PSC HANDS-FREE SAFETY TOOLS: CAUGHT- BETWEEN INJURIES

PSC HANDS-FREE SAFETY TOOLS: CAUGHT- BETWEEN INJURIES What is a caught-between? ● A caught-between is a accident in which the whole body or part of the body is pinched or crushed between objects.

Caught-Between Hazards● Moving pipe and casing ● Using tongs and spinning chain ● Working around mobile equipment ● Unguarded moving parts ● Working under suspended loads ● Improper use of hand tools ● Wearing loose clothing ● Using elevators ● Using slips

Always Remember● Use caution around heavy equipment ● Be aware of your hand placement ● Keep hands free when possible ● Never work under a suspended load ● Don’t choke up on tools ● Ensure machine guarding is in place ● Use caution around pinch points ● Never wear loose clothing ● Use hands-free safety tools for hands-safety Never touch a suspended load with any part of your bodyThe most important tool that money can’t buy from Project Sales Corps the tool #1- The Correct Mindset. Accepting and letting go the natural reaction to go close and hold the rigging in place until the tension is taken up to make sure the load is properly slung and balanced needs to be changed. Remember the most hazardous part of a lifting operation is lifting off and landing and its important you are as far away from the load as possible.

TaglinesThese hands-free safety tools are otherwise known as a guideline, guide rope, end line, strap lines or pay off lines depending on which part of the world you are in but the most common term for use of a piece of rope is “Tagline”.

Taglines or restraint lines must be used when rotation or swinging of the load is or may become hazardous or if the load needs guidance. In brief, loads requiring continuous manual guidance while in motion shall be provided with taglines, and required taglines must be used “on loads likely to swing or which need guidance”.

When Must Taglines Be Used?

Taglines must be used whenever any of the following occur1. The load suspended by the crane in a static (non-moving) condition swings, or is likely to swing back and forth(due to wind or other external factors), creating a control hazard.

Not only for the crane operator and banks man, but a landing and placement hazard.

2. The movement of the cranes or boom causes, or is likely to cause the load to swing out of control, creating a hazardous condition.

3. The load rotates, has rotated, or is likely rotate in such a manner as to be out of control, creating a hazardous condition.

PSC LoadGuider Tagline (for Hands-Free Safety Tool lifting operations)Project Sales Corp has brought in the PSC LoadGuider safety tangle free taglines to solve the problems associated with the use of PP ropes. These taglines are specifically designed for the hands free lifting applications. This hands-free safety tools are tangle resistant as the centre rope is wrapped with an outer layer of smaller diameter rope. This resists the tagline turning on itself and wrapping around objects or people. PSC LoadGuider Taglines are designed not to catch on pinch points, as there are no knots or raised surfaces. These are made in Iceland in technical cooperation with a major drilling operator.

The PSC LoadGuider Anti-Tangle Tagline: “Stronger than steel, light as a feather”

Now guiding a suspended load is easier!

PSC Loadguider taglines are tangle resistant as it is designed with a rigid core and stiff over braiding to prevent any turning on itself and wrapping around objects. The patented Helix spiral effect increases grip in wet and slippery conditions. The PSC Loadguider safety taglines are hands-free safety tools that are designed not to catch on pinch points, as there are no knots or areas to snag. Inside the Helix cover is Dynex 75 fibres giving them exceptional strength make it very lightweight for operator handling. This hands-free safety tool is especially made to save the workers from hazardous conditions and protects hands-safety.

A twist lock carabiner 50 m gate opening as per ANSI Z359.12 can now be purchased for use with the PSC Taglines.

PSC SafeGuiderFeatures● High visibility orange coated end for easy safe grip and low light applications ● Quick attach and release ● Economical alternative to our polyex PSC LoadGuider taglines ● High-visibility, impact-resistant nylon casing ● Excellent control ● No knots, tangles or cut-offs ● No trip hazard or risk of being dragged ● Flexible for easy line storage ● Made in USA ● Free tagline grabber hook for retrieving taglines with every 5pcs ordered

PSC Tagline Retriever Tool-

“A safer way to retrieve tool” PSC TRT- A tool designed to safely retrieve taglines without a load handler having to go too close to a suspended load.

PSC Tagline Retriever Tool-TRT: PSC Tagline Retriever Tool is designed to help facilitate ‘hands-free’ lifting and improve safety in handling taglines. This hands-free safety tool is a modified aluminium telescopic boat hook with a rubber buffer at the other hand.

The hook end is used at full extension (approximately 2.1/7ft) to retrieve taglines hanging vertically without a load handler having to go too close to a suspended load.

The rubber buffer is used to push against suspended load to guide them, especially when landing loads in tight or congested spaces. Once again, this allows the operator to remain a safe distance from the load until it has landed and maintains hands-safety.

The poles would normally be fully retracted (for rigidity) during this type of use where there length is 1.2m/4ft. However, they can be used half/extended if required. But if too much pressure is applied, they will telescope in.

The PSC SafeGuider & Tagline Retriever Tool“For Hands-free guiding of crane, forklift loads & retrieving taglines” PSC SafeGuider- the PSC SafeGuider & Tagline Retriever Tool, is a lightweight tool is used for the hands-free guiding, directing of heavy crane, forklift loads and retrieving the taglines and ensuring hands-safety.

Made with an Ash Hardwood pole with a serrated cast aluminium head tested to push loads right upto 600 lbs, this lightweight hands-free safety tool is ideal for manoeuvring suspended loads without taking the hand close to the danger zone.

The PSC SafeGuider & Tagline Retriever ToolFeatures● The head has a serrated ‘S’ design aluminium tool that works on hooking principle on

one end and a reverse hook on the opposite end which allows it to be used in both push and pull applications ● In the other version, a ‘C’ head to help with the manoeuvring of slung loads. ● A dielectric hardwood makes the product safe to use. ● The sand dipped in the sand area on the wooden pole allows for the better grip while working with these tools.

Available in various lengths- 2,3,4,6 & 8 feet length.

push/pull poles- what are these?

Push pull poles aids in “hands-free” guiding, spotting and landing suspended loads, manoeuvring drill pipe and all types of tubular on pipe racks or on the platform, snagging taglines and sling legs, etc.

Push pull poles provide a hands-safety zone to personnel to manoeuvre and guide suspended loads while avoiding pinch points and crush points. With the use of these tools workers do not place themselves in danger by working in an unsafe proximity to hazardous suspended loads.

There are over a dozen hands-free safety tools varieties available from different manufacturers worldwide including the well known Stiffy, PSC Shove-It and PSC SafeGuider from USA, and few from other countries. These are made out of hardwood, aluminium or fibreglass with variations with heads made out of rubber, nylon, aluminium , etc.

PSC LoadGuider Push/PullProject sales corp introduces the new PSC LoadGuider hands-free safety tool- a robust fibreglass push/pull pole fitting with a nylon head to safely manoeuvre loads at all times, by keeping hands-off from a potential pinch and crush injury zone.

PSC Loadguider tool allows a user to maintain a safe distance from the load at all times, thereby mitigating any risk of pinching or crushing the hands and feet while handling suspended loads or manoeuvring loads in tight positions until the load is in its final placement position. This hands-free safety tool is simple to handle and allows users to keep weights, loads, containers at a distance (push) or pull the load towards them.

Features● Extremely lightweight , weighing just over 900 grams and 50” long, equipped with an ergonomic non-slip handle. ● The PSC LoadGuider Tools avoids unnecessary strain on the wrists during manoeuvring operations thus improving hands safety.

The PSC Fingersaver ToolThe PSC Fingersaver checks hands-safety by keeps your hands away from the impact of the hammer on flogging spanner and from pinch points when using impact wrenches.

2G version available in standard 350 mm, Long 900 mm and compact 295 mm.

3G version is available in standard 350 mm, long 900 mm and compact 295 mm.

Features● Lightweight ● Affordable ● Available in 3 sizes ● Easy to operate ● Peace of mind for self and co-worker ● Simple tool to keep hands away from impact zones

●

Vibration absorbing non-slip rubber grip

PSC Chisel and Punch HolderErgonomically designed to provide a comfortable, firm grip while keeping the hands away from the contact point● Tool holders handle efficiently resists sparks and absorbs vibration ● Hassle-free adjustments with the knob at base ● Accommodates chisels measuring upto 1” in diameter.

PSC Lift Assist Manual Lifting AidsA new range of PSC hands-off safety tools (lift assist manual lifting aids) to reduce need for bending thereby improving ergonomics in workplace, and reduce possible chances of hands & finger injuries associated with lifting and carrying the small equipment’s with bare hands.

The manual lifting aids are used with chiksan and bop choke valves, pup joints, fishing tools, pipe, tubing, deck cargo etc.

The PSC TubularGuiderWith the new PSC TubularGuider now reduce pinch and crush related injuries while working with suspended tubular loads. This hands-free safety tool features non-slip grips, locking mechanism and super strong aluminium shaft. The Dual Release uses a spring loaded noose release to extend the cable through the tool to release the tubular or the slide control which

instantly drops the noose from the tool.