110926 LAB CONSUMABLES

ServiceCentre TheLabModularSystem EasyNavigationConcept

LAB CONSUMABLES

5.1 Supra Nylon Cords

5.2 Glues and Thread Lock

• Supra nylon cords and plastic strip �������������������� 4 • Lens and flex sides washers ������������������������������ 5

• Thread lock ��������������������������������������������������������� 6 • Adhesives for frames ������������������������������������������ 7 • Adhesives for lenses, glue remover ������������������� 8 • UV Glue �������������������������������������������������������������� 9

5.3 Detergents - Marker pens for Lenses

5.4 Blocking Pads - Accessories for Glazing

• Detergents for Ultrasonic Cleaners ������������������ 10 • Lens and Frame Cleaners - SprayClean ���������� 11 • Ink remover ������������������������������������������������������ 12 • Marker pens and ink ����������������������������������������� 13

• Rippled blocks and lens clamp adaptor ������������ 14 • Lens surface disks and tape ����������������������������� 15 • Blocking Pads ��������������������������������������������������� 16 • Formers, no foam, scissor, sticks ��������������������� 21

LAB MOD SYSTEM INDEX

REFRACTION & ORTHOPTIC

LENSES

LAB CONSUMABLES

EQUIPMENTS

PLIERS

TOOLS

FRAME PARTS

5.0 CONSUMABLES

2

ALL RIGHTS RESERVED ©

LAB MOD SYSTEM

5.0

FRAME PARTS TOOLS PLIERS EQUIPMENTS

• Water make up lens ������������������������������������������ 22 • Water make up frames ������������������������������������� 23 • Touch up brushes ��������������������������������������������� 24

• Polishing compounds ��������������������������������������� 25 • Polishing wheels and compounds for frames ��� 26 • Polishing wheels and compounds for lenses ��� 28

5.7 Dyes for Lenses - Neutralizers

5.8 Soldering wire and consumables

• Water soluble dyeing powders ������������������������� 30 • Bpi liquid dyes for lenses ���������������������������������� 32 • Do’s and don’ts of tinting ���������������������������������� 34 • Neutralizer solution ������������������������������������������� 36 • Chemicals ��������������������������������������������������������� 37

• Solder Rods ������������������������������������������������������ 38 • Solder Wire and Borax ������������������������������������� 38 • Isoflam �������������������������������������������������������������� 38 • Gas and Oxigen for Miniflam ���������������������������� 39 • Caustic Solution and Boric Acid ����������������������� 39 • Plating Consumables ��������������������������������������� 39 • Soldering steps ������������������������������������������������� 40

LENSES

5.6 Polishing Compounds LAB CONSUMABLES

5.5 Water Lens Make Up

REFRACTION & ORTHOPTIC INDEX

ALL RIGHTS RESERVED ©

3

LAB MOD SYSTEM

5.1 SUPRA NYLON CORDS AND PLASTIC STRIP For supra frames assembly

FRAME PARTS

CLEAR SUPRA NYLON CORDS 5m

4m

FIGURE “8”

2m

FIGURE “T”

TOOLS

ROUND

PLIERS

Ref. 01232 Ø 0,4 mm Ref. 01235 Ø 0,5 mm Ref. 01233 Ø 0,6 mm Ref. 01234 Ø 1,0 mm For metal and plastic frames

SILICONE GASKET FOR AIR-RIM

PLASTIC STRIP FOR SUPRA FRAMES ASSEMBLY 20 pcs.

50 pcs.

LAB CONSUMABLES

EQUIPMENTS

ROUND Ø 26,5 mm

Ref. 01244 For metal and plastic frames

Ref. 01242 For metal frames

Ref. 01249 Non-slip material L = 70x5 mm

Nylon Holding Plier 03465N Nylon Press-in Plier Ref. 03470N to press to pull the nylon liner in the figure “8” liner

Mounting Hook Ref. 03480 to insert the liner into the groove of the lens

Plastic strip Ref. 01249 to insert the liner into the groove of the lens

Ref. 01870 SUPRA KIT • Supra nylon cord Ø 0,5 mm clear Ref. 01235 •“Figure 8” Supra Liner clear. Ref. 01242 • “Figure T” Supra Liner clear. Ref. 01244 • Nylon Holding Plier Ref. 03465N • Nylon Press-in Plier Ref. 03470N • Mounting Hook Ref. 03480 Tray included, suitable for new LMS Cube.

INDEX

REFRACTION & ORTHOPTIC

LENSES

Ref. 01263 Clear

4

ALL RIGHTS RESERVED ©

5.1

In nylon, acetate, silicone, adhesive and rubber FLEXIBLE NYLON LENS WASHERS

4m

1.4 mm 0,20 mm

1.8 mm 0,25 mm

LARGE Ref. 01251

MEDIUM Ref. 01254

TOOLS

REGULAR Ref. 01250

1.6 mm 0,22 mm

FRAME PARTS

Dip in acetone to soften and fix into plastic frame groove

SEMI-RIGID ACETATE LENS WASHERS

SOFT SILICONE LENS WASHERS

NEW MEDIUM Ref. 01258 3,5 m - 5 pcs.

MEDIUM Ref. 01260

MEDIUM Ref. 01255 Ref. 01256 4,5 m In easy to use dispenser 1.2 mm 1.8 mm 0,25 mm 0,50 mm

4m PLIERS

1.6 mm 0,30 mm

1.2 mm 0,25 mm

EQUIPMENTS

• Adjustable with heat.

• Dip in acetone to soften and fix into plastic frame groove.

HYPO-TUBE CEMENT

SOTTILE Ref. 01266 16 m

NEW

RUBBER INSERT FOR ACETATE FLEX SIDE

REFRACTION & ORTHOPTIC

Ref. 01267 20 pcs.

1.8 mm 0,23 mm LENSES

• Prevents rotation of the astigmatism axis.

• Sticks the lens to the groove.

• Ideal for thick toric lenses.

• Easy to apply.

Ref. 01415 Silicone glue - 9 ml  10’ ÷ 12’ min.

LAB CONSUMABLES

DOUBLE SIDE ADHESIVE LENS INTERLINER

Liquid lens liner suitable for: Eyerims - Rimless - Bling crystals - Temple tips

Ref. 01873 NEW LENS WASHER KIT Ref. 01250, 01251, 01254, 01255, 01260, 01266.

Tray included, suitable for new LMS Cube.

Ø 2,6 mm Ref. 01268 20 pcs. Ø 4,5 mm Ref. 01269 20 pcs. Ø 6,0 mm

LAB MOD SYSTEM

LENS AND FLEX SIDES WASHERS

Rubber ring decreases the gap between the Acetate Flex side and Front Part.

INDEX

ALL RIGHTS RESERVED ©

5

Protects sensitive skin from allergic reactions

FRAME PARTS

LAB MOD SYSTEM

5.2 HEAT SHRINKABLE TUBES BESTSELLER

FOR THIN TEMPLES Ref. 01340 After heating: Flat side

TOOLS

4,0 mm

3,3 mt.

Round side 2,6 mm

1,1 mm

FOR MEDIUM TEMPLES Ref. 01341 After heating: Flat side

Round side 3,0 mm

1,5 mm

PLIERS

5,0 mm

3,3 mt.

FOR FLEXIBLE AND ACETATE TEMPLES

EQUIPMENTS

Ref. 01343 NEW After heating: Flat side 6,0 mm

3,3 mt.

Round side 3,6 mm

1,8 mm

4,8 mm

2,0 mm

6,0 mm

2,5 mm

Ref. 01342 LAB CONSUMABLES

8,0 mm Ref. 01344 NEW

LENSES

10,0 mm

Slide onto temple side and warm with a frame heater.

INDEX

REFRACTION & ORTHOPTIC

Easy to use!

Cut the tube a little longer to allow for shrinkage.

6

ALL RIGHTS RESERVED ©

Ref. 01876 HEAT SHRINKABLE TUBE KIT Ref. 1339, 1340, 1341, 1342.

Tray included, suitable for new LMS Cube.

5.2

To block and seal screws and nuts BLUE MEDIUM STRENGTH OIL TOLERANT

TOOLS

All Ergo bottles come with Patented “No Waste” Dispenser • • “Drop by drop” release for precise application • “Anti-desiccation” system: After use, remove glue from nozzle to avoid obstruction. The nozzle does not spill and the glue does not dry out, allowing the complete contents of the bottle to be used up.

FRAME PARTS

+ ergo® Made in Switzerland

LAB MOD SYSTEM

THREAD LOCK

PLIERS EQUIPMENTS

Ref. 01438 ergo® 4052 10 g 3h

+

LAB CONSUMABLES

Ref. 01401 Dispensing needle 4 pcs.

Ref. 01403 Dispensing needle 4 pcs.

REFRACTION & ORTHOPTIC

Ø 0,41 mm

LENSES

Ø 0,26 mm

Ref. 01431 LOCTITE 243 10 ml  2 h

Ref. 01430 LOCTITE 243 50 ml

INDEX

ALL RIGHTS RESERVED ©

7

LAB MOD SYSTEM FRAME PARTS

5.2 ADHESIVES FOR FRAMES Cyanoacrylate adhesives - Mineral filler Complete hardening after 24 hours, for best chemical and mechanical resistance.

SPECIAL FOR GLASSES

UNIVERSAL FOR PLASTIC - RUBBER METAL LEATHER

ANAEROBIC GLUE FOR METAL - PLASTIC CERAMIC - WOOD INNOVATIVE FORMULA

ACETATE GRILAMID OPTYL RUBBER - NEOPRENE

MINERAL FILLER FOR CYANOACRYLIC GLUES

NEW

NEW

Ref. 01421 GLUE 21 Anti-halo- 20 g  7” ÷ 45” sec.

Ref. 01428 ergo® 5000 30 g

Ref. 01422 ergo® 5012 + Instant superglue - 5 g  2” ÷ 30”

Ref. 01423 ergo® 5300 + Instant superglue - 20 g  2” ÷ 30”

Ref. 01405 LOCTITE 401 Instant superglue- 5 g 1” ÷ 45”

INDEX

REFRACTION & ORTHOPTIC

LENSES

LAB CONSUMABLES

EQUIPMENTS

PLIERS

TOOLS

The glue remains liquid giving more time to position the parts to be joined and hardens only in the absence of air.

8

ALL RIGHTS RESERVED ©

+

Cyanoacrylate adhesives and silicone glue - Glue Remover Gel GLUE REMOVER GEL

Ref. 01429 Liquid Gel ergo® 9153 + Does not leak - 20 g  60’ ÷ 90’ min.

Ref. 01415 HYPO-TUBE CEMENT Silicone glue - 9 ml  10’ ÷ 12’ min.

TOOLS

UNIVERSAL FOR CYANOACRYLATE GLUES

FOR GLASS POLYCARBONATE METAL AND VARIOUS MATERIALS

FRAME PARTS

CR39 HIGH INDEX

LAB MOD SYSTEM

ADHESIVES FOR LENSES, GLUE REMOVER 5.2

PLIERS EQUIPMENTS LAB CONSUMABLES

Ref. 01406 Halo-Free LOCTITE 460 Instant superglue - 20 g  2” ÷ 40” With dispensing needle

Liquid lens liner suitable for: • Rimless • Bling crystals • Temple tips

LENSES

9

INDEX

ALL RIGHTS RESERVED ©

REFRACTION & ORTHOPTIC

Easy application.

The cap with dispensing needle allows the glue to keep flowing freely.

LAB MOD SYSTEM

5.3 LENS AND FRAME CLEANING IN THE LAB Concentrated detergents for ultrasonic cleaners

FRAME PARTS

Do not corrode the frames or lenses High cleaning capacity, enhanced by the mechanical effect of the ultrasound

TOOLS

Ultrasonic cleaners employ high frequency energy that is generated electronically by a transmitter in the unit.

The electrical energy is then transformed into sound waves by a device known as a transducer.

Ultrasonic cleaners are easy to operate, require no maintenance and are economical to utilise due to the semiconductors technology.

They are the ideal equipment for the cleaning of frames and parts.

PLIERS

ACTIVE LIQUID WITH ANTIBACTERIAL PROPERTIES

INDEX

REFRACTION & ORTHOPTIC

LENSES

LAB CONSUMABLES

EQUIPMENTS

Thanks to its active enzymes, this detergent can also be used without ultrasonic cleaner, just with lukewarm water. Its antibacterial properties sanitize the spectacles.

Made in italy - 100% NO ALCOHOL Ref. 06859 1 litre bottle concentrated Add one/two cupfuls of detergent to 1 litre of water

10

ALL RIGHTS RESERVED ©

OPTOCLEAN

Cleaning concentrate specifically for ultrasonic cleaners.

Made in Germany.

Ref. 05491 1 litre bottle concentrated Add one/two cupfuls of detergent to 1 litre of water

5.3

Spray Clean with antibacterial properties, 0% alcohol

LAB MOD SYSTEM

LENS AND FRAME CLEANERS Sanitizing detergent for frames and lenses, suitable for AR coated lenses.

Wipe dry with microfiber cloth.

FRAME PARTS

INSTRUCTIONS FOR THE USE OF YOUR SPECTACLES

MICROFIBRE GLOVES

Ref. 11945 3 bottles of 150 ml each

Ref. 10490 Medium size 1 pair

Ref. 11935 Refill - 1 litre bottle

KING SIZE MICROFIBREE

PLIERS

ANTIBACTERIAL SPRAY CLEAN

TOOLS

CLEANING Use only recommended products and liquid neutral cleaners and wipe dry with a suitable cloth.

Use water if you do not have any recommended products. Do not use corrosive agents, neither alcohol or non-specific detergents, unless otherwise indicated.

35x40 cm For the practice, the optical workshop and retail gift.

EQUIPMENTS

Ref. 11992 6 pcs. assorted colours: grey, light brown, green Individually packed.

Ref. 11999 3 pcs. assorted colours Suction cup included.

LAB CONSUMABLES LENSES REFRACTION & ORTHOPTIC INDEX

ALL RIGHTS RESERVED ©

11

LAB MOD SYSTEM

To remove the marking on progressive lenses SUPPLYING THE GLASSES TO THE CUSTOMER

Centro Style marking ink cleaning solution is suitable for all types of lenses, AR coated, teflon® treated, progressive CR39 and PC lenses.

Spray onto the lens and wipe with a microfiber cloth.

The presence of the original markings on progressive lenses allows to check the correct position of the optical centres.

After this, marks can be easily removed with the Ink Remover Pen (Ref. 06973) or with the Ink Remover Spray (Ref. 06976).

INK REMOVER PEN

LAB CONSUMABLES

EQUIPMENTS

PLIERS

TOOLS

FRAME PARTS

5.3 INK REMOVER

FELT PEN

Ref. 06973 8 gr.

1 pc.

INK REMOVER BOTTLES FOR THE PRACTICE AND THE LAB LENSES

SPRAY

REFILL

Ref. 06857 Bottle 1 litre 1 pc.

INDEX

REFRACTION & ORTHOPTIC

Ref. 06976 Bottle 150 ml 3 pcs./pkg.

12

ALL RIGHTS RESERVED ©

5.3

To mark lenses

FRAME PARTS

WATERPROOF PERMANENT MARKER PENS FOR NORMAL LENSES

LAB MOD SYSTEM

MARKER PENS AND INK

Ref. 06960 Rosso, fine 0.6 mm 5 pcs.

TOOLS

Ref. 06962 Nero, fine 0.6 mm 5 pcs.

SPECIAL MARKERS

PLIERS

FOR TEFLON® COATED LENSES / SUPERHYDROPHOBIC Ref. 06964 Black, extra-fine 0.4 mm 5 pcs.

Ref. 06965 Black, fine 0.6 mm 5 pcs.

EQUIPMENTS

Ref. 06966 Red, fine 0.6 mm

5 pcs.

LAB CONSUMABLES

WATER SOLUBLE NON PERMANENT MARKER Ref. 06970 Black, extra-fine 0.4 mm Ideal to mark Press-On™.

5 pcs..

INK FOR CENTERING DEVICES LENSES REFRACTION & ORTHOPTIC

WHITE PENCIL IDEAL FOR SUN LENSES Ref. 06969 3 pcs.

NEW

INK FOR LENSMETERS Ref. 06982 Red 30 ml 1 pc.

INDEX

ALL RIGHTS RESERVED ©

13

For Automatic Lens Edgers FOR W./B. HAND EDGERS

FRAME PARTS

LAB MOD SYSTEM

5.4 RIPPLED BLOCKS AND LENS CLAMP ADAPTOR

Ref. 07368 Ø 25 mm.

Block Ø 16 mm 10 pcs.

Ref. 07369 25x20 mm Block Ø 16 mm 10 pcs.

EQUIPMENTS

PLIERS

TOOLS

Ref. 07382 Ø 25 mm.

Block Ø 16 mm For curved lenses 10 pcs.

DEBLOCKING PLIERS

Ref. 07370 Ø 25 mm.

Block Ø 16 mm 2 pcs.

Ref. 07362 25x20 mm Attacco Ø 16 mm 2 pcs.

Ref. 07375 Ø 25 mm Block Ø 14 mm 5 pcs.

Ref. 07376 Ø 18 mm Attacco Ø 14 mm 5 pcs.

Ref. 03450N

Ref. 03452N

PER MOLE N. Ref. 07380 30x17 mm Block Ø 12 mm 5 pcs.

Ref. 07377 NEW 30x17 mm Block Ø 12 mm For curved lenses - 5 pcs.

LAB CONSUMABLES

PER MOLE E. Mr. B./O. Ref. 07378 Ø 22 mm Block Ø 15,5 mm 10 pcs.

Ref. 07379 18x14 mm Block 15,5x14 mm 10 pcs.

DEBLOCKING PLIERS FOR SEMIRIGID BLOCKS

PER MOLE E.K. ETG.

LENSES

Ref. 07371 Ø 25 mm Block Ø 15,5 mm 20 pcs.

Ref. 07372 Ø 18 mm Block Ø 15,5 mm 10 pcs.

Ref. 03453N

PER MOLE H. TZ. REFRACTION & ORTHOPTIC

Ref. 07388 25x17 mm 4 pcs. (2 pairs)

Ref. 07389 20x17 mm 4 pcs. (2 pairs)

Flexible Lens Clamp Adaptor for W.B. Ref. 07385 Ø 19 mm 2 pcs.

INDEX

Ref. 07384 Ø 25 mm 2 pcs.

14

ALL RIGHTS RESERVED ©

Ref. 03­455N

5.4

Used in conjunction with blocking pads to prevent lens slippage

FRAME PARTS

Adhesive protector

LAB MOD SYSTEM

LENS SURFACE DISKS AND TAPE

BLUE ROUND PROTECTOR DISKS 1000 pcs.

TOOLS

Ø 30 mm Ref. 07330

FOR RIMLESS FRAME ASSEMBLY Ref. 07327

100 pcs.

VIDEO

NEW Clear 32x17 mm PLIERS

Holes D=2,0 mm Slot 7x3 mm

For lenses with hydrophobic and super-hydrophobic coating Ref. 07331

500 pcs.

Ref. 07335

500 pcs.

Clear rectangular 40x18 mm

FOR LENSES WITH HIGH WRAP-AROUND INCLINATION Provides excellent adhesion to hydrophobic and superRef. 07333

hydrophobic lens coatings to prevent lenses from “twisting” and “slipping” off-axis while edging.

500 pcs.

LENSES

Clear elliptical 40x26 mm

500 pcs.

Gold elliptical 40x26 mm

ALL RIGHTS RESERVED ©

15

INDEX

INSTRUCTIONS FOR USE With common adhesive pads apply one disc to each side of the lens.

With hydrophobic and super hydrophobic adhesive pads apply only one disk to the inside of the lens

REFRACTION & ORTHOPTIC

FOR VERY SLIPPERY SUPER-HYDROPHOBIC LENSES Ref. 07339

LAB CONSUMABLES

Clear elliptical 40x26 mm

EQUIPMENTS

FOR LENS CURVES UP TO BASE 6 / +4.5 DPT.

Thickness 0,4 mm - 3M Quality CR39, High Index, Shatterproof, Glass lenses

OTTIMO ione fo:rce resistance IMO rsue torq ntti-to rellean Po OTT • Extece o: sion ivhe esad rellead tece Po normale ro • Ex ntint spessore al cent Per le conan IDEALE es ns ledi r stortida orbi fopp mrd ear lsu •eId pe

PLIERS

TOOLS

FRAME PARTS

LAB MOD SYSTEM

5.4 FOR COATED LENSES

FOR FULL-EYE LENSES 1000 pcs.

For E and TP edgers - 0,8 mm For E and TP edgers - 0,4 mm For E and TP edgers - 0,4 mm

LAB CONSUMABLES

EQUIPMENTS

Ø 24 mm Ref. 07357N

LENSES

FOR FULL-EYE LENSES

REFRACTION & ORTHOPTIC

17x31 mm Ref. 07351N

1000 pcs.

INDEX

For N edgers - 0,4 mm

16

ALL RIGHTS RESERVED ©

ance ue force resist • Excellent torq on Thickness 0,6 mm - 3M Leap™ III cellent adhesi re with thin cent CR39, High Index, Shatterproof, Glass lenses •• Ex Ideal for lenses ers) (negative pow

FOR SMALL AND HALF-EYE LENSES 1000 pcs.

For W and B edgers - 0,6 mm For W and B edgers - 0,8 mm 24x24 mm Ref. 07345N pcs.

1000

PLIERS

FOR SMALL AND HALF-EYE LENSES

FOR FULL-EYE LENSES Ø 24 mm Ref. 07344N 2000 pcs.

EQUIPMENTS

Ø 18 mm Ref. 07348N 1000 pcs.

TOOLS

FOR FULL-EYE LENSES

FRAME PARTS

18x24 mm Ref. 07349N

5.4

LAB MOD SYSTEM

FOR COATED LENSES

For E and TP edgers - 0,8 mm For E and TP edgers - 0,6 mm For E and TP edgers - 0,8 mm

LAB CONSUMABLES

Ø 26 mm Ref. 07346N 1000 pcs.

FOR FULL-EYE LENSES LENSES REFRACTION & ORTHOPTIC

For N edgers - 0,6 mm

17x31 mm Ref. 07347N

1000 pcs.

INDEX

ALL RIGHTS RESERVED ©

17

LAB MOD SYSTEM FRAME PARTS

5.4 FOR COATED LENSES Thickness 0,8 mm CR39, High Index, Shatterproof, Glass lenses FOR SMALL AND HALF-EYE LENSES 20x24 mm Ref. 07354

EQUIPMENTS

PLIERS

TOOLS

1000 pcs.

For W and B edgers - 0,8 mm

FOR SMALL AND HALF-EYE LENSES

For W and B edgers - 0,8 mm

FOR FULL-EYE LENSES

Ø 18 mm Ref. 07350 1000 pcs. Ø 24 mm Ref. 07356 For E and TP edgers - 0,8 mm F

1000 pcs.

or E and TP edgers - 0,8 mm

For E and TP edgers - 0,8 mm

14x21 mm Ref. 07341 1000 pcs.

LAB CONSUMABLES

stance rque force resi • Very good to sion he • Very good ad /price ratio ity al qu nt lle ce • Ex with thin centre es ns le • Ideal for ers) (negative pow

Ø 22 mm Ref. 07340

1000 pcs.

REFRACTION & ORTHOPTIC

LENSES

FOR FULL-EYE LENSES

For N edgers - 0,8 mm

INDEX

17x31 mm Ref. 07355

18

ALL RIGHTS RESERVED ©

1000 pcs.

Thickness 0,8 mm - Optisafe® CR39, High Index, Shatterproof, Glass lenses

stance

ue force resi • Excellent torq on si he • Excellent ad rd lenses da an st • Ideal for

FRAME PARTS

FOR SMALL AND HALF-EYE LENSES

5.4

18x29 mm Ref. 07314 1000 pcs.

For W and B edgers - 0,8 mm

PLIERS

FOR SMALL AND HALF-EYE LENSES

For W and B edgers - 0,8 mm

TOOLS

LAB MOD SYSTEM

FOR HYDROPHOBIC LENSES

FOR FULL-EYE LENSES

Ø 18 mm Ref. 07312 1000 pcs.

For E and TP edgers - 0,8 mm For E and TP edgers - 0,8 mm For E and TP edgers - 0,8 mm

LAB CONSUMABLES

14x21 mm Ref. 07313 1000 pcs.

EQUIPMENTS

Ø 24 mm Ref. 07310 1000 pcs.

Ø 22 mm Ref. 07311 1000 pcs.

FOR FULL-EYE LENSES LENSES REFRACTION & ORTHOPTIC

For N edgers - 0,8 mm

17x31 mm Ref. 07315 1000 pcs.

INDEX

ALL RIGHTS RESERVED ©

19

LAB MOD SYSTEM

Thickness 0,9 mm CR39, High Index, Shatterproof, Glass lenses

RMUL A O F M IU M E R P resistance

force Excellent torque on si • Excellent adhe thin centre (negative powers) ith w es ns le r fo l • Idea

FOR SMALL AND HALF-EYE LENSES 20x24 mm Ref. 07294 1000 pcs.

For W and B edgers - 0,9 mm

TOOLS

FRAME PARTS

5.4 FOR SUPER HYDROPHOBIC LENSES

Support side, adhesive: Acrylic, red fingerlift

Lens side, adhesive: Polysiloxane, yellow fingerlift

PLIERS

The coloured fingerlifts help in correctly positioning the blocking pad: red for the support, yellow for the lens.

FOR SMALL AND HALF-EYE LENSES

FOR FULL-EYE LENSES

EQUIPMENTS

Ø 18 mm Ref. 07292 1000 pcs.

For E and TP edgers - 0,9 mm F

or E and TP edgers - 0,9 mm

For E and TP edgers - 0,9 mm

NEW 14x21 mm Ref. 07293 1000 pcs.

LAB CONSUMABLES

Ø 24 mm Ref. 07290 1000 pcs.

Ø 22­­­ mm Ref. 07291 1000 pcs.

LENSES

FOR FULL-EYE LENSES

REFRACTION & ORTHOPTIC

17x31 mm Ref. 07295 1000 pcs.

For N edgers - 0,9 mm

For N edgers - 0,9 mm

INDEX

20

ALL RIGHTS RESERVED ©

5.4

To be shaped with punch, miller cutter or scissors

LAB MOD SYSTEM

FORMERS, NO FOAM, SCISSOR, STICKS

FRAME PARTS TOOLS

Ref. 07400 Trasparent - Shape with punch cutter or scissors.

Dim.: 75x60x1.5 mm - 250 pcs.

Ref. 07411 Green - Shape with punch cutter or scissors.

Dim.: 70x60x2.0 mm - 250 pcs.

Ref. 07421 White - Shape with miller cutter.

Dim.: 70x60x2.5 mm - 250 pcs.

PLIERS EQUIPMENTS LAB CONSUMABLES

Ref. 03782 Scissor for easy pattern cutting

Cleaning and dressing diamond sticks

LENSES

Ref. 05124 FINE GRAIN 240 g Dim. 150x20x10 mm 2 pcs.

REFRACTION & ORTHOPTIC

Ref. 05125 MEDIUM GRAIN 120 g Dim. 150x20x10 mm 2 pcs.

Ref. 05126 COARSE GRAIN 80 g Dim. 150x20x10 mm 2 pcs.

INDEX

ALL RIGHTS RESERVED ©

21

LAB MOD SYSTEM FRAME PARTS

5.5 WATER MAKE UP LENS Multicolour edge customising: an exclusive service!

Ref. 07231 Grey col. 5330

PLIERS

TOOLS

Ref. 07232 Black col. 4­­

Ref. 07233 Dark Brown col. 5340

Ref. 07234 Dark Green col. 5332

Ref. 07236 Turquoise col. 5341

LENS MAKE UP is a special felt pen to decorate: • The lens edge of rimless and supra glasses.

Suitable for CR39, crystal, polycarbonate and acrylic lenses.

• Each pen can colour up to 300-500 lens pairs.

• Available in 6 classic colours.

INDEX

REFRACTION & ORTHOPTIC

LENSES

LAB CONSUMABLES

EQUIPMENTS

Ref. 07235 Bordeaux col. 5333

22

ALL RIGHTS RESERVED ©

5.5

Water felt pens to retouch frames - Multicolour metallic paints

FRAME PARTS

FRAME MAKE UP is a special felt pen to: • Colour frames • Colour screws, pad arms or other parts • Retouch scraped parts • Retouch sweat-eaten temples.

LAB MOD SYSTEM

WATER MAKE UP FRAMES

Ref. 07209 Clear Shiny 001

Ref. 07210 Yellow Gold 003 Ref. 07211 White 7364 TOOLS

201 Ref. 07

al 016 un Met

G

er 7370 02 Silv

2 Ref. 07

MAKE UP FRAME KIT

8

Re

Ref. 07200 Full assortment of 12 pens.

PLIERS

3 f. 0720

lue 03 Night B

e 108

uine Win

n 204 Ge Ref. 07

9 rown 00

iny 206 Sh Ref. 07

EQUIPMENTS

B Antique 5 0 2 7 0 Ref.

ux 014

Bordea

k 005

k iny Blac

08 Sh ef. 072

R

LAB CONSUMABLES

c Satin Bla 7 0 2 7 0 Ref.

004

a 011 rk Avan

12 Da ef. 072

R

LENSES

INSTRUCTIONS REFRACTION & ORTHOPTIC

• Clean thoroughly the part to be repaired.

• Shake felt pen very well before use.

• Press felt and apply colour onto the frame.

• Allow to air dry for 15 minutes.

• Warm in frame heater to speed up drying.

INDEX

ALL RIGHTS RESERVED ©

23

LAB MOD SYSTEM

5.5 TOUCH UP BRUSHES For customising your frames, contents 12 ml.

FRAME PARTS

METALLIC

Ref. 07111 Metallic Gold

Ref. 07121 Metallic Blue NEW

Ref. 07120 Metallic Gun Metal NEW

Ref. 07104 Matt Black

Ref. 07106 Brown

Ref. 07109 Blue

Ref. 07116 Clear NEW

Ref. 07117 White

TOOLS

Ref. 07110 Metallic Silver

PLIERS

CLASSIC

LAB CONSUMABLES

EQUIPMENTS

Ref. 07100 Shiny Black

Ref. 07112 Fire red

TOUCH-UP BRUSH KIT LENSES

Ref. 07118 Set of 12 lacquers.

(Ref. 07100 Shiny Black - 2 pcs.)

• Shake well before use.

• Apply an even layer of lacquer with the cap brush.

• • Wait a few minutes until it dries.

• To obtain tortoise effect, brush again irregularly.

INDEX

REFRACTION & ORTHOPTIC

INSTRUCTIONS

24

ALL RIGHTS RESERVED ©

5.6

For polishing and glossing of metal and plastic

FRAME PARTS

HARD POLISHING - MATT FINISH FOR ACETATE FRAMES - METAL FRAMES - LENSES

LAB MOD SYSTEM

POLISHING COMPOUNDS

TOOLS

Ref. 05280 Sand compound - 300 g For acetate frames

Ref. 05285 White compound - 300 g For white metal frames and CR39 lens edges PLIERS

FINE POLISHING AND GLOSSING FOR ACETATE FRAMES - METAL FRAMES - LENSES

EQUIPMENTS

Ref. 05286 Green compound - 300 g For white metal frames

LAB CONSUMABLES

Ref. 05282N White compound - 500 g For acetate frames and glass lens edges

Ref. 05289 Yellow compound - 250 g For gold metal frames

LENS EDGE POLISHING AND GLOSSING LENSES

Ref. 05291 Ivory compound - 300 g For polycarbonate lenses.

REFRACTION & ORTHOPTIC

• INSTRUCTIONS • Apply polishing compound in a thin even layer to mop. Repeat frequently.

• Slightly increase pressure when processing glass lenses.

• After polishing wipe off compound residuals with a soft cloth.

• Clean frame in ultrasonic bath.

INDEX

ALL RIGHTS RESERVED ©

25

LAB MOD SYSTEM

5.6 POLISHING WHEELS AND COMPOUNDS FOR FRAMES For polishing and glossing metal and plastic frames

FRAME PARTS

ACETATE FRAMES Ref. 01880 SET OF WHEELS AND COMPOUNDS FOR ACETATE FRAMES Wheels: Ref. 05200, 05205, 05225 Compounds: Ref. 05280, 05282N.

PLIERS

TOOLS

Tray included, suitable for new LMS Cube.

FOR WHITE OR GUN METAL FRAMES

Ref. 01882 SET OF WHEELS AND COMPOUNDS FOR WHITE OR GUN METAL FRAMES Wheels: Ref. 05200, 05205, 05225 Compounds: Ref. 05285, 05286.

LAB CONSUMABLES

EQUIPMENTS

Tray included, suitable for new LMS Cube.

GOLD METAL FRAMES

Ref. 01884 SET OF WHEELS AND COMPOUNDS FOR GOLD METAL FRAMES Wheels: Ref. 05200, 05205, 05225 Compounds: Ref. 05289.

CLEANING AND DE-SCALING BRUSHES

POLISHING MOPS

Ref. 05235 Brass wire Ø 90 mm 8 mm Block Ø 6.5 mm

Ref. 05205 Cotton Ø 120 mm Block Ø 8 mm

INDEX

REFRACTION & ORTHOPTIC

LENSES

Tray included, suitable for new LMS Cube.

26

ALL RIGHTS RESERVED ©

10 mm

Ref. 05220 Cotton Ø 100 mm 6 mm Block conico da Ø 8 a 6.5 mm

Technical advice

5.6 Wheels

Compounds Ref. 05280 Sand

FINE POLISHING

Ref. 05200 Flannel

Ref. 05282N White

GLOSSING

Ref. 05225 Soft cotton

Ref. 05282N White

POLISHING

Apply gentle pressure to avoid overheating.

Ref. 05205 Ref. 05220 Cotton

Ref. 05285 White

FINE POLISHING

Ref. 05200 Flannel

Ref. 05286 Green

GLOSSING

Ref. 05225 Soft cotton

Ref. 05286 Green

HARD POLISHING

Ref. 05235 Brass wire

No compound required

POLISHING

Apply gentle pressure to avoid overheating.

Ref. 05205 Ref. 05220 Cotton

Ref. 05289 Yellow

FINE POLISHING

Ref. 05200 Flannel

Ref. 05289 Yellow

GLOSSING

Ref. 05225 Soft cotton

Ref. 05289 Yellow

Apply gentle pressure to avoid overheating.

Use a thin layer of compound frequently.

Apply gentle pressure to avoid overheating.

After glossing always wipe off compound residue with a soft cloth. Clean in ultrasonic bath.

Apply gentle pressure to avoid overheating.

GLOSSING MOP

Ref. 05200 Flannel Ø 120 mm Block Ø 8 mm

Ref. 05225 Soft cotton Ø 100 mm 35 mm Tapered bore from Ø 9 to 6.5 mm Reinforced wooden centre

10 mm

REFRACTION & ORTHOPTIC

FINE POLISHING MOPS

LENSES

Apply gentle pressure to avoid overheating.

After glossing always wipe off compound residue with a soft cloth. Clean in ultrasonic bath.

LAB CONSUMABLES

Apply gentle pressure to avoid overheating.

Use a thin layer of compound regularly.

EQUIPMENTS

Apply gentle pressure to avoid overheating.

After glossing always wipe off compound residue with a soft cloth. Clean in ultrasonic bath.

PLIERS

Apply gentle pressure to avoid overheating.

Use a thin layer of compound regularly.

TOOLS

Apply gentle pressure to avoid overheating.

Ref. 05205 Ref. 05220 Cotton

rpm

FRAME PARTS

POLISHING

LAB MOD SYSTEM

POLISHING STEPS

INDEX

ALL RIGHTS RESERVED ©

27

LAB MOD SYSTEM

5.6 POLISHING WHEELS AND COMPOUNDS FOR LENSES For polishing and glossing CR39, polycarbonate or glass lenses

TOOLS

FRAME PARTS

CR39 LENSES

PLIERS

POLYCARBONATE LENSES

Ref. 01886 SET OF WHEELS AND COMPOUNDS FOR CR39 AND POLYCARBONATE LENSES Wheels: Ref. 05225, 05226, 05228 Compounds: Ref. 05282N, 05285, 05291.

GLASS LENSES

CR39 AND POLYCARBONATE LENS POLISHING Ref. 05226 Hard felt for flat edge polishing. Ø 100 mm 20 mm Bore Ø 6 mm

Ref. 05228 Hard felt, for bevel and flat edge polishing. Ø 70 mm 20 mm Bore Ø 6 mm

INDEX

REFRACTION & ORTHOPTIC

LENSES

LAB CONSUMABLES

EQUIPMENTS

Tray included, suitable for new LMS Cube.

28

ALL RIGHTS RESERVED ©

Technical advice

5.6 Compounds

Wheels

Ref. 05225 Soft cotton

Ref. 05282N White

POLISHING

Ref. 05226 Hard felt

Ref. 05291 Ivory

Ref. 05228 Hard felt with groove

Ref. 05291 Ivory

Apply gentle pressure to avoid overheating.

After glossing, always wipe off compound residue with a cloth.

Clean in ultrasonic bath.

Ref. 05225 Soft cotton

Ref. 05282N White

POLISHING

Ref. 05226 Hard felt

Ref. 05282N White

Ref. 05228 Hard felt with groove

Ref. 05282N White

Apply gentle pressure to avoid overheating.

Use a thin layer of compound.

Apply frequently.

GLOSSING

Apply slightly more pressure, keep lens turning.

After polishing always wipe off compound residue with a cloth.

Clean in ultrasonic bath.

LAB CONSUMABLES

Apply gentle pressure to avoid overheating.

After glossing, always wipe off compound residue with a cloth.

Clean in ultrasonic bath.

GLOSSING

EQUIPMENTS

Ref. 05285 White

PLIERS

Ref. 05228 Hard felt with groove

Apply gentle pressure to avoid overheating.

Use a thin layer of compound.

Apply frequently.

TOOLS

Ref. 05285 White

rpm

FRAME PARTS

Ref. 05226 Hard felt

POLISHING

LAB MOD SYSTEM

POLISHING STEPS

FOR COMPACT GLOSSING WITH COMPOUND

LENSES

Ref. 05225 Soft cotton Ø 100 mm ­ 35 mm Tapered bore from Ø 9 to 6.5 mm Reinforced wooden centre

REFRACTION & ORTHOPTIC INDEX

ALL RIGHTS RESERVED ©

29

LAB MOD SYSTEM FRAME PARTS TOOLS

5.7 WATER SOLUBLE DYEING POWDERS Biodegradable - For CR39 - High index - Polycarbonate - 10 g sachets  1÷2’

25%

50%

5÷7’

75%

9÷13’

FC1

FC2

FC3

FC1

FC2

FC3

FC1

FC2

FC3

FC1

FC2

FC3

FC1

FC2

FC3

90%

15÷25’

BROWN 1 Ref. 06830

PLIERS

BROWN SMOKE Ref. 06833

LENSES

LAB CONSUMABLES

EQUIPMENTS

BROWN 2 Ref. 06832

REFRACTION & ORTHOPTIC

GREY 1 Ref. 06838

GREY 2 Ref. 06840 INDEX

NOT SUITABLE FOR DRIVING. SIGNAL LIGHT COLOURS ARE NOT ALWAYS DISTINGUISHABLE.

30

ALL RIGHTS RESERVED ©

FC4

5.7

Biodegradable - For CR39 - High index - Polycarbonate - 10 g sachets

 5÷7’

75%

 9÷13’

90%

15÷25’

FC2

FC3

FC4

FC2

FC3

FC4

FRAME PARTS

50%

TOOLS

BLACK Ref. 06839

LAB MOD SYSTEM

WATERSOLUBLE DYEING POWDERS

PLIERS

GREEN/GREY Ref. 06841

FC2

FC2 EQUIPMENTS

LAB CONSUMABLES

GREEN Ref. 06843

COBALT Ref. 06842 FC1

FC2

FC0

LENSES

PINK Ref. 06845

RED Ref. 06847

YELLOW Ref. 06844 SUITABLE FOR NIGHT DRIVING REFRACTION & ORTHOPTIC

INSTRUCTIONS • Heat 1 litre of demineralized water at 60°C and add the bag with the dye.

• Heat solution to 93 °C and dip lens in using lens holder Ref. 06525.

• Different hues can be obtained by varying the dipping times.

The sachet protects the tint powders indefinitely.

Check the UV transmission with our UV & Visible Spectrotester Ref. 05053.

Printed colours may vary from actual lens tint.

INDEX

ALL RIGHTS RESERVED ©

31

LAB MOD SYSTEM FRAME PARTS TOOLS

5.7 BPI LIQUID DYES FOR LENSES Molecular catalytic dyes™ for CR39 - 88 ml 25%

 1’ 50% FC1

 3÷5’ 75% FC2

 7÷10’ 90% FC3

 12÷20’ FC4

SWISS CHOCOLATE Ref. 06861 FC1

FC2

FC3

FC1

FC2

FC3

FC1

FC2

FC3

FC2

FC3

FC4

PLIERS

BROWN ZS Ref. 06863

REFRACTION & ORTHOPTIC

LENSES

LAB CONSUMABLES

EQUIPMENTS

BROWN C Ref. 06864

FC4

BLACK Ref. 06870 | Ref. 06871 1 Liter Bottle

FC1

SUN GREY Ref. 06872

The dye molecules bond to the chemical structure of the lens and become part of it. Colours are more stable and the colouring time is faster.

Mix 88 ml of dye with 1 litre of distilled water.

Printed colours may vary from actual lens tint.

INDEX

NOT SUITABLE FOR DRIVING. SIGNAL LIGHT COLOURS ARE NOT ALWAYS DISTINGUISHABLE.

32

ALL RIGHTS RESERVED ©

5.7

Molecular catalytic dyes™ per CR39 - 88 ml 75%

90% 7÷10’ FC3

 12÷20’ FC4

FRAME PARTS

3÷5’ FC2

50%

FC2

FC3

PLIERS

FC0

LAB CONSUMABLES

RED Ref. 06890

FC2

EQUIPMENTS

FC2

BLUE Ref. 06885

INSTRUCTIONS FOR USE • Dissolve the contents of one bottle into 1 litre of distilled water at 60°C. • Heat solution to 93°C and dip lens in.

• Different hues can be obtained by varying the dipping times.

• Check the UV transmission with our UV & Visible Spectrotester Ref. 05053.

Printed colours may vary from actual lens tint.

GREEN Ref. 06880

TOOLS

GREEN/GREY Ref. 06883

VIOLET Ref. 06892

Clear CR39 lenses for tinting Base 12 pcs.

LAB MOD SYSTEM

BPI LIQUID DYES FOR LENSES

| Ø 73 mm | UV360 | FC0

Base 12 pcs.

| Ø 76 mm | UV360 | FC0

Ref. 06665

Ref. 06668

Ref. 06675

1,8 mm

2,2 mm

1,8 mm

2,2 mm

LENSES

Ref. 06660

REFRACTION & ORTHOPTIC INDEX

ALL RIGHTS RESERVED ©

33

•

FRAME PARTS

LAB MOD SYSTEM

5.7 DO’S AND DON’TS OF TINTING CLEANLINESS

The biggest problem in tinting is contamination. The pot must be absolutely clean before fresh tints are mixed. Any residual colour remaining in the pot will affect the new colour. Boil neutralizer in the pot to ensure perfect cleanliness.

Thoroughly rinse with clean water.

TOOLS

•

PREPARING THE TINT

LAB CONSUMABLES

EQUIPMENTS

PLIERS

Half fill the pot with distilled water and heat to 60°C (140°F) then add dye powder.

Stir mixture until dye is completely dissolved.

For liquid dyes shake the bottle well before adding hot water. Add some distilled water and flush tint pot to ensure all the contents are being used.

If required add more water to make up 1 litre of dye solution.

USE DISTILLED WATER Limestone, chlorine and water impurities can often cause inconsistencies in dye properties. Impurities can cause colour “haloes” when tinting lenses.

FLUSH THE BOTTLES WELL Make sure the tint pot is completely emptied of dye and dye sediment when mixing as it affects the composition of the colour.

DO NOT MIX DYE WITH COLD WATER Often dyes will not dissolve easily in cold water and deposits may form in the bottom of the pot. Conversely, if the dye concentrate is left to settle, the high hot plate temperature may cause crystallisation which will also affect colour consistency. Stir dyes regularly during preparation.

DO NOT MIX THE DYE WITH WATER OVER 90°C (194°F) The dye may crystallise and will not mix evenly. This could affect colour consistency.

ADVANTAGES OF MIXING THE COLOUR AT 60°C (140°F) The colour mixes homogenously as it gradually reaches the temperature of 92°C-95°C (198 - 203°F). Mixing and stirring the dyes at 60ºC for 10-15 minutes makes it very stable and ensures a homogenous colour mix.

•

HEATING AND WATER LOSS REPLACEMENT

INDEX

REFRACTION & ORTHOPTIC

LENSES

Slowly heat the solution for about 20 minutes until it reaches 92°C-95°C (198 203°F). Do not heat with a flame as that tends to concentrate the heat whereas it should be evenly spread around the dye pot. During tinting water is lost through evaporation. It is recommended that small quantities of distilled water be added to the bath to compensate for this loss. It should be at the same pot temperature when added.

DO NOT HEAT QUICKLY The temperature on the bottom and around the sides of the container is usually higher than in the centre. Fast heating may cause crystallisation which effects a colour consistency and dye life.

WATER REPLENISHEMENT Add small quantities of distilled water regularly to overcome loss due to evaporation. Wait until the dye temperature has recovered to 92°C -95°C (198°F -203°F). As more water is added, colour strength will change. A top-up of dye may also be necessary from time to time.

MIXING AND CORRECTING COLOURS When mixing and correcting colours ALWAYS rinse the lenses and lens holder in clean water before proceeding to the next colour. Contamination is the quickest and the most common way of spoiling colour consistency.

This rule also applies when adding other properties like hard coatings and when neutralising or bleaching out colour. The rule is - thoroughly wash the lens and lens holder in clean water before transferring them to another colour or process.

34

ALL RIGHTS RESERVED ©

PREPARING THE LENS

Lenses should be edged first before tinting.

Thoroughly cleaning and degreasing the lens before tinting allows for rapid and uniform tinting.

Slowly immerse the lens into the hot tint bath: do not rush as a sudden temperature change may affect the lens surface. Keep the temperature at 92°C95 °C (198 - 203°F).

FRAME PARTS

•

5.7

LAB MOD SYSTEM

TINTING STEPS

TOOLS

•

TINTING

LENSES

LENTE VERDE Too much Dip lens into Yellow Blue Grey Decolour Brown Blue Brown or Yellow Blue

LAB CONSUMABLES REFRACTION & ORTHOPTIC

•

LENTE GRIGIA Too much Dip lens into Brown Blue Purple Yellow Green Pink Blue Marrone

EQUIPMENTS

BROWN LENSES Too much Dip lens into Red Grey and Blue Grey Yellow Red, then Blue Green Blue Pink

PLIERS

Slowly immerse the lenses in holder into the hot tinting liquid to avoid splashing and lens strain.

DYE BATH SHOULD ALWAYS BE BETWEEN 92°C - 95°C (198 - 203°F) At these high temperatures, the tint and CR39 molecules bond to form part of the lens structure. The lens continues to cure in the dyeing process and has a more scratch resistant surface. At a lower temperature the dyeing cycle is longer and there is difficulty in obtaining dark tints, this increases the possibility of inferior and unstable tinting of the lens.

DO NOT DYE AT A HIGHER TEMPERATURES ABOVE 95ºC (203°F) • There is a greater water loss through evaporation.

• Crystallisation of the dye will occur and colour consistency will fail.

• Higher exposure to fumes in the working area.

• Possible softening of the lens may require more careful handling.

• More power used unnecessarily.

HOW TO OBTAIN GRADIENT LENSES If you do no have a gradient unit use the lens holder.

Prepare the lens as previously described. For prescription lenses, turn them upside down when placing them in the lens holder so the top of the lens is closest to the bottom of the tint pot. Immerse the holder until the dye covers the lens. Move the lens holder up and down and at the same time gradually withdrawing it from the solution until the lens has been completely withdrawn.

With practice a perfect gradient will be achieved. The starting depth determines the start of the gradient line.

COLOUR CORRECTION

AFTER TINTING

Immediately wash lenses and lens holder in clean cold water.

As hot lenses scratch more easily this practice will help eliminate potential lens damage. The use of MACROCLEAN microfibre cloth is recommended.

These clothes can be kept clean by regular washing.

AVOID USING PAPER TISSUES THAT ARE NOT LINT OR ACID FREE.

INDEX

ALL RIGHTS RESERVED ©

35

Neutralizer solutions for CR39

TOOLS

FRAME PARTS

LAB MOD SYSTEM

5.7 NEUTRALIZER SOLUTION

PLIERS

NEUTRALIZER SOLUTION FOR CR39 Ref. 06850 Removes dye from organic lenses.

Non flammable.

EQUIPMENTS

1 litre bottle of concentrated solution.

INDEX

REFRACTION & ORTHOPTIC

LENSES

LAB CONSUMABLES

INSTRUCTIONS • Dilute with distilled water, ratio 1:20.

• Heat to 90°C. • Dip the lens until the required decolouring grade has been achieved.

36

ALL RIGHTS RESERVED ©

5.7

UV Diamond Dye 400 XL - Heating Fluid

LAB MOD SYSTEM

CHEMICALS

FRAME PARTS TOOLS PLIERS

UV DIAMOND DYE 400 XL Ref. 06945 • Absorbs up to 99% of UV light under 400 nm.

• Increases scratch resistance.

Lens will not turn yellow and no oven required.

Bottle 450 ml

LAB CONSUMABLES

Immersion time varies according to the thickness of the lens.

EQUIPMENTS

INSTRUCTIONS UV treatment must be applied before tinting.

• Mix equal parts with distilled water.

• Heat to 92°C-95°C in a clean container • Clean the lens before treatment.

• Using a clean lens holder, immerse the lens for 10-15 min.

LENSES REFRACTION & ORTHOPTIC INDEX

ALL RIGHTS RESERVED ©

37

LAB MOD SYSTEM

5.8 SOLDERING WIRE AND CONSUMABLES

FRAME PARTS

SOLDER RODS

Solder and flux combined for ready use.

Ideal for nickel-silver, monel and stainless steel metal.

Flux

CADMIUM FREE

Ref. 06214 Yellow gold solder.

Melting range: 605°C- 635°C Pack of 10 rods - 250 mm each Ø 1,15 mm

SOLDER WIRE

BORAX

All-purpose soldering wire in silver alloy (40%).

Easy flowing, suitable for nickel silver and monel metal.

Melting range: 610°C - 650°C. To be used together with borax flux.

Promotes quick and easy flow of solder between the surfaces being soldered.

Melting range: 500°C - 700°C

Ref. 06200 Solder wire Ø 0.5 mm.

Length: 2.5 m.

Borax flux powder to be mixed with hot distilled water to make a paste.

100 g

Ref. 06202 Solder wire Ø 0.3 mm.

Length: 2.5 m.

LAB CONSUMABLES

EQUIPMENTS

PLIERS

TOOLS

Ref. 06210 Soft yellow solder.

Melting range: 655°C - 680°C Pack of 10 rods - 250 mm each Ø 1,15 mm

SOLDERING CONSUMABLES Ref. 06221 Heat shielding paste. It will protect the non-soldered area by dissipating heat for temperatures up to 3,000°C (5,432°F).

It isolates parts close to the soldering point and reduces the risk of damage to plastic and painted parts. It does not stain and washes off in water.

50 g

INDEX

REFRACTION & ORTHOPTIC

LENSES

ISOFLAM

38

ALL RIGHTS RESERVED ©

LAB MOD SYSTEM

SOLDERING AND PLATING CONSUMABLES 5.8 CONSUMABLES FOR MINIFLAM

FRAME PARTS

GAS

Ref. 06109 Butane gas.

600 ml bottle.

TOOLS PLIERS

CONSUMABLES FOR SOLDERING UNITS Ref. 06020 Caustic solution Electrolyte 0.5 litre - 2 pcs.

EQUIPMENTS

Ref. 06022 Boric acid solution - flux 0.5 litre

LAB CONSUMABLES

PLATING SOLUTIONS LENSES

Ref. 06411 Gold plating solution 50 ml

REFRACTION & ORTHOPTIC

Ref. 06415 Palladium plating solution 50 ml Ref. 06423 • Clamp electrode • Brush electrode

INDEX

ALL RIGHTS RESERVED ©

39

LAB MOD SYSTEM

5.8 SOLDERING STEPS

FRAME PARTS

•

PREPARATION

• Always wear safety glasses.

• First, remove any parts that will be affected by heat, e.g. pads, rim cover, temple tips.

• Before heating, it may be necessary to apply a large amount of protective heat shield paste ISOFLAM (Ref. 06221) over those parts that are close to the area being heated.

• Next, remove broken part by heating the area until it becomes detached.

• Use tweezers Ref. 03730 to help.

TOOLS

•

POLISHING

PLIERS

• Always prepare the surfaces to be soldered first by using the rubber abrasion wheels (Ref. 02444 - Ref. 02447).

A clean, smooth surface ensures a good result.

• Alternatively use a file.

•

PROTECTION OF THE PARTS CLOSE TO THE SOLDERING POINT

EQUIPMENTS

• Apply ISOFLAM protection paste (Ref. 06221) around the soldering point and on any components (nose pads, enamelled parts, etc.).

• After soldering, the paste can be recovered and reused by adding a few drops of distilled water.

•

POSITIONING OF THE FRAME

LAB CONSUMABLES

• Place the frame on the soldering table (Ref. 06195) to give easy access to the part being soldered.

The clamps should be kept away from the soldering area to avoid overheating.

• Rest your elbows to support the hands.

• The parts to be soldered should not be close to the table top.

•

PLANNING THE SOLDER

INDEX

REFRACTION & ORTHOPTIC

LENSES

• If you are not using SOLDER rods (Ref. 06210-6214), prepare the solder wire (Ref. 0620006202) in advance by wetting it and dipping it in borax flux powder.

• Always heat first the thicker surface as it reaches the melting point in longer time by absorbing more heat.

• Dip the soldered part in water.

• Use protective goggles during all soldering steps.

40

ALL RIGHTS RESERVED ©

5.8

Use of the different solder alloys

LAB MOD SYSTEM

SOLDERING STEPS FRONT HINGE PLATE

FRAME PARTS

The part connecting the temple hinge to the eye wire rim is subject to great stress. Having a large supporting surface it is recommended to use the solder rods Ref. 06210 - Ref. 06214, or the 0.5 mm solder wire Ref. 06200.

RIM CLOSING BLOCK

TOOLS

When soldering the closing block to the rim, as the surface area is quite small, it is recommended that a small amount of solder is carefully placed. Recommend 0.3 mm wire Ref. 06202.

HINGES

Part of the frame that allows the temple to pivot.

Recommended to use the solder rods Ref. 06210 and Ref. 06214, or the 0.5 mm solder wire Ref. 06200.

PLIERS

•

POLISHING

•

CLEANING

•

FINISHING

TOUCHUP BRUSH KIT Ref. 07100 - 07104 - 07106 - 07109 -07110 - 07111 - 07112 - 07116 07117 - 07120 - 07121.

REFRACTION & ORTHOPTIC

Ref. 07118 Set of 12 lacquers.

(Ref. 07100 Shiny Black - 2 pcs.)

LENSES

To touch-up soldered parts use these coloured lacquers. Ideal for individualising or personalising frame parts.

LAB CONSUMABLES

For best results clean the frame with an ultrasonic cleaner using concentrated detergent for ultrasonic cleaners, not to damage the frames and any type of lenses.

High cleaning capacity enhanced by the mechanical action of the ultrasonic cleaner.

ACTIVE LIQUID WITH ANTIBACTERIAL PROPERTIES Thanks to its active enzymes, this detergent can also be used without ultrasonic cleaner, just with lukewarm water. Its antibacterial properties sanitize the spectacles.

Ref. 06859 1litre bottle Add one/two cupfuls of detergent to 1 litre of water. 100% NO ALCOHOL

EQUIPMENTS

After de-scaling remove and smooth residues of solder with rubber abrasion wheels (Ref. 02444 -Ref. 02447).

Alternatively, use the brass (Ref. 02421) or steel brushes (Ref. 02422).

Next polish with silicone wheels (Ref. 02442) or hard felt brushes (Ref. 02429).

INDEX

ALL RIGHTS RESERVED ©

41