Quick Start Card
in.yt-7 North American version ™
1- Connect all outputs & keypads AMP ports (A0 to A4, and C1 to C3) for pumps & accessories. Functions varie per configuration (see next page).
H L C G
G C L H
C1 C2 C3
A0
C1
Optional floating connector (Part #9920-401346)
C2
H L C G
C3
A4
Main power entry connection
A4 A3
A3
A2 A1
A2 A1
Heater connections
C1 - Main keypad connector Heater
Bonding lugs
2- Connect the main power 2.a- Electrical wiring
Light outputs (P34 always on, P35 relay controlled)
CO - Communication links (2 ports) in.touch, in.stik, Aux keypad in.k112, Swim Spa com. cable, etc.
2.b- Heater & pump/accessories voltage P9
L2
P10
N
N
L1
L1
G
G
For 240 V (4 wires)
For 120 V (*3 wires)
Heater voltage
Pumps & accessories voltage
Connect wiring of the electrical service box GFCI. Neutral wire is mandatory.
* If connected to a 3 wire system, any 240 V components will not work.
Verify BROWN common wire connection to tab: P9 - 240 V P10 - 120 V
Verify each WHITE common wire connection to tab:
N - 120 V L2 - 240 V pump/acc.
WARNING! All connections must be made by a qualified electrician in accordance with the national electrical code and any state, provincial or local electrical code in effect at the time of the installation. This product must always be connected to circuit protected by a Ground Fault Circuit Interrupter (GFCI).
3- Select spa configuration (if prompt on startup) 1
2
At first startup the keypad display will show Lx or LLx, where « x » representing the config. number. Some spa packs come with a pre-selected config. and you may skip this step if your system automatically starts up1.
Use the Up/Down key to choose the new low level configuration number.
1
3
Note: For the Color keypad series, select Settings menu, go into Electrical config and choose the appropriate Low level.
Press the Program2 key to confirm the selection. For more information, see our website: www.geckoalliance.com
Note: To re-enter the low level selection menu, hold the Pump 1 key for 30 seconds.
2
Note: If the keypad does not have a Program or Filter key, use the Light key instead.
4- Select breaker current 1
2
98 Press and hold the Program key for 20 seconds until you access the breaker setting menu.
The values displayed by the system correspond to 80% of the maximum amperage capacity of the GFCI.
Note: For the Color keypad series, select Settings menu, go into Electrical config and choose Input current.
For more information, see our website: www.geckoalliance.com
GFCI
b
60 A 50 A 40 A 30 A 20 A 15 A
48 A 40 A 32 A 24 A 16 A 12 A
(10 to 20 A dedicated to 120 V)
3
Use the Up/Down key to select the desired value. Then press the Program key to confirm the selection. Note: If the keypad does not have the Program or Filter key, use the Light key instead.
Configuration selection chart Software #361, rev. 003 Standard config. # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 1
Pump 1
Pump 2
Pump 3
1SP (A3) 12A 1SP (A3) 12A 1SP (A3) 12A 1SP (A3) 12A 1SP (A3) 12A 1SP (A3) 12A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A 2SP (A3) 12A-3A
1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 2SP (A2) 10A-3A 2SP (A2) 10A-3A 2SP (A2) 10A-3A 2SP (A2) 10A-3A 2SP (A2) 10A-3A 2SP (A2) 10A-3A 2SP (A2) 10A-3A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 1SP (A2) 10A 2SP (A2) 10A-3A 2SP (A2) 10A-3A
1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 1SP (C3) 10A 2SP (C3) 10A-3A 2SP (C3) 10A-3A 2SP (C3) 10A-3A _ _
Pump 4
Pump 5
Blower
_
_
_
_
DIR
_
_
X (A4) 4A
_
DIR
_
_
_
DIR
_
X (A1) 4A
_
DIR
_
_
DIR
X (K2-P Tab) 4A
_
DIR
Ozone (O3) configuration1
Filter cycle daily
During filter cycle (C2) 1A During filter cycle (C2) 1A During filter cycle (C2) 1A During filter cycle (C2) 1A During filter cycle (C2) 1A During filter cycle (C2) 1A
During filter cycle with CP (A1) 0A During filter cycle with CP (A1) 0A During filter cycle with CP (A1) 0A During filter cycle with CP (K2-P Tab) 0A During filter cycle with CP (K2-P Tab) 0A
2 * 6 hours (with CP) 2 * 6 hours (with CP)
1SP (A1) 8A 1SP (A1) 8A
_
_
_
_
DIR
_
_
_
X (A4) 4A
_
DIR
_
_
_
_
_
DIR
_
X (A4) 4A
_
DIR
_
_
_
DIR
_
_
X (C2) 4A
_
DIR
_
_
_
_
DIR
_
X (A1) 4A
_
DIR
_
_
DIR
_
X (C2) 4A
During filter cycle with P1 (C2) 0A
_
DIR
_
_
2 * 2 hours with P1
_
_
DIR
During filter cycle (C2) 1A
_
2 * 6 hours (with CP)
_
During filter cycle (C2) 1A During filter cycle (C2) 1A
1SP (A4) 8A 1SP (A4) 8A 1SP (A4) 8A 1SP (A4) 8A 1SP (A4) 8A 1SP (A4) 8A 1SP (A4) 8A
1SP (A1) 8A 1SP (A1) 8A 1SP (A1) 8A
_
_
_
_
DIR
_
_
_
X (C2) 4A
_
DIR
_
_
_
_
_
DIR
_
_
X (A1) 4A
_
DIR
_
_
_
_
DIR
_
X (A1) 4A
_
_
During filter cycle (C2) 1A During filter cycle (C2) 1A
During filter cycle (C2) 1A During filter cycle (C2) 1A _
_
_
_
X (A4)
DIR
_
_
X (C3) 4A
_
_
X (C3) 4A
_ _
_
_
_
X (C3) 4A
During filter cycle with P1 (A1) 0A
2 * 2 hours with P1 2 * 6 hours (with CP) 2 * 6 hours (with CP) 2 * 2 hours with P1 2 * 2 hours with P1 2 * 6 hours (with CP) 2 * 6 hours (with CP) 2 * 2 hours with P1
2 * 2 hours with P1 2 * 2 hours with P1 2 * 6 hours (with CP) 2 * 6 hours (with CP) 2 * 2 hours with P1
2 * 6 hours (with CP)
DIR
_
_
2 * 2 hours with P1
_
_
_
During filter cycle with P1 (A1) 0A During filter cycle with P1 (A1) 0A During filter cycle with CP (A1) 0A
2 * 6 hours (with CP)
_
_
_
_
2 * 6 hours (with CP)
_
_
_
During filter cycle with P1 (A1) 0A During filter cycle with P1 (A1) 0A During filter cycle with CP (A1) 0A During filter cycle with CP (A1) 0A During filter cycle with P1 (A1) 0A During filter cycle with P1 (A1) 0A During filter cycle with CP (A1) 0A
2 * 6 hours (with CP)
DIR
_
X (A4)
_
2 * 6 hours (with CP)
2 * 2 hours with P1
During filter cycle (A1) 1A
_
_
Circ. Pump (CP) configuration
1SP (A4) 8A 1SP (A4) 8A 1SP (A4) 8A 1SP (A4) 8A
_
_
Light 2 DIRECT 2
DIR
X (A4)
DIR
X (A4)
DIR
_ During filter cycle (C2) 1A During filter cycle (C2) 1A
X (C2)
DIR
_
X (C2)
DIR
_
During filter cycle with P1 (A1) 0A During filter cycle with P1 (A1) 0A During filter cycle with CP (A1) 0A During filter cycle with CP (A1) 0A During filter cycle with P1 (A1) 0A During filter cycle with P1 (A1) 0A
2 * 2 hours with P1 2 * 2 hours with P1 2 * 6 hours (with CP) 2 * 6 hours (with CP) 2 * 2 hours with P1 2 * 2 hours with P1
Heater pump With CP
8A (2KW) With CP 8A (2KW) With CP 8A (2KW) With CP 8A (2KW) With CP 8A (2KW) With CP 8A (2KW) With P1 8A (2kW) With P1 8A (2kW) With CP 8A (2KW) With CP 8A (2KW) With P1 8A (2kW) With P1 8A (2kW) With CP 8A (2KW) With CP 8A (2KW) With P1 8A (2kW) With P1 8A (2kW) With CP 8A (2KW) With P1 8A (2kW) With P1 8A (2kW) With CP 8A (2KW) With CP 8A (2KW) With P1 8A (2kW) With P1 8A (2kW) With CP 8A (2kW) With P1 8A (2kW) With P1 8A (2kW) With CP 8A (2kW) With CP 8A (2kW) With P1 8A (2kW) With P1 8A (2kW)
When the Ozonator is not controlled by a relay, it can be tied to Pump 1 Low speed or Circ. Pump. Pump using cable splitter AMP PN: 9920-401369.
Glossary P1 CP X 1SP 2SP (OUT, AMP, Relay, Tab) 12A, 12A-3A
9919-101500-C
Pump 1 Circulation Pump Installed High speed only High and Low speed Output connector Output current: 1 speed or High - Low speed
Rev. 11-2017
For complete TechBook or more information, see our website: www.geckoalliance.com © Groupe Gecko Alliance Inc., 2017 All trademarks or registered trademarks are the property of their respective owners.
www.geckoalliance.com