Developments in Designs, Materials & Manufacturing of Cable Accessories

Page 1

Developments in Designs, Materials & Manufacturing of Cable Accessories


CABLE ACCESSORIES

Developments in Designs, Materials & Manufacturing of Cable Accessories

110 INMR速 Q2 2012

INMR Issue 96.indd 110

dEvElopmEnts

in

dEsigns, matErials & manuFacturing

oF

caBlE accEssoriEs

16/05/12 2:44 PM


T

o achieve the optimum balance of cost and performance, accessories for MV and HV cables are increasingly being produced using tailor-made polymeric materials as well as specialized manufacturing processes. At the same time, developments in cable systems themselves are also impacting the design of accessories that are being developed for use both now and in the future. This article, a consolidation of contributions by Jack Qin (China) and Jens Lambrecht (Germany) of Wacker, Rainer Röder of Gardy Technology, Gerhard Mais of Vogel Moulds and Machines and Samuel Ansorge of Pfisterer (all from Switzerland), provides an overview of general market trends for various cable accessories as well as key properties required of the elastomeric materials being used to manufacture them.

Overview

Although one still finds a variety of alternative cable technologies in service worldwide – from gas-insulated to oil-filled – cross-linked polyethylene types have begun to dominate new applications since the late 1980s. At the same time, accessories for these XLPE cables have been undergoing considerable development and improvement over that period, especially during the past decade. The first generations of accessories, for example, were liquid-filled while today more ‘environmentally friendly’, dry types are gaining in preference. Other features demanded these days of cable accessories include flexibility and ease of handling. For example, terminations for GIS or transformer applications are normally installed on-site, meaning that the GIS or transformer would then have to be completed and tested there as well – something that is not always convenient. Recently available pluggable terminations eliminate the need for additional on-site testing and also offer advantages in terms of installation – independent from that of the GIS or transformer that need only be equipped with pre-installed sockets. Customers can then decide later in the project whether a cable or overhead line termination is more suitable. Pluggable bushings for overhead line connections as well as more compact pluggable arresters are now also available, while connections can be made in every cable position – whether horizontal, vertical or somewhere in-between. The ‘heart’ of a pluggable connector system is the socket, which must be capable of providing field control and designed to meet the requirements of different applications. While it will be placed into GIS and transformers, the socket operates in oil or SF6 that have different permittivity factors. Therefore the design of the field control elements must be capable of covering a range of different field strengths, depending on application. HV terminations with silicone housings represent a growing cable accessory segment.

dEvElopmEnts

INMR Issue 96.indd 111

in

dEsigns, matErials & manuFacturing

oF

caBlE accEssoriEs

Q2 2012 INMR® 111

16/05/12 2:44 PM


Future developments when it comes to cables will concentrate on higher voltages, larger cross-sections and new applications. The challenge here is that while cables are already available up to 800 kV, production, transport and handling for such voltages are all very demanding. Achieving increased current capacity will require cable conductor cross-sections to increase from the 2500 mm² that is fast becoming common to 3000 mm² or even more. The trend toward renewable energy sources is also driving a growing need for DC cable links up to 300 kV to connect offshore wind farms to the grid. Accessories for such applications will require different material properties and manufacturers will have to gain the relevant field experience to develop products suited for this emerging market.

Trends in Cable Accessories

Most MV and more and more HV cable installations today are insulated using extruded polyethylene.

Among the key features being demanded today of cable accessories are flexibility in application and ease of handling. Here, the inner aluminum conductor is surrounded by a grading layer made from electrically conductive polyethylene. The main insulating layer and outer conductive grading layer are made of polyethylene, while the outer conductor is covered by an external sleeve. The use of medium and high voltage cables of different lengths requires their connection and integration into substations and overhead lines. It is here is that cable joints and terminations find main application. Whenever a cable is connected to an overhead line or an electrical installation, the outer conductor and grading layer must be removed and the cable insulation covered by a termination. The main tasks of the termination in this regard include:

Sectional view of typical XLPE cable.

• Grading the electric field at the end of the removed outer grading layer; • Covering the polymeric insulation; • Providing the external creepage needed for the pollution conditions of the service environment. At the MV level, terminations have virtually all been made of polymers such as EPDM and silicone for decades and a similar transition to polymeric housings seems to be the trend at higher voltages as well. Silicone-housed HV terminations offer a number of advantages over porcelain including increased safety, less environmental risk and faster installation. For example, depending on voltage class, the time required to install such terminations has been estimated to be as much as 20 percent less than for porcelain housings. When it comes to MV terminations, there has been steady process of design improvements over the years resulting in more cost-effective products with slimmer profiles. Similar advancements in field grading technologies are expected to result in slimmer HV terminations as well.

Cut away of one design of 35 kV termination (left). Example of typical termination design schematic (right).

112 INMR® Q2 2012

INMR Issue 96.indd 112

dEvElopmEnts

in

But cables are not connected only to an overhead line and other installation. More often than not, the connection is to another cable such as when a damaged section must be repaired or a branch needs to be made. This can be accomplished using different

dEsigns, matErials & manuFacturing

oF

caBlE accEssoriEs

16/05/12 2:44 PM


Selected recent applications for terminations

types of joints, whose principal functions include: • Providing proper insulation, especially with respect to the radial electric field; • Grading the electric field at the ends of the cable’s outer grading layer; • Covering the connector while also providing the required mechanical strength.

New, compact and more costeffective solutions can be found in the area of cable joints as well.

compression apparatus on site. There are fewer parts as well, which makes them less costly to produce.

As is the case for cable terminations, the potential for more rapid and less costly installation is now also driving development of pre-molded joints for HV applications. These are increasingly replacing pre-fabricated joints since there are fewer parts and a built-in compressive force is included that eliminates the need for separate

Apart from these types of developments in terminations and joints, a third type of cable accessory – the connector – is now also offering improved and more cost-effective cable solutions. Connectors are used to plug cables into electrical equipment, such as switchgear, transformers, measuring devices, etc. Accurately fitted parts of molded silicone are connected to epoxy resin counterparts to achieve a safe and reliable connection that can be quickly separated whenever necessary. The number of connector designs and added auxiliary equipment is very broad. For example, plug-in arresters can be mounted to ground lightning impulses and this same technology can even be adapted to produce connectors for busbars.

Cut away view (left) of a typical HV termination and schematic of how it grades electric field distribution (top).

Material Requirements & Properties Elasticity, erosion resistance and long-term stability under electrical

dEvElopmEnts

INMR Issue 96.indd 113

in

dEsigns, matErials & manuFacturing

oF

caBlE accEssoriEs

Q2 2012 INMR® 113

16/05/12 2:45 PM


stress are among the most important characteristics required of the materials used to manufacture cable accessories. In the case of joints, reliable electrical interfaces with epoxy fitting parts are guaranteed because of silicone’s pliable nature as well as its inherent ability to generate and maintain lasting mechanical pressure. Example of typical design evolution of 20 kV outdoor termination. First generation (left) consisted of thick walled RTV silicone molded part with over-molded conductive field grading part. Limited mechanical properties of silicone required several sizes to fit all cable cross-sections since it was impossible to slip termination over fitting. Latest designs (right) consist of thin-walled liquid silicone rubber (LSR) and easily slip over prepared cable. Hose-like integrated field grading allows much slimmer design.

In this regard, the superior electrical insulation properties of silicone elastomers, combined with the fact that they resist ageing and feature stable long-term elasticity, is fast making them the material of choice for many cable accessories. For example, in the case of joints, reliable electrical interfaces with epoxy fitting parts are guaranteed because of silicone’s pliable nature as well as its inherent ability to maintain lasting mechanical pressure. The latest generation of dry type cable joints and terminations share a common feature – namely the insulating component including field control elements. This ‘heart’ of every dry type accessory is normally made of silicone and the parts prefabricated and usually tested at the facilities of the manufacturer.

These types of requirements are increasingly being met by specialized grades of silicone elastomers and the use of the right grade for each application is important both in terms of service performance and optimized manufacturing. For example, stateof-the-art field grading for the MV range can be achieved using a silicone with a relative permittivity of about 15. Conductive grades are then used for field grading in HV applications. Similarly, erosion resistant grades of liquid silicone rubber (LSR) or high consistency rubber (HCR) with hardness in the range of 25 to 40 Shore A have been found ideal for cable terminations. Moreover, their high elasticity allows easy assembly without need for additional tools. The most noteworthy benefit of silicone elastomers when it comes to outdoor cable applications such as terminations (especially under polluted conditions) is their intrinsic hydrophobicity. This property is already well understood by the power industry and allows for more economic designs with shorter creepage and less maintenance requirements in comparison with materials such as porcelain.

Multiple-layer-extruded body of typical silicone MV joint (top). Example of new compact MV joints (bottom) produced as multi-layer silicone with integrated connectors.

Pre-fabricated cable joints for 400 kV (top right) are increasingly being replaced by pre-molded joints with integrated stress relief devices (example at left designed for 161 kV).

114 INMR® Q2 2012

INMR Issue 96.indd 114

dEvElopmEnts

in

dEsigns, matErials & manuFacturing

oF

caBlE accEssoriEs

16/05/12 2:45 PM


Manufacturing Needs

Silicone elastomer joints are generally manufactured either by a variety of molding processes or by multiple-layer-extrusion technologies. Cable accessories for all voltage levels and applications these days are increasingly based on silicone, featuring stress cone inner insulation with non-conductive silicone and then the electrically conductive silicone. When it comes to cable terminations, there is either a direct over-molding of the outer insulation or alternatively use of a hollow core insulator housing. In the past, these types of accessories were manufactured mostly using RTV silicone. However, due to pressures to reduce costs and processing times, use of LSR is now increasing. This material has shown good results from a cost perspective as well as in electrical and mechanical design. For example, bonding between the different silicones – conductive and non-conductive – can be achieved through the material’s intrinsic properties, without need for any external bonding agent or primer. Different manufacturing techniques are used, often depending on voltage level of the accessory. For example, a horizontal mold parting line on the silicone stress cone at MV levels is generally accepted. In such a case, typical manufacturing equipment consists of dosing and mixing units for a two-component LSR in a ratio of 1:1. A standard clamping machine (as also used for MV epoxy parts) is close by. The sleeves to be manufactured have a dedicated manufacturing process while the molds too feature a specialized design. The production area can then be set-up with a special venting system as well as closed loop manufacturing and testing processes. Cable systems required by power utilities are moving toward higher voltages and, with this trend, the requirements from the viewpoint of

dEvElopmEnts

INMR Issue 96.indd 115

in

material electrical properties and automated production processes only increase. One particular design of cable termination with stress cone and external insulator, for example, required a more specialized manufacturing set-up since the thickness of the silicone would normally have required a long vulcanization time. But in this case a patented system called AVT was used whereby the two components of the silicone were pre-heated in a heat exchanger and this resulted in a 30 to 50% shorter curing cycle. Any unwanted back grinding was also minimized and this reduced quality control costs as well. In general, as the cable industry receives more and more orders for cable joints and terminations at HV voltages, e.g. up to 500 kV, optimizing production of stress cones that may require up to 80 liters of silicone will become a growing need. Using RTV silicone or even LSR in a non-optimal process could take many hours and it is therefore becoming ever more important to implement automated processes. Their common basic goal is to reduce overall cycle time by integrating each of the individual process steps for the silicone body into one controlled manufacturing process, including: mold preparation; pre-heating; mold filling with LSR; controlled curing; cooling the mold to room temperature; opening the mold; automatic extraction of the core from the silicone body; and cleaning the mold in preparation for the next cycle. In order to achieve high product quality when it comes to large volume HV cable accessories, optimizing process parameters will be critical, meaning controllable inner mold pressure (with no back grinding) and very good material flowability. This way the final accessory will offer the best mechanical and electrical properties as well as the perfect adhesion between the field control part and the insulating silicone.

dEsigns, matErials & manuFacturing

oF

T-connector features three layers of special silicone rubber grades: inner conductive layer; insulating layer; and over-molded outer conductive layer. Examples of connectors for 10 kV applications (right).

Pre-molded silicone cable joint (foreground) features silicone insulating body (blue) and electrically conductive silicone outer layer (black). Mounted joint (background).

First generation silicone-housed terminations feature 14 weathersheds whereas an equivalent porcelain insulator would need much longer creepage and some 27 sheds.

caBlE accEssoriEs

Q2 2012 INMR® 115

16/05/12 2:45 PM


In the case of joints, reliable electrical interfaces with epoxy fitting parts are guaranteed because of silicone’s pliable nature as well as its inherent ability to generate and maintain lasting mechanical pressure. Typical manufacturing schematic for cable joints and stress cones.

Principle of cold shrinkable joint. Pre-fabricated parts are widened and put onto a spiral support. Once support is removed, widened body shrinks down to diameter of cable. This technology requires unique mechanical properties as well as long term elastic behavior and relies on latest generation of silicone elastomer materials.

Summary & Outlook

Applications for cable accessories these days are becoming ever more demanding with respect to mechanical properties as well as the compression set of the materials being used. At the same time, voltage levels are getting higher while overall life cycle costs (including raw materials, production, field assembly and maintenance costs) are all under pressure to be as low as possible. In this type of environment, one type of accessory should ideally be applicable over a range of different cable cross sections. For the future, as cable voltage levels climb, there will be a growing need for further tailor-made solutions to manufacture large silicone-based accessories in the optimal way. In this respect, there will also be a need for ongoing co-operation between the industry that offers cable terminations and joints, manufacturers of the related production equipment and the silicone material suppliers. 

Typical manufacturing set-up and mold for MV accessories made with LSR.

116 INMR® Q2 2012

INMR Issue 96.indd 116

dEvElopmEnts

in

dEsigns, matErials & manuFacturing

Complete 3 phase cable joints manufactured of LSR.

oF

caBlE accEssoriEs

16/05/12 2:45 PM


Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.