JUNE 2011 t h e o f f i c i a l m a g a z i ne o f t h e co n c r e t e saw i n g & d r i l l i n g asso c i at i o n
Making a Splash at SkyCity Rooftop Pool Removal Aids Auckland Hotel Renovation Texas Airport Runway Cut and Sealed Chimney Removed by Wire Sawing in Hong Kong Mooring Structure Dissected at Mexican Port
w w w. c s d a . o r g
President’s Page
jim dvoratchek CSDA President
T
he Concrete Sawing & Drilling Association (CSDA), in pursuit of
Companies that achieve Level 2 certification have shown that they
excellence for all of its contractor members, officially launched
follow generally-accepted business practices based on the internationally
its newest Program of Excellence, the Company Certification
recognized ISO process. Level 2 companies have implemented effective
Program, in March of this year. Many customers today are requiring
business systems to operate more effectively on a daily basis which can lead
subcontractors to go through a pre-qualification process before they
to cost savings and improved customer satisfaction. Level 2 companies will
invite them to submit proposals or allow them to work on their projects.
meet the requirements for most heavy industrial projects.
This program will help CSDA members quantify their qualifications for doing the work that their customers specify. This pre-qualification requirement is driven by several factors. First, the customer desires to manage their risk by insuring that subcontractors
Companies that achieve a Level 3 certification are fully compliant to ISO9000 requirements. To achieve Level 3 certification, a company must pass a rigorous onsite audit of its quality management system that is comparable to an ISO9000 certification audit.
meet a baseline standard. Second, the project owner or insurance carrier
I invite you to undertake this process, if, for no other reason, than to
requires the subcontractor to meet a baseline standard to work at certain
identify those areas in your own organization where you excel. You can
facilities or on certain projects. Third, the contractor needs to determine
stress certification to your clients when you promote your company in
the best subcontractor to use on their projects and avoid needless problems
various marketplaces. In addition, the process helps highlight those weaker
on these projects. The CSDA Company Certification Program includes many
areas within your organization that can be improved. This information is
elements in its three levels that will assist the subcontractor in this pre-
vital to properly manage sawing and drilling companies. Visit the CSDA
qualification process.
Website today at www.csda.org to learn more about the Company
The Level 1 certification has been devised to determine if a company
Certification Program.
meets the stringent requirements set forth by CSDA. By attaining Level 1, these companies have demonstrated a strong commitment to professionalism in management and business practices.
w w w. CSD A .ORG
c on c re t e o p e n i n g s | 1
If cutting concrete, stone or masonry is your game...
New 695 Series Utility Chain Saws been using ICS chain saws for a long time. They’re great “ We’ve for deep, straight cuts and square corners. The 695 series is a real game changer. Quieter, lighter weight and less vibration. That makes us more productive and more profitable.
”
– George Cramer, President, Bedrock Concrete Cutting Inc.
We understand what contractors like George Cramer go through every day. So every day, we push ourselves to perfect our tools and technology to make a rough, dirty job a little easier and you even more effective.
Watch how we’re changing the game at icsbestway.com For product information, call 800.321.1240 or visit a dealer near you. ICS | Blount Inc. · 4909 SE International Way · Portland, OR 97222 USA · Ph 800.321.1240 · Fax 503.653.4393
icsbestway.com ©2011 ICS | Blount Inc. All rights reserved. 1110. 695F4 pictured.
t h e o f f i c i a l m a g a z i n e o f t h e c o n c r e t e s a w i n g & d r i l l i n g a s s o c i at i o n
CSDA OFFICERS
concrete cases
President, Jim Dvoratchek Hard Rock Concrete Cutters, Inc. jimd@hardrockconcretecutters.com
Making a Splash at SkyCity
Vice President, Judith O’Day Terra Diamond Industrial joday@terradiamond.com
Rooftop Pool Removal Aids Auckland Hotel Renovation
Secretary/Treasurer, Mike Orzechowski DITEQ Corporation mikeo@diteq.com Past President, Doug Walker Atlantic Concrete Cutting, Inc. dwalker@atlanticconcretecutting.com Executive Director, Patrick O’Brien Concrete Sawing & Drilling Association pat@csda.org CSDA BOARD OF DIRECTORS (Terms expiring in 2012)
8
Tim Beckman Cutting Edge Services Corporation beckman@cuttingedgeservices.com Steve Garrison Hilti, Inc. steve.garrison@hilti.com Donna Harris Concrete Renovation, Inc. donna.cri@sbcglobal.net Ron Rapper Husqvarna Construction Products ron.rapper@husqvarna.com
12
Roger Allen Diamond Tools Technology roger@diamondtoolstechnology.com Ty Conner Austin Enterprise tconner@austin-enterprise.com
20
Mike Greene Greene’s, Inc. mikeg@greenesinc.com Larry Liddle Diamond Products Limited lliddle@diamondproducts.com Kellie Vazquez Holes Incorporated kvazquez@holesinc.com Kevin Warnecke ICS, Blount Inc. kwarnecke@icsbestway.com
w w w. CSD A .ORG
Cutter Can Take the Heat Contractor Demolishes Chimney at Incineration Plant
Jack Sondergard Central Concrete Cutting, Inc. jacksondergard@sprynet.com CSDA BOARD OF DIRECTORS (Terms expiring in 2013)
Sealing the Deal Former Air Force Base Runway Repaired by CSDA Member
Kevin Baron Western Saw, Inc. kevinb@westernsaw.com
Port of Tampico Berthing Structure Removed with Wire Saw
34 c on cre t e o p e n i n g s | 3
Concrete Openings Magazine Official Magazine of the Concrete Sawing & Drilling Association Volume 20, Number 2
c o n t e n t s
ISSN: 1093-6483
1
President’s Page
Concrete Openings magazine is published by O’Brien International, Inc., four times each calendar year in March, June, September and December. Editorial contributions are welcomed and advertisements are encouraged. Please contact the Concrete Sawing & Drilling Association 13577 Feather Sound Drive, Suite 560 Clearwater, FL 33762 Tel: 727-577-5004 Fax: 727-577-5012
7
CSDA Launches Company Certification Program
www.csda.org Magazines, newspapers and private individuals are welcome to reproduce, in whole or part, articles published herein provided that acknowledgements are made in the following manner: “Reprinted courtesy of the Concrete Sawing & Drilling Association, Concrete Openings magazine, Issue Date.” No alterations should be made in the text of any article. Publisher Patrick O’Brien Editor Cherryl O’Brien ASSOCIATE Editor Russell Hitchen CONCRETE CASE Contributors Penny Simons Raul Bracamontes Cheryl Sment Bibi Wong Sze Chai Editorial Review Committee Skip Aston Rod Newton Pat Stepanski The information and recommendations in this magazine are provided for use by fully qualified, professional personnel. The Concrete Sawing & Drilling Association and the publisher disclaim any responsibility as to their use by readers and shall not be liable for damages arising out of the use of the foregoing information. All bylined articles published in this magazine represent solely the individual opinions of the writers and not necessarily those of the Concrete Sawing & Drilling Association.
Cover Photo: The SkyCity Hotel and Sky Tower, Auckland, New Zealand.
4 | JU NE.1 1
16 Tech Talk
Core Cracking – Safety and Performance
24 CSDA Convention Attendance Up 30 Percent 26 Back in the Saddle—Jim Dvoratchek 28 Core Health Nutrition for Job Performance
30 The Business of Business Ten Ways to Cut Fuel Costs
38 Cutting Close to Home
Core Drilling at the CSDA Offices
40 Safety Counts
New OSHA Guidance on Employee PPE
43 OSHA / CSDA Alliance Latest 44 Insurance Corner
How to Earn an “A” Grade on Your Workers’ Compensation Insurance Report Card
46 Industry Bits 58 Certified Operator Companies 60 Calendar 61 New Members 64 Director’s Dialogue
40
international patents pending
30 Years of Innovation
Why would you invest in anything less?
Concrete cutting the 14,572-foot-long Bay Runway at JFK Airport. 6 | JU NE.11
CSDA Launches Company Certification Program Cutting Edge Services of Batavia, Ohio—the First Company to be Certified
T
he Concrete Sawing and Drilling Association formally launched its newest Program of Excellence, the Company Certification Program, at its recent annual convention. The 3-tier program was developed by the CSDA Certification Committee for cutting contractors to provide owners, architects, engineers, general contractors and government officials with a valuable pre-qualification tool and to enhance the level of professionalism possessed by concrete sawing and drilling contractors. The new Company Certification Program is the first of its kind in the industry. In addition, it was announced that CSDA member Cutting Edge
Level 3 certification, the company must have successfully implemented
Services Corp. of Batavia, Ohio, became the first contractor to be certified
all the requirements of a Level 1 and Level 2 certification plus have
at Level 1 of the Program.
effectively implemented a best practice for records control, corrective
Level 1 certification was developed to demonstrate that a company meets the stringent financial, operational and safety requirements of the industry to do business as a professional sawing and drilling contractor. To achieve Level 1, companies must successfully pass a written review. “I am extremely pleased to have my company be the first to achieve Level
and preventive action and internal auditing that assesses the effectiveness of the company’s quality management system. To achieve Level 3 certification, a company must pass a rigorous on site audit of its quality management system that is comparable to an ISO9000 certification audit. A company that has achieved Level 3 certification has met the highest standards set by CSDA and is fully compli-
1 status,” said Tim Beckman, owner of
ant to the ISO9000 international quality standard.
Cutting Edge Services Corp. “The CSDA
For more than 10 years, CSDA has had a
Company Certification Program provides
certification process in place for individual sawing
me with documentation that can I pres-
and drilling operators. Operators are certified in
ent to customers and general contractors.
cutting disciplines of slab sawing, core drilling,
I can prove that the company not only
wall and hand sawing and wire sawing. This new
performs safe and efficient cutting work,
certification program extends the reach of the
but also uses sound business practices.”
certification process from the individual operator
Level 2 includes heavy industrial
to the entire company.
prequalification. To attain Level 2, a
The Company Certification Program is being
company must prove that they have
administered by a third party auditor, Asurency, Inc.,
implemented sound business practices.
to maintain complete confidentiality of all records.
The Level 2 certification covers all the
Asurency, Inc. has more than 15 years experience
requirements of the Level 1 certification
in conducting certification audits and business and
plus an assessment of each of the fol-
ISO implementation counseling. Asurency, Inc. is
lowing processes: subcontractor control, maintenance, planning, sales, training, purchasing, design, calibration, measure-
experienced in several market segments including Tim Beckman of Cutting Edge Services Corp.
ment systems, continuous improvement and management system review. In addition, the company must have procedures in place for these processes to ensure consistent practices. To achieve Level 2 certification, companies must successfully pass a written review.
construction, light and heavy industrial, high-tech and the service industry.
The CSDA Company Certification Program is available to all sawing and drilling contractors. For more information, visit www.csda.org and click on the Company Certification Program banner or contact the CSDA office at 727-577-5004. The application can be accessed via the Asurency, Inc. Website at www.asurencyglobal.com and clicking on the CSDA banner
Level 3 will provide potential customers with proof that a company
on the lower left hand side of the screen. Asurency, Inc. can also be reached
has an effective Total Quality Management System in place. To achieve
at 952-994-2097.
w w w. CSD A .ORG
c on cre t e o p e n i n g s | 7
SkyCity rooftop pool removal project. 8 | JU NE.11
CONCRETE
Making a
CASES
Splashat SkyCity Rooftop Pool Removal Aids Auckland Hotel Renovation
A
development plan for a luxury hotel and casino in Auckland, New Zealand, consisted of extra floors that include four VIP villas with gaming
areas and VIP salons. In order to add these extra floors, a rooftop swimming pool needed to be removed. SkyCity is one of Auckland’s biggest hotels, with over 340 rooms
and views of the city’s harbor. One of the main draws of the hotel is the Sky Tower, a 328-meter-tall (1,076-foot) building that is the largest man-made structure in New Zealand. Visitors can dine in one of the tower’s restaurants or perform a 192-meter (630-foot) wire jump from the tower’s viewing platform. The VIP area development project was scheduled for completion in June 2011. This is so that the hotel will be prepared for a large volume of high-profile visitors arriving in September for the 2011 Rugby World Cup, an international tournament that features 20 teams and runs for two months. The removal of the rooftop pool was scheduled for three weeks in February, and had to be done quickly to keep the project on track while keeping disruption of hotel operations to a minimum. The pool measured 13.3 meters (43.6 feet) long, 5.1 meters (16.7 feet) wide and had a depth ranging from 1.2 meters (3.9 feet) to 1.8 meters (5.9 feet). The concrete walls and floor of the pool were 250 millimeters (9.8 inches) thick. The general contractor for the project, Hyline Construction Ltd. of Auckland, began searching for a contractor that could take out the concrete pool without causing large amounts of vibration and noise that would disturb hotel guests. A1 Kiwi Cutters & Drillers Ltd., a CSDA member based in Auckland, was contracted by Hyline to remove the pool. The plan devised by A1 Kiwi Cutters and approved by Hyline, called for the walls of the pool to be cut into 16 sections using a wall saw with diamond blades. It was specified that none of the cut sections could weigh more than 2.7 tons due to capacity of the crane on site. Each cut section would have two 132-millimeter-diameter (5.2-inch) holes core drilled into it so that lifting straps could be attached, then the section could be removed by the crane. Before the final cut was made on each section, the piece would be rigged for removal. The floor of the pool was to be cut into 14 sections using a floor saw, and a similar method was used to hold the weight of the cut piece before the final cut and removal. A1 Kiwi Cutters was responsible for the provision of machinery, labor and slurry control during all the cutting and drilling processes.
w w w. CSD A .ORG
The Auckland Skyline.
As the hotel was to remain fully operational during the work, wall sawing and diamond core drilling was the best choice. Wall sawing is much more quiet and efficient than demolition methods like jackhammering or the use of a wrecking ball. “This technique meant minimal disruption for the hotel staff and guests, as there would be less vibration, less debris and the cutting would not be as labor-intensive as breaking or wrecking,” said Penny Simons, co-owner of A1 Kiwi Cutters & Drillers Ltd. The cutting contractor worked closely with Hilti New Zealand Ltd. and used a DS TS20-E wall saw to perform the majority of the cuts. The first step was to wall saw the internal perimeter where the pool walls met the pool floor. The cuts were made 50 millimeters (2 inches) above the joint and were completed in five hours. It was then time to core drill the 132-millimeter-diameter (5.2-inch) holes for the lifting straps. Two holes were cored per section using a Hilti DD200 core drill. The final part of the pool job involved vertical wall sawing. The walls were divided into 16 pieces and measured to be no longer than 2.4 meters (7.9 feet) and weigh no more than 2.7 tons. The sections were rigged while the final cut was being made, then the piece was removed from the work area. The process was repeated until all 16 sections had been cut free. This took six days to complete. Once all of the concrete pool wall sections were removed from the work area, the cutting team began to mark out the floor of the pool for cutting and core drilled holes measuring 132 millimeters (5.2 inches) in diameter to attach lifting straps. An operator then used the floor saw to
c on c re t e o p e n i n g s | 9
The 13.3-meter-long (43.6-foot) rooftop swimming pool was to be cut and removed.
A wall saw was used to cut through the pool walls that were 250 millimeters (9.8 inches) thick.
cut the pool floor into 14 sections, again ensuring that each section was
of lifting holes and rigging the section to the crane prior to each
no heavier than 2.6 tons. As with the pool wall sections, each cut floor
final cut. Another safety concern was the weather. The work was
section was rigged by crane before making the final cut and removing
completed during the summer months and operators were exposed
the piece from the work area. The cutting of the pool floor concrete
to the sun for long periods of time while working on the rooftop.
took 10 days.
The contractor made sure that all operators used sunscreen, stopped
During the entire cutting work, slurry was collected via wet vacs and
regularly for breaks and kept hydrated. All operators wore standard
stored in sealed containers. When filled, these containers were lowered
personal protective equipment like steel toe capped boots, hi-visibility
by crane and then emptied by environmental contractors who disposed
vests, hard hats, gloves, ear and eye protection.
of the slurry according to current legislation. Control of the slurry and waste water was critical, as A1 Kiwi Cutters had to make sure that no waste leaked into the occupied hotel rooms on the floor below. Due to the strict time frame applied to the whole project, time was of the essence. The hotel stood to lose a large amount of revenue if the new facilities were not available for the Rugby World Cup. In order to complete the job, A1 Kiwi Cutters had up to five operators on site most days. Mark Simons, director of A1 Kiwi Cutters & Drillers Ltd, oversaw the day-to-day management and organization of the team. Simons operated the wall saw while operators took care of the core drilling, floor sawing and slurry control. The pool was successfully removed in 16 days. The main safety concern was the risk of pool sections falling before being removed. This concern was overcome by the core drilling
The floor was cut into 14 sections weighing 2.6 tons each.
1 0 | JU NE.1 1
A Hilti DS TS20-E Wall Saw was used to perform the vertical cuts to the interior walls of the pool, while the cuts to the floor of the pool were made by a 35-horsepower Core Cut floor saw from Diamond Products. Hilti also supplied a DD200 core drill to create the picking holes for the crane rigging, while Husqvarna K1250 and K960 cut and break saws were also used for some parts of the cutting work. Slurry and waste material were collected using a WVD2002 twin motor wet vacuum from Numatic. To cut and remove the rooftop swimming pool at the SkyCity Hotel, A1 Kiwi Cutters & Drillers Ltd used the wall saw to cut over 65 meters (213 feet) of cuts and a floor saw to perform over 100 meters (328 feet) of cutting. For rigging of the concrete pieces, the contractor core drilled over 140 holes before attaching to the crane and removing over 80 tons of concrete. The CSDA member completed the job within the expectations
Cut sections were rigged and removed from the work area by crane.
of Hyline Construction and within budget. Following the successful completion of the pool removal project, the
important to be involved, so he operated the saw and assisted with
contractor has been further contracted by both Hyline Construction and
the work. We think this says a lot about our company,” she added.
Hawkins Construction to work on other parts of the overall project. “The pool removal work done at SkyCity Hotel gave us an opportunity
The development work at SkyCity Hotel completed in June 2011 thanks to this CSDA member making a big splash.
to show what we can do with our market-leading equipment and a dedicated team,” said Penny. “Hilti tells us that our high-freqency wall
REVIEW AND COMMENT ON THIS ARTICLE AT: WWW.concreteopenings.com/FORUM.CFM
saw is the only one in New Zealand. Our director, Mark Simons, felt it was
Company Profile
Established in 2005, A1 Kiwi Cutters & Drillers Ltd. merged with Access Concrete Cutting in 2008 to become one of the largest concrete cutting companies in Auckland, New Zealand. The company joined CSDA in 2009 and has 14 operators and 10 trucks. The company offers the concrete cutting services of bar sawing, grinding, core drilling, slab sawing, ferroscanning, hand sawing, ring sawing, wall sawing, wire sawing and floor polishing and preparation. Resources
General Contractor: Hyline Construction Ltd. Sawing and Drilling Contractor: A1 Kiwi Cutters & Drillers Ltd. Auckland, New Zealand Phone: 64-9 420 3386 Email: thegirls@kiwicutters.co.nz Website: www.a1kiwicutters.co.nz Methods Used: Wall Sawing, Slab Sawing, Core Drilling The contractor cut and removed over 80 tons of concrete.
w w w. CSD A .ORG
c on c re t e o p e n i n g s | 1 1
Former Air Force Base Runway Repaired by CSDA Member
I
n spring of 2010, the City of Austin, Texas, put out to bid the Airfield Portland Cement Concrete Joint Sealant Rehabilitation
Project. This project included 1.3 million lineal feet of joint rehabilitation and 1,100 square feet of PCC spall repair at the Austin-Bergstrom International Airport. The project would involve the repair and sealing of joints on the airport’s oldest runway that measured 12,248 feet in length. The project was to be completed in 330 days.
Austin-Bergstrom International Airport was once a U.S. air base.
1 2 | JU NE.1 1
Photos this page courtesy of Austin-Bergstrom International Airport.
Sealing theDeal
CONCRETE
CASES
A 12,248-foot-long runway required sawing and resealing.
The airport site was originally an air base
varying age and type of sealant used, as well as
method was dismissed, however, because of
for the U.S. Air Force before being handed
the varying age and condition of the concrete.
the varying age and condition of the concrete.
over to the City of Austin in 1993. Personnel
The project was awarded to CSDA member
Sawing with diamond blades provided us with
from Bergstrom Air Force Base contributed
Interstate Sealant & Concrete, Inc. (ISC) of
both the precision and the speed needed to
to every U.S. war effort before the base was
Waukesha, Wisconsin. The contractor is a
complete the project,” said Gregg Sment,
deactivated, and the U.S. Air Force Reserve
certified Disadvantaged Business Enterprise
project manager for ISC. From preliminary test
continued to operate from the base until 1995.
and a certified Women’s Business Enterprise.
cutting, operators found that diamond cutting
Four years later, the airport began passenger
Interstate was hired to work directly with the
left the joints crisper, which made the project
services and was renamed Austin-Bergstrom
airport’s Aviation Department to plan how the
less labor intensive as less scraping was needed.
International Airport, which now handles over
work was to be done and devise a work schedule.
The first task was to remove the old
9,000,000 passengers a year.
As various sections of the concrete runway had
sealant from the existing joints. This involved
Major updates took place at the airport
been previously repaired and rehabilitated, saw
shaving both edges of the existing joint to
from 1996 to 1998 to make it a civilian airport,
cutting with diamond tools was considered the
free up the bond on the old sealant with a
including the addition of a second runway and
best option. This technique would minimize
85-horsepower 8500D ride-on slab saw from
additional passenger and air cargo aprons.
additional spalling of the concrete.
Husqvarna. Once the sealant was free, it was
However, the majority of the concrete on the
“Due to the size and scope of the job, we
pulled or plucked from the joints by hand. This
first runway had been in place since the air
had considered joint plowing, a method that
process was carried out by five operators and
field was built in the 1940s and had undergone
utilizes a toothed jig to pull the old sealant out
17 laborers and took 65 days to complete. All
several rounds of patch-up work and repairs.
of the joint, to rehabilitate the concrete. This
processes ran simultaneously.
Conditions that impacted this job included the w w w. CSD A .ORG
c on c re t e o p e n i n g s | 1 3
CONCRETE
CASES
Compressed air was blown into 1,319,062 feet of joints before the joints were sealed.
After the old sealant was removed, the
these areas, ISC operators cut the perimeters of
the least amount of disruption possible, even
joints were cleaned with custom-built wire
the spalled concrete until they reached sound
though it meant the crews went to different
brush machines. The brushes used were
concrete. The interior of the saw-cut area
work areas almost every day,” said Hathaway.
custom-made to ISC specifications and were
was then removed before being cleaned and
To create clean and safe joints for the new
manufactured to be free of oils and other
sandblasted. Delpatch elastomeric concrete
sealant to be installed on runway 17R/35L
manufacturing contaminants. Contaminant-
from the D.S. Brown Company was used to
at Austin-Bergstrom International Airport,
free compressed air was then blown into the
fill back the prepped spalls, and this process
Interstate Sealant & Concrete, Inc. used five
joints to clear them of any remaining sealant,
was finished by hand. The contractor repaired
Husqvarna 8500D ride-on slab saws with 85-
dust or debris, before the backer rods were
287 spalled areas that covered approximately
horsepower engines. Wire brush machines
replaced. New backer rods were installed
1,175 square feet in total.
were custom made by ISC and used to prepare
and checked to make sure they achieved a
The biggest challenge for the CSDA
the joints, along with silicone pumps from
specific depth with a 2:1 ratio. Backer rod
member on this project was to avoid impacting
Graco and sand pots from Schmitt. In total,
sizes of 0.625 inches all the way up 1.25 inches
air passenger services, or at least keep any
ISC cut and resealed 1,319,062 linear feet of
were used. Following this installation, the
necessary disruptions to an absolute minimum.
concrete and repaired 1,175 square feet of
joints were once again blown clean with
This included minimal interruptions at gate
spalls in the concrete. On average, the team
compressed air.
areas and keeping runway closures to the
completed 20,000 feet per day, which had
Now that the joints had been prepared for
shortest possible time frame. The terminal
a positive impact on the project end date.
the installation of the new sealant, the team
ramp was completed in six days. ISC’s general
After being allocated 330 calendar days by
from ISC set up two Graco sealant pumps to
superintendent Dana Gillespie and supervisor
the airport’s aviation department to complete
apply 18,589 gallons self-leveling silicone from
Dan Hathaway coordinated with the airport
the work, the contractor finished all scheduled
Dow Corning for the runway project. It took
operations staff daily to keep runways open.
tasks in 133 days.
45 days to complete the resealing.
“These daily meetings were really important.
The contractor’s biggest concern, however,
A number of areas on the concrete
It was a continual, coordinated work effort to
was the heat. ISC was given notice to proceed
runway were identified as spalling. To repair
get our crews around the airport while causing
on July 26, 2010, when average airport tem-
1 4 | JU NE.1 1
The contractor also repaired 1,175 square feet of spalls.
peratures can exceed 100 degrees. Many of
oped to rotate workers off the job during the
the tool box talks and safety meetings held
work day to minimize their exposure to the
by the project manager covered topics like
sun and heat.
heat exhaustion and heat stroke. Supervisors
Dale Thompson, air field project manager
and foremen were provided with additional
for Austin-Bergstrom Internationl Airport,
on-the-job education. A plan was also devel-
was extremely pleased with the result. “It was critical that we minimized the amount of time that runways were closed to airway traffic. ISC understood this, and the team scheduled and performed their work in exemplary fashion. As an example, we alloted 60 calendar days for one work area on the east runway and
Company Profile
Interstate Sealant & Concrete, Inc. has been in business for 14 years and is based in Waukesha, Wisconsin, with a support operation in Lansing, Michigan. The company is a new member of CSDA and has 50 employees and 50 trucks. The contractor offers the services of flat sawing, joint sealing, crack sealing, partial depth repairs and epoxy crack injection.
the crews finished in 10 days. Needless to say,
Resources
with that kind of production rate we worked
General Contractor:
to accommodate ISC’s requests as we were
Austin-Bergstrom International Airport
confident in the work being produced,” he said. The work began in September 2010 and was signed, sealed and delivered three months later in December. Runway 17R/35L is now in much better shape to handle the growing number of passengers making their way to Austin, Texas, thanks to this CSDA member.
Sawing and Drilling Contractor: Interstate Sealant & Concrete, Inc. Waukesha, Wisconsin Phone: 262-547-6316 Email: csment@interstatesealant.com Website: www.interstatesealant.com Methods Used: Slab Sawing, Joint Sealing
Custom-made wire brush machines cleaned the joints.
w w w. CSD A .ORG
REVIEW AND COMMENT ON THIS ARTICLE AT: WWW.concreteopenings.com/FORUM.CFM
c on c re t e o p e n i n g s | 1 5
Tech Talk Tech Talk is a regular feature of Concrete Openings magazine, focusing on equipment, maintenance and operational issues of interest to concrete cutting contractors. Readers wishing to have a particular subject addressed can call or email CSDA with their suggestions at 727-577-5004 or rhitchen@concreteopenings.com.
Core Cracking - Safety and Performance By Kevin Baron and Anthony Baratta
A
ll cores should be inspected at regular intervals and must be retired immediately if core cracking is observed. This is the standard outlined by the Saw Manufacturers Institute (SMI), Occupational Safety and Health Administration (OSHA) and the American National Standards Institute (ANSI). Safety is the number one concern for each of these governing bodies and should be for any company. Another important concern for concrete cutters, however, is how to get the best performance and greatest value from diamond tools. Following is valuable information regarding the manufacture of diamond cores and cutter best practices. This information will help minimize the chance of core cracking, maintain safety and achieve the performance levels required for the job.
Heat Treatment Heat treatment is the process in which the steel core’s microstructure is rearranged to control the mechanical properties like strength, hard-
Manufacturing Material and Fabrication Process
ness and fatigue resistance. Post tempering relieves stress and helps to flatten the core after quenching. It is optimal to achieve a surface hardness of Rockwell 38Rc for high-abrasion resistance. In addition, a lower
The combination of raw materials and fabrication is a key element
core hardness is desirable since it increases fatigue resistance and overall
in the manufacturing of a steel core. The steel used in the manufac-
core life. Hardness is also critical for flatness and tension since cores with
ture of cores is perfectly suited for the application by having high
inconsistent hardness (spotty hardness) are difficult to smith and will
strength, toughness and abrasion resistance to meet the demands of
not hold tension. This will cause premature failure of the diamond tool.
today’s cutting applications and higher powered saws. The composition of steel also accepts laser-welded or brazed segments with minimal changes to the mechanical properties. Laser cutting of the core is the most desirable manufacturing process because punching, milling and grinding can cause micro cracks and stress concentrations which increase the likelihood of core cracking.
Surface Grinding Rotary surface grinding removes surface imperfections such as raw material crown, scale and scratches. This helps to normalize and level the surface, reducing the possibility of core cracking from stress concentrations. 1 6 | JU NE .1 1
w w w. CSD A .ORG
c on c re t e o p e n i n g s | 1 7
Leveling, Smithing and Tensioning Proper leveling, smithing and tensioning insure longer life, better performance and greater value for the contractor. Cores that are leveled and smithed flat will take and hold tension much longer than cores without. Tensioning, leveling and smithing will produce a core that runs true longer. Cores that run true will not wobble, heat up or fatigue nearly as fast. This can significantly increase core life and performance.
Core Diameter (inches)
Core Diameter (millimeters)
Operating rpm for 9500 sfpm
4 102 4.5 114 5 127 6 152 7 178 8 203 9 229 10 254 12 305 14 356 16 406 18 457 20 508 22 559 24 610 26 660 28 711 30 762 32 813 34 864 36 914 38 965 40 1,016 42 1,067 44 1,118 46 1,168 48 1,219 50 1,270 52 1,321 54 1,372 56 1,422 58 1,473 60 1,524
9,100 8,100 7,300 6,000 5,200 4,500 4,000 3,600 3,000 2,600 2,300 2,000 1,800 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000 910 860 820 790 760 730 700 670 650 630 600
Equipment Care Keeping equipment in good working condition is critical to the safety of operators and the performance of diamond tools. Without proper maintenance and care of equipment, the life and performance of diamond tools is greatly reduced. Machining the Outside Diameter Machining the outside diameter is critical for the core balance and concentricity. Cores must be concentric to ensure proper segment mounting and balance. This will also minimize the likelihood of hammering while cutting, especially if the segments are also outside diameter ground. The following are best practices that will help minimize core cracking, increase performance and provide the most value from diamond tools.
Blade Shaft Bearings, Collars and Mounting Hardware Vibration is one of the main causes of core cracks and blade fatigue. Maintaining blade shaft bearings, collars and mounting hardware are essential to reducing vibration and increase diamond blade performance by minimizing hammering. Cooling of Diamond Blades Heat is also a main cause of core cracking and loss of tension.
Best Practices
Without tension, a diamond blade will not run true. It will contact
Select the Correct Tool for the Job
the sidewall, generate excessive heat and fail prematurely. Therefore,
In order to specify the correct diamond tool for the job, operators need to know the hardness of the material to be cut, the tool speed, the equipment power, the cooling method and the mounting type. The correct diamond tool for the application will increase diamond tool performance and reduce core cracking. Operational Speed The operator must make sure that the diamond tool is run at the correct revolutions per minute (rpm) to get the best performance from the diamond tool and insure their safety and that of others in the work area. Over speeding and over feeding a diamond tool will cause premature tool failure by increasing the amount of heat in the core and exceeding the mechanical properties of the steel. The following table shows the recommended rpm for 9,500 surface feet per minute (sfpm) blade speed. 1 8 | JU NE .1 1
a wet blade must have ample water to cool it properly. For a dry cutting tool, it is essential to operate within the blade manufacturer’s recommended tool speed and not to apply too much side load. These practices will help the blades operate within the design temperature and help to insure diamond blade performance and life. The information provided in this article will help contractors keep their operators safe and maintain the profitable performance of diamond tools. Any questions or matters that require clarification should be directed to an official diamond tool manufacturer. Kevin Baron is the president of Western Saw, Inc., based in Oxnard, California, and is the chairman of the CSDA Manufacturer Committee. Anthony Baratta also works for Western Saw as the company’s chief engineer. Kevin and Anthony can be reached at 805-981-0999 or by email at kevinb@westernsaw.com and anthonyb@westernsaw.com.
GPRS, Dallas, TX USA
Scan It. Cut It. Core It. Concrete Inspection for the Sawing and Drilling Contractor
Aquitaine Radar, Lagarrigue France
The StructureScanTM Family by GSSI: StructureScan Mini StructureScan Optical StructureScan Standard
Geophysical Survey Systems, Inc. w w w. CSD A .ORG
www.geophysical.com • sales@geophysical.com
Seattle, WA USA c on c r e t e o p e n i n g s | 1 9
Cutter Can
Take theHeat
Contractor Demolishes Chimney at Incineration Plant
T
he project description was straightforward. Demolish a 150-meter-tall (492-foot) concrete chimney stack at a redundant incineration plant in Hong Kong so that the site could be cleaned up for reuse. However, the location of this particular chimney meant that it was not simply a case of bringing down the structure as quickly as possible, but bringing it down in a controlled manner that would not cause excessive noise or vibration. This was the challenge presented to one CSDA contractor. The chimney, the tallest of its kind in Hong
First, scaffolding could have been erected to
Kong, was part of the Kwai Chung incineration
enclose the external wall and the chimney
plant that operated from 1978 to 1997. The
could be broken down by jackhammers. Debris
cynclindrical-shaped
in
would be allowed to fall through the center
diameter from 12 meters (39.4 feet) at the base
of the stack. The second idea was similar, and
to 6 meters (19.7 feet) at the top. The thickness
involved using a demolition robot on a platform
of the chimney stack wall also decreased from
attached to a crane. The robot could break the
the base to the top, from 1,000 millimeters
concrete down from the top of the stack and
(39.4 inches) to 200 millimeters (7.9 inches). A
be lowered at intervals. Both of these methods,
single, circular pile cap formed the foundation
however, caused too much noise, vibration and
of the structure, which was 16.5 meters (54.1
debris for the general contractor, and so a third
feet) in diameter and sat on 30 bored piles that
was approved. This method involved the use of
A portable work platform was set up on the
were each 1,200 millimeters (47.2 inches) in
diamond wire to cut the chimney into a series
ground around the perimeter of the chimney,
diameter and measured 36 meters (118 feet)
of concrete rings that would be encased in a
which included eight lifting brackets that would
deep. The aim was to level the incineration plant
protective scaffold setup during cutting and be
allow the platform to be moved up or down the
before decontaminating the site. The plant and
lowered to the floor by crane.
stack with a good level of stability. The platform
chimney
tapered
A wire saw was used to cut the chimney into 55 sections from the top down.
surrounding land was owned by the Kwai Chung
Modern Drill Cut’s plan was to set up three
was lifted to the top of the stack, where two
Drainage Services Department and the land was
remote-controlled wire saws on the inside of
lifting supports were installed for gondolas that
to be reused.
the chimney stack before cutting the concrete
would transport the cutting equipment to the
Attempting to demolish the stack using
structure into 55 circular pieces. Each cut section
various levels during wire sawing. Hydrostress
traditional methods may have caused falling
would weigh between 30 and 100 tons and
FZ-2S handheld saws were used to form vertical
debris to hit adjacent structurally sound
measure around 2 meters (6.6 feet) in height.
cut lines in the stack before the wire saw was
buildings or an elevated highway that was
A 600-ton, 170-meter-tall (558-foot) crane was
used to make the horizontal cut line and free
located just 20 meters (65.6 feet) away from
to be positioned close to the work area to carry
the section from the remaining structure. The
the work area. The project was contracted by
the cut sections down to the floor, where the
work platform was then lowered into position,
China International Water & Electric Corp., and
concrete would be broken down into small
3 meters (9.8 feet) below the top cutting edge,
CSDA member Modern Concrete Drill Cut Co.,
pieces for removal. Operators could remain a
before the cut section was secured to the plat-
Ltd of Kwun Tong, Kowloon, Hong Kong, was
safe distance from the cutting area too. The
form and lowered to the ground by the crane.
awarded the job.
use of the wire saw provided minimal noise and
This process took 10 hours to complete and was
debris, and there were considerable savings in
repeated until the remaining section of the
time compared to other techniques.
chimney stack stood 10 meters (32.8 feet) from
The contractor suggested three different methods for the demolition of the chimney.
2 0 | JU NE .1 1
CONCRETE
w w w. CSD A .ORG
The Kwai Chung incineration plant chimney stood almost 500 feet.
CASES
c on c re t e o p e n i n g s | 2 1
CONCRETE
Cut sections weighing between 30 and 100 tons were lowered to the ground by crane.
the ground. This part of the structure was then
A Hydrostress 40-kilowatt FZ-2S wall saw
broken down using traditional demolitions meth-
from Tyrolit was used to create the vertical cut
ods as the risk of falling debris was much lower.
lines on the chimney stack and three Hydrostress
The obvious challenge for this CSDA member
SK-AD universal wire saws were used to perform
was the height of the structure being cut. Strong
the larger horizontal cuts. Over the course of
winds, particularly at the top of the 150-meter-
90 days, the team from Modern Concrete Drill
tall (492-foot) chimney, were a concern and the
Cut Co., Ltd. cut 2,800 cubic meters (98,881cubic
contractor had to make sure that operators were
feet) of concrete with diamond wire to demol-
securely tied off. The other factor that the team
ish the chimney stack at the Kwai Chung incin-
from Modern Concrete Drill Cut had to be aware
eration plant. A further 1,200 square meters
of was the proximity of surrounding buildings,
(12,916 square feet) of vertical concrete cutting
structures and the nearby highway.
was performed.
CASES
Once on the ground, the cut chimney sections were broken down and removed from site.
Company Profile
Modern Concrete Drill Cut Co., Ltd. joined CSDA in 2009 and has been in business for 11 years. The company is based in Kowloon, Hong Kong and has support offices in Macau, Singapore and China with 200 total employees. The contractor offers the services of flat sawing, wire sawing, selective demolition, floor preparation,
The contractor considered many elements
The project was completed within the sched-
when planning the work and made sure that
uled time period and allocated budget. The main
safety was a constant. Personal protective equip-
reason for this was that the concrete was not
Resources
ment was provided for operators, including har-
as hard as initial surveys had suggested, so cut-
General Contractor:
nesses for working at height. Safe plant operat-
ting speeds increased. The other advantage for
China International Water &
ing zones were identified and fenced off while
the contractor was that the company had been
Electric Corp.
temporary lighting was installed inside the chim-
involved in the cutting and removal of chimneys
Sawing and Drilling Contractor:
ney. Modern Concrete Drill Cut also installed fire
before and was well prepared for this job. As a
Modern Concrete Drill Cut Co., Ltd.
fighting equipment and emergency escape routes
result, Modern Concrete has now been chosen
Kowloon, Hong Kong
were clearly marked. To keep the dust and debris
to remove another chimney at the Pandan incin-
at the work area to a minimum, an extraction
eration plant, the tallest chimney in Singapore.
fan was used to collect dust from the inside of
Having the right tools and carefully planning any
Email: info@modernok.hk
the chimney.
job will ensure that a contractor doesn’t feel the
Website: www.modernok.hk
heat, even at an incineration plant. REVIEW AND COMMENT ON THIS ARTICLE AT: WWW.concreteopenings.com/FORUM.CFM
2 2 | JU NE.1 1
excavation and crushing.
Phone: 852-2342 922
Methods Used: Wall Sawing, Wire Sawing
Looking for a Bar & Chain that‌
? r e g n o L s t s a L & r e t Cuts Fas
Look no further‌
RGC has the answer!
RGC now has a complete line of concrete cutting chains and bars that fit most hydraulic and gas chainsaws on the market today. Call RGC for price and availability.
1-800-RGC-TOOL (742-8665)
w w w. CSD A .ORG
sales@rgcproducts.com
c on c r e t e o p e n i n g s | 2 3
CSDA Convention Attendance Up 30
Percent
Olathe, Kansas and Jack Sondergard, Central Concrete Cutting, Inc., Edgar, Wisconsin. Douglas Walker, outgoing president, turned the gavel over to Jim Dvoratchek, the newlyelected president. Judith O’Day, Terra Diamond Industrial, Salt Lake City, Utah, now serves as Vice President while Mike Orzechowski, DITEQ Corporation, Lee’s Summit, Missouri, takes up the role of Secretary/Treasurer. Walker will serve as Past President for the next two years and Patrick O’Brien continues to serve as Executive Director of the association. Top row (from left to right): Roger Allen, Kevin Warnecke, Kevin Baron, Tim Beckman, Steve Garrison, Donna Harris, Doug Walker (Past President) Bottom Row: Mike Orzechowski (Secretary/Treasurer), Jack Sondergard, Jim Dvoratchek (President), Kellie Vazquez, Judith O’Day (Vice President), Ty Conner, Patrick O’Brien (Executive Director), Larry Liddle.
Attendance rose an impressive 30 percent from last year’s convention as contractors and
one-on-one with contractors in a more intimate and informal manner than large trade shows.
manufacturers from the concrete sawing and
New products and services from exhibitors
drilling industry gathered in Bonita Springs,
sparked much interest from attendees, and led
Florida, from March 8 to 12 for the 39th Annual
to sales. First-time Tech Fair exhibitor Markus
Concrete Sawing and Drilling Association (CSDA)
Bartl of Expert Equipment Company in Houston,
Convention and Tech Fair. Included in the large
Texas, was pleased with the event. “It turned
number of attendees were new members, first-
out to be a very successful exhibition, as I was
time attendees and many past presidents of the
able to connect with many leading professionals
The CSDA Lifetime Achievement Award
association.
in the industry from all over the country. What
was presented to Past President Ron Van Zee
CSDA President Jim Dvoratchek (right) with Lifetime Achievement Award winner, Ron Van Zee.
A keynote presentation was given by Clint
surprised me was the friendly and cordial
of Diamond Concrete Sawing, Grand Rapids,
Longenecker, Ph.D., entitled The Two-Minute
relationship between exhibitors—even among
Michigan, for his outstanding contribution to
Drill, a leadership practice based on American
direct competitors. More importantly, however,
the association and the industry as a whole.
football. Longenecker’s presentation was well
I took orders.”
Douglas Walker, outgoing president, turned the
received and some CSDA members are already
CSDA Board members were elected at the
gavel over to Jim Dvoratchek, the newly-elected
taking steps to implement The Two-Minute Drill
convention and include Roger Allen, Diamond
president. Dvoratchek is the first contractor to
into their businesses. “I was so inspired by the
Tools Technology, Buffalo Grove, Illinois; Ty
hold the position of president twice for a two-
seminar that I could not wait to get back to
Conner, Austin Enterprise, Bakersfield, California;
year term. Steve Garrison also held the position
the office and use some of the tools that were
Mike Greene, Greene’s, Inc., Woods Cross, Utah;
twice when the association elected a new
provided. I learned that it is important to have
Larry Liddle, Diamond Products, Elyria, Ohio;
president every year. Jim previously served as
solid leadership, a good plan and consistent
Kellie Vazquez, Holes Incorporated, Houston,
president from 1999-2000 and now will serve
follow-through in order for any change to
Texas and Kevin Warnecke, ICS, Blount Inc.,
until March 2013. Outgoing members of the
work,” says Paul DeAndrea of DeAndrea Coring
Portland, Oregon. These Board members will
CSDA Board of Directors were also recognized.
& Sawing, Inc. in Henderson, Colorado.
serve a two-year term, expiring in 2013.
The members and staff of CSDA will now
Concrete cutters, and manufacturers who
Returning for the second year of their
turn their attention to planning the 2012
supply contractors with diamond tools, came
term are Kevin Baron, Western Saw, Inc.,
Convention in Maui, Hawaii, which will mark the
looking for ways to improve and grow their
Oxnard, California; Tim Beckman, Cutting Edge
association’s 40th anniversary. That convention
businesses as signs of an economic recovery
Services Corp., Batavia, Ohio; Steve Garrison,
is scheduled for March 7-9, 2012 at the Sheraton
begin to appear. The number of exhibitors at the
Hilti, Inc., Santa Fe Springs, California; Donna
Maui. For more information, visit www.csda.org,
CSDA Tech Fair also increased from 2010, with
Harris, Concrete Renovation, San Antonio, Texas;
call the CSDA office at 727-577-5004 or email
Thepercent contractormore cut and removed 36on concrete measuring 25Rapper, feet long.Husqvarna Construction Products, 24 companies hand troughs to meet Ron
2 4 | JU NE.1 1
info@csda.org.
Discussions were held on the subjects of Dispatching, Concrete Eco-Practices and LEED Certification and Hiring Practices in the Sawing and Drilling Industry. The proceedings from these roundtables have been transcribed and are now available to download through the Members Section of the CSDA Website. Dispatchers are an integral part of every contractor company’s day-to-day operations, often asked to handle multiple responsibilities.
www.expertequipment.com
The Concrete Sawing and Drilling Association (CSDA) has available the proceedings from the three roundtable discussions held during the CSDA 2011 Convention and Tech Fair.
Cardi TP 400-EL 16" - 6" Deep
Cardi T1 PU-EL 3-Speed
Slider EZ Release Ring
and areas for improvement. Topics included
Cardi T3-250-EL 2-Speed
Cardi T6-375-EL 3-Speed
!
NEW Roller Carriage 2-7/8" HDX
L 180
Cardi Vortex 625 6-Speed
Cardi BM 800-EL 3-Speed
Cardi BM1000-EL 4-Speed
Cardi T9-450-EL 4-Speed
Cardi FR 302 3-Speed
S A L E S • PA R T S • S E R V I C E
The Dispatching roundtable addressed a dispatcher’s typical responsibilities, challenges
Cardi T2-220-EL 3-Speed
CALL 713-797-9886
www.expertequipment.com
Roundtable Transcripts Available
w w w. e x p e r t e q u i p m e n t . c o m
technology, effective techniques, customer service, equipment location and “dispatcher survival techniques.”
C.O.ExpertEquipAd10.indd 1
1/13/11 2:07 PM
In order to stay competitive in today’s market, many concrete cutting companies
The selection of new employees is one
on what methods contractors use in the hiring
have added new services. One of these services
the most important decisions a contractor can
process and how companies can reduce the risk
is concrete and slurry recycling, which has
make. Although there is no foolproof way of
of selecting the wrong person for the job
become a hot topic in recent months with an
guaranteeing a 100% success rate when hiring,
Roundtable discussions are available on the
increasing focus on “green” concrete practices.
contractors can increase their odds significantly
CSDA Website. For more information, contact
Discussions from the Concrete Eco-Practices and
by planning and setting out proper criteria
the CSDA office at 727-577-5004 or email
LEED Certification roundtable covered how
through each stage of the hiring process.
russell@csda.org.
LEED credits apply to cutting companies and
Discussions during the Hiring Practices in the
how contractors can use recycling services to
Sawing and Drilling Industry roundtable touched
increase profit. w w w. CSD A .ORG
c on c r e t e o p e n i n g s | 2 5
Back in the Saddle
Jim Dvoratchek Takes the Reins of CSDA Once More
to make his business a success and he had the energy to dive in. “From the beginning, I saw tremendous value in networking with industry leaders,” says Dvoratchek. “I sought knowledge, and the members of CSDA were willing to openly share their knowledge with me.” Hard Rock began to grow, as did his involvement with CSDA. He was able to implement the things he was learning into his business and share his own ideas with other members of the association’s Board and committees. This participation coupled with additional years in business helped him to gain much knowledge, forge important business relationships and form strong friendships—all things that can help any young business leader. Now that Hard Rock had developed into a large-scale operation, and now that Dvoratchek is working on a business succession plan with a Jim Dvoratchek (second from the right) with his wife Jeanine (center), son-in-law Ryan Hammer (left), daughter Emily Hammer (second from the left) and son Michael (right).
E
trusted team, including some of his children, he now feels he has the time and resources
arlier this year at the Concrete Sawing
and has, once again, committed his time and
to commit to the position of president. For
& Drilling Association’s 39th Annual
energy to the office. But it is now a much more
some, this may have been the perfect time
Convention, Jim Dvoratchek, owner
seasoned professional taking the reins of the
for a guy like Dvoratchek to slow down and
of Hard Rock Concrete Cutters, Inc. of
association to give back to the industry that has
reap the benefits of his years of hard work, but
Wheeling, Illinois, was elected president. It was
meant so much to him. The fact that contractors
experience, especially in the past few years, has
no surprise to members since Dvoratchek held
fill offices in industry-wide associations does, in
taught everyone that it is not enough to rest on
the position of vice president for the previous
many ways, relate to the life cycle of their own
their laurels anymore.
two years, and the vice president assumes
businesses.
Next year marks the 40th anniversary of
the position of president. However, it was a
In 1979, he began his career in concrete
CSDA. Many of the industry leaders who helped
milestone for the association and Dvoratchek
cutting as a helper/laborer before becoming an
grow the association in its infancy and make
as he became the first person to be re-elected
estimator and cutter with the Concrete Sawing
it such a valuable organization are now ready
to the position for a two-year term.
& Drilling Company. He then co-founded Hard
to step aside from the day-to-day operations
Dvoratchek was first elected president of
Rock Concrete Cutters, Inc. in 1987. He served
of their own companies and help new leaders
CSDA in 1999, twelve years ago. At that time,
as secretary/treasurer for the new business and
develop. In Jim Dvoratchek, the association has
he had been in the industry for 20 years and
then moved to president, a position he still holds
a proven leader who has returned to help the
was busy growing his company in the highly-
today. In 1995, Jim also helped to co-found and
association continue moving forward. He is a
competitive Chicago market. He was also a
serve as president of Hard Rock Company of
great example of the kind of people who make
founding member of the CSDA Insurance
Wisconsin and held the position of secretary/
up the membership of CSDA. The association is
Program, which took quite a lot of time to
treasurer for Central Illinois Concrete Cutters, Inc.
fortunate to have dedicated people who are
administer but he felt the time was right to
At the time Jim joined CSDA, he was keen to
willing to get back in the saddle and continue
commit his own time and energy to the office.
learn from other cutters about concrete cutting—
Now Dvoratchek has been in the concrete
techniques, applications and equipment. He
sawing and drilling industry for over 30 years
knew that he needed this kind of knowledge
2 6 | JU NE.1 1
to steer it in the right direction.
w w w. CSD A .ORG
c on c r e t e o p e n i n g s | 2 7
CORE HEALTH
Nutrition for Job Performance By Erin O’Brien
H
ealthy diet, superfoods, low-fat, high-protein and counting carbs— all buzzwords we have heard on
television, read in books, magazines and on the Internet. There is a wealth of information concerning nutrition out there that, at times, can seem conflicting and often confusing. So who is right and what is really important when it comes to eating a healthy diet and what impact does this have on your job performance? The answers may surprise you. While healthy nutrition can be a confusing subject, the basics are not. Yes, there are fad
Protein is responsible for building and
While every person is different, the same
diets and extreme weight-loss plans that may
repairing muscles, ligaments, tendons and
general principle applies. If more calories are
work for some, but the easiest way to eat
other tissues. Protein is not a significant energy
consumed than burned, the person will gain
healthy is by following a simple plan that will
source, and excess protein will be stored as fat.
weight. If more calories are burned than con-
not only make your body healthier, it will also
Fats are a concentrated energy source and
sumed, the person will lose weight. Younger
improve your mood, raise your energy level
are also used for cell function, protection of
and active people will require more calories
and keep you healthy. All of these elements
vital organs, supplying essential fatty acids and
daily, while older and sedentary individuals
contribute to better job performance.
are used to transport vitamins throughout the
will require less. In general, men will need
bloodstream. There are three main types of
to consume more calories than women. See
fats: trans, saturated and unsaturated.
Figure 1 for more information about daily
People who consistently eat a healthy diet—not just cutting calories—reduce their risk of cardiovascular (heart) disease, cancer and other diseases and infections. Body weight
•
the cooking process, often by frying,
is often lower, reducing stress on muscles and
and should be avoided as they raise
joints and healthy eaters fatigue less easily. A healthy diet also contributes to an efficient immune system and better overall health.
Trans fats are usually added during
triglycerides and LDL (bad) cholesterol. •
Saturated fats from meat, dairy and some oils also increase cholesterol and
The basics of a healthy diet are made up of
therefore risk of heart disease. They
five main components: carbohydrates, protein,
should be consumed sparingly.
fats, vitamins and minerals. Carbohydrates are
dependent on each individual, their age and activity level. Men typically need more protein than women, while active individuals will need more carbohydrates than sedentary people. A healthy diet always starts with a good breakfast. Job performance will suffer if breakfast is an afterthought and comes in a greasy bag from a fast food restaurant. Breakfast
The two types of unsaturated fats, mono
should be high in carbohydrates for energy
two types: simple and complex. Simple car-
and poly, are considered “healthy” fats
and high in protein. This helps keep hunger
bohydrates give the body short, quick bursts
and lower cholesterol levels and raise
at bay until lunchtime. Easy healthy breakfast
of energy and come from foods like fruits,
HDL (good) cholesterol. Polyunsaturated
options include: oatmeal with fruit, whole-
juices and milk. Complex carbohydrates have
fats come from vegetable and fish oils,
wheat toast with peanut butter and jelly or an
the ability to be stored in the body for longer
while monounsaturated fats come from
English muffin with peanut butter. Fruit juice
periods of time to be used as energy. Examples
olive oil, peanut oil, avocados and most
or milk is a good beverage option.
of complex carbohydrates are whole grains,
nuts.
the body’s fuel source and are made up of
•
caloric intake. Again, these percentages are
Lunches and dinners should include a high
pasta, bread and vegetables. All forms of car-
Vitamins and minerals provide no energy,
percentage of protein, some carbohydrates,
bohydrates are broken down by the body into
but are important components that help sup-
and lots of fruits and vegetables. Lunch needs
glucose, which is then converted into energy.
port the body’s essential functions.
to keep you full until dinner, so protein is a
2 8 | JU NE.1 1
Caloric Intake Carbohydrates
Protein
Fats
Active Males
2,400–3,000
45–65%
25–35%
20–35%
Sedentary Males
2,200–2,800
45–60%
20–30%
20–35%
Active Females
2,000–2,500
45–65%
20–30%
20–35%
Sedentary Females
1,600–1,800
45–55%
15–25%
20–30%
EQUIPMENT DEVELOPMENT CO., INC.
INTRODUCING OUR NEW LINE OF HAND HELD CORE DRILLS
Figure 1. Daily caloric intake and nutrient recommendations. Numbers will vary due to age, activity level and individual specifics.
priority. A reasonable amount of carbohydrates
•
should be added to give you energy. Lunch is also an easy place to add fruits and vegeta-
Fish—especially salmon, mackerel and herring, which all contain omega-3 fats
•
Cooking oils—olive, sunflower, peanut
bles, possibly with an apple and peanut but-
and sesame oils all contain high levels
ter or carrot sticks and hummus. Dinner could
of monounsaturated fats, which lower
include anything grilled (chicken, pork or fish)
cholesterol, and vitamin E, which lowers
and a serving of vegetables, such as a salad or
LDL (bad) and raises HDL (good) levels
steamed vegetables. Dinner should be light on fats and heavy sauces or dressings.
•
and lycopene, all of which lower the risk
The term “superfoods” is used frequently, but with good reason. It usually describes foods that are not only healthy, but also contain an
of developing cardiovascular disease •
choy all contain folate (a mineral) which
be included in your diet as much as possible.
•
•
• •
Black beans—low in fat and packed with
and omega-3 fats which decrease
vitamin A, vitamin K and sulforaphanes,
triglyceride levels as well as contain
which protect against stomach, lung and
monounsaturated fats, which decrease
breast cancers
LDL levels and raise HDL levels Eating a healthy diet does not need to
protects against viruses, infections and
be complicated, expensive or time-consum-
cancers
ing. The best plan is to take one step at a
Kiwi—the most nutritionally dense fruit,
time, gradually making a permanent lifestyle
contains many vitamins and minerals
change. The benefits of improving your health
Mackerel—high in heart-healthy omega-3 Pork tenderloin—low in fat and calories, Swiss chard—similar to spinach, high in vitamins A and K
•
Nuts—peanuts, cashews, almonds, walnuts and others all contain fiber
high in vitamin B6 •
•
Broccoli rabe—low in calories, high in
Green tea—high in antioxidants and
Walnuts—high in omega-3 fats Anyone will benefit from a heart-healthy
diet that includes whole grains (providing fiber which lowers cholesterol), healthy fats (monounsaturated and omega-3) and lots of fruits and vegetables. Here are some examples of heart-healthy foods:
w w w. CSD A .ORG
1 Speed Very easy to use and lightweight
3 Speed Best 3 speed core drill on the market, 25% more power then the leading competitors
Most powerful hand held core drills in the industry. Lightweight,Compact and easy to use even for beginners
CALL ABOUT OUR DRILL STANDS MANUFACTURED PROUDLY IN THE USA
decreases heart disease risk
fiber and protein
fats (good fats) and low in mercury •
Dark, leafy greens—spinach, kale, greens, arugula, Swiss chard and bok
abundance of nutrition. These foods should
•
Fruits—contain fiber, phytochemicals
Can Plug into a regular Household Outlet, Capable of Wet or Dry Drilling using a Standard Waterhose, Compatible with Standard Core Bits, One Year Limited Warranty on Motor
far outweigh any negatives, such as extra time or money spent in the long run. If the result is improved job performance, better quality of life and longer life, any extra effort is worth the payoff. Erin O’Brien, MS, ATC is a Certified Athletic Trainer and Marketing Coordinator for O’Brien International, the association management company that manages the Concrete Sawing & Drilling Association. O’Brien received her Bachelor of Science degree in Athletic Training from Ohio University and her Master of Science degree in Applied Physiology and Kinesiology from the University of Florida. She is a regular contributor to Concrete Openings magazine. She can be reached at erin@csda.org or 727-577-5002.
1-800-638-3326 • edcoinc.com contrxsystems.com
Do you “Like” CSDA? CSDA is on Facebook, and we hope you “like” it! The CSDA page is packed with all the latest news, updates, photos and videos from the association and Concrete Openings magazine. Look out for exclusive content and become “friends” with others who are looking to network and promote the sawing and drilling industry. Join our growing fan base and stay in touch with the association through your PC, laptop or mobile device.
c on c r e t e o p e n i n g s | 2 9
The Business of Business
Ten Ways to Cut Fuel Costs By Jack Lee
R
emember the good old days, when prices at the pump were below two dollars per gallon and usually stayed there? Well, the good old days are gone and today the world is a place where fuel prices seem to change by the hour. Now pundits speculate on living with oil prices running as high as $200 a barrel. Many consumers have adjusted their lifestyles. Some try to drive less or have chosen to carpool, while others have traded their gas-guzzlers and opted for more fuel-efficient vehicles, including hybrids. For companies, the good old days meant simply having employees fuel up and head out to the job. Little attention was paid to managing fuel. In the past year, the high price of oil is cutting deeper than ever into company profits, causing owners and managers to adopt a new fuel consciousness. Fuel management is a necessity.
You can’t control the price of fuel, but
costs. Allowing an engine to idle more than
you can control your fuel consumption.
three minutes causes expensive damage, harms
The answer is fuel management.
efficiency, shortens engine life and increases
Any company can improve its fuel efficiency. It takes work and commitment, from personnel in the head office to employees on the road and at the job sites. More and more companies are now making changes in oper-
can initiate a campaign to reduce idling time and reward participants if their fuel consumption drops. 3) Start Off Slower
ating practices to cut costs and be prepared
This is another lesson that some drivers
for even higher costs in the future. To help
must learn. Accelerating aggressively from
contractors adjust to these historic fuel prices,
standing starts wastes fuel and saves less than
here are ten ways to cut fuel costs.
three minutes of driving time per hour. It can
1) Train and Educate Drivers This starts with the people who have their foot on the gas pedal. Drivers can control fuel consumption each time they fire up their engines, and proper training can improve
even result in using 40 percent more fuel and increase toxic emissions by 400 percent! Drivers should be encouraged to ease up on the gas pedal to increase efficiency. 4) Slow Down
fuel efficiency, economy and emissions. Hard
Driving at excessive speeds is not only
acceleration, speeding and idling are the big-
dangerous but it also wastes fuel and creates
gest causes of fuel waste. Companies can ini-
higher levels of toxic emissions. Speeds over
tiate a training course for drivers and reward
60 miles per hour drastically impact fuel effi-
participation.
ciencies while vehicles traveling at 75 miles per
2) Decrease Idling Drivers should be aware of the length of time that engines idle. Machinery and equipment should no longer be left running all day long. Excessive idling can add to fuel costs by as much as 50 percent and can shorten the life of engine oil by 75 percent, adding more
3 0 | JU NE .1 1
maintenance costs. It all adds up. Companies
hour can use 20 percent more fuel than those traveling at 60 miles per hour. Trucks traveling at 75 miles per hour use 50 percent more fuel than those traveling at 60 miles per hour and they also emit 100 percent more carbon monoxide, 50 percent more hydrocarbons and 31 percent more nitrogen oxides.
5) Lose Weight
cient and perform better with modern diesel
10) Implement Advanced Mobile Asset Management Technology
Excess weight places unnecessary strain on
fuels such as ultra-low sulphur diesel and bio-
a vehicle’s engine and greatly affects its fuel
diesel. Though it may seem expensive, new
There are a growing number of businesses
efficiency. By removing as little as 100 pounds
diesel vehicles can save thousands of dollars in
that can supply this technology. Companies
of weight from a car or truck, drivers can sig-
maintenance, fuel and productivity per vehicle.
can measure and manage fleets better when
nificantly improve the vehicle’s gas mileage.
It is good practice to measure each piece of
the right information is made available.
Companies should encourage drivers to check
equipment for fuel efficiency and get rid of
Tracking miles traveled, average speed and
their vehicles and remove any unnecessary
those that are not performing well.
engine efficiency is very important in cutting
weight. This can include tools and equipment that will not be required for the day’s work. 6) Use a Fuel Management System
8) Tune-up Vehicles Regularly Companies should employ a stringent, well-managed maintenance policy. Unfor-
This is the most powerful way to lower
tunately, too many companies adopt a “fix it
fuel costs and increase productivity. Available
when it breaks” attitude. A well-maintained
systems range from basic onsite refueling,
vehicle performs better, improves fuel
which saves up to 20 minutes in wasted
efficiency, reduces toxic emissions and, in the
time and fuel each day, per vehicle, to
long run, costs less to maintain.
automated fuel tracking that details every
9) Pump it Up
gallon pumped into every vehicle by date, time, quantity and fuel type to telematics, which measures overall fuel efficiency, vehicle performance, tracks fuel waste due to idling and speeding. It also identifies critical areas to improve efficiency and reduce fuel costs and emissions. The technology exists so that companies can accurately track and monitor fuel consumption, one vehicle at a time. 7) Upgrade the Fleet Whenever possible, companies should invest in modern, fuel-efficient vehicles. Modern diesel engines are far more fuel-effi-
w w w. CSD A .ORG
fuel costs. This information will help drivers and dispatchers optimize routes with better planning. Mapping software and GPS will eliminate thousands of unnecessary miles per week. Less time on the road means less fuel consumed, less wear on vehicles, decreased expenditures and overall increased productivity, plus lower toxic emissions. Once a company commits totally to managing its fuel usage better and drivers are
Proper tire inflation improves gas mileage.
encouraged to cut out some of their bad fuel
Statistics show that improperly inflated tires
habits, positive results will follow. The goal
can cost up to two weeks worth of fuel per
is to then have everyone stick with this new
year. Employers should take this statistic and
approach since there is a good chance that
apply it to the number of trucks in their fleet.
fuel prices will only continue to go up.
Two weeks per year per vehicle can add up to thousands of dollars in lost profits. In addition, proper tire inflation results in improved vehicle and braking performance, and increases tire life.
Jack Lee is the President and CEO of 4Refuel Canada, Inc. based in Langley, British Columbia. The company is one of North America’s fastest growing fuel logistics businesses, and Lee distributes regular articles on fuel management through a series of “Ask the Fuel Expert” documents. He can be reached at 606-513-0386 or email askthefuelexpert@4refuel.com.
c on c re t e o p e n i n g s | 3 1
Explore how to work smarter at the new www.husqvarnacp.com
Husqvarna introduces its newest remote-controlled demolition robot, the DXR 140.
3 2 | JU NE.1 1
Husqvarna Construction Products has launched a new website! It is easier to navigate and enables you to find exactly the right information - from technical specs to innovative products and accessories, we have it all. The website features an interactive tool guide to help find the perfect blade/bit for any project and the FAQ pages enable you to troubleshoot through various situations. Upgrades have also been made to the equipment pages with additional specs and detailed information as well as matching diamond tools and other related products displayed at the bottom on the page. This provides you with all the information on one page. You can also compare equipment to find the right one for your needs. Another important feature is a new ‘innovations’ tab that highlights various technological developments by Husqvarna that sets our equipment apart from competitors. Check out the new website and see how you can work smarter. HUSQVARNA CONSTRUCTION PRODUCTS w w w. CSD A .ORG
Can’t wait to check it out? Scan the code with your smartphone and see for yourself! c on c r e t e o p e n i n g s | 3 3
17400 West 119th Street • Olathe, Kansas 66061 • T 800-288-5040 • F 800-825-0028 2077 Bond Street • North Bay, Ontario P1B 8J8 • T 800-461-9589 • F 800-728-1907 www.husqvarnacp.com Copyright © 2011 Husqvarna AB (publ.). All rights reserved. Husqvarna is a registered trademark of Husqvarna AB (publ.).
Port of Tampico
Berthing Structure Removed with Wire Saw
A berthing structure required removal at the Port of Tampico.
W
hen the support pillars of a large concrete berthing structure at a major Mexican shipping port began to corrode, the authorities contacted a professional cutting contractor to demolish and
remove the platform. This work was to be done quickly, before the support pillars gave way and allowed the structure to fall into the water, which would create a hazard for passing ships. The Port of Tampico is situated on the East Coast of Mexico in the state of Tamaulipas. Tampico was founded in 1554 and the city was declared an official deep-sea port in 1824. Today, the port has over 20 large docks in public and private shipping terminals, some of which can handle up to 50,000 tons of cargo that arrives by ship from the Gulf of Mexico. The total distance of these docks and terminals is over 4,000 linear meters (13,123 feet). The decaying concrete berthing structure measured 6 meters long, 6 meters wide (19.7 feet) and stood 2.2 meters (7.2 feet) tall from the base of the port’s sea bed. The 0.7-meter-thick (2.3-foot) berthing platform was supported by eight 61-centimeter-diameter (24-inch) steel
3 4 | JU NE.1 1
CONCRETE
CASES
The structure was cut into nine sections using diamond wire cutting techniques.
Core holes were drilled for wire saw runs and for crane rigging.
w w w. CSD A .ORG
pillars filled with reinforced concrete. Some
by those involved in this project,� said Raul
of the corroded pillars had crumbled, and the
Bracamontes, owner of ADRA.
decreased support in these areas had caused
The contractor decided that this job would
others to break, due to the shift of balance
also be well suited for cutting with diamond
and weight.
wire, as completing work in the water and
In September 2010, the Universidad del
around such a busy waterway as the Port of
Carmen (Carmen University) collaborated
Tampico would require minimal noise and
with PEMEX of Central Mexico to set up a
vibration. This technique would also create
project to remove the platform and some
far less debris than traditional demolition
of its pillars. The university enlisted the
methods. A plan was drawn up to cut the main
help of CSDA member Soluciones Tecnicas y
concrete platform into nine pieces and retain
Profesisonales ADRA S.A. de C.V. (ADRA) of
two of the support pillars for testing. The
Leon, Mexico, to cut sections of the concrete
cutting work was scheduled to be completed
structure and retain some of the pillars to test
15 days from commencement, so time and
their structural integrity and define what had
speed were of the essence. In addition, the
caused the pillars to fail. “Our wire saw work
team from ADRA had to factor in the structural
at the collapsed Tonola Bridge (featured in the
decline of the berthing platform and pillars.
September 2010 issue of Concrete Openings)
The sections of concrete had to be removed
enhanced our reputation and was noticed
in such a way as to not disturb or collapse the remaining structure.
c on c r e t e o p e n i n g s | 3 5
After all nine specified sections of the concrete platform were cut and removed, the team from ADRA turned their attention to the 2-foot-diameter pillar structures. The task involved cutting and removing two pillars and transferring to land, where they were to be cut into three pieces to evaluate their internal structure. This would help the customer understand what failings had taken place and how to guard against further breakages on other structures. To remove the pillars, ADRA first used a diver to extract hard mud from around the bases. This eliminated friction between the soil and the pillars. The pillars were then extracted from the water by crane and laid out on land. Operators then used a Husqvarna K1250 gas-powered hand saw with a 16-inch-diameter blade to cut the pillars into smaller sections. The main safety concern for Bracamontes and his team was the busy location and crumbling condition of the berthing structure. The extent to which the structure was decayed A Husqvarna CS2512 wire saw cut through the structure.
was not fully known, and so constant checking of its integrity was performed to guard
To begin the cutting work and prepare the wire saw setup, the contractor used a Hilti DD200 core drill with a 6-inch-diameter core bit from Husqvarna to create eight holes 0.7-meters (2.3feet) deep in the concrete platform. These holes would allow the diamond wire to pass through to set up runs for the wire saw and allow crane straps to be fastened around the sections once cut free. The core drilling of the berthing platform took one operator eight hours to complete. A 5,500-watt generator was used to supply power while water was supplied by a submergible pump with a 0.5-inch hose. Once the structure had been core drilled, the cut lines for the sections were marked out and the wire saw was set up. The Husqvarna CS2512 unit was anchored to the concrete and pulleys were set in place to create the wire runs. Power was supplied by a 125-kilovolt amperes generator and two electric pumps connected to one hose provided water to cool the wire during cutting. A diver was sent into the water to pass the wire around the underside of the structure, and also to inspect the structure and its support pillars. If any rebar was found to be obstructing the diamond wire run, the diver would return to the water immediately and remove the rebar with a cutting torch. The contractor made a cut 6 meters (19.7 feet) in from the edge of the 0.7-meter-thick (2.3-feet) platform to get the first concrete section free. The first piece to be cut free weighed 15 tons and was removed by a 40-ton crane. Wedges were set in place as cutting progressed, and after the first section was removed, the remaining structure was inspected for stability. This process was repeated for each of the nine concrete sections removed. It took the wire saw five hours to cut free one section.
3 6 | JU NE.1 1
The first part of the platform to be cut free weighed 15 tons.
CONCRETE
CASES
REVIEW AND COMMENT ON THIS ARTICLE AT: WWW.concreteopenings.com/FORUM.CFM
Decayed pillars were removed from the water and cut into sections for testing.
Company Profile
against any sudden breakages or collapses. The
To complete the cutting work and save
job was planned to cut nine separate pieces
the corroded berthing structure from collapse,
Soluciones Tecnicas y Profesionales
free rather than one large chunk. The Port of
ADRA used a DD200 core drill from Hilti with a
ADRA S.A. de C.V. began operations
Tampico continued to allow ships to pass by
6-inch-diameter core bit from Husqvarna. The
in 2005 and has been a CSDA member
the cutting area, so care had to be taken to
35-meter (114.8-foot) length of 10-millimeter-
for four years. ADRA is based in Leon
make sure no debris or dust from the work
diameter (0.4-inch) diamond wire and CS2512
Guanajuato, Mexico, and specializes
interfered with these vessels.
wire saw were also supplied by Husqvarna,
in all elements of wire sawing, wall
In addition to these conditions, the
along with one K1250 hand saw. The contrac-
sawing, flat sawing and core drilling.
contractor had to keep one eye on the skies.
tor cut 25.2 cubic meters (889.9 cubic feet) of
Resources
During the work, Hurricane Karl touched down
concrete from the structure’s platform and
General Contractor:
in Veracruz, just south of Tampico. This category
cut through two 2-foot-diameter steel pillars
Universidad del Carmen
3 hurricane did not directly affect the port, but
filled with reinforced concrete. Before this,
CSDA Member:
its strength was enough to cause strong winds
eight holes were drilled 0.7 meters (2.3 feet)
Soluciones Tecnicas y Profesionales
in excess of 75 miles per hour and heavy rainfall
deep and 6 inches in diameter for the diamond
ADRA S.A. de C.V.
(12.7 to 25.4 centimeters or 5 to 10 inches) in
wire runs and for attaching straps. This whole
Leon Guanajuato, Mexico
the Tampico area and delay the cutting work.
process took 10 work days to complete.
Phone: 52-4772 122 797
Working around a large expanse of water on
“The project did have certain risks, but we
a broken structure meant that all members of
planned the work well and made the right
Email: rbracamontes@adra.com.mx
ADRA’s cutting team had to be aware of all
decisions,” said Bracamontes. “The customer
Website: www.adra.com.mx
safety procedures and wear the appropriate
is now considering us for the removal of more
personal protective equipment.
concrete structures at the port in 2011 as they like our system,” he added.
w w w. CSD A .ORG
Methods Used: Wire Sawing, Core Drilling
c on c r e t e o p e n i n g s | 3 7
Cutting Close to Home Core Drilling at the CSDA Offices
W
ith all of the Concrete Openings job stories that are submitted from around the world, it was a pleasant surprise to cover a job taking
place just three floors down from the CSDA office.
The work was to be performed after 5:00 PM when most employees in the building had left for the day. The building contractor, Masters Construction and Development of Tampa, Florida, had previously used a jackhammer for similar jobs but had learned that diamond drilling would be a better alternative for this job. This application would provide less noise and vibration.
Back in March of this year, a memorandum arrived at the CSDA office in
True Line worked with Masters to scan the floor slabs for obstructions
Clearwater, Florida, stating that some construction work would be taking
before starting the drilling work. All three holes were drilled without
place the following day. More specifically, core
problems and within the three-hour time slot
drilling. It turned out that the drilling work was
specified. This allowed plumbing contractors
being performed by CSDA member True Line
to enter the building the following day and
Coring & Cutting of Tampa, Inc.
install the necessary pipe work. The contractor
The second floor of the six-story, 80,445-
used a 20-amp Core Bore motor and M-1 drill
square-foot office building was being remodeled
rig from Diamond Products to complete the
to accommodate new tenants. As part of the
core drilling tasks.
work, an upgrade was required to the floor’s
This is a good example of a typical CSDA
restrooms that would also make them compliant
contractor job that brings in revenue, builds
with the Americans with Disabilities Act (ADA).
solid reputations and often leads to more work
Vent stack piping was to be re-routed and
for many companies.
connected to the water and sanitary lines in the
CSDA has produced Best Practice docu-
ceiling of the first floor. It was specified to core
ments on the subjects of Diamond Cutting
drill two 5-inch-diameter holes—one through
Tools for ADA (CSDA-BP-005) and Ground
a 5-inch-thick concrete floor slab and the other
Penetrating Radar for Concrete Scanning
through a 12.5-inch-thick slab. In addition, one
(CSDA-BP-007). To view these documents and
3-inch-diameter hole was also to be created
other Standards, Specifications, Best Practices
through the 5-inch-thick slab.
and Tolerances, visit www.csda.org and click on the link under Architect/Engineer Resources.
3 8 | JU NE.1 1
WHEN THE SIZE IS NOT A PROBLEM!
“ … with its 20 mm in diameter it can make very large cuts, it’s very helpful when we have to do particular jobs. Unique.,, Francesco, Italia
“… if we cut steel we have no problems using this electroplated diamond wire with conical beads.”
Adam, New Zeland
“… cutting concrete and reinforced concrete it has become simple, the only problem we have is to choose between cutting speed or tool’s life.”
Yuri, Ucraina
“… contingencies are always around the corner, but if we have the right solution we can rest quiet. With the thin wires it’s all much simpler.”
Mark, Holland DIAMOND PAUBER srl Via Aprilia, 5 - 54100 Massa (MS) Italia - t +39 0585 830425 - f +39 0585 830000 pauber@diamondpauber.it - www.diamondpauber.it w w w. CSD A .ORG
c on c r e t e o p e n i n g s | 3 9
Safety CountS
New OSHA Guidance on Employee PPE By Mark A. Lies II and Elizabeth Leifel Ash
S
ince 1974, OSHA has had regulations
whether the following hazards to employees
•
The limitations of the PPE
in effect that required employers to
may be present:
•
The proper care, maintenance, useful life
provide personal protective equip-
•
Hazards of process or environment
ment (PPE) to employees as protection for
•
Chemical hazards
•
Radiological hazards
employee to demonstrate to the employer
•
Mechanical irritants
that the employee understands what has been
eyes, face, head and extremities, including protective clothing, respiratory devices and protective shields and barriers. In addition, the employer was required to ensure that employees used the PPE when exposed to the hazard and that the PPE be maintained in a sanitary and reliable condition so that it would function as intended. Throughout the history of
It should be determined if any of these items are likely to be encountered in the workplace in a manner capable of causing injury or impairment to the body. This injury or impairment can be through the following:
these regulations, there have been ongoing
•
Absorption
disputes between employers and OSHA over
•
Inhalation
which specific PPE the employer would be re-
•
Physical contact
quired to provide at no cost to the employee.
This assessment requirement has
This article discusses new guidance issued by
existed since 1994 and employers
OSHA on February 10, 2011 that clarifies recent
are already subject to citation
revisions to OSHA’s PPE rules.
for failure to perform it. Many
OSHA issued new rules clarifying the
employers are unaware that
employer’s obligation in 2007 (Federal Register
there is a requirement for
Vol. 72, No. 220, pp. 64342-64430). The final
a written certification that
rule became effective on February 13, 2008
such hazard assessment has
and required implementation by May 15, 2008.
been performed (29 CFR
In February of this year, OSHA issued new guid-
1910.132(d)(2)), which
ance to compliance officers to assist them in
OSHA will request if an
conducting inspections related to PPE. The
inspection is conducted
guidance clarifies what type of PPE employ-
involving PPE compliance.
ers must provide at no cost and sets out the
The organization will cite the
Agency’s enforcement policies concerning PPE.
employer for a violation if this
The guidance can be found at http://www.
certification is not forthcoming.
osha.gov/OshDoc/Directive_pdf/CPL_02-01050.pdf.
Employer Duty to Provide PPE and Training
Employer Duty to Conduct PPE Assessment
Once the employer has completed the hazard assessment,
As a starting point, existing OSHA regu-
the employer must provide the
lations have long required an employer to
PPE to the employee, train the
conduct a hazard assessment to determine
employee in its proper use and
if hazards are present, or likely to be pres-
enforce the use of PPE through
ent, which necessitate the use of PPE (29 CFR
appropriate discipline. This training
1910.132(d)(1)). In this regard, employers are
should include the following aspects:
required to conduct a broad assessment of
•
When PPE is necessary
•
How to properly use, adjust
the various aspects of the job to determine
and wear PPE
4 0 | JU NE .1 1
and disposal of PPE The training should also require the
taught (29 CFR 1910.132(f)(2)). Finally, there is an existing requirement for the employer to generate another written certification that the employee has understood the foregoing training (29 CFR 1910.132(f)(4)). OSHA can issue citations for failure to prepare such certification.
Employer Duty to Pay for PPE Obviously, once the employer has deter-
Cutting professionals are our only focus.
mined that PPE is required, the issue arises over who will pay for it—the employer or the employee. In an effort to finally clarify who pays for PPE, OSHA began rule-making in 1999 which resulted in the ruling that took effect in 2008. The ruling adds a new subpart for each industry sector subject to the rule. For general industry, the new rule is designated as 29 CFR 1910.132(h) – Payment for Protective Equipment. This subpart defines the new clarifications regarding payment for PPE. Importantly, while Section 1910.132 generally relates to PPE, there are other OSHA standards that specifically require PPE, including the blood-borne pathogen standard, the grain handling standard and a host of standards that are specific to regulated airborne contaminants such as lead and asbestos. The regulation generally requires that all protective equipment used to comply with Section 1910.132, including PPE, must be provided to employees at no cost to them. According to the new guidance document, the employer must provide the following PPE at no cost to the employee if used to comply with an OSHA standard: •
Metatarsal foot protection
•
Rubber boots with steel toes
•
Shoe covers like toe caps and metatarsal guards
• •
Non-prescription eye protection Prescription eyewear inserts/lenses for welding and diving helmets
•
Goggles
•
Face shields
•
Laser safety goggles
•
Fire-fighting PPE—helmet, gloves, boots,
Whether in the plants or on the roads, DTT blades can make your job more profitable. DTT’s innovative bond technologies and relentless development efforts will maximize the performance on your next project. Call your salesman today to begin saving money. DiamondToolsTechnology.com 723 Hastings Lane • Buffalo Grove, IL 60089 • 877-3456-DTT (388) DTT_concreteOpenings_ad_Final.in1 1
1/11/11 10:31:54 AM
proximity suits, full gear •
Hard hats
•
Hearing protection
•
Welding PPE
•
Non-specialty gloves
Payment is required if they are PPE, i.e. for protection from dermatitis, severe cuts/abrasions
Payment is not required if they are only for keeping clean or for cold weather with no safety or health consideration
•
Rubber sleeves
w w w. CSD A .ORG
c on c r e t e o p e n i n g s | 4 1
• • •
Aluminized gloves
has the right to require employees to pay for
and secure, as in a locker or locked cabinet, and
Chemical resistant gloves/aprons/
PPE if the employee loses or intentionally dam-
may also require an employee to turn in his or
clothing
ages the PPE (29 CFR 1910.132(h)(5)). This situ-
her PPE at the termination of employment. If
ation will arise when the employee reports to
the employer requires employees to leave non-
work without his or her PPE or the employer
specialty eyewear or non-specialty footwear at
conducts their walkaround of the worksite
the job site, then OSHA has taken the position
and observes that PPE is so damaged and not
that the employer must provide those items at
due to normal wear and tear. The employer
no cost to employees.
can determine if the damage is intentional. At
Potential Citation Liability
Barrier creams unless used solely for weather-related protection
•
Rubber insulating gloves
•
SCBA, atmosphere-supplying respirators for escape only
•
Respiratory protection
this point, the employee cannot be allowed to
•
Fall protection
work unless the PPE is replaced. Furthermore,
•
Ladder safety device belts
the employer can require the employee to pay
•
Climbing ensembles used by linemen such as belts and climbing hooks
•
Window cleaners safety straps
•
Personal flotation devices such as a life
for the replacement PPE and follow its normal disciplinary policies against the employee for losing or intentionally damaging PPE that is company property. It should be noted that if the PPE is dam-
jacket
aged due to normal wear and tear caused by
•
Encapsulating chemical protective suits
job activities or environment, the employer
•
Reflective work vests
must replace the PPE at its cost and the
It is very important to note, however, that
employee is not subject to discipline.
this list is not all inclusive. The employer’s PPE
Employee-Owned PPE
It is important to note that if the agency determines a violation has occurred regarding failure to train employees, properly equip them with PPE or to enforce the use of PPE, the employer faces liability for citations. This liability can be significant if the agency decides to issue citations on a per employee basis, that is, a separate citation with a separate monetary penalty for each employee found out-of-compliance for conditions such as not wearing hard hats, protective eyewear or hearing protection. If a number of employees are found out of compliance, the penalties can quickly multiply
hazard assessment will be the determining
In many instances, employees may vol-
factor for which PPE is required for the job,
untarily provide items which constitute PPE,
Since OSHA is now focusing on PPE com-
thereby imposing an obligation to pay for it
and if so, the employer has no obligation
pliance, employers must now focus on their
upon the employer.
in the thousands of dollars of monetary liability.
to pay for the PPE. However, the employer
compliance efforts, including:
Conversely, the rule and the new guide
must evaluate and determine that this PPE
1. Verifying their initial PPE hazard
identify specific examples of PPE for which the
is at least as effective as that required by the
employer is not required to pay, as follows:
employer’s hazard assessment. If it is not at
•
Non-specialty safety-toe protective
least as effective, the employer must provide
footwear such as steel-toe shoes/boots
the PPE. In addition, any time the employee-
Non-specialty prescription safety
supplied PPE becomes no longer functional,
eyewear
or the employee declines to provide it, the
•
Sunglasses/sunscreen
employer’s duty to provide PPE will become
•
Sturdy work shoes
•
Ordinary cold weather gear such as
•
coats, parkas, cold weather gloves, winter boots
effective. Similarly, an employer does not have an obligation to pay for PPE requested by an employee that exceeds the PPE requirement, as long as the employer provides PPE that meets the standards at no cost to the
•
Ordinary rain gear
employee. Even if an employee elects to use
•
Back belts
upgraded or personalized PPE, however, the
•
Long-sleeved shirts
employer must nonetheless ensure that the
•
Long pants
•
Dust mask or respirators used under the voluntary use provisions in §1910.134 Again, this list is illustrative, and many
other items may be excepted based upon the employer’s hazard assessment. Duty to Pay if PPE Lost or Intentionally Damaged While the employer must pay for required PPE within its hazard assessment, the employer
4 2 | JU NE.1 1
PPE is adequate to protect the employee from hazards present in the workplace, is properly maintained and is kept in a sanitary condition. Off-Site Use of PPE An employer may allow an employee’s PPE to be used off the job site. However, the off-site use of the PPE does not relieve the employer of its obligation to pay for the PPE where required. Where PPE is not required to be worn away from the job site, the employer may require employees to keep PPE on-site
assessment and written certification 2. Confirming employee training on the use of PPE and written certification 3. Developing policies on issuance of PPE, use of employee-supplied PPE, inspection and replacement program for use of PPE and finally, discipline for loss or intentional damage to PPE By taking these steps, employers can limit their risk of OSHA citations and educate employees on the care and maintenance of PPE. Mark A. Lies II is a labor and employment law attorney and partner with Seyfarth Shaw LLP in Chicago, Illinois. He specializes in occupational safety and health law and related employment law and personal injury litigation. In addition, Seyfarth Shaw has assisted CSDA members by holding presentations and moderating roundtable discussions at annual conventions. He can be reached at 312-460-5877 or at mlies@ seyfarth.com. Elizabeth Liefel Ash is an associate with Seyfarth Shaw. Her practice focuses on regulatory compliance and litigation, including occupational safety and health and environmental matters. She can be reached at 312-460-5845 or at eash@ seyfarth.com.
OSHA /CSDA Alliance Latest
CSDA Past President Doug Walker (pictured standing, second from right) with other attendees of the OSHA Alliance Program Construction Roundtable, including Assistant Secretary of Labor for Occupational Safety & Health Dr. David Michaels (standing sixth from left).
T
he Alliance between the Concrete Sawing & Drilling Association (CSDA) and the Occupational Safety and Health Administration (OSHA) is now in its fifth year and continues to educate contractors, prevent on-the-job accidents and injuries and provide vital materials to advance a safe work environment for sawing and drilling professionals. Here is the latest news from the Alliance Program.
Occupational Safety and Health’s Prevention through Design and
Alliance Program Construction Roundtable
construction safety design solutions that address beam columns, fixed
Discusses OSHA Compliance Assistance Products
ladders and stairways. These designs focus on solutions that will help
National Occupational Research Agenda initiatives. In addition, Mary Watters, Director Communications Department, CPWR - The Center for Construction Research and Training, gave an overview of the Electronic Library of Construction Safety and Health, which is a collection of free information on construction safety and health in English, Spanish and other languages. In addition, members of the group provided feedback on drafts of product ideas that were developed at the last roundtable, including
More than 20 representatives from 14 Alliances, including CSDA Past
prevent falls in the construction industry. The group previously completed
President Doug Walker of Atlantic Concrete Cutting, Inc., gathered at
six construction safety design solutions that are being reviewed by OSHA
the OSHA Alliance Program Construction Roundtable meeting at the
to determine if they can be the basis for OSHA compliance assistance
Department of Labor in Washington, D.C. in February 2011. Assistant
products. Since 2004, roundtable participants have developed a variety
Secretary of Labor for Occupational Safety and Health Dr. David Michaels
of free compliance assistance materials for workers and employers.
provided updates on a number of subjects, including OSHA’s 40th anni-
OSHA holds two meetings of the Alliance Program Construction
versary, the Regulatory Agenda and the Fiscal Year 2012 Budget Request.
Roundtable per year to bring together participants with common
To enable them to share information about OSHA activities with
interests. The meetings offer the opportunity for participants to share
their members and downstream customers, the group received OSHA
construction-related information about Alliance activities and successes,
updates on topics including OSHA’s Distracted Driving Initiative, Injury
network with other Alliances, and develop compliance assistance tools
and Illness Prevention Programs, cranes and derricks, silica, confined
and resources.
spaces, residential fall protection and the Severe Violator Enforcement
For more information about the OSHA/CSDA Alliance program, visit
Program. The group also heard overviews of OSHA’s Most Frequently
www.csda.org and click on the “OSHA Alliance” link under “Safety” or
Cited Standards in construction as well as the National Institute for
call 727-577-5004.
w w w. CSD A .ORG
c on c r e t e o p e n i n g s | 4 3
Insurance CornER
Six Secrets to Earn an “A” Grade on Your Workers’ Compensation Insurance Report Card By Curt Dumbleton
W
orkers’ compensation is considered the red-headed stepchild of the insurance industry. It usually
loses money for insurance companies, pays less commission to insurance agents and reminds employers of employee sick time or time off. Therefore, it doesn’t generally get the attention it should. As a company owner or employer, you probably find it difficult to control your most expensive employee benefit, health insurance, which increases 15 to 25 percent every year.
It is advisable to have a Workers’ Com-
However, you can have an immediate and
in the bidding process if their modification
pensation expert at your side. Based on infor-
powerful impact in controlling your second
rate is over 1.00. Each business has a minimum
mation from the Institute of WorkComp
largest employee benefit, which is Workers’
modification factor set by a ratings bureau.
Professionals at www.workcompprofession-
Compensation. Workers’ Compensation is the
Discover yours and reach it. Depending on how
als.com, 75 percent of all audits have errors in
only insurance cost business owners have com-
large your payroll is, the difference between
them. Most of these errors lead to employers
plete control over, yet few take advantage of
what you are paying now and what you would
being overcharged.
be paying at the minimum modification rate
Understand the whole experience
could be anywhere from hundreds to thou-
modification rate process.
sands of dollars. If your modification factor
this situation. As a matter of fact, most business owners are often overcharged for their Workers’ Compensation insurance.
Business owners, not the insurance com-
is not at its minimum, any costs incurred are
pany, pay for employee injuries. When an
affecting your bottom line. When your modi-
employee suffers an injury, your experience
fication factor is at or near the minimum, your
modification factor is affected. Typically, sev-
company is in a much better position.
Understand that Workers’
eral small injuries can cause a more rapid
Compensation is a process with
Develop a return to work program
increase in your modification factor than one
defined steps and dates to follow.
that works both for you and your
large injury. Thus, injuries lead to increases in
employees.
So, what are the six secrets to controlling Workers’ Compensation costs and preventing overcharges?
Workers’ Compensation is a defined pro-
your premium. In addition, multiple injuries
cess. Because you receive an audit after your
Focus on bringing injured workers back to
may lead to lost dividends, premium increases
current year Workers’ Compensation policy
work as quickly as possible. Create a positive
and the cancellation or non-renewal of your
expires, you don’t know your final cost until
work environment in which employees are
policy. Managing a mod rate requires manag-
after the audit. In addition, you have already
valued and their absence is noted. A strong
ing employee health and fitness on the job.
return to work program can be the key to
Know what a minimum modification
achieving your lowest modification factor.
factor is and how to reach it.
When an employee is off the job, a com-
renewed the policy for the following year and the renewal cost may not be accurate. The solution is to prepare for your Workers’ Compensation audit like you would prepare for your income tax audit.
4 4 | JU NE.1 1
Knowing how much money you may be
pany can experience increased costs in over-
losing because you are not at your minimum
time, dips in morale and lower productivity.
modification factor is critical so that you can
A free report entitled Steps to a Solid Return
do something about it. Today, many compa-
to Work Program can be downloaded from
nies who bid jobs cannot even be included
www.widerman.com/csda.
Partner with a medical clinic who knows how Workers’ Compensation works. Seek out medical providers in your area who specialize in treating on-the-job injuries. They
FOr UlTiMATe PrOdUCT PerFOrMANCe Rely on noRton SAwS, BlAdeS & BItS
know how Workers’ Compensation works. Create a relationship with them. Invite them to visit your place of business or job site. Make these medical providers your partners. They can be extremely valuable in helping you manage onthe-job injuries. Communicate to your employees how Workers’ Compensation works and communicate with them when they are injured. Make sure your employees know how Workers’ Compensation works and what they should do if they are injured on the job. As an employer, you need to know immediately when an employee is injured so you or your representative can get the employee the best treatment possible. The goal is to have them miss the least amount of work possible. Workers’ Compensation is the insurance cost over which you have absolute control. Do not be overcharged and do not pay more than you are legally obliged. Be ruthless in working toward
X-Bit drill Bit Series
Vortex Premium Cured Concrete Blade
GMAX early entry Blades
an “A” grade on your experience modification factor scorecard. When you manage the audit process, work hard to achieve your minimum modification factor. Create a clinic relationship, provide Return to Work programs and educate your employees on how Workers’ Compensation works. Maintain a safe workplace and culture of safety through training and building employee morale. By doing
Our expanded offering of saws, diamond blades and core bits provide a single
these things you can drive your costs down. Stop
source for the professional cutting and drilling contractors. Upgraded features help
losing money on your Workers’ Compensation. Do you know the rules of a Workers’ Compensation audit? Company owners or managers can
improve performance while ultimately increasing productivity. For all your job site requirements, choose Norton. The Muscle Behind the Machine.
visit www.widerman.com to download a list of 16 items that do not require a Workers’ Compensation payment. State rules can vary, so it is advised that
Call us at 1 800 854-3281, or visit us online at www.nortonprodiamond.com
you check your individual state requirements for
new PRodUCt
InnoVAtIon
this information. Curt Dumbleton CWCA. is employed by CSDA member Widerman & Co., an independent insurance agency located in Haddonfield, New Jersey. In 2005 he received his Workers’ Compensation Advisor certification from the Institute of WorkComp Professionals. Widerman & Co. joined CSDA in January 2011. For more information, call 800-220-3434 or email cdumbleton@widerman.com.
w w w. CSD A .ORG
Saint-Gobain Abrasives, Inc., 1345 South Acacia Avenue, Fullerton, CA 92831
© Saint-Gobain Abrasives 2011
c on c r e t e o p e n i n g s | 4 5
Industry Bits
James Bond Test™ MK III Developed By James Instruments James Instruments, Inc. has developed the James Bond Test MK III test unit for measuring the bond strength, tensile strength and adhesion strength of concrete, asphalt, tile, concrete repair or other overlay material by the direct tension or pull-off method. The test unit can be used to verify the quality of the material being tested as well as determine the adhesion strength of shotcrete, tile, epoxies, paint and other repair materials, mortars or coatings. The test involves bonding a circular steel disc to the surface of the material being tested by means of an epoxy resin adhesive. A controlled tensile force is then applied to the disc and failure will occur at the weakest point—either in the host material or in the bond between overlay and host material. The new tester features two calibrated gauges that display the maximum load and mechanical damping and has an adjustable alignment plate with built-in leveling facility for both vertical and horizontal pulls. For more information, visit www.ndtjames.com or email info@ndtjames.com.
Diamond Products Introduces Dragon Saw Diamond Products announces the introduction of the 16- and 20-inch blade capacity HDS60 Dragon Saw to its product line. This deep-cutting hydraulic ring saw uses a patent pending, self torque anti-slip drive roller system. The saw has a cutting depth of 16 inches when fitted with a 20-inch blade and is suitable for wet cutting concrete or block. Weighing 29.8 pounds, the Dragon Saw uses hydraulic power of 8 to 9 gallons of fluid per minute. For more information, call Diamond Products at 800-321-5336 or visit www.diamondproducts.com. Pictured from left to right are three generations of the Long family: grandchildren Jessica and Ricky with grandparents, Dorothy and Richard, and father, Rick.
Lombardo Celebrates 50 Years in Business Lombardo Diamond Core Drilling celebrates its 50th year of business in the concrete sawing and drilling industry this year. The company, founded in 1961 by Vincent Lombardo in Santa Clara, California, started with one core drill and a station wagon and has grown to 50 employees and 40 trucks. Over the past 50 years, Lombardo operators have worked with standard tools and techniques such as diamond-tipped chainsaws and flush cutting. A founding member of CSDA, Lombardo proudly supports the association. This family-run business now spans four generations. For more information, call 408-727-7922 or email jhansell@lombardodrilling.com. 4 6 | JU NE.1 1
INDUSTRY
B ITS
Concut, Inc. Announces New Double-Life Wall Saw Blade
Hilti Introduces New Gas Saw Floor Cart The new Hilti DSH-FSC gas saw floor cart is designed for small cutting jobs requiring the flexibility of a hand held gas saw and the precision cut and performance of a larger dedicated floor saw. The cart is compatible with Hilti DSH 700 and DSH 900 gas saws. The gas saw floor cart is made of heavy duty steel construction and is supplied complete with a gravity feed water container that allows the cart to be portable while still providing the dust suppression needed to help contractors meet local ordinances or other requirements. For more information, contact Hilti customer service at 800-879-8000 in the U.S., 800-461-3028 in Canada or visit www.us.hilti.com in the U.S. or www.hilti.ca in Canada.
Concut, Inc. is pleased to introduce the new WS-MAX5 wall saw blade. This unique blade features laser-welded segments that are .800-inch tall—twice the height of conventional blade segments. These tall, sandwich segments are designed to maintain their width and to extend blade life to approximately twice the normal expected life. Since the WS-MAX5 has a wide .225-inch segment (matching the thickness of standard diamond chain), operators can avoid jamming and side clearance problems. The blade is also available in .187-inch and .250-inch versions. For more information, contact Tom Monaghan at 800-243-5888 or email tom@concutusa.com.
New Stihl Cut-Off Saw with Water Control System The new Stihl TS 420 A cut-off saw comes with an electronic water control (EWC) system for wet-cutting. After starting the 4.4-horsepower cut-off machine, the system can be activated with the push of a button. The plus and minus buttons allow the operator to regulate water flow for optimal dust suppression while keeping a hand firmly on the handle of the 22.3-pound saw. The EWC system can use up to 50 percent less water than conventional systems depending on the cutting job and operator technique. A memory function stores the last water setting after the unit is turned off, eliminating the need to readjust the water flow. Water flow stops once the TS 420 A reaches idle speed and begins again when the throttle is engaged. The TS 420 A can cut concrete to depths of 4.9 inches at a speed of 9,000 rpm. For more information, visit www.stihlusa.com or call 757-486-9100.
4 8 | JU NE.1 1
StructureScan Mini 3D Now Available from GSSI Geophysical Survey Systems, Inc. (GSSI) is pleased to announce that its popular StructureScan Mini system for concrete inspection now offers 3D data collection. The new 3D unit was debuted at World of Concrete 2011 and is now available. The StructureScan Mini locates rebar, conduits, post-tension cables and voids in real time. The unit can reach depths of up to 16 inches in concrete and features a laser-positioning system and a 4-wheel drive survey encoder to help mark targets. The unit has also been designed to be water resistant and dust proof (IP-64). The StructureScan Mini system has a center frequency of 1,600 MHz and weighs 3.3 pounds. For more information, call 800-524-3011 or visit www.geophysical.com.
w w w. CSD A .ORG
c on c r e t e o p e n i n g s | 4 9
LET US SET YOU FREE D
C
TOOLGAL USA DIVISION
I
RCE FO
D
C
I
D
C
I
DCI - THE WAY YOU WANT IT Join the continuously growing group of customers who met us at the WORLD of CONCRETE & CON EXPO who have FREED themselves from a Forced Situation by buying and using our SAW SHARK CHAIN AND EQUIPMENT Call us today for your FREE Conversion Kit
REMEMBER, YOU HAVE A CHOICE !
5 0 | JU NE .1 1
877-778-3765
www.dciconcretechain.com
info@dciconcretechain.com
INDUSTRY
B ITS
ICS® Launches Factory Training Program for CWS200 Chain Wall Saw ICS introduces a complimentary factory training program offered with the purchase of a CWS-200 Chain Wall Saw at its Portland, Oregon, location. Customers can send up to two operators to Portland, where ICS will provide lodging, meals, factory training and product education. The training program will educate operators on the best practices, proper care and maintenance and ways to utilize the saw for the best overall return on investment. The training program will start this summer. For more information, call ICS at 800-321-1240 or email marketing@icsbestway.com.
New and Improved Website from Husqvarna Husqvarna Construction Products has already launched a new, enhanced website at www.husqvarnacp.com. The updated site has been designed to be easier to navigate and enables contractors to find the right information, from technical specs and ‘how to’ guides to learning about products and accessories. It features an interactive tool guide to help contractors find the appropriate diamond tool for the material being cut plus upgrades to equipment pages that include technical specifications, tool recommendations and accessories. The website also features frequently asked questions as well as maintenance guides and videos. For more information, contact Cate Stratemeier at 913-928-1442 or visit www.husqvarnacp.com.
New Appointments for Diamond Tools Technology Diamond Tools Technology (DTT) is pleased to announce that Mark Turner has been appointed National Sales Manager, responsible for managing and directing DTT’s sales team. Turner has previously worked for Norton and has contracting experience with Penhall Company. Jim Fleming will cover the East Coast sales territory for DTT, from Washington, D.C. to Boston. Fleming has over 20 years of sales experience in construction products and industrial tools. Myles McDougal will cover the Texas and Louisiana sales territory. He comes to DTT with 20 years of experience in the concrete cutting industry, starting as an operator and then progressing to lead operator, then to sales and dispatch. For more information, contact Mark Turner at mark@diamondtoolstechnology.com.
Turner
w w w. CSD A .ORG
Fleming
McDougal
DITEQ introduces new Hand Saw Blade DITEQ Corporation has added a new blade to its line of ARIX hand saw blades. The new blade, the C51-AX10, has been designed to cut concrete with heavy steel rebar. ARIX technology is designed so that each individual diamond is strategically placed throughout the segment. This new blade has increased cutting speed and life span than its predecessors. For more information, call 866-688-1032 or visit www.diteq.com.
c on c re t e o p e n i n g s | 5 1
INDUSTRY
B ITS
Hilti Appoints Key Project Manager Hilti, Inc. is pleased to announce Rick Glidewell has joined the company as key project manager. Glidewell has 10 years experience in the industry and will be supporting Hilti’s professional cutting customers in the use of Hilti wall saws, wire saws and coring equipment. Glidewell previously worked at Husqvarna where he held several positions responsible for wall and wire sawing demonstrations, start up of wall and wire sawing equipment, service on equipment Glidewell and wire sawing training for operators. He is available to provide assistance and knowledge of products, applications and service. For more information, call Hilti customer service atNDT_ConcOpenings:Layout 800-879-4000. 1 1/12/11
Expert Equipment Adds T10-700-EL Core Drill Rig to Lineup Expert Equipment Company announces the addition of the Cardi T10-700-EL core drill rig to its lineup. The rig uses familiar components to the Cardi range. The T10-700-EL has been designed to create holes up to 28 inches in diameter using a standard 30-amp, 120-volt motor. The idle rpm’s are 150, 320 and 530, and load rpm’s at 30 amps are 85, 180 and 300. Expert Equipment also offers this drill with a new style of heavy duty spacer that mounts on the Cardi six-hole roller carriage. This setup offers 8- and 12-inch spacers with an optional quick connect motor mount. For more information, call 713-797-9886 or visit www. expertequipment.com.
9:40 AM
Page 1
The James R-Meter MK III & Mini R-Meter STRENGTH ULTRASONICS
R-Meter MK III Most Advanced Rebar Locator
CORROSION
Mini R-Meter An Economical Rebar Locator for Professionals
www.NDTjames.eu • email:europe@NDTjames.eu
3727 N. Kedzie Ave., Chicago, IL 60618
Windmolen 22, 7609 NN Almelo, The Netherlands
+31 (0)548 659032
Test Well. Build Well.
5 2 | JU NE.1 1
MOISTURE
www.NDTjames.com • email:info@NDTjames.com
800-426-6500 • 773-463-6565
LOCATORS
Ren t Un al Ava its ilab le
New pH Control System Available from Slurry Solutions Slurry Solutions, a division of Gölz, is now a distributor for the new Poli-Cut pH control system from Fortrans, Inc. The unit is a self-contained portable pH control system for the concrete polishing, grinding and cutting industries. The system uses carbon dioxide gas that is diffused and injected into the waste water to automatically lower the pH to 7.0, which is neutral and safe to discharge. The Poli-Cut system comes complete with an integral 200-gallon tank, pump, a programmable logic controller and Fortran’s proprietary carbon dioxide diffusion-injection unit. The system is mounted on 5-inch polyurethane swivel casters for loading and maneuvering at the jobsite. The two-speed pump will treat 1,500 to 3,000 gallons per hour. Also included is a 2-inch bottom drain on the tank with a 50-foot roll of flat hose with cam lock fittings for discharge. The unit requires a 115-volt cord connection and a supply of carbon dioxide with a regulator to connect to the system. For more information, contact Mark Critchfield at 573-219-7330 or email mark.critchfield@gmail.com.
PRO TOOLS : unbeatable technology The Worl d ’s M o s T A dvAnc e d PATT e r ne d di A M ond Te c h no logy
proFessional saW Blades Bridge deck, wall saw, road & slab sawing
ring saW Blades 10 mm segment height, .235” thickness available for following with a chain saw, includes drive wheel
core Bits 8mm segment height, 14” tube length, sizes up to 10” diameter
Technology: A new generation of diamond Tools Strategic (patterned) diamond placement allows for maximized cutting efficiency. Every diamond is placed exactly where optimum performance can be achieved. This specific placement ensures that the full potential of every diamond is reached. By optimizing each diamond’s usefulness, Zenesis truly is the leader in diamond tool performance.
Fastest cutting • Operator’s experience cutting speeds faster than other traditional tools on the market* longer liFe • Significantly improves both cutting speed and tool life – up to 20% more than products in same category. • No diamond pulls out of the segment until it is completely used, extending the life of the tool.
Patented patterned placement
consistent perFormance • Patterned technology offers the most consistent results for every cut.
Random diamond placement *Comparison to tools in same category.
11913 Cartwright Rd. • Grandview, MO 64030 Office: 816-268-8310 • Toll Free: 866-322-4078
Fax: 816-268-8314 • www.diamondvantage.com
w w w. CSD A .ORG
c on c r e t e o p e n i n g s | 5 3
INDUSTRY
B ITS
Australian Association Appoints New President Rob East of Qld Concrete Drilling and Sawing in Archerfield, Queensland, has been appointed the new president of the Concrete Sawing & Drilling Association Australia (CSDAA). The announcement was made at the association’s annual general meeting and conference on March 3 and 4 in Penrith, New South Wales. East will serve a two-year term as president. He has been a member of CSDAA for 16 years, and will continue the association’s goal of providing benefits and support to its members, including training, accreditation and professional advice, as well as encouraging the use of trained and accredited concrete cutting contractors to government departments and demolition and construction companies. For more information, contact CSDAA at 61-03 9867 0227 or email info@csdaa.com.au.
5 4 | JU NE.1 1
A1 Kiwi Cutter & Drillers Purchases First Hilti Wall Saw in New Zealand Hilti have confirmed that CSDA contractor member A1 Kiwi Cutter & Drillers Ltd. of Auckland recently became owners of the first DS TS20-E wall saw to be sold in New Zealand. The DS TS20-E is designed to cut to depths of up to 21 inches and the system is equipped with a 15-kilowatt electric motor that has a 32-amp supply. The wall saw operates at variable speeds and can accommodate blades from 24 to 48 inches in diameter. A1 Kiwi Cutter & Drillers have already used the DS TS20-E on several projects, including the cutting and removal of a concrete swimming pool at the SkyCity Hotel in Auckland. For more information about A1 Kiwi Cutters & Drillers Ltd., contact Penny Simons at 64-9 420 3386 or email thegirls@kiwicutters.co.nz.
INDUSTRY
B ITS
Bosch Introduces GLL2-40 Cross-Line Laser
Seal/No Seal Group Supports Research Efforts The Seal/No Seal Group represents the pavement industry, and its members are committed to quantifying the long-term effectiveness of joint sealants in concrete pavement. The group has developed a committed and active member base, willing to work together to advance the industry, and engaged with key industry associations including the Concrete Sawing & Drilling Association. The group has established a website that is used to communicate industry news, committee research findings and other information in support of the industry. Other accomplishments for the group include having four state DOTs conduct evaluations of their existing seal/no seal test sections, partnering with roadway owners to construct 10 new sealant test sections and hiring the Texas Transportation Institute to conduct research on the effects of joint sealant condition on moisture infiltration and erosion potential. The group also worked with Purdue University to support research efforts to search for the cause for premature joint deterioration. For more information about the Seal/No Seal Group, call Scott Eilken at 708-728-1895, email info@sealnoseal.org or visit www.sealnoseal.org.
Up To 16” Cutting Depth
Uses a 16” or 20” Ring Blade
The Bosch GLL2-40 is a cross-line laser designed for all professional interior jobsites up to 30-feet. The compact unit projects lines independently or together for various types of building construction leveling and alignment applications with 0.125-inch accuracy. Weighing eight-ounces, the GLL2-40 is less than two inches wide and less than four inches in length and height. The unit can be used to evenly mark cutting lines or set accurate core drilling points. A single button control allows the selection of horizontal, vertical, cross line or manual modes of operation. A leveling system locks the pendulum when the GLL2-40 is switched off, allowing all parts of the unit to be protected during transport. An over-mold construction coupled with a recessed window ensure against damage from water and dust. The unit also includes a detachable floor and magnetic mount that allows full rotation. The mount is equipped with a 0.25-20-inch or 0.625-11-inch tripod mounting thread for additional mounting options. For more information, visit www.boschtools.com or call 877-267-2499.
« The only hand saw capable of cutting 16” deep in concrete or block
« Requires LOW maintenance while offering superb performance
« Cuts straight, eliminates corner drilling, prevents «
over-cuts and allows more of the blade to be used pre-cut recommended Light weight - only 29.8 lbs.
WET CUTTING ONLY
w w w. CSD A .ORG
HDS60 CUTTING DEPTH Blade Diameter
Cutting Depth
Maximum Depth with No Overcut
16”
12”
8”
20”
16”
12”
c on c r e t e o p e n i n g s | 5 5
CSDA MEMBERSHIP APPLICATION
PRINCIPAL BUSINESS ACTIVITY
$525
$1,090
$810
$855
$1,375
$1,030
$1,285
$2,040
$1,525
$1,730
$3,295
$2,175
$4,420
$2,750
$5,495
$355
$630
$2,465
*AFFILIATE: A person, firm, corporation, society, government agency or other organization providing services to the concrete sawing and drilling industry.
$130
C S D A • 1 3 5 7 7 F e at h e r S o u n d D r i v e , S u i t e 5 6 0 , C l e a r w at e r , F l 3 3 7 6 2 t e l : 7 2 7 . 5 7 7 . 5 0 0 4 fa x : 7 2 7 . 5 7 7 . 5 0 1 2 w w w . cs d a . o r g 5 6 | JU NE.1 1
18reasons
t o b e c o m e a CS D A M e mb e r
Networking at the Annual Convention and Seasonal Meetings
Specifications, Standards, Tolerances and Best Practices
The number one benefit for members has always been the opportunity to network with cutting professionals at the annual convention and seasonal meetings. This networking provides opportunities to forge new relationships and learn from other experienced professionals.
Specifications, Standards, Tolerances and Best Practices are available for all types of cutting disciplines. Twenty-four documents have been developed and new ones are always in production.
CSDA Training
Members can market their company with How to Market Your Concrete Cutting Business and make presentations with the Diamond Advantage Seminar Planning & Presentation Manual. Four-color brochures and flyers are available for members to promote their business to customers and are easily personalized so members can avoid the cost of developing their own.
Over 2,000 members have graduated from more than 20 classroom, hands-on and online training programs: Cutting Edge, Slab Sawing & Drilling, Wall Sawing, Wire Sawing, Operator Certification, OSHA Construction Safety and Estimating. CSDA offers online training at www. csdatraining.com for those not able to afford the time or the money to send operators to remote classes. Owners/managers can monitor testing, scoring and documentation. Concrete Openings Magazine
Concrete Openings (www.concreteopenings.com) is the only professional magazine dedicated to concrete cutting with a circulation of 16,000 per issue. Members can advertise at significant discounts and the opportunity to have their job stories reach over 7,000 architects, engineers, general contractors and government officials. CSDA Insurance Program
The CSDA Insurance Program offers members coverage that includes Workers’ Compensation, auto, comprehensive general liability, environmental pollution, professional liability, equipment, Employment Practices Liability (EPL) and other lines specifically geared for the concrete cutting industry. CSDA Website
The CSDA Website at www.csda.org contains a wealth of information available 24/7 in the “Members” section. The online discussion boards provide members a forum to discuss technical issues, sell equipment, hire employees or any other relevant topics. CSDA Safety Resources and Toolbox Safety Tips (TSTs)
The 230-page CSDA Safety Manual, CSDA 57-page Safety Handbook and five safety DVDs are designed specifically for concrete cutters and are available to members at a significant discount. TSTs can be used in employee safety meetings and can be an important part of your company’s safety program. New TSTs are released every quarter. Roundtables
The roundtable sessions at the annual convention and other meetings give members a chance to share their wisdom and acquire additional knowledge. Information gained during the roundtables gives members new ideas to implement within their companies and can save them money. FREE World of Concrete Registration
Members receive free registration and reduced seminar fees for the industry’s annual exhibition of concrete-related equipment and supplies. Mentor Program
New members can receive personalized assistance from a current CSDA Board or committee member during their first year of membership.
w w w. CSD A .ORG
Manuals and Promotional Literature
Specifier Resource Guide and Membership Directory
The CSDA Membership Directory is available in print form and on the Website. The searchable web directory is especially valuable as the CSDA Website averages 150,000 page views per month. The Specifications, Standards, Tolerances and Best Practice documents are included in the print version of the resource guide and are also available online. Membership Profile Analysis
A periodic survey of members to collect statistical information on operating and financial information such as wages, profit and loss, safety, equipment and diamond tool costs. Slurry Analysis Report
This is an Association-sponsored, 60-page report for members. The slurry analysis was performed by an environmental engineering firm with data compared to federal standards and contains recommended guidelines for slurry management. Representation with Governmental Organizations
CSDA has formed an Alliance with OSHA to advance the safety of cutting contractors. This partnership includes issuing Best Practice and Toolbox Safety Talk documents, joint exhibitions at trade shows, review of safety materials and roundtables. CSDA also actively participates with NIOSH on field testing. Discount Programs
CSDA offers its members exclusive programs for insurance and online training, plus discounts on freight services, credit collection services, drug testing and safety services. Cooperation with Industry Associations
CSDA is a founding member of the International Association of Concrete Drillers and Sawers (IACDS) and works with other associations around the globe to promote concrete cutting and the sustainability of concrete as a building material. CSDA Next Generation Group
The CSDA Next Generation group is made up of members and nonmembers age 45 and under. The purpose of the group is to continue to grow the association while serving the needs and wants of the younger generation with the goal of continuing the excellence of the Concrete Sawing & Drilling Association. The group meets during the seasonal meetings, at the annual convention and at the World of Concrete.
c on c r e t e o p e n i n g s | 5 7
Certified Operator Companies Companies listed here have invested time and money to send their operators to CSDA’s Operator Certification. If you are committed to professionalism in the concrete cutting industry, consider sending your operators through the training programs offered by the Concrete Sawing & Drilling Association.
A.E. BRICE & ASSOCIATES, INC.
CAL WEST CONCRETE CUTTING, INC.
core solutions ltd.
DEANDREA CORING & SAWING, INC.
1510 Aspen St Baltimore, MD 21226 Tel: 410-354-8890 Fax: 410-354-8894 www.sawconcrete.com
1153 Vanderbilt Cir Manteca, CA 95337 Tel: 209-823-2236 Fax: 209-823-0740 www.calwestconcretecutting.com
PO Box 3349 Maraval TRINIDAD & TOBAGO Tel: 868-622-8334 Fax: 868-622-3074 www.coresolutionsltd.com
9630 Dallas St Henderson, CO 80640 Tel: 303-422-3885 Fax: 303-431-9661 www.deandreacoring.com
ABC CUTTING CONTRACTORS– BIRMINGHAM
CAL WEST CONCRETE CUTTING, INC.
3060 Dublin Cir Bessemer, AL 35022 Tel: 205-425-7711 Fax: 205-425-7769 www.abccuttingala.com
3000 Tara Ct Union City, CA 94587 Tel: 510-656-0253 Fax: 510-656-8563 www.calwestconcretecutting.com
CORING & CUTTING SERVICES, INC.
DELTA CONTRACTORS & ASSOCIATES, LLC
1107 N Redmond Rd Jacksonville, AR 72076 Tel: 501-779-4072 Fax: 501-985-9781 www.sawconcrete.com
605 S Caton Ave Baltimore, MD 21229 Tel: 410-624-0990 Fax: 410-624-0991 www.deltacontractorsllc.com
CORING & CUTTING SERVICES, INC.
DERRICK CONCRETE CUTTING & CONSTRUCTION LTD.
CENTRAL CONCRETE CUTTING, INC. ABC CUTTING CONTRACTORS–MOBILE
26181 Equity Dr Daphne, AL 36526 Tel: 251-625-1100 Fax: 251-625-1103 www.abccuttingala.com
W719 Leroy St Edgar, WI 54426 Tel: 715-352-2552 Fax: 715-352-2625 www.centralconcretecutting.com
2711 SE Otis Corley Dr Bentonville, AR 72712 Tel: 479-271-9672 Fax: 479-271-9674 www.sawconcrete.com
con-cor company, inc. ADVANCED CORING & CUTTING CORP.
1766 Route 34 Farmingdale, NJ 07727 Tel: 732-681-7733 Fax: 732-681-8733 www.advancedcoringandcutting.com
W146N5790 Enterprise Ave Menomonee Falls, WI 53051 Tel: 262-781-3660 Fax: 262-252-3832 www.con-cor_co.com concrete cutting & breaking co.
AMBERCROFT LABOURERS’ 506 TRAINING CENTRE
1600 Major Mackenzie Dr E Richmond Hill, ON L4S 1P4 CANADA Tel: 905-883-4268 Fax: 905-883-4894 www.506tc.org ATLANTIC CONCRETE CUTTING, INC.
PO Box 98 Mt. Holly, NJ 08060 Tel: 609-261-7200 Fax: 609-261-7246 www.atlanticconcretecutting.com B.T. RENTALS LIMITED
#13 Buller St Woodbrook TRINIDAD & TOBAGO Tel: 868-628-2703 Fax: 868-622-4244
5 8 | JU NE.1 1
11226 Phillips Pkwy Dr E #2 Jacksonville, FL 32256 Tel: 904-262-9985 Fax: 904-262-1477 www.concut.com CONCRETE CUTTING SPECIALISTS, INC.
10333 Hercules Rd Freeland, MI 48623 Tel: 989-695-5344 Fax: 989-695-5345 CONCRETE PENETRATING CO.
2303 Shorecrest Dr Dallas, TX 75235 Tel: 214-634-2990 Fax: 214-634-0953 www.concretepenetrating.com CONCRETE RENOVATION, INC.
6600 Randolph Blvd San Antonio, TX 78233 Tel: 210-653-6120 Fax: 210-590-2316 www.concreterenovation.com
CORING & CUTTING of springfield, inc.
7039 Gateway Blvd NW Edmonton, AB T6H 2J1 CANADA Tel: 780-436-7934 Fax: 780-435-4389 www.derrickconcrete.com
2074 N James River Ct Nixa, MO 65714 Tel: 417-725-4534 Fax: 417-725-0073 www.sawconcrete.com
DIXIE CONCRETE CUTTING CO.
CUT-RITE CONCRETE CUTTING CORP.
DIXIE CONCRETE CUTTING, INC.
22 Lockbridge St Pawtucket, RI 02860 Tel: 401-728-8200 Fax: 401-727-2953 www.cutriteccc.com CUTTING EDGE SERVICES CORP.
5297 Port Blvd S College Park, GA 30349 Tel: 404-761-1100 Fax: 404-669-2550
16 Maple Creek Cir Greenville, SC 29607 Tel: 864-299-6600 Fax: 864-299-5009 EAST COAST CONCRETE CUTTING CO., INC.
1535 Old S.R. 74 Batavia, OH 45103 Tel: 513-388-0199 Fax: 513-732-1248 www.cuttingedgeservices.com
7229 Montevideo Rd Jessup, MD 20794 Tel: 410-799-4540 Fax: 410-799-1978 www.eastcoastconcretecutting.com
dari concrete sawing & drilling
EASTERN CONCRETE CUTTING CORP.
421 Raleigh View Rd Raleigh, NC 27610 Tel: 919-278-8145 Fax: 919-772-4311 www.dhgriffin.com
37-31 29th St Long Island City, NY 11101 Tel: 718-361-6123 Fax: 718-361-6101 www.easterncutting.com
GRONEMEIER CONCRETE CUTTING, INC.
22 White Pl Bloomington, IL 61701 Tel: 309-829-7991 Fax: 309-829-2685 www.gronemeier.com
HOLES INCORPORATED
9911 Franklin Rd Houston, TX 77070 Tel: 281-469-7070 Fax: 281-469-6207 www.holesinc.com HOLES OF SAN ANTONIO, INC.
HAFNER AND SON, INC.
90 Atlas Rd Northampton, PA 18067 Tel: 1-800-ANCHORS Fax: 610-262-4809 www.hafnerandson.com HARD ROCK CONCRETE CUTTERS, INC.
601 Chaddick Dr Wheeling, IL 60090 Tel: 847-699-0010 Fax: 847-699-0292 www.hardrockconcretecutters. com HARD ROCK SAWING AND DRILLING SPECIALIST CO.
PO Box 718 Keshena, WI 54135 Tel: 715-799-3823 Fax: 715-831-7840 www.hardrocksawanddrill.com
118 Braniff Dr San Antonio, TX 78216 Tel: 210-349-5256 Fax: 210-349-0727 www.holesofsa.com INTERNATIONAL DRILLING & SAWING, INC.
PO Box 250013 Montgomery, AL 36125 Tel: 334-288-2355 Fax: 334-288-7299 www.idscuts.com K.C. CORING & CUTTING CONSTRUCTION, INC.
7240 Central St Kansas City, MO 64114 Tel: 816-523-2015 Fax: 816-523-8493 www.sawconcrete.com
M6 CONCRETE CUTTING & CORING
1030 S McComas St Wichita, KS 67213 Tel: 316-263-7251 Fax: 316-264-3517 www.conacc.com OKLAHOMA CORING & CUTTING, INC.
PROFESSIONAL CONCRETE SAWING
8539 Oliver Rd Erie, PA 16509 Tel: 814-566-5555 Fax: 814-866-5555 ROUGHNECK CONCRETE DRILLING & SAWING
6025 N Douglas Blvd Arcadia, OK 73007 Tel: 405-715-2500 Fax: 405-715-2504 www.sawconcrete.com
8400 Lehigh Ave Morton Grove, IL 60053 Tel: 847-966-6666 Fax: 847-966-6577 www.roughneck1.com
PACIFIC CONCRETE CUTTING & CORING, INC.
TRUE-LINE CORING & CUTTING– chattanooga LLC
PO Box 662261 Lihue, HI 96766 Tel: 808-245-7171 Fax: 808-245-9393 www.pccchawaii.com
1903 S Highland Park Ave Chattanooga, TN 37404 Tel: 423-624-7369 Fax: 423-624-7977 www.sawconcrete.com
PENHALL COMPANY/CONCRETE CORING COMPANY OF HAWAII
TRUE-LINE CORING & CUTTING– KNOXVILLE LLC
99-1026 Iwaena St Aiea, HI 96701 Tel: 808-488-8222 Fax: 808-487-6679 www.penhall.com
1902 Middlebrook Pike Knoxville, TN 37921 Tel: 865-637-2131 Fax: 865-637-1973 www.sawconcrete.com TRUE-LINE CORING & CUTTING– NASHVILLE LLC
LOMBARDO DIAMOND CORE DRILLING CO., INC.
280 Hermitage Ave Nashville, TN 37210 Tel: 615-255-2673 Fax: 615-255-9685 www.sawconcrete.com
2225 De La Cruz Blvd Santa Clara, CA 95050 Tel: 408-727-7922 Fax: 408-988-5326 www.lombardodrilling.com
CSDA is Turning 40
The CSDA Next Generation group and other volunteers are
events, especially the past 15 years (1996 to 2011), since the 25th
working on the CSDA 40th anniversary commemorative book, and
anniversary booklet was produced, are encouraged to contact Erin
will be conducting interviews for source material. Any members
O’Brien at 727-577-5004 or email erin@csda.org. The deadline for
with photographs or written materials of CSDA members or
materials is November 1, 2011.
w w w. CSD A .ORG
c on c r e t e o p e n i n g s | 5 9
Calendar 2011 CSDA Summer Meetings
June 9-10, 2011 Hyatt Regency Tulsa Tulsa, OK Tel: 727-577-5004 www.csda.org Email: info@csda.org International Concrete Sustainability Conference
August 9-11, 2011 Boston, MA Tel: 847-918-7218 Email: llemay@nrmca.org
CSDA Fall Meetings August 18-19, 2011 • VANCOUVER, BC
Our World in Concrete & Structures Conference
August 14-16, 2011 Goodward Park Hotel Singapore Tel: 65-6733 2922 www.cipremier.com CSDA Fall Meetings
August 18-19, 2011 Hyatt Regency Vancouver Vancouver, BC, Canada Tel: 727-577-5004 www.csda.org Email: info@csda.org Concrete Show South America 2011
August 31-September 2, 2011 Centro de Exposicoes Imigrantes Sao Paulo, Brazil Tel: 55-11-4689-1935 Email: concrete@concreteshow.com.br
CSDA Wire Sawing 201 Operator Certification November 18-19, 2011 CSDA Wire Sawing 201 Operator Certification
November 18-19, 2011 St. Petersburg College Clearwater, FL Tel: 727-577-5004 www.csda.org Email: info@csda.org
November 14-15, 2011 St. Petersburg College Clearwater, FL Tel: 727-577-5004 www.csda.org Email: info@csda.org
December 1-2, 2011 Canyons Resort Park City, UT Tel: 727-577-5004 www.csda.org Email: info@csda.org
March 5-6, 2012 Sheraton Maui Ka’anapali Beach, HI Tel: 727-577-5004 www.csda.org Email: info@csda.org CSDA 2012 Convention
2012
CSDA Estimating Class
November 15-16, 2011 St. Petersburg College Clearwater, FL Tel: 727-577-5004 www.csda.org Email: info@csda.org
World of Concrete
CSDA Wall Sawing 201 Operator Certification
CSDA Board Meeting
November 16-17, 2011 St. Petersburg College Clearwater, FL Tel: 727-577-5004 www.csda.org Email: info@csda.org
January 25, 2012 Las Vegas Convention Center Las Vegas, NV Tel: 727-577-5004 www.csda.org Email: info@csda.org
6 0 | JU NE.1 1
March 5, 2012 Sheraton Maui Ka’anapali Beach, HI Tel: 727-577-5004 www.csda.org Email: info@csda.org CSDA Spring Meetings
CSDA Winter Meetings CSDA Slab Sawing and Drilling 201 Operator Certification
IACDS ANNUAL Meeting
January 23-27, 2012 Las Vegas Convention Center Las Vegas, NV Tel: 972-536-6379 www.worldofconcrete.com
March 7-9, 2012 Sheraton Maui Ka’anapali Beach, HI Tel: 727-577-5004 www.csda.org Email: info@csda.org National Demolition Association 2012 Convention
March 11-14, 2012 The Henry B. Gonzalez Convention Center & Grand Hyatt Hotel San Antonio, TX Tel: 800-541-2412 www.demolitionassociation.com
New Members The Concrete Sawing & Drilling Association is a nonprofit trade association of contractors, manufacturers, distributors and affiliates from the construction and renovation industry. Membership in CSDA is open to concrete cutting contractors, manufacturers and distributors
North American Contractor Concrete Cutting Systems, Inc.
David Nevrotski 2512 Orthodox St Philadelphia, PA 19137 Tel: 215-533-0652 Fax: 215-533-5870 Email: sawcutr@verizon.net www.concretecuttingsystems.net Cutcrete Sawing
David Greding 207 W Los Angeles Ave # 174 Moorpark, CA 93021 Tel: 805-432-5860 Fax: 805-334-6361 Email: cutcrete@gmail.com
Rick’s Concrete Sawing, Inc.
Cyclone Diamond Products Ltd.
James Mann PO Box 5634 Topeka, KS 66605 Tel: 785-862-5400 Fax: 785-862-0478 Email: lmann555@aol.com
Diane Webb 107-2845 23 St NE Calgary, AB T2E 7A4 CANADA Tel: 403-250-5568 Fax: 403-250-5586 Email: diane@cyclonediamond.com www.cyclonediamond.com
Shelby Concrete Sawing
Jeffrey Pitman 8829 Eatonwick Dr Memphis, TN 38018 Tel: 901-266-3303 Email: knowing_heis4me@bellsouth.net Urban Sawing & Scanning Co. Ltd.
Family Room Productions, Inc.
Roland Majeau 4912 142 St NW Edmonton, AB T6H 4B1 CANADA Tel: 780-983-1799 Email: roland@rolandmajeau.com McCrary Construction Services
Lu McCrary PO Box 2402 Columbus, MS 39704 Tel: 662-244-3424 Fax: 662-327-1970 Email: lu.mccrary@mccrarywest.com www.mccraryconstructionservices.com
of concrete cutting equipment and affiliated companies who provide products and services to the concrete sawing and drilling industry. Founded in 1972, CSDA reached the milestone of 500 member companies in 2006.
Steven Velecky 266 1st St E North Vancouver, BC V7L 1B3 CANADA Tel: 604-987-2712 Fax: 604-987-2702 Email: urbansaw@shawcable.com
Manufacturer Archer USA / Dexpan USA
Richard Azevedo 1665 Futurity Dr Sunland Park, NM 88063 Tel: 575-874-9188 Fax: 575-874-9108 Email: sales@archerusa.com www.dexpan.com
Distributor Glacier Diamond, Inc.
Jeff Hayden 4410 E La Palma Ave Anaheim, CA 92807 Tel: 714-854-9600 Fax: 714-854-9700 Email: glacierana@gmail.com
Affiliate Widerman & Company
Curt Dumbleton 70 Tanner St Haddonfield, NJ 08033 Tel: 856-428-0939 Fax: 856-429-7439 Email: cdumbleton@widerman.com www.widerman.com
Find a Member Online The CSDA Website includes a “Find a Member” search tool on its home page, where specifiers of concrete cutting can locate a professional CSDA contractor serving their area through an interactive map. Simply click on an individual state or area to get a list of members from that state, or use the dropdown boxes to enter more specific search criteria. Visit www.csda.org and click on the map icon to get started.
Why I Joined CSDA Concrete Renovation, Inc. began in 1990 as two trucks and two guys—me
Personally, the best benefit of being a member is attending the quarterly
being one of the guys—operating out of San Antonio, Texas. I knew that
meetings. I have served on the CSDA Board of Directors and my wife,
in order for the business to be truly successful, I was going to have to find
Donna, is a current Board member.We are both actively involved in the
help and learn as much as I could. The first place I thought of was the
association and have been part of several committees. It is with pride that we
Concrete Sawing and Drilling Association. After doing some research on
can say we have helped improve the safety of contractors in our industry by
what CSDA offered in the way of training programs, safety materials
being part of CSDA’s safety and training committees. I cannot stress enough
and equipment specifications, I knew this was
how much knowledge can be gained by simply talking with peers. There is a
the right association for the company. Since
vast amount of knowledge out there, and all you have to do is ask questions.
joining the association in 1991, I and several of my operators have gone through CSDA’s training and certification classes. Every one of my operators came back to work more knowledgeable about what material they were cutting and the equipment they were using. This really raised the Patrick Harris
w w w. CSD A .ORG
company’s reputation.
Being a member of CSDA continues to be an important part of our business, and because the association is always looking to prepare contractors for the future, I feel it always will be. Patrick Harris Concrete Renovation, Inc. San Antonio, Texas ptharris@sbcglobal.net
c on c r e t e o p e n i n g s | 6 1
t h e o f f i c i a l m a g a z i n e o f t h e c o n c r e t e s a w i n g & d r i l l i n g a s s o c i at i o n
Want to Target the Specialized Industry of Sawing & Drilling? Advertising in Concrete Openings magazine is the only way to reach the specialty market of sawing and drilling contractors who cut concrete, asphalt or masonry because it is the only magazine in the market specifically targeted to this segment of the sawing and drilling industry.
How Do You Reach 16,000+ Sawing and Drilling Professionals? Each issue of Concrete Openings magazine is sent to more than 9,500 sawing and drilling operators, manufacturers of sawing and drilling equipment and suppliers to the industry and more than 6,500 specifiers of concrete cutting services around the world.
Who Reads the Magazine? Concrete Openings reaches sawing and drilling contractors, as well as specifiers of sawing and drilling services including engineers, architects, general contractors and governmental agencies. Why waste your message on unnecessary circulation? Advertising in Concrete Openings guarantees a targeted audience of industry professionals.
Readership by Profession
Circulation 16,000+ minimum, per issue 9,500+
52%
member and prospective member companies made up of sawing and drilling contractors,manufacturers, distributors and affiliates
6,500+ general contractors, engineers, architects and government officials who specify sawing and drilling
Concrete Openings Website Concrete Openings has its own website. Advertisers have direct links to their websites placed on our Advertisers page as a complimentary addition to ad placement. A full copy of the magazine is also available for visitors to read on the website. Visitors to the site can now access our advertisers at the touch of a button. The Concrete Openings Website also has advertising opportunities available throughout the year. Visit www.concreteopenings.com for more information.
Readership Per Issue In a recent poll, a section of Concrete Openings subscribers revealed that 66% pass on their copy of the magazine to at least one other person, with almost 25% stating that the magazine is passed on to four or more people each issue. This translates to an average of 3.75 people reading each issue of the magazine for a total readership per year of approximately 60,000.
8% 40%
• Specifiers • Cutting Contractors • Manufacturers, Distributors Readership by Location
85%
5% 4% 6%
• United States • Asia, Africa, Australia • Europe • Canada, South America
To receive additional information about products advertised in this issue, visit the advertisers page on concreteopenings.com, or contact the vendors below. PAGE ADVERTISER PHONE EMAIL 6 Brokk, Inc. 49 Company Wrench 39 Diamond Pauber srl 54, 55, Inside Front Cover Diamond Products 41 Diamond Tools Technology 53 Diamond Vantage, Inc. 61 DITEQ Corporation 29 EDCO-Equipment Development Co., Inc. 25 Expert Equipment Company 19 Geophysical Survey Systems, Inc. (GSSI) 47 Glacier Diamond, Inc. 41 Grabber Power Products Inside Back Cover Hilti North America 32, 33, Outside Back Cover Husqvarna Construction Products 2 ICS, Blount Inc. 52 James Instruments, Inc. 45 Norton Pro Diamond 17 Pentruder, Inc. 23 Reimann & Georger Corporation 49 Rhino Tools S.L. 27 Sensors & Software 50 Toolgal USA Corp/DCI 5 Western Saw
6 2 | JU NE.1 1
800-621-7856 740-654-5304 39-05 85 830425 800-321-5336 612-408-9253 816-268-8310 816-246-5515 301-663-1600 713-797-9886 603-893-1109 714-854-9600 480-967-2545 918-872-3553 913-928-1442 503-653-4644 773-463-6565 800-854-3281 562-445-6429 716-895-1156 34-986 369 310 905-624-8909 706-283-9556 805-981-0999
henrik@brokkinc.com katie@companywrench.com info@diamondpauber.it jpalmer@diamondproducts.com roger@diamondtoolstechnology.com info@diamondvantage.com jmiller@diteq.com moran@edcoinc.com expertequipment@sbcglobal.net harmonj@geophysical.com glacierana@att.net jorge@grabberpower.com bennett.myers@hilti.com cate.stratemeier@husqvarna.com joet@icsbestway.com angie@ndtjames.com stephen.m.anderson@saint-gobain.com terry@pentruderinc.com peter.kowalczyk@rgcproducts.com stuart@rhinotools.es sales@sensoft.ca admin@toolgalusa.com cole@westernsaw.com
For CSDA Members only ...
As a valued member of CSDA, you're invited to take advantage of these never before seen low prices!
Pricing Effective June 1 - July 15, 2011
Pricing in U.S. dollars
866-688-1032 DIAMOND TOOLS & EQUIPMENT
ShiBuYa Y Core DrillS - The Choi Ya hoiCe of profeSSioNalS New Two Year warra arraNTY NTY!
TS-252 Core Drill 20 ampS - 2 SpeeD
The preferreD Core Drill BY pro’S for everYDaY DrilliNG eSpeCiallY oN wallS
$
1,780
Does not include bit
New Two Year warra arraNTY NTY!
piSTol Grip rip haND Core Drill verSaTile aaND reliaB reliaBle
RPM (Under Load) 560/1400/2900 Bit Capacity (Max. Handheld) 4” Bit Capacity (Max. Fix Mounted) 6.5” Weight 15 lb.
List $2,545 Part DR0008
Sale Net
Motor Base Style RPM (no Load) Bit Capacity Column Length Weight:
rh1532 1532 Core Drill 15 ampSS - 3 SpeeD
New
1,395
DIAMOND TOOLS & EQUIPMENT Two Year
$
R1721 Fixed 450/900 12" Max. 39.4" 43 lb.
warraNTY!
Sale Net Pkg Price List $1,995 Part DR2023
TS-353 Core Drill 23 ampS - 3 SpeeD
bit sold separately
TS-403 Core Drill 27 ampS - 3 SpeeD
New Two Year warra arraNTY NTY!
hiGh SpeeD 3rD Gear for hiGh proDuCTioN of Small DiameTer holeS
The pro’S uTiliTY Core Drill GreaT wheN power iS limiTeD
$
2,410
$
2,725 ListPart$3,895 DR1018
Sale Net
Sale Net
Does not include bit
Motor Base Style RPM (no Load) Bit Capacity Column Length
R2031 Angle 380/1000/1700 14-16" Max. 39.4"
List $3,445 Part DR1003
Motor Base Style RPM (no Load) Bit Capacity Column Length
Does not include bit
R2231 Fixed 300/800/1400 16" 39.4"
TS-603 Core Drill 27 amp ampS - 3 SpeeD
New Two Year warraNTY!
The pro’S alTerNaTive To hYDrauliCS The hawG -- The moST powerful 115 volT Core Drill oN The markeT $ List $8,595
6,015 Sale Net
Part DR1010
Base Style Anchor Motor R2531 RPM (No Load) 150/300/600 Bit Capacity (Max.) 26”
Does not
Place Your Order Now! w w w. CSD A .ORG
Phone: 866-688-1032 Fax: 877-220-4777
c on c r e t e o p e n i n g s | 6 3
866-688-1032 DIAMOND TOOLS & EQUIPMENT
Director’s Dialogue
Regulations – Fight Them or Make Them Work for You Patrick o’brien Executive Director
t seems that almost anywhere you look these days, there is a new
I
Ten Best Practices have also been developed. These documents cover
regulation dictating how we should live our lives or run our busi-
slurry disposal, maintenance, remote control, ground penetrating radar,
nesses. In my early days with CSDA, there was much reluctance
polished concrete floors, green concrete and hi-cycle equipment.
on the part of anyone to put in writing anything that detailed how
In 2006 CSDA began to actively work with OSHA through a formal
work was to be done. Avoiding the issue was the status quo in the
Alliance. When the idea of forming a working Alliance with OSHA was first
early days. This strategy worked for quite some time since sawing and
introduced, many thought that CSDA was crazy to be working with the
drilling was such a small segment of the construction industry and
“enemy.” However, the working relationship has proved to be excellent
under the radar of most regulating organizations. However, things
and has produced six Best Practices covering highway work zones, silica,
have changed and continue to do so at a faster pace than ever before.
defensive driving, electrical safety, scaffolding and ladders. In addition,
Quite some time ago, CSDA began to document sawing and
through CSDA’s involvement with the Design for Safety workgroup, a
drilling procedures. This began by updating a number of older
toolbox safety talk has been produced on sprains and strains.
standards and specifications. Some felt that once this updating
CSDA also has developed its own library of Toolbox Safety Tips (TSTs)
was accomplished, all would be well and the CSDA Standards &
for sawing and drilling contractors to use as part of any company’s safety
Specifications Committee could dissolve. Fortunately, others saw a
program. Ninety-four TSTs can be used to promote workplace safety and
future that would require continued work in this area.
as references in employee safety meetings.
CSDA embarked on a plan to regularly introduce new Standards
As CSDA gets ready to celebrate its 40th Anniversary, great strides
and Specifications, Tolerances and Best Practices. Today, CSDA offers
have been made documenting the practices of the sawing and drilling
eight specifications that cover all cutting disciplines, including the
industry. This effort will only intensify in the future and the Standards and
newest area of polishing concrete. Three standards cover the blade
Specifications Committee is hard at work on a number of new documents.
application code, bolt together core bits and continuous tubing.
The decision by CSDA to head down this path many years ago was the
Tolerances were developed in conjunction with the International
right one for members and the industry. It also had a secondary benefit
Association of Concrete Drillers and Sawers and address tolerances
of increasing the professionalism of the industry, which has been a great
and limits to sawing and drilling as well as basic parameters for
asset when working with specifiers.
the equipment.
6 4 | JU NE.1 1
Hilti Lifetime Service
Service that lasts a lifetime. Hilti. Outperform. Outlast.
Hilti Diamond Systems 1-800-879-4000 www.us.hilti.com • www.hilti.ca *Some limitations apply. Contact Hilti for details.
If a tool goes down, Hilti understands you need to get it back on the job quickly. That’s why Hilti repairs and returns most tools in less than 5 business days, including transit time. With Hilti Lifetime Service, you incur absolutely no repair costs for up to the lesser of 2 years or 200 hours from the date of purchase.* Industry leading repair service – that’s the Hilti difference.
Two for one.
Husqvarna’s new electric wire saw, the CS 10, uses components from the WS 440 HF or the WS 482 HF electric wall saws to create a powerful and flexible saw system for cutting through larger concrete structures. The ability to use a wire saw and a wall saw interchangeably means increased efficiency and a highly cost-effective system. The CS 10 can be easily coupled to the wall saw’s operating unit, track and power supply so switching between the two saws is quick and easy. The saw unit has the option of mounting on either side of the wall saw track and the wire can be rotated in both directions, making it more flexible. The variable wire speed takes into account wire type and material to be cut, resulting in optimal performance. The CS 10 wire saw is easy to maneuver and is controlled by a remote control which allows the operator to operate the machine easier and allows greater freedom to move around the work site. The system can be used for all types of wire saw jobs including foundations, bridges and thick walls.
Wire saw and a wall saw in a single system.
HUSQVARNA CONSTRUCTION PRODUCTS 17400 West 119th Street • Olathe, Kansas 66061 • T 800-845-1312 • F 800-257-9284 2077 Bond Street • North Bay, Ontario P1B 8J8 • T 800-461-9589 • F 800-728-1907 www.husqvarnacp.com Copyright © 2011 Husqvarna AB (publ.). All rights reserved. Husqvarna is a registered trademark of Husqvarna AB (publ.).