Ford 7710 II Tractor Operator’s Manual Instant Download (Publication No.42771010)

42771010

DEAR CUSTOMER - PLEASE READ CAREFULLY

The warranty coverage that is extended to your Ford Tractor is explained in the Warranty and Umitation of Uability, Ford Tractor and Equipment form, Yow: dealerwiU provide you with a copy of the warranty and retain a copy which you have signed, After you read the warranty, ask your dealer to explain any points that you may not understand.

Do not modify or alter or permit anyone else to modify or alter this tractor or any of its components or any tractor function without first consulting a Ford Tractor Dealer. If you have any questions regarding tractor modifications contact Ford Tractor Operations of Ford Motor Company.

A roll over protective structure (ROPS) and seat belt were standard equipment for the tractor at time of factory assembly, If the ROPS was deleted by the original purchaser or has been removed, it is recommended that you equip your tractor with a Roll Over Protective Structure (ROPS) and seat belt ROPS and safety cabs are effective in reducing injuries during tractor overturn accidents. Overturning a tractor without a ROPS or safety cab can result in serious injury or death.

Roil Over Protective Structure (ROPS) safety cabs and seat belts are available for your Ford tractor. If your tractor is not equipped with a ROPS or safety cab and seat belt see your Ford Tractor Equipment Dealer.

Your safety the safety of those around you depends upon the care and good judgment you use while operating this equipment. Read the safety precautions carefully. a complete list of the pre·delivery service checks performed by your dealer, refer to PRE·DELIVERY SERVICE on the upper portion of the following two pages. The first copy is your record of the service performed and the second copy, which is to be removed from the manual, is your dealer's record. MAKE SURE THAT YOU AND THE DEALER SiGN BOTH COPIES. After you have operated yow: tractor for fifty hours, take the manual and your tractor to your dealer. He will then perform the :factory recommended SO·HOUR SERVICE as listed on the lower portion of the following two pages - without charge - except for lubricants, hydraulic oil, or filters replaced as part of normal maintenance. MAKE SURE THAT YOU AND THE DEALER SIGN BOTH COPIES. Your tractor is equipped with a new Ford engine. During manufacturing, the cylinder walls of some engines are sleeved. Both sleeved and unsleeved engines have the same operating characteristics.

PARTS AND SERVICE CATALOGUES AVAILABLE!

Ford Tractor Operations is pleased to announce to owners of Ford tractors and equipment the availability of numerous parts and service catalogues.

To obtain these catalogues merely fill out the order form available from yow: local authorised Ford Tractor-Equipment Dealer. Mail VlIth your remittance to Helm Inc. Your order will be processed promptly.

PRE-DELIVERY SERVICE

CHECK AND ADJUST AS REQUiRED INOPERATIVE SERVICE CHECKS;

20. Hydraulic lift draft control

3. Windsh iald wiper/washer 2 Sflt'h,,'tl

m~if\"lrwlf1t! adjustment

drawbar and pin in

!. Tire pressure Front wheel toe~in 3. Front and rerv wheel disc and hub nuts for tightness" 4 Rear wheel to ,im clamp bolts, lock 0, lack screws

8.

9. Hv,jralJllc

5. condition

6.

7

•

Control rocker for tension and compression loads,,, .. AuxH'3ty service control or remOle

27. Cab door lock operation 28. Seat adjustment 29. intenor upholst!lry.l!im and

control valve

10. Fluid and oil leaks 11. Seat belt and rollbars properly

R 30.

9.

10,

11-

12 13.

oil diesel luel 14. Oil level in injector pump..

15. Fuel level 16. Battery cleanliness, vent Onf"1IrlflS elecln)Mte level, and not less 1 .240 Check all electrical cables and wire routings are away from sharp moving parts and exhaust 18. Power 5reering reservoir 01 I level..

19. Hydraulic system oil level

31.

32.

33 34.

Otl'8(Rtor~ Manual

........ .1 PERFORMANCE SERVICE CHECKS operation including throttle

OPERATIVE SERVICE CHECKS; All operating chacks afe to hi! performed with the tractor at normal temperature.

1. Starter 2 Lights and proper operation

TRACTOR MODEL NO

INSPECTION PERFORMED SAFETY PRECAUTIONS AND WARRANTY EXPLAINED

OWNER'S SIGNATURE

DATE

4.

5.

6, accessories TRACTOR SERIAL NO.

DEALER'S SIGNATURE

DATE

-----------------------.---- ..... ------------50-HOUR SERVICE CHECK AND ADJUST AS REQUIRED

TRACTOR MODEL NO.

INSPECTION PERFORMED SAFETY PRECAUTIONS AND WARRANTY EXPLAINED

TRACTOR SERIAL NO.

r

I

~

OWNER'S SIGNATURE

DATE

DEALER'S SIGNATURE

DATE

PRE-DELIVERY SERViCE

CHECK AND ADJUST AS REQUIRED INOPERATIVE SERVICE CHECKS:

20. Hydraulic lift draft control

3, Windshield wiper/washer 2 speed operation .,,,... ,, .......... ,, ................... ,, ............ 0 4, Heater temperature controL, ................... C1 CJ 5. Pressurizer fan 3 speed operation ...........

22, rod levelling crank for 6, Air conditioner oparetion ........................ 0 7. Ensine maximum no-load idle proper operation """ ... " ......" .. " .. "",....... " .. speed adjustmant and fuel [] 23. Clutch pedal free travel "'."",.", ....." ... " ....

24. Brake pedal free travel, equalization.

8. PTO engagement and disengagement ...

9. Hydraulic system; pedal lock."""""" ............" .. ,,,,,.. ,, ... ,, ...... ,,,, 25. Parkins brake oparation ... "" ......,......"" ....

• Draft and Position Control 26. Cab door operstion and see! operation ........ ,." ........ "., ................. .. condition " ...... ,,,., ...............,,,.,,"" ............... .

• Draft Control rocker for tension 21. Cab door lock operation .......................... . and compression loads .............. ..

28, Seat adjustment "'.... " .....,.......................... , • Auxiliary service control or rarnote 29, Cab intarior upholstery, trim and control valve ........................................... , moldings ".,,, ......... ,., ..... ,, ................ ,... ,., .... CJ 10, Fluid and oil leeks ...................... " ..... """ ... 0 30, Cab window oparation. window 11. Seat belt and roUbars properly props and latches, seal condition" .. " ..... , installed ..... " ........ ,......... ,.. ,., .... ,... "" ..... """". 0 31. Cab SUfi visor operation ........" ..................

32. Cab filter installation ................. '"""" ........ [] 33, Tool box for Operators Manual ...............

34. Sheet metal and peint condition ............. mainspring adjustment ."".................,,".... C1 21. link drawbar and pin in

1. Tira pressura 2. Front wheel toe-in "."., •.. ,...."""",.,.,.", .. ", 0 3, Front and raIIr wheel disc and hub nuts for tightness" ........." .. C1 4. Reer whee! to rim clamp bolts, lock nuts. or jack screws for tightness, ............ ,.. "","' .........."""""" .. , [] 5, Front axle spindle nuts for proper tightness ."...... " ... ,............. ' w .... , ..... C1 6. Front axle support bolts for tightness ... """,." .. ,.... ", .....,.,." ......, .. .,.,., [] 7, Chack front axle differential oil level (Front wheel drive only) ,.."...... " .. ,,, " ....... C1 8. Chack front axle hub oil level (Front wheel drive only) ..,.. ,......., ........ ,.... [J 9, Check front weight mounting bolts for tightness ..... " .... " .. ,., .......... """",......... ,.. 0 10, Radiator coolant level ....................... "" ...., 0 11, All belt tensions ...................,' .... " ............ ,.. i.J 12. Engine oil leveL ...................... " ................. C1 13, Drain diesel fuel filter .............................. ", [] PERFORMANCE SERVICE CHECKS 14. Oil level in injector pump.. ,...................... 0 15. Fuel Ieve! .. "" .. .,.. ,,.......................... ,.....,...... , 0 1, Engine operation including throttle 16. Battery cleanliness, vent openings. and governor operation ............................. 0 electrolyte level. and specific gravity OPERATIVE SERVICE CHECKS: 2. Transmission including clutch ................. 0 not less than 1,240 ......... ., ... " .. " ....,.. ""....' 0 3. Differential lock engagement and 17. Check aU electrical cables and AU oparating checks afe to be performed with disengagement .",., ... ,..... " .....................,.. ,.. LJ wira routings are away from the tractor at normal operating temperatura, 4, Steering controL ........................................ [J sharp edges, moving perts and 1. Starter salety switch operation ............,... 0 5. Brake action ...,............. ,............................... 0 exhaust heat .. ,.. ,.. " ........................", ....." .. " [] 2. lights and instruments for 6, AI! OPtional equipment and 18. Power steering reservoir oil leveL"' ....... [] propar operation .......... ,...........,........... " ..... [] accessories ..,.... ,.. ,........ ,., ............................. C1 19. Hydraulic system oil !eve! ,.",." .. " .. ,.......... [] INSPECTION PERFORMED - SAFETY PRECAUTIONS AND WARRANTY EXPLAINED

OWNER'S SIGNATURE

DATE

TRACTOR SERIAL NO. - - - - - -

DEALER'S SIGNATURE

DATE

5O~HOUR SERVICE

CHECK AND ADJUST AS REQUIRED 1, Change Engine Oil and Filter 2. Change Hydraulic Inlet Filter .. ,...................... ""......................... ,.,.,.,., ............................. " .. " .. " ................ .

3, Drain Fuel Filter and Bleed System ........................ "" ....................................." .............................."" ....... Cl 4, Change Injection Pump Oil .. ",,,,,...............,, ....,....................... " .. " .. "" ... " ......" ............. " ....................... ..

5, Tighten Pump Delivery Valve Holders""' .. " .. """... ,.. ,......... "" ........... " ......" ....,... ,............ ,... ,,,."",.......... , 6. Chack Cylinder Head Bolt Torques and Adjust Engine Valve Clearance ................................"" ..... " 7, Check and Adjust Belt Tension ..... " ......,........ ,................................................................................,........ ..

8, Chack and Adjust Brake and Clutch Linkage .......................................................................................... 0 9. Check Torque on Front and Rear Wheel Lug Nuts ............ ,...................... " ...... ,,,,,,, ,............." ............. CJ 1(). Chack Torque on Rear Wheel Rim-ta-Disc Clamp Bolts ............................................" ....................... C1 11. Chack Torque on Front Weiqht Clamp Bolts and Weight Hanger Mounting Bolts ......... ,,,,, ..,.... ,,. CJ 12, Change Front Axle Differential Oil {Front Wheel Drive Only} ..... ,......................,........,.,.,... ,.. "." ........ 0 13. Change Front Axle Hub Oil (Front Wheel Drive Only) ............................. " ......................... " ............... []

TRACTOR MODEL NO, ~~~---

OWNER'S SiGNATURE

INSPECTION PERFORMED~SAFETY PRECAUTIONS AND WARRANTY EXPLAINED

DATE

TRACTOR SERIAL NO.

DEALER'S SIGNATURE

DATE

FOREWORD This Manual has been prepared to assist you in the correct procedure running-in, operation and maintenance of your new Ford Tractor. The Manual covers tractors IAlith and less cab where obvious occur both versions are illustrated or described in text Your tractor has built to maximum performance, economy and ease of operation under a IAlide variety of operating conditions. Prior to delivery, the tractor was carefully inspected, both at the factory and by your Ford tractor dealer to ensure that it reaches you in optimum condition. To maintain this condition and ensure trouble-free operation, it is important that the routine services, as specified in this Manual, are camed out at recommended intervals.

Read this Manual carefully and keep it in a convenient place for future reference. If at any time you require advice concerning your tractor, do not hesitate to contact your authorised Ford tractor dealer. He has factory trained personnel, genuine Ford parts and the necessary equipment to carry out your service requirements.

A vehicle identification plate is located under the radiator cap access panel. If your tractor is equipped IAlith front wheel drive transmission, then a similar plate is affixed to the rear of the front casing. For convenience, the numbers shown on the plates should be recorded in the panels beloo; and quoted to your Ford tractor dealer should the tractor require service.

OMroa

Vehicle Identification Plate

Front Axle Identification Plate

Ford policy is one of continuous improvement. and the right to change prices, specification or equipment at any time Without notice is All in this book is subject to production variations. Dimensions and weights are approximate only and the illustrations do not necessarily show tractors in standard condition exact information about any particular tractor please consult your Ford tractor

(i)

SAF TY PRECAUTIONS A careful Is the best operator. Most accidents can be avoided by observing certain precautiot'lS. accidents and take the before operating the tractor. n,.,,,nH1«m who are responsible end so.

THE TRACTOR 1.

Read the Operator's Manual carefully using tOO tractor. Lack of operating knowledge can lead to accidents,

2,

with a RaPS or for safe operation. or injuf!." If your tracior Is not equipped with a seat belt, see your Ford Tractor Equipment Dealer,

3.

If a front end loader is to be installed, always use a FOPS canopy to avoid injury from falling objects.

4,

Use the nandholds and step plates when getting on and off the tractor to prevent falls, Keep steps and platform cleared of mud and debris.

5.

Do not tractor,

9,

10, Continuous long term contact with used

caused skin cancer in animal tests. contact with used engine oiL Wash skin nu,mt)t!u soap and water, OPERATING mE TRACTOR

Apply the parking brake, the P,T,O. lever in the "Off" position, the lift control lever in the down position, the remote control valve levers in the neutral position, and the transmission in neutral before starting the tractor,

anyone but the operator to ride on the for extra riders.

is no safe

6.

Replace aH missing, illegible, or damaged safety decals,

7.

Keep safety decals dean of dirt and grime.

2,

Do not start the engine or operate controis while standing beside the tractor, Always sit in the tractor seat when starting the engine or operating the controls,

3,

Do not bypass the neutral start switch, Consult your Ford tractor dealer if your safety start controls malfunction, Use jumper cables only in the recommended manner, use can result in a tractor runaway.

4,

AVOid accidental contact with the gear shift lever while the engine is running. Unexpected tractor movement can result from such contact,

5,

Do not get off the tractor while it is in motion.

safety. An improperly maintained tractor can be hazardous,

6,

Shut off the getting off

To prevent flre or explosion' keep open flames away from battery or cold weather starting aids, To prevent sparks which could cause an explosion use jumper cables to instructions.

7,

Do not park the tractor on a steep lndlne,

8.

Do not operate the tractor engine in an enclosed building without adequate ventilation. Exhaust fumes can cause death,

9,

If the power steering or engine ceases operating, stop the tractor

SERVICING THE TRACTOR

1.

The cooling system operates under pressure which is controlled by the radiator cap. It is dangerous to remove the cap while the system is hot. Always tum the cap slowly to the frrst stop and allow the pressure to escape before removing the cap

2.

Do not smoke while refuelling the tractor. any type of open flame away. Walt for the engine to cool before refuelling,

3.

Keep the tracior In good operating condition for your

4,

5,

6.

Stop the engine before performing any service on the tractor. hydrau~c/diesel flUid

under pressure can penetrate the skin causing serious Injury, • DO NOT use your hand to check ror leaks. Use a piece of cardboard or paper to search for leaks.

• Stop the engine and relieve pressure OOfore connecting or dtsconnecting lines.

• all connections before engine or pressurlzlng lines, • If fluid is injected into the skin obtain medical attention immediately or gangrene may result.

apply the parking brake before

10. pun only from the swinging dnawbar or the lower unk drawbar in the down position, Use only a drawbar pin that locks in Pulling from the tractor rear axle or upset 11. If the front end of the tractor tends to rise when heavy

front end or front wheel weights, tractor with a light front end.

Do not attempt to service the air conditioning system, It is possible to be severely frostbitten or injured by escaping See your dealer for service.

8.

The fuel oil in the injection system is under high pressure and can penetrate the skin. Unqualified persons should not remove or attempt to adjust a pump, injector, nozzle or any other part of tbe fuel Fa!lure to foJlovJ these instructions can

install not operate the

12. Always set the selector lever in position control when equipment and when transporting equipment. sure hydraulic couplers are properly mounted and \NiH disconnect safely in case of accidental detachment of implement.

Do not modify or alter or permit anyone else to modify or alter this tractor or any of its components or any tractor function without first consulting a Ford tractor dealer.

13, Do not leave equipment in the raised position.

(ii)

SAFETY PRECAUTIONS DRIVING THE TRACTOR

DIESEL FUEL

1.

L

alcohol or blended fuels be added to These com!Anations can create an increased fire or explOSive hazard.

In a dosed container such as a fuel tank such blends are Do not use these more explosive than hlends.

2,

Never f€l11OVe the fuel cap or refuel with the engIne running or hot

2.

To avoid upsets drive the tractor with care and at conlpaltlble v.4th when oper1:l1ing over rough ground. crossing ditches or and when turning comers.

3.

To provide two whee! lock the tractor brake pedals when transporting on roads.

3,

Do not smoke while refuelling or when standing near fuel.

4.

Keep the tractor in the same gear when going downhill as used when going uphill. Do not roast or free wheel down hills.

4.

Maintain control of the fuel fiUer pipe nozzle wben fillIng the tank.

5.

Do not fill the fuel tank to capacity. Allow room for expansion,

6.

Wipe up spilled fuel immediately.

7.

Always tighten the fuel tank cap securely.

5.

Any towed vehicle whose total weight exceeds that of the towing tractor must be equipped with brakes for safe operation.

6.

When the tractor is stuck or tyres are frozen to the ground, back up the tractor to prevent upset

8.

If the original fuel tank cap is lost, it with a Ford approved cap. A non-approved, proprietary cap may not be safe.

7.

Always check overhead clearance, especially when transporting the tractor.

9.

Keep equipment dean and properly maintained.

8.

Dip the tractor lights when meeting a vehicle at night Make sure the lights are adjusted to prevent blinding an oncoming vehlde operator.

11. Never use fuel for cleaning purposes.

North An1er1ca only: Use the Rasher/Tum Signal llghls and SMV sign when travelling on puhl!c roods, both day and night, unless prohihited by law.

SAFETY CAB OR FRAME (Where fitted)

10. Do not drive equipment near open fires.

9.

12. Arrange fuel purchases so that winter not held over and used in the spring.

If your Ford tractor is equipped v.4th a safety cab or frame it must be maintained in a serviceable condition, Be careful when driving through doorways or working In confined spaces with low headroom.

OPERATING THE P.T.O. L

2.

3.

4,

When operating P.TD, driven equlpment, shut off the engine and wait until the P.T.O. stops before gelling off the tractor and dtsconnecting the equipment.

Under no circnmstances: L - - - modify, drill or alter the safety frame or safety cab in any way as so could render you liable to legal prosecution.

Do not wear loose when operating the power take-off or when near rotating eqUipment When operating stationary PT.o. driven equipment, always apply the tractor parking brake and block the rear wheels front and back To avoid injury, do not P.T.O, driven equipment runnig,

5. Make sure the PT.o. and not in use.

the

fuels are

2.

- - - attempt to straighten or weld any part of the main frame or retaining brackets whlch have suffered damage. By doing so may weaken the structure and endanger your

3.

- - - secure any parts on the main frame or attach your cab or frame with other than the bolts and nuts specitied.

adjust, unclog or service the tractor engine is

4,

--- attach chains or ropes to the main frame or cab for puH!ng purposes.

5.

is in position at all times

Ilnr\""'<"'~'n! risks even

your safety you the maximum protection

cap when the P,TO, is Whenever you see this symbol

A

it means:

ATTENTION! BECOME ALEfITl YOUR SAFETY IS INVOLVED!

(ill)

high

ROPS (North America only) ROLL OVER STRUCTURES

PROTECTIVE

ROPS MAINTENANCE INSPECTION

A ron over protective structure (ROPS) and seat equipment for the tractor at belt were time of factory assembly. If the ROPS was deleted by the original purchaser or has been removed, it is recommended that you equip your tractor with a Roll Over Protective Structure (ROPS) and seat belt ROPS are effective in reducing injuries during tractor overturn accidents. Overturning a tractor without a ROPS can result in serious Injury or death.

AND

Mer the first 20 hours of operation and after every 300 hours of operation, or six months, whichever comes first;

1. Check the torque of the ROPS mounting bolts. Tighten, if necessary, as follows: 0.75 in. bolts; 252·308 IbHt (342418 Nm) 1.00 in. bolts: 646·714 IbUt. (876·968 Nml 2, Check the operator's seat mounting bolts and the seat belt mounting parts. Tighten bolts to torque and replace worn or damaged

Roll Over Protective Structure (ROPS), and seat belts are available from your Ford Tractor EqUipment Dealer.

parts.

DAMAGE TO THE ROPS If the tractor has rolled over or the ROPS has been damaged (such as striking an overhead object during transport), the ROPS must be replaced to provide the onginal amount of protection.

Mer an accident, check for damage to the (1) ROPS, (2) operator's seat, (3) seat belt and seat belt mountings. Before you operate the tractor, replace all damaged parts.

DO NOT TRY TO WELD OR STRAIGHTEN THE ROPS.

A

WARNING: Never attach chains, ropes, or cables to the ROPS or Cab for pulling purposes; this will cause tractor to backward. Always pull from the tractor drowbar.

2--Post ROPS

...

A WARNING: If the ROPS cab is . . . removed or replaced, make certain that the proper hardware is used and the recommended torque values are to atta· ching bolts.

A WARNING: Always wear your seat ...

Never wear seat belt if the tractor is not equipped with a ROPS or Safety Cab. FALLING OBJECT PROTECTIVE STRUCTURES (FOPS) When tractors are equipped with front-end load· ers and are not equipped with cabs, it is rp(',r;m'mP1nlic'li the tractor Ford Built Safety Cab (ROPS)

(Iv)

UNIVERSAL SYMBOLS your tractor, various a to the operation symbols are below instruments Engine speed (rev/minx 100)

tV! t~perature control

Hours recorded

~ Hazard warning

coolant temperature

@Neutral

Fuel level

"" Fan

Ai

(il

symbols

•...

II

on the

Remote cylinder • (extend)

4:;':" Remote

Wipe/wash control

(float)

.... 'Tortoise', slow or minimum setting

Engine stop control 'Hare', setting

!•• I Power take-off engage ......

Lights

~

I•

I Power take-off

disengage Hom oil pressure

"r Front wheel drive iii engage

.. ~.. Transmission oil ~ pressure Tum signal

tt Front whee! drive

,

Transmission oil temperature

Itt disengage

Alternator charge

.....

T

(® Parking brake

T Heater temperature

W control

or maximum

arm/lower

OM499A

OM484

(v)

'\to Work ~

CONTENTS foreword safety precautions roll over protective structures (North America only) universal symbols

SECTION

A

.2 4 8 9 9 10 18 20 21 22 30 33 44 50 53

LUBRICATION AND MAINTENANCE lubrication and maintenance chart routine servicing general maintenance

SECTIONC

(iv) (v)

CONTROLS, INSTRUMENTS AND OPERATION tractor controls engine starting/stopping procedure transmission dual power front wheel drive safety cabs operator's seat power take-off belt pulley hydraulic controls remote control valves three-point linkage track adjustment tractor weighting tyre inflation

SECTIONB

Page (i) (U)

SPECIFICATIONS INDEX

(vi)

.2 3 23

--FORD 1110

SECTION A

CON ROLS, INSTRUMENTS AND OPERATION

The following pages in this section detail location and function or the various instruments, switches and on your tractor. to or tractor, study this section carefully and ensure you are thoroughly familiar with all aspects of operation.

This Manual covers tractors IAlith and less cab. Where there are obvious differences in location, appearance or operation of any of the controls, then each version is illustrated or described in the text If in doubt about any aspect of operation of the tractor, consult your Ford tractor dealer.

Particular attention should be paid to the recommendations for running-in to ensure that your tractor 1AIil1 long and dependable seMce for which it was rf,,",nn,>rf

1

PANEL

a

2,

P1"oofmete1"

in this section

2

correct

--FORD 7 7 1 0 - - - - - - - - - - - - S E C T I O N A When the switch is turned on, the rocker switch will internally illuminated. When front is the is brightly lit whee! light intenslty is when front wheel drive is

Key-Start Switch Actuates the starting motor and Thermostart (where fitted). See "KEYSTART SWITCH" in this section for correct operating procedure, 1.

Instrument Panel

1.

2.

3.

Alternator warning light Turn indicator coolant temperature gauge Trailer tum signal indicator llghts (except North America) Proofrneter Fuel gauge Engine oU pressure warning light Air cleaner t€striction warning Dua! power indicator lamps

4,

5.

6.

7.

8.

9.

Engine Stop Control Pull fully 'OUT' to cut the fuel supply to the injectors and stop the engine. The stop control must be pushed fully 'IN' before re·starting the engine.

Cigarette Ughter To operate, push the lighter knob fully in. The lighter will pop out when the electrical element has reached the correct temperature.

HAND CONTROLS AND SWITCHES

An ashtray is provided on the left-hand side of the cab, in front of the parking brake.

NOTE: The following text describes the function of the various switches and hand controls on your tractor. See Figure 2 to locate these features on

Tractor Lights Switch

your tractor.

The rocker switch is of the 3-way type, the rear position being off, the centre position actuating the side lights and the foremost position actuat· ing the headlights. Selection of main or dip beam is by means of the stalk-type switch mounted on the steering column.

Hand Throttle Lever Push forward to progressively increase engine speed.

Fuel Tank Sender Switch

Work Lamp Switch

The switch is used to monitor the fuel level in the upper and lower tanks, See "Fuel Gauge" on page 2 of this section for correct operating procedure.

The rocker switch is of the 3-way type, the front position controlling the front work lamps, the centre position being off the rearmost position controlling the rear work lamps. Front and rear work lamps may be illuminated simultaneously by first moving the switch to the forward position, then qUickly to the rear position.

Front Wheel Drive Engagement Switch (where fitted)

Moving the switch to the centre will tum off the rear work lamps, followed, a short time delay, by the front work lamps. The switch is illuminated when the rear worklamps are on.

Press green section switch to engage the drive to the front wheels. Press the black section of the switch to front drive.

3

Suggest: If the above button click is invalid.

Please download this document first, and then click the above link to download the complete manual.

Thank you so much for reading

....-..r!ilt:COJfiROLS, INSTRUMENTS AND OPERATION--NOTE: The horn, headlight flash and turn signals wilt only operate when the key.start switch is turned on.

Hazard Warning Lights Switch Press the red secti'On 'Ofthe rocker switch (mangle symbol) to 'Operate ali the tum signals simultaneously. The switch is internally iUuminated and will flash in unison with the tum Signals.

NOTE: In North America hazard warning lights are used when driving on the public highway. \tVhen a tum signal is made. the lights on one side of the tractor wiil flash, indicating a tum, while the lights on the other side will burn continuously.

2.

Hand Controls and Switches

1.

2.

3, 4.

5.

6.

7,

Hand throtti(;l I.wer Fuel tank SIilnOer switch Front wh(;le! drMa engagement switch (where fitted)

Steering Wheel Tilt Control The steering I.IIheel may be tilted if the clamp handle is pushed in against spring 'Pfessure and rotated antkloc.k\.W;e. Tighten the clamp when the steering wheel is at the desired angie. To aooid interference with the steering wheel or driver's knee, the handle should point forward and do;..vn after clamping.

Re-position the handle, as necessary.

Key-start switch Engine stop rontrol

Ogarette lighter Tractor lights switch 8. Work lamp switch 9. Multl·fu:nction switch 10. Hazard wamlng lights switch 11. St(;loo'ng ~ tilt control

IMPORTANT: Your tractor is equipped with hydrostatic power steering. Neuer hold the steering wheel against either of the steering stops for more than 10 seconds or for more than a total oj 10 seconds in anyone minute. Fa!lure to observe this precaution may result in damage to the steering system components.

Multi-Ft.metie Switch The stalk-type ~tch is mounted on the steering column. The switch operates the hom, tum signals and headlarnp flash and is also used to select main or dipped beam.

KEY-START SWITCH

A WARNING: Do not use ether with the . . . Therrn'Ostort. If, in an emergency, it is necessary to use ether with Thermostart installed, disconnect the terminal wire from the glow plug on the rear of the intake maniJord and insulate the free end oj the wire.

Press in the·end of the stalk to actuate the hom.

The stalk win operate the right-hand tum signal, if moved clockwise, and the lef1;.hand tum signal, If moved anti·clockwise. The tum signal warning light (and trailer lights, if connected), will also flash when the tum signals are operated.

All tractors have a five-positi'On key-start switch.

See Figure 3 and the following text

NOTE: North America only: The turn signals will only operate if the hazard warning lighl$ are switched on.

Your tractor may be equipped with the Thermostart cold weather starting aid which is effective in temperatures down to -18"C (O¢F). The Thermostart consists of a heating element installed in the inlet manifold VJhen operated b; the key-start switch, the Thennostart will ignite fuel in the manifold prior to it entering the combustion chamber.

With the headllghts switched on, push the stalk downwards to select main beam. The blue warning .light on the proofmeter will also iUuminate.

Pull the stalk back to the central position to select dip beam.

Pull the stalk further back. against spring pressure, to flash the headlight main beam. The sialk wiU automatically return to the central, dip beam position when released.

IMPORTANT: Never push or tow the tractor to start the engine. Doing so may overstress the drive-train and damage the Dual Power.

4