Specifications Lubrication and Fuel Specifications

SPECIFICATIONS

All specifications are subject to change without notice. Always consult BUCYRUS to obtain current information before applying critical loads.

Capacities

Bucket Payload 8000 kg RAS Forks, Max Payload 10000 kg RAS Slewing Jib, Max Payload 7000 kg RAS Belt / Cable Reeler, Max Payload 7000 kg Maximum un-braked trailer mass 10000 kg Maximum braked trailer mass Consult BUCYRUS

Standard Ejector Bucket

Heaped capacity (SAE) 3.5 m3 Struck capacity 2.7 m3 Break out force standard bucket tip (hydraulic) 15000 kg Tractive effort, Maximum 21300 kg

Bucket Motion Times

Lift to full raised position 7.0 sec Lower fully to floor 4.0 sec Roll bucket fully back 7.0 sec Roll bucket fully forward 5.0 sec

Weight

Unladen with full tanks and bucket 19000 kg Laden with forks and 10T load 29000 kg

Engine

Type Diesel, turbocharged, and 4 cycle Cooling system Water based radiator Cooling fan Hydraulic driven fan Engine make/model Caterpillar 3126 Displacement 7.2 litre Maximum power 172 kW @ 2200 RPM Maximum torque 720 Nm @ 1400 RPM

Engine Speeds

Low idle 700 RPM High idle 2600 RPM Governed 2100 RPM

Stall Speeds

Converter stall 2100 RPM Full stall 1700 RPM Hydraulic stall 2050 RPM

Fuel Consumption

At full power 37.5 litre/hr Average mine duty 8-30 litre/hr

Start System

Starter motor type Air (Auststart)

Intake Air Cleaner

Type/make Dry/Donaldson Dual element type Primary and secondary

Exhaust Conditioner

Type Flameproof water bath conditioner Make BUCYRUS Exhaust Flame trap Fitted After treatment Catalytic exhaust purifier

Transmission

Type Power shift with forward/reverse modulation Make/model Dana/Spicer 32000 series MHR Speeds, forward and reverse 4

Torque Converter

Type Mounted in transmission, Single element Make/model Dana/Spicer 13.1 integral

Axles

Type Outboard planetary Front axle make/model Dana/Spicer 16D Rear axle make/model Dana/Spicer 16D Differential type Bevel gear and pinion Differential lock type - front Posi-Torque Differential lock type - rear Posi-Torque Overall ratio 31.06:1

Wheels

Make/model 3 piece (heavy duty)

Tyres - Standard

Type Size Ply rating Inflation media Inflation pressure Michelin X mine D2 17.5 x 25 Radial Air 110 psi front, 110 psi rear

Hydraulic Systems

Steering Closed centre, pressure compensated 2500 psi Brakes Closed centre, pressure compensated 2500 psi Bucket/lift Open centre 3000 psi PTO (2 on machine) Open centre 3000 psi Tank type Sealed and pressurised Tank pressure 10 psi

Hydraulic Filtration

Hydraulics return

Steer/brake system

Optional return PTO Return 25 micron replaceable with bypass Pressure10 micron replaceable with bypass In line, 25 micron

Main Hydraulic Pump

Type Gear Open centre Standard pump output @ 2600 RPM 161.2 lpm

Steering/Brake Pump

Type Pressure compensated piston Standard pump output @ 2600 RPM 117 lpm

Cylinders

Type Double acting Rods Case hardened and hard chromed Counterbalance valves Lift and tilt Cushion stops Steering and tilt

Steering System

Control valve Actuation Pressure compensated Cushion relief Closed centre Orbital 2500 psi 3000 psi

Accumulator Steering

Type Piston Quantity x capacity 1 x 5.7 litre Operating pre-charge pressure 900 psi Nitrogen

Accumulator Brakes

Type Piston Quantity x capacity 1 x 1.96 litre Operating pre-charge pressure 900 psi Nitrogen

Bucket System

Control valve Actuation Main relief Open centre Remote hydraulic pilot 3000 psi

Cylinder Reliefs

Lift arm raise 3200 psi Lift arm lower 3200 psi Bucket roll back 3200 psi Bucket dump 3200 psi RAS in port relief 3200 psi RAS out port relief 3200 psi

Electrical System

Type Approved flameproof Voltage 12 V Polarity Floating

Lights

Number /location 2 front, 2 rear Type SETCO High performance approved flameproof

Alternator

Drive Hydraulic Type Customer preference approved flameproof

Service Brake Hydraulic System

Type Reverse modulated, pressure reducing Control valve Open centre Actuation Foot pedal Operating pressure 2500 psi Brake release pressure 1450 psi

Steering

Type Centre articulated, hydraulic

Service Brake

Type Totally enclosed, liquid-cooled Posi-Stop Make/model Dana/Spicer 16150 Application Spring applied hydraulic release Location Each wheel end

Park Brake

Type Totally enclosed, liquid cooled Posi-Stop Make/ model Dana/Spicer 16150 Application Spring applied hydraulic release Location Each wheel end

Articulation

Bearing type and size Pin and spherical bearing (top), bush (bottom) fully sealed Bush material Hardened steel Pin material Hardened steel Degrees of turn either side 43°

Oscillation

Type Rear bolster Bush material Hardened steel Pin material Hardened steel Degrees up and down from horizon 7.5°

Seating (Operator)

Type Cross-seated Make BUCYRUS Suspension Adjustable spring/shock absorption

Canopy

Type Adjustable Protective device MDG1 and MDG17

Pneumatic System

Compressor type Piston engine gear driven Air flow 0.340 m3/min @ 1500 RPM Governed pressure 120 psi Relief pressure 130 psi Air receiver volume 80 litre

Vehicle Speeds

1st gear 2nd gear 3rd gear 4th gear

Maximum Tractive Effort

1st gear 2nd gear 3rd gear 4th gear

4.3 kph 8.7 kph 14.6 kph 24.2 kph

22165 kg 10700 kg 6160 kg 3565 kg

Grade Ability Front to rear

1:4 Side to side (empty) 1:4 Side to side (laden bucket load fully raised) 1:8

Service Capacities

Hydraulic tank Fuel tank Transmission/converter oil Engine crankcase oil Engine cooling system water Axle oil (each) 300 litre 300 litre 40 litre 22 litre 72 litre 35 litre

Overloading equipment could cause personal injury, death or equipment damage. Due to configuration or options these weights can vary up to 20%. Bucyrus recommends that relevant standards and safety procedures should always be used when operating this machine. Removal of protective canopies, doors, safety devices, interlocks and structures etc., could cause serious injury of death. Replacement with correctly torqued fasteners is mandatory.