Page 1

ONE2SIX

MAINTENANCE AND SERVICE EXTENDED MANUAL

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL Serial Numbers: OTS-0001 – ...

a product of

© 2009 Shuffle Master GmbH & Co KG | All rights reserved | Version: 02/2009


ONE2SIX

MAINTENANCE AND SERVICE EXTENDED MANUAL

Serial Numbers: OTS-0001 – ...

CONTENTS 2

WEEKLY CLEANING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1

SET USER GAME

SHOW FIRMWARE VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3

5 6 7 8 9 4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SET DATE/SET TIME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SELECT LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 OPERATE MACHINE WITHOUT COVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SERVICE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 INSTALLATION AND USE OF SERVICE SOFTWARE . . . . . . . . . . . . . . . . . . . . . 8 EXTENDED LOGBOOK/ TABLE DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 11

RECODING TABLE OF DISPLAY-KEYS FOR SENSORS. . . . . . . . . . . . . . . . . 11 11 TABLE OF LEDS INDICATING BOARD STATUS. . . . . . . . . . . . . . . . . . . . . . . . . 13 12 STEPPER DRIVER BOARD SETUP AND CONNECTORS . . . . . . . . . . . . . . . 16 13 CPU BOARD LEDS, DIP SWITCHES AND CONNECTORS . . . . . . . . . . . . . 16 14 LOCATE SENSORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 15 DISMANTLE MACHINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 16 PROCEDURES FOR MECHANICAL CHECK AND ADJUSTMENTS . . . . 24 17 EXPLODED VIEWS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 18 POWER SAFETY REGULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 10

Thank you for choosing a Shuffle Master Product!

KEEP BOX FOR RETURN Please keep the original packing for the case of factory service.

© 2009 Shuffle Master GmbH & Co KG | All rights reserved


ONE2SIX

Serial Numbers: OTS-0001 – ...

1 

MAINTENANCE AND SERVICE EXTENDED MANUAL

WEEKLY CLEANING

To assure a long time trouble free operation of your one2sixTM a weekly cleaning is required. For the weekly cleaning open cover and remove the wheel by moving the green and red handle in the forward position:

■■

Select SERVICE on the display; follow Display instructions to enter SERVICE mode.

■■

Choose MOTOR TEST

■■ Chose the respective motor and quit with OK repeatedly to let the selected drive turn in different directions.

Apply 99% Isopropyl–Alcohol to a cleaning card and wet clean the respective rollers. Use a dry card to dry up the rollers after wet cleaning. Do this on all rollers at the card input – and separating portion:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

3


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

After cleaning step back through the display-menu or simply switch machine off and on again. DO NOT USE METHYL-ALCOHOL or any other detergents or solvents.

2 

SET USER GAME

Up to 2 User Games can be configured and named. Enter Menu and choose setup:

■■

Select USER GAMES on the display

■■

Choose USER GAME 1 or 2

Adjust the parameters you like to set for the respective game using the arrow buttons, confirm each parameter with OK: ■■

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

4


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

NOTE: The selected number of common cards will always be delivered prior to the first hand of a game. ■■ The last parameter relates to a hand pitched game. If you choose YES, the entire shuffled deck of cards will be delivered to the front desk ■■

Choosing YES will override all other parameters set for the respective user game

■■

Choosing NO confirms all other parameters as set for the respective user game

Finally rename the USER GAME. Select the first letter with the arrow buttons and confirm with OK. Do this for all digits: ■■

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

5


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

After having confirmed the last digit the display shows:

To select the newly customized USER GAME: ■■

Select GAME on the display

■■

Choose USER GAMES

■■

Choose your customized game

3 

SHOW FIRMWARE VERSION

To show the firmware version installed on the one2six shuffler enter the menu and choose „SYSTEM INFO“. ■■

Press „OK“

Display shows the firmware version and serial number.

4 

SET DATE/ SET TIME

To set date/ time on the one2six shuffler enter the menu and choose „SET-UP“:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

6


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

■■

Select „DATE/TIME“

■■

Adjust the parameters you like to set using the arrow buttons, confirm each parameter with

OK:

5 

SELECT LANGUAGE

To alter the language displayed on your one2six shuffler enter the menu and choose „SETUP“. ■■

Select „LANGUAGE“

■■

Select the language you like to set and confirm with OK

6 

OPERATE MACHINE WITHOUT COVER

THIS MODE IS ONLY PERMITTED TO CARRY OUT SERVICE AND MAINTENANCE AND MAY NOT BE USED ON A GAMING TABLE UNDER ANY CIRCUMSTANCES. To operate the machine without cover enter the menu and choose „WITHOUT COVER“. ■■

Confirm with „OK“

If you like to exit this mode, select again „WITHOUT COVER“ or switch machine off and on.

7 

SERVICE MODE

For a quick failure analysis it is recommended to enter service mode and check motors and sensors on demand. To enter the Service Mode enter the menu and choose “SERVICE”. NOTE: Service Mode can be entered only after the removal of all playing cards from the machine. ■■

Follow Display instructions to enter SERVICE mode

■■

Choose either MOTOR TEST or SENSOR TEST

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

7


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

MOTOR TEST: Chose the respective motor and quit with OK repeatedly to let the selected drive turn in different directions: ■■

■■

SENSOR TEST: Operate sensors manually and check on the display if they work properly.

NOTE: Once you operate a sensor, the respective sensor name and current status will be shown in plain language. For sensor allocation to the letters A to P please refer to the sensor caption table in chapter 10 of this manual. ■■

To exit SENSOR TEST quit with OK.

8 

INSTALLATION AND USE OF SERVICE SOFTWARE

The Service Software allows the download and the deletion of the internal log register of the OTS shuffler. The operating system of your computer/laptop should be Windows XP or higher. It may be needed to install USB drivers on your computer if not installed yet. Power up the shuffler; connect it to your computer/laptop via USB cable.

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

8


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

Select the right COM port setting for your application:

Read the log entry:

Safe or print the logbook as needed. Clear the log register of the shuffler if required:

The full version of the Service Software is only available for internal use of Shuffle Master and aligned companies; it allows the set up of the Serial number in case the main board was changed.

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

9


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

To apply a Serial number change, proceed as follows:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

10


ONE2SIX

Serial Numbers: OTS-0001 – ...

9 

MAINTENANCE AND SERVICE EXTENDED MANUAL

EXTENDED LOGBOOK/ TABLE DESCRIPTION

LOG/TABLE INDICATION

DESCRIPTION

Code 00: Cover open

Indicates that the cover was opened or the cover sensor is defective.

Code 01: DC Controller Error

Hardware is defective. Consult technical service.

Code 02: DC Position Error

Hardware is defective. Consult technical service.

Code 03: AC Fail

Hardware is defective. Consult technical service.

Code 04: Too many cards

Indicates that more than the permitted amount of cards for the selected game was loaded.

Code 05: too less cards

Indicates that less than the required amount of cards for the selected game was loaded (Single Deck Operation only).

Code 06: outpusher jam

Outpusher could not reach its end position while outpushing cards. Outpusher was blocked. Check for proper adjustment of the outpusher fingers. Check for proper function of “wheel home” sensor. Check for defective CPU or driver board(s).

Code 07: outpusher index error

Outpusher could not find its home position. Outpusher is blocked or “outpusher home” sensor is defective.

Code 08: wheel index error

Wheel could not find its home position. Wheel is blocked or “wheel home” sensor is defectiveIt will also occur if the wheel is not inserted during starting up of the machine or removed during operation.

Code 09: cards in input area

A card remained at “card position 2” sensor or “card position 2” sensor is defective.

Code 10: inpusher jam

Inpusher could not reach its home position after in-pushing cards. Inpusher is blocked or “inpusher home” sensor is defective.

Code 11: inpusher Index Error

Inpusher could not find its home position. Inpusher is blocked or “inpusher home” sensor is defective.

Code 12: could not leave in sensor 2

A card jam occurred in the input area; “card position 2” sensor is blocked or defective.

Code 13: could not leave in sensor 3

A card jam occurred in the input area; “card position 3” sensor is blocked or defective.

Code 14: could not reach in sensor 2

A card jam occurred in the separator area. Card was blocked or “card position 2” sensor is defective. Check for clean separator rollers and correct gap adjustment.

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

11


ONE2SIX

MAINTENANCE AND SERVICE EXTENDED MANUAL

Serial Numbers: OTS-0001 – ...

LOG/TABLE INDICATION

DESCRIPTION

Code 15: could not reach in sensor 3

A card jam occurred in the separator area. Card was blocked or “card position 3” sensor is defective. Check for clean separator rollers and correct gap adjustment.

Code 16: could not leave outsensor

A card jam occurred in the output area; “output free” sensor is blocked or defective.

Code 17: could not reach outsensor

A card jam occurred in the output area. “output free” sensor could not be reached or the sensor is defective.

Code 18: not used Code 19: not used Code 20: reset occurred

Indicates an internal reset of the OTS. Occurs when the unit is switched on or restarted; also when service mode is left.

Code 21: not used Code 22: inlock jam

Inlock finger is blocked or sensor is defective.

Code 23: inlock index error

Inlock finger could not find its home position. Inlock is blocked or home sensor is defective.

Code 24 – 32: internal errors

Internal error. Consult technical service.

Code 33: wheel blocked

Wheel is blocked or wheel home sensor is defective. It will also occur if the wheel is not inserted in MD mode.

Code 34: sensor calibration initiated

The SD “card take off” sensor calibration is released.

Code 35: sensor calibration failed

The SD “card take off” sensor calibration failed.

Code 36: unknown logbook code

Cover was opened and wheel was removed while shuffling in SD mode.

10  

RECODING TABLE OF DISPLAY-KEYS FOR SENSORS

A

card present

I

wheel empty

B

card position 2

J

output refill = MD and SD output device sensor

C

inlock home

K

not used

D

inpusher home

L

not used

E

card position 3

M

front key

F

output free

N

cover sensor

G

outpusher home

O

outpusher end

H

wheel home

P

not used

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

12


ONE2SIX

MAINTENANCE AND SERVICE EXTENDED MANUAL

Serial Numbers: OTS-0001 – ...

11  

TABLE OF LEDS INDICATING BOARD STATUS

LED

CPU Board 65420

No.:

Ref.:

Bootloader

Common function

Comments

LED0

D2

slow flashing

ON

CPU power OK

LED1

D6

OFF

fast flashing

CPU is working

LED2

D8

not used

ON

internal error detected

OFF

OK

ON

separator modul status OK

flashing

modul lost – restart necessary

ON

input modul status OK

flashing

modul lost – restart necessary

ON

output modul status OK

flashing

modul lost – restart necessary

ON

display modul status OK

flashing

modul lost – restart necessary

ON

DC Motor – wheel drive activ communication

OFF

not activ

LED3 LED4 LED5 LED6 LED7

D9 D13 D12 D11 D10

not used not used not used not used not used

LED8

D15

not used

ON

DC Motor – communication error

LED9

D14

not used

ON

heap memory overflow – system crash – restart necessary

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

13


ONE2SIX

MAINTENANCE AND SERVICE EXTENDED MANUAL

Serial Numbers: OTS-0001 – ...

11  

TABLE OF LEDS INDICATING BOARD STATUS cont.

LED

STEPPER DRIVER BOARD 65418 used as Separator board

No.:

Ref.:

Bootloader

Common function

Comments

LED green

D3

fast flashing

fast flashing

controller is working - modul is OK

ON/ OFF

controller crash – restart necessary

LED red

D2

slow flashing

OFF ON/ flashing

LED

modul crash or HW defective

STEPPER DRIVER BOARD 65418 used as Input board

No.:

Ref.:

Bootloader

Common function

Comments

LED green

D3

fast flashing

fast flashing

controller is working - modul is OK

ON/ OFF

controller crash – restart necessary

LED red

D2

slow flashing

OFF ON/ flashing

LED

modul crash or HW defective

STEPPER DRIVER BOARD 65418 used as Output board

No.:

Ref.:

Bootloader

Common function

Comments

LED green

D3

fast flashing

fast flashing

controller is working - modul is OK

ON/ OFF

controller crash – restart necessary

LED red

D2

OFF

SD take off sensor free – OK

ON

SD take off sensor damped - OK

slow flashing

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

14


ONE2SIX

Serial Numbers: OTS-0001 – ...

12  

MAINTENANCE AND SERVICE EXTENDED MANUAL

STEPPER DRIVER BOARD SETUP AND CONNECTORS

Connectors and DIP SWITCH setup for the use as Separator Board:

Connectors and DIP SWITCH setup for the use as Input Board:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

15


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

Connectors and DIP SWITCH setup for the use as Output Board

13  

CPU BOARD LEDS, DIP SWITCHES AND CONNECTORS

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

16


ONE2SIX

Serial Numbers: OTS-0001 – ...

14  

MAINTENANCE AND SERVICE EXTENDED MANUAL

LOCATE SENSORS

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

17


ONE2SIX

Serial Numbers: OTS-0001 – ...

14  

MAINTENANCE AND SERVICE EXTENDED MANUAL

LOCATE SENSORS continued

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

18


ONE2SIX

Serial Numbers: OTS-0001 – ...

15  

MAINTENANCE AND SERVICE EXTENDED MANUAL

DISMANTLE MACHINE

Locate the six main case fixing screws:

Main case fixing screws Lift both front ends of the case and move them a little outwards:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

19


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

Lift the rear of the machine. Push the case a few millimetres off against the card guide:

Bend the left front end outwards while pushing off the rear end::

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

20


ONE2SIX

MAINTENANCE AND SERVICE EXTENDED MANUAL

Serial Numbers: OTS-0001 – ...

Lift front and rear end at the same time:

If you need access to the very rear of the machine, loosen screws for the case back-part as indicated below:

Screws for case back-part

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

21


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

For the re-assembly of the main case, effect steps in the opposite direction. Fit case in the rear of the machine:

Bend left front end outwards to repass the belt drive:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

22


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

Refit both front ends by aligning the holes with the buttons while pressing the rear down again step by step:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

23


ONE2SIX

Serial Numbers: OTS-0001 – ...

16  

MAINTENANCE AND SERVICE EXTENDED MANUAL

PROCEDURES FOR MECHANICAL CHECK AND ADJUSTMENTS

Before starting with the mechanical check and adjustment procedures please ■■

Ensure that one2sixTM is cleaned properly according to chapter 1) of this maintenance guide

Connect the machine to a computer or PC and read the logbook (and table) according to chapter 8) of this guide ■■

■■

Find out if there were some difficulties during the use of one2six, use chapter 9) for analysis

■■

Use service mode according to chapter 7) to check drives and sensors for proper function.

a)

Correct separator gap adjustment:

To check for correct separator-gap adjustment, remove wheel and insert 0,4mm feeler gauge as shown below:

The gauge should be easily moveable through the gap of the two separator rollers both on the far left and the far right side. If the gap is too tight, check for residues on the separator rollers. Clean them if needed according to chapter one – use forward movement of the SEPARATOR for the lower roller.

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

24


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

If you notice either backlash or the gap is still too tight, center separator block and loosen 4 fixings screws:

Fixing screws separator block

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

25


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

Apply feeler gauge right in the middle and carefully tighten all four screws again:

The gauge should be easily moveable through the gap of the two separator rollers both on the far left and the far right side. b)

Correct set up of outpusher fingers:

Remove the wheel and visually check for parallel adjustment:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

26


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

If the visual check shows some misalignment, perform the following steps for the re-adjustment of the outpusher fingers: Re-insert the wheel. Manually load a batch of 10 cards into the 0-compartment as well as 10 cards in each of the adjacent compartments:

■■

Select SERVICE on the display; follow Display instructions to enter SERVICE mode

■■

Choose CHECK OUTPUSHER

The wheel instantly turns to the output position from which the 0-compartmnent will be emptied. Slightly move the outpusher drive (on the right) by hand in order to get the fingers in contact with cards:

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

27


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

On both sides the fingers of the outpusher have to have the same clearance to the cards in the adjacent compartments. If not, adjust the vertical position of the outpusher fingers accordingly:

c)

Optical sensor set up on Single Deck Front Part (SD card take off):

If problems related to that sensor are reported - e.g. no further cards delivered after the removal of a hand or delivery of cards though the previous hand was not removed yet – it may be a deterioration of the sensor adjustment. Perform the following steps for the auto calibration of the SD card take off sensor: ■■

Select SERVICE on the display; follow Display instructions to enter SERVICE mode

■■

Choose CALIB. SENSOR

■■

Quit with OK and follow further display instructions

NOTE: To achieve a sufficient calibration result, avoid direct light on the sensor area. If needed, protect the sensing area from light by your hollow hand - keep a distance of at least 100mm from the sensing surface. d)

Accurate operation of cover sensors:

Close cover. Cover must be detected by the cover sensors before it mechanically locks. e)

Free movement of wheel:

Check wheel drive without wheel inserted. Move tooth wheel by hand for free, easy going movement and correct belt stress. There should be no rattling whilst turning the tooth wheel.

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

28


ONE2SIX

Serial Numbers: OTS-0001 – ...

f)

MAINTENANCE AND SERVICE EXTENDED MANUAL

Check Serial No.:

Serial no. on type plate and firmware (display) must be identical. g)

Check date and time:

Check correct set of date and time. Adjust time set up if needed. h)

Lights, buttons and keys work well:

Three colours of status LED, green lights of keys are checked. All keys operate well. i)

Display works well:

All signs are correctly displayed. If the display shows weak contrast, perform the following steps: ■■

Select SETUP on the display.

■■

Choose DISPL. CONTRAST, follow display instructions to adjust the contrast

j)

Operational check SD:

Close cover. Cover must be detected by the cover sensors before it mechanically locks. k)

Operational check MD:

Run 500 playing cards (100% plastic) in bridge and poker size. There must be no errors, irritations or strange noises during work. Run 500 playing cards (paper, plastic coated) in poker size. There must be no errors, irritations or strange noises during work. l)

Optical check:

Defined stickers are fitted (common in English language).

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

29


ONE2SIX

Serial Numbers: OTS-0001 – ...

17  

MAINTENANCE AND SERVICE EXTENDED MANUAL

EXPLODED VIEWS

Sheets enclosed – see next pages

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

30


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

basic unit complete

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

31


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

basic unit sheet

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

32


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

case unit

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

33


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

cover unit

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

34


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

display unit

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

35


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

gravitiy feeder/separator unit mechanic

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

36


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

gravity feeder/separator lower rollers

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

37


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

gravity feeder/separator rollers

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

38


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

gravitiy feeder/separator upper roller free wheel

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

39


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

input/gravity feeder/basic unit

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

40


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

input/gravity feeder/display complete

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

41


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

input/gravity feeder roller motors

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

42


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

input/inlock and inpusher motors

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

43


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

input/inlock

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

44


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

input/inpusher

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

45


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

input/lower rollers

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

46


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

input/upper rollers

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

47


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

outpusher drive

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

48


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

outpusher

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

49


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

output roller belt drive

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

50


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

output roller motor assembling

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

51


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

output roller motor

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

52


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

output lower rollers

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

53


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

output upper rollers

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

54


ONE2SIX

Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

power supply

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

55


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

wheel attachment

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

56


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

wheel basic unit

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

57


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

wheel complete

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

58


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

wheel drive motor

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

59


Serial Numbers: OTS-0001 – ...

MAINTENANCE AND SERVICE EXTENDED MANUAL

wheel drive unit

ONE2SIX

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

60


ONE2SIX

MAINTENANCE AND SERVICE EXTENDED MANUAL

Serial Numbers: OTS-0001 – ...

18  

POWER SAFETY REGULATIONS

The power jack has to be close to the apparatus and easily accessible. Further national requirements: Finland, Norway and Sweden: CLASS I PLUGGABLE EQUIPMENT TYPE A intented for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge surpressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in the applicable countries shall be as follows: In Finland: „Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan“ In Norway: „Apparatet ma tilkoples jordet stikkontakt“ In Sweden: „Apparaten skall anslutas till jordat uttag“ Switzerland: Supply cords of equipment having a RATED CURRENT not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC 60884-1 and one of the following dimension sheets: SEV 6532-2. 1991 Plug Type 15

3P+N+PE

250/400 V, 10 A

SEV 6533-2. 1991 Plug Type 11

L+N

250 V, 10 A

SEV 6534-2. 1991 Plug Type 12

L+N+PE

250 V, 10 A

In general, EN 60309 applies for plugs for currents exceeding 10 A. However, a 16 A plug and socket-outlet system is being introduced in Switzerland, the plugs of which are according to the following dimesion sheets, published in February 1998: SEV 5932-2. 1998 Plug Type 25

3L+N+PE

230/400 V, 16 A

SEV 5933-2. 1998 Plug Type 21

L+N

250 V, 16 A

SEV 5934-2. 1998 Plug Type 23

L+N+ PE

250 V, 16 A

Denmark: Supply cords of single-phase equipment having a rated current not exceeding 13 A shall be provided with a plug according to the Heavy Current Regulations, Section 107-2-D1. CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If poly-phase equipment and single-phase equipment having a RATED CURRENT exceeding 13 A is provided with a supply cord with a plug, this plug shall be in accordance with the Heavy Current Regulations, Section 107-2-D1 or EN 60309-2.

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

61


ONE2SIX

Serial Numbers: OTS-0001 – ...

18  

MAINTENANCE AND SERVICE EXTENDED MANUAL

POWER SAFETY REGULATIONS continued

Spain: Supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UNE 20315:1994. Supply Cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UNE-EN 50075:1993. CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UNE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UNE-EN 60309-2. United Kingdom: An apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug, shall be fitted with a „standard plug“ in accordance with Statutory Instrument 1768:1994 - The Plugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those regulations. Note: „Standard plug“ is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug. Ireland: An apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to I.S. 411 by means of that flexible cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory Instrument 525:1997 - National Standards Authority of Ireland (section 28) (13 A Plugs and Conversion Adaptors for Domestic Use) Regulations 1997. Germany: (Gesetz über technische Arbeitsmittel und Verbraucherprodukte (Geräte- und Produktsicherheitsgesetz – GPSG) [Law on technical labour equipment and consumer products], of 6th January 2004, Section 2, Article 4, Clause (4), Item 2). If for the assurance of safety and health certain rules during use, amending or maintenance of a technical labour equipment or readymade consumer product are to be followed, a manual in German language has to be delivered when placing the product on the market. Of this requirement, rules for use even only by SERVICE PERSONS are not exempted.

Specifications may be subject to change.

© 2009 Shuffle Master GmbH & Co KG | All rights reserved

62

One2six ots service maintenance manual extended 02 2009  
Advertisement