR7319

KR7320

KR7321

KR7322

~Plate,

190CCA 15 Amps 35 Watts

KR7323

KR7324

Fuel

Unleaded Petrol, Regular or Premium jsAE 30 ,A.P.I. Engine Oil (above+ 4"C) SAE 30 A.P.I. "SF","SG","SH","SJ" 'SE'' "SF" "SG" "SH" !Transaxle Oil jsAE 10W-30 A. P.I. Class "CD" !Champion !Cham~ham pion!Champion!Champion~park Plug RC12YC pionRC12YC ~12YCGap ~1 2YCGap i9<:12YC Gap !Gap 0.76mm k;ap 0.76mm 0.76mm ~.76mm 10_.76mm Mower Blades & Fasteners 20FF 20FF KIT154 SKIT54 ~KIT54 pi<IT41 k:ox Part No ~KIT41 Drive V Belt Cox Part No tv32 ~32 ~32 ~32 ['.1_32 Mower V Belt Cox Part No IV27 V28 IV25 I\J25 1V2s

!Champion~12YCGap

[options b il Drain Valve Cox Part No Mulching Kit Cox Part No

18/10/2007

KR7319

KR7320

~.76mm

KIT154 ~32

27

KR7321

KR7322

KR7323

KR7324

~~"67

~67 ~726

~67

~67

0726

Page 15

.

Series 73011 :- Chassis components (Sid e Discharge)

18/10/2007

Page 16

Series 73011 :- Chassis Components (Side Discharge) ITEM 1 2,3,4,5,6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

PART NUMBER 15110 L01 SPMSX12 NM5NT 1511101] 15108 15020 NM6NT W041216 WSR14 SH0620M W040818 BCHSNM8X20 15131 NFM8 15118 13060 14128 14033 13015 AM230 15133 SH0616M W05M202 SH0512C SH0820M W051218 15189 WS050216 15016 15120 15200 14129 14035 PR0306 BCHSNM6X20 15239

15119 15124 14165 14122 15116 15117 15156 15115 51,52,53,54 DEC 122 DEC 123 DEC 115 55,56,57,58, DEC 110 59,60 15011 DEC 111 61,62,63 DEC112 15121 64 B0620C 65 AM249 67 W061216 68 NF06CN 69

so

15107 18/10/2007

DESCRIPTION Bonnet Latch Assy Screw Nut Headlamp Bracket Bonnet Bracket Seat Support Fastening Strip Nut Washer Seal Washer Screw Washer Bolt Muffler Guard Panel Nut Baffle-Engine Bonnet Seal Seat Spring Seat Spring Cap Seat Mount Pin 280mm Square Bush Seat Support Screw Washer Screw Screw Washer Seat Support Spacer Sleeve Spring Lock Washer Knob Mudguard Chassis Square Plug Square Bush Rivet Bolt Seat Pedal (Refer Motion Control Components) Trim L=480 Trim L=SOO Trim L= 75 Non-Skid Step Through Non-Skid Running Board Left Non-Skid Running Board Right Non-Skid Footrest Left Non-Skid Drive Pedal Set Decal Set- Console 10.8kW (14.SHP) Decal Set- Console 12.3kW (16.5HP) Decal Set- Console 13.4kW (18HP) Decal Set-Bonnet

QTY 1 1 2 2 1 1 2 13 9 5 4 3 4 1 4 1 2 2 1 1 2 1 3 4 4 2 2 2 8 2 1 1 1 1 2 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Bonnet Badge Decal Set- Dash 10.8kW (14.SHP) 12.3kW {16.5HP) Decal Set- Dash 13.4kW {18HP) Slot Seal Bolt Con Rod Bush Washer Nut

1 1 1 1 1 1 1 1

Rear Cover Panel

1 Page 17

Series 730ll :- Chassis Com ponents (Rear

18/10/2007

o¡1scharge)

Page 18

Series 73011 :- Chassis Components (Rear Discharge) ITEM 1 2,3,4,5,6 7 8 9 10 11

12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

so

51,52,53,54

55,56,57,58 59 60 61,62,63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

PART NUMBER

DESCRIPTION

QTY

15110 LOl SPMSX12 NM5NT 1511101J 15108 15020 NM6NT W041216 WSR14 SH0620M W040818 BCHSNM8X20 15131 NFM8 15118 13060 14128 14033 13015 AM230 15133 SH0616M WOSM202 SHOS12C SH0820M WOS1218 15189 WSOS0216 15016 15123 15200 14129 14035 PR0306 BCHSNM6X20 15239

Bonnet Latch Assembly Screw Nut Headlamp Bracket Bonnet Bracket Seat Support Fastening Strip Nut Washer Seal Washer Screw Washer Bolt Muffler Guard Panel Nut Battle- Engine Bonnet Seal Spring Seat Spring cap Seat Mount Pin L=280 Square Bush Seat Support Screw Washer Screw Screw Washer Seat Support Spacer Sleeve Spring Lock Washer Knob Mudguard Rear Discharge Chassis Square Plug Square Bush Rivet Bolt Seat Pedal (Refer Motion Control Components) Trim L=480 Trim L=SOO Trim L= 75 Non-Skid Step Through Non-Skid Running Board Lett Non-Skid Running Board Right Non-Skid Footrest Left Non-Skid Drive Pedal Set Decal Set- Console 10.8kW (14.5HP) Decal Set - Console 12.3kW (16.5HP) Decal Set - Console 13.4kW (18HP) Decal Set - Bonnet Bonnet Badge Decal-Warning Rear Discharge Decal-Height Adjust Decal Set- Dash 10.8kW (14.5HP), 12.3kW (16.SHP) Decal Set- Dash 13.4kW (18HP) Slot Seal catcher Panel Upper catcher Bracket Lett catcher Bracket Right Lower catcher Panel Slide Adjustment Bracket Mudguard-catcher Cover Seal Screw Washer Seal Washer Screw Nut Bolt Con Rod Bush Washer Nut

1 1 2 4 1 1 2 13 9 5 4 7 4 1 4 1 2 2

15119 15124 14165 14122 15116 15117 15156 15115 DEC122 DEC123 DECllS DEC110 15011 DEC108 DEC111 DEC112 15121 15152 14148 14149 15153 15154 15182 SPM5X20 W030820 WSR12 SH0825M NM8NT B0620C AM249 W061216 NF06CN

18/10/2007

1 2 1 7 16 4 2 2 2 8 2 1 1 1 1 2 2

1 1 1 1 1 1 1

1 1

1 1

1 1

1 1 1

1 1 1 2 1 2 4 2 6 6 1 1 1 1

Page 19

Series 73011 :- Engine Control Components (14.5 HP 16.5HP)

(

\

\ \

\

\

\ \ \ \

''

\ \

\ \ \

'

\

'

\

'

\

\ \

I I I I I

~ 9

18/10/2007

'~ I

'

â&#x20AC;˘ I I

Cl

Page 20

Series 73011 :- Engine Control Components lO.SkW (14.SHP) & 12.3kW (16.SHP) ITEM

PART NUMBER

1 2

15137

DESCRIPTION

QTY

Engine 10.8kW (14.5HP) & 12.3kW (16.5HP) B&S Muffler Bracket 12.3kW (16.5HP)

1 1

Muffler B&S

1

4

15229

Exhaust Deflector

1

5 6

STF0410

Screw

2

Screw 1/4" X 3/8"

4

3

Exhaust Gasket B&S

1

8

15136

Exhaust Pipe 12.3kW (16.5HP)

1

9

CHSS0512C W06S

Screw

2

Lock Washer

4

STF0618 15235

Screw Battery Lead Black

4

7

10 11 12

1

13

W051218

Washer

1

14 15

SH0508C

Screw

1

AM265

Battery Lead Red L=490

1

16 17

N04C

Nut Wiring Harness-Engine 12.3kW (16.5HP)

1

18

14095 W030820

13112

1

Throttle Control10.8kW (14.5HP) & 12.3kW (16.5HP)

1

PR0306

Washer Rivet

2 2

Fuel Tank Petrol Cap

1

22

14024 231126

23

AM294

Fuel Tank Grommet

24 25

AM293

Fuel Tap

1 1

14107

Fuel Une 180L

26 27

B08100M

Bolt

1 1

14072

Battery & Fuel Tank Clamp

1

28

AM295 AM007

Spark Plug Spanner

1

29

Plug Spanner Tommy Bar

1

30

DEC085

Decal-Fuel Tank Warning

1

19 20 21

18/10/2007

1

Page 21

Series 73011 :- Engine Control Components 13.4kW (18HP)

I I I

I I

I I

~ 9

18/10/2007

I

I

I

ÂŽ---!

~

T I

I

~

~

Page 22

Series 73011 :- Engine Control Components 13.4kW (18HP) ITEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

PART NUMBER

15139 80025 SH0820M

15138 W06S STF0618 13114 WS050216 W051218 13117 N04C 13113 15033 W030820 PR0306 14024 231126 AM294 AM293 231136 B08100M 14072 AM295 AM296 DEC085 B0840M NHM6 15231 15232 SPMSX12 AM096 NM5NT 15140 15034

13206

18/10/2007

DESCRIPTION

Engine 13.4kW (18HP), 2V Cyl B&S Muffler Bracket 13.4kW (18HP) Muffler B&S Exhaust Deflector Screw Screw 1/4" X 3/8", B&S Gasket 13.4kW (18HP) B&S Exhaust Manifold 13.4kW (18HP) Exhaust Manifold Bolt 13.4kW (18HP) B&S Lock Washer Screw Battery Lead Red L=260 Spring Lock Washer Washer Battery Lead Black L=570 Nut Engine Wiring Harness 13.4kW (18HP) Throttle Control 13.4kW (18HP) Washer Rivet Fuel Tank Petrol Cap Fuel Tank Grommet Fuel Tap Fuel Une Bolt Battery & Fuel Tank Clamp Spark Plug Spanner Plug Spanner Tommy Bar Decal-Fuel Tank Warning Bolt Nut Hot Air Baffle 13.4kW (18HP) Left Hot Air Baffle 13.4kW (18HP) Right Screw Clip Nut Spacer Choke Control 13.4kW (18HP) Oil Drain Valve 13.4kW (18HP)

QTY 1 1 1 1 2 4 2 1 4 4 4 1 3 3 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Page 23

Series 73011 :- Electrical Components

1&

? ~\

~v .,_.

10

("

/

/ /

/

/ /

~

3

I

I

I I

I

9

37 38

18/10/2007

Page 24

Series 73011 :- Electrical Components ITEM PART NUMBER DESCRIPTION

QTY

1

AM109

Battery

1

2

14097

Battery Pad

2

3

13114

Battery Lead Red L=260

1

4

14130

Battery Terminal Cover

15235

Battery Lead Black L=330, (13.4kW (18HP) ONLY)

1 1

5

Battery Lead Black 3 Term, Refer Engine Component, 10.8kW (14.5HP) & 12.3kW (16.5HP) Screw M6 X 16

2

Nut M6

2

Main Wiring Harness (Comes with 15amp fuse)

1

9

Engine Wiring Harness (Refer Engine Components)

10

Battery Lead Red (Refer Engine Components)

1 1 1 1 1

6 7 8

11

15144

12

13125

Seat Switch Ignition Switch 6 Term

13

AM015

Ignition Key Pair

14 15

AM229 14124

Light Switch Incl Wire

1

PTO Switch Incl Back Plate

1

16

FUSEB20

Blade Fuse 20amp

1

Blade Fuse 15amp (supplied with harness)

1

Oil Pressure Lamp Wiring Harness (13.4kW (18HP) ONLY) Hour Meter

1

17 18 19

SSL

1

15036 AM211 AM289

Oil Pressure Light (13.4kW (18HP) ONLY) Square Red Bush (refer Body Components) (13.4kW (18HP) ONLY)

20

1 1

21

AM159

Solenoid

1 1

22

SH0616M

Screw

2

23 24

NM6NT

Nut

2

N04C

Nut

2

25 26

14019 14020

Clutch/Brake Switch

1

Clutch/Brake Switch Cover

1

27 28

SPMSX20 NM5NT

Screw Nut

2 2

29

232201

Electromagnetic Clutch/Brake Headlamp Bracket (Refer Body Components)

1 1

30 31

CABLETIES

Cable Tie

2

32

13331 15109

Connector

2

Head lamp

2

15132 W052003

Globe Washer

2

36

PR0308

Rivet

1

37

AM096

Clip

1

38

W030820

Washer

1

33 34 35

18/ 10/2007

2

Page 25

Series 73011 :- Steering Co mponents

18/10/2007

Page 26

Series 73011 :- Steering Components ITEM

PART NUMBER

1

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

20 21

2223 24 25 26 27

28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

72 73 74

15105 14005 14008 15146 NM12NT 14006 AM336

C02 GNTF3 14009 N06F RE3/8"!NTSTUD WS06081.5 13242 B0850M NM8NT W203902 15112 AM021 BB204212N TT650X6 SlU650X6 13107 WS06081.5 B0620F 14074 14014 14012 14017 14058 14018 B0624F WS06081.5 N06F B0620F 14071 SH0816M NM8NT AM337 15145 N08F RE1/2"1NT 14057 W081616 W122414 14035 14011 14013 WS050216 14015 B0830M WOSM202 5H0816M W061216 B0628F 15173 W$06081.5 N06F 13012 14164 STF1010 14162 SK09 B0830M SW14 W052003 WS050216 SHOS12F 15011

18/10/2007

DESCRIPTION

QTY

Olassis Front Axle Beam Stub Axle Left Hand Steering Arm Key Steering Arm Nut Stub Axle Right Hand Shaft Sealing Washer Ordip Grease Nipple Steering Rod Incl Nuts Nut Stamp Rod End Spring Lock Washer Front Axle Pivot Pin Bolt Nut Washer Rim Bearing Spacer Sleeve Ball Bearing Tyre&Tube Tube Washer Spring Lock Washer Bolt Front Wheel Hub cap Steering Mount Bracket Gear Sector Pivot Gear Sector Stop Gear Sector Steering Sector Cover Plate Bolt Spring Lock Washer Nut Bolt Oamp Post Screw Nut Stamp Rod End Steering Arm Rod Nut Stamp Rod End Pinion Washer Washer Red Square Bush Pinion Mounting Bracket Pinion Adjusting Bracket Spring Lock Washer Steering Tube Bolt Washer Screw Washer Bolt Spacer Sleeve Spring Lock Washer Nut Ranged Bush Steering Column Screw Steering Shaft Woodruff Key Set Bolt Steering Wheel Washer Spring Lock Washer Screw Kingcat Badge

1 1 1 1

1

2 1 4

2 2 1

2 7

2 2 2 4 2 1

2 3 2 2

1

2 2 4 1 1 7 4 1 1 1 1 1 1 1 1 1 1 4 1 1 2 4 1

1 1 1 1 3 1 1 1 1 1 1 1

Page 27

Series 73011 :- Drive Components

18/10/2007

Page 28

Series 73011 :- Drive Components ITEM NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

so 52 53 54 55 56 57 58 59 59 60 61 62 63 64 65 66 67 68 69

15241 14022 W05M202 B0860M W051218 NM8NT W122414 14126 14001 C02 14075 15113 TI850X8 TU850X8 W061216 SH1025M 14094010 B08100M 15209 BCHSNM8X20 NFMB B0840M AM175 15240 232201 W072606 WS071006 W071416 B0748F B0756F 14028 AM017C1 14070 PIVBB20SPA90 14069 WS050216 SH0830M PIFBB02 14025 SH0825M AM145 B0850M 15029 SH0820M 14032 NHTMB 15226 14134 V29K 15247 15247 15176 SH0825M 14025 PIFBB02 BOSSOM PIVBB17SPA71 15243 NCM8X3.2 WS050216 NMBNTl

18/10/2007

DESCRIPTION Chassis (Refer Body Parts list) Transaxle, Hydrostatic, Tuff Torq, Model K46 Bracket, Thrust, Hub Washer, Flat Bolt Washer, Flat Nut Washer, Flat Key Hub, Wheel, Acfaptor Circlip, Ext, 'E' Type Cap, Hub, Rear Wheel Rim Tyre, Inc Tube Tube Washer, Flat Screw Pillar, Transaxle Mounting Bolt Bracket, Brace, Tuff Torq Transaxle Bolt Nut Bolt Key Pulley,Engine Clutch/Brake, Electromagnetic Washer, Flat Washer, Lock, Spring Washer, Flat Bolt Bolt Arm, Belt Tensioner Bush Sleeve, Pivot, Arm Idler, V Belt, Ball Bearing, Sealed Boss, Idler Washer, Lock, Spring Screw Idler, Flat, Flanged, Ball Bearing, Sealed Boss, Idler Screw Spring, Extension Bolt Guide, Belt, Rear Screw Bar, Mounting, Belt Guide Nut Restraint, Electric Clutch/Brake Bush, Spacer, Belt Guide Bar Belt Sub-Assy, Bridge, Idler,Fixed Boss, Idler Screw Boss, Idler Idler, Flat, Fig, Brg, Sealed Bolt Idler, V Belt, Brg, Sealed Bracket, Bridge, Idler Nut Washer, Lock, Spring Nut

QTY 1 1 2 4 5 12 15 4 2 2 2 2 2 1 1 6 6 2 4 1 2 2 3 1 1 1 1 1 1 1 1 1 1 1 1 1 5 1 1 1 1 1 2 1 4 1 2 1 2 1 1 1 1 2 3 1 1 2 1 3 2 1

Page 29

Series 73011 :- Drive Control Com ponents

18/10/2007

Page 30

Series 73011 :- Drive Control Components ITEM PART NUMBER DESCRIPTION

QTY

1 2 3 4 5 6 7 8 9 10 11 12 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 48 49 50 51 52 53 54 55 56 57

1 1 2 1 1 1 8 1 3 1 5 1 2 1 2 2 1 1 1 1 1 2 3 2 2 1 1 1 1 1 2 2 1 1 1 3 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2

15204 AM230 13049 SH0616M W041216 NM6NT 14028 B0648C 14067 AM337 NF06CN N06F 15203 AM020 B0620C 15208 W071416 SH0825M RE516INT NM8NT N05F 15205 14040 13028 13029 W061216 RP01 15202 B0628F 14100 WS06081.5 N06F AM288 15207 15206 14101 15211 SH0624F B0624F 14099 AM328 W102003M N06CN 14047 N05C 14050 W051218 14038 14031 RE38INTSTUD 15210 SH0620M

18/10/2007

Chassis (Refer Body) Transaxle (Refer Drive Components) Pillar (Refer Drive Components) Tensioner (Refer Drive Components) Mechanism (Refer Cutting Ht Adjustment Components) Hydro Drive Pedal Square Bush Drive Pedal Pivot Pin Screw Washer Nut Belt Tensioner Ann Bolt Drive Link Spacer Stamp Rod End Nut Nut Link Rod Stamp Rod End Bolt Drive Control Transfer Lever Washer Screw Stamp Rod End Nut Nut Link Rod Clutch/Brake Pedal Pedal Pad Pin Washer "R"Pin Clutch/Brake Link Bolt Stop Bush Spring Lock Washer Nut Spring Brake Transfer Lever Pivot Pin Spring Brake Adjust Link Screw Bolt Roller Spacer Pivot Lever Bush Washer Nut Park Brake Rod Nut Park Brake Spacer Washer Spherical Knob Dedutch Push Rod Stamp Rod End Bypass Lever Extension Screw

Page 31

Series 73011 :- Transaxle Components : > -81 2CO Seill Kol 20 I - Repaor Kot

K-l6AE1

Re•J 8- 10-0 I

-

80

I ~

2·1

68 3

18/10/2007

Page 32

Series 73011 :- Transaxle Components Item P/N 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

so

51 52 53 54 55 56 57 58 59 60

T1A646084163 T1A646024460 T1A646024201 T1A646024230 T19485924252 T19216324360 T1A646024370 T1A646024440 T19215427280 T1A646089510 T1A632029520 T19216829570 T1C655036300 T22252000350 T22351030016 T22351030020 T24311240100 T24421153507 T26476080552 T26476080302 T1A646024480 T1A646099321 T19216824760 T19216324960 T26106100752 T1A646024752 T1A646024761 T1A646024790 T19216825110 T1A646025200 T1A646025251 T19215485310 T24101062020 T19216824210 T19216324240 T19216825210 T19216825230 T1A646025270 T19215425310 T1A646025400 T168T2025280 T19216327060 T19216327100 T19216327160 T19216327170 T19216327180 T1A646029910 T1A646029920 T1A646029800 T1A646029900 T1A646029851 T1A646029350 T22137120000 T22351030025 T22351060036 T22351060040 T24311000140 T26776120002

Item P/N

18/10/2007

Description Housing (Lower Reservoir Tank Tube Oamp, Miniature Vent Valve 15 Magnet 28*3.5 Holder (Magnet Oil Seal 162203 Spring Shaft, Bypass, B Lever (Bypass Ring 10 Bore Plug 30 Ring 35 Pin 3.0a*16 Pin 3.0a*20 Packing P lOa Seal TC153507 Tapping, Screw 8*55 Tapping, Screw 8*30 Support Tank Center Case Pin (3*9.8 Filter Bolt 10*75 Ids Valve Ids Spring Filter Cylinder Block Cmp Spring (Pump Shaft (Pump RingE 15 Bearing Housing Bearing 51106 Cylinder Block Cmp Washer 12*24* 1 Shaft (Motor Ring 15 Motor Gear (Us Bearing 6202UO Thrust Metal Swash Plate Cmp Bearing K81105 Thrust Plate (A Thrust Plate (B Control Shaft Fulcrum Eccentricity Torsion Spring Control Arm Control Lever Jerky Plate Washer Spring Pin Pin 6.0A*36 Pin 6.0A*40 0-Ring Lock Nut Description

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87

T19216831501 T1A646033520 T1A646033250 T1A646033410 T1A646033420 T1A646033450 TA646033530 T1A646089330 T1A646089340 T19216334261 T19216834270 T19216334280 T19216834350 T19215125350 T1A646036121 T1A646036160 T1A646036171 TA646036180 T1A646036200 T22351050032 T24311000120 T2351040016 T1A646025300 T1A646025323 T1A646083050 T1A646083060 T19215489090

Diff. Gear Kit Final Gear Collar (Final Pinion Reduction Shaft Washer 12* 32*3.2 Reduction Gear (Us Final Pinion Axle Shaft Axle Shaft R Thrust Washer Ring 17 Seal 19* 32* 8 Bushing 19*21 Ring 12.7 Shoe (Brake Arm (Brake Brake Shaft Return Spring (Brake Actuator (Brake Pin 5.0A*32 Packing P12 Pin 4.0A* 16 Spline Collar Pulley B Fan Lock Washer Snap Ring

Page 33

Series 73011 :- Cutting Height Adjustment Components

.-;

-···

.....

.... ....

..... .

: ,, ._

: ·::::. :' ''.

.. ·.

•·. :;

•. ••

21

.~~;?·-~:-~

f'

·.,

.. . '· ·...··....._.

•'

.·.·. ·.

9

·.

.::·.: .

··.·.:.

·-.·.

·..._:.

··.

-

:

... ;-

i_ ........· ·->~_: . -.~-

..·.. ...... .;. ·_

_~,.

15

·'

,·.

7

,.

1(• ... .

~•

...

•

I

~ --:·_·. \~, -· -~-. :·: .•

-~ ·,.,.~:I

(· ,

6

18/10/2007

Page 34

Series 73011 :- Cutting Height Adjustment Components m M

PART NUMBER

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

15106 AM230 13015 SH0616M NM6NT 13016 14048 W071416 C03 B0624C W102003M AM337 N06CN 1402901!

13021 AM012 AM013Q2 AM011 BCHSNM8X30 NM8NT SH0816M W061216 RPOl

Cutter-Axle Beam Unk Square Bush Pivot Pin Screw Nut Pivot Pin Adjustable Link Rod Washer Orclip Bolt Washer Stamp Rod End Nut Cutter Height Adjust Mechanism Pawl Push Rod Spring Pawl Push Rod Button Ratchet Pawl Bolt Nut Screw Washer "R"Pin

18/10/2007

QTY 1 6 1 2 2 1 2 2 2 2 2 2 2 1 1 1 1 1 1 5 4 2 2

Page 35

Series 73011 :- 805mm (32") Mowing Attachment Components

-

18/10/2007

-1--il

Page 36

Series 73011 :- 805mm (32") Mowing Attachment Components ITEM

PART NUMBER

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

B0620F W$06081.5 13107 13052 14108 BB205215N AM021 AM242 B0620C 13128 N06CN 13051 14059 AM076H7 15148 15149 W051216 N05CN 14062 AM017 W052003 W$050216 SH0820M 14077 PIVBB20SPA90 14069 SH0825M AM145 AM328 W061216 C03 14064 PIFBB02 14025 SH0820M 14063 W051218 CP2-512 SH0616C AM037 CP3-220 AM036D9 14157 AM052E1 44 W041216 45 NM6NT 46 47 SH0616M 15013 48 49 AM273 AM272 50 51 AM274 52 SH0612C 53 56 57 SKIT54 58 59 SKIT55 54 SKIT01D1 SMB198SHD 55 SMB198AHD 60 DEC116 61 V25

18/10/2007

DESCRIPTION

QTY

Screw Helical Spring Lock Washer Washer Cutter Pulley Washer Ball Bearing Bearing Spacer Sleeve Bearing Housing Bolt Washer Nut Cutter Spindle Key Cutter Disc Cutter Housing Cutter Guard Washer Nut Cutter Deck Belt Adj Arm Tube Steering Shaft Bush with Collar Washer Spring Lock Washer Screw Belt Tensioner Arm Vee Belt Idler Idler Boss Screw Spring Pivot Lever Bush Washer Circlip Cutter Deck Belt Adj Pulley Mount Flat Idler Idler Boss Screw Cutter Deck Belt Adj Connector Washer Split Pin Screw Cutter Housing Roller Shaft Split Pin Plastic Roller Push On Fastener Deflector Bracket Washer Nut Screw Deflector Deflector Pivot Rod Spring Push On Fastener Screw 805mm (32") Stepped Blade, Bolt, Nut & Washer Set

1 1 1 1 1 2 1 1 4 1 6 1 1 1 1 1 4 3 1 1 2 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 2 2 2 1 1 1 1 4 1

805mm (32") High Uft Blade, Bolt, Nut & Washer Set (Spare Part Only) Blade Bolt & Nut Set Stepped Blade (Set) High Lift Blade (Set) (Spare Part Only) Mowing Attachment Danger Decal Vee Belt

1 1 1 1

Page 37

Series 73011 :- lOOSmm (40") Mowing Attachment Components (side discharge) View A

18/10/2007

Page 38

Series 73011 :- 1005mm {40") Mowing Attachment Components ( side discharge) View A ITEM

PART NO

DESCRIPTION

QTY

1

14092

Right Cover

1

2

SH0616M

Screw

9

3

W041216

Washer

9

4

NM6NT

Nut

9

5

14091

Left Cover

1

6

V33

Vee Belt

1

7

PIFBB02

Bearing Flat Idler

1

8

SH0825M

Screw

1

9

WS050216

Washer

2

10

14025

Idler Boss

1

11

AM264

Spring

1

12

B0620C

Bolt

9

13

N06C

Nut

1

14

NF06CN

Nut

18

15

15219

Belt Tensioner Arm

2

16

AM017C1

Bush I nc Collar

1

17

W052003

Washer

1

18

SH0820M

Screw

1

19

14079

Belt Adjust Arm

1

20

SH0616C

Screw

9

21

N06CN

Nut

4

22

AM052

Deflector Bracket

1

23

15013

Side Discharge Deflector

1

24

AM273

Deflector Pivot Rod

1

25

AM272

Deflector Torsion Spring

1

26

AM274

Push On Fastener

1

27

AM258

Floatation Wheel Bush Sleeve

4

28

AM257

Floatation Wheel

4

29

B0648C

Bolt

4

30

DEC116

Decal-Danger Mowing Attachment

2

18/10/2007

Page 39

Series 73011 :- 100Smm (40") Mowing Attachment Components (side discharge) ViewB

18/10/2007

Page 40

Series 73011 :- 1005mm (40") Mowing Attachment Components (side discharge) View B ITEM

PART NO

DESCRIPTION

QTY

12

B0620C

Bolt

9

14

NF06CN

Nut

18

31

15150

1005mm (40") Side Cutter Deck

1

32

SKIT41

Blade, Bolt, Nut & Washer Kit

2

33 34

SMB137AHD

Blade Set (pr)

2

35 36 37 38

SKIT01D1

Blade Bolt, Nut& Washer Kit

2

39

14085

1005mm (40") Cutter Disc

2

4041 4243

13181

Cutter Spindle I ncl Washer & Nut

2

42

13128

Washer

1

43

NHM20Xl.ST

Nut

1

44

BB205215

Ball Bearing

4

45

AM242

Bearing Housing

2

46

AM021

Bearing Spacer Sleeve

2

47

14084

Washer

2

48

SK09

Woodruff Key Set

1

49

14003

Cutter Pulley

2

18/10/2007

Page 41

Series 73011 :- 1005mm (40") Mowing Attachment Components (rear discharge) View A

18/10/2007

Page 42

Series 73011 :- 1005mm ( 40") Mowing Attachment Components {rear discharge) View A ITEM NAME 1 2 2 3 4 4 5 6 7 8 9 10

11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 28 29 30 31 32 33 35 36 37 38 48 52 53 54

14135 SH0616M SH0616M W041216 NM6NT NM6NT 14091 V27 PIVBB17A88 SH082SM WSOS0216 14025 B0850M 15176 WOS2003 NM8NT_ 1 AM145 WOS1218 RP01 14138 CP2-512 15174 AM328 W061216 C03 15175 AM017Cl SH0820M 14137 B0616C SH0616C NF06CN B0648C AM258 AM25703H N06CN 14161 14165 DEC116 15151 B0620C 15244 SH0612M 15246

18/10/2007

DESCRIPTION Cover, RH, 40" Cutter Rear Disc Screw Screw Washer, Flat Nut Nut Cover, LH, 40" Cutter Deck Belt Idler,V Belt, Brg,Sealed Screw Washer, Lock, Spring Bos,Idler Bolt Boss,Idler Washer,Fiat Nut Spring, Extension, Weight Compensating Washer,Fiat Pin,'R' Connector, Belt Adjuster Pin,Split Arm,Adjust er, Belt,40"Cutter/Catcher Pivot Lever Bush Washer,Fiat Circlip,Ext, "E" Type Arm,Tensioner,Belt,40"Cut-Catch Steering Shaft Bush With Collar Screw Arm, Belt Adj, 40" Cutter Rear Disc Bolt Screw Nut Bolt Flotation Wheel Bush Wheel Nut Deflector,40"Rear Discharge,Biack Trim,Pinchweld, Decai,Danger,Mowing Attachment Deck, Cutter,40"Rear, Model 73,Yellow Bolt Body,Chute,Discharge,Rear,Biack Screw Telltale,Chute,Discharge,Rear,Biack

QTY 1 10 2 8 12 2 1 1 3 2 3 3 1 1 2 1 2 2 1 1 1 1 1 1 1 1 1 1 1 2 6 14 4 4 4 4 1 2 2 1

8 1 2 1 Page 43

Series 73011 :- 100Smm (40") Mowing Attachment Components (rear discharge) View B

18/10/2007

Page 44

Series 73011 :- lOOSmm ( 40") Mowing Attachment Components (rear discharge) View B ITEM

PART NO

37 38

15151

39 40 28 KIT154 29 41 42 43 13181 44 43 13128

DESCRIPTION

QlY

Decal

2

lOOSmm (40") Rear Discharge Cutter Deck

1

Bar Blade Kit

1

Cutter Spindle Inc Washer & Nut

2

Washer

2

44

NHM20Xl.ST

Nut

2

45

66205215

Ball Bearing

4

46

AM242

Bearing Housing

2

47

AM021

Bearing Spacer Sleeve

2

48

B0620C

Bolt

8

49

14084

Spacer Sleeve

2

50

SK09

Woodruff Key Set

51

14003

Cutter Pulley

1 2

18/10/2007

Page 45

-

Series 76001 :- 185 Lit re Bag Rear Mount Grass Catcher suit 73011

.......

OJ

.......

~'-M

.f2 N 0

0

'.J

\

.... ....

.

_..'\

\

I .....--r-1

I

\ \

I

\

I

\

I

\

\ \

\ \

\ \ \ \ \

m '\ \

\ \ \ \

\ \ \

dl'

-o 01

10

o'

(0

..:..

ITEM PART NUM- DESCRIPTION BER 1 14150 Front Frame 2 15129 Top Frame 3 15130 Bottom Frame 4 14153 Catcher Frame Strut 5 15125 Rear Catcher Bag 67 15171 Tilt Lever Bush-Casing 8 15128 Tilt Lever Bush 9 15126 Tilt Lever Handle 10 SH0820M Screw 11 NM8NT Nut 12 15183 Catcher Cover Handle Hole Seal 13 15122 Catcher Cover 14 DECllO Decal- Bonnet, Mudguard, Drive & CE Set 15 14154 Grass Catcher Small Handle B0840M 16 Bolt 17 CABLE{nES Cable Tie 18

0'1

®---.6

AM335

Handle Grip

QTY

1 1 1 2 1 1 1 1 6 8 1 1 1 2 2 6 1

COX INDUSTRIES WARRANTY POLICY NEW MOWER: COX INDUSTRIES warrants in respect of each new ride-on mower sold, that for a period of one (1) year (Domestic use**) or six (6) months Commercial/Contractors/Hire use***) to the original purchaser from the date of purchase, COX INDUSTRIES or an authorised dealer will repair or replace free of charge any ride-on mower parts found to be defective in materials or workmanship under normal use and operating conditions provided that: 1. The mower has been properly and reasonably used, operated, maintained and regularly serviced as per the maintenance schedule during the warranty period.

2. The replacement or repair is performed by an authorised COX INDUSTRIES Dealer. ** "Domestic/Consumer use" means the personal residential household (property use by the original retail purchaser. ***"Commercial use" means all other uses, induding income producing, rental, schools, government departments and charity operators.

NEW MOWER WARRANlY EXTENSION: To triple the warranty period (Domestic use only) from the existing 12 mths to 36 mths or 300 hrs, which ever comes first, all we require is that:1. The warranty registration form be complet ed and returned to COX INDUSTRIES within 14 days from date of purchase.

2. The mower receives an initial service at 5 to 10 hrs or 1 month, then a service as per the maintenance schedule at every 50 hrs or 6 months which ever is the sooner, and those service times and dates are recorded by the COX INDUSTRIES servicing Dealer in the service log provided in this Owners Manual.

PARTS INSTALLED DURING NEW MOWER WARRANlY PERIOD: Warranty coverage for parts installed during new mower warranty period shall consist of the remainder of the new mower warranty period or ninety (90) days, which ever is greater, provided the installation is performed by an authorised COX INDUSTRIES Dealer.

ENGINE AND TRANSAXLE: The engine and transaxle in a new Mower are covered by the manufacturer of that specific product, not by COX I NDUSTRIES. Refer to the engine/transaxle owners manual for details of each products specific warranties.

BATIERY: The battery in a new mower is covered for a period of twelve (12) months by the battery supplier and/or COX INDUSTRIES to the original purchaser from the date of purchase.

ELECTRIC CLUTCH: The electric clutch in a new mower is covered for a period of twelve (12) months by the electric clutch supplier and/or COX INDUSTRIES to the original purchaser from the date of purchase.

18/10/2007

WARRANlY SERVICE : In the event of a need for warranty service contact your local authorised COX INDUSTRIES Dealer.

Date of purchase of machine must be given before warranty daim will be accepted for processing.

WARRANlY REGISTRATION: The warranty registration card must be completed by the dealer with the customer at the time of purchase and returned to COX INDUSTRIES or an authorised Dealer within 14 days.

WARRANTY EXCLUSIONS: 1) The rental of another machine or related equipment while unit repairs are in progress.

2) Telephone, facsimile expenses or other related communication expenses.

3) Transportation and Insurance charges during transportation of failed unit or any part thereof.

4) The labour, parts, mechanical adjustments or lubricant costs which, in the judgement of COX INDUSTRIES or their authorised dealer, are made or should be made as standard maintenance according to the COX-INDUSTRIES maintenance schedule.

5) The replacement of normal maintenance parts such as (mower discs, blades, bolts and nuts, vee belts, bearings, chains and clutch cones) made in connection with normal maintenance services as opposed to manufacturing defects.

6) Any defect caused by alteration, modification, frt:ment of a noni)enuine part or attachment not approved by COX INDUSTRIES. 7) Any defect caused by misuse, negligence, accidents or failure to carry out proper maintenance procedures.

8) Any defect caused by work carried out by other than an authorised dealer.

9) Damage caused by continued operation of the machine after it is known to be defective.

10) Damage caused by racing and similar activities or by overloading.

All implied warranties (save those preserved by stature) are excluded. Liability for consequential damages under any and all warranties are excluded to the extent exclusion is permitted by law.

To the extent that it is not prevented from doing so from statute, the manufacturer will not accept liability for costs of labour, postage, cartage or delivery to replace faulty materials or parts; or for any loss, damage or accident directly, indirectly, or consequently suffered by the purchaser, operator or any other person or property as a result of such faults whether due to defective materials or workmanship or otherwise The careless or improper use of a machine of this type can be dangerous. The manufacturer or selling agent does not accept responsibility for accident either to the operator, to the owner or t o any person directly or indirectly or to property if such accident is caused by circumstances arising other than by the negligence or default of COX INDUSTRIES.

Page 47

utries (Australia) pty Ltd 70 Landseer Street Acacia Ridge Qld 4110 P.O. Box 6266DC Acacia Ridge Q 4110 Australia PH 07 3323 2222 FAX 07 3344 6233 Web Site Address: www.coxmowers.com.au Email : sales@coxmowers.com.au