John Deere 468, 468 Silage Special and 568 Round Balers Technical Service Repair Manual TM1035
Download Repair Manual
REPAIR TECHNICAL MANUAL
Round Balers models 468, 568
TM1035 29 DEC 13 (ENGLISH)
John Deere Agriculture Pinted by Belgreen
Table of contents
FOREWORD
Section 10 - GENERAL
Group 05 - Safety
Group 10 - Specifications
Group 15 - General Information
Group 20 - Lubricants
Section 20 - DRIVE TRAIN
Group 05 - General Information
Group 10 - Diagnosing Malfunctions
Group 15 - Drive Train Protection
Group 20 - PTO Driveline
Group 25 - Remove and Install Gear Case
Group 26 - Gear Case Repair Iberica
Group 27 - Gear Case Repair Comer
Group 30 - Roll Drives
Group 35 - Rolls
Group 40 - Miscellaneous
Section 30 - HYDRAULICS
Group 05 - General Information
Group 10 - Diagnosing Malfunctions
Group 15 - Operation and Tests
Group 20 - Tensioning Valve Repair
Group 25 - Gate Lock Valve Repair
Group 30 - Cylinder Repair
Section 41 - TWINE MECHANISM—ELECTRIC
Group 05 - General Information
Group 10 - Diagnosing Malfunctions
Group 15 - Twine Wrap System Adjustments
Group 20 - Twine Wrap System Repair
Section 50 - COVEREDGE NET WRAP SYSTEM (IF EQUIPPED)
Group 05 - General Information
Group 10 - Diagnosing Malfunctions
Group 15 - Net Wrap Repair
Section 60 - ELECTRICAL SYSTEM
Group 05 - General Information
Group 10 - Common Electrical Tests and Checks
Group 15 - Diagnosing Malfunctions BALETRAK Pro System
Group 20 - Tests and Adjustments BALETRAK Pro System
Group 25 - Electrical Diagrams BALETRAK Pro System
Group 30 - BALETRAK Pro Monitor-Controller Operations
Group 35 - Repair BALETRAK Pro System
Group 40 - Connector Repair
Section 70 - PICKUP
Group 05 - General Information
Group 10 - Diagnosing Malfunctions
Group 15 - Regular Pickup Repair
Group 20 - MEGATOOTH Pickup Repair (568 Only)
Group 25 - MEGAWIDE PLUS Pickup Repair
Group 30 - Miscellaneous
Section 80 - MISCELLANEOUS
Group 05 - Wheel Repair
Group 10 - Gate Repair
Group 15 - Tension Arm Repair
Group 20 - Tongue Repair
Group 25 - Belt Repair
Group 30 - Main Frame Repair
Section 99 - DEALER FABRICATED TOOLS
Group 05 - Dealer Fabricated Tools
Foreword
This manual is written for an experienced technician. Essential tools required in performing certain service work are identified in this manual and are recommended for use.
Live with safety: Read the safety messages in the introduction of this manual and the cautions presented throughout the text of the manual.
CAUTION:
This is the safety-alert symbol. When you see this symbol on the machine or in this manual, be alert to the potential for personal injury.
The technical manual contains two types of information: diagnostics and repair. Diagnostic groups help you identify the majority of routine failures quickly. Repair groups tell how to repair the components.
Information is organized in groups for the various components requiring service instruction. At the beginning of each group are summary listings of all applicable essential tools, service equipment and tools, other materials needed to do the job, service parts kits, specifications, wear tolerances, and torque values.
Technical Manuals are concise guides for specific machines. They are on-the-job guides containing only the vital information needed for diagnosis, analysis, testing, and repair.
Fundamental service information is available from other sources covering basic theory of operation, fundamentals of troubleshooting, general maintenance, and basic type of failures and their causes.
Recognize Safety Information
Group 05 - Safety
Safety-alert symbol
This is a safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.
Follow recommended precautions and safe operating practices.
Understand Signal Words
Signal Words
A signal word DANGER, WARNING, or CAUTION is used with the safety-alert symbol. DANGER identifies the most serious hazards.
DANGER or WARNING safety signs are located near specific hazards. General precautions are listed on CAUTION safety signs. CAUTION also calls attention to safety messages in this manual.
Follow Safety Instructions
Safety Messages
Carefully read all safety messages in this manual and on your machine safety signs. Keep safety signs in good condition. Replace missing or damaged safety signs. Be sure new equipment components and repair parts include the current safety signs. Replacement safety signs are available from your John Deere dealer.
There can be additional safety information contained on parts and components sourced from suppliers that is not reproduced in this operator′s manual.
Learn how to operate the machine and how to use controls properly. Do not let anyone operate without instruction.
Keep your machine in proper working condition. Unauthorized modifications to the machine may impair the function and/or safety and affect machine life.
If you do not understand any part of this manual and need assistance, contact your John Deere dealer.
Operate Baler Safely
Keep all shields in place when operating baler.
Do not attempt to pull hay or twine from pickup when baler is running.
Never hand-feed twine or hay into baler.
All machinery should be operated by responsible persons who have been properly instructed and delegated to do so. Stand clear of baler at all times when machine is operating.
Become familiar with all controls affecting machine functions.
Do not exceed maximum bale diameter or weight limits. This can lead to accelerated wear or machine failures.
Before servicing, adjusting, or removing material from the baler, always disengage all power and stop tractor engine.
Protect Bystanders
To prevent crushing injury be sure bystanders stand clear before operating gate and unloading bale. Stay clear of gate and/or push bar while opening or closing gate.
Handle Fluids Safely—Avoid Fires
Avoid Fires
When you work around fuel, do not smoke or work near heaters or other fire hazards.
Store flammable fluids away from fire hazards. Do not incinerate or puncture pressurized containers.
Make sure machine is clean of trash, grease, and debris.
Do not store oily rags; they can ignite and burn spontaneously.
Prepare for Emergencies
First Aid Kit
Be prepared if a fire starts.
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors, ambulance service, hospital, and fire department near your telephone.
Fire Prevention
Fire Prevention
To reduce the risk of fire, follow these guidelines, especially in dry crop conditions:
Equip the baler with a water-type fire extinguisher. Large capacity water fire extinguishers are recommended because application of water can cool hot parts to prevent a fire. (See Attachments section in the Operator′s Manual.)
Keep foreign material (crop, chaff, twine, net wrap material, etc.) from building up on the machine near potentially hot areas, such as bearings on ends of baler rolls and slip clutch. Remove this buildup as part of the regular service operations.
Avoid high pressure power-washing adjacent to the bearings on ends of baler rolls to prevent damaging seals. Check bearings on ends of baler rolls regularly for early signs of failure replace as necessary. (See Lubrication and Maintenance section in the Operator′s manual.)
If noticeable changes in machine performance occur which might indicate a part is beginning to fail, stop baling immediately and investigate the cause of any sounds, smells, or sights which are unusual.
Promptly eject bales after they have been tied or wrapped. Do not use the baler to transport bales from the field. Do not bring a baler, with a bale inside it, into a building. Never leave a baler unattended with a bale inside the chamber. Use extreme care if it is necessary to park a baler in a field of dry crop or stubble. Whenever possible, park baler on bare ground or in an area surrounded by bare ground. Before leaving a baler which has been operating, verify there are no areas which are hot enough to start a fire. Do not leave the baler unattended near bales which have been baled wet, because spontaneous combustion can occur.
If service operations require using a welder, cutting torch or grinder on the baler, refer to FIRE PREVENTION WELDING in this group for guidelines which may prove useful in preventing a fire. Use extreme care when smoking around the baler.
Fire Prevention—Welding
If service operations require using a welder, cutting torch or grinder on the baler, these guidelines may prove useful in preventing a fire:
[1] - Park baler on pavement or bare ground.
[2] - Remove chaff to minimize exposure of flammable material to sparks; if chaff cannot be removed, soak it thoroughly with water before starting. Protect hoses and belts from exposure to sparks, arcs or flames.
[3] - Be sure a fully charged water-type fire extinguisher or other source of water is ready for immediate use.
[4] - Use an assistant to watch for fire while welding, cutting or grinding.
[5] - After welding, cutting or grinding is finished, wait long enough to allow parts to cool down before starting to bale. Verify that no sparks or slag have started a fire before leaving service area.
Avoid High-Pressure Fluids
High Pressure
Inspect hydraulic hoses periodically – at least once per year – for leakage, kinking, cuts, cracks, abrasion, blisters, corrosion, exposed wire braid or any other signs of wear or damage.
Replace worn or damaged hose assemblies immediately with John Deere approved replacement parts.
Escaping fluid under pressure can penetrate the skin causing serious injury.
Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure.
Search for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids.
If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result. Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available in English from Deere & Company Medical Department in Moline, Illinois, U.S.A., by calling 1-800-822-8262 or +1 309-748-5636.
Support Machine Properly
Support Properly
Always lower the attachment or implement to the ground before you work on the machine. If the work requires that the machine or attachment be lifted, provide secure support for them. If left in a raised position, hydraulically supported devices can settle or leak down.
Do not support the machine on cinder blocks, hollow tiles, or props that may crumble under continuous load. Do not work under a machine that is supported solely by a jack. Follow recommended procedures in this manual. When implements or attachments are used with a machine, always follow safety precautions listed in the implement or attachment operator′s manual.
Wear Protective Clothing
Protective Clothing
Wear close fitting clothing and safety equipment appropriate to the job.
Prolonged exposure to loud noise can cause impairment or loss of hearing. Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises.
Operating equipment safely requires the full attention of the operator. Do not wear radio or music headphones while operating machine.
Work in Clean Area
Clean Work Area
Before starting a job:
Clean work area and machine. Make sure you have all necessary tools to do your job. Have the right parts on hand.
Read all instructions thoroughly; do not attempt shortcuts.
Service Machine Safely
Safety Art
Gate Lock Lever
LEGEND: A B Gate Lock Lever Interlock Lever
To help prevent personal injury caused by unexpected movement, be sure to service the machine on a level surface. If machine is connected to a tractor, engage tractor parking brake and/or place transmission in "Park", shut off engine and remove key.
If machine is detached from tractor, block wheels to prevent movement. While working inside or around the baler with an open gate, rotate interlock lever (B) and move gate lock lever (A) to locked position (shown). Use this safety feature anytime the gate is open. Close the gate anytime the baler must be left unattended. Before servicing or adjusting baler:
1. Disengage all power.
2. Shut off tractor engine.
3. Wait until all moving parts have stopped.
4. Let all components cool.
If gate lock lever can be moved to locked position with gate fully closed, interlock lever is not adjusted properly. (See checking gate lock valve interlock lever adjustment in Operating the Baler section of machine Operator′s Manual.)
IMPORTANT:
Disconnect power supply to electronic controls when servicing electrical systems or when welding on baler. Over-voltage can damage the electronic controls.
Tie long hair behind your head. Do not wear a necktie, scarf, loose clothing, or necklace when you work near machine tools or moving parts. If these items were to get caught, severe injury could result.
Moving Parts
Remove rings and other jewelry to prevent electrical shorts and entanglement in moving parts.
Service Baler
Use an open-end wrench to turn hex gear case output shaft to aid in servicing.
Never use any type of tool or wrench on shaft while tractor engine is running. Always remove tool from shaft whenever you are finished using it.
Check PTO hookup tubular shield to ensure it is free to turn. Make necessary repairs if shield will not turn.
Safety Sharp Knives
Be careful when working around knives in the following areas. They are sharp.
CoverEdge ™ Net Wrap (if equipped)
Starter Roll Scraper (if equipped)
Safety Pinched Hand
Twine arm(s) can move unexpectedly when twine arm power is on. Stay out of the path of twine arm(s) at all times when twine arm power is on. During service or adjustment procedures for twine arm(s) or twine cutter mechanism, turn off power to twine arm(s) BEFORE placing your hands in the path of twine arm travel.
If there is crop material which is holding twine arm(s) from moving freely during twine arm cycle, it is recommended that twine arm(s) be manually positioned to release any “hold” they may have on the crop material. Turn off power to twine arm(s). This will help to make the unplugging operation easier and prevent twine arm(s) from moving unexpectedly while your hands may be in the path of the twine arm(s). Stay out of the path of twine arm(s) at all times when power to twine arm(s) is ON.
Illuminate Work Area Safely
Work Area Safely
Illuminate your work area adequately but safely. Use a portable safety light for working inside or under the machine. Make sure the bulb is enclosed by a wire cage. The hot filament of an accidentally broken bulb can ignite spilled fuel or oil.
Replace Safety Signs
Safety Signs
Replace missing or damaged safety signs. See the machine operator’s manual for correct safety sign placement.
Use Proper Lifting Equipment
Proper Lifting Equipment
Lifting heavy components incorrectly can cause severe injury or machine damage. Follow recommended procedure for removal and installation of components in the manual.
Remove Paint Before Welding or Heating
Toxic Fumes
Avoid potentially toxic fumes and dust. Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch. Remove paint before heating:
Remove paint a minimum of 100 mm (4 in.) from area to be affected by heating. If paint cannot be removed, wear an approved respirator before heating or welding. If you sand or grind paint, avoid breathing the dust. Wear an approved respirator. If you use solvent or paint stripper, remove stripper with soap and water before welding. Remove solvent or paint stripper containers and other flammable material from area. Allow fumes to disperse at least 15 minutes before welding or heating.
Do not use a chlorinated solvent in areas where welding will take place.
Do all work in an area that is well ventilated to carry toxic fumes and dust away. Dispose of paint and solvent properly.
Avoid Heating Near Pressurized Fluid Lines
Flammable Spray
Flammable spray can be generated by heating near pressurized fluid lines, resulting in severe burns to yourself and bystanders. Do not heat by welding, soldering, or using a torch near pressurized fluid lines or other flammable materials. Pressurized lines can accidentally burst when heat goes beyond the immediate flame area.
Service Tires Safely
Explosive Tire and Rim Parts
Explosive separation of a tire and rim parts can cause serious injury or death. Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job.
Always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure resulting in a tire explosion. Welding can structurally weaken or deform the wheel.
When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly. Use a safety cage if available.
Check wheels for low pressure, cuts, bubbles, damaged rims or missing lug bolts and nuts.
Keep Area Clean
Understand service procedure before doing work. Keep area clean and dry.
Never lubricate, service, or adjust machine while it is moving. Keep hands, feet , and clothing from power-driven parts. Disengage all power and operate controls to relieve pressure. Lower equipment to the ground. Stop the engine. Remove the key. Allow machine to cool.
Securely support any machine elements that must be raised for service work. Keep all parts in good condition and properly installed. Fix damage immediately. Replace worn or broken parts. Remove any buildup of grease, oil, or debris.
On self-propelled equipment, disconnect battery ground cable (-) before making adjustments on electrical systems or welding on machine.
On towed implements, disconnect wiring harnesses from tractor before servicing electrical system components or welding on machine.
Use Proper Tools
Proper Tools
Use tools appropriate to the work. Makeshift tools and procedures can create safety hazards. Use power tools only to loosen threaded parts and fasteners. For loosening and tightening hardware, use the correct size tools. DO NOT use U.S. measurement tools on metric fasteners. Avoid bodily injury caused by slipping wrenches.
Use only service parts meeting John Deere specifications.
Construct Dealer-Made Tools Safely
Construct Dealer-Made Tools Safely
Faulty or broken tools can result in serious injury. When constructing tools, use proper, quality materials, and good workmanship.
Do not weld tools unless you have the proper equipment and experience to perform the job.
Dispose of Waste Properly
Recycle Waste
Improperly disposing of waste can threaten the environment and ecology. Potentially harmful waste used with John Deere equipment include such items as oil, fuel, coolant, brake fluid, filters, and batteries.
Use leakproof containers when draining fluids. Do not use food or beverage containers that may mislead someone into drinking from them.
Do not pour waste onto the ground, down a drain, or into any water source.
Air conditioning refrigerants escaping into the air can damage the Earth’s atmosphere. Government regulations may require a certified air conditioning service center to recover and recycle used air conditioning refrigerants.
Inquire on the proper way to recycle or dispose of waste from your local environmental or recycling center, or from your John Deere dealer.
Live With Safety
Safety Systems
Before returning machine to customer, make sure machine is functioning properly, especially the safety systems. Install all guards and shields.
Group 10 - Specifications 468, 468 Silage Special and 568 Round Baler Specifications
[ (Specifications and design subject to change without notice.) ]
Number of Center Teeth40 (80 tines)56 (112 tines)
Number of Outside (Mega)Teeth16 (16 tines)8 (8 tines)
Tooth Spacing66 mm (2.6 in.)66 mm (2.6 in.)
Stripper Diameter254 mm (10 in.)254 mm (10 in.)
FORMING BELTS
Number 6 8
Width178 mm (7 in.)178 mm (7 in.)
TypeDiamond Tough™ , diamond tread friction surface, with plate-type splicesDiamond Toug h™ , diamond tread friction surface, with plate-type splices
Length(2) 13305 mm (524 in.)(4) 13305 mm (524 in.) (4) 13445 BALE WR mm (529 in.)(4) 13445 mm (529 in.) AP (BaleTrak™ Pro)
TypeTwine wrap (standard)Twine wrap (standard) CoverEdge™ Net wrap (optional)CoverEdge™ Net wrap (optional)
Control ValveOne double-acting selective control valv e. Two if equipped with hydraulicOne double-acting selective control valve. Two if equipped with hydraulic pickup lift.pickup lift.
Metric Bolt and Screw Torque Values
Metric Bolt and Screw
Metric Torque Values
Bolt or Screw Size
Class 4.8
Lubricated [ “Lubricated” means coated withDry a lubricant such as[ “Dry” means engine oil,plain or zinc fasteners withplated without phosphate and oilany lubrication, or coatings, or M20M6 to M18 and largerfasteners with fasteners with JDMJDM F13B, F13E or F13C, F13F or F13JF13H zinc flake zinc flake coating.coating. ] ]
Class 8.8 or 9.8
Lubricated [ “Lubricated” means coated withDry a lubricant such as[ “Dry” means engine oil,plain or zinc fasteners withplated without phosphate and oilany lubrication, or coatings, or M20M6 to M18 and largerfasteners with fasteners with JDMJDM F13B, F13E or F13C, F13F or F13JF13H zinc flake zinc flake coating.coating. ] ]
Class 10.9
Lubricated [ “Lubricated” means coated withDry a lubricant such as[ “Dry” means engine oil,plain or zinc fasteners withplated without phosphate and oilany lubrication, or coatings, or M20M6 to M18 and largerfasteners with fasteners with JDMJDM F13B, F13E or F13C, F13F or F13JF13H zinc flake zinc flake coating.coating. ] ]
Class 12.9
Lubricated [ “Lubricated” means coated withDry a lubricant such as[ “Dry” means engine oil,plain or zinc fasteners withplated without phosphate and oilany lubrication, or coatings, or M20M6 to M18 and largerfasteners with fasteners with JDMJDM F13B, F13E or F13C, F13F or F13JF13H zinc flake zinc flake coating.coating. ] ]
Torque values listed are for general use only, based on the strength of the bolt or screw. DO NOT use these values if a different torque value or tightening procedure is given for a specific application. For stainless steel fasteners or for nuts on U-bolts, see the tightening instructions for the specific application. Tighten plastic insert or crimped steel type lock nuts by turning the nut to the dry torque shown in the chart, unless different instructions are given for the specific application.
Shear bolts are designed to fail under predetermined loads. Always replace shear bolts with identical property class. Replace fasteners with the same or higher property class. If higher property class fasteners are used, tighten these to the strength of the original. Make sure fastener threads are clean and that you properly start thread engagement. When possible, lubricate plain or zinc plated fasteners other than lock nuts, wheel bolts or wheel nuts, unless different instructions are given for the specific application.
Unified Inch Bolt and Screw Torque Values
Unified Inch Bolt and Screw
Unified Inch Bolt and Screw Torque Values
Bolt or SAE Grade 1
Lubricated
Screw Size
SAE Grade 2 [ Grade 2 applies for hex cap screws (not hex bolts) up to 6 in. (152 mm) long. Grade 1 applies for hex cap screws over 6 in. (152 mm) long, and for all other types of bolts and screws of any length. ]
Lubricated
[ “Lubricated” means coated with a lubricant such as engine oil, fasteners with phosphate and oil coatings, or 7/8 in. and larger fasteners with JDM F13C, F13F or F13J zinc flake coating. ] Dry [ “Dry” means plain or zinc plated without any lubrication, or 1/4 to 3/4 in. fasteners with JDM F13B, F13E or F13H zinc flake coating. ] [ “Lubricated” means coated with a lubricant such as engine oil, fasteners with phosphate and oil coatings, or 7/8 in. and larger fasteners with JDM F13C, F13F or F13J zinc flake coating. ]
[ “Lubricated” Drymeans coated withDry [ “Dry” meansa lubricant such as[ “Dry” means plain or zinc platedengine oil,plain or zinc without anyfasteners withplated without lubrication, or 1/4phosphate and oilany lubrication, or to 3/4 in. fastenerscoatings, or 7/8 in.1/4 to 3/4 in. with JDM F13B,and largerfasteners with F13E or F13H zincfasteners with JDMJDM F13B, F13E or flake coating. ]F13C, F13F or F13JF13H zinc flake zinc flake coating.coating. ] ]
Lubricated
[ “Lubricated” means coated with a lubricant such as engine oil, fasteners with phosphate and oil coatings, or 7/8 in. and larger fasteners with JDM F13C, F13F or F13J zinc flake coating. ] Dry [ “Dry” means plain or zinc plated without any lubrication, or 1/4 to 3/4 in. fasteners with JDM F13B, F13E or F13H zinc flake coating. ]
Torque values listed are for general use only, based on the strength of the bolt or screw. DO NOT use these values if a different torque value or tightening procedure is given for a specific application. For plastic insert or crimped steel type lock nuts, for stainless steel fasteners, or for nuts on U-bolts, see the tightening instructions for the specific application. Shear bolts are designed to fail under predetermined loads. Always replace shear bolts with identical grade.
Replace fasteners with the same or higher grade. If higher grade fasteners are used, tighten these to the strength of the original. Make sure fastener threads are clean and that you properly start thread engagement. When possible, lubricate plain or zinc plated fasteners other than lock nuts, wheel bolts or wheel nuts, unless different instructions are given for the specific application.
Face Seal Fittings Assembly and Installation—All Pressure Applications
Face Seal O-Ring to Stud End
Installation
[1] - Inspect the fitting surfaces. They must be free of dirt and/or defects.
[2] - Inspect the O-ring. It must be free of damage and/or defects.
[3] - Lubricate O-rings and install into groove using petroleum jelly to hold in place.
SAE Grade 5, 5.1 or 5.2
SAE Grade 8 or 8.2
[4] - Push O-ring into groove with petroleum jelly so O-ring is not displaced during assembly.
[5] - Index angle fittings and tighten by hand pressing joint together to insure O-ring remains in place.
[6] - Tighten fitting or nut to torque value shown on the chart per dash size stamped on the fitting. DO NOT allow hoses to twist when tightening fittings.
Face Seal Adjustable Stud End O-Ring Installation
[1] - Back off lock nut (jam nut) and washer to full exposed turned down section of the fitting.
[2] - Install a thimble over the fitting threads to protect the O-ring from nicks.
[3] - Slide the O-ring over the thimble into the turned down section of the fitting.
[4] - Remove thimble.
Face Seal Straight Stud End O-Ring Installation
[1] - Install a thimble over the fitting threads to protect the O-ring from nicks.
[2] - Slide the O-ring over the thimble into the turned down section of the fitting.
[3] - Remove thimble.
Fitting Installation
[1] - Install fitting by hand until snug.
[2] - Position adjustable fittings by unscrewing the fitting no more than one turn.
[3] - Apply assembly torque per table.
Assembly Torque
[1] - Use one wrench to hold the connector body and one wrench to tighten nut.
[2] - For a hydraulic hose, it may be necessary to use three wrenches to prevent twist; one on the connector body, one on the nut, and one on the body of the hose fitting.
Metric Face Seal Fitting Torque Chart—Standard Pressure Applications
90° Swivel Elbow and Tube Nut
90° Adjustable Stud Elbow
Stud Straight and Tube Nut
Bulkhead Union and Bulkhead Lock Nut
Stud End Tube Nut
Swivel Nut Lock Nut
Metric Face Seal Fittings (Standard Pressure)
Tube OD/Hose IDFace Seal Tub e/Hose EndO-Ring Stud Ends
Tube Nut/S
wivelBulkhead Lock
TNourtqTuoerque Metric Tube ODIn
Metric Face Seal Fitting Torque Chart—High Pressure Applications
90° Swivel Elbow and Tube Nut
90° Adjustable Stud Elbow
Stud Straight and Tube Nut
Bulkhead Union and Bulkhead Lock Nut
Stud End Tube Nut
Swivel Nut Lock Nut
Tube OD/Hose IDFace Seal Tube/H ose EndO-Ring Stud Ends
Tube Nut/Sw Torque Torqu
SAE Face Seal Fitting Torque Chart—Standard Pressure Applications
90° Swivel Elbow and Tube Nut
90° Adjustable Stud Elbow
Stud Straight and Tube Nut
Bulkhead Union and Bulkhead Lock Nut
Stud End Tube Nut
Swivel Nut Lock Nut
Face Seal Fittings (Standard Pressure)
Nominal Tube OD/Hose IDFace Seal Tube/Hose E ndO-Ring Stud Ends Tube Nut/Swi TIMoertqriuceTBuublkehe
