RULES
TABLE OF CONTENTS
Written In C/ear Simp e English And
SAFETY RULES
IMPORTANT: To prevent injury on the io6, follow the I/'/aming, Caution, and Danger notes in this section and other sections throughout this manual. Follow the instructions carefully.
The procedures recommended and shown in this manual are good, effective service methods. However, alt possible procedures and service hazards may not be covered. Therefore. if you use a tool or procedure not recommended, you must make sure that the method you select is a safe method.
PuI the warning tag shown below on the key for the key switch when you are servicing or repairing this machine. Ona warning tag is on every new machine. You can buy additional warning tags, partnumber 331-4814, from Service Parts Suppiy.
See Other Side
WAR NING: them pulling ïhe h ydrauł+c
SERVICE MANUAL INTRODUCTION
TLt S service manual has been prepared with Table of Contents the Iatest sery gp information availabIe. Troub.’+ hooti ng, removal, disassembly. ‹nspection and i› s›:•. llatio ri procedures, and complete specification s. and tightening references can be found in m o° sections. Some sections have drawings but nr '.written p rocedure because me job is so easily done. This serv ice man ual is one of the most importan t tools available to the service technician.
Righ t, Left, Front, and Rear
The ter r1s righI hand and left-hand ano front and ' ear as used in this man‹ al indicate the right and left sides, and front 8nd rear of the machine as se*n from the operator's seat fo r correct operation c’ \.'-i .' w.0Chine or attachment.
Tex t
I f tn e serv ice manual is fo r more than o nu mac h ne or d ffferent models of components (pl aneta•y axles, gear boxes, control valves, etc.) the »•oced res have toe steps necessary to service c‘acn m‹:del
A TaD/e o/ Contents is in tne front of 'his manual. The Table of Gontents shows IN e ma in oivisions and the sections th at are in each divis ian. The individual sections, where necessary, have a Tab Ie of Co ntents on the cover or second page ›-:f t hat section.
Page Numbers
All page numbers are maae of *vo numbers separated by a dash, s inch as 4002-9. TIi ‹ i › ber before the dash is the s‹!ction n ‹imber. T. i!. » ° er following the clasn is the pa ge number in t! ..‹I section. Page numbers will be founo at the r .:.» r'gh t or left of each page.
Illustrations
III ust rat ions are pu I as near as possi bIe ':› ! he text ana are to be used as part of the text.
Special Tools
Special tools are nceoed to remove ano install, disassemble and assembie, check, anJ addust some components parts of this machine. Some special tools can be easily made locally anc the necessary information to make tne tool is in i' is service manual. Othe• special tools are ni renifficuTt to make locally anO are available frcn- S .u>i ;e Tools in the U.S. and from Jobborn Man. ! -i us r in Ganada. Use these tools accord in j to nstr uctions in t his servic * manual for you :. ›o naI safely and to do the joL correctly.
Order special tools ’rom either of the‘ *olI ›v•ing companies:
Service Tools
P,O. Box 311 Ovzatonna. Minnesota *5060
Jobborn Manufacturinr Co. 97 Frid Street Hamilton, Ontario L8P •TM3 Canada
DOWNLOAD SERVICE MANUAL ! ”!
Product Identification Number (PIN) and Serial Numbers
+'HOOUCT
l0fNTl% #NiM HUfflEFP
PART NUMBER AND IN OF 4-IN-\ BUC K ET
5N CiF ROPS CAe
830M8