Power limitation messages

- Code on display - Error message - Signal Name of Alarm and Cause Solution

E056 - Over Temp. (from external box)

- Yellow LED

Excessive temperature measured inside the inverter's wiring box:

High internal temperature. This error relates to the temperature measured on external boxes (e.g.:TRIO-20.0/27.6kW). • Check that the inverter is not exposed to direct sunlight. Wait for the temperatures to which the inverter is exposed to return to the operating range and for the inverter to cool down. - If the problem (once the ambient temperature has returned to the range) persists, contact customer assistance. Remember to wait the time needed to allow the inverter to cool down

E057 - Vbulk reading error

- Yellow LED

Input voltage (Vin) higher than booster voltage (Vbulk):

The error occurs if the input voltage exceeds the Bulk voltage (voltage on the DC-DC circuit inside the inverter) • It is necessary to measure the input voltage inside the inverter with a voltmeter. - If it is higher than the maximum voltage of the operating range, the alarm is genuine and it is necessary to check the configuration of the PV generator. If the voltage has also exceeded the maximum input threshold the inverter could be damaged. - If it is lower than the maximum voltage of the operating range, the alarm is caused by an internal malfunction and it is necessary to contact customer assistance.

E058 - Pin vs Pout check error

- Yellow LED

Error in the check of Pin vs Pout:

The error occurs if the difference between the measured value of input power and that of output power is greater than the limit imposed internally to the inverter. • Error inside the inverter and cannot be checked externally. - If the problem (once the inverter has been switched off and back on) persists, contact customer assistance.

The equipment can signal possible output power limitations which may occur on the basis of: - settings made by the user - settings required by the grid standard of the country of installation - protective devices inside the inverter The notices of messages are shown on the display.

The following table gives the complete list of power limitation messages relating to string inverters. Some messages may not be used depending on the inverter model installed.

- Message on display - Signal

- LIMxxx% CODE:00 - Display symbol b6

- LIMxxx% CODE:01

- Display symbol b6

Name of Derating and Cause

Power limitation:

The message indicates that the user has set an output power limitation for the inverter. LIM xxx% = Power reduction percentage Examples: LIM 100% = no power limitation LIM 50% = limitation to 50% of the output nominal power

Power limitation for over-frequency:

The message indicates that the user has set a power limitation due to over frequency in order to reduce the maximum output power of the inverter when the grid frequency exceeds certain limits. LIM xxx% = Power reduction percentage Examples: LIM 100% = no power limitation LIM 50% = limitation to 50% of the output nominal power

Solution

• Check the limitation value set in the “Settings > Power Limitation” menu

• Check the limitation value set in the “Settings > Service > OF Derating” menu

- Message on display - Signal

- LIMxxx% CODE:02 - Display symbol b6

- LIMxxx% CODE:03 - Display symbol b6

- LIMxxx% CODE:04 - Display symbol b6

- LIMxxx% CODE:05

- Display symbol b7

Name of Derating and Cause

Power limitation for over-voltage:

The message indicates that the user has set a power limitation due to over voltage (parameter U >(10 min)) in order to reduce the maximum output power of the inverter when the reading of the average grid voltage exceeds certain limits. The sampling of readings is done every 10 minutes (U>(10min)). LIM xxx% = Power reduction percentage Examples: LIM 100% = no power limitation LIM 50% = limitation to 50% of the output nominal power

Anti-islanding power limitation:

The message indicates that a power limitation is active since an "islanding" condition has been recorded. LIM xxx% = Power reduction percentage Examples: LIM 100% = no power limitation LIM 50% = limitation to 50% of the output nominal power

Power limitation due to low grid voltage:

The message indicates that an output power limitation may occur since a low grid voltage (AC) condition has been recorded. LIM xxx% = Power reduction percentage Examples: LIM 100% = no power limitation LIM 50% = limitation to 50% of the output nominal power

Power limitation due to excess temperature:

The message indicates that a power limitation is active since an excess temperature condition has been recorded inside the inverter (This parameter depends also on the power which the inverter must provide since the measurement of temperatures is taken internally and is influenced by the heat dissipated by the components of the inverter itself). LIM xxx% = Power reduction percentage Examples: LIM 100% = no power limitation LIM 50% = limitation to 50% of the output nominal power

- LIMxxx% CODE:06

- Display symbol b6

Power limitation for input over-voltage:

The message indicates that a power limitation is active since an input over voltage (AC) has been recorded. LIM xxx% = Power reduction percentage Examples: LIM 100% = no power limitation LIM 50% = limitation to 50% of the output nominal power • It is necessary to measure the input voltage inside the inverter with a voltmeter. - If it is higher than the maximum voltage of the operating range, the alarm is genuine and it is necessary to check the configuration of the PV generator. If the voltage has also exceeded the maximum input threshold the inverter could be damaged. - If it is lower than the maximum voltage of the operating range, the alarm is caused by an internal malfunction and it is necessary to contact customer assistance.

Solution

• Check the limitation value set in the “Settings > Service > U > (10 min) Der.” menu

• If the inverter remains connected to the grid and the limitation is active, contact customer assistance

• Check that the grid voltage is lower than the minimal voltage. Should this condition persist, contact the grid operator to resolve the problem.

• Check that the inverter is not exposed to direct sunlight. Wait for the temperatures to which the inverter is exposed to return to the operating range and for the inverter to cool down.

- If the problem (once the ambient temperature has returned within the range) persists, contact customer assistance.