Eutectic-13496

Atomized Nickel-Based Alloy Recommended for Use with Thermal Spray Equipment

Eutectic 13496 ®

• Precise particle sizing • Exceptionally hard deposits have high resistance to abrasion and friction • May be used in a wide variety of thermal spray processes • Non-magnetic alloy

DESCRIPTION:

FINISHING PROCEDURE:

Eutectic 13496 is a high performance atomized nickel alloy powder optimized to produce hard, durable, abrasion, and friction resistant coatings with a multitude of thermal spray process equipment. Controlled composition and precise particle sizing ensures consistent deposition, fusing and hardness.

Finishing Procedure: Grinding Wheel Type: Green Silicon Carbide Grit Size: 60 - 80 Grade: H (soft) Structure: 5 Bond Type: Vitrified Wheel Speed: Use Manufacturer’s Recommendation Work Speed: 50 -65 surface feet per minute Coolant: Flood coolant with rust inhibitors in 2-5% concentration

TECHNICAL DATA: Powder Properties Melting range: Solidus; 1750°F Liquidus; 1950°F Furnace Fusing; 2170°F (set point) Powder Coverage: 0.042 lbs/ ft2 @ 0.001” Hall Flow Rate: 17 seconds Bulk Density: 4 g/cc Coating Properties Typical Hardness: Rockwell C scale, 58 Density: 7.6 g/cc Shrinkage on Fusing: 17-20 %

APPLICATIONS:

Traverse Speed • Roughing: 5-15 inches per minute • Finishing: 3-8 inches per minute In-Feed • Roughing: 0.001 inches per pass • Finishing: 0.0005 inches per pass or less Notes: 1. Before grinding, all edges and ends of coating must be chamfer ground.

2. Frequently dress the grinding wheel face to reduce friction and heat.

• Brake drums for centrifugal separators • Super heated nozzels • Pump impellers • Pump seal areas TeroDyn System 2000

TeroDyn System 3000

Nozzle

RL 200

RL 200

RotoJet

RPA 3 @ 15 psi air

-

Module Adapter

Yellow/Red Multi-Oriface set to 5

-

Oxygen

50 psi / 30 flow (FM-1 flowmeter)

50 psi / 32 flow

Acetylene

12 psi / 60 flow (FM-1 flowmeter)

12 psi / 48 flow

T-Valve

20 Clicks

-

Terometer

-

130

Carrier Gas

-

Nitrogen @ 55 psi

Spray Rate

24 lb/hr

20 lb/hr

Deposit Efficiency

90%

90%

Spray Distance

6-8 inch

6-8 inch

YOUR RESOURCE FOR PROTECTION, REPAIR AND JOINING SOLUTIONS Eutectic Corporation N94 W14355 Garwin Mace Drive Menomonee Falls, WI 53051 USA P 800-558-8524 • F 262-255-5542 www.eutectic.com

Eutectic Canada 428, rue Aime Vincent Vaudreuil-Dorion, Quebec J7V 5V5 Phone: (800) 361-9439 Fax: (514) 695-8793 www.eutectic-na.com

Eutectic Mexico KM 36.5 Autopista Mexico-Quertaro 54730 Cautitlan-Izcalli Estado de Mexico, Mexico Phone: 011 (52) 55-5872-1111 e-mail: eutectic@eutectic.com.mx

Statement of Liability: Due to variations inherent in specific applications, the technical information contained herein, including any information as to suggested product applications or results, is presented without representation or warranty, expressed or implied. Without limitation, there are no warranties of merchantability or of fitness for a particular purpose. Each process and application must be fully evaluated by the user in all respects, including suitability, compliance with applicable law and non-infringement of the rights of others, and Eutectic Corporation and its affiliates shall have no liability in respect thereof.

13496 03-07-13 © 2007, Eutectic Corporation, ® Reg. T.M., Printed in the U.S.A.