The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH
AbuDhabi
Operates a management system in accordance with the requirements of ISO 9001 : 2015 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
Management system as per C E R T I F I CAT E
ISO 14001 : 2015
The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH AbuDhabi
Operates a management system in accordance with the requirements of ISO 14001 : 2015 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
C
E R T I F I CAT E
Management system as per
ISO 45001 : 2018
The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH AbuDhabi
operates a management system in accordance with the requirements of ISO 45001 : 2018 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
PERRYJOHNSONLABORATORY ACCREDITATION,INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
Chemical, Electrical, Mechanical, Thermodynamic, Time and Frequency, and Flow Meter Calibration (As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
Initial Accreditation Date: Issue Date: Expiration Date: October 20, 2020 March 3, 2023 April 30. 2025
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Chemical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE CALIBRATION AND MEASUREMENT
pH MeterF 4.01 pH
pH
pH
Conductivity MeterF 1.33 µS/cm
903 µS/cm
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
pH at 25ºC
µS/cm
Density MeterF 0.99 910 g/mL at 15 °C 0.01 % of reading
0.99 702 g/mL at 25 °C
Turbidity MeterF 0.5 NTU
Equipment to Measure Min
Reid Vapor Pressure
Equipment to Measure Sulfur Content X-RayF
Meter
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Buffer Solution / CEC-CAD-PRD-EN-0061
Conductivity Standards / CEC-CAD-PRD-EN-0059
Density Reference Standard / CEC-CAD-PRD-EN-0052 0.99 821 g/mL at 20 °C
NTU
Using Formazin Turbidity Standards 40 NTU 8 NTU
NTU 2 NTU 400 NTU 8 NTU
000 NTU
Water Mark Karl Fischer Water Standard / ASTM E203-16
Vapor Pressure Standard / ASTMP-124-03-VAP & ASTM D323
Sulfur Reference Standard /ASTM D4294
Colour Ref Standard / ASTM D 6045 and D1500 Open Cap Flash Point MeterF 84 ºC
Close Cap Flash Point MeterF 64 ºC
Smoking Point MeterF
Pour Point MeterF
HydrometersF 0.5 to 1
Shelling (Density of Gas)F 1.256 g/L
Gas – ChromatographyF C1 – C6
Accreditation is granted to the facility to perform the following calibrations: Issue: 3/2023
Flash Point Reference Standard Field Metrology Well 9142 / ASTM-D-92
Flash Point Reference Standard Field Metrology Well 9142 / ASTM-D-93
Smoking Point Reference Standard / ASTM-D-1322
Pour Point Reference Standard/ ASTM-D-97
DAW-ACETONE-TOLUENE / ASTM-368
Pure Nitrogen / IP-59
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Chemical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
MeterF
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Equipment To Output DC VoltageFO
Equipment To Output AC Voltage
the Listed FrequenciesFO
Equipment To Output AC Voltage At the Listed FrequenciesFO
Equipment To Output AC Voltage At the Listed FrequenciesFO
3
50 kHz to 100 kHz
100 kHz to 300 kHz
Issue: 3/2023
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Viscosity Reference Standard and ASTM D445,D446,D2171, CECCAD-PRD-EN-0062
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Fluke 8846A / OEM Manual, EUROMET cg-15
Page 3 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE RANGE OR NOMINAL DEVICE
Equipment To Output AC Voltage At the Listed FrequenciesFO
3
5
Fluke 8846A / OEM Manual, EUROMET cg-15
Equipment To Output AC Voltage
At the Listed FrequenciesFO 3
Equipment To Output AC Voltage
At the Listed FrequenciesFO
3
100 kHz to 300 kHz
Equipment To Output AC Voltage
At the Listed FrequenciesFO
Issue: 3/2023
Page 4 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Equipment To Measure Output ResistanceFO up to 10 Ω 0.12 mΩ/Ω + 3 mΩ Fluke 8846A / OEM Manual, EUROMET cg-15
10 Ω to 100 Ω 0.12 mΩ/Ω + 4 mΩ
100 Ω to 1 kΩ 0.12 mΩ/Ω + 10 mΩ
1 kΩ to 10 kΩ 0.12 mΩ/Ω + 100 mΩ
10 kΩ to 100 kΩ 0.12 mΩ/Ω + 1 Ω
100 kΩ to 1 MΩ 0.12 mΩ/Ω + 10 Ω
1 MΩ to 10 MΩ 0.46 mΩ/Ω + 100 Ω
1 MΩ to 10 MΩ 0.46 mΩ/Ω + 100 Ω
10 MΩ to 100 MΩ 9 mΩ/Ω + 10 kΩ
100 MΩ to 1 GΩ 23 mΩ/Ω + 100 kΩ
Equipment To Measure Output DC CurrentFO
5 µA to 100 µA 0.6 mA/A + 25 nA
100 µA to 1 mA
0.6 mA/A + 50 nA
1 mA to 10 mA 0.6 mA/A + 2 µA
10 mA to 100 mA 0.6 mA/A + 5 µA
100 mA to 1 A 0.6 mA/A + 0.2 mA
1 A to 3 A 1.2 mA/A + 0.6 mA
3 A to 10 A 1.7 mA/A + 0.8 mA
10 A to 40 A 2.3 % of reading + 50 mA
40 A to 400 A 2.3 % of reading + 0.5 A
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz 5 µA to 100 µA 1.2 % of reading + 40 nA
5 Hz to 10 Hz 5 µA to 100 µA 0.4 % of reading + 40 nA
10 Hz to 5 kHz 5 µA to 100 µA 0.1 % of reading + 40 nA
5 kHz to 10 kHz
5 µA to 100 µA 0.2 % of reading + 250 nA
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz
5 Hz to 10 Hz
5 Hz to 10 Hz
10 Hz to 5 kHz
5 kHz to 10 kHz
100 µA to 1 mA 1.2 % of reading + 0.4 µA
100 µA to 1 mA 0.4 % of reading + 0.4 µA
100 µA to 1 mA 0.4 % of reading + 0.4 µA
100 µA to 1 mA 0.1 % of reading + 0.4 µA
100 µA to 1 mA 0.2 % of reading + 2.5 µA
Fluke 325 / OEM Manual, EUROMET cg-15
Fluke 8846A / OEM Manual, EUROMET cg-15
Issue: 3/2023 This supplement is in conjunction with certificate #L23-199 Page 5 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Equipment To Output AC Current At the Listed FrequenciesFO
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
3 Hz to 5 Hz 1 mA to 10 mA 1.2 % of reading + 4 µA
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz 10 mA to 100 mA
5
to
10 Hz to 5 kHz 10 mA to 100 mA 0.1 % of reading + 40 µA
5 kHz to 10 kHz 10 mA to 100 mA 0.2 % of reading + 250 µA
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz 100 mA to 1 A 1.2 % of reading + 0.4 mA
5 Hz to 10 Hz
mA to 1 A 0.4 % of
+ 0.4 mA 10 Hz to 5 kHz
5 kHz to 10 kHz
Equipment To Output AC Current At the Listed FrequenciesFO
mA to 1 A
mA to 1 A
% of reading + 7 mA
3 Hz to 5 Hz 1 A to 3 A 3 Hz to 5 Hz
5 Hz to 10 Hz 1 A to 3 A 5 Hz to 10 Hz
10 Hz to 5 kHz 1 A to 3 A 10 Hz to 5 kHz
5 kHz to 10 kHz 1 A to 3 A 5 kHz to 10 kHz
Equipment To Output AC Current
At the Listed FrequenciesFO
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Fluke 8846A / OEM Manual, EUROMET cg-15
3 Hz to 5 Hz 3 A to 10 A 2.3 % of reading + 6 mA
5 Hz to 10 Hz 3 A to 10 A 1.3 % of reading + 6 mA
10 Hz to 5 kHz 3 A to 10 A 0.2 % of reading + 6 mA
5 kHz to 10 kHz 3 A to 10 A 0.4 % of reading + 70 mA
5 kHz to 10 kHz 3 A to 10 A 0.4 % of reading + 70 mA
Issue: 3/2023
Page 6 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
NOMINAL
Equipment To Output AC Current At the Listed FrequenciesFO Fluke 325 / OEM Manual, EUROMET cg-15
40 Hz to 65 Hz
Equipment To Output AC Current At the Listed FrequenciesFO
Capacitor and Equipment to Measure Output
CapacitanceFO
of
+
pF
nF to 100 nF
% of reading + 500 pF 100 nF to 1µF
µF to 10 µF
% of reading + 5 nF
% of reading + 50 nF
µF to 100 µF 1.2 % of reading + 500 nF 100 µF to 1 mF 1.2 % of reading + 5 µF 1 mF to 10 mF 1.2 % of reading + 50 µF 10 mF to 100 mF 4.6 % of reading + 200 µF
Equipment to Measure DC VoltageFO Up to 329.999 mV 0.11 mV/V
µV
10 V to 329.999 V 0.1 mV/V + 1.5 mV
100 V to 1 020 V 0.1 mV/V + 5.5 mV
Equipment to Measure DC CurrentFO Up to 329.99 µA 0.7 mA/A + 0.1 µA 0.33 mA to 3.29 mA 0.6 mA/A + 0.25 µA
3 3 mA to 32.9 mA 0.48 mA/A + 1.25 µA 33 mA to 329.99 mA 0.48 mA/A + 16.5 µA
0.33 A to 1.099 9 A 1.4 mA/A + 220 µA 1.1 A to 2.999 9 A 1.8 mA/A + 220 µA
3 A to 10.999 A 2.3 mA/A + 2.5 mA
11 A to 20.500 A 4.8 mA/A + 3.75 mA
55 A to 150 A 0.36 % of reading + 11 mA
/ OEM Manual, EUROMET cg-15
16 A to 55 A 0.34 % of reading + 11 mA Fluke 5080A Via 50-Turn Current Coil / OEM Manual, EUROMET cg-15
150 A to 550 A 0.41 % of reading + 125 mA
550 A to 1 025 A 0.65 % of reading + 188 mA
Issue: 3/2023 This supplement is in conjunction with certificate #L23-199 Page 7 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Equipment to Measure Resistance, Fixed Points
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Fluke 5080A / OEM Manual, EUROMET cg-15
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Equipment To Measure AC Voltage
At The Listed Frequencies
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Issue: 3/2023
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Fluke 5080A / OEM Manual, EUROMET cg-15 45
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Equipment To Measure AC Current
At The Listed FrequenciesFO
Equipment To Measure AC
Equipment To Measure AC Current At
Equipment To Measure AC Current At The Listed FrequenciesFO 45
Equipment To Measure
Equipment To Measure AC Current
At The Listed FrequenciesFO
45 Hz to 65 Hz 1.1 A to 2.999 9 A
Issue: 3/2023
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
Equipment To Measure AC Current At The Listed FrequenciesFO
45
Equipment To Measure AC Current At The Listed FrequenciesFO
Equipment To Measure AC Current
At The Listed FrequenciesFO
Equipment To Measure
Fluke 5080A / OEM Manual, EUROMET cg-15
Equipment To Measure AC Current At The Listed Frequencies
Issue: 3/2023
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Mechanical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
Mass Flow Meter (Water)FO 3 614 kg/h to 6 820 kg/h
52 160 kg/h to 87 100 kg/h
163 000 kg/h to 272 000 kg/h
415 179 kg/h to 545 000 kg/h
415 179 kg/h to 545 000 kg/h
904 211 kg/h to 1 470 000 kg/h
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
3/2023
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Coriolis Flow Meter1/2" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 2" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 3" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 4" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 6" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 8" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Mechanical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED Volumetric Flow
Accreditation is granted to the facility to perform the following calibrations: Issue: 3/2023
Coriolis Flow Meter 1/2" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 2" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 3" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 4" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 6" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 8" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Oil & Water Density within DPT
Density Calibration Stand
Flow Meter 1/2" (in) API MPMS 4.5-2016 API MPMS 4.8-2013
Coriolis Flow Meter 2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 3" (in) API MPMS 4.5-2016
4.8-2013
Coriolis Flow Meter 4" (in)
API MPMS 4 5-2016
API MPMS 4.8-2013
904
Coriolis Flow Meter 8" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Volumetric Flow Rate (Petroleum)FO 60.57 L/min to 113.6 L/min 0.056 % of reading
870.6 L/min to 1 317 L/min
2 729 L/min to 4 542 L/min
6 916 L/min to 9 085 L/min
6 916 L/min to 9 085 L/min
15 085 L/min to 24 378 L/min
Prover Base Volume (Pipe prove, Compact Prover, Tank Prover)FO
Calibration according to: ISO 4269:2001 (Incremental method using volumetric meters) OIML R 63:1994 “Petroleum measurement tables” OIML R 80-1:2009 “Road and rail tankers with level gauging. Part 1: Metrological and technical requirements”
Calibration medium: Liquid hydrocarbons (gasoline, diesel oil, biodiesel, JET A1) Calibration performed on site
Issue: 3/2023 This supplement is in conjunction with certificate #L23-199 Page 13 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein
Phone: +1(801) 326-4626
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Vertical Cylindrical TanksFO
50 m3
200
2
% of reading
Torque Wrenches /Torque DriversF
500 m3 0.13 % of reading
2 000 m3 0.09 % of reading
10 000 m3 0.07 % of reading
20 000 m3 0.06 % of reading
75 000 m3 0.06 % of reading
120 000 m3 0.06 % of reading
200 m3 0.16 % of reading
2 000 m3 0.13 % of reading
10 000 m3 0.09 % of reading
40 000 m3 0.06 % of reading
75 000 m3 0.06 % of reading
120 000 m3 0.06 % of reading
(Above 200 m3 Min tank diameter: 5m) of nominal tank volume
5 nm to 500 nm 1 % of reading
Liquid Volume/Horizontal Cylindrical TanksFO
Accreditation is granted to the facility to perform the following calibrations: Issue: 3/2023
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Geometric method using strapping tape
Calibration according to: ISO 7507-1:2003 (Strapping Method)
Calibration performed on site
500 nm to 1 000 nm 1 % of reading
1 000 nm to 2 000 nm 1 % of reading
Up to 400 m3 Maximum tank diameter: 4m Maximum tank length: 30m
0.065 % of nominal tank volume
Geometric method using total station
Calibration according to: ISO 7507-3:2006 (Optical triangulation method with reference circumference) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site
Geometric method using total station
Calibration according to: ISO 7507-4:2010 (Internal electrooptical distance ranging method) ISO 7507-1:2003 (Remaining measurements)
Temperature Sensors And Temperature Measuring InstrumentsFO
Thermo Hygrometer at
To
Time and Frequency MEASURED INSTRUMENT, QUANTITY OR GAUGE
TachometerFO
Equipment To
Output FrequencyFO
Fluke 9132 / OIML R 147 / ASTM E2847
PRT and TC Sensors / EURAMET cg-20 / EN 60068-3-5
PRT And TC Sensors Via Fluke 8846A / ASTM E2488-9
FLUKE 9142, 9144, Semi Standard PRT, Fluke 8846A / ASTM-E2877, EA 10/11, OIML R84
Stability Test Chamber ZF120 / ASTM E126
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Lutron DT-2269 / OEM Manual, EUROMET cg-15
Fluke 8846A / OEM Manual, EUROMET cg-15
1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree
Issue: 3/2023 This
Page 16 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity.
3. The presence of a superscript F means that the laboratory performs calibration of the indicated parameter at its fixed location Example: Outside MicrometerF would mean that the laboratory performs this calibration at its fixed location.
4. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations Example: Outside MicrometerFO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations.
5. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location.
Issue: 3/2023
PERRYJOHNSONLABORATORY ACCREDITATION,INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
Mechanical Testing
(As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA) 755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
Initial Accreditation Date: Issue Date: Expiration Date: October 20, 2021 March 3, 2023 April 30, 2025
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
FIELD OF TEST
MechanicalFO
ITEMS, MATERIALS OR PRODUCTS TESTED
Pressure Relief Valve (Pneumatic)
Pressure Relief Valve (Hydraulic)
SPECIFIC TESTS OR PROPERTIES MEASURED
Relief Pressure Valve
Relief Pressure Valve
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
Safety Valve Test Bench / API-527
ASME PTC-25
Safety Valve Test Bench / API-527
ASME PTC-25
RANGE (WHERE APPROPRIATE) AND DETECTION LIMIT
Up to 700 bar
Up to 1 200 bar
1. The presence of a superscript FO means that the laboratory performs testing of the indicated parameter both at its fixed location and onsite at customer locations. Example: Outside MicrometerFO would mean that the laboratory performs this testing at its fixed location and onsite at customer locations.
3/2023
PERRYJOHNSONLABORATORY ACCREDITATION,INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system
Inspection Body (Category-A) (As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
Initial Accreditation Date: Issue Date: Expiration Date: October 20, 2020 March 3, 2023 April 30, 2025
Accreditation No.
Certificate No.: 111664 L23-198
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Category A
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: 801-326-4626
Accreditation is granted to the facility to perform the following inspections:
Contact Name: Mr. Shahriyar Majlesein Phone: 801-326-4626
Accreditation is granted to the facility to perform the following inspections:
FIELD OF INSPECTION
Pipelines
TYPES OR RANGES OF INSPECTIONS
Piping
VT Set/NDT Set
1) Inspection Body Classifications (Type A, B or C)
SPECIFICATION, STANDARD METHOD, OR TECHNIQUE USED
ASME B31.3
Type A- An inspection body providing third party inspections
Type B- An inspection body providing first party inspections, second party inspections, or both, which forms a separate and identifiable part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services only to its parent organization (in-house inspection body)
Type C- An inspection body providing first party inspections, second party inspections, or both, which forms an identifiable but not necessarily a separate part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services to its parent organization or to other parties, or to both
Name of CAB
CITADEL OILFIELD SERVICES
Address Abu Dhabi - Al Taweelah - KLP FZ No:29, Al Taweelah, Abu Dhabi
This cer ficate was issued based on the request of the conformity assessment body without any responsibility to be bared by Ministry of Industry and Advanced Technology toward others.
This is an electronic cer ficate and does not require stamp and signature Cer ficate will be invalid in case of any modifica on
Cer fica on Number
Name of CAB
CITADEL OILFIELD SERVICES
Address Abu Dhabi - Al Taweelah - KLP FZ No:29, Al Taweelah, Abu Dhabi
Calibra on Laboratory
This cer ficate was issued based on the request of the conformity assessment body without any responsibility to be bared by Ministry of Industry and Advanced Technology toward others.
This is an electronic cer ficate and does not require stamp and signature Cer ficate will be invalid in case of any modifica on
This permission was issued after conducting the compliance audit and ensuring the following:
• Compliance with the requirements of Law No. 2/2010 and its Administrative Order no. 267/ 2011 regarding organizing the work of conformity assessment bodies operating in the Emirate of Dubai,
• Compliance with all conditions and instructions issued by the Emirates International Accreditation Centre.
Notes:
• This permission applies only to the scopes mentioned above.
• The validity of this permission is one year only and it should be renewed for the non accredited conformity bodies before 15 days from the date of expired.
• It is not permitted for the Conformity Assessment Body to practice activities or to use EIAC Accreditation Symbol where accreditation is mandatory unless it is accredited by EIAC
For more information about the Mandatory Accreditation Scopes; please visit EIAC website: www.eiac.gov.ae
Conformity Assessment Body should submit an application to obtain accreditation within the first year of getting this permit according to the Law no. 2/ 2010. Emirates International Accreditation Centre is entitled to take all legal actions in case of violation of any of the conditions mentioned in Law 2/2010 and its Administrative Order no. 267/ 2011.
Is an Executive Member of the International Lifting Equipment Engineers Bureau. The organisation has been audited in accordance with ILEEB's approved code of practice on the following sections :
Membership Number. : IL-1856
Issue Date : 04/07/2022
Expiry Date : 03/07/2023
-
validate@ileeb.com
Bowan Technical Director
Justin
Is an Executive Member of the International Lifting Equipment Engineers Bureau. The organisation has been audited in accordance with ILEEB's approved code of practice on the following sections :
Membership Number. : IL-1856
Issue Date : 04/07/2022
Expiry Date : 03/07/2023
-
validate@ileeb.com
Bowan Technical Director
Justin
ANNUAL MEMBERSHIP CERTIFICATE 2021
We
This certifies all requirements for the designation as an OSHAcademy
Authorized Training Provider has been met
by
Citadel Engineering Company
This organization has met all qualifications and is designated as an OSHAcademy Authorized Training Provider (ATP). They may perform all activities necessary, as defined by the Authorized Training Provider Manual, to conduct OSHAcademy training during the registration period and in the geographical region(s) specified below:
Steven J. Geigle, M.A., CET, CSHM Director
OSHAcademy Safety & Health Training
OSHAcademy training conforms to OSHA Training Standards and ANSI Z490.1-2009, Criteria for Accepted Practices in Safety, Health and Environmental Training. OSHAcademy training is recognized by the National Safety Management Society (NSMS) and the Institute for Safety and Health Training (ISHM).
CERTIFICATE OF ACCREDITATION
This is to accredit the named organization as having had the adequacy of their program verified for the scope shown below in accordance with the applicable rules of The American Society of Mechanical Engineers (ASME) Standard for Qualifications for Authorized Inspection. The accreditation granted by this certificate is subject to the provisions of the agreement set forth in the application.
COMPANY:
Citadel Engineering Company Inspection
4541 S 700 E Ste 250 Salt Lake City, Utah 84107 United States
SCOPE:
Authorized Inspection Agency for performance of inspection activities controlled from the above location to cover Sections I; IV; VIII, Divisions 1, 2 & 3; X; and XII of the ASME Boiler and Pressure Vessel Code in accordance with QAI-1
AUTHORIZED:
EXPIRES: May 24, 2027
CERTIFICATE NUMBER: AIA-145
Board Chair, Conformity Assessment
Senior Director, Engineering Operations
Certificate of Acceptance
This is to certify that
Citadel Engineering Company Inspection
4541 S 700 E Ste 250
Salt Lake City, Utah 84107
United States
is accepted as an Authorized Inspection Agency in accordance with the provisions of NB-360, National Board Acceptance of Authorized Inspection Agencies (AIA) Accredited by ASME. The scope of this acceptance includes: Accreditation to provide third party inspection services for repairs and alterations in accordance with the National Board Inspection Code.
Issue Date:
Expiration Date:
Director May 24, 2027 June 21, 2024
PERRYJOHNSONLABORATORY ACCREDITATION,INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) 4541 South 700 East, Suite #250, Salt Lake City, UT 84107
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system
Inspection Body Type A
(As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Initial Accreditation Date: Issue Date: Expiration Date: November 22, 2022 November 22, 2022 December 31, 2024
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
4541 South 700 East, Suite #250, Salt Lake City, UT 84107
Contact Name: Mohamed Kalif Phone: 385-232-2343
Accreditation is granted to the facility to perform the following inspections:
Inspection Category A
FIELD OF INSPECTION
Non-Destructive
Pressure Equipment
Design Verification, New Construction Verification, and In-service Inspection
TYPES OR RANGES OF INSPECTIONS
Welding Joints, Piping, Vessels and Storage Tanks Ultrasonic Test (UT)
Container Inspection
Pressure Equipment Design Verification , New Construction Verification, and In-service Inspection
Piping & Pipeline Inspection
Design Verification, New Construction Verification, and In-service Inspection
Design Verification, New Construction Verification, and In-service Inspection Above Ground Storage Tanks
Offshore Container Freight Container
SPECIFICATION, STANDARD METHOD, OR TECHNIQUE USED
STM E-317, ASTM E-494, ASTM E-1324, ASTM E-2375 MIL-STD 2154, ASME Section V Articles 4 and 5; ASME Sections I, VIII, IX, B31.1,B31.3; AWS D1.1, D1.5, API 1104, 650, ASTM A388, E164, A609, E797
Shipment Inspection Pre-Shipment Inspection
1. Inspection Body Classifications (Type A, B or C)
API Standard 510 ASME Boiler & Pressure Vessel Code Sections I through XII, ASME B31 Code for Pressure Piping, ASME PVHO, ASME FFS, ASME QAI-1, National Board Inspection Code (NBIC), NB-360 and NB-369.
API Standard 570 API Standard 1104
API Standard 653
EN 12079:2006
DNV 2.7-1:2021
DNV2.7-2:2016
International Convention for the Safety of Life at Sea (SOLAS), 1974 Convention for Safe Containers (CSC), 1972
MIL-STD-105E
ISO 2859-1:1999
i. Type A- An inspection body providing third party inspections
Project management Institue (PMI)
Lifting Equipment Engineers Association (LEEA)
Dun & Bradstreet (DUNS)
International Association of Drilling Contractors (IADC)
American Society for Quality (ASQ)
Chartered Institute of Environmental Health (CIEH) accounted training provider
American Society for Nondestructive Testing (ASNT)
TNV System Certification (ISO Certification Body)
21September,2020
DearMr.Majlesein,
ThankyouforwritingtotheSecretary-Generaltoexpressyourcompany’scommitmenttothe GlobalCompact’sprinciplesintheareasofhumanrights,labour,environmentandanti-corruption.We applaud your leadership in making this decision and welcome your company’s participation in the Global Compact – the world’s largest corporate citizenship initiative, with thousands of business participants and other stakeholders from civil society, labour and government based in over 160 countries.
The Global Compact asks participating companies to pursue two complementary goals: (1) internalizethetenprincipleswithinthecompany’sstrategies,policiesandoperationsand(2)undertake projectstoadvancethebroaderdevelopmentgoalsoftheUnitedNations,particularlytheSustainable DevelopmentGoals.Weunderstandthatimplementationofuniversalprinciplesintobusinessisalongterm process, and encourage participants to follow a path of continuous improvement. This commitmentrequiresthesustainedsupportofleadershipthroughongoingactivitiesandpartnerships, as well as a company’s engagement in dialogues, willingness to learn and dedication to practical actions.
Asavoluntaryinitiative,theGlobalCompactdrawsstrengthfromourparticipants’commitment and actions. To spur implementation and progress, we provide various learning and engagement opportunitiesforourparticipants.Theseinclude:80-pluscountryandregionalnetworkswhereissues andactivitiesaredrivenatalocallevel;practicaltoolsandguidancedocumentsontheprinciplesand other priority issues; and international and local events where multi-stakeholder participants can exchange experiences, partake in learning and problem- solving exercises, engage in dialogue and identifylike-mindedorganizationsforpartneringprojects.
Further details on such activities can be found in the attached guidance document, “After the Signature:AGuidetoEngagementintheUnitedNationsGlobalCompact”andontheGlobalCompact website(www.unglobalcompact.org).
Mr.ShahriyarMajlesein CEO
CitadelEngineeringCompany
Erbil
Credibilityandaccountabilityarecriticalfactorsforadvancingtheresponsiblebusinessagenda – and for protecting the legitimacy of the Global Compact. Therefore, a key requirement for participation in the initiative is the annual submission of a Communication on Progress (COP) that describes your company’s efforts to implement the ten principles. Your company’s first COP is due within one year of joining the Global Compact, and every year thereafter. We take this integrity measureseriouslyandcompaniesthatfailtomeetconsecutiveCOPdeadlineswillbedeactivated.
The Communication on Progress serves as far more than an indication of engagement in the Global Compact, and I encourage you to regard the process as a mechanism for assessing and demonstratingtheimpactofyourcompany’sactionstoincorporateresponsiblepracticesintoday-today operations and to bring about meaningful change in society. Guidelines for preparing and submittingyourcompany’sCOParealsoavailableintheattachedguidancedocument.
Again, we thank you for joining the Global Compact. We are eager to hear your ideas and experiences,andencourageyoutoshareyourviewswithus.Westandreadytosupportyoureffortsto embrace the ten universal principles and contribute to a more sustainable and inclusive global economy.
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC) No. 201, Italian Village, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
Flow Meter Calibration
(As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA) 755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±) CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Mass Flow Rate (Petroleum)FO 163 000 kg/h to 272 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 3" (in) API MPMS 4.5-2016
MPMS 4.8-2013 415 179 kg/h to 545 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 4" (in)
API MPMS 4.5-2016
MPMS 4.8-2013
904 211 kg/h to 1 470 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 8" (in) API MPMS 4.5-2016
Volumetric Flow Rate (Petroleum)FO
L/min to 113.6 L/min ± 0.014 % of
Flow Meter 1/2" (in) API MPMS 4.5-2016 API MPMS 4.8-2013
870.6 L/min to 1 317 L/min ± 0.014 % of reading Coriolis Flow Meter 2" (in)
API MPMS 4.5-2016 API MPMS 4.8-2013
Prover Base Volume (Pipe prove, Compact Prover, Tank Prover)FO
2 729 L/min to 4 542 L/min ± 0.014 % of reading
6 916 L/min to 9 085 L/min ± 0.014 % of reading
6 916 L/min to 9 085 L/min ± 0.014 % of reading
15 085 t/min to 24 378 L/min ± 0.014 % of reading
30 Gal 200 Gal 300 Gal ± 0.017 % of reading ± 0.019 % ± 0.019 %
Coriolis Flow Meter 3" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 4" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 6" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 8" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Water Draw Package
API MPMS 12.2.4 / 4.9.2
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE RANGE
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED Liquid
Fixed Storage Tanks - Road Tankers
Volumetric method using flow meter
Calibration according to: ISO 4269:2001 (Incremental method using volumetric meters) OIML R 63:1994 “Petroleum measurement tables” OIML R 80-1:2009 “Road and rail tankers with level gauging. Part 1: Metrological and technical requirements” Calibration medium: Liquid hydrocarbons (gasoline, diesel oil, biodiesel, JET A1)
Calibration performed on site
Geometric method using strapping tape
Calibration according to: ISO 7507-1:2003 (Strapping Method) Calibration performed on site
Cylindrical Tanks
Geometric method using total station
Calibration according to: ISO 7507-3:2006 (Optical triangulation method with reference circumference) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site Liquid
Geometric method using total station
Calibration according to: ISO 7507-4:2010 (Internal electro-optical distance ranging method) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site
Geometric method using strapping tape
Calibration according to: ISO 129171:2002 (External strapping method) ISO 7507-1:2003 (Remaining measurements) Calibration performed on site
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Accreditation is granted to the facility to perform the following calibrations:
1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree.
2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity.
3. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations. Example: Outside MicrometerFO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations.
4. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location.
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC)
No. 201, Italian Village, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system.
Inspection Body (Category-A) (As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Accreditation is granted to the facility to perform the following inspections:
Category A
FIELD OF INSPECTION
Non-Destructive Testing
TYPES OR RANGES OF INSPECTIONS
SPECIFICATION, STANDARD METHOD, OR TECHNIQUE USED
Magnetic Particle Test (MT) ASTM E-1444, MIL-STD-1949, ASTM E-709, MIL-I-6868
1) Inspection Body Classifications (Type A, B or C)
Type A- An inspection body providing third party inspections
Type B- An inspection body providing first party inspections, second party inspections, or both, which forms a separate and identifiable part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services only to its parent organization (in-house inspection body)
Type C- An inspection body providing first party inspections, second party inspections, or both, which forms an identifiable but not necessarily a separate part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services to its parent organization or to other parties, or to both
Ministry of Oil No. f7/A/157/3525
Technical department Date: 06.05.2021
Telegraph
Allofouroilcompaniesexceptoilprojects,oilexploration,Iraqidrilling,oilmarketing, and heavy engineering equipment.
Meter calibration services and calibration equipment And issuance of certificates of accreditation and calibration
Referring to the Ministerial Order (10645) on 05.04.2021, which included sending your staff to meet the invitation of ( CITADEL ENGINEERING COMPANY ) for the purposeofaccreditingits laboratoryforcalibrationofcalibrationequipment. The above company’s headquarters were visited on 08.04.2021, and its services in the calibration field were viewed, we would like to show the following:-
1- Our companies must define and study the field in which the company is globally approved (specifications and the extent to which it is used in relation to the equipment available on its site in addition to the methods by which the calibration is carried out and in the event of changing the methods, it must be re-confirmed and approved.
2- The ability of our companies to benefit from the above laboratory in calibrating the equipment according to the tasks and duties accompanying their international certification of approval directly in accordance with the paragraph (4) of the approved meeting minutes by the Minister and attached to our memorandum No. 1658 on 01.03.2020, Included (each oil company as self-financing companies) are responsible for their contracts under Law (22) for 1997 , because the law granted independence and administration with its legal personality, includes its independence by contracting in accordance with Article 19 of the aforementioned law
With best regards
Attachments
The duties & tasks of the company above.
Ali Warid Hamoud General Director
06-05-2021
Mansour Abdulmajed Jalil
Copy to : -CITADEL ENGINEERING COMPANY- info@citadel-engineering.co, for your information and to coordinate with the oil companies authorized to sign with you according to mentioned above
PERRYJOHNSONLABORATORY ACCREDITATION,INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
Chemical, Electrical, Mechanical, Thermodynamic, Time and Frequency, and Flow Meter Calibration (As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
Initial Accreditation Date: Issue Date: Expiration Date: October 20, 2020 March 3, 2023 April 30. 2025
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Chemical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE CALIBRATION AND MEASUREMENT
pH MeterF 4.01 pH
pH
pH
Conductivity MeterF 1.33 µS/cm
903 µS/cm
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
pH at 25ºC
µS/cm
Density MeterF 0.99 910 g/mL at 15 °C 0.01 % of reading
0.99 702 g/mL at 25 °C
Turbidity MeterF 0.5 NTU
Equipment to Measure Min
Reid Vapor Pressure
Equipment to Measure Sulfur Content X-RayF
Colour MeterF
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Buffer Solution / CEC-CAD-PRD-EN-0061
Conductivity Standards / CEC-CAD-PRD-EN-0059
Density Reference Standard / CEC-CAD-PRD-EN-0052 0.99 821 g/mL at 20 °C
NTU
NTU 8 NTU
NTU 2 NTU 400 NTU 8 NTU
000 NTU
Close Cap Flash Point MeterF 64 ºC
Smoking Point MeterF
Pour Point MeterF
HydrometersF 0.5 to 1
Shelling (Density of Gas)F 1.256 g/L
Gas – ChromatographyF C1 – C6
Accreditation is granted to the facility to perform the following calibrations: Issue: 3/2023
Using Formazin Turbidity Standards
Water Mark Karl Fischer Water Standard / ASTM E203-16
Vapor Pressure Standard / ASTMP-124-03-VAP & ASTM D323
Sulfur Reference Standard /ASTM D4294
Colour Ref Standard / ASTM D 6045 and D1500 Open Cap Flash Point MeterF 84 ºC
Flash Point Reference Standard Field Metrology Well 9142 / ASTM-D-92
Flash Point Reference Standard Field Metrology Well 9142 / ASTM-D-93
Smoking Point Reference Standard / ASTM-D-1322
Pour Point Reference Standard/ ASTM-D-97
DAW-ACETONE-TOLUENE / ASTM-368
Pure Nitrogen / IP-59
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Chemical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
MeterF
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Equipment To Output DC VoltageFO
Equipment To Output AC Voltage
the Listed FrequenciesFO
Equipment To Output AC Voltage At the Listed FrequenciesFO
Equipment To Output AC Voltage At the Listed FrequenciesFO
3
50 kHz to 100 kHz
100 kHz to 300 kHz
Issue: 3/2023
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Viscosity Reference Standard and ASTM D445,D446,D2171, CECCAD-PRD-EN-0062
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Fluke 8846A / OEM Manual, EUROMET cg-15
Page 3 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE RANGE OR NOMINAL DEVICE
Equipment To Output AC Voltage At the Listed FrequenciesFO
3
5
Fluke 8846A / OEM Manual, EUROMET cg-15
Equipment To Output AC Voltage
At the Listed FrequenciesFO 3
Equipment To Output AC Voltage
At the Listed FrequenciesFO
3
100 kHz to 300 kHz
Equipment To Output AC Voltage
At the Listed FrequenciesFO
Issue: 3/2023
Page 4 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Equipment To Measure Output ResistanceFO up to 10 Ω 0.12 mΩ/Ω + 3 mΩ Fluke 8846A / OEM Manual, EUROMET cg-15
10 Ω to 100 Ω 0.12 mΩ/Ω + 4 mΩ
100 Ω to 1 kΩ 0.12 mΩ/Ω + 10 mΩ
1 kΩ to 10 kΩ 0.12 mΩ/Ω + 100 mΩ
10 kΩ to 100 kΩ 0.12 mΩ/Ω + 1 Ω
100 kΩ to 1 MΩ 0.12 mΩ/Ω + 10 Ω
1 MΩ to 10 MΩ 0.46 mΩ/Ω + 100 Ω
1 MΩ to 10 MΩ 0.46 mΩ/Ω + 100 Ω
10 MΩ to 100 MΩ 9 mΩ/Ω + 10 kΩ
100 MΩ to 1 GΩ 23 mΩ/Ω + 100 kΩ
Equipment To Measure Output DC CurrentFO
5 µA to 100 µA 0.6 mA/A + 25 nA
100 µA to 1 mA
0.6 mA/A + 50 nA
1 mA to 10 mA 0.6 mA/A + 2 µA
10 mA to 100 mA 0.6 mA/A + 5 µA
100 mA to 1 A 0.6 mA/A + 0.2 mA
1 A to 3 A 1.2 mA/A + 0.6 mA
3 A to 10 A 1.7 mA/A + 0.8 mA
10 A to 40 A 2.3 % of reading + 50 mA
40 A to 400 A 2.3 % of reading + 0.5 A
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz 5 µA to 100 µA 1.2 % of reading + 40 nA
5 Hz to 10 Hz 5 µA to 100 µA 0.4 % of reading + 40 nA
10 Hz to 5 kHz 5 µA to 100 µA 0.1 % of reading + 40 nA
5 kHz to 10 kHz
5 µA to 100 µA 0.2 % of reading + 250 nA
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz
5 Hz to 10 Hz
5 Hz to 10 Hz
10 Hz to 5 kHz
5 kHz to 10 kHz
100 µA to 1 mA 1.2 % of reading + 0.4 µA
100 µA to 1 mA 0.4 % of reading + 0.4 µA
100 µA to 1 mA 0.4 % of reading + 0.4 µA
100 µA to 1 mA 0.1 % of reading + 0.4 µA
100 µA to 1 mA 0.2 % of reading + 2.5 µA
Fluke 325 / OEM Manual, EUROMET cg-15
Fluke 8846A / OEM Manual, EUROMET cg-15
Issue: 3/2023 This supplement is in conjunction with certificate #L23-199 Page 5 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Equipment To Output AC Current At the Listed FrequenciesFO
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
3 Hz to 5 Hz 1 mA to 10 mA 1.2 % of reading + 4 µA
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz 10 mA to 100 mA
5
to
10 Hz to 5 kHz 10 mA to 100 mA 0.1 % of reading + 40 µA
5 kHz to 10 kHz 10 mA to 100 mA 0.2 % of reading + 250 µA
Equipment To Output AC Current At the Listed FrequenciesFO
3 Hz to 5 Hz 100 mA to 1 A 1.2 % of reading + 0.4 mA
5 Hz to 10 Hz
mA to 1 A 0.4 % of
+ 0.4 mA 10 Hz to 5 kHz
5 kHz to 10 kHz
Equipment To Output AC Current At the Listed FrequenciesFO
mA to 1 A
mA to 1 A
% of reading + 7 mA
3 Hz to 5 Hz 1 A to 3 A 3 Hz to 5 Hz
5 Hz to 10 Hz 1 A to 3 A 5 Hz to 10 Hz
10 Hz to 5 kHz 1 A to 3 A 10 Hz to 5 kHz
5 kHz to 10 kHz 1 A to 3 A 5 kHz to 10 kHz
Equipment To Output AC Current
At the Listed FrequenciesFO
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Fluke 8846A / OEM Manual, EUROMET cg-15
3 Hz to 5 Hz 3 A to 10 A 2.3 % of reading + 6 mA
5 Hz to 10 Hz 3 A to 10 A 1.3 % of reading + 6 mA
10 Hz to 5 kHz 3 A to 10 A 0.2 % of reading + 6 mA
5 kHz to 10 kHz 3 A to 10 A 0.4 % of reading + 70 mA
5 kHz to 10 kHz 3 A to 10 A 0.4 % of reading + 70 mA
Issue: 3/2023
Page 6 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
NOMINAL
Equipment To Output AC Current At the Listed FrequenciesFO Fluke 325 / OEM Manual, EUROMET cg-15
40 Hz to 65 Hz
Equipment To Output AC Current At the Listed FrequenciesFO
Capacitor and Equipment to Measure Output
CapacitanceFO
of
+
pF
nF to 100 nF
% of reading + 500 pF 100 nF to 1µF
µF to 10 µF
% of reading + 5 nF
% of reading + 50 nF
µF to 100 µF 1.2 % of reading + 500 nF 100 µF to 1 mF 1.2 % of reading + 5 µF 1 mF to 10 mF 1.2 % of reading + 50 µF 10 mF to 100 mF 4.6 % of reading + 200 µF
Equipment to Measure DC VoltageFO Up to 329.999 mV 0.11 mV/V
µV
10 V to 329.999 V 0.1 mV/V + 1.5 mV
100 V to 1 020 V 0.1 mV/V + 5.5 mV
Equipment to Measure DC CurrentFO Up to 329.99 µA 0.7 mA/A + 0.1 µA 0.33 mA to 3.29 mA 0.6 mA/A + 0.25 µA
3 3 mA to 32.9 mA
mA/A + 1.25 µA 33 mA to 329.99 mA 0.48 mA/A + 16.5 µA
0.33 A to 1.099 9 A 1.4 mA/A + 220 µA 1.1 A to 2.999 9 A 1.8 mA/A + 220 µA
3 A to 10.999 A 2.3 mA/A + 2.5 mA 11 A to 20.500 A 4.8 mA/A + 3.75 mA
55 A to 150 A 0.36 % of reading + 11 mA
/ OEM Manual, EUROMET cg-15
16 A to 55 A 0.34 % of reading + 11 mA Fluke 5080A Via 50-Turn Current Coil / OEM Manual, EUROMET cg-15
150 A to 550 A 0.41 % of reading + 125 mA
550 A to 1 025 A 0.65 % of reading + 188 mA
Issue: 3/2023 This supplement is in conjunction with certificate #L23-199 Page 7 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Equipment to Measure Resistance, Fixed Points
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Fluke 5080A / OEM Manual, EUROMET cg-15
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Equipment To Measure AC Voltage
At The Listed Frequencies
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Issue: 3/2023
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Fluke 5080A / OEM Manual, EUROMET cg-15 45
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Equipment To Measure AC Voltage
At The Listed FrequenciesFO
Equipment To Measure AC Current
At The Listed FrequenciesFO
Equipment To Measure AC
Equipment To Measure AC Current At
Equipment To Measure AC Current At The Listed FrequenciesFO 45
Equipment To Measure
Equipment To Measure AC Current
At The Listed FrequenciesFO
45 Hz to 65 Hz 1.1 A to 2.999 9 A
Issue: 3/2023
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Electrical
Equipment To Measure AC Current At The Listed FrequenciesFO
45
Equipment To Measure AC Current At The Listed FrequenciesFO
Equipment To Measure AC Current
At The Listed FrequenciesFO
Equipment To Measure
Fluke 5080A / OEM Manual, EUROMET cg-15
Equipment To Measure AC Current At The Listed Frequencies
Issue: 3/2023
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Mechanical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
Mass Flow Meter (Water)FO 3 614 kg/h to 6 820 kg/h
3/2023
163 000 kg/h to 272 000 kg/h
415 179 kg/h to 545 000 kg/h
415 179 kg/h to 545 000 kg/h
904 211 kg/h to 1 470 000 kg/h
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Coriolis Flow Meter1/2" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 2" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 3" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 4" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 6" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 8" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Mechanical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED Volumetric Flow
Accreditation is granted to the facility to perform the following calibrations: Issue: 3/2023
Coriolis Flow Meter 1/2" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 2" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 3" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 4" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 6" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter 8" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter Comparison Oil & Water Density within DPT
Density Calibration Stand
Flow Meter 1/2" (in) API MPMS 4.5-2016 API MPMS 4.8-2013
Coriolis Flow Meter 2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 3" (in) API MPMS 4.5-2016
4.8-2013
Coriolis Flow Meter 4" (in)
API MPMS 4 5-2016
API MPMS 4.8-2013
904
Coriolis Flow Meter 8" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Volumetric Flow Rate (Petroleum)FO 60.57 L/min to 113.6 L/min 0.056 % of reading
870.6 L/min to 1 317 L/min
2 729 L/min to 4 542 L/min
6 916 L/min to 9 085 L/min
6 916 L/min to 9 085 L/min
15 085 L/min to 24 378 L/min
Prover Base Volume (Pipe prove, Compact Prover, Tank Prover)FO
Calibration according to: ISO 4269:2001 (Incremental method using volumetric meters) OIML R 63:1994 “Petroleum measurement tables” OIML R 80-1:2009 “Road and rail tankers with level gauging. Part 1: Metrological and technical requirements”
Calibration medium: Liquid hydrocarbons (gasoline, diesel oil, biodiesel, JET A1) Calibration performed on site
Issue: 3/2023 This supplement is in conjunction with certificate #L23-199 Page 13 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein
Phone: +1(801) 326-4626
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Vertical Cylindrical TanksFO
50 m3
200
2
% of reading
Torque Wrenches /Torque DriversF
500 m3 0.13 % of reading
2 000 m3 0.09 % of reading
10 000 m3 0.07 % of reading
20 000 m3 0.06 % of reading
75 000 m3 0.06 % of reading
120 000 m3 0.06 % of reading
200 m3 0.16 % of reading
2 000 m3 0.13 % of reading
10 000 m3 0.09 % of reading
40 000 m3 0.06 % of reading
75 000 m3 0.06 % of reading
120 000 m3 0.06 % of reading
(Above 200 m3 Min tank diameter: 5m) of nominal tank volume
5 nm to 500 nm 1 % of reading
Liquid Volume/Horizontal Cylindrical TanksFO
Accreditation is granted to the facility to perform the following calibrations: Issue: 3/2023
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Geometric method using strapping tape
Calibration according to: ISO 7507-1:2003 (Strapping Method)
Calibration performed on site
500 nm to 1 000 nm 1 % of reading
1 000 nm to 2 000 nm 1 % of reading
Up to 400 m3 Maximum tank diameter: 4m Maximum tank length: 30m
0.065 % of nominal tank volume
Geometric method using total station
Calibration according to: ISO 7507-3:2006 (Optical triangulation method with reference circumference) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site
Geometric method using total station
Calibration according to: ISO 7507-4:2010 (Internal electrooptical distance ranging method) ISO 7507-1:2003 (Remaining measurements)
Temperature Sensors And Temperature Measuring InstrumentsFO
Thermo Hygrometer at
To
Time and Frequency MEASURED INSTRUMENT, QUANTITY OR GAUGE
TachometerFO
Equipment To
Output FrequencyFO
Fluke 9132 / OIML R 147 / ASTM E2847
PRT and TC Sensors / EURAMET cg-20 / EN 60068-3-5
PRT And TC Sensors Via Fluke 8846A / ASTM E2488-9
FLUKE 9142, 9144, Semi Standard PRT, Fluke 8846A / ASTM-E2877, EA 10/11, OIML R84
Stability Test Chamber ZF120 / ASTM E126
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Lutron DT-2269 / OEM Manual, EUROMET cg-15
Fluke 8846A / OEM Manual, EUROMET cg-15
% of reading
1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree
Issue: 3/2023 This
Page 16 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity.
3. The presence of a superscript F means that the laboratory performs calibration of the indicated parameter at its fixed location Example: Outside MicrometerF would mean that the laboratory performs this calibration at its fixed location.
4. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations Example: Outside MicrometerFO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations.
5. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location.
Issue: 3/2023
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
Flow Meter Calibration
(As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA) 755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Fixed Storage Tanks - Road Tankers
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
0.5 m3 to 10 m3
CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
0.13% of nominal tank volume
(50 m3 to 10000 m3. Max tank diameter: 32m)
0.17 % of reading 0.12 % of reading 0.12 % of reading 0.11% of reading of nominal tank volume
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Volumetric method using flow meter
Calibration according to: ISO 4269:2001 (Incremental method using volumetric meters) OIML R 63:1994 “Petroleum measurement tables” OIML R 80-1:2009 “Road and rail tankers with level gauging. Part 1: Metrological and technical requirements” Calibration medium: Liquid hydrocarbons (gasoline, diesel oil, biodiesel, JET A1)
Calibration performed on site
Geometric method using strapping tape
Calibration according to: ISO 7507-1:2003 (Strapping Method) Calibration performed on site Liquid
0.19 % of reading
0.13 % of reading
0.09 % of reading
0.07 % of reading
0.06 % of reading
0.06 % of reading
(Above 250 m3. Min tank diameter: 8m)
0.06 % of reading of nominal tank volume
Geometric method using total station
Calibration according to: ISO 7507-3:2006 (Optical triangulation method with reference circumference) ISO 7507-1:2003 (Remaining measurements)
Accreditation is granted to the facility to perform the following calibrations:
Mechanical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Vertical Cylindrical Tanks
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
200 m3
2 000 m3
10 000 m3
40 000 m3
75 000 m3
130 000 m3
(Above 200 m3 Min tank diameter: 5m)
Liquid Volume/Horizontal Cylindrical Tanks
Up to 400 m3 Maximum tank diameter: 4m Maximum tank length: 30m
CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
0.16 % of reading
0.09 % of reading
0.07 % of reading
0.06 % of reading
0.06 % of reading
0.06 % of reading of nominal tank volume
0.065% of nominal tank volume
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Geometric method using total station
Calibration according to: ISO 7507-4:2010 (Internal electrooptical distance ranging method) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site
Geometric method using strapping tape
Calibration according to: ISO 12917-1:2002 (External strapping method) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site
1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree.
2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity.
3. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations. Example: Outside MicrometerFO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations.
4. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location.
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) 136 East South Temple, Suite 1400, Salt Lake City, UT 84111
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system.
Inspection Body (Category-A)
(As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system.
Inspection Body (Category-A) (As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Accreditation is granted to the facility to perform the following inspections:
FIELD OF INSPECTION
Pipelines
TYPES OR RANGES OF INSPECTIONS
Piping
VT Set/NDT Set
1) Inspection Body Classifications (Type A, B or C)
SPECIFICATION, STANDARD METHOD, OR TECHNIQUE USED
ASME B31.3
Type A- An inspection body providing third party inspections
Type B- An inspection body providing first party inspections, second party inspections, or both, which forms a separate and identifiable part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services only to its parent organization (in-house inspection body)
Type C- An inspection body providing first party inspections, second party inspections, or both, which forms an identifiable but not necessarily a separate part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services to its parent organization or to other parties, or to both
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) 10 W Broadway, Suite 700, Salt Lake City, UT 84101
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system
Inspection Body Type A
(As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
Initial Accreditation Date: Issue Date: Expiration Date: November 22, 2022 November 22, 2022 December 31, 2024
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
10 W Broadway, Suite 700, Salt Lake City, UT 84101
Contact Name: Mr. Shahriyar Majlesein Phone: 1801-326-4626
Accreditation is granted to the facility to perform the following inspections:
Inspection Category A
FIELD OF INSPECTION
Non-Destructive
Pressure Equipment
Design Verification, New Construction Verification, and In-service Inspection
TYPES OR RANGES OF INSPECTIONS
Welding Joints, Piping, Vessels and Storage Tanks Ultrasonic Test (UT)
Pressure Equipment Design Verification , New Construction Verification, and In-service Inspection
Piping & Pipeline Inspection
Design Verification, New Construction Verification, and In-service Inspection
Design Verification, New Construction Verification, and In-service Inspection Above Ground Storage Tanks
1. Inspection Body Classifications (Type A, B or C)
SPECIFICATION, STANDARD METHOD, OR TECHNIQUE USED
ASTM E-317, ASTM E-494, ASTM E-1324, ASTM E-2375 MIL-STD 2154, ASME Section V Articles 4 and 5; ASME Sections I, VIII, IX, B31.1,B31.3; AWS D1.1, D1.5, API 1104, 650, ASTM A388, E164, A609, E797
API Standard 510 ASME Boiler & Pressure Vessel Code Sections I through XII, ASME B31 Code for Pressure Piping, ASME PVHO, ASME FFS, ASME QAI-1, National Board Inspection Code (NBIC), NB-360 and NB-369.
API Standard 570 API Standard 1104
API Standard 653
i. Type A- An inspection body providing third party inspections
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
For PJLA:
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
FLOW METER CALIBRATION
(As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules. Initial Accreditation Date: Issue Date: Expiration Date: October20,2020 October20,2020 January31,2023
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Mass Flow Meter (Water)FO
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
3 614 kg/h to 6 820 kg/h ± 0.014 % of reading
52 160 kg/h to 87 100 kg/h ± 0.014 % of reading
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Coriolis Flow Meter
1/2" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter
2" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52 IS0 4185:1980
163 000 kg/h to 272 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 3" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
415 179 kg/h to 545 000 kg/h ± 0.014 % of reading
Coriolis Flow Meter 4" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52 IS0 4185:1980
415 179 kg/h to 545 000 kg/h ± 0.014 % of reading
904 211 kg/h to 1 470 000 kg/h ± 0.014 % of reading
Coriolis Flow Meter 6" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 8" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Volumetric Flow Rate (Water)FO
Density (Liquid)FO
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
Mass Flow Rate (Petroleum)FO
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
60.57 L/min to 113.6 L/min ± 0.014 % of reading Coriolis Flow Meter
1/2" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
870.6 L/min to 1 317 L/min ± 0.014 % of reading Coriolis Flow Meter
2" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
2 729 L/min to 4 542 L/min ± 0.014 % of reading Coriolis Flow Meter
3" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
6 916 L/min to 9 085 Lit/min ± 0.014 % of reading Coriolis Flow Meter
6 916 L/min to 9 085 Lit/min ± 0.014 % of reading
15 085 L/min to 24 378 Lit/min ± 0.014 % of reading
4" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter
6" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter
8" (in)
995.0 kg/m3 to 999.7 kg/m3 ± 0.005 + 0.014 % of reading
772.4 kg/m3 to 798.8 kg/m3 ± 0.005 + 0.014 % of reading
3 614 kg/h to 6 820 kg/h ± 0.014 % of reading
52 160 kg/h to 87 100 kg/h ± 0.014 % of reading
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter
Comparison
Oil & Water Density
within DPT Density
Calibration Stand
Coriolis Flow Meter
1/2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter
2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
EQUIPMENT AND REFERENCE STANDARDS USED Mass Flow Rate (Petroleum)FO 163 000 kg/h to 272 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 3" (in) API MPMS 4.5-2016
415 179 kg/h to 545 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 4" (in) API MPMS 4.5-2016
MPMS 4.8-2013
904 211 kg/h to 1 470 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 8" (in)
Volumetric Flow Rate (Petroleum)FO 60.57 L/min to 113.6 L/min ± 0.014 % of
MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 1/2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Prover Base Volume (Pipe prove, Compact Prover, Tank Prover)FO
870.6 L/min to 1 317 L/min ± 0.014 % of reading
2 729 L/min to 4 542 L/min ± 0.014 % of reading
Coriolis Flow Meter 2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 3" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
6 916 L/min to 9 085 L/min ± 0.014 % of reading Coriolis Flow Meter 4" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
6 916 L/min to 9 085 L/min ± 0.014 % of reading Coriolis Flow Meter 6" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
15 085 t/min to 24 378 L/min ± 0.014 % of reading Coriolis Flow Meter 8" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
30 Gal
Gal
Gal ± 0.017 % of reading ± 0.019 % ± 0.019 %
Water Draw Package
MPMS 12.2.4 / 4.9.2
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Fixed Storage Tanks - Road Tankers
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Volumetric method using flow meter
Calibration according to: ISO 4269:2001 (Incremental method using volumetric meters) OIML R 63:1994 “Petroleum measurement tables” OIML R 80-1:2009 “Road and rail tankers with level gauging. Part 1: Metrological and technical requirements” Calibration medium: Liquid hydrocarbons (gasoline, diesel oil, biodiesel, JET A1)
Calibration performed on site
Geometric method using strapping tape
Calibration according to: ISO 7507-1:2003 (Strapping Method) Calibration performed on site
Geometric method using total station
Calibration according to: ISO 7507-3:2006 (Optical triangulation method with reference circumference) ISO 7507-1:2003 (Remaining measurements) Calibration performed on site
Geometric method using total station
Calibration according to: ISO 7507-4:2010 (Internal electro-optical distance ranging method) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site Liquid Volume/ -
Geometric method using strapping tape
Calibration according to: ISO 129171:2002 (External strapping method) ISO 7507-1:2003 (Remaining measurements) Calibration performed on site
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree.
2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity.
3. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations. Example: Outside MicrometerFO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations.
4. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location.
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
For PJLA:
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
FLOW METER CALIBRATION
(As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules. Initial Accreditation Date: Issue Date: Expiration Date: October20,2020 October20,2020 January31,2023
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) 136 East South Temple, Suite 1400, Salt Lake City, UT 84111
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system.
Inspection Body (Category-A)
(As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
C E R T I F I CAT E
ISO 9001 : 2015
The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH
AbuDhabi
Operates a management system in accordance with the requirements of ISO 9001 : 2015 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
Management system as per C E R T I F I CAT E
ISO 14001 : 2015
The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH AbuDhabi
Operates a management system in accordance with the requirements of ISO 14001 : 2015 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
C
E R T I F I CAT E
Management system as per
ISO 45001 : 2018
The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH AbuDhabi
operates a management system in accordance with the requirements of ISO 45001 : 2018 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
Is an Executive Member of the International Lifting Equipment Engineers Bureau. The organisation has been audited in accordance with ILEEB's approved code of practice on the following sections :
Membership Number. : IL-1856
Issue Date : 04/07/2022
Expiry Date : 03/07/2023
validate@ileeb.com
Bowan Technical Director
-
Justin
ANNUAL MEMBERSHIP CERTIFICATE 2021
We
This certifies all requirements for the designation as an OSHAcademy
Authorized Training Provider has been met
by
Citadel Engineering Company
This organization has met all qualifications and is designated as an OSHAcademy Authorized Training Provider (ATP). They may perform all activities necessary, as defined by the Authorized Training Provider Manual, to conduct OSHAcademy training during the registration period and in the geographical region(s) specified below:
Steven J. Geigle, M.A., CET, CSHM Director
OSHAcademy Safety & Health Training
OSHAcademy training conforms to OSHA Training Standards and ANSI Z490.1-2009, Criteria for Accepted Practices in Safety, Health and Environmental Training. OSHAcademy training is recognized by the National Safety Management Society (NSMS) and the Institute for Safety and Health Training (ISHM).
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system.
Inspection Body (Category-A) (As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Accreditation is granted to the facility to perform the following inspections:
FIELD OF INSPECTION
Pipelines
TYPES OR RANGES OF INSPECTIONS
Piping
VT Set/NDT Set
1) Inspection Body Classifications (Type A, B or C)
SPECIFICATION, STANDARD METHOD, OR TECHNIQUE USED
ASME B31.3
Type A- An inspection body providing third party inspections
Type B- An inspection body providing first party inspections, second party inspections, or both, which forms a separate and identifiable part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services only to its parent organization (in-house inspection body)
Type C- An inspection body providing first party inspections, second party inspections, or both, which forms an identifiable but not necessarily a separate part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services to its parent organization or to other parties, or to both
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) 136 East South Temple, Suite 1400, Salt Lake City, UT 84111
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system.
Inspection Body (Category-A)
(As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
May 17, 2022
Mr. Shahriyar Majlesein
Citadel Engineering Company (CEC)
Gazna Road
Erbil Kurdinstan Regio
Dear Mr. Shahriyar Majlesein:
Congratulations! This letter is to inform you that your scope expansion assessment to ISO/IEC 17025: 2017 for Temperature, Humidity, Electrical, Pressure, Tachometer, and Chemical Calibration, with PJLA assessor Mr. Felipe Narcio was completed May 13, 2022. Upon finalization of all information Mr. Felipe Narcio will complete the accreditation process by recommending you for final accreditation.
Our Executive Committee, will then review the assessment material. Upon their agreement with Mr Narcio’s recommendation, your final accreditation will be granted. A draft certificate will then be prepared for your review and approval.
On behalf of the PJLA staff, I would like to commend you on your superior management system and demonstrated commitment to quality. If we can be of any further assistance to you, please feel free to contact me directly. Thank you for selecting Perry Johnson Laboratory Accreditation, Inc.
Cordially,
Tracy Szerszen President
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
For PJLA:
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
FLOW METER CALIBRATION
(As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules. Initial Accreditation Date: Issue Date: Expiration Date: October20,2020 October20,2020 January31,2023
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Mass Flow Meter (Water)FO
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
3 614 kg/h to 6 820 kg/h ± 0.014 % of reading
52 160 kg/h to 87 100 kg/h ± 0.014 % of reading
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Coriolis Flow Meter
1/2" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter
2" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52 IS0 4185:1980
163 000 kg/h to 272 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 3" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
415 179 kg/h to 545 000 kg/h ± 0.014 % of reading
Coriolis Flow Meter 4" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52 IS0 4185:1980
415 179 kg/h to 545 000 kg/h ± 0.014 % of reading
904 211 kg/h to 1 470 000 kg/h ± 0.014 % of reading
Coriolis Flow Meter 6" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Coriolis Flow Meter 8" (in)
Transfer Standard | Dynamic Collection Method
CEC-SOP-FC-52
IS0 4185:1980
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Volumetric Flow Rate (Water)FO
Density (Liquid)FO
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
Mass Flow Rate (Petroleum)FO
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
60.57 L/min to 113.6 L/min ± 0.014 % of reading Coriolis Flow Meter
1/2" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
870.6 L/min to 1 317 L/min ± 0.014 % of reading Coriolis Flow Meter
2" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
2 729 L/min to 4 542 L/min ± 0.014 % of reading Coriolis Flow Meter
3" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
6 916 L/min to 9 085 Lit/min ± 0.014 % of reading Coriolis Flow Meter
6 916 L/min to 9 085 Lit/min ± 0.014 % of reading
15 085 L/min to 24 378 Lit/min ± 0.014 % of reading
4" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter
6" (in)
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter
8" (in)
995.0 kg/m3 to 999.7 kg/m3 ± 0.005 + 0.014 % of reading
772.4 kg/m3 to 798.8 kg/m3 ± 0.005 + 0.014 % of reading
3 614 kg/h to 6 820 kg/h ± 0.014 % of reading
52 160 kg/h to 87 100 kg/h ± 0.014 % of reading
Master Metering Method
CEC-SOP-FC-53
IS0 4185:1980
Coriolis Flow Meter
Comparison
Oil & Water Density
within DPT Density
Calibration Stand
Coriolis Flow Meter
1/2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter
2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
EQUIPMENT AND REFERENCE STANDARDS USED Mass Flow Rate (Petroleum)FO 163 000 kg/h to 272 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 3" (in) API MPMS 4.5-2016
415 179 kg/h to 545 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 4" (in) API MPMS 4.5-2016
MPMS 4.8-2013
904 211 kg/h to 1 470 000 kg/h ± 0.014 % of reading Coriolis Flow Meter 8" (in)
Volumetric Flow Rate (Petroleum)FO 60.57 L/min to 113.6 L/min ± 0.014 % of
MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 1/2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Prover Base Volume (Pipe prove, Compact Prover, Tank Prover)FO
870.6 L/min to 1 317 L/min ± 0.014 % of reading
2 729 L/min to 4 542 L/min ± 0.014 % of reading
Coriolis Flow Meter 2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 3" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
6 916 L/min to 9 085 L/min ± 0.014 % of reading Coriolis Flow Meter 4" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
6 916 L/min to 9 085 L/min ± 0.014 % of reading Coriolis Flow Meter 6" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
15 085 t/min to 24 378 L/min ± 0.014 % of reading Coriolis Flow Meter 8" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
30 Gal
Gal
Gal ± 0.017 % of reading ± 0.019 % ± 0.019 %
Water Draw Package
MPMS 12.2.4 / 4.9.2
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Fixed Storage Tanks - Road Tankers
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Volumetric method using flow meter
Calibration according to: ISO 4269:2001 (Incremental method using volumetric meters) OIML R 63:1994 “Petroleum measurement tables” OIML R 80-1:2009 “Road and rail tankers with level gauging. Part 1: Metrological and technical requirements” Calibration medium: Liquid hydrocarbons (gasoline, diesel oil, biodiesel, JET A1)
Calibration performed on site
Geometric method using strapping tape
Calibration according to: ISO 7507-1:2003 (Strapping Method) Calibration performed on site
Geometric method using total station
Calibration according to: ISO 7507-3:2006 (Optical triangulation method with reference circumference) ISO 7507-1:2003 (Remaining measurements) Calibration performed on site
Geometric method using total station
Calibration according to: ISO 7507-4:2010 (Internal electro-optical distance ranging method) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site Liquid Volume/ -
Geometric method using strapping tape
Calibration according to: ISO 129171:2002 (External strapping method) ISO 7507-1:2003 (Remaining measurements) Calibration performed on site
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
136 East South Temple, Suite 1400, Salt Lake City, UT 84111
Contact Name: Saurabh Parab Phone: 9647511694180
Accreditation is granted to the facility to perform the following calibrations:
1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree.
2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity.
3. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations. Example: Outside MicrometerFO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations.
4. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location.
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
Flow Meter Calibration
(As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA) 755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Accreditation is granted to the facility to perform the following calibrations:
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Fixed Storage Tanks - Road Tankers
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
0.5 m3 to 10 m3
CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
0.13% of nominal tank volume
(50 m3 to 10000 m3. Max tank diameter: 32m)
0.17 % of reading 0.12 % of reading 0.12 % of reading 0.11% of reading of nominal tank volume
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Volumetric method using flow meter
Calibration according to: ISO 4269:2001 (Incremental method using volumetric meters) OIML R 63:1994 “Petroleum measurement tables” OIML R 80-1:2009 “Road and rail tankers with level gauging. Part 1: Metrological and technical requirements” Calibration medium: Liquid hydrocarbons (gasoline, diesel oil, biodiesel, JET A1)
Calibration performed on site
Geometric method using strapping tape
Calibration according to: ISO 7507-1:2003 (Strapping Method) Calibration performed on site Liquid
0.19 % of reading
0.13 % of reading
0.09 % of reading
0.07 % of reading
0.06 % of reading
0.06 % of reading
(Above 250 m3. Min tank diameter: 8m)
0.06 % of reading of nominal tank volume
Geometric method using total station
Calibration according to: ISO 7507-3:2006 (Optical triangulation method with reference circumference) ISO 7507-1:2003 (Remaining measurements)
Accreditation is granted to the facility to perform the following calibrations:
Mechanical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Vertical Cylindrical Tanks
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE
200 m3
2 000 m3
10 000 m3
40 000 m3
75 000 m3
130 000 m3
(Above 200 m3 Min tank diameter: 5m)
Liquid Volume/Horizontal Cylindrical Tanks
Up to 400 m3 Maximum tank diameter: 4m Maximum tank length: 30m
CALIBRATION AND MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
0.16 % of reading
0.09 % of reading
0.07 % of reading
0.06 % of reading
0.06 % of reading
0.06 % of reading of nominal tank volume
0.065% of nominal tank volume
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Geometric method using total station
Calibration according to: ISO 7507-4:2010 (Internal electrooptical distance ranging method) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site
Geometric method using strapping tape
Calibration according to: ISO 12917-1:2002 (External strapping method) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site
1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree.
2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity.
3. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations. Example: Outside MicrometerFO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations.
4. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location.
International Association of Drilling Contractors (IADC)
American Society for Quality (ASQ)
Chartered Institute of Environmental Health (CIEH) accounted training provider
American Society for Nondestructive Testing (ASNT)
Russian Register (ISO Certification Body)
21September,2020
DearMr.Majlesein,
ThankyouforwritingtotheSecretary-Generaltoexpressyourcompany’scommitmenttothe GlobalCompact’sprinciplesintheareasofhumanrights,labour,environmentandanti-corruption.We applaud your leadership in making this decision and welcome your company’s participation in the Global Compact – the world’s largest corporate citizenship initiative, with thousands of business participants and other stakeholders from civil society, labour and government based in over 160 countries.
The Global Compact asks participating companies to pursue two complementary goals: (1) internalizethetenprincipleswithinthecompany’sstrategies,policiesandoperationsand(2)undertake projectstoadvancethebroaderdevelopmentgoalsoftheUnitedNations,particularlytheSustainable DevelopmentGoals.Weunderstandthatimplementationofuniversalprinciplesintobusinessisalongterm process, and encourage participants to follow a path of continuous improvement. This commitmentrequiresthesustainedsupportofleadershipthroughongoingactivitiesandpartnerships, as well as a company’s engagement in dialogues, willingness to learn and dedication to practical actions.
Asavoluntaryinitiative,theGlobalCompactdrawsstrengthfromourparticipants’commitment and actions. To spur implementation and progress, we provide various learning and engagement opportunitiesforourparticipants.Theseinclude:80-pluscountryandregionalnetworkswhereissues andactivitiesaredrivenatalocallevel;practicaltoolsandguidancedocumentsontheprinciplesand other priority issues; and international and local events where multi-stakeholder participants can exchange experiences, partake in learning and problem- solving exercises, engage in dialogue and identifylike-mindedorganizationsforpartneringprojects.
Further details on such activities can be found in the attached guidance document, “After the Signature:AGuidetoEngagementintheUnitedNationsGlobalCompact”andontheGlobalCompact website(www.unglobalcompact.org).
Mr.ShahriyarMajlesein CEO
CitadelEngineeringCompany
Erbil
Credibilityandaccountabilityarecriticalfactorsforadvancingtheresponsiblebusinessagenda – and for protecting the legitimacy of the Global Compact. Therefore, a key requirement for participation in the initiative is the annual submission of a Communication on Progress (COP) that describes your company’s efforts to implement the ten principles. Your company’s first COP is due within one year of joining the Global Compact, and every year thereafter. We take this integrity measureseriouslyandcompaniesthatfailtomeetconsecutiveCOPdeadlineswillbedeactivated.
The Communication on Progress serves as far more than an indication of engagement in the Global Compact, and I encourage you to regard the process as a mechanism for assessing and demonstratingtheimpactofyourcompany’sactionstoincorporateresponsiblepracticesintoday-today operations and to bring about meaningful change in society. Guidelines for preparing and submittingyourcompany’sCOParealsoavailableintheattachedguidancedocument.
Again, we thank you for joining the Global Compact. We are eager to hear your ideas and experiences,andencourageyoutoshareyourviewswithus.Westandreadytosupportyoureffortsto embrace the ten universal principles and contribute to a more sustainable and inclusive global economy.
Allofouroilcompaniesexceptoilprojects,oilexploration,Iraqidrilling,oilmarketing, and heavy engineering equipment.
Meter calibration services and calibration equipment And issuance of certificates of accreditation and calibration
Referring to the Ministerial Order (10645) on 05.04.2021, which included sending your staff to meet the invitation of ( CITADEL ENGINEERING COMPANY ) for the purposeofaccreditingits laboratoryforcalibrationofcalibrationequipment. The above company’s headquarters were visited on 08.04.2021, and its services in the calibration field were viewed, we would like to show the following:-
1- Our companies must define and study the field in which the company is globally approved (specifications and the extent to which it is used in relation to the equipment available on its site in addition to the methods by which the calibration is carried out and in the event of changing the methods, it must be re-confirmed and approved.
2- The ability of our companies to benefit from the above laboratory in calibrating the equipment according to the tasks and duties accompanying their international certification of approval directly in accordance with the paragraph (4) of the approved meeting minutes by the Minister and attached to our memorandum No. 1658 on 01.03.2020, Included (each oil company as self-financing companies) are responsible for their contracts under Law (22) for 1997 , because the law granted independence and administration with its legal personality, includes its independence by contracting in accordance with Article 19 of the aforementioned law
With best regards
Attachments
The duties & tasks of the company above.
Ali Warid Hamoud General Director
06-05-2021
Mansour Abdulmajed Jalil
Copy to : -CITADEL ENGINEERING COMPANY- info@citadel-engineering.co, for your information and to coordinate with the oil companies authorized to sign with you according to mentioned above
Ministry of planning
Iraqi Organ ization for Accreditation IQAS
AC CRET}ITATIOF{ CERTIFICATE
Iraqi Accreditation System Certify that:
Iraq- Kurdistan region- Erbil- Italian Village Is accredited according to the requirements of the standard ISO/IEC fi425:2017 (General Requirements for the Competence of Testing and Calibration Laboratories)
In the lield of:
- Pressure Calibration - Temperature Calibration - Volume Calibration - Mass Calibration - Flow Calibration - Electricity Calibration - Vibration Calibration - Chemical Calibration
This accreditation is subject to with the above standard & IQAS requirements The scope of accreditation is attached to the certificate & considered as part of it
The most recent issue of the accreditation scope is available on IQAS website https :lliq asrqop.ggvig
Accreditation is valid From 71212023 To 61212025
Initial accreditation date L0t7 t2019
I)r.
Lateef Ahmed Manager of IQAS
Dr. Mohammed Ali Tamim Deputy Prime Minister Minister of Planning
C E R T I F I CAT E
ISO 9001 : 2015
The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH
AbuDhabi
Operates a management system in accordance with the requirements of ISO 9001 : 2015 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
Management system as per C E R T I F I CAT E
ISO 14001 : 2015
The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH AbuDhabi
Operates a management system in accordance with the requirements of ISO 14001 : 2015 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) 136 East South Temple, Suite 1400, Salt Lake City, UT 84111
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system.
Inspection Body (Category-A)
(As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
PERRY JOHNSON LABORATORY ACCREDITATION, INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Organization of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17020:2012
Conformity Assessment-Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system.
Inspection Body (Category-A) (As detailed in the supplement)
Accreditation claims for such Inspection Body services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Accreditation is granted to the facility to perform the following inspections:
FIELD OF INSPECTION
Pipelines
TYPES OR RANGES OF INSPECTIONS
Piping
VT Set/NDT Set
1) Inspection Body Classifications (Type A, B or C)
SPECIFICATION, STANDARD METHOD, OR TECHNIQUE USED
ASME B31.3
Type A- An inspection body providing third party inspections
Type B- An inspection body providing first party inspections, second party inspections, or both, which forms a separate and identifiable part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services only to its parent organization (in-house inspection body)
Type C- An inspection body providing first party inspections, second party inspections, or both, which forms an identifiable but not necessarily a separate part of an organization involved in the design, manufacture, supply, installation, use or maintenance of the items it inspects and which supplies inspection services to its parent organization or to other parties, or to both
PERRYJOHNSONLABORATORY ACCREDITATION,INC.
Certificate of Accreditation
Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:
Citadel Engineering Company (CEC) Gazna Road, Erbil, Kurdistan Region, Iraq
(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:
ISO/IEC 17025:2017
This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017):
Chemical, Electrical, Mechanical, Thermodynamic, Time and Frequency, and Flow Meter Calibration (As detailed in the supplement)
Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.
For PJLA:
Tracy Szerszen President
Perry Johnson Laboratory Accreditation, Inc. (PJLA) 755 W. Big Beaver, Suite 1325 Troy, Michigan 48084
Initial Accreditation Date: Issue Date: Expiration Date: October 20, 2020 October 20, 2020 January 31, 2023
The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: www.pjlabs.com
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations:
Chemical
MEASURED INSTRUMENT, QUANTITY OR GAUGE
RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE CALIBRATION AND MEASUREMENT
CAPABILITY EXPRESSED AS AN UNCERTAINTY (±)
pH MeterF 4.01 pH 0.025 pH at 25ºC
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Accreditation is granted to the facility to perform the following calibrations: Issue: 7/2022 This supplement is
Coriolis Flow Meter 1/2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 2" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 3" (in)
API MPMS 4.5-2016
gal
API MPMS 4.8-2013
Coriolis Flow Meter 4" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 6" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Coriolis Flow Meter 8" (in)
API MPMS 4.5-2016
API MPMS 4.8-2013
Volumetric method using flow meter
Calibration according to: ISO 4269:2001 (Incremental method using volumetric meters) OIML R 63:1994 “Petroleum measurement tables” OIML R 80-1:2009 “Road and rail tankers with level gauging. Part 1: Metrological and technical requirements”
Calibration medium: Liquid hydrocarbons (gasoline, diesel oil, biodiesel, JET A1) Calibration performed on site
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Mechanical MEASURED INSTRUMENT, QUANTITY OR GAUGE
Liquid Volume/Vertical Cylindrical TanksFO
50 m3
200
2
% of reading
% of reading
Torque Wrenches /Torque DriversF
500 m3 0.13 % of reading
2 000 m3 0.09 % of reading
10 000 m3 0.07 % of reading
20 000 m3 0.06 % of reading
75 000 m3 0.06 % of reading
120 000 m3 0.06 % of reading
200 m3 0.16 % of reading
2 000 m3 0.13 % of reading
10 000 m3 0.09 % of reading
40 000 m3 0.06 % of reading
75 000 m3 0.06 % of reading
120 000 m3 0.06 % of reading
(Above 200 m3 Min tank diameter: 5m) of nominal tank volume
5 nm to 500 nm 1 % of reading
Liquid Volume/Horizontal Cylindrical TanksFO
Accreditation is granted to the facility to perform the following calibrations: Issue: 7/2022
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Geometric method using strapping tape
Calibration according to: ISO 7507-1:2003 (Strapping Method)
Calibration performed on site
500 nm to 1 000 nm 1 % of reading
1 000 nm to 2 000 nm 1 % of reading
Up to 400 m3 Maximum tank diameter: 4m Maximum tank length: 30m
0.065 % of nominal tank volume
Geometric method using total station
Calibration according to: ISO 7507-3:2006 (Optical triangulation method with reference circumference) ISO 7507-1:2003 (Remaining measurements)
Calibration performed on site
Geometric method using total station
Calibration according to: ISO 7507-4:2010 (Internal electrooptical distance ranging method) ISO 7507-1:2003 (Remaining measurements)
FLUKE 9142, 9144, Semi Standard PRT, Fluke 8846A / ASTM-E2877, EA 10/11, OIML R84
Stability Test Chamber ZF120 / ASTM E126
CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Lutron DT-2269 / OEM Manual, EUROMET cg-15
Fluke 8846A / OEM Manual, EUROMET cg-15
% of reading 40 Hz to 300 kHz
300 kHz to 1 MHz
% of reading
1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree
Page 16 of 17
Certificate of Accreditation: Supplement
Citadel Engineering Company (CEC)
Gazna Road, Erbil, Kurdistan Region, Iraq
Contact Name: Mr. Shahriyar Majlesein Phone: +1(801) 326-4626
Accreditation is granted to the facility to perform the following calibrations: Issue: 7/2022
2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity.
3. The presence of a superscript F means that the laboratory performs calibration of the indicated parameter at its fixed location Example: Outside MicrometerF would mean that the laboratory performs this calibration at its fixed location.
4. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations Example: Outside MicrometerFO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations.
5. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location.
C
E R T I F I CAT E
Management system as per
ISO 45001 : 2018
The Certification BodyTÜV Middle East hereby confirms as a result of the audit, assessment and certification decision according to ISO/IEC 17021-1:2015, that the organization
CITADELOILFIELDSERVICESLTD
POBox415287,UnitKLPFZNo:29,AlTAWEELAH AbuDhabi
operates a management system in accordance with the requirements of ISO 45001 : 2018 and will be assessed through periodic surveillance audits for conformity within the validity of the certificate
TÜVMiddleEast,MezzanineFloor,DanatTowerA,AirportRoad,PO Box46030,AbuDhabi,UAE wwwtuvme com
Cer fica on Number
Name of CAB
CITADEL OILFIELD SERVICES
Address Abu Dhabi - Al Taweelah - KLP FZ No:29, Al Taweelah, Abu Dhabi
Calibra on Laboratory
This cer ficate was issued based on the request of the conformity assessment body without any responsibility to be bared by Ministry of Industry and Advanced Technology toward others.
This is an electronic cer ficate and does not require stamp and signature Cer ficate will be invalid in case of any modifica on
Name of CAB
CITADEL OILFIELD SERVICES
Address Abu Dhabi - Al Taweelah - KLP FZ No:29, Al Taweelah, Abu Dhabi
This cer ficate was issued based on the request of the conformity assessment body without any responsibility to be bared by Ministry of Industry and Advanced Technology toward others.
This is an electronic cer ficate and does not require stamp and signature Cer ficate will be invalid in case of any modifica on
ANNUAL MEMBERSHIP CERTIFICATE 2022
This permission was issued after conducting the compliance audit and ensuring the following:
• Compliance with the requirements of Law No. 2/2010 and its Administrative Order no. 267/ 2011 regarding organizing the work of conformity assessment bodies operating in the Emirate of Dubai,
• Compliance with all conditions and instructions issued by the Emirates International Accreditation Centre.
Notes:
• This permission applies only to the scopes mentioned above.
• The validity of this permission is one year only and it should be renewed for the non accredited conformity bodies before 15 days from the date of expired.
• It is not permitted for the Conformity Assessment Body to practice activities or to use EIAC Accreditation Symbol where accreditation is mandatory unless it is accredited by EIAC
For more information about the Mandatory Accreditation Scopes; please visit EIAC website: www.eiac.gov.ae
Conformity Assessment Body should submit an application to obtain accreditation within the first year of getting this permit according to the Law no. 2/ 2010. Emirates International Accreditation Centre is entitled to take all legal actions in case of violation of any of the conditions mentioned in Law 2/2010 and its Administrative Order no. 267/ 2011.
