Floor boxes & grommets catalogue

026_027_D2010 v3.qxd

1/6/10

12:25

Page 26

Access floor service outlet boxes empty boxes and accessory plates

2 compartment

230

230

mm 230

mm

290

mm

mm

To configure boxes as required, select : 1. Box depth 2. Number of compartments required 3. Desired accessory plates

4 compartment

3 compartment

366

mm

366

75 mm width plates

112 mm width plates

100 mm width plates

Single base – 75 mm depth

CR2001

CR011

CR4001

Single base – 85 mm depth (standard box)

CR2002

CR012

CR4002

Single base – 110 mm depth

CR2003

CR013

CR4003

Separate compartment base – 75 mm depth

CR2004

CR014

CR4004

Separate compartment base – 85 mm depth

CR2005

CR015

CR4005

Separate compartment base – 110 mm depth

CR2006

CR016

CR4006

Empty boxes

Plates

Example

For 2 compartment boxes For 3 compartment boxes For 4 compartment boxes

Blank plate

CR2100

CR020

CR4100

2 gang switched socket outlet

CR2101

CR022

CR4101

2 gang switched socket outlet, low noise / clean earth

CR2102

CR023

CR4102

2 gang unswitched socket outlet

CR2104

CR029

CR4104

3 gang unswitched socket outlet

CR2105

CR030

CR4105

3 gang unswitched socket outlet, low noise / clean earth

CR2116

CR044

CR4118

2 gang RCD socket outlet

CR2112

CR036

CR4111

2 gang RCD socket outlet, low noise / clean earth

CR2115

CR043

CR4117

Punched plate for 2 x 1 gang accessories (60·3 mm fixing centres)

CR2106

CR026

–

Punched plate for 2 gang accessories (120·6 mm fixing centres)

CR2107

CR028

–

Angled punched plate for 4 x RJ45 sockets (37 mm x 22 mm cut-outs)

–

CR042

CR4115

2 x LJ2 accessory plate (50 mm fixing centres)

–

CR031

CR4106

4 x BNC connector plate

CR2109

CR033

CR4108

4 x Data / Telecoms plate (37 mm x 22 mm cut-outs)

CR2113

CR024

CR4112

6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)

CR2114

CR025

CR4113

26

mm

026_027_D2010 v3.qxd

1/6/10

12:26

Page 27

Access floor service outlet boxes pre-wired boxes

4 compartment

3 compartment

Pre-wired service outlet boxes with Electrak tap-offs 230

230

1. Select box depth and desired configuration 2. Select additional accessory plates (if required)

mm

mm 366

mm

366

mm

Includes 1 x twin switched socket outlet

Includes 2 x twin switched socket outlets

Single base – 85 mm depth, pre-wired with 3 m standard tap-off

CR100

CR122

Single base – 85 mm depth, pre-wired with 5 m standard tap-off

CR101

CR123

Single base – 85 mm depth, pre-wired with 3 m low noise / clean earth tap-off

CR110

CR132

Single base – 85 mm depth, pre-wired with 5 m low noise / clean earth tap-off

CR111

CR133

Pre-wired boxes

Additional plates

Example

For 3 compartment boxes For 4 compartment boxes

Blank plate

CR020

CR4100

2 gang switched socket outlet(1)

CR022

CR4101

2 gang switched socket outlet, low noise / clean earth(1)

CR023

CR4102

2 gang unswitched socket outlet(1)

CR029

CR4104

3 gang unswitched socket outlet(1)

CR030

CR4105

3 gang unswitched socket outlet, low noise / clean earth(1)

CR044

CR4118

2 gang RCD socket outlet(1)

CR036

CR4111

2 gang RCD socket outlet, low noise / clean earth(1)

CR043

CR4117

Punched plate for 2 x 1 gang accessories (60·3 mm fixing centres)

CR026

–

Punched plate for 2 gang accessories (120·6 mm fixing centres)

CR028

–

Angled punched plate for 4 x RJ45 sockets (37 mm x 22 mm cut-outs)

CR042

CR4115

2 x LJ2 accessory plate (50 mm fixing centres)

CR031

CR4106

4 x BNC connector plate

CR033

CR4108

4 x Data / Telecoms plate (37 mm x 22 mm cut-outs)

CR024

CR4112

6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)

CR025

CR4113

(1) Additional sockets will require wiring on site

27

028_029P_D2010 v1.qxd

4/6/10

09:55

Page 28

Access floor service outlet boxes 2 and 3 compartment boxes

CR2002 CR100

CR012

Selection chart (p. 26-27) Dimensions and technical information (p. 31) Lid and trim mouldings are precision engineered from hard wearing durable ABS. Lid is reinforced with a Zintec coated mild steel plate Mounting frame and box base - 0·9 mm thick galvanised steel Each compartment has 2 entries for 20 mm and 2 entries for 25 mm flexible conduits Grey mouldings. Alternative colours available to special order. Goosewing grey plates 2, 3 and 4 compartment boxes are also available with separate individual compartment base units for convenient offsite pre-wiring Supplied in parts or fully assembled and configured to customer specification Conform to IEC-61534-22 Pack

Cat. Nos.

1 1 1 1 1 1

CR2001 CR2002 CR2003 CR2004 CR2005 CR2006

1 1 1 1 1

CR2100 CR2101 CR2102 CR2104 CR2105 CR2116

1 1 1

CR2112 CR2115 CR2106

1

CR2107

1 1 1

CR2109 CR2113 CR2114

2 compartment

Pack

Cat. Nos.

3 compartment

Empty boxes

Empty boxes

112 mm compartment widths

100 mm compartment widths

Single base - 75 mm depth Single base - 85 mm depth (standard box) Single base - 110 mm depth Separate compartment base - 75 mm depth Separate compartment base - 85 mm depth Separate compartment base - 110 mm depth

1 1 1 1 1 1

CR011 CR012 CR013 CR014 CR015 CR016

1 1 1 1 1

CR020 CR022 CR023 CR029 CR030 CR044

1 1 1

CR036 CR043 CR026

1

CR028

1

CR042

1 1 1 1

CR031 CR033 CR024 CR025

Accessory plates – 100 mm width

Accessory plates – 112 mm width Blank plate 2 gang switched socket outlet 2 gang switched socket outlet, low noise / clean earth 2 gang unswitched socket outlet 3 gang unswitched socket outlet 3 gang unswitched socket outlet, low noise / clean earth 2 gang RCD socket outlet 2 gang RCD socket outlet, low noise / clean earth Punched plate for 2 x 1 gang accessories (60·3 mm fixing centres) Punched plate for 2 gang accessories (120·6 mm fixing centres) 4 x BNC connector plate 4 x Data / Telecoms plate (37 mm x 22 mm cut-outs) 6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)

Electrak tap-offs (see p. 18-21)

Single base - 75 mm depth Single base - 85 mm depth (standard box) Single base - 110 mm depth Separate compartment base - 75 mm depth Separate compartment base - 85 mm depth Separate compartment base - 110 mm depth Blank plate 2 gang switched socket outlet 2 gang switched socket outlet, low noise / clean earth 2 gang unswitched socket outlet 3 gang unswitched socket outlet 3 gang unswitched socket outlet, low noise / clean earth 2 gang RCD socket outlet 2 gang RCD socket outlet, low noise / clean earth Punched plate for 2 x 1 gang accessories (60·3 mm fixing centres) Punched plate for 2 gang accessories (120·6 mm fixing centres) Angled punched plate for 4 x RJ45 (37 mm x 22 mm cut-outs) 2 x LJ2 accessory plate (50 mm fixing centres) 4 x BNC connector plate 4 x Data / Telecoms plate (37 mm x 22 mm cut-outs) 6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)

3 compartment pre-wired boxes 100 mm compartment widths 1 1 1 1

28

Single base – 85 mm depth, pre-wired with : CR100 2 gang switched socket outlet and 3 m standard tap-off CR101 2 gang switched socket outlet and 5 m standard tap-off CR110 2 gang switched socket (low noise / clean earth) and 3 m low noise / clean earth tap-off CR111 2 gang switched socket (low noise / clean earth) and 5 m low noise / clean earth tap-off

028_029P_D2010 v1.qxd

1/6/10

11:58

Page 29

Access floor service outlet boxes 4 compartment boxes and ancillary items

CR122 CR4002

Selection chart (p. 26-27) Dimensions and technical information (p. 31) Lid and trim mouldings are precision engineered from hard wearing durable ABS. Lid is reinforced with a Zintec coated mild steel plate Mounting frame and box base - 0·9 mm thick galvanised steel Each compartment has 2 entries for 20 mm and 2 entries for 25 mm flexible conduits Grey mouldings. Alternative colours available to special order. Goosewing grey plates 2, 3 and 4 compartment boxes are also available with separate individual compartment base units for convenient offsite pre-wiring Supplied in parts or fully assembled and configured to customer specification Conform to IEC-61534-22 Pack

Cat. Nos.

4 compartment

Pack

Cat. Nos.

Empty boxes

75 mm compartment widths

75 mm compartment widths 1 1 1 1 1 1

CR4001 CR4002 CR4003 CR4004 CR4005 CR4006

Single base - 75 mm depth Single base - 85 mm depth (standard box) Single base - 110 mm depth Separate compartment base - 75 mm depth Separate compartment base - 85 mm depth Separate compartment base - 110 mm depth

1 1 1 1

Accessory plates – 75 mm width 1 1 1 1 1

CR4100 CR4101 CR4102 CR4104 CR4105 CR4118

1 1 1

CR4111 CR4117 CR4115

1 1 1 1

CR4106 CR4108 CR4112 CR4113

Blank plate 2 gang switched socket outlet 2 gang switched socket outlet, low noise / clean earth 2 gang unswitched socket outlet 3 gang unswitched socket outlet 3 gang unswitched socket outlet, low noise / clean earth 2 gang RCD socket outlet 2 gang RCD socket outlet, low noise / clean earth Angled punched plate for 4 x RJ45 (37 mm x 22 mm cut-outs) 2 x LJ2 accessory plate (50 mm fixing centres) 4 x BNC connector plate 4 x Data / Telecoms plate (37 mm x 22 mm cut-outs) 6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)

4 compartment pre-wired boxes

Single base – 85 mm depth, pre-wired with : CR122 2 x 2 gang switched socket outlets and 3 m standard tap-off CR123 2 x 2 gang switched socket outlets and 5 m standard tap-off CR132 2 x 2 gang switched socket outlets (low noise / clean earth) and 3 m low noise / clean earth tap-off CR133 2 x 2 gang switched socket outlets (low noise / clean earth) and 5 m low noise / clean earth tap-off

Ancillary items for service outlet boxes 1 1 10 10 50 1 1 1 1 10

CR0001 CR0003 CR0000 CR0010 CR0011 CR0002 CR0004 CR0005

Floor tile cut-out template – 2 compartment Floor tile cut-out template – 3/4 compartment Cable outlet flap Cable routers Screws for accessory plates Lid – 2 compartment box Lid – 3/4 compartment box Mounting frame for vinyl floor. For 2 compartment box Replaces mounting frame attached to base CR0006 Mounting frame for vinyl floor. For 3/4 compartment box. Replaces mounting frame attached to base CR0007 Floor box lid handle

Electrak tap-offs (see p. 18-21)

For other floor box configurations Contact us on +44 (0) 845 600 6266 29

030P_D2010 v1.qxd

4/6/10

10:06

Page 30

Access floor service outlet boxes

Access floor grommets

slab floor boxes

quick fit floor grommets

NEW

CR5302

EG0010

3 compartment slab floor box shown with two twin switched socket outlets, punched data plate and a power-track tap-off CR5102

EG0055

EG0020

Dimensions and technical information (p. 31) Electrak slab floor boxes are an ideal solution for underfloor power and data requirements Used in conjunction with Electrak floor grommets, slab boxes prevent unwanted access to power and data connections Pack

Cat. Nos.

Slab floor boxes Fast and efficient installation with integrated fixing plates Wide range of power and data accessory plates Manufactured from 0·9 mm thick galvanised steel Each compartment has 2 entries for 20 mm and 2 entries for 25 mm flexible conduits 100 mm compartment widths

1 1

Use plates from the 3 compartment floor box section CR5102 1 compartment slab floor box CR5302 3 compartment slab floor box 112 mm compartment widths Use plates from the 2 compartment floor box section

1

CR5202 2 compartment slab floor box

Quick fit installation from floor tile fixing to cable deployment Precision engineered from hard wearing durable flame retardant PC/ABS Grey mouldings. Other colours available to special order UL 94 VO flame class rating. Grommets conform to IEC-61534-22 Pack

1 1 1

1 1 1

Use plates from the 4 compartment floor box section CR5402 4 compartment slab floor box

For information on slab box configurations Contact us on +44 (0) 845 600 6266 30

Floor grommet 144 mm Ø

Can accommodate all cable types or three metal conduits up to a 20 mm diameter or 25 mm without foam Simply secured by pushing down the spring-loaded screws and rotating a quarter turn EG0010 Empty grommet EG0020 Cleaner’s grommet with unswitched socket outlet EG0031 144 mm grommet with punched plate for 4 x RJ45 NEW EG0050 Cleaners grommet with switched RCD protected socket EG1111 Cleaner’s grommet lid EG1112 144 mm grommet lid

Floor grommet 232 mm Ø

75 mm compartment widths 1

Cat. Nos.

1

Recommended for installation in light traffic areas EG0055 232 mm grommet

For information on grommet configurations and RCD protection Contact us on +44 (0) 845 600 6266

031P_D2010 v1.qxd

1/6/10

12:02

Page 31

Access floor service outlet boxes and grommets technical information

■ Floor boxes

■ Floor grommet 144 mm Ø

Dimensions Lid can accommodate carpets up to 6 mm depth Accessory plates are 172 mm long, with 162 mm fixing centres Materials Lid and trim mouldings are precision engineered from hard wearing durable ABS. Lid is reinforced with a Zintec coated mild steel plate Mounting frame and box base - 0·9 mm thick galvanised steel Floor service unit conforms to IEC-61534-22 Wiring Each compartment has 2 entries for 20 mm and 2 entries for 25 mm flexible conduits Colour Grey mouldings. Alternative colours available to special order Goosewing grey plates

Dimensions 144 mm Grommet EG0010

144 mm Ø

55 mm

Cleaner’s grommet EG0020 Complete with unswitched socket outlet

90 mm

125 mm min 127 mm min

Recommended hole cutter is a 5"/127 mm hole saw blade

Floor panel cut-out diameter

Dimensions from top of floor tile into floor void

Carpet aperture

66·85 mm

C

8 mm

A B 38·25 mm 66·85 mm

A (mm)

75 85 110

B Accessory box depth (mm)

35 45 45

C Underside lid to top of accessory (plug clearance) (mm)

40 40 65

■ To install box

■ Large floor grommet 232 mm Ø Dimensions Large quick fit grommet EG0055

232 mm Ø

58 mm

Cut hole in raised floor tile, lower complete box into aperture and push firmly down 213 mm min 215 mm max

Floor panel cut-out diameter Recommended hole cutter is a adjustable hole saw blade with Ø range of 40 mm - 300 mm

■ To install floor grommet A

B

Lift handle and pull to remove lid

Push grommet into raised floor tile aperture Push down spring loaded screws and rotate quarter turn to secure Ensure wings are located under floor panel For honeycombed floor panels one wing should face downwards and one wing should face upwards

C

D

E

Cable access insert Drop cable access insert into housing opening

Slide lid into lug holes

(1) Push down lid to close (2) If grommet is not in use, replace cable access insert

Floor tile cut-out dimensions 2 compartment : 263 mm x 203 mm(1) 3 and 4 compartment : 340 mm x 203 mm(1) Floor cut-out aperture is the same for single base or separate compartment base To fit carpet : Detach lid and trim assembly by lifting the blue locking handles and lifting out.

Cut and fit carpet. Push lid and trim assembly back into place

(1) The aperture dimension 203 mm has a fixing tolerance between 203 to 205 mm

Wing

1

2

31