Device No.: YSD2009260-F Rev.:
2.0
LED Indicator Display Specifications Model No.: YSD-230AG
June 18, 2009 ★ Specifications are subject to changes for improvement without advance notice. Proprietary data, drawings, company confidential all rights reserved. A d d r e s s : 1 2 F, N o . 1 2 0 - 1 3 , S e c . 3 , C h u n g - S a n R d . , C h u n g - H o C i t y, Ta i w a n , R . O . C . 2 3 5 Tel: 886 2 2221 3358, Fax: 886 2 2221 3821 E-Mail: yiowchie@ms19.hinet.net Website: www.yiowchie.com.tw
Device No.: YSD2009260-F Rev.:
2.0
Part Number: YSD-230AG ● Features:
● Applications:
1. Low power requirement.
1. Audio equipment.
2. Excellent characters appearance.
2. Instrument panels.
3. Solid state reliability.
3. Digital read out display.
4. Categorized for luminous intensity. 5. This product don't contained restriction substance, compliance ROHS standard.
● Package Dimension: .275) 5.40(.21 2)
60.20(2.37)
56.80(2.3")
10°
69.70(2.744)
32.40(1
1,5
6.0±0.5
11.80(.464)
47.80(1.881)
2.54*4=10.16
Part Number YSD-230AG
ψ0.50(.019)
PIN 1
A
A F
B
G
E
7
B 6
C
D
4
E
3
F
2
G 9
DP
10
C D
DP
Chip Material
Emitting Color
GaP
Green
C.C or C.A C.A
NOTES: 1. All dimensions are millimeters (inches). 2. Tolerance is ±0.25mm (0.01") unless otherwise specified. 3. Specifications are subject to change without notice. Prepared by: Lydia Chen
Page 1 of 7 June 18, 2009
Tel: 886 2 2221 3358, Fax: 886 2 2221 3821 E-Mail: yiowchie@ms19.hinet.net Website: www.yiowchie.com.tw
8
Device No.: YSD2009260-F Rev.:
2.0
Part Number: YSD-230AG ●Absolute Maximum Rating
(Ta=25℃)
Item
Symbol
Absolute Maximum Rating
Unit
Continuous Forward Current Peak Forward Current (1/10 Duty Cycle,0.1ms Pulse Width) Power Dissipation Reverse Voltage Derating Linear From 50℃
IF
40
mA
IFP
100
mA
PD VR / Top Tstg
100 5 0.4 -40℃~80℃ -40℃~80℃
mW V mA/℃ ℃ ℃
Operating Temperature Storage Temperature Lead Soldering Temperature (1.6mm(.063”)From Body)
Tsol
260℃ FOR 5 SECONDS
●Initial Electrical/Optical Characteristics Item Forward Voltage Reverse Current Luminous Intensity Peak Wavelength Spectral Line Half-width
Symbol VF IR IV λp △λ
Condition IF=20(mA) VR=5(V) IF=20(mA) IF=20(mA) IF=20(mA)
(Ta=25℃) Min 1.7 / 7 563 25
Typ 2.2 / 15 568 30
Max 2.6 100 32 573 35
Unit V μA mcd nm nm
※Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve.
●TYPICAL INTIAL OPICAL/ELECTRICAL CHARACTERISTICS Please refer to Figures: in Page 2
●OUTLINE DIMENSIONS AND MATERIALS Please refer to drawing: in Page 1
Prepared by: Lydia Chen
Page 2 of 7 June 18, 2009
Tel: 886 2 2221 3358, Fax: 886 2 2221 3821 E-Mail: yiowchie@ms19.hinet.net Website: www.yiowchie.com.tw
Device No.: YSD2009260-F Rev.:
2.0
Part Number: YSD-230AG ●Typical Electro-Optical Characteristic Curves: (Ta=25℃ Ambient Temperature Unless Otherwise Noted) Fig1. Spectral Radiance (Peak@568nm)
Relative Radiant Intensity
1 .0
0 .8
0 .6
0 .4
0 .2
0 .0 460 480 500 520 540 560 580 600 620 640 660 680 700 720 740
Wavelength λP (nm) Fig2.Forward Current vs. Forward Voltage Forward Current IF (mA)
40 30 20 10 0
1.5
1.7
1.9 2.5 2.1 2.3 Forward Voltage (Vf)-Volts
2.7
2.9
Relative Luminous Intensity (LOP@ 20mA=1)
Fig3. Relative Luminous Intensity vs. Forward Current
3 2.5 2 1.5 1 0.5 0
0
10
20
30
40
50
Forward current IF (mA) Prepared by: Lydia Chen
Page 3 of 7 June 18, 2009
Tel: 886 2 2221 3358, Fax: 886 2 2221 3821 E-Mail: yiowchie@ms19.hinet.net Website: www.yiowchie.com.tw
Device No.: YSD2009260-F Rev.:
2.0
Part Number: YSD-230AG ●RELIABILITY TEST: Classification
Test Item
MIL-STD-750:1026 MIL-STD-883:1005 JIS C 7021 :B-1
Operation Life
High Temperature High Humidity
Result
Connect with a power IF=25mA Ta=Under room temperature
0/10
Test time=1,000hrs(-24hrs,+72hrs) Ta=65℃±5℃ 0/10
RH=90%~95%
:B-11 Test time=240hrs±2hrs Ta=65℃±5℃
High Temperature
0/10
RH=90%~95%
/
High Humidity Reverse Bias
Test time=500hrs(-24hrs,+48hrs)
High Temperature Storage
MIL-STD-883:1008 JIS C 7021 :B-10
Low Temperature Storage
JIS C 7021 :B-12
Temperature Cycling
Environmental Test
Test Conditions
MIL-STD-202:103B JIS C 7021
Storage
Endurance Test
Reference Standard
Thermal Shock
Solder Resistance
Solder ability
High Ta=85℃±5℃
0/10
Test time=1,000hrs(-24hrs,+72hrs) Low Ta=-35℃±5℃
0/10
Test time=1,000hrs(-24hrs,+72hrs) MIL-STD-202:107D MIL-STD-750:1051 MIL-STD-883:1010 JIS C 7021 :A-4
-35℃ ~25℃ ~85℃ ~25℃
MIL-STD-202:107D MIL-STD-750:1051 MIL-STD-883:1011
85℃ ±5℃ ~ -35℃ ±5℃
30min 5min 30min 5min
0/10
Test Time= 10 cycle
10min
MIL-STD-202:201A MIL-STD-750:2031 JIS C 7021 :A-1 MIL-STD-202:208D MIL-STD-750:2026 MIL-STD-883:2003 JIS C 7021 :A-2
10min
0/10
Test Time=10cycle T.sol=260±5℃
0/10
Dwell Time=10±1sec. T.sol=230±5℃ Dwell Time=5±1sec.
●JUDGMENT CRITERIA OF FAILURE FOR THE RELIABILITY Measuring items
Symbol
Measuring conditions
Judgment criteria for failure
Forward voltage
VF(V)
If=20mA
Over Mx1.2
Reverse current
Ir(μA)
Vr=5V
Over Mx2
Luminous intensity
Iv(mcd)
If=20mA
Below Nx0.5
Note: 1. M means the upper limit of specified characteristics. N means initial value. 2. Measurement shall be taken between 2 hours and after the test pieces have been returned to normal ambient conditions after completion of each test.
Prepared by: Lydia Chen
Page 4 of 7 June 18, 2009
Tel: 886 2 2221 3358, Fax: 886 2 2221 3821 E-Mail: yiowchie@ms19.hinet.net Website: www.yiowchie.com.tw
Device No.: YSD2009260-F Rev.:
2.0
Part Number: YSD-230AG ●Application Notes for LED Display (Ⅰ) Lead Forming Method ◆ Avoid forming a lead pin with the lead pin base as a fulcrum: be sure to hold a lead pin firmly when forming. ◆ Lead pins should be formed before soldering.
No
Yes (Ⅱ) Soldering Conditions
Solder the lead pins under the following conditions. Type of Soldering 1.Manual Soldering 2.Wave Soldering 3.Reflow Soldering
Conditions 295℃±5℃, within 3 seconds 260℃±5℃, within 5 seconds Preheating 70℃to 80℃, within 30 seconds Soldering 245℃±5℃, Within 5 seconds
(Ⅲ) Cleaning (1)Solvents The package resin may be penetrated by solvents used in cleaning. Refer to the table below for
usable solvents. Solvent Ethyl alcohol Isopropyl alcohol Chlorosen Acetone Trichloroethylene
Usable Yes Yes No No No
(Notes) ◆ There is a world-wide movement to restrict the use of chlorofluorocarbon (CFC) based solvents and we recommend that you avoid their use. However, before using a CFC substitute solvent,
carefully check that it will not penetrate the package resin. Prepared by: Lydia Chen
Page 5 of 7 June 18, 2009
Tel: 886 2 2221 3358, Fax: 886 2 2221 3821 E-Mail: yiowchie@ms19.hinet.net Website: www.yiowchie.com.tw
Device No.: YSD2009260-F Rev.:
2.0
Part Number: YSD-230AG (2) Cleaning Methods Cleaning Method
Usable
Solvent cleaning
Yes
Ultrasonic cleaning
Yes/No
Remarks Immersion up to one minute at room temperature Test the cleaning under actual conditions and check for abnormalities before actual use.
(Notes) ◆ The affect on the device from ultrasonic cleaning differs depending on the size of the cleaning bath, ultrasonic output, duration, board size and device mounting method. Test the cleaning
method under actual conditions and check for abnormalities before actual use. ◆ Cleaning with water is not allowed with the lead pins resin-tabulated: water may remain, thus causing rust to the lead pins. ◆ Please contact our representative before using a cleaning solvent or method not given above.
(Ⅳ) Warranty ◆ YIOW CHIE warrants that its LED’s conform to the foregoing specifications and that YIOW CHIE will convey good title to all LED's sold. ◆ YIOW CHIE disclaims all other warranties including the implied warranties of merchantability and fitness for a particular purpose. ◆ In the event any LED supplied by YIOW CHIE is found not to conform to the foregoing specifications within ninety days of receipt ,YIOW CHIE will repair or replace the LED, at
YIOW CHIE’s option, provided that User. (1) Promptly notifies YIOW CHIE in writing of the details of the defect. (2) Ships the LED at User’s expense to YIOW CHIE for examination. (3) The defect is due to the negligence of YIOW CHIE and not mishandling or misuse by User. ◆ YIOW CHIE cannot take any responsibility for any troubles that are caused by using the LED's at conditions exceeding our specifications. ◆ These specifications are applied only when a LED stands alone and it is strongly recommended that the User of the LED confirms the properties upon assembly. YIOW CHIE is not responsible
for failures caused during and after assembling. ◆ These LED’s are designed and manufactured for standard applications such as electric home appliances, communication equipment, office equipment, electronic instrumentation and so on. ◆ It is recommended to consult with YIOW CHIE in advance if User's application requires any particular quality or reliability which concerns human life. Examples would medical equipment,
aerospace applications, traffic signals, safety system equipment and so on. ◆ YIOW CHIE’s liability for defective lamps shall be limited to replacement and in no event shall YIOW CHIE be liable for consequential damages or lost profits.
Prepared by: Lydia Chen
Page 6 of 7 June 18, 2009
Tel: 886 2 2221 3358, Fax: 886 2 2221 3821 E-Mail: yiowchie@ms19.hinet.net Website: www.yiowchie.com.tw
Device No.: YSD2009260-F Rev.:
2.0
Part Number: YSD-230AG (â…¤) Others
(1) Both parties shall sincerely try to find a solution when any inconvenience is found in these specifications. (2) The User’s approval shall be required when YIOW CHIE modifies the design or the manufacturing process which would affect the characteristics, performance reliability and so on. (3) These specifications can be revised on mutual agreement. (4) YIOW CHIE understands that User accepts the content of this specification, if User does not return these specifications with your signature within 3 weeks after your receipt.
--END of SPECIFICATIONS--
Prepared by: Lydia Chen
Page 7 of 7 June 18, 2009
Tel: 886 2 2221 3358, Fax: 886 2 2221 3821 E-Mail: yiowchie@ms19.hinet.net Website: www.yiowchie.com.tw