INTRODUCTION
The Blacktown City furniture suite has been developed by HUB Australasia in consultation with Blacktown City Council, to meet the needs of the growing public domain within the Blacktown local government area. The intention of the Blacktown City furniture suite is to better coordinate the deliver y of furniture throughout the city – to have a streamlined look, better ability to manage and maintain our furniture, and to be able to specify furniture to public place developers.
PARK SUITE
The Park Suite gives the parklands of the Blackt wn local g nment a a robust and functional suite of furniture elements. The sui robust and aesthetically pleasing design that me Blacktown City Council. The suite is offered in b a sustainable alternative of ‘Silver Gum’ Modw all outdoor furniture elements across the nume recreational spaces in Blacktown local government a
URBAN SUITE
This unique suite of street furnishings will be located on the streetscapes of the Blacktown local government area over the next 20/25 years. The Urban Suite combines a mode between the seven different elements wi both ‘Spotted Gum’ hardwood and a su Modwood.The Blacktown U inhabits breathing life into the government area.
3 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com
HARD WOO D SPOTTE D G U M M O D WOO D SILVE R G U M
© Copyright HUB Australasia Pty Ltd 1 PARK SUITE BEAUTIFUL, FUNCTIONAL, ROBUST
PARK SEAT
MATERIALS
Linish Aluminium Sand castings
Select grade Hardwood – oil finish or Modwood slats
Stainless steel fasteners
DIMENSIONS: l 1800mm w 600mm h 810mm
OPTIONS: Ar mrests
FOOTING OPTIONS:
Surface or sub-surface mounted
Surface Mount Foot - 9646-851
Fabricated Mount and Nut - 9646-813 / 9646-840
5 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK SUITE
6 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK SEAT GENERAL ASSEMBLY
MATERIALS
Linish Aluminium Sand castings
Select grade Hardwood – oil finish or Modwood slats
Stainless steel fasteners
DIMENSIONS:
l 1800mm w 594mm h 434mm
OPTIONS: Ar mrests
FOOTING OPTIONS:
Surface or sub-surface mounted
Surface Mount Foot - 9646-851
Fabricated Mount and Nut - 9646-813 / 9646-840
7 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK SUITE
PARK BENCH
8 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK BENCH GENERAL ASSEMBLY
PARK PICNIC BENCH
MATERIALS
Linish Aluminium Sand castings
Select grade Hardwood – oil finish or Modwood slats
Stainless steel fasteners
DIMENSIONS:
Standard Bench: l 1800mm w 406mm h 434mm
Accessible Bench: | 930mm w 406mm h 433mm
OPTIONS:
Ar mrests
FOOTING OPTIONS:
Surface or sub-surface mounted
Surface Mount Foot - 9646-851
Fabricated Mount and Nut - 9646-813 / 9646-840
9 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK SUITE
PARK PICNIC TABLE
MATERIALS
Linish Aluminium Sand castings
Select grade Hardwood – oil finish or Modwood slats
Stainless steel fasteners
DIMENSIONS: l 1800mm w 735mm h 790mm
OPTIONS: Ar mrests
FOOTING OPTIONS
Surface or sub-surface mounted
Surface Mount Foot - 9646-851
Fabricated Mount and Nut - 9646-813 / 9646-840
10 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK SUITE
11 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK PICNIC TABLE GENERAL ASSEMBLY
12 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK PICNIC BENCH DISABLED GENERAL ASSEMBLY
PARK BOLL ARD
MATERIALS
Anodised Aluminium
Stainless steel fasteners
Top Cap with Logo
Protective Strip
DIMENSIONS:
l 110mm w 60mm h 900mm
FOOTING OPTIONS:
Surface or sub-surface mounted and removable
Surface Mount Foot - 9646-851
Fabricated Mount and Nut - 9646-813 / 9646-840
13 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK SUITE
14 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK BOLLARD FIXED GENERAL ASSEMBLY
15 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK BOLLARD SUB-SURFACE GENERAL ASSEMBLY
16 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK BOLLARD REMOVEABLE GENERAL ASSEMBLY
PARK BIKE RACK
MATERIALS
Linish Aluminium Sand castings
Stainless steel fasteners
Top Cap with logo
DIMENSIONS: l 100mm w 542mm h 782mm
OPTIONS: Surface or sub-surface mounted
17 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com
PARK SUITE
Picture showing sub-surface mounted
18 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK BIKE RACK SURFACE MOUNTED
19 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK BIKE RACK SURFACE MOUNTED HOT-DIP GALVANISING NOTES: BATH COMPOSITION: MOLTEN CONTAIN NO LESS THAN IF THREADED COMPONENTS FROM THREADS BY A PROCESS THE GALVANISED COATING AS POSSIBLE AND SHALL ROUGHNESS, SHARP POINTS HDG FINISH TO A MINIMUM HDG TO BE IN ACCORDANCE REPAINTING/REPAIR OF 2 COATS OF APPROVED MANUFACTURING DIMENSIONAL WHEN REFERING AUTHORITATIVE. Initial GENERAL HOT-DIP
20 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com SURFACE MOUNT FOOTING OPTIONS S UR F AC E M O UN T FOO T 9646-851 Supplied as standards with orders PICTORIAL VIEW NTS 10 SECTION A-A SHOWING TYPICAL WELDED NUT DETAIL M8 HEX NUT TYP 4 PLACES WELD AROUND NUT ENSURE WELD IS NEAT AND STRONG GENERAL NOTES: REMOVE ALL BURRS AND SHARP EDGES 1. METAL IN THE WORKING AREA OF THE GALVA NISING BATH SHALL BY MASS OF ZINC ARE GALVANISED IN BATCHES, SURPLUS ZINC SHALL BE REMOVED SUCH AS CENTRIFUGING OR BRUSHING SHALL BE CONTINUOUS AND AS SMOOTH AND EV ENLY DISTRIBUTED FREE OF DEFECTS. THE COATING SHALL BE FREE FROM BLISTERS, AND FLUX RESIDUES THICKNESS OF 600g/m^2, AND 85μm WITH AS1214, AS1559, AS4680, AS4791 & A S4792. DAMAGED GALVANISED SURFACES (eg. SITE WELD S) TO BE PAINTED WITH ZINC-RICH PAINT DIMENSIONAL TOLERANCING IN ACCORDANCE WITH HUB TE CHNICAL SPECIFICATION B Registered Design © HUB Innovations Pty Ltd 2018 7 6 F E 6 B A 8 D C A B 1 9646-851 DRG No. PARK SUITE FURNITURE DRAWING TITLE SURFACE MOUNT FOOT BCC FURNITURE SUITE 9646 PROJECT No. DRAWN DATE DRAWN 0.4 kg Default PROJECT TITLE SHEET / MATERIAL GRADE/SPEC FINISH WEIGHT A3 JC PARENT ASSEMBLY 9646-850 APPROVED JH ALL DIMENSIONS IN MILLIMETRES UNODO NOT SCALE SUPPLEMENTARY CAD FILES, DIMENSIONAL DATA SHOW N ON THIS DRAWING IS CONTACT HUB FOR CLARIFICATION OF ANYORCONFLICTING AMBIGUOUS INFORMATION 1 SCALE 1:1 10/04/2018 TOLERANCES ON DIMENSIONS UNO ITP DOC. No. www.hub-group.com LINEAR <= 1000mm:0.5mm LINEAR > 1000mm:1.0mm ANGULAR:0.5 HOT-DIP GALVANISING NOTES: BATH COMPOSITION: MOLTEN METAL IN THE WORKING 1. AREA OF THE GALVANISING BATH SHALL CONTAIN NO LESS THAN 98% BY MASS OF ZINC IF THREADED COMPONENTS ARE GALVANISED IN 2. BATCHES, SURPLUS ZINC SHALL BE REMOVED FROM THREADS BY A PROCESS SUCH AS CENTRIFUGING OR BRUSHING THE GALVANISED COATING SHALL BE CONTINUOUS AND 3. AS SMOOTH AND EVENLY DISTRIBUTED AS POSSIBLE AND SHALL BE FREE OF DEFECTS. THE COATING SHALL BE FREE FROM BLISTERS, ROUGHNESS, SHARP POINTS AND FLUX RESIDUES HDG FINISH TO A MINIMUM THICKNESS OF 600g/m^2, 4. AND 85μm HDG TO BE IN ACCORDANCE WITH AS1214, AS1559, 5. AS4680, AS4791 & AS4792. REPAINTING/REPAIR OF DAMAGED GALVANISED 6. SURFACES (eg. SITE WELDS) TO BE PAINTED WITH 2 COATS OF APPROVED ZINC-RICH PAINT MANUFACTURING DIMENSIONAL TOLERANCING IN 7. ACCORDANCE WITH HUB TECHNICAL SPECIFICATION TIMBER NOTES: ALL TIMBER TO BE KILN DRIED TO A MOISTURE 1. CONTENT OF BETWEEN 10-15% MOISTURE TIMBER TO BE OF 'SELECT' GRADE AND SAP FREE 2. ALL SURFACES TO BE DRESSED IN ACCORDANCE WITH 3. ITP(?) AND AS2796 ALL LENGTHS TO BE FREE OF KNOTS, WARPS, 4. TWISTING, BENDS AND HEART TOLERANCES ON FINISHED TIMBER PARTS TO BE IN 5. ACCORDANCE WITH HUB PART DRAWINGS AND ITP ALL TIMBER TO BE FINISHED AND TREATED PRIOR TO 6. ASSEMBLY WITH OTHER PARTS NOMINATED SURFACE TREATMENT IS APPLICABLE TO 7. ALL SURFACES UNO CROSS GRAIN CUTS TO BE SANDED TO REMOVE 8. BURRED EDGES FINISHED PARTS ARE TO BE FREE OF END SPLINTERING 9. AND IMPERFECTIONS MATERIAL CERTIFICATES OF SUSTAINABILITY FROM 10. FOREST TO MILL MUST BE SUPPLIED WITH ALL TIMBER PRODUCTS MANUFACTURING DIMENSIONAL TOLERANCING IN 11. ACCORDANCE WITH HUB TECHNICAL SPECIFICATION EXTRUSION NOTES: MATERIAL CERTIFICATES TO BE PROVIDED AS PER ITP 1. AND HUB TECHNICAL SPEC. REFER TO CURRENT REVISION DRAWINGS AND CAD FILES 2. FOR EXTRUSION PROFILE ALL EXTRUSION SURFACES TO BE FREE OF DRAW LINES 3. AND TOOL MARKS ALL EXTRUSIONS TO BE STRAIGHT AND TRUE TO WITHIN 4. ALLOWABLE LIMITS AS SET OUT IN ITP EXTRUDED SAMPLES ARE TO BE PROVIDED PRIOR TO 5. COMMENCEMENT OF FULL PRODUCTION RUN MANUFACTURING DIMENSIONAL TOLERANCING IN 6. ACCORDANCE WITH HUB TECHNICAL SPECIFICATION SAND CAST NOTES: MATERIAL CERTIFICATES TO BE PROVIDED AS PER ITP 1. AND HUB TECHNICAL SPEC. CASTINGS TO BE HOMOGENOUS AND WITHOUT 2. CAVITATION CASTINGS TO BE DRESSED AND FETTLED TO REMOVE 3. ALL FLASHING AND RUNNERS CASTINGS SHALL BE FREE OF ALL MOULD AND SAND 4. RESIDUE CASTINGS SHALL BE FREE OF SINKS, WARPS, TWIST, 5. IRREGULARITIES AND COLD SHUTS POST MACHINING TO BE IN ACCORDANCE WITH HUB 6. PART DRAWINGS. MANUFACTURING DIMENSIONAL TOLERANCING IN 7. ACCORDANCE WITH HUB TECHNICAL SPECIFICATION STEEL STEEL FABRICATION NOTES: MATERIAL CERTIFICATES TO BE PROVIDED AS PER ITP 1. AND HUB TECHNICAL SPEC. MANUFACTURING DIMENSIONAL TOLERANCING IN 2. ACCORDANCE WITH HUB TECHNICAL SPECIFICATION ALL WELDING SHALL CONFORM TO AS/NZS1554 (AND 3. WITH SPECIFIED CATEGORY AS NOTED IN ITP/TPS) ALL WELDS SHALL BE FREE OF INCLUSIONS, POROSITY, 4. AND SPLATTER. ALL WELDS TO BE SIZED AS NOTED ON DRAWINGS ALL SURFACES SHALL BE SMOOTH AND CONSISTANT 5. WITHOUT SCRATCHES OR DEFECTS REMOVE ALL BURRS AND SHARP EDGES 6. ALL WELDS WILL BE SUBJECT TO 100% VISUAL 7. EXAMINATION AS A MINIMUM. REFER TO HUB ITP AND TPS FOR FURTHER REQUIREMENTS. REV STRUCTURAL 1. STAINLESS ALL 1. UNDERTAKEN ONLY. FABRICATOR 2. MANUFACTURE FERROUS MATERIALS. BEAD-BLASTING 3. WITHOUT ANODIC 1. 2. 3. DIE-CAST 1. 2. 3. 4. 5. 6. REV NOTES ORIGINAL ISSUE JC JH APVD DRN 10/04/2018 JH INSERT DATE JC INSERT DATE B ORIGINAL ISSUE REVISIONTABLEENTRIES(COPYANDPASTE): Q245 HDG - SEE NOTES JH JC 30/11/2018 NUTSERT CHANGED TO HEX NUT MAT. THK NOW 5mm B PER ASSEMBLY 1x LEFT 1x RIGHT NOTE : HANDED PART 1 PER ASSEMBLY QTY: 17/07/2017 A - - -ALUMINIUM NOTES: 1. Production Finish Architectural Surface. 2. All edges to be deburred and free of sharp protrusions 3. All surfaces to be free from marks and scratches. 4. Maximum extrusion twist tolerance of 2 over total length unless specified. 5. Endcuts to be perpendiclur to main axis unless specified. 6. Anodising 25microns to AS 1231. HDG STEEL FABRICATION NOTES: 1. All splatter and slag to be removed. 2. All edges to be deburred and free of sharp edges and protrusions. 3. All structural welds to AS 1554 4. All galvanised hollow sections to have adequate, ideally hidden ventillation holes. 5. All holes to be re-drilled after galvanising. 6. All tapped holes to be re-tapped after galvanising. 7. All standard sections to be docked at 90 unless stated otherwise. 8. Galvanize in accordance with AS/NZS 4680. 9. Certificates of conformity must accompany any materials STAINLESS STEEL FABRICATION NOTES: 1. Fabrication should only be perform in an area, and with equipment that is not contaminated with Ferrous metal. 2. All edges to be deburred and free of sharp protrusions.. 3. All structural welds to AS 1554 4. All standard sections to be docked at 90 unless stated otherwise. 5. Certificates of conformity must accompany any materials used in the fabrication process. FOUNDATION NOTES: 1. Foundations have been designed for allowable bearing pressure - 150kPa. 2. Foundation material is to be inspected and approved by the geotechnical engineer before casting foundations. 3. Footing to be constructed and backfilled as soon as possible following excavation to avoid softening or drying out by exposure. 4. Constructor is to allow for cost of geotechnical inspection s. 5. Min clearance to existing gas mains to be 300mm. 6. Min clearance to existing water mains to be 150mm. 7. All steel works to be hot dipped galvanised. 8. Foundation location to be accurately marked out by surveyor. CERTIFICATION NOTES (CANOPIES AND SHELTERS): 1. Terrain Category = 2. Maximum additional load at rafter end = 3. Maximum additional wind load = CERTIFICATION NOTES (POLE): 1. Maximum sign area = 2. Terrain Category = 3. Maximum height = 4. Maximum attached load = 5. Maximum attached banner = 6. Certification document reference = ASSEMBLY NOTES: 1. All fasteners to be included in supply of assembly unless otherwise indicated by HUB. 2. All surfaces to be free from marks and scratches. 3. Use a Nickle based anti-seizure lubricant between Stainless fixings and tapped Stainless Steel unless stated. 4. Predrill Wooden slats prior to screwing to avoid splitting FINISH SPECIFICATIONS: 1. Anodising = 25microns to AS 1231. 2. Electro Polishing = Roughness Average of 2 3. Bead Blasting = #6 Round, Lead Free, Soda-Lime Glass unoformly applied to produce a bright even satin finish. Blast material to be free of Ferrous Metals and contaminants. 4. Galvanising = AS/NZS 4680 STEEL FABRICATION NOTES: 1. All edges to be deburred and free of sharp edges and protrusions. 2. All structural welds to AS 1554 3. All standard sections to be docked at 90 unless stated otherwise. 4. Certificates of conformity must accompany any materials used in the fabrication process. PICTORIAL VIEW NTS GENERAL NOTES: REMOVE ALL BURRS AND SHARP EDGES MANUFACTURING DIMENSIONAL TOLERANCES IN ACCORDANCE WITH HUB TECHNICAL SPECIFICATION HOT-DIP GALVANISING NOTES: BATH COMPOSITION: MOLTEN METAL IN THE WORKING AREA OF THE GALVANISING BATH SHALL CONTAIN NO LESS THAN 98% BY MASS OF ZINC THREADED COMPONENTS ARE GALVANISED IN BATCHES, SURPLUS ZINC SHALL BE REMOVED FROM THREADS BY A PROCESS SUCH AS CENTRIFUGING OR BRUSH ING THE GALVANISED COATING SHALL BE CONTINUOUS AND AS SMOOTH AND EV ENLY DISTRIBUTED AS POSSIBLE AND SHALL BE FREE OF DEFECTS. THENGCOATISHALL BE FREE FROM BLISTERS, ROUGHNESS, SHARP POINTS AND FLUX RESIDUES HDG FINISH TO A MINIMUM THICKNESS OF 600g/m^2, AND 85μm HDG TO BE IN ACCORDANCE WITH AS1214, AS1559, AS4680, AS4791 & AS4792. REPAINTING/REPAIR OF DAMAGED GALVANISED SURFACES (eg. SITE WELD S) TO BE PAINTED WITH 2 COATS OF APPROVED ZINC-RICH PAINT MANUFACTURING DIMENSIONAL TOLERANCING IN ACCORDANCE WITH HUB TECHNICAL SPECIFICATION C D 8 A B E 7 JC OPT I O N 1 OPT I O N 2 PER ASSEMBLY 1x LEFT 1x RIGHT NOTE : HANDED PART 1 PER ASSEMBLY QTY: ALUMINIUM NOTES: 1. Production Finish : Architectural Surface. 2. All edges to be deburred and free of sharp protrusions 3. All surfaces to be free from marks and scratches. 4. Maximum extrusion twist tolerance of 2 over total length unless specified. 5. Endcuts to be perpendiclur to main axis unless specified. 6. Anodising 25microns to AS 1231. CERTIFICATION NOTES (CANOPIES AND SHELTERS): 1. Terrain Category = 2. Maximum additional load at rafter end = 3. Maximum additional wind load = CERTIFICATION NOTES (POLE): 1. Maximum sign area = 2. Terrain Category = 3. Maximum height = 4. Maximum attached load = 5. Maximum attached banner = 6. Certification document reference = ASSEMBLY NOTES: 1. All fasteners to be included in supply of assembly unless otherwise indicated by HUB. 2. All surfaces to be free from marks and scratches. 3. Use a Nickle based anti-seizure lubricant between Stainless fixings and tapped Stainless Steel unless stated. 4. Predrill Wooden slats prior to screwing to avoid splitting FINISH SPECIFICATIONS: 1. Anodising = 25microns to AS 1231. 2. Electro Polishing = Roughness Average of 2 3. Bead Blasting = #6 Round, Lead Free, Soda-Lime Glass unoformly applied to produce a bright even satin finish. Blast material to be free of Ferrous Metals and contaminants. 4. Galvanising = AS/NZS 4680 HOT-DIP GALVANISING NOTES: BATH COMPOSITION: MOLTEN METAL IN THE WORKING AREA OF THE GALVANISING 1. BATH SHALL CONTAIN NO LESS THAN 98% BY MASS OF ZINC IF THREADED COMPONENTS ARE GALVANISED IN BATCHES, SURPLUS ZINC SHALL BE 2. GENERAL NOTES: REMOVE ALL BURRS AND SHARP EDGES 1. MANUFACTURING DIMENSIONAL TOLERANCES IN ACCORDANCE WITH HUB 2. TECHNICAL SPECIFICATION PICTORIAL VIEW NTS C D 8 A B 6 7 F ABR I CA TE D FOO T + E MB E DD E D M O UN T & NU T 9646-813 & 9646-840 To be requested on order placement
FASTENER NOTES: STRUCTURAL FASTENERS ARE TO BE SUPPLIED IN ACCORDANCE WITH AS/NZS1252.1/2 STEEL FABRICATION NOTES: STAINLESS STEEL PRODUCTION OPERATIONS TO BE UNDERTAKEN USING STAINLESS STEEL DEDICATED TOOLS FABRICATOR IS TO ENSURE ALL OPERATIONS OF MANUFACTURE AVOID CROSS CONTAMINATION WITH MATERIALS OR TOOLS USED ON FERROUS BEAD-BLASTING STAINLESS STEEL TO USE VIRGIN SHOT FERROUS MATERIAL CONTAMINATION. OXIDATION COATING (ANODISING) NOTES: PARTS ANODIC COATINGS SHALL BE CONTINUOUS, ADHERENT, UNIFORM IN APPEARANCE, AND BE FREE OF POWDERY AREAS (BURNS), LOOSE STAINS, DISCOLOURATIONS, AND DISCONTUNUITIES PITS, BREAKS, AND SCRATCHES, OR OTHER - AS SET OUT IN AS1231-2000. SAMPLING AND INSPECTION OF MANUFACTURED PRODUCTS WILL BE IN ACCORDANCE WITH AS1231 AND AND ITP. SURFACE FINISH GRADE: AS1231-2000:AA-15 WHERE: NOTES: ASSEMBLY 21 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK SUITE
PARK PICNIC SHELTER
22 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com PARK PICNIC SHELTER
BEAUTIFUL, FUNCTION AL, ROBUS T © Copyright HUB Australasia Pty Ltd
2 URBAN SUITE
URBAN SEAT 1800
MATERIALS
Linish Aluminium Sand castings
Select grade Hardwood – oil finish or Modwood slats
Stainless steel fasteners
DIMENSIONS: l 1800mm w 705mm h 812mm
OPTIONS: Surface or sub-surface mounted
24 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN SUITE
25 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN SEAT 1800 GENERAL ASSEMBLY
ÙRBAN SEAT 720
MATERIALS
Linish Aluminium Sand castings
Select grade Hardwood – oil finish or Modwood slats
Stainless steel fasteners
DIMENSIONS: l 720mm w 705mm h 812mm
OPTIONS: Surface or sub-surface mounted
26 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN SUITE
27 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN SEAT 720 GENERAL ASSEMBLY
URBAN BENCH
MATERIALS
Linish Aluminium Sand castings
Select grade Hardwood – oil finish or Modwood slats
Stainless steel fasteners
DIMENSIONS:
l 720mm w 705mm h 812mm
OPTIONS:
Surface or sub-surface mounted
28 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN SUITE
29 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN BENCH GENERAL ASSEMBLY
URBAN BOLL ARD
MATERIALS
Linish Aluminium Sand castings
Stainless steel fasteners
Reflective Strip
DIMENSIONS: l 1050mm w 240mm h 812mm
OPTIONS:
Surface, sub-surface mounted or removable
30 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com
URBAN SUITE
31 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN BOLLARD FIXED SURFACE MOUNTED GENERAL ASSEMBLY
32 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN BOLLARD FIXED SUB-SURFACE MOUNTED GENERAL ASSEMBLY
33 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN BOLLARD REMOVABLE GENERAL ASSEMBLY
URBAN BIKE RACK
MATERIALS
Linish Aluminium Sand castings
Stainless steel fasteners
Reflective Strip
DIMENSIONS:
l 150mm w 250mm h 750mm
OPTIONS:
Surface, sub-surface mounted or removable
34 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN SUITE
35 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN BIKE RACK SUB SURFACE MOUNTED GENERAL ASSEMBLY
36 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN BIKE RACK SURFACE MOUNTED GENERAL ASSEMBLY
BEAUTIFUL, FUNCTION AL, ROBUS T © Copyright HUB Australasia Pty Ltd 3 140LT & 2 40LT BIN
MATERIALS
Chute - Linish Sand Cast aluminium
Roof - Sand Cast aluminium
Body - Mild Steel HDG and powdercoated
CAPACITY: 140Lt & 240Lt Solo Bin
DIMENSIONS:
140Lt - l 800mm w 800mm h 1346mm
240Lt - I 800mm w 800mm h 1438mm
STANDARD COLOUR: Silver RAL 9006 anti -graffiti
38 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com BIN
140LT & 240LT BIN
39 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com BIN 140LT GENERAL ASSEMBLY
40 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com BIN 240LT GENERAL ASSEMBLY
FUNCTION AL, ROBUS T © Copyright HUB Australasia Pty Ltd
BEAUTIFUL,
4 DRINKING FOUNTAIN
DRINKING FOUNTAIN
MATERIALS
Linish Aluminium Sand Cast finish
Bubbler and tap Stainless Steel
DIMENSIONS: l 76mm h 760mm
42 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com DRINKING FOUNTAIN
43 Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com URBAN DRINKING FOUNTAIN GENERAL ASSEMBLY
HUB Australasia Pty Ltd 259 Milperra Road Revesby Sydney, NSW 2212 T +61 2 9212 7144 info@hub-group.com
