Fps xylem rental guide

Rental Guide

Contents

4

General Guide to Pump Selection

5

Guide to Performance Data

6

Pumping Definitions

7 - 14 15 - 20 21

2000/BS Series - Drainers 2600 Range 2000/BS Series/2600 - Electrical Information

22 - 26

3000/C Series - Sewage

27 - 33

3000/N Series - Sewage

34 - 35

Chopper Pumps

36 - 44

Great and Grey – Sewage

45

ATEX Approved Explosion Proof Submersible

46

Telemetry

47

Electrical Equipment

48 - 49 50

Soft Start Control Panels - Specification 3000 Series - Electrical Information

51 - 55

Godwin CD series

56 - 62

Godwin HL series

63 - 65

Godwin NC series

66 - 68

Godwin Heidra series

69 - 70

Solid Handling - Robot Range

71 - 73

Water Treatment

74 - 77

Mixers

78 - 79

Aeration - Radial Aerators

80

Radial Aerators - Oxygen Transfer Rate

81

Aeration - Flyjet and Hydroejectors

82

Pump Flotation Modules

83 - 84 85 86 - 87 88 - 89 90

Hoses and Fittings Friction Loss in Pipe Fittings Chart Weight Reference Guide Conversion Factors Flange Sizes

91 - 93

TotalCare

94 - 95

Birkenburn Reservoir Case Study

96 - 97

Mont Cuet Landfill Site Case Study

99

Contact Details

3

General Guide to Pump Selection

Check:The Electrical Supply available – What Voltage, Single or 3 Phase and the Maximum Amperage. If the Power Supply is inadequate, please ask for details of Generators or consider using a Flygt Prime Assisted Diesel Pump.

Total Head Requirement – The most important calculation to get right! It is the sum of the Total Static Head (the vertical distance from the Suction Strainer to the point of Discharge) plus any Friction Loss allowances. When sizing a pump, the critical thing to determine is the Total Generated Head (TGH) requirement.

Calculation:Static Suction (strainer to the pump) + Static Delivery (from pump to the point of Discharge) + Friction Loss (resistance incurred by liquid when flowing through hoses) = Total Generated Head.

Dirty Water or Solids Handling?

Use Drainer Submersibles (BS Series) and General Purpose Diesels for Dirty Water pumping and where particles are relatively small e.g. sand and gravel.

Use Sewage Submersibles (C/N Series) and Solids Handling Diesels for Sewage pumping and where particles are larger e.g. stones and debris.

The Information contained within this document is for guidance only and is accurate to the best of our knowledge at time of going to print.

4

Guide to Performance Data

The following curves are QH charts showing the performance of the hydraulic unit at constant shaft speeds. Q is represented as litres per second, and total head, H, is in metres.

The data represented in this section is for your guidance only. Detailed information can be obtained from your local Xylem Sales Engineer.

80

Head (m)

BS and D Pumps The curve is the specified performance of the impeller selected. The values shown are for a BS 2125 pump. Impeller characteristics are coded as follows: LT=Low head. MT=Medium head.

HT=High head. SH=Super High Head.

60

Flow (l/s)

C, D, H and N Pumps The power consumption is shown on the chart. The power consumption values for two selected performance duty points are shown by plotted straight lines from the lower to the upper chart. The lower chart and corresponding table provide performance data for different impellers used in a high head 3102 pump.

Additional charts for LT, MT and SH models are shown for each respective pump type.

Head (m)

Flow (l/s)

Impeller No. of Code vanes

Outlet dia. mm Through Motor rpm Available CP vers let, mm rating kW versions

252 254

80 80

1 1

Ă˜52 Ă˜46

4.4 4.4

2850 CP/CS 2850 CP/CS

5

Pumping Definitions

Pumping is the addition of energy to a fluid, which is used mainly for the purpose of moving the fluid from one point to another.

Centrifugal Pumps One which transfers energy to the liquid by means of an impeller; i.e. “a rotating device equipped with suitable vanes”. (The liquid is therefore delivered in a continuous and uninterrupted flow).

Positive Displacement Pumps One which transfers energy to a liquid by means of a reciprocating piston, or similar device, giving an intermittent or “pulsed flow”.

Ejector or Jet Pumps By mixing a high speed drive medium with a low velocity pumped medium, an energy exchange is achieved converting velocity energy into pressure, giving a continuous flow.

Q= Capacity or Volume H= Total Head Total Head= Static Head + Friction loss head.

Static Head The head against which the pump must work when the liquid is stationary.

Friction loss head The head generated by friction of moving liquid, against the walls of the discharge pipes.

P= Pump total pressure in metres.

Net Positive Suction Head (npsh) Energy from an outside source i.e. static head or atmosphere pressure required to ensure liquid enters the pump volute.

Cavitation Cavitation occurs when there is insufficient n.p.s.h. i.e., too low a suction pressure induces cavitation. This causes erosion to the metal surfaces due to the vapour bubble collapsing, allowing the liquid to rush into the subsequent spaces at high velocity, thus creating a water hammer effect.

6

2000 / BS Series - Bibo Drainers

Introduction Flygt Type BS - Pumps are suitable for a very broad field of application. They are used for dewatering on construction sites for houses, streets and roads, tunnels and rock caverns, harbours and dams, for drainage and ballast pumping in shipyards, for drainage in the event of flooding in mines and industrial plants, for cooling, clean water and raw water supply, water spraying, etc.

The Type BS - Pump is of transportable design and requires no installation. All you need to do is to lower it into water and start it. There is a type BS pump suitable for all applications - be it for high capacities, high heads, confined spaces or explosive environments.

The Type BS - Impeller is an open or semi-open channel impeller, made of abrasion resistant high chromium steel and designed specifically for handling media containing highly abrasive materials, such as clay, sand and drilling fines etc.

7

2000 / BS Series Bibo Pumps

Can be installed in a variety of applications

The Type BS - Pump can stand directly on the sump floor

or can be suspended from a rope or chain

The compact design enables Type BS Pumps to be used in confined spaces a 200mm diameter pipe is sufficient for the slimmest pump

The head generated can be increased by connecting two or more Type BS Pumps in series

8

Dimensions

A Pump type

mm

B Opening mm

Strainer

BS2052 BS2066 BS2102 MT HT BS2125 MT HT BS2151 LT MT HT BS2201 Cast Iron MT HT Aluminium MT HT BS2250 MT HT BS2400 MT HT BS2610 BS2620 BS2640 MT HT BS2660 MT HT BS2670 MT HT

530 520

200 385/405/288

5x18 7x21

505 505

390/430 375/390/335

7x40 7x40

710 710

485/515/535 465/390

6x50 6x50

745 745 745

640/655 640/655 570/590

10x42 10x42 10x42

1200 1050

620 430

15x45 10x10

1253 1050

500 430

15x45 10x10

1144 1144

885/912 830

15x45 15x45

1250 1250 570 620

780 680 230 275

10x10 10x10 7 x 16 7 x 16

760 760

375 342

8 x 18 8 x 18

832

430

9 x 18

955 955

500 480

10 x 20 10 x 20

mm

A

B

A

B

9

BS 2052 and BS 2066

BS 2052 Head (m)

A

Flow (l/s)

B Dimensions: A=530mm B=200mm Hose Size: 50mm

Motor 1 kW, 2700 rpm Max. power input 1.4 kW Weight 18kg

BS 2066 Head (m)

A

Flow (l/s)

Motor 2.2 kW, 2800rpm Max. power input 2.8 kW Weight 30kg

10

B Dimensions: A=520mm B=362/375mm Hose Size: 75mm

BS 2102 and BS 2125

BS 2102 MT & HT Head (m)

A

Flow (l/s)

B Dimensions: A=505mm B=MT=395/430mm HT=375/390mm Hose Size: HT 75mm MT 100mm

Motor 3.7 kW/ 5.2 kW, 2850 rpm Max. power input 4.5 kW/6.3kW Weight 50kg

BS 2125 MT & HT Head (m)

A

Flow (l/s)

Motor MT 8.0 kW, 2800 rpm Max. power input 9.5 kW Weight MT 83kg HT 92kg

B Dimensions: A=710mm B=MT 485/515/535mm HT 465mm Hose Size: HT 75mm MT 150mm

11

BS 2151 and BS 2201 MT

BS 2151 MT & HT Head (m)

A

Flow (l/s)

Motor 20 kW, 2900 rpm Max. power input 23 kW Weight 165kg

B Dimensions: A=745mm B=MT 640/655mm MT=570/590mm Hose Size: HT 100mm LT 150mm

BS 2201 MT Head (m)

A

Flow (l/s)

Motor 37 kW, 2920 rpm Max.Power input 41 kW Weight MT Aluminium - 280 kg, Cast Iron - 445kg

12

B Dimensions: A=1253mm B=500mm Hose Size: 200mm

BS 2201 HT and BS 2250

BS 2201 HT Head (m)

A

Flow (l/s)

B Dimensions: A=1050mm B=430mm Hose Size: 100mm

Motor 37 kW, 2920 rpm Max. power input 41 kW Weight HT Aluminium 240 kg Cast Iron 350kg

BS 2250 MT & HT Head (m)

A

Flow (l/s)

Motor 54 kW, 1470 rpm Max. power input 58 kW Weight 540kg

B

Dimensions: A=1100mm B=950mm Hose Size: HT 150mm MT 200mm MT 250mm

13

BS 2400

BS 2400 MT & HT Head (m)

A

B

Flow (l/s)

Motor 90 kW, 2970 rpm Max. power input 97 kW Over temperature protection in stator windings Weight MT 900kg HT 985 kg

14

Dimensions: A=MT 1250mm HT 1251mm B=MT 778mm HT 680mm Hose size: HT=100mm MT=150mm

2600/Range Introduction

Introduction Clearing your worksite of unwanted water is critical to productivity. Flooding means time delays, cost overruns and unsafe working conditions. To get to the bottom of any dewatering job, rely on Flygt 2600 pumps.

Undertaking tough dewatering jobs is what the Flygt 2600 series does best. It ensures that you can get on with the work at hand safely and reliably. All this, thanks to extreme portability, automatic operation, easy maintenance, lasting performance.

The Flygt 2600 series is built to last. Radically engineered from the ground up, these robust dewatering pumps feature innovative hydraulics, durable materials and a practical, ergonomic design. The result is unmatched wear resistance, consistent performance over time.

Flygt 2600 pumps cover low, medium, high and super-high pressures to handle most any application for worksites of every size.

15

2600 Range

BS 2610 MT 110V Single Phase 14

Head (m)

12 10 8 6 4 2 243

0

0

1

2

3

4

5

6

7

8

10

Flow (l/s)

Rated Power 0.85 kW, Weight 21kg

Dimensions: Max. Height=570mm Max. Width=230mm Discharge Ø=2" Strainer Hole: 7x16mm

BS 2610 MT 400V 3 Phase 20

Head (m)

18 16 14 12 10

8 6 4 2 0

234

0

2

4

Rated Power 1.2 kW, Weight 21kg

16

6

8

10

12

14

Flow (l/s)

Dimensions: Max. Height=570mm Max. Width=230mm Discharge Ø=2" Strainer Hole: 7x16mm

2600 Range

BS 2620 MT 24

Head (m)

20 16 12 8 4 0

226

0

2

4

6

8

10

12

14

15

Flow (l/s)

Rated Power 2.2 kW, Weight 32kg

Dimensions: Max. Height=620mm Max. Width=275mm Discharge Ø=3" Strainer Hole: 7x16mm

BS 2640 MT 30

Head (m)

25 20 15 10 5 0

226

0

5

10

15

Rated Power 5.6 kW, Weight 51kg

20

25

30

35

40

Flow (l/s)

Dimensions: Max. Height=760mm Max. Width=375mm Discharge Ø=4" Strainer Hole: 8x18mm

17

2600 Range

BS 2640 HT 50

Head (m)

45 40 35 30 25 20 15 10

257

5 0

0

4

8

12

16

20

24

Flow (l/s)

Rated Power 5.6 kW, Weight 51kg

Dimensions: Max. Height=760mm Max. Width=342mm Discharge Ø=3" Strainer Hole: 8x18mm

BS 2660 MT 40

Head (m)

35 30 25 20 15 10 226

5 0

0

10

20

Rated Power 10 kW, Weight 78kg

18

30

40

50

60

Flow (l/s)

Dimensions: Max. Height=832mm Max. Width=430mm Discharge Ø=6" Strainer Hole: 9x18mm

2600 Range

BS 2660 HT Head (m)

70 60 50 40 30 20 10

251

0

0

5

10

15

20

25

30

35

Flow (l/s)

Rated Power 10 kW, Weight 78kg

Dimensions: Max. Height=832mm Max. Width=430mm Discharge Ø=4" Strainer Hole: 9x18mm

BS 2670 MT 45

Head (m)

40 35 30 25 20 15 10 5 0

226

0

20

40

Rated Power 18 kW, Weight 141kg

60

80

100

Flow (l/s)

Dimensions: Max. Height=955mm Max. Width=500mm Discharge Ø=6" Strainer Hole: 10x12mm

19

2600 Range

BS 2670 HT 70

Head (m)

60 50 40 30 20 10 0

251

0

5

10

15

Rated Power 18 kW, Weight 141kg

20

20

25

30

35

40

45

50 Dimensions:

Flow (l/s)

Max. Height=955mm Max. Width=480mm Discharge Ă˜=4" Strainer Hole: 10x12mm

2000/BS Series/2600 - Electrical Information

Pump Model

Kw (Shaft Power)

Voltage Phase

FLC Amps

DOL Starting Current AMPS

Starting Method

Minimum Generator in Kva to Start/Run

BS2052

1.0

110

1

14.0

46

CAP

BS2052

1.0

230

1

3.8

17

CAP

5 5

BS2052

1.0

400

3

2.2

9.9

DOL

7.5

BS2066

2.2

400

3

4.5

26

DOL

20

BS2071

3.0

400

3

6.6

43

DOL

30

BS2075

3.7

400

3

7.1

36

DOL

25

BS2075

5.5

400

3

11.0

50

DOL

35

BS2084

7.5

400

3

13.0

78

DOL

55

BS2102

5.2

400

3

10.0

71

DOL

50

BS2125

8.0

400

3

15.0

125

DOL

90

BS2151

20.0

400

3

35.0

281

ATX

100

BS2201

37.0

400

3

65.0

430

ATX

150

BS2250

54.0

400

3

104.0

590

ATX

450

BS2400

90.0

400

3

148.0

1245

ATX

425

BS2610

0.9

110

1

11.0

38

CAP

5

BS2610

1.2

400

3

2.7

12

DOL

10

BS2620

2.2

400

3

4.7

27

DOL

20

BS2640

5.6

400

3

11.0

48

DOL

35

BS2660

10.0

400

3

19.0

107

DOL

75

BS2670

18.0

400

3

32.0

213

DOL

150

When two pumps are driven by the same generator, the rating required is 1.5 times that indicated for a single pump Some form of time lag should be connected to prevent both pumps from starting simultaneously, unless the generator has been selected for pumps to start simultaneously.

The Information contained within this document is for guidance only and is accurate to the best of our knowledge at time of going to print.

21

3000 / C Series - Sewage

Introduction This series of pumps covers an extensive performance range and can be used in a variety of applications: from pumping sewage in treatment plants and municipal applications to irrigation, industrial effluent, process water and raw water handling to applications in aquaculture and agriculture.

An extensive range of hydraulic sections, i.e. impellers and volutes, are available to handle the different types of media.

Built-in cooling system on all pumps rated above 9kW. Vanes are at the top of the pump impeller circulate cooling water through a narrow slot around the stator housing.

Channel Impeller C - Pumps are equipped with a shrouded, single or multi-vane impeller that runs in a volute. The shape and size of the impeller is designed to minimise clogging, which makes this pump ideal for wastewater applications.

Nevaclog® The Nevaclog® impeller is designed specially for smaller C - Pumps. Nevaclog® has excellent flow passing properties, because all the parts that might cause clogging when water is flowing at low speed through the impeller channel have been eliminated. This, coupled with the volute’s design is what enables wastewater to flow freely.

22

3000 / C Series - Sewage

C - Pumps

Pump type CS3085 MT CS3085 HT CS3085 LT 1 CS3085 LT 2 CS3102 LT/150 CS3102 LT/100 MT HT CS3127 LT MT/150 MT/100 HT (curve 480-485) HT (curve 250-259) HS CS3152 LT CS3152 MT CS3152 HT/100 CS3152 HT/150 HS3152 CS3201 LT CS3201 MT CS3201 HT HS3201 CS3300 LT CS3300 MT CS3300 HT/200 CS3300 HT/150 FS3085 FS3102 FS3127 FS3152 LT FS3152 HT NS3301

A

B

C

øD

480 450 638 638 720 640 640 640 870 780 700 700 700 550 1150 900 773 845 845 1417 1150 1050 1050 1675 1624 1494 1443 605 660 750 735 710 1438

603 512 660 655 718 718 703 698 776 761 761 722 714 741 1327 1228 1190 1190 1190 1598 1442 1453 1453 1920 1915 1827 1827 535 619 693 1055 1035 1680

350 320 380 400 400 400 383 340 439 430 406 407 380 403 576 530 530 530 490 1000 576 576 576 1000 1000 1000 1000 317 315 415 465 440 1000

75 75 100 100 150 100 100 100 200 150 100 100 80 100 250 200 100 150 150 250 200 150 150 250 200 200 150 100 100 100 100 100 250

øD B

A

C

B

A

C

23

C 3085 MT and C 3102 MT/HT

C 3085 MT 12

Head (m)

30

10

25

8

20

6

15

4

10

2

5

0

0

5

10

15

20

25

30 35 Flow (l/s)

0

Head (m)

0

4

8

Discharge size: 75mm Height: 655mm Motor rating: 2.0kW

12

16 18 Flow (l/s)

Weight: 71kg Maximum width: 638mm

Impeller Code

No. of vanes

Outlet dia. mm CP vers

Through let, mm

Motor rating kW

rpm

Available versions

432 252

1 1

100 80

Ø76 Ø40

2.0 2.4

1400 2840

CP/CS CP/CS

C 3102 MT/HT 16

Head (m)

30

14

25

12 10

20

8

15

6

10

4

5

2 0

Head (m)

0

10

20

30 40 Flow (l/s)

0

0

5

10

15

Discharge size: 75mm/100mm Height: 718mm Motor rating: 3.1kW

20

25

30 35 Flow (l/s)

Weight: 116kg Maximum width: 640mm

Impeller Code

No. of vanes

Outlet dia. mm CP vers

Through let, mm

Motor rating kW

rpm

Available versions

430 252

1 1

100 80

Ø76 Ø52

3.1 4.4

1400 2850

CP/CS/MT CP/CS/MT

24

C 3127 and C 3152

C 3127 40

Head (m)

24

35

20

30

16

25 20

12

15

8

10

4

5 0

Head (m)

0

10

20

30

40

50 60 Flow (l/s)

0

0

20

40

Discharge size: 100/150mm Height: 761mm Motor rating: 5.9/7.4kW

60

80 Flow (l/s)

Weight: 175kg Maximum width: 780mm

Impeller Code

No. of vanes

Outlet dia. mm CP vers

Through let, mm

Motor rating kW

rpm

Available versions

430 250 HT

1 1

100/150 80

100x110 Ă˜58

5.9 7.4

1450 2900

CP/CS CP/CS

C 3152 10

Head (m)

35

8

25

6

20 15

4

10

2 0

Head (m)

30

5 0

50

100

150

200

250 300 Flow (l/s)

0

0

Discharge size: 150/200mm Height: 1228mm Motor rating: 13.5kW

20

40

60

80

100 120 Flow (l/s)

Weight: 426kg Maximum width: 900mm

Impeller Code

No. of vanes

Outlet dia. mm CP vers

Through let, mm

Motor rating kW

rpm

Available versions

616 430 452 HT 265 SH

2 1 1 1

250 250 150 100

102x102 100x115 76x76 40x40

8.8 13.5 13.5 150

950 1450 1450 2920

CP/CT/CS CP/CT/CS CP/CT/CS CP/CT/CS

25

C 3201 and C 3300

C 3201 35

Head (m)

50 40

25

35 30

20

25

15

20 15

10

10

5 0

Head (m)

45

30

5 0

40

80

120

160

0

200 240 Flow (l/s)

0

20

40

60

Discharge size: 200/250mm Height: 1442mm Motor rating: 30/22kW

80

100 120 140 Flow (l/s)

Weight: 588kg Maximum width: 1150mm

Impeller Code

No. of vanes

Outlet dia. mm CP vers

Through let, mm

Motor rating kW

rpm

Available versions

630 456

1 1

200 150

144x120 Ø100

22 30

965 1250

CP/CT/CS CP/CT/CS

C 3300 35

Head (m) MT & HT

30

70 60

25

50

20

40

15

30

10

20

5 0

Head (m)

10 0

100

200

300

400

500 600 Flow (l/s)

0

0

20

Discharge size: 200/250mm Height: 1915mm Motor rating: 54/44kW

40

60

80 100 120 140 160 Flow (l/s)

Weight: 1218kg Maximum width: 1624mm

Impeller Code

No. of vanes

Outlet dia. mm CP vers

Through let, mm

Motor rating kW

rpm

Available versions

632 452 620

1 1 3

250 150 300

Ø190 90x96 Ø102

44 54 44

970 1450 975

CP/CT/CS CP/CT/CS CP/CT/CS

26

3000/N Series - Sewage

N Pump Technology Sustained high efficiency for wastewater handling With its unique semi-open, self-cleaning impeller, the N-pump series can handle fluids with high concentrations of fibrous material, whilst still maintaining a high level of pumping efficiency over long duty periods. The special relief groove in the volute reduces the risk of clogging by creating a self-cleaning flow path through the pump.

N Series Pumps N series pumps are available, contact your local Flygt Rental Centre for curve details: N 3085, N 3102, N 3127, N 3153, N 3171, N 3202, N 3301

Adaptive N-impellers

The Adaptive N-hydraulics further improves the self-cleaning characteristics of Ntechnology with unmatched clog-free performance. This is achieved through the unique axial movement of the Adaptive N-impeller.

The Adaptive N-impeller is designed to move axially upwards when needed, allowing the most bulky of rags and toughest of debris to pass through smoothly.

After the debris has passed, the hydraulic pressure returns the impeller to its original position.

The axial movement of this hydraulic reduces stress on the shaft, seals, and bearings, thereby extending their lifespan. Ultimately clog-free performance requires almost none, or at the very most, simple maintenance and servicing. All in all, the Adaptive N-hydraulics is your assurance of highly economical and reliable pumps that give you peace of mind.

27

N 3085 MT and N 3102 MT

N 3085 MT Head (m)

Discharge size: 75mm Height: 655mm Motor rating: 2.0kW Weight: 71kg Maximum width: 450mm

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

Available versions

460

2

80

2.0

1400

NP/NS/NT

N 3102 MT and SH Head (m)

Flow (l/s)

Impeller Code

No. of vanes

461 MT 2 255 SH 2

28

Discharge size: 80mm/100mm Height: 705mm Motor rating: 3.1/4.2kW Weight: 116kg Maximum width: 610mm

Outlet dia. mm NP vers

Motor rating kW

100 80

3.1 4.2

rpm

1440 2890

Available versions

NP/NS NP/NS

N 3127 and N 3153 MT

N 3127 MT and HT Head (m)

Discharge size: 100/150mm Height: 765mm Motor rating: 5.9kW Weight: 170kg Maximum width: 725mm

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

Available versions

437 MT 487 HT

2 2

100/150 100

5.9 5.9

1450 1450

NP/NS/NT NP/NS/NT

N 3153 MT Head (m)

Discharge size: 150mm Height: 1068mm Motor rating: 13.5kW Weight: 252kg Maximum width: 834mm

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NP vers

431 433

2 2

150 150

Motor rating kW 13.5 13.5

rpm 1455 1455

Available versions NP/NT/NS NP/NT/NS

29

N 3153 HT/SH and N 3171 LT/MT/HT

N 3153 HT/SH Head (m)

Flow (l/s)

Discharge size: 80/100mm Height: 1052mm Motor rating: 13.5/15.0kW Weight: 242kg Maximum width: 763mm

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

Available versions

451 HT 272 SH

2 2

100 80/100

13.5 15.0

1455 2910

NP/NT/NS NP/NT/NS

N 3171 LT MT and HT Head (m)

Flow (l/s)

Discharge size: 100/250mm Height: 1299mm Motor rating: 15/22kW Weight: 460kg Maximum width: 1151mm

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

Available versions

611 LT 431 MT 452 HT

2 2 2

250 150 100

15.0 22.0 22.0

965 1460 1460

NP/NS/NT NP/NS/NT NP/NS/NT

30

N 3171 SH and N 3202 LT/MT/HT

N 3171 SH 80

Head (m)

70 60 50 40 30

274

20 10 0

0

10

20

30

40

50

Flow (l/s)

Discharge size: 100mm Height: 1179mm Motor rating: 22kW Weight: 366kg Maximum width: 884mm

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

Available versions

274 LT

2

108

22.0

2925

NP/NS/NT

N 3202 LT MT and HT Head (m)

Flow (l/s)

Discharge size: 150/300mm Height: 1571mm Motor rating: 22/45kW Weight: 900kg Maximum width: 1439mm

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

Available versions

617 LT 433 MT 454 HT

2 2 2

250 200 150

22.0 30.0 45.0

970 1475 45.0

NP/NS/NT NP/NS/NT NP/NS/NT

31

N 3301 LT/MT 55kW

N 3301 LT and MT 55kW Head (m)

Flow (l/s)

Head (m)

Discharge size: 250mm Height NS: 1705mm Motor rating: 55kW Weight: 1110kg Maximum width NS: 1439mm

0

50

100

150

200

250

300

350

400

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

620 LT 630 MT 632 MT

2 2 2

250 250 250

55 55 55

985 985 985

NP/NT/NS/NZ NP/NT/NS/NZ NP/NT/NS/NZ

32

N3301 HT 55kW/70kW

N 3301 HT 55 kW 80

Head (m)

70 60 50 40 30 20 10 0

0

20

40

60

80

100

120

140

160

Flow (l/s)

N 3301 454 HT Impeller 70 kW VFD Curves Head (m)

Discharge size: 150mm Height NS: 1641mm Motor rating: 55/70kW Weight: 920kg Maximum width NS: 1242mm

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

454 454 HT 456 HT 458 HT

2 2 2 2

150 150 150 150

70 55 55 55

1475 1400 1400 1400

NP/NT/NS/NZ NP/NT/NS/NZ NP/NT/NS/NZ NP/NT/NS/NZ

A Selection of impellers are available on request; also Variable Frequency Drive Starters

33

Chopper Pumps

Introduction Chopper pumps with N Impeller Technology Flygt Chopper pumps have the unique patented N Impeller along with a Hard Iron chopper ring which drastically reduces the risk of clogging. Rugged, wear resistant and self cleaning, it cuts through solids without clogging or sacrificing pump efficiency.

The Flygt Chopper pump range brings to an end troublesome and costly clogging with its heavy-duty and highly dependable chopping abilities. By adding the chopper function to the well proven Flygt N-pump, outstanding performance in heavy duty applications has been achieved. This new pump design has undergone extensive testing in the field. The results from these tests show considerably fewer running problems and considerably lower energy consumption.

Typical applications: • Agriculture • Aquaculture • Food processing • Pulp and paper • Harsh wastewater facilities.

N 3127 Chopper MT and HT 14 12 10 8 6

Discharge size: 100/15mm Height NS: 765mm Motor rating: 4.7kW Weight: 170kg Maximum width NS: 725mm

4 2 0

0

10

20

30

40

50

60

70

Flow - [l/s]

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

428 MT

2

100/150

4.7

1455

34

Available versions NP/NS/NT/NZ

Chopper Pumps

N 3153 Chopper MT and HT Head (m)

Discharge size: 100/150mm Height NS: 1068mm Motor rating: 13.5kW Weight: 252kg Maximum width NS: 763mm

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

Available versions

431 MT 451 HT

2 2

150 100

13.5 13.5

1455 1455

NP/NS/NT NP/NS/NT

N 3171 Chopper MT and HT Head (m)

451

Discharge size: 100/150mm Height NS: 1225mm Motor rating: 22.0kW Weight: 362kg Maximum width NS: 884mm

431

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NP vers

Motor rating kW

rpm

Available versions

431 MT 451 HT

2 2

150 100

22.0 22.0

1460 1460

NP/NS/NT NP/NS/NT

25

35

Great and Grey - Sewage

Introduction After revolutionizing the market for small and midrange wastewater pumps, the Flygt N Pumps are now available in the larger units.

• Incorporating the N Pump technology the potential for blockage is substantially reduced • Due to sustained efficiency, energy costs can be cut by up to 50% • Heads of up to 90mts achieved • Flows in excess of 700l/s

Applications • General by-pass over-pumping • Pump replacement • Application proving • Storm water handling • Industrial effluent handling • Irrigation Pumps from 90 to 250kW available to rent in NP/NS/NT and NZ build (see Page 37).

Ex units available on request.

36

N and C Installation Method

Flygt centrifugal pumps are designed to pump wastewater containing solids and fibres in suspension. The pump can also be used for pumping raw water.

Liquid temperature: Liquid density: The pH of the pumped liquid: Depth of immersion:

P

max 40ยบC (105ยบF) max 1100 kg/m3 6 - 11 max 20 m (65 ft)

For pumping in an explosive or flammable environment the pump can be ATEX certified.

S

The Flygt pump is fully submersible, compact and easy to install. It is available in four versions, depending of the type of installation: C/NP: This system with guide bars and discharge connection permits automatic connection of the pump to the discharge line. The pump can be lifted up for inspection without anyone having to enter the sump. The pump works completely or partially submerged under water.

T

C/NS: A transportable pump designed for operating completely or partially submerged in the pump liquid. It is equipped with base stand and hose connection.

C/NT: The pump is installed vertically dry on a base stand and connected directly to the inlet and outlet lines. The submersible design of the pump prevents damage in the event of flooding.

C/NZ: The pump is installed Horizontally dry on a base stand and connected directly to the inlet and outlet lines. The submersible design of the pump prevents damage in the event of flooding.

Z

For other applications, contact your local Flygt Rental Centre for information.

37

N3315 105kW

N3315 105kW 451HT 440mm 100

Head (m) 451HT

80 60

POWER LIMIT

50Hz

40

45Hz 40Hz

20

35Hz

Rated Power: 105kW 0

0

20

40

60

80

100

120

140

160

Flow (l/s)

Weight: 1220kg Dimensions: Max. Height=1992mm Max. Width=1450mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

451HT

3

150

105

1480

NP/NS/NT/NZ

38

N3231 85kW / 105kW

N3231 85kW 480/360mm 60

Head (m)

50 40 30 20

POWER LIMIT

40Hz

35Hz

0

Rated Power: 85kW

50Hz

10

0

50

100

150

200

Weight: 1380kg

45Hz

250

300

350

Flow (l/s)

Dimensions: Max. Height=2060mm Max. Width=1570mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

480-360

3

200

85

1475

NP/NS/NT/NZ

N3231 105kW 480/400mm 70

Head (m)

60 50 40

POWER LIMIT

50Hz

30

45Hz

20

40Hz

0

Rated Power: 105kW

35Hz

10

Weight: 1590kg 0

50

100

150

200

250

300

Flow (l/s)

Dimensions: Max. Height=2060mm Max. Width=1570mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

480-400

3

200

105

1480

NP/NS/NT/NZ

39

N3231 125kW / 170kW

N 3231 125 kW 470/370mm Head (m)

60 50 40 30 20

Discharge size: 200mm 10 0

35Hz

0

50

100

150

200

40Hz

250

45Hz

Height NS: 2185mm

50Hz

300

Motor rating: 125kW

350

Weight: 1760kg

400

Flow (l/s)

Maximum width NS: 1390mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

470-370

3

200

125

1450

NP/NT/NS/NZ

N 3231 170 kW 470/490mm 100

Head (m)

80 POWER LIMIT

60 50Hz

40

45Hz 40Hz

20 0

Rated Power 170kW

35Hz

0

50

100

150

200

250

Weight 1760kg 300

350

Flow (l/s)

Dimensions: Max. Height=2305mm Max. Width=1570mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

470-490

3

200

170

1480

NP/NT/NS/NZ

A Selection of impellers are available on request; also Variable Frequency Drive Starters

40

N3231 170kW / 215kW

N3231 170kW 480/490mm 100

Head (m)

90 80

POWER LIMIT

70 60 50

50Hz

40

45Hz 40Hz

30

35Hz

20

Rated Power 170kW Weight 1760kg

10 0

0

50

100

150

200

250

300

350

400

Flow (l/s)

Dimensions: Max. Height=2305mm Max. Width=1570mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

480-490

3

200

170

1480

NP/NS/NT/NZ

N3231 215kW 480/490mm 110

Head (m)

100 90 80 70

POWER LIMIT

60 50

50Hz

40

45Hz

30

40Hz

Rated Power 215kW

35Hz

20

Weight 1910kg

10 0

0

50

100

150

200

250

300

350

400

Flow (l/s)

Dimensions: Max. Height=2305mm Max. Width=1570mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

480-490

3

200

215

1485

NP/NS/NT/NZ

41

N3312 100kW / 180kW

N 3312 100 kW 670/450mm Head (m)

40 35 30 25 20 15 10

Rated Power: 100kW

5 0

35Hz

0

100

200

300

400

45Hz

40Hz

500

50Hz

600

Weight: 1975kg 700

Flow (l/s)

Dimensions: Max. Height=2240mm Max. Width=1650mm

N 3312 180 kW 670/545mm 60

Head (m)

50 40 30 20 50Hz 45Hz

10 35Hz

0

0

100

200

300

400

500

600

Rated Power: 180kW Weight: 2275kg

40Hz

700

Flow (l/s)

Dimensions: Max. Height=2975mm Max. Width=1875mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

670-450 670-545

3 3

300 300

100 180

985 990

NP/NT/NS/NZ NP/NT/NS/NZ

A Selection of impellers are available on request; also Variable Frequency Drive Starters

42

N3312 / N3356

N3312 250kW 670/585mm Head (m)

70 60 50 40 30 20

50Hz

10 0

Rated Power: 250kW

45Hz 35Hz

0

100

200

300

400

40Hz

500

Weight: 3125kg

600

700

Flow (l/s)

Dimensions: Max. Height=2975mm Max. Width=1875mm

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

670-585

3

300

250

990

NP/NS/NT/NZ

N3356 90 kW 670/470 40

Head (m) VFD Curves

35 30 25 20

Discharge size: 350mm

15

Height NS: 2400mm

10

Motor rating: 90kW

5 0

35Hz

0

100

200

300

400

40Hz

500

45Hz

50Hz

Weight: 2200kg Max. Width=1875 mm

600

700

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

670-470

3

350

90

985

NP/NT/NS/NZ

43

N3356 / N3400

N3356 100kW 670/475mm 40

Head (m)

35 30 25 20 15

Rated Power: 100kW

10

Weight: 1750kg

5 0

40Hz

35Hz

0

100

200

300

400

500

50Hz

45Hz

600

700

Dimensions: Max. Height=2275mm Max. Width=1900mm

Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

670-475

3

350

100

985

NP/NT/NZ

N3400 250kW 670/575mm 60

Head (m)

50 40 POWER LIMIT

30 20

45Hz

10 0

35Hz

0

100

50Hz

40Hz

Rated Power: 250kW Weight: 3750kg Dimensions: Max. Height=3428mm Max. Width=1900mm

200 300 400 500 600 700 800 900 1000 Flow (l/s)

Impeller Code

No. of vanes

Outlet dia. mm NS vers

Motor rating kW

rpm

Available versions

670-575

3

400

250

990

NP/NT/NZ

44

ATEX Approved Explosion Proof Submersible Pumps

Many of the Flygt range of pumps can be provided certified for use in Zone 1 and Zone 2 hazardous areas.

Pumps are certified: EEx d IIB T4 or EEx d IIB T3 According to the pump model: ATEX category II 2G The pumps are constructed and approved in accordance with: BS EN 50018, BS EN 50019, BS EN 13463-1, BS EN 60079-1, BS EN 60079-7 As appropriate according to the pump model.

For availability of ‘Ex’ units and any other technical assistance contact your nearest Flygt Rental Centre.

• Copies of the relevant ‘Ex’ certification can be made available on request.

• The pumps are maintained in accordance with BS EN 60079 Part 19.

• Before any Flygt ‘Ex’ pump is made available for Rental all parts, flame paths etc; are checked and recorded using regularly calibrated instruments and procedures in accordance with BS EN 60079-19

Explosion Pumps Available: B Pumps

C & N Pumps (ring for confirmation)

Mixers

2201 2400

3085 3102 3127 3153 3171 3202 3301 3231 3312 3356 3400

4620 4630 4640 4650 4660

45

Telemetry

Mobile Telemetry & Alarms Our Rental team is able to call upon the expertise of the Monitoring and Control Division of Xylem Water Solutions UK Ltd, and has many ways of monitoring the overpumping installation, ranging from a simple “pay as you go� GSM alarm unit capable of sending text messages to nominated numbers, to the D716x Dynamic Logic Telemetry Outstation.

Flygt D716x Telemetry Alarm Unit The Flygt D716x is a remote telemetry outstation/alarm unit utilising the mobile telephone network or fixed PSTN telephone line.

This adaptable unit can monitor and be programmed to deliver an SMS text message to a number of mobile phones. The text message content is fully programmable and can uniquely identify the problem or fault. The system is compatible with all the major Telephone networks on 'Contract' or 'Pay As You Go'.

On larger installations for municipal Water Companies, The D716x is capable of connecting directly to an existing Telemetry Master Station.

The D716x Telemetry unit can be powered by different sources depending upon site conditions. It can use alkaline batteries that power the unit for up to 7 years, depending on usage and temperature conditions, or is available in a dc-powered configuration with an internal battery backup of up to 1 year.

46

Electrical Equipment

We specialise in electrical submersible pumps, therefore, it is logical that we are the experts when it comes to the starter and controls that are required for a temporary pumping installation. From a simple single phase starter to a complex multi pump 3 phase control panel, Rental Engineers are available to give advice on all aspects of electromotive power.

Our Rental team carry a comprehensive range of starters, isolators, control equipment, alarm and monitoring devices. Also, sufficient cable to suit day to day usage is stocked both at Nottingham and at all Rental Depot locations. For the larger and more complex installations we are able to select and supply the appropriate extension cables and junction boxes to connect the pump to the control panel.

We can also supply ATEX Certified “Ex� junction boxes and cables glands for use in hazardous areas. If level regulators (floats) are used as the level control we can supply the required I/S protection relays.

Variable Frequency Drives and Soft Start Units Variable Frequency Drives are available to drive pump units from 10.0kW to 200.0kW. The drives provide economical and intelligent pump control and can be configured for running wastewater pumps. With the intelligent VFD you can expect all the advantages of speed regulation, plus top pumping efficiency.

The 10.0kW to 55.0kW drives are IP54 rated and are suitable for use outdoors and do not need an additional weather protective enclosure.

The 200kW drives are available for indoor use or housed in a lockable mobile Motor Control Centre, complete with heating, ventilation, a distribution board is fitted along with internal lighting. 200.0kW is not the ceiling for the supply of VFD control panels, our Rental division have supplied a 400.0kW in its own Mobile MCC. Also available is a range of Soft Start units for the smaller pumps that require simple but efficient motor control.

47

Soft Start Unit - 1.0 - 15kW

Specification: • IP54 Zintex Panel • Rain canopy • Load break door interlocked isolator • Soft starter • Special wide ranging overload unit to protect different size pumps • Earth leakage protection.

• Hand/auto switch.

• Door mounted alphanumeric keypad showing run & trip conditions and also containing – stop/reset-start buttons, Hand or auto LED’s, running LED and flashing tripped LED. • Door mounted emergency stop (also to terminals) • Thermal Switch or Klixon trip circuit • Analogue output related to motor current • Inter-panel interlock system • Lifting hook • Motor & control connections wired to terminals • 12vdc control for floats • 24vdc , 100ma for optional alarm.

• 24vdc , 500ma for optional ultrasonic unit • 24vac power supply customer use

The Heart of the Panel • Designed and manufactured especially for Rental from Xylem • Unique wide ranging overload • Simple kilowatt selection will set up the overload protection • Built in earth leakage • Thermal Switch or Klixon

Digital Display • Kilowatt selected • Running amps • Hand, auto, running and tripped led • Start and stop pushbutton • Last eight fault history

48

Soft Start Unit - 15 - 90kW

Specification : • IP54 free standing panel • Load break door interlocked isolator • Rain canopy • Torq-master 2000 soft starter • Motor output hard wired to 3 x 70mm stud terminals • Main contactor • By-pass contactor • Door mounted keypad (hand control) • 24v ac control system • Float switch control (hard wired) • Emergency stop circuit • Hand/auto selector switch • Remote connection via terminals (auto control) • Standard ‘t’ bar locking system • Lifting bar with hook • Earth leakage protection • Motor Thermal Switch or Klixon hard wired toterminals • Extra relay for telemetry – wired to terminals • Terminals for panel interlocking system • 24vdc , 100ma for optional alarm • 24vdc , 500ma for optional ultrasonic unit

The Heart of the Panel • Soft start unit • Pin locked menu • Adjustable pump range by amps • Adjustable too many starts protection • Float less control • Thermal Switch or Klixon connections • Electronic overload • Under load trip • Electronic shear pin

Information • Motor current • Ambient temperature • RMS Volts • Run hours • Service time indication (for the motor) • Motor status • Printable 1000 event data log

49

3000 Series - Electrical Information

Solid Handling Products

Pump Model 3085 3085 3085 3102 3102 3127 3127 3127 3152 - 4 Pole 3152 - 2 Pole 3153 3153 3153 3153 - 4 Pole 3153 - 2 Pole 3170 3171 3201 3202 3202 3300 3300 3301-6 Pole LT 3301-4 Pole MT 3301 3315 HT 3231 - 4 Pole 3231 - 4 Pole 3231 - 4 Pole 3231 - 4 Pole 3231 - 4 Pole 3312 - 6 Pole 3312 - 6 Pole 3312 - 6 Pole 3356 - 6 Pole 3356 - 6 pole 3400 - 6 Pole

Kw (Shaft Power) 1.3 2.0 2.4 3.1 4.2 4.7 5.9 7.4 13.5 15.0 7.5 9.0 11.0 13.5 15.0 15.0 22.0 30.0 37.0 45.0 44.0 54.0 55.0 55.0 70.0 105.0 85.0 105.0 125.0 170.0 215.0 100.0 180.0 250.0 90.0 100.0 250.0

Voltage Phase 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400

3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3

DOL Starting FLC Current Amps AMPS 3.1 4.5 4.7 6.9 8.3 9.6 12.0 14.0 27.0 28.0 16.0 19.0 24.0 28.0 27.0 31.0 41.0 56.0 66.0 82.0 82.0 100.0 113.0 103.0 132.0 199.0 159.0 200.0 234.0 300.0 395.0 202.0 360.0 465.0 185.0 202.0 465.0

19 19 28 33 72 56 77 114 162 229 91 107 132 150 213 210 248 365 460 605 515 535 660 435 565 1105 710 955 1525 2020 2945 1150 2215 2645 1160 1150 2645

Starting Method

Minimum Generator in Kva to Start/Run

DOL DOL DOL DOL DOL DOL DOL DOL ASD ASD ASD ASD ASD ASD ASD ASD ASD ASD ASD ASD ATX ATX ATX ATX ATX VFD VFD VFD VFD VFD VFD VFD VFD VFD VFD VFD VFD

15 15 20 25 50 40 55 80 40 55 25 25 35 35 50 50 60 85 110 150 150 150 225 150 195 210 170 210 245 315 415 210 375 485 195 210 485

When two pumps are driven from the same generator, the rating required is 1.5 times that indicated for a single pump.

Some form of time lag should be connected to prevent both pumps from starting simultaneously, unless the generator has been selected for multiple pumps to start simultaneously.

The Information contained within this document is for guidance only and is accurate to the best of our knowledge at time of going to print.

50

Godwin In 2010 Xylem acquired Godwin Pumps, bringing with them over 100 years of experience in the design, manufacture, and supply of diesel pumps. Godwin Pumps is renowned for quality, reliability, and long life.

Today, the product range is used throughout the world, in construction, industry, oil refineries, chemical plants, mines, specialist offshore pumping, irrigation and water distribution.

Our Rental division now has access to Godwin’s range of automatic self-priming pumps adding an additional and wider range of Diesel driven Dri - PrimeŽ pumps.

The new Godwin pumps can be skid or trailer mounted for use in mobile applications which can provide exceptional energy efficiency and a significantly reduced clogging capability.

Godwin CD series The Godwin CD range is ideal for high volume, medium head pumping and is capable of handling large solids.

Godwin HL series The Godwin HL range is ideal for medium volume, high head pumping and is also capable of handling large solids-handling.

Godwin CD, HL, Heidra and NC series pumps are now available to rent from Xylem.

All models are available trailer mounted for safe on site transportation or with a skid base. Cast Iron pump end construction, and sound attenuated enclosures.

Godwin CD series

CD80D Dri-Prime速 Hush-Pac The CD80M can handle solids up to 40 mm in diameter. Allows for dry running for prolonged periods while automatically priming and repriming.

This makes it an extremely effective pump, suitable for both slurry, clean water applications as well as small dewatering and bypass applications.

45

Overall dimensions

3000 rpm

40

Length 1621mm

35 2600 rpm

Width 853mm

Head (metres)

30 25

Height 1333mm

2200 rpm

20 15

1800 rpm

10

1400 rpm

5 0

Engine Option Kubota Z482

Minimum capacity limitation

Maximum capacity limitation

0

10

20

30

40

50

60

70

80

90

100 m続/hr

0

2.5

5.5

8.5

12

14 Flow

17

19.5

22.5

25

28

CD80M

l/s

Kubota Z482

Suction connection

80 mm

Wet Weight

725kgs

Delivery connection

80 mm

Impeller diameter

166 mm

Max capacity

65 m続/hr

Max working pressure

4.0 bar

Max Head

15 metres

Max operating speed

2000 rpm

Max Solids

40 mm

Engine

Max Suction Lift

8.5M

52

Kubota Z482

Godwin CD series

CD100M Dri-Prime速 Hush-Pac Able to perform in the toughest conditions, the CD100M can handle solids up to 45 mm in diameter. Allows for dry running for prolonged periods while automatically priming and repriming. This makes it an extremely effective pump, suitable for both slurry, clean water, sewer bypass and general dewatering and many other applications.

40

2200 rpm

Overall dimensions

2000 rpm

Length 1940mm

35 30

Head (metres)

25 20

1800 rpm

Width 1050mm

1600 rpm

Height 1500mm

1400 rpm

15

Engine Option

1200 rpm

10 Minimum capacity limitation

5 0

Perkins 403D-15 Maximum capacity limitation

0

20

40

60

80

100

120

140

160

180

200

220

0

5.5

12

17

22.5

28

33 Flow

39

44.5

50

55.5

62

CD100M

240 m続/hr 66.5 l/s

Perkins 403D-15

Suction connection

100 mm

Wet Weight

1168kgs

Delivery connection

100 mm

Impeller diameter

220 mm

Max capacity

200 m続/hr

Max working pressure

3.8 bar

Max Head

29 metres

Max operating speed

2000 rpm

Max Solids

45 mm

Engine

Max Suction Lift

8.5M

Perkins 403D-15

53

Godwin CD series

CD150M Dri-Prime速 Hush-Pac Able to perform in the toughest conditions, the CD150M can handle solids up to 75 mm in diameter. Allows for dry running for prolonged periods while automatically priming and repriming. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful CD150M has proven itself a pump of choice for contractors, local authorities, industrial and environmental companies.

50

2200 rpm

Overall dimensions

45 2000 rpm

40

Head (metres)

35

Length 2190mm

1800 rpm

Width 1050mm

1600 rpm

Height 1500mm

30 25 20

1400 rpm

15

1200 rpm

10

Engine Options Perkins 404D-22

Minimum capacity limitation

5 0

Perkins 1104D-44TA

Maximum capacity limitation

0

50

100

150

200

250

300

350

400

450

500

550 m続/hr

0

14

28

41.5

55.5

69

83.5 Flow

97

111

125

139

153 l/s

CD150M

Perkins 404D-22

Suction connection

150 mm

Wet Weight

1403kgs

Delivery connection

150 mm

Impeller diameter

260 mm

Max capacity

329 m続/hr

Max working pressure

4.8 bar

Max Head

19 metres

Max operating speed

1500 rpm

Max Solids

75 mm

Engine

Max Suction Lift

8.5M

54

Perkins 404D-22

Godwin CD series

CD300M Dri-Prime速 Hush-Pac The CD300M can handle solids up to 95 mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful CD300M has proven itself a pump of choice for mines, quarries and many other high capacity applications.

70

Overall dimensions

1800 rpm

60

Length 4850mm

1700 rpm

50

1600 rpm

Width 2065mm

Head (metres)

1500 rpm

40

Height 2545mm

1400 rpm 1300 rpm

30 Minimum capacity limitation

20

Engine Options

0

Perkins 1106D-E66TA

Maximum capacity limitation

10

Caterpillar C9 0

100

200

300

400

500

600

0

28

55.5

83.5

111

139

166.5

700

800

900

1000

1100

1200

1300

1400

m続/hr

194

222

250

278

305.5

333

361

388

l/s

Flow

CD300M

Caterpillar C9

Suction connection

300 mm

Wet Weight

6620kgs

Delivery connection

300mm

Impeller diameter

362 mm

Max capacity

1380m続/hr

Max working pressure

6.0 bar

Max Head

54 metres

Max operating speed

1800 rpm

Max Solids

95 mm

Engine

Max Suction Lift

8.5M

Caterpillar C9

55

Godwin HL series

HL80M Dri-Prime速 Hush-Pac The HL80M can handle solids up to 25 mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful HL80M has proven itself a pump of choice for sewage handling, dewatering, local authority usage and many other applications.

112 104

Overall dimensions

2400 rpm

96 88

Length 2190mm

2200 rpm

80

Head (metres)

72

Width 1050mm

2000 rpm

64

Height 1500mm

1800 rpm

56 48

1600 rpm

40

Engine Options

1400 rpm

32

Minimum capacity limitation

24 16 8 0

Perkins 404D-22T

Maximum capacity limitation

Perkins 1104D-44T

0

10

20

30

40

50

60

70

80

90

100

110 m続/hr

0

2.5

5.5

8.5

12

14

17

19.5

22.5

25

28

30.5 l/s

Flow

HL80M

Perkins 404D-22T

Suction connection

100 mm

Wet Weight

1450kgs

Delivery connection

80 mm

Impeller diameter

315 mm

Max capacity

80 m続/hr

Max working pressure

10 bar

Max Head

58 metres

Max operating speed

2000 rpm

Max Solids

25 mm

Engine

Max Suction Lift

8.5M

56

Perkins 404D-22T

Godwin HL series

HL80M Dri-Prime速 Hush-Pac The HL80M can handle solids up to 25 mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful HL80M has proven itself a pump of choice for sewage handling, dewatering, local authority usage and many other applications.

112 104

Overall dimensions

2400 rpm

96 88

Length 2890mm

2200 rpm

80

Head (metres)

72

Width 1300mm

2000 rpm

64

Height 1800mm

1800 rpm

56 48

1600 rpm

40

Engine Options

1400 rpm

32

Minimum capacity limitation

24 16 8 0

Perkins 404D-22T

Maximum capacity limitation

Perkins 1104D-44T

0

10

20

30

40

50

60

70

80

90

100

110 m続/hr

0

2.5

5.5

8.5

12

14

17

19.5

22.5

25

28

30.5 l/s

Flow

HL80M

Perkins 1104D-44T

Suction connection

100 mm

Wet Weight

2200kgs

Delivery connection

80 mm

Impeller diameter

325 mm

Max capacity

101 m続/hr

Max working pressure

10 bar

Max Head

68 metres

Max operating speed

2100 rpm

Max Solids

25 mm

Engine

Max Suction Lift

8.5M

Perkins 1104D-44T

57

Godwin HL series

HL125M Dri-Prime速 Hush-Pac The HL125M can handle solids up to 35 mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful HL125M has proven itself a pump of choice for sewer bypass, general dewatering and many other applications.

112

140 104

Overall dimensions

2400 rpm 2400 rpm

96

120 88

2200 rpm

2200 rpm

Length 3350mm

2000rpm rpm 2000

Width 1300mm

80

Head (metres) Head (metres)

100 72 64

80 56

1800 1800rpm rpm

48

1600 rpm

Height 1887mm

1600 rpm

60 40

1400 rpm

32

Engine Options

1400 rpm

40 24

Minimum capacity limitation

Minimum capacity limitation

16

0

0

Perkins 1104D-E44TA

Maximum capacity limitation

8 20

Maximum capacity limitation

Perkins 1106D-E66TA

0

10

20

30

40

50

60

70

80

90

100

110 m続/hr

0

0

2.5

25

5.5

50

8.5

75

12

100

14

125

17

19.5

22.5

25

28

275

30.5 l/s

300

325 m続/hr

0

7

14

21

28

35

76

83

90

HL125M

150

Flow

175

200

225

41.5 48.5 55.5 62.5 Flow

250 69

l/s

Perkins 1106D-E66TA (129)

Suction connection

150 mm

Wet Weight

3200kgs

Delivery connection

100 mm

Impeller diameter

370 mm

Max capacity

275 m続/hr

Max working pressure

6.0 bar

Max Head

115 metres

Max operating speed

2200 rpm

Max Solids

35 mm

Engine

Max Suction Lift

8.5M

58

Perkins 1106D-E66TA

Godwin HL series

HL150M Dri-Prime速 Hush-Pac The HL150M can handle solids up to 35 mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful HL150M has proven itself a pump of choice for contractors, local authorities, industrial and environmental companies.

160

Overall dimensions

2400 rpm

140

2200 rpm

Length 3350mm

2000 rpm

Width 1300mm

1800 rpm

Height 1887mm

120

Head (metres)

100 80

1600 rpm

60

Engine Options

1400 rpm

40

Minimum capacity limitation

Perkins 1104D-E44TA

20

Perkins 1106D-E66TA

Maximum capacity limitation

0 0

50

100

150

200

250

300

350

400 m続/hr

0

14

28

41.5

55.5 Flow

69

83

97

111 l/s

HL150M

Perkins 1106D-E66TA (168)

Suction connection

150 mm

Wet Weight

3400kgs

Delivery connection

150 mm

Impeller diameter

385 mm

Max capacity

350 m続/hr

Max working pressure

14.8 bar

Max Head

125 metres

Max operating speed

2200 rpm

Max Solids

35 mm

Engine

Max Suction Lift

8.5M

Perkins 1106D-E66TA

59

Godwin HL series

HL160M Dri-Prime速 The HL160M can handle solids up to 35 mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful HL160M has proven itself a pump of choice for mines, quarries and many other high capacity applications.

112 200 104

180

2000 rpm 2400 rpm

Overall dimensions

2200 rpm 1800 rpm

Length 3700mm

2000 rpm

Width 1700mm

96

88 160 80

140 Head (metres) Head (metres)

72

1600 rpm

64 120

Height 2200mm

1800 rpm

56

100 48

40 80 32

60

24

16 40

1400 rpm

1600 rpm 1400 rpm

1200 rpm

Engine Options

Minimum capacity Minimum capacity limitation

limitation

limitation

20 0

Volvo TAD951VE

Maximum capacity limitation Maximum capacity

8

0

10

20

30

40

50

60

70

80

90

100

0

2.5

5.5

8.5

100

12

150

14

200

17

19.5

22.5

25

28

28

41.5

55.5

0

0 0

50 14

250

Flow

69

300

83.5

350 97

Caterpillar C15

110 m続/hr

400

30.5 450 l/s500 m続/hr

111

125

139 l/s

Flow

HL160M

Volvo TAD951VE

Suction connection

200 mm

Wet Weight

5944kgs

Delivery connection

150 mm

Impeller diameter

508 mm

Max capacity

486 m続/hr

Max working pressure

19 bar

Max Head

187 metres

Max operating speed

2000 rpm

Max Solids

35 mm

Engine

Max Suction Lift

8.5M

60

Volvo TAD951VE

Godwin HL series

HL160M Dri-Prime速 Hush-Pac The HL160M can handle solids up to 35 mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful HL160M has proven itself a pump of choice for mines, quarries and many other high capacity applications.

200

2000 rpm

Overall dimensions

180 160

Length 4580mm

1800 rpm

Head (metres)

140 120 100 80

1600 rpm

Width 2065mm

1400 rpm

Height 2545mm

1200 rpm

60

Engine Options

Minimum capacity limitation

40 20 0

Volvo TAD951VE

Maximum capacity limitation

Caterpillar C15

0

50

100

150

200

250

300

350

400

450

500 m続/hr

0

14

28

41.5

55.5

69

83.5

97

111

125

139 l/s

Flow

HL160M

Volvo TAD951VE

Suction connection

200 mm

Wet Weight

7000kgs

Delivery connection

150 mm

Impeller diameter

508 mm

Max capacity

486 m続/hr

Max working pressure

19 bar

Max Head

187 metres

Max operating speed

2000 rpm

Max Solids

35 mm

Engine

Max Suction Lift

8.5M

Volvo TAD951VE

61

Godwin HL series

HL250M Dri-Prime速 Hush-Pac The HL250M can handle solids up to 65 mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications.

The powerful HL250M has proven itself a pump of choice for mines, quarries and many other high capacity applications.

112 140 104 130 88

110 80

(metres) HeadHead (metres)

72

2200 rpm

Length 5500mm Width 2700mm

2000 rpm

90

64

1600 rpm

80

Height 2500mm

1800 rpm

56

70

48

1600 rpm

1400 rpm

60

40

1400 rpm

50 32

Engine Options

1200 rpm

40 24

Minimum capacity limitation

30 16

Minimum capacity limitation

20 8

0

Overall dimensions

1800 rpm

100

10 0

2400 rpm

2000 rpm

96 120

0

10

20

30

40

50

60

0

2.5

5.5

8.5

12

14

17

Maximum capacity

70limitation 80 19.5

0

100

200

300

400

500

700

800

0

28

55.5 83.5

111

139 166.5 194 Flow

222

HL250M

Volvo TAD1215VE

Maximum capacity limitation

600

Flow

22.5

90

100

110 m続/hr

25

28

30.5 l/s

Caterpillar C15

900 1000 1100 1200 1300 m続/hr 250

278 305.5 333

361 l/s

Caterpillar C15

Suction connection

300 mm

Wet Weight

9200kgs

Delivery connection

250 mm

Impeller diameter

440 mm

Max capacity

1224 m続/hr

Max working pressure

13 bar

Max Head

119 metres

Max operating speed

2000 rpm

Max Solids

65 mm

Engine

Max Suction Lift

8.5M

62

Caterpillar C15

Godwin NC series

Godwin NC series With two of the world’s market leading pump brands, Flygt and Godwin, now under the Xylem umbrella, we have combined the world’s most reliable portable pumps with the world’s most efficient self-cleaning hydraulics to bring you the most efficient and reliable Godwin pumps ever.

The new range of Godwin NC pumps are not only reliable, they come equipped with the non-clogging, performance of the proven Flygt N-technology.

This breakthrough combination gives you a best-in-class portable pump that delivers sustained hydraulic efficiency to handle tough wastewater pumping applications.

Self-cleaning Flygt N-technology saves costs The high efficiency of Flygt N-technology is sustained over time due to its selfcleaning ability, keeping energy/fuel costs to a minimum.

Without a doubt, no matter what the challenge, you will always have the peace of mind knowing that our Godwin NC Series Dri-Prime® pumps are on the job.

Godwin pumps, now with sustained high efficiency N hydraulics • Self-cleaning reliability • Hydraulic efficiency • Non-stop optimum performance • Long term energy/fuel savings • Optimized operating speed for low energy/fuel consumption • Low downtime • Extended service intervals • Minimum maintenance • Service friendly

63

Godwin NC series

NC100 Dri-Prime速 Features the unique patented Ntechnology with its innovative self-cleaning impeller. Able to perform in the toughest conditions, the NC100 can handle solids up to 35 mm in diameter. This makes it an extremely effective pump, suitable for both sewage and clean water applications. The powerful NC100 has proven itself a pump of choice when pumping stringy material and general dewatering applications.

50

40

2200 rpm

Overall dimensions

2000 rpm

Length 2190mm Width 1050mm

Head (metres)

1800 rpm

30

Height 1500mm

1600 rpm

1400 rpm

20

Engine Options

1200 rpm

Perkins 403D-15

10 Minimum capacity limitation

0

Perkins 404D-22

0

25

50

75

100

125

150

175

200

225

250 m続/hr

0

7

14

21

28

35

41.5

48.5

55.5

62.5

69

l/s

Flow

NC100

Perkins 403D-15

Suction connection

100 mm

Wet Weight

1345kgs

Delivery connection

100 mm

Impeller diameter

256 mm

Max capacity

188 m続/hr

Max working pressure

5.0 bar

Max Head

27 metres

Max operating speed

1800 rpm

Solids Handling

35 mm

Engine

Max Suction Lift

8.5M

64

Perkins 403D-15

Godwin NC series

NC150 Dri-Prime速 Features the unique patented N-technology with its innovative self-cleaning impeller.

Able to perform in the toughest conditions, the NC150 can handle solids up to 42 mm in diameter. This makes it an extremely effective pump, suitable for both sewage and clean water applications. The powerful NC150 has proven itself a pump of choice when pumping stringy material and general dewatering applications.

70 2200 rpm

Overall dimensions

2000 rpm

Length 2190mm

1800 rpm

Width 1050mm

60

Head (metres)

50 40

Height 1500mm

1600 rpm

30 20

1400 rpm

Perkins 404D-22

Minimum capacity limitation

10

0

Engine Options

1200 rpm

0

25

50

75

0

7

14

21

Perkins 1104D-44T 100 125 150 175 200 225 250 275 300 325 350 375 400 425 28

35

41.5 48.5 55.5 62.5

69 76.5 83.5 90

97 104 111 118

m続/hr l/s

Flow

NC150

Perkins 404D-22

Suction connection

150 mm

Wet Weight

1410kgs

Delivery connection

150 mm

Impeller diameter

265 mm

Max capacity

241 m続/hr

Max working pressure

6.0 bar

Max Head

26 metres

Max operating speed

1600 rpm

Solids Handling

42 mm

Engine

Max Suction Lift

8.5M

Perkins 404D-22

65

Godwin Heidra series

Heidra Hydraulic Submersible Hush-Pac When the suction lift is greater 8.5 m, Heidra pumps take over where Dri-Prime pumps leave off. Heidra hydraulic submersibles are basically Dri-Prime pumps that have been engineered to work submerged in the liquid they pump. Tough and reliable, Heidra pumps are designed for general pumping of light slurries and municipal sludges Liquid bath mechanical seal = dry-running and reduced maintenance costs Seals in pumps that often run dry can overheat and fail. Godwin mechanical shaft seals run in a liquid bath, which dissipates heat through the pump casing and allows the pump to run dry. This provides more reliable operation, frees operators from closely monitoring the pumps, while reducing maintenance costs.

Durable pump-end = long lifetime Cast iron, the standard build, offers excellent durability.

Open impeller = versatility and fewer stoppages With their open impeller design, Godwin Heidra pumps handle solids of up to 125mm in diameter, reducing the risk of stoppages. The open impeller also means you can use Godwin pumps in a wide range of applications from water and wastewater, to drilling muds and industrial fluids.

66

Godwin Heidra NC series

Heidra HNC100 - Duetz Power Pack An extremely powerful yet compact pump. Able to perform in the toughest conditions, the Heidra 100NC can handle solids up to 35 mm in diameter. The powerful Heidra 100NC has proven itself a pump of choice when pumping stringy material and general dewatering applications.

Overall dimensions Length

2200mm

Width

1050mm

Height

1845mm

40 2000 rpm (1540 rpm)

35 1800 rpm (1386 rpm)

30 1600 rpm (1232 rpm)

Head (metres)

25

20

1400 rpm (1078 rpm)

15 Minimum capacity limitation

10

5 Maximum capacity limitation

0 0

25

50

75

100

125

150

175

200

225 m3/hr

0

7

14

21

28

35

41.5

48.5

55.5

62.5 l/s

Flow

HNC100

Duetz F4M2011

Delivery

100 mm Bauer

Wet Weight

1500kgs

Inlet

100 mm c/w Strainer

Pump Weight

135kgs

Max capacity

200 m続/hr

Impeller diameter

256 mm

Max Head

35 metres

Max working pressure

4.0 bar

Solids Handling

35 mm

Max operating speed

Suction Lift

No Limit

Engine

2200 rpm Duetz F4M2011

67

Godwin Heidra NC series

Heidra HNC150 - Duetz Power Pack An extremely powerful yet compact pump with flow capabilities to 385 m続/hr and discharge heads to 56 metres.

Able to perform in the toughest conditions, the Heidra 150NC can handle solids up to 42 mm in diameter. The powerful Heidra 150NC has proven itself a pump of choice when pumping stringy material and general dewatering applications.

Overall dimensions Length

2200mm

Width

1050mm

Height

1845mm

35

30

2000 rpm (1540 rpm)

Head (metres)

25

1800 rpm (1386 rpm)

20

1600 rpm (1232 rpm)

15

1400 rpm (1078 rpm)

10

5 Minimum capacity limitation

0

Maximum capacity limitation

0

25

50

75

100

125

150

175

200

225

250

0

7

14

21

28

35

41.5

48.5

55.5

65.5

69

275 m続/hr 76

l/s

Flow

HNC150

Duetz F4M2011

Delivery

150 mm Bauer

Wet Weight

1500kgs

Inlet

150 mm c/w Strainer

Pump Weight

155kgs

Max capacity

225 m続/hr

Impeller diameter

280 mm

Max Head

29 metres

Max working pressure

5.7 bar

Solids Handling

42 mm

Max operating speed

Suction Lift

No Limit

Engine

68

2000 rpm Duetz F4M2011

Solids Handling - Robot Range

Flygt 100VX Robot Heavy duty pump, for pumping raw sewage and slurries. The Vortex Flow design allows solids of up to 80mm to pass through. Ideal for sewer by-pass work and where large solids are in suspension.

30

Head (m)

25

20

15

10

5

0 0

36

72

108

144

180

216

0

10

20

30

40

50

60

252 m続/hr 70

l/s

Flow

100VX 50 m3/h

Connection Size

100mm

Air Handling

Max Capacity

180 m3/h

Operating Speed

1500 rpm

Max Head

19 Metres

Wet Weight

1484 Kg

Suction Lift

9 Metres

Fuel Tank

150 Lts

Max Solids

80mm

Engine

Duetz F2M2011

Fuel consumption 7.2 litres per hour at full speed

69

Solids Handling - Robot Range

Flygt 150VX Robot Silenced, Heavy Duty pump, for pumping Raw Sewage and Slurries. The Vortex Flow design allows solids of up to 100mm to pass through. Ideal for Sewer by-pass work and where large solids are in suspension.

40

Head (m)

36 32 28 24 20 16 12 8 4 0 0

40

80

120

160

200

240

280

320

360

400

m続/hr

0

11

22

33

44.5

55.5

66.5

78

89

100

111

l/s

Flow

150VX 50 m3/h

Connection Size

150mm

Air Handling

Max Capacity

240 m3/h

Operating Speed

1750 rpm

Max Head

32 Metres

Wet Weight

1990 Kg

Suction Lift

8 Metres

Fuel Tank

142 Lts

Max Solids

100mm

Engine

Duetz F4M2011

Fuel consumption 7.2 litres per hour at full speed

70

Water Treatment We can now rent water treatment products from our Sanitaire & Wedeco brands. Our high-tech treatment systems can provide the most cost-effective solutions for our customers without putting an undue burden on the environment.

Wedeco UV technology can be used to disinfect drinking water, wastewater and industrial process water. UV treatment is chemical-free and an environmentally friendly alternative to chlorine disinfection. Our Wedeco systems use rays of UV light to kill dangerous micro-organisms, including bacteria, viruses and yeasts, preventing them from multiplying.

Sanitaire diffuser systems offer higher oxygen transfer efficiency, resulting in lower airflow rates, lower back pressure and reduced cost over long term usage. They are generally employed for biological aeration, pre-discharge aeration and sludge holding odour control.

71

Sanitaire Silver Series II

Sanitaire Silver Series II - Diffuser Grid For a combination of high aeration efficiency and low operating costs, there’s the Sanitaire Silver Series II membrane diffuser – the most widely used fine bubble diffused aeration system available today.

The Sanitaire Silver Series II is well established and time proven in the market. This product is widely utilised in the municipal water industry for standard and low-pressure aeration applications; and our LP (low pressure) membrane is an excellent solution for applications where the back pressure allowed on the blower is already defined, such as a refurbishment.

Xylem can now offer a complete fine bubble aeration system (4m x 2m) with our market leading Sanitaire Silver Series II fine bubble membrane diffusers and a 600m3/hr blower unit.

Description

kW

Voltage

Lift Out S/S Aeration Grid 4m x 2m c/w 72 x 9" Sanitaire Membrane Diffuser Heads 600m3/h Blower Unit 3m x 2m x2m

30

400/3/50

72

Wedeco Spektron

Wedeco Spektron The Wedeco Spektron shines new light on the environmentally friendly process of using UV disinfection for drinking water.

Featuring highly efficient UV lamp technology and advanced flow distribution, the Spektron series suits modern drinking water treatment plants and covers a wide array of applications from domestic water supply and industrial uses to large municipal water plants with a capacity of more than one thousand m3/h per unit.

Xylem now has Wedeco Spektron 400 and 600 UV reactors available to rent together with their own control panel for ease of use and inspection.

The Spektron range can be used in a number of applications where water treatment is needed.

Description Spektron 400 300mm Dia x 2.5m S/S UV Reactor c/w 8 x 330w UV Lamps & Control Panel Spektron 600 350mm Dia x 2.9m S/S UV Reactor c/w 12 x 330w UV Lamps & Control Panel

kW

Voltage

2.9

400/3/50

4.3

400/3/50

73

Mixers

Flygt Submersible Mixers consist of a drive unit and propeller, integrated into a compact unit. The mixer is mounted on a guide bar, to enable it to be raised and lowered, to operate at different depths. It can also be angled upwards or downward and can be swivelled to the sides. Its mixing action can therefore be directed to any point in a lagoon or tank.

This flexibility aided by the large blade propeller, running at relatively low speeds, sets in motion large volumes of sludge and water. The Flygt submersible mixer is at least three times as efficient as a conventional mixer. This is due to the high efficiency hydraulic design and the fact that the motor and propeller are integrated into a lightweight, compact unit. No energy is lost in complicated gearing, support bearings and heavy shafts. Also, the mixer can be run intermittently, thus providing further energy savings.

Compact design The machines are either direct-driven or include a reduction gearbox between the motor and the propeller. However, all models are well integrated into a compact unit. So no energy is lost in long heavy shafts and support bearings.

Circular tanks One mixer is normally sufficient for tank volumes up to 2,000m3. Depending on the characteristics of the liquid and the desired degree of agitation, more than one mixer may be necessary for larger tank volumes.

Rectangular tanks If the length, width and depth dimensions of the tank differ considerably, several mixers may be necessary to ensure good results. Rectangular tanks are often located underground. Since Flygt Mixers are installed from the top, installation in underground tanks is easy.

For specific duties on the range of Flygt Submersible Mixers please contact your local service centre.

74

Mixers in Practice

Homogeneous liquid manure in a couple of hours.

Flygt Submersible Mixers have an important role to play in agriculture, for homogenising liquid manure. Even if the manure is old, with a thick dry crust and all the solids have settled at the bottom of the tank, it will be possible by mixing for the whole tank contents to become homogeneous. This is due to the fact that the mixer can operate at different depths, can be orientated in any direction and will quickly set in motion large volumes of the manure.

Wide field of applications in industry Flygt Submersible Mixers are used for keeping liquids of different viscosities in suspension, for mixing dry solids into liquids, for thickening after sedimenting and decanting, and for transporting liquids,

Good environment in fish farming Whether in netting enclosures in open water or in dammed bays, Flygt submersible mixers will maintain ideal fish farming conditions at a modest cost. The mixer will supply a briskly-flowing current of fresh water with good oxygen contents and an abundance of natural food. At the same time, fish droppings will be removed. The risk of rotting and formation of decay gases is eliminated. By establishing circulation between the bottom and the surface , the mixer also evens out the water temperature, which favours the growth of the fish.

Improving the efficiency in sewage treatment plants Flygt Submersible Mixers have been widely adopted in sewage treatment plants throughout the world. Particularly in thickening, sludge and storm water ponds, in buffer tanks and in the mixing of chemicals and lime into the water, the efficiency and low operating costs of the mixers can be utilised to the greatest possible extent.

Flow creation For low head, high capacity laminar flows the large propeller mixer can be used in lake reservoirs, fish farms as well as process mixing.

75

Mixers

As shown: 4620 1.5 kW mixer fitted on a portable, free standing steelwork - available to rent.

76

650

650

880

880

4650

4660

4670

4680

390

390

4630

4640

2500

2500

4410

4430

A (max) Max Ø mm

Type

675

675

908

908

1027

1027

1372

1372

405

405

636

636

-

-

-

mm

Max Ø mm

-

C

B

721 831 835 985

931 931 1256 1256

469 509

559 559

-

-

mm

mm

-

E

D

264

264

195

195

117

117

-

-

mm

F

1192

992

988

878

614

574

1110

1110

mm

G

177 (390) 218 (481) 363 (800) 482 (1063)

100 100 100 100/150

700 810 816 966

61(134) 64 (141)

50 50

457 497

230(507) 263 (580)

100 100

1010

kg (lbs)

mm

mm

1010

Weights

I

H

Available Mixers

G F

øA øD

H E

øB

ø A MAX

H G

77

Aeration - Radial Aerators

Fields of application The efficient mixing characteristics and the simple design of our Ejectors and Aerators make them suitable for aerating biological ponds, fishfarm ponds, lakes and waterways.

The function of the ejectors The principle on which the Ejector operates is simple and well-known. A drive jet from a Flygt Submersible pump is led into the Ejector. The drive jet flows through a nozzle into the ejector housing, which has a delivery pipe for the medium, e.g. air, which is to be pumped (the secondary flow). A drop in pressure occurs when the drive jet passes through the mixing tube. This partial vacuum automatically entrains the pump medium with the drive jet and the contents of the primary and secondary flows are mixed intensively with each other.

The function of the Radial Aerator Aeration by means of high efficiency mixing.

Air dispersion by the same method as the Ejector is distributed radially within a tank, basin or lagoon, via the series of diffusers mounted around a central turbine impeller. As with the Ejectors, being totally submerged significant advantages arise over other forms of aeration.

Low noise levels.

No sprays or liquid dispersion in the atmosphere.

Installation Installation of these aeration products is straightforward either by bolting to the tank floor or they even will be suspended by their own weight in certain circumstances.

Applications Subject to the tank configuration the ejector or aerator can be selected to: Replace existing aeration equipment during breakdown or maintenance periods. Upgrade existing treatment capacity without major investment.

Increase oxygen levels. Reduce ammonia levels.

78

Dimensions and Weight - Radial Aerators

C A

B

Type

Power

Current

Dimensions (mm) a b c

Weight Kg*

308 310 312 315 320

2.4 4.4 5.9 13.5 22

4.5 8.5 11.0 25.0 42.0

610 660 700 660 800 950 1130 995 1320 1150

75 105 180 295 500

50 50 80 100 150

* Weight includes 10m of cable

79

Radial Aerators - Oxygen Transfer Rate

80

Flyjet and Hydroejector

Utilising the principles of an Ejector; the Flyjet and Hydroejector can be used to resuspend solids which have settled in storage tanks.

They can be used in storm water retention tanks at sewage works; for example. 4� and 6� jet pipes are available.

81

Pump Flotation Modules

The concept Our range of pump flotation modules has been developed to provide a light-weight and cost-effective alternative to the traditional steel pontoon. The flotation modules are prefabricated from light-weight, foam-filled, GRP (Glass fibre Reinforced Polymer) and are available in four sizes.

General applications Pump Flotation Modules can be supplied to suit Flygt 2000 Series / BS dewatering pumps, C/N-series wastewater pumps and slurry pumps.

• Applications include: • Mine dewatering • Tailing dams • Underground dams • Sewage treatment

• Quarries • Aeration ponds • Construction site dewatering • Flooding control

Installation The pump and integral module can be simply installed by use of a central lifting attachment. Once in the water, the module can be towed by boat, if required, and secured in position by anchor or guy ropes. The float module remains visible above the water surface for easy recovery.

Design features: • Compact and lightweight • Stainless steel metal parts • Easily mounted to pumps on site

• Lifting points for easy installation • Easy to transport as an integral unit • Foam filled to prevent sinking

By having the pump floating close to the surface, it increases service life through reduced maintenance since it is no longer working within high solids environment.

PFM550 PFM 550 2201 3140 3152/3153 3170/3171 5100 (<52kW) 5150 (<52kW)

Part Number 691 69 00 * * * * *

* On request

PFM550

82

1400 x 1400 x 540mm 20 kg

Hoses and Fittings

To complement our comprehensive range of pumps, extensive stocks of pipework and hoses are held. Our Rental engineers can supply all your needs from 2â&#x20AC;? hose increasing in size to steel pipes in excess of 450mm.

Also BSP pipe and cast iron fittings to suit most applications including valve, taper, hose spigot, flexible couplings and hose clamps, specialised hoses for high pressure applications are also stocked.

83

Hoses and Fittings

A pump relies on a secure link between the source and the discharge point. Poor hoses will leak, collapse and cause unwanted problems. So, at Xylem we only sell those hoses we use ourselves – “Cheap hose is expensive hose in the long run”.

Specification

Wire-armoured Suction Hose

Bore dia. mm

Outside dia. mm

Working Pressure bars

Weight per 6m incl. cpgs kg

51 76 102 150

63 89 116 169

8 8 8 5

12 26 35 60

A tough hose developed for the construction industry, with a tube of smooth synthetic rubber, covered with weather resistant synthetic rubber, reinforced with cords of synthetic textile and an embedded helix of high-tensile steel wire.

It is flexible and heavy, yet easy enough to manoeuvre.

It seals well onto the pipe fittings, withstands high pressure and is also tough.

It is ideal for suctions and for discharge where the bend must not collapse.

Specification Bore dia. mm in.

PVC Suction and Discharge Hose

50 75 100 150

2 3 4 6

Outside dia. mm

Working Pressure bars

Weight per 6m incl. cpgs kg

58 87 115 167

5 5.5 4.5 3

6 10 25 40

PVC is a high grade hose, flexible, lightweight, with exceptional resistance to abrasion and weathering. The smooth bore offers minimum resistance to flow.

The strengthened PVC helix is embedded in the hose wall for extra strength.

Specification

Polythene Delivery Hose

Bore dia. mm in.

Outside dia. mm in.

50 75 100 150

65 90 115 170

2 3 4 6

2.5 3.5 4.5 6.75

Working Pressure bars psi 6 4 3 3

90 60 50 50

Weight per 6m incl. cpgs kg 8 14 18 43

This is a proven semi-rigid delivery hose, which is well known throughout the industry. It is damage resistant, but also lightweight and simple to handle.

Friction loss is kept to a minimum in this smooth bore hose.

84

Friction Loss in Pipe Fittings Chart

Friction Loss In Smooth Bore Pipe Losses in m/100 or ft./100ft I.G.P.M.2”

3”

4”

6”

50 75 100 150 200 300 400 500 600 700 800 900 1000 1200 1400 1600 1800 2000 2500 3000 4000 5000

10 20 35

1.4 3 5 12 18 40

0.3 0.7 1 2.5 4.5 10 18 28 38

8”

0.1 0.35 0.6 1.2 2.2 3.5 4.5 6.5 8 10 13 18 26 32 36 38

10”

0.4 0.7 1.1 1.5 2 2.7 3.4 4 6 8 11 14 17 25 38

12”

0.35 0.5 0.7 0.8 1 1.4 2 3 4 4.5 5 9 12 21 32

m3/h

0.4 0.5 0.8 1 1.5 2 2.5 4 5 8 13

10 15 20 30 50 75 100 125 150 175 200 225 250 300 350 400 450 500 650 750 1000 1250

m 3/h x 4 = g.p.m. approx The table refers to new pipes and moderate corrosion could increase resistance by 30%. To calculate resistance of Bends and Fittings, an ‘equivalent length’ for each accessory needs to be added to the actual length of pipe. The equivalent length in feet can be estimated by multiplying the factors in the adjacent table by the pipe diameter in inches.

Example :- A 6” Gate Valve is equivalent to 12 ft of extra pipe Mitre elbow or tee Round elbow Slowbend Square edged entrance Gate valve fully open Globe valve fully open Non-return valve (flap type) Foot-valve and strainer (clean)

5 3 2 3 2 10 3 5

85

Weight Reference Guide - Pumps

Submersible Pump Type

BS/NS/CS Weight Inc Base Stand

2052 18Kgs 2066 30Kgs 2102 50Kgs 2125 Aluminium 89Kgs 2125 Cast Iron 180Kgs 2151 165Kgs 2201MT Aluminium 280Kgs 2201MT Cast Iron 445Kgs 2201HT Aluminium 240Kgs 2201HT Cast Iron 350Kgs 2250 540Kgs 2400 985Kgs 2610 MT 21Kgs 2620 MT 32Kgs 2640 MT & HT 51Kgs 2660 MT & HT 78Kgs 2670 MT & HT 141Kgs 3085MT 71Kgs 3102MT 116Kgs 3102SH 114Kgs 3127MT 170Kgs 3127HT 155Kgs 3152LT 426Kgs 3152MT 321Kgs 3152HT 280Kgs 3153 LT 379Kgs 3153MT 252Kgs 3153HT 232Kgs 3153SH 242Kgs 3171LT 460Kgs 3171MT 362Kgs 3171HT 321Kgs 3201MT 588Kgs 3201HT 540Kgs 3202LT 900Kgs 3202MT 610Kgs 3202HT 580Kgs 3300LT 1'175Kgs 3300MT 1'188Kgs 3300HT 988Kgs 3301LT 1'110Kgs 3301MT 1'030Kgs 3301HT 920Kgs 3315HT 1220Kgs

Pump Type

Weight

Large Submersible Pump Range 3231 85Kw 3231 105Kw 3231 125Kw 3231 170Kw 3231 215Kw 3312 100Kw 3312 180Kw 3312 250Kw 3356 100Kw 3400 75Kw 3400 250Kw

1'380Kgs - Pump Only 1'590Kgs - Pump Only 1'530Kgs - Pump Only 1'760Kgs - Pump Only 1'910Kgs - Pump Only 1'975Kgs - Pump Only 2'275Kgs - Pump Only 3'125Kgs - Pump Only 1'750Kgs - Pump Only 2'700Kgs - Pump Only 3'750Kgs - Pump Only

Original Flygt Diesel Range Flygt Swell 100 - Full Fuel Tank Flygt Swell 150 - Full Fuel Tank Flygt ROBOT 100VX - Full Fuel Tank Flygt ROBOT 150VX - Full Fuel Tank Flygt 150WP - Full Fuel Tank Flygt Swell 200 - Full Fuel Tank

1'510Kgs 1'790Kgs 1'484Kgs 1'990Kgs 1'820Kgs 1'750Kgs

Godwin Diesel Range - Skidbase Hushpac CD80D - Kubota Z482 Engine - Wet Weight 725Kgs CD100M - Perkins 403D-15 Engine - Wet Weight 1'168Kgs CD150M - Perkins 404D-22 Engine - Wet Weight 1'403Kgs CD300M - Caterpillar C9 Engine - Wet Weight 6'620Kgs HL80M - Perkins 1104D-44T Engine - Wet Weight 2'200Kgs HL125M - Perkins 1106D-E66TA Engine - Wet Weight3'200Kgs HL150M - Perkins 1106D-E66TA Engine - Wet Weight3'400Kgs HL160M - Volvo TAD 951VE Engine - Wet Weight 7'000Kgs HL250M - Caterpillar C15 Engine - Wet Weight 9'200Kgs NC100 - Perkins 403D-15 Engine - Wet Weight 1'390Kgs NC150 - Perkins 404D-22 Engine - Wet Weight 1'410Kgs Heidra 150 Duetz F4M2011 Power Pack - Wet Weight1'500Kgs HNC100 Pump Only 135Kgs HNC150 Pump Only 155Kgs

Mixers 4620 4630 4640 4650 4660 4670

18Kgs 60Kgs 63Kgs 174Kgs 209Kgs 345Kgs

Panels 15Kw Soft Start 90Kw Soft Start

30Kgs 130Kgs

The weights above DO NOT include Cable, Chains or Hoses The weights contained within this guide are an estimate only and the actual weight of the item to be lifted must be separately assessed and verified The Information contained within this document is for guidance only and is accurate to the best of our knowledge at time of going to print.

86

Kg

Kg

Galvanised pipe 1M Galvanised pipe 2M Galvanised pipe 3M Bauer Ball Connector Bauer Level Closure Ring Bauer Socket Bauer 90 Deg Bend C/W Closure Ring Bauer Equal Tee C/W 2 Closure Rings Bauer Flanged with ball & Closure Ring Bauer Flanged with Socket 3

Steel “Bauer” Type Pipe & Fittings 3 3 7 0.2 0.5 0.1 1 1.5 3 4

2" - 50mm

12 6 8

26

17 12

2" - 50mm

Size

6M PVC Suction & Discharge Hose C/W Bauers 6M Polythene Semi Rgid Hose C/W Bauers 6M Wire Armoured Hose C/W Bauers 3M Wire Armoured Hose C/W Flanges 3M

Gate Valve Metal Wedge NRV Cast Iron Flap Type D/F Bend Short D/F Bend Long Duck Foot Bend Equal Tee Radial Tee “Y” Piece Taper VJFA Cast Iron Pipe Cement lined kg/M NP 16 Flange Hoses Wire Armoured Hose C/W Bauers

Cast Iron Pipe & Fittings

35 25 18

35 21 13 21 19 21 55 20 10 5 20 6

Kg

4" - 100mm

60 40 43

65 37 22 34 33 36 83 36 15 7 30 8

Kg

6" - 150mm

50 95

104 69 34 52 50 54 121 54 22 11 40 10

Kg

5 7 11 0.3 1 0.3 2.5 4 5 5

8 12 16 1 1.5 0.6 5.5 8 8 7

15 20 32 1.5 4 1.2 11 15 14 15

22

20 30 40 2 6 2.5 13

95 125

170 132 55 74 82 87 164 89 33 15 52 15

Kg

127 46 20 66 19

228 187 77 101 116 115

8" - 200mm 10" - 250mm 12" - 300mm

3" - 76mm 41/4" - 108mm 61/4" - 159mm 75/8" - 194mm

26 10 14

23 16 11 16 15 17 34 17 8 4 16 5

Kg

3" - 80mm

Weight Reference Guide - Accessories

The weights contained within this guide are an estimate only and the actual weight of the item to be

lifted must be separately assessed and verified

87

Conversion Factors

Inches

x

25.4

=

mm

x

0.0394

=

Inches

Feet

x

03048

=

m

x

3.281

=

Feet

Yards

x

0.9144

=

m

x

1.0936

=

Yards

Miles

x

1.609

=

km

x

0.6214

=

Miles

Ft2

x

0.0929

=

m2

x

10.764

=

Ft2

Miles2

x

2.59

=

km2

x

0.3861

=

Miles2

In3

x

16387

=

mm3

x

0.000061

=

In3

Ft3

x

0.02832

=

m3

x

35.31

=

Ft3

Gals (Imp)

x

4.546

=

L

x

0.22

=

Gals (Imp)

Gals (Imp)

x

0.004546

=

m3

x

220

=

Gals (Imp)

Gals (US)

x

3.785

=

L

x

0.2642

=

Gals (US)

LBS

x

0.4536

=

kg

x

2.2046

=

LBS

Tons

x

1016

=

kg

x

0.000984

=

Tons

0.2727

=

m3/h

x

3.6667

=

Gal/Min (Imp)

Gal/Min (Imp) x Gal/Min (Imp) x

0.0757

=

L/Sec

x

13.21

=

Gal/Min (Imp)

L/Sec

3.6

=

m3/h

x

0.277

=

L/Sec

x

Gal/Min (Imp) x

1.2

=

USGPM

x

0.833

=

Gal/Min (Imp)

PSI

x

0.06895

=

Bar

x

14.504

=

PSI

PSI

x

0.703 S.G

=

M Liquid x

1.422xS.G

=

PSI

Ft Liquid

x

0.02989xS.G =

Bar

x

33.456 SG =

Ft Liquid

STD. ATM

x

1.01225

=

Bar

x

0.9879

=

STD. ATM

HP

x

0.7457

=

kW

x

1.341

=

HP

88

Conversion Factors

Flow Conversions M3/min

264

1.2

US GPM

60

GPM

GPH CFM

60

Tonne Hr 1000 Kg/hr

1.0 SG

Kg/sec

2.12

L/Sec

= dm 3/5 1000

1000

1000

0.06

dm3/min =L/min

792

13.2 3.6

M3/hr

100xSG 3.6 SG

3.66 219.6

4.4

dm3/hr

1.0

60 16.67

L/HR

M3/Sec

60

L/min

รท

x

Head/Pressure Conversions Mega Pascal MPA

33.9

Ft

Atmosphere

10.34 10 PSI

33.5 SG

3.28

10.211 SG

M

2.31 SG

14.5 14.22

bar

1.42xSG

PSI

1.02 Kg/

100

KN/m2

9.8xSG

9.8xSG

1

k Pa

6.9

x

รท

89

Flange Sizes

Normal Bore

Table

Dia. Flange

P.C.D

Bolt Dia.

No. of Bolts

Flange Thickness Grey Cast Iron

1” 1.25” 1.5” 2” 50mm 2.5”

D&E D&E D E NP16 D

4.50” 4.75” 6.00” 6.00” 165mm 6.50”

3.25” 3.44” 4.50” 4.50” 125mm 5.00”

.50” .50” .625” .625” M16 .625”

4 4 4 4 4 4

.50” .625” .688” .750 20mm .688”

E D&E NP10 NP16 D E

6.50” 7.25” 200 (7.87) 200 (7.87) 8.50” 8.50”

5.00” 5.75” 160 (6.30) 160 (6.30) 7.00” 7.00”

.625” .625” M16 M16 .625” .625”

4 4 8 8 4 8

.750” .750” 21 (.83) 21 (.83) .750” 8.75”

NP10 NP16 D E D E

220 (8.66) 220 (8.66) 10.00” 10.00” 11.00” 11.00”

180 (7.09) 180 (7.09) 8.25” 8.25” 9.25” 9.25”

M16 M16 .625” .625” .625” .750”

8 8 8 8 8 8

22 (.87) 22 (.87) .813” .875” .813” 8.75”

NP10 N16 D E D E

285 (11.22) 285 (11.22) 12.00” 12.00” 13.25” 13.25”

240 (9.49) 240 (9.49) 10.25” 10.25” 11.50” 11.50”

M20 M20 .625” .750” .675” .750”

8 8 8 8 8 8

23 (.91) 23 (.91) .875” 1.00” .875” 1.00”

NP10 NP16 D E D E

340 (12.38) 340 (12.38) 14.50” 14.50” 16.00” 16.00”

295(11.61) 295(11.61) 12.75” 12.75” 14.00” 14.00”

M20 M20 .625” .750” .750” .750”

8 12 8 12 8 12

245 (.96) 245 (.96) .875” 1.00” 1.00” 1.00”

NP10 NP16 D E NP10 NP16

400 (15.75) 400 (15.75) 18.00” 18.00” 455 (17.91) 455 (17.91)

350(13.78) 355 (13.98) 16.00” 1.00” 400 (15.75) 410 (16.14)

M20 M25 .750” .875” M20 M25

12 12 12 12 12 12

26 (1.02) 26 (1.02) 1.00” 1.125” 27.5 (1.08) 27.5 (1.08)

3” 80mm 4”

100mm 5” 6”

150mm 7” 8”

200mm 9” 10”

250mm 12” 300mm

NP10 and NP16 are for cold water pressure of 10 bar and 16 bar and are the current British Standard. They are unnecessarily heavy for most contractors’ pumps.

90

Notes

98

Thainstone Business Park Inverurie Aberdeenshire AB51 5GT Tel 01467 623010 Fax 01467 623011 Email info@filpumps.co.uk www.filpumps.co.uk