MigTectic-80

High Strength, Low Alloy MIG Wire

MigTectic 80 ®

WIRE • Used on problem steels containing high sulphur content • Excellent arc stability and increased porosity control • Produces radiographic quality welds • Excellent impact resistance and high tensile strength

DESCRIPTION:

PROCEDURE FOR USE:

MigTectic 80 is a low-alloy wire designed to produce high strength on a wide range of base metals such as problem steels containing high sulfur, sometimes encountered with carbon and low alloy Cr-Mo base metals. Its higher silicon level, with molybdenum and manganese, provides excellent arc stability and increased porosity control when welding with CO2 gas. MigTectic 80 also offers low spatter, yielding a flat bead with excellent impact values and high tensile strengths in the 80 to 90 ksi range. MigTectic 80 produces radiographic quality and porosity- free welds, even on poorly cleaned base metals.

Preparation: Clean weld area of scale and/or oxide. Check that the ground clamp is secure and in contact with a clean surface. Make sure all joints on thin gauge metals are tightly abutted with no gaps. Note: Backing strips are useful in preventing burn-through.

Technique: Be sure that the contact tip, gas diffuser, gas cup, & wire-drive rolls are suitable for the wire diameter and arc mode. Make a few practice runs to refine and optimize the Guideline Parameters.

Post-welding: Allow parts to slow cool in still air.

TECHNICAL DATA:

HEALTH AND SAFETY:

Operating Conditions:

Observe normal welding practices, respiratory protection and proper air flow pattern advised. For general welding practices, see AWS publications Z49.1 “Safety in Welding and Cutting and Allied Process”. Welding is a completely safe process when performed in accordance with proper safety measures. Become familiar with local safety regulations before beginning welding operations. DO NOT operate welding equipment or use welding materials before you have thoroughly read the proper instruction manual(s).

Current Type: DCEP (+) Typical Mechanical Values: AWS Specification: AWS A5.28 ER80S-d2 Typical Tensile Strength: 99,000 psi Typical Yield Strength: 84,000 psi Typical Elongation (1=5d): 22% Typical Impact Strength: Charpy V-notch 30 ft lbs @ -20°F:

Please refer to the Eutectic internet site for Material Safety Data Sheet (MSDS) information.

APPLICATIONS:

DISREGARDING THESE INSTRUCTIONS, AND/OR THE INSTRUCTIONS OF WELDING EQUIPMENT OR MATERIAL MANUALS, MAY BE HAZARDOUS TO YOUR HEALTH.

Excellent choice when welding ASTM A182, A217, A234 and A335 high temperature pipe, fittings, flanges and valves and A336 pressure vessel forgings.

PARAMETERS: ARC MODE

DIAMETER

AMP RANGE

VOLT RANGE

SHIELDING GAS

Short-arc

.035

75-175

19-25

75%Ar 25%CO2

Spray-arc

.035

160-200

23-26

98%Ar 2%O2

Short-arc

.045

100-200

20-27

75%Ar 25%CO2

Spray-arc

.045

170-375

23-29

98%Ar 2%O2

Spray-arc

1/16“

275-475

25-31

98%Ar 2%O2

YOUR RESOURCE FOR PROTECTION, REPAIR AND JOINING SOLUTIONS Eutectic Corporation N94 W14355 Garwin Mace Drive Menomonee Falls, WI 53051 USA P 800-558-8524 • F 262-255-5542 www.eutectic.com

Eutectic Canada 428, rue Aime Vincent Vaudreuil-Dorion, Quebec J7V 5V5 Phone: (800) 361-9439 Fax: (514) 695-8793 www.eutectic-na.com

Eutectic Mexico KM 36.5 Autopista Mexico-Quertaro 54730 Cautitlan-Izcalli Estado de Mexico, Mexico Phone: 011 (52) 55-5872-1111 e-mail: eutectic.mexico@eutectic.com.mx

Statement of Liability: Due to variations inherent in specific applications, the technical information contained herein, including any information as to suggested product applications or results, is presented without representation or warranty, expressed or implied. Without limitation, there are no warranties of merchantability or of fitness for a particular purpose. Each process and application must be fully evaluated by the user in all respects, including suitability, compliance with applicable law and non-infringement of the rights of others, and Eutectic Corporation and its affiliates shall have no liability in respect thereof.

MigTectic 80 12-21-12 © 2007, Eutectic Corporation, ® Reg. T.M., Printed in the U.S.A.