Compiled by : FD Architects Forum Gr. Floor , Ashoka apartment Bhawani Singh Road C-scheme , Jaipur -302001 Rajasthan ( INDIA) Ph. 91-0141-2743536 Email: architect@frontdesk.co.in Web : http://www.frontdesk.co.in/forum/
Thermal & Sound Insulation
How Heat Is Transmitted ď Ž Conduction: the transmission of heat from one molecule to another within a material or from one material to another when they are held in direct contact.
Convection: the transfer of heat by another agent, such as air or water. Convection Currents: the flow of air that is created within the space.
Radiation: the transmission of heat through a wave motion, similar to the way light is transmitted.
http://www.frontdesk.co.in/forum/
Thermal Insulation Facts Fibrous materials are generally good
insulators Commercial insulation materials are made of:
Glass fibers Glass foam Mineral fibers Organic fibers Foamed plastic
http://www.frontdesk.co.in/forum/
Characteristics of a
good insulation material:
fireproof insect proof moisture proof resistant to any physical change that would reduce its effectiveness against heat flow
Selection of insulation
is based on:
Initial cost Effectiveness Durability Adaptation of its form to that of the construction and installation methods
http://www.frontdesk.co.in/forum/
Heat Loss Coefficients British Thermal Unit: Btu, the amount of heat needed to raise the
temperature of 1 pound of water to 1 degree Fahrenheit.
Coefficient of Thermal Conductivity: k, the amount of heat, in Btu’s,
transferred in one hour through 1 sq. ft. of a given material that is 1” thick and has a temperature difference between its surfaces of 1 degree Fahrenheit.
Conductance: C, the amount of heat that will flow through the material
in 1 hour / sq. ft. of surface with a 1 degree Fahrenheit of temperature difference.
Resistance: R, the opposite of conductivity or conductance. A good
insulation material will have a high R- value.
Total Heat Transmission: U, represents in Btu / sq. ft. / hour with 1
degree temperature difference for a structure which may consist of several materials or spaces. http://www.frontdesk.co.in/forum/
Common insulating materials, “R” values per inch , advantages and disadvantages Insulating material
“R” value
Advantages
Disadvantages
Polyurethane, board
6.25 Very good R-value, can be used with fibreglass resins
Not always easily available, relatively expensive
Polyurethane, poured (two-part chemical)
7.0
Very good R-value, can be used with fibreglass resins, relative ease of application
Not always easily available, expensive, requires very careful volume calculations
Polystyrene, sheets (smooth) Trade name “Styrofoam”
5.0
Readily available, low Cannot be used with fibreglass cost, reasonable R- resins unless protected, easily value damaged
Polystyrene, foamed in place and expanded moulded beads. Known as Isopor, Polypor, etc.
3.75 to Reasonable RCannot be used with fibreglass 4.0 values, lower cost resins unless protected, easily than smooth surfaced damaged sheets
http://www.frontdesk.co.in/forum/
Common insulating materials, “R” values per inch , advantages and disadvantages Insulating material
“R” value
Advantages
Disadvantages Readily absorbs water or other fluids, loses insulating value when wet
Fibreglass wool batts
3.3
Low cost, ease of installation
Rock wool batts Wood shavings
3.7 2.2
As above As above Readily available, low Absorbs moisture and loses Rcost values when wet, decays
Sawdust
2.44 Readily available, low Absorbs moisture and loses Rcost value when wet, packs down under vibration
Straw
Air space
Readily available, low Absorbs moisture and loses Rcost value when wet, host to insects, etc. 1.0 No cost approx.
Has to be completely sealed to prevent air circulation causing heat infiltration
http://www.frontdesk.co.in/forum/
Spray Polyurethane Foam (SPF) Insulation A two component mixture comes together at the tip of a gun, and forms an expanding foam that is sprayed onto concrete slabs, into wall cavities of an unfinished wall, against the interior side of sheathing, or through holes drilled in sheathing or drywall into the wall cavity of a finished wall.
sometimes also called Foamed-In-Place Insulation http://www.frontdesk.co.in/forum/
Rigid panels/Insulation Rigid panel insulation is made from fibrous materials (fiberglass, rock and slag wool) or from plastic foam. They are sometimes sold in sections designed to fit tightly in standard wall cavities.
http://www.frontdesk.co.in/forum/
Rigid polyurethane / Polyisocyanurate (PUR/PIR) foam Rigid polyurethane foam (PUR/PIR) is a closed-cell plastic. It is used as factory made thermal insulation material in the form of insulation boards or block foam, and in combination with various rigid facings as a constructional material or sandwich panel. Polyurethane in-situ foams are manufactured directly on the building site.
Polyurethane – a versatile material
Rigid polyurethane foam insulation materials (PUR/PIR)
http://www.frontdesk.co.in/forum/
Molded Expanded Polystyrene (MEPS) Extruded Expanded Polystyrene (XEPS) Foam Board Polystyrene pellets are mixed with various chemicals to liquefy them. A blowing agent is then injected into the mixture, forming gas bubbles, which produce a closed-cell material that are then molded into large sheets. Commonly known as beadboard, it has an R-value of about 4 per inch of thickness.
(XEPS) Foam Board Extruded expanded polystyrene insulation is similar to MEPS, but the foaming, thick liquid is forced through a shaping die. http://www.frontdesk.co.in/forum/
Insulated Concrete Forms( ICF) ICFs are hollow, light-weight "stay in place" forms made of two Expanded Polystyrene (EPS) panels which are connected by polypropylene webs. During construction, the forms are stacked to the desired height then filled with concrete making stable, durable and sustainable walls.
http://www.frontdesk.co.in/forum/
Structural insulated panels( SIP) Structural insulated panels (SIPs), also called stressed-skin walls, use the same concept as in foam-core external doors, but extend the concept to the entire house. They can be used for ceilings, floors, walls, and roofs.
The panels usually consist of plywood, OSB, sandwiched around a core of expanded polystyrene, polyurethane, polyisocyanurate, compressed wheat straw, or epoxy. http://www.frontdesk.co.in/forum/
Oriented strand board, ( OSB) Oriented strand board, (OSB) or Sterling board (UK), is an engineered wood product formed by layering strands (flakes) of wood in specific orientations.
http://www.frontdesk.co.in/forum/
Blanket Insulation – made from fibrous materials like mineral wool, wood fiber, cotton fiber or animal hair and manufactured to form a mat with thickness of ½” – 4 “. Some installed with vinyl cardboard or wire mesh and is stapled to sides and edges of studs and joists.
http://www.frontdesk.co.in/forum/
Batt Insulation
Batts are precut, whereas blankets are available in continuous rolls.
http://www.frontdesk.co.in/forum/
Components of Batt and Blanket Insulation Fiberglass is a material made from extremely fine fibers of glass. Made from molten glass, usually with 20% to 30% recycled industrial waste and post-consumer content.
Rock and slag wool. Usually made from rock (basalt, diabase) or iron ore blast furnace slag. Some rock wool contains recycled glass. Nonflammable.
http://www.frontdesk.co.in/forum/
Rock and slag wool
http://www.frontdesk.co.in/forum/
Loose Fill Cellulose is 100% natural and 75-85% of it is made from recycled newsprint. a. Fibrous Type – from mineral wool rock, glass wool, slag wool or vegetable fiber usually of wood fiber.
b. Granular Insulation from expanded minerals like perlite, vermiculite or ground vegetable matter.
http://www.frontdesk.co.in/forum/
Reflective Insulation Consists of 2 layers of 99% aluminum foil laminated to the outsides of 2 sheets of heavy-duty polyethylene air-bubble cushioning.
http://www.frontdesk.co.in/forum/
Corrugated Insulation from paper formed into shapes that produced enclosed air pockets into small regular semi – circular corrugations and covering both sides with sheet of flat paper to give strength and produce the air pockets.
http://www.frontdesk.co.in/forum/
Thermal Insulation: Can be installed in THREE positions: BELOW the deck BETWEEN the deck and the membrane ABOVE the membrane
http://www.frontdesk.co.in/forum/
Flat Roof: Insulation and Membrane Position
A vented air space is mandatory when using batt insulation in a flat roof!! If you use rigid polystyrene insulation (the blue kind), no air space is necessary as it is waterproof. http://www.frontdesk.co.in/forum/
Insulation BETWEEN the Deck and the Membrane: Traditional location for insulation: ď Ž use low density rigid panels to support the loads on the roof membrane without allowing puncture of membrane ď Ž any water vapour trapped in insulation will cause deck to rot so use topside vents to relieve pressure
http://www.frontdesk.co.in/forum/
Insulation ABOVE the Membrane: New concept offering major advantages: membrane protected from extremes of heat and cold, is on the warm side of the insulation membrane protected from UV radiation membrane protected from puncture insulation must be extruded polystryrene foam board which is water resistant and covered with a filter layer to prevent migration of ballast http://www.frontdesk.co.in/forum/
Vapour Retarders for Low Slope Roofs: membrane in a protected membrane roof is
also the vapour/air barrier other types of low slope roofs use two layers of asphalt saturated roofing felt bonded together and to the roof with hot asphalt polyethylene film not used as it melts situated on the warm side of the insulation
http://www.frontdesk.co.in/forum/
Flat Roof: BUR (traditional) vs. Inverted (newer methodology) http://www.frontdesk.co.in/forum/
Sound Insulation (Soundproofing) is any means of reducing the intensity of sound with respect to a specified source and receptor.
Soundproofing affects sound in two different ways: noise reduction and noise absorption.
http://www.frontdesk.co.in/forum/
METHODS of ABSORPTION
Frictional
Flexural http://www.frontdesk.co.in/forum/
Resonating
ACOUSTICAL MATERIALS
General Classifications: Porous Materials Panel or Membrane Absorbers Cavity (Helmholtz) Resonators
http://www.frontdesk.co.in/forum/
POROUS MATERIALS Soft, porous materials are very good sound absorbers. The basic acoustical characteristic of these materials is a cellular network of interlocking pores. Within these pores, incident sound energy is converted into heat. Examples of these include acoustical boards, diffusers, soft plasters, mineral wool, and acoustical blankets, among others.
http://www.frontdesk.co.in/forum/
POROUS MATERIALS
Characteristics: Their sound absorption is more efficient at high, rather than low frequencies. However, their acoustical efficiency improves in the low frequency range with increased thickness and with distance to their solid backing
http://www.frontdesk.co.in/forum/
POROUS MATERIALS
Categories of Commercial Materials: Pre-fabricated Acoustical Units Various types of perforated, fissured, or textured materials constitute typical units in this group Commonly used materials include: Acoustical Boards Acoustic Hangers Geocoustic Tiles Diffusers
http://www.frontdesk.co.in/forum/
ACOUSTICAL BOARDS
These can be installed in several ways: Cemented to a solid backing Nailed or screwed to wood framing Laid in a ceiling suspension system
http://www.frontdesk.co.in/forum/
ACOUSTICAL BOARDS
http://www.frontdesk.co.in/forum/
ACOUSTICAL BOARDS
http://www.frontdesk.co.in/forum/
ACOUSTICAL BOARDS Advantages
Trade catalogs contain detailed specifications Easy installation and maintenance Flexible absorption
Disadvantages Difficult to conceal joints between units Soft structure subject to damage Paint redecoration harmful to absorption http://www.frontdesk.co.in/forum/
ACOUSTIC HANGERS Acoustic Hangers or baffles- a system of fiber-board panels that are wrapped with insulation and are hung freely using wire or rope.
Sample of Acoustic Hangers
http://www.frontdesk.co.in/forum/
ACOUSTIC HANGERS
http://www.frontdesk.co.in/forum/
GEOCOUSTIC TILES and PANELS Geocoustic Tiles- special prefabricated units for random application on walls and ceilings.
http://www.frontdesk.co.in/forum/
GEOCOUSTIC TILES and PANELS
http://www.frontdesk.co.in/forum/
GEOCOUSTIC TILES and PANELS
http://www.frontdesk.co.in/forum/
DIFFUSERS Diffusers- absorptive material that have, irregular surfaces, or angled or curved fronts, so when mounted on a wall or the ceiling they stop parallel wall interference and prevent standing waves.
http://www.frontdesk.co.in/forum/
DIFFUSERS
http://www.frontdesk.co.in/forum/
Acoustical Terms Sound: a vibration or wave motion that can be heard, reaches
the ear through air, the air vibrates back and forth in tiny molecular motions of high and low pressure Decibel: the unit of measurement used to indicate the loudness or intensity of sound; comparable to the “degree” as a measurement of heat or cold Reverberation Sounds: airborne sounds which continue after the actual source has ceased, caused by reflections from floors, walls and ceilings Frequency: rate at which sound energized air molecules vibrate Impact Sounds: sounds that are carried through the building by the vibrations of the structural materials themselves Masking Sounds: normal sounds within habitable rooms which tend to “mask” some of the external sounds entering the room
http://www.frontdesk.co.in/forum/
Acoustical Terms Decibels Reduction: expression used to indicate the sound
insulating properties of a wall or floor panel Sound Transmission Loss: STL, the number of decibels which sound loses when transmitted through a wall or floor Sound Absorption: capacity of a material or object to reduce sound waves by absorbing them, these sounds are otherwise reflected and cause excessive reverberation and build up of intensity within that area Noise Reduction Coefficient: NRC, the sound absorption of acoustical materials is expressed as the average percentage absorption at the four frequencies which are representative of most household noises, these frequencies are 250, 500, 1000, and 2000 cycles/second Sound Transmission Class: STC, single number which represents the minimum performance of a wall or floor at all frequencies, the higher the STC number, the more efficient the wall or floor will be in reducing sound transmission. http://www.frontdesk.co.in/forum/
NRC : Noise Reduction Coefficient The Noise Reduction Coefficient (NRC) is a scalar representation of the amount of sound energy absorbed upon striking a particular surface. An NRC of 0 indicates perfect reflection; an NRC of 1 indicates perfect absorption. In particular, it is the average of four sound absorption coefficients of the particular surface at frequencies of 250 Hz, 500 Hz, 1000 Hz, and 2000 Hz. These frequencies encompass the fundamental frequencies and first few overtones of typical human speech, and, therefore, the NRC provides a decent and simple quantification of how well the particular surface will absorb the human voice. A more broad frequency range should be considered for applications such as music or controlling mechanical noise. Specifications for materials used in sound absorption commonly include an NRC for simplicity, in addition to more detailed frequency vs amplitude charts.
http://www.frontdesk.co.in/forum/
STC – Sound Transmission Class Sound Transmission Class (STC) is an integer rating of how well a building partition attenuates airborne sound. In the USA, it is widely used to rate interior partitions, ceilings/floors, doors, windows and exterior wall configurations The STC number is derived from sound attenuation values tested at sixteen standard frequencies from 125 Hz to 4000 Hz. These transmission-loss values are then plotted on a sound pressure level graph and the resulting curve is compared to a standard reference contour.
http://www.frontdesk.co.in/forum/
DECIBELS
http://www.frontdesk.co.in/forum/
Indian Standards (IS CODE) for INSULATION IS CODE
Title
IS 9742 : 1993
Sprayed mineral wool thermal insulation
IS 9743 : 1990
Thermal insulation finishing cements
IS 10556 : 1983
Code of Practice for Storage and Handling of Thermal Insulation Materials
IS 12432 : Part 1:
1988 Code of practice for application of spray applied insulation Part 1 Mineral fibre
IS 12436 : 1988
Specification for Preformed Rigid Polyurethane (Pur) and Polyisocyanurate (Pir) Foams for Thermal Insulation
IS 13205 : 1991
Code of practice for the application of polyurethane insulation by the in-situ pouring method
IS 14164 : 1994
Industrial application and finishing of thermal insulation material at temperature above - 80째 C and up to 700째 C - Code of practice http://www.frontdesk.co.in/forum/
Thank You for POSTING This forum is for, by and of the architect fraternity and it will only grow by creating New Thread and New Reply, we can also comment in existing threads by clicking following button on upper right corner of forum . Post your expertise valuable comments in forum regularly.
http://www.frontdesk.co.in/forum/