Hacker Industries, Inc. - Architect Binder by BuildingOnline of Florida

CSI DIVISIONS 03 54 13 – Gypsum Cement Underlayment 09 80 00 – Sound Treatment

ARCHITECT BINDER

Hacker Industries, Inc.

The Hacker Industries, Inc. Architectural Binder provides comprehensive information to help Architects and Builders in specifying and installing FIRM-FILL® Brand Gypsum Underlayments and FIRM-FILL® Sound Control Mats (SCM). Included in the binder are Product Specifications, CAD Details, Installation Guidelines, Warranty Information, UL Fire Rated Design listings and Acoustical Design Guidelines. Division 03 54 13 Gypsum Cement Underlayments FIRM-FILL® Brand Gypsum Underlayments are designed for use in multi-family housing, hospitality and commercial buildings to satisfy acoustical ratings and fire codes while providing flat, quick drying surfaces for finished floor coverings. All FIRM-FILL Brand Gypsum Underlayments meet ASTM F2419, Standard Practice for Installation of Thick Poured Gypsum Concrete Underlayments and the Preparation of the Surface to Receive Resilient Floor Coverings, and installation methods listed by the Tile Council of North America (TCNA). Division 09 80 00 Sound Treatment FIRM-FILL® SCM are durable, lightweight sound control mats that provide a quieter environment and meets demanding project specifications. FIRM-FILL® SCM are engineered to limit impact sound transmission between floors when used in conjunction with a FIRMFILL® Brand Gypsum Underlayments. FIRM-FILL® SCM can improve IIC ratings 15-25 points and carry a Class-A fire rating under ASTM E84.

Let Our Products Floor You™. This package includes technical information and expertiese that is confidential information of Hacker Industries, Inc. Its contents are to be maintained in the strictest confidence. The information contained herein is based on our best knowledge, experience, and research to date. It is not guaranteed to be accurate and we are not responsible for use of the information. This information is subject to change without notice. This information is the property of Hacker Industries, Inc., and is not to be reproduced in any form without the written consent of: Hacker Industries, Inc. 1600 Newport Center Drive, Suite 275 Newport Beach, CA 92660 USA Toll Free Tel. (800) 642-3455 (949) 729-3101 / Fax (949) 729-3108 www.HackerIndustries.com info@HackerIndustries.com

TABLE OF CONTENTS Overview • Introduction ............................................................................................................................................................................................. ii • Choosing the Right Gypsum Floor Underlayment ....................................................................................................................1 • Choosing the Right Sound Control Mat ........................................................................................................................................3 Division 03 54 13 Gypsum Cement Underlayments: Hacker Floor Underlayments • FIRM-FILL® Gypsum Concrete .............................................................................................................................................page 6 • Product Submittal ...........................................................................................................................................................................8 • 3-Part Specifications ................................................................................................................................................................... 13 • Project References ....................................................................................................................................................................... 16 • FIRM-FILL® 2010+ .................................................................................................................................................................. page 17 • Product Submittal ........................................................................................................................................................................ 19 • 3-Part Specifications ................................................................................................................................................................... 23 • Project References ....................................................................................................................................................................... 26 • FIRM-FILL® 3310 Classic ...................................................................................................................................................... page 27 • Product Submittal ........................................................................................................................................................................ 29 • 3-Part Specifications ................................................................................................................................................................... 33 • Project References ....................................................................................................................................................................... 37 • FIRM-FILL® 3310+ .................................................................................................................................................................. page 38 • Product Submittal ........................................................................................................................................................................ 40 • 3-Part Specifications ................................................................................................................................................................... 44 • Project References ....................................................................................................................................................................... 48 • FIRM-FILL® High Strength ................................................................................................................................................. page 49 • Product Submittal ........................................................................................................................................................................ 51 • 3-Part Specifications ................................................................................................................................................................... 56 • Project References ....................................................................................................................................................................... 59 • FIRM-FILL® 4010+ .................................................................................................................................................................. page 60 • Product Submittal ........................................................................................................................................................................ 62 • 3-Part Specifications ................................................................................................................................................................... 68 • Project References ....................................................................................................................................................................... 71 • FIRM-FILL® CMD ..................................................................................................................................................................... page 72 • Product Submittal ........................................................................................................................................................................ 74 • 3-Part Specifications ................................................................................................................................................................... 78 • Project References ....................................................................................................................................................................... 81 • GYP-SPAN® Radiant .............................................................................................................................................................. page 82 • Product Submittal ........................................................................................................................................................................ 84 • 3-Part Specifications ................................................................................................................................................................... 87 • Project References ....................................................................................................................................................................... 90

iii

Division 09 80 00 Sound Treatment : Sound Control Mats • FIRM-FILL® SCM-125 ............................................................................................................................page 92 • Product Submittal ........................................................................................................................................................................ 94 • 3-Part Specifications .................................................................................................................................................................100 • FIRM-FILL® SCM-250 ..........................................................................................................................page 103 • Product Submittal ......................................................................................................................................................................105 • 3-Part Specifications .................................................................................................................................................................112 • FIRM-FILL® SCM-400 ..........................................................................................................................page 115 • Product Submittal ......................................................................................................................................................................117 • 3-Part Specifications .................................................................................................................................................................123 • FIRM-FILL® SCM-750 ..........................................................................................................................page 127 • Product Submittal ......................................................................................................................................................................128 • 3-Part Specifications .................................................................................................................................................................131 • Hacker Sound Mat II ..........................................................................................................................page 134 • Product Submittal ......................................................................................................................................................................136 • 3-Part Specifications .................................................................................................................................................................140 • Project References .............................................................................................................................page 143 Division 03 54 13 Gypsum Cement Underlayment : Quick Reference • Quick Reference .................................................................................................................................page 145

CHOOSING THE RIGHT GYPSUM UNDERLAYMENT

US. CALIFORNIA PROPOSITION 65: WARNING: This product contains a chemical known to the State of California to cause cancer. ADDITIONAL STORAGE AND HANDLING INSTRUCTIONS Store in a dry place. Dew point conditions or other conditions causing presence of moisture may harden product during storage.

For additional information about this product, refer to the Hacker Industries Safety Data Sheet (SDS). A copy of the SDS can be obtained by writing to: Hacker Industries, Inc. 1600 Newport Center Drive, Newport Beach, CA 92660

if you feel unwell. If in eyes: Rinse cautiously with water for several

rinsing. Immediately call a poison center/doctor. If on skin: Wash with

plenty of water. If skin irritation or rash occurs: Get medical advice/ Commercial grade strengths attention. Take off contaminated clothing and wash before reuse.

® Sound Mats and Primers Use with FIRM-FILL treatment (see section 4 on the SDS).

IF exposed or concerned: Get medical advice/attention. Specific

STORAGE: Store locked up. Store away from acids, phosphorus, diazomethan, and aluminum (at high temperatures). Protect from moisture.

HACKER INDUSTRIES, INC.

NET WT. 80.0 LB. (36.3 kg) GROSS WT. 80.5 LB. (36.5 kg)

FLOOR TOPPING MIXTURE FIRE RESISTANCE CLASSIFICATION SEE UL FIRE RESISTANCE DIRECTORY 99L4 HACKER INDUSTRIES, INC. - R10474 FOR MIXING INSTRUCTIONS PLEASE REFER TO SPECIFIC DESIGN NUMBER

if you feel unwell. If in eyes: Rinse cautiously with water for several

rinsing. Immediately call a poison center/doctor. If on skin: Wash with

® ofSound plenty water. If skin irritation or rash occurs: Get medical advice/ Use with FIRM-FILL Mats and Primers attention. Take off contaminated clothing and wash before reuse. IF exposed or concerned: Get medical advice/attention. Specific treatment (see section 4 on the SDS).

STORAGE: Store locked up. Store away from acids, phosphorus, diazomethan, and aluminum (at high temperatures). Protect from moisture.

GYPSE DE BÉTON

GYPSUM CONCRETE

Firm-Fill 3310

Classic

RADIANT

GYPSUM CONCRETE

PREVENTION: Obtain special instructions before use. Do not R ADIANT GYPSE BÉTON handle until all safety precautions have been read and understood.

Do not breathe dust. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated work clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. After

mixing with water, do not allow prolonged contact with skin until the Gypsum-Based Cement for Radiant Heating Applications product has completely hardened and cooled.

+ + +

Appropriate for Hydronic or Electric Heating Systems RESPONSE: If swallowed: Rinse mouth. Call a poison center/doctor if you feel unwell. If in eyes: Rinse cautiously with water for several

minutes. Remove contact lenses, if present and easy to do. Continue Uniform heat transfer

rinsing. Immediately call a poison center/doctor. If on skin: Wash with

STORAGE: Store locked up. Store away from acids, phosphorus, diazomethan, and aluminum (at high temperatures). Protect from moisture.

RADIANT GYPSUM CONCRETE

GYPSE DE BÉTON

clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. After

Lightweight and RESPONSE: high-strength If swallowed: Rinse mouth. Call a poison center/doctor

minutes. Remove contact lenses, if present and easy to do. Continue Smooth, flat surface

GYPSUM CONCRETE

Do not breathe dust. Wash thoroughly after handling. Do not

mixing with water, do not allow prolonged contact with skin until the Gypsum-Based Cement for Corrugated Steel Deck product has completely hardened and cooled.

Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes damage to organs (lung) through prolonged or repeated exposure.

D A N G E R

Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes damage to organs (lung) through prolonged or repeated exposure. PREVENTION: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not breathe dust. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated work clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. After mixing with water, do not allow prolonged contact with skin until the product has completely hardened and cooled. RESPONSE: If swallowed: Rinse mouth. Call a poison center/doctor if you feel unwell. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison center/doctor. If on skin: Wash with plenty of water. If skin irritation or rash occurs: Get medical advice/ attention. Take off contaminated clothing and wash before reuse. IF exposed or concerned: Get medical advice/attention. Specific treatment (see section 4 on the SDS). STORAGE: Store locked up. Store away from acids, phosphorus, diazomethan, and aluminum (at high temperatures). Protect from moisture.

DISPOSAL: Dispose of contents/container in accordance with applicable regulations.

SUPPLEMENTAL INFORMATION: Heat develops as product hardens. May cause serious burns during hardening (rehydration) resulting in possible permanent injury.

US. CALIFORNIA PROPOSITION 65: WARNING: This product contains a chemical known to the State of California to cause cancer.

ADDITIONAL STORAGE AND HANDLING INSTRUCTIONS Store in a dry place. Dew point conditions or other conditions causing presence of moisture may harden product during storage.

Firm-Fill

1600 Newport Center Drive, Newport Beach, CA 92660

GYPSE DE BÉTON eat, drink or smoke when using this product. Contaminated work

D A N G E R

Gyp-Span

DISPOSAL: Dispose of contents/container in accordance with applicable regulations.

Firm-Fill

Manufactured for

PREVENTION: Obtain special instructions before use. Do not GYPSUM CONCRETE handle until all safety precautions have been read and understood.

+ + +

El contenido y los recipientes se deben desechar de acuerdo a los reglamentos que correspondan.

Firm-Fill CMD

Cap new or damaged concrete RESPONSE: If swallowed: Rinse mouth. Call a poison center/doctor

minutes. Remove contact lenses, if present and easy to do. Continue Smooth, flat surface

GYPSE DE BÉTON

clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. After

+ + + +

GYPSUM CONCRETE

HIGH STRENGTH

GYPSE DE BÉTON

Do not breathe dust. Wash thoroughly after handling. Do not

mixing with water, do not allow prolonged contact with skin until the Gypsum Cement Ideal for Renovation and Concrete Repair Use product has completely hardened and cooled.

Eliminación

Información suplementaria

ATTENTION! LE DIOXYDE DE TITANE Suceptible d’être cancérigène MESURES DE PREVENTION: En utilisant le produit, fournir ventilation d’éc happement locale et générale pour garder des concentrations en poussières dans l’air au-dessous des limites d’exposition. Utilise les méthodes de l’eau pour réduire la génération de la poussière. PREMIERS SOINS: Contact avec les yeux: Rincer immédiatement les yeux à grande eau pendant au moins 15 minutes. Obtenir une assistance médicale si les irritations se développent ou persistent. Contact cutané: En cas de contact avec la peau, se laver immédiatement avec du savon et de l’eau. Obtenir une assistance médicale si les irritations se développent ou persistent. Inhalation: Deplacer à l’air libre. Si les symptômes peristent, obtenir de l’attention médicale. VOIR LA FICHE SIGNALETIQUE POUR CE PRODUIT

HACKER INDUSTRIES, INC. | Newport Beach, CA 92660

FLOOR TOPPING MIXTURE FIRE RESISTANCE CLASSIFICATION SEE UL FIRE RESISTANCE DIRECTORY 99L4 HACKER INDUSTRIES, INC. - R10474

Se produce calor a medida que se endurece el producto. Puede causar quemaduras graves mientras se endurece (rehidratación), lo que puede ocasionar lesiones permanentes. FOR MIXING INSTRUCTIONS PLEASE REFER TO SPECIFIC DESIGN NUMBER For additional information about this product, refer to the Hacker Industries Safety Data Sheet (SDS). A copy of the SDS can be obtained by writing to: Hacker Industries, Inc. 1600 Newport Center Drive, Newport Beach, CA 92660

RADIANT

GYPSUM CONCRETE

GYPSE DE BÉTON eat, drink or smoke when using this product. Contaminated work

NET WT. 80.0 LB. (36.3 kg) GROSS WT. 80.5 LB. (36.5 kg)

Code Approvals ER #4147 MR #1255e CA472 (Modified), F2419

D A N G E R

Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes damage to organs (lung) through prolonged or repeated exposure.

WARNING! May Cause Cancer PRECAUTIONS: When using product: Provide local and general exhaust ventilation to keep airborne dust concentrations below exposure limits. Use wet methods, if appropriate, to reduce the generation of dust. FIRST AID: Eye contact: Immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention if irritation develops or persists. For skin contact, wash immediately with soap and water. Get medical attention immediately if irritation develops or persists. Inhalation: Remove to fresh air. If symptoms persist, obtain medical attention. SEE SAFETY DATA SHEET FOR THIS PRODUCT

1600 Newport Center Drive, Newport Beach, CA 92660

FOR MIXING INSTRUCTIONS PLEASE REFER TO SPECIFIC DESIGN NUMBER

Firm-Fill CMD

Firm-Fill

Manufactured for

P403 + P233 - Almacenar en un lugar bien ventilado. Guardar el recipiente herméticamente cerrado. Almacenar lejos de materiales incompatibles (ver sección 10 de la FDS). Proteger de la humedad.

GYPSUM CONCRETE

PREVENTION: Obtain special instructions before use. Do not GYPSUM CONCRETE handle until all safety precautions have been read and understood.

HACKER INDUSTRIES, INC.

Almacenamiento

R ADIANT GYPSE BÉTON

Quick-drying

Use with FIRM-FILL® Sound Mats and Primers

Respuesta

FLOOR TOPPING MIXTURE FIRE RESISTANCE CLASSIFICATION SEE UL FIRE RESISTANCE DIRECTORY 99L4 HACKER INDUSTRIES, INC. - R10474

Gyp-Span

Economical solution

Corrects damaged concrete

GYPSE DE BÉTON

+ + + +

Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes damage to organs (lung) through prolonged or repeated exposure.

P301 + P330 + P312 - En caso de ingestión: Enjuagarse la boca. Llamar a un centro de toxicología o a un médico si la persona se encuentra mal. P305 + P351 + P338 - EN CASO DE CONTACTO CON LOS OJOS: Enjuagar con agua cuidadosamente durante varios minutos. Quitar las lentes de contacto cuando estén presentes y pueda hacerse con facilidad. Proseguir con el lavado. P310 - Llamar inmediatamente a un CENTRO DE TOXICOLOGÍA/médico. P302 + P352 - EN CASO DE CONTACTO CON LA PIEL: Lavar con agua y jabón abundantes. P333 + P313 - En caso de irritación cutánea o sarpullido: Consultar a un médico. P362 - Quitar la ropa contaminada y lavarla antes de volverla a usar. P308 + P313 - EN CASO DE exposición demostrada o supuesta: consultar a un médico. Tratamiento específico (vea la sección 4 en la hoja de datos de seguridad).

1600 Newport Center Drive, Newport Beach, CA 92660 949.729.3101 / 800.642.3455

ICC-ES HUD ASTM

Firm-Fill 4010

SUPPLEMENTAL INFORMATION: Heat develops as product hardens. May cause serious burns during hardening (rehydration) resulting in possible permanent injury.

Prevención P201 - Procurarse las instrucciones antes del uso. P202 - No manipular antes de haber leído y comprendido todas las precauciones de seguridad. P260 - No respirar polvos. P264 - Lavarse cuidadosamente después de la manipulación. P270 - No comer, beber o fumar mientras se manipula este producto. P272 - La ropa de trabajo contaminada no debe salir del lugar de trabajo. P280 - Usar equipo de protección para los ojos/la cara. P280 - Usar guantes de protección. P281 - Utilizar un equipo de protección individual, según corresponda. Después de mezclar con agua, no permita el contacto prolongado con la piel mientras el producto no se haya endurecido y enfriado por completo.

Manufactured for

RESPONSE: If swallowed: Rinse mouth. Call a poison center/doctor if you feel unwell. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison center/doctor. If on skin: Wash with plenty of water. If skin irritation or rash occurs: Get medical advice/ attention. Take off contaminated clothing and wash before reuse. IF exposed or concerned: Get medical advice/attention. Specific treatment (see section 4 on the SDS).

DISPOSAL: Dispose of contents/container in accordance with applicable regulations.

H302 - Nocivo en caso de ingestión. H315 - Provoca irritación cutánea. H317 - Puede provocar una reacción cutánea alérgica. H318 - Provoca lesiones oculares graves. H350 - Puede provocar cáncer. H372 - Provoca daños en los órganos (pulmones) tras exposiciones prolongadas o repetidas.

HACKER INDUSTRIES, INC.

NET WT. 80.0 LB. (36.3 kg) GROSS WT. 80.5 LB. (36.5 kg)

FOR MIXING INSTRUCTIONS PLEASE REFER TO SPECIFIC DESIGN NUMBER

GYPSUM CONCRETE

Gypsum Cement Ideal for Concrete Repair and Leveling

PREVENTION: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not breathe dust. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated work clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. After mixing with water, do not allow prolonged contact with skin until the product has completely hardened and cooled.

STORAGE: Store locked up. Store away from acids, phosphorus, diazomethan, and aluminum (at high temperatures). Protect from moisture.

Mexico

Peligro Indicación de peligro

HACKER INDUSTRIES, INC. | Newport Beach, CA 92660

FLOOR TOPPING MIXTURE FIRE RESISTANCE CLASSIFICATION SEE UL FIRE RESISTANCE DIRECTORY 99L4 HACKER INDUSTRIES, INC. - R10474

Firm-Fill CMD

GYPSE DE BÉTON

HIGH STRENGTH

GYPSUM CONCRETE

HIGH STRENGTH

GYPSE DE BÉTON

1600 Newport Center Drive, Newport Beach, CA 92660

D A N G E R

Firm-Fill 4010

GYPSE DE BÉTON

GYPSUM CONCRETE

Firm-Fill

Firm-Fill GYPSUM CONCRETE

NET WT. 80.0 LB. (36.3 kg) GROSS WT. 80.5 LB. (36.5 kg)

FOR MIXING INSTRUCTIONS PLEASE REFER TO SPECIFIC DESIGN NUMBER

Firm-Fill

NET WT. 80.0 LB. (36.3 kg) GROSS WT. 80.5 LB. (36.5 kg)

Manufactured for

HACKER INDUSTRIES, INC.

HACKER INDUSTRIES, INC. | Newport Beach, CA 92660

FLOOR TOPPING MIXTURE FIRE RESISTANCE CLASSIFICATION SEE UL FIRE RESISTANCE DIRECTORY 99L4 HACKER INDUSTRIES, INC. - R10474

Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated work clothing should not be allowed doctor if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER/doctor. IF ON SKIN: Wash with plenty of water. If skin irritation or rash occurs:

Se procurer les instructions avant utilisation. Ne pas manipuler avant d’avoir lu et compris toutes les précautions de sécurité. Ne pas respirer les poussières. Se laver soigneusement après manipulation. Ne pas manger, boire ou fumer en manipulant ce produit. Les vêtements de travail contaminés ne devraient pas sortir du lieu de travail. Porter des gants/vêtements de protection/ équipement de protection des yeux/du visage. Après avoir mélangé le produit avec de l’eau, éviter tout contact prolongé avec la peau jusqu’à ce que le produit ait complètement durci et refroidi. En cas d’ingestion : Rincer la bouche. appeler un centre antipoison ou un médecin en cas de malaise. EN CAS DE CONTACT AVEC LES YEUX: Rincer avec précaution à l’eau pendant plusieurs minutes. Enlever les lentilles de contact si la victime en porte et si elles peuvent être facilement enlevées. Continuer à rincer. Appeler immédiatement un CENTRE ANTIPOISON/un médecin. EN CAS DE CONTACT AVEC LA PEAU: Laver abondamment à l’eau. En cas d’irritation ou d’éruption cutanée: Obtenir une consultation médicale ou des soins médicaux. Enlever les vêtements contaminés et les laver avant réutilisation. EN CAS d’exposition prouvée ou suspectée : Demander un avis médical/Consulter un médecin. Traitement spécifique (voir rubrique 4 de la FS). Entreposer dans un endroit bien ventilé. Garder le contenant fermé hermétiquement. Conserver à l’écart de matières incompatibles (voir rubrique 10). Protéger de l’humidité. Éliminer le contenu/contenant conformément à la réglementation applicable.

hardening (rehydration) resulting in possible permanent injury.

out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. After mixing with water, do not allow Low water demand prolonged contact with skin until the product has completely hardened and cooled. If swallowed: Rinse mouth. Call a poison center/

® contaminated clothing Get medical advice/attention. Take offSound and wash it before reuse. IF exposed or concerned: Get medical advice/ Use with FIRM-FILL Mats and Primers attention. Specific treatment (see section 4 on the SDS). Store in a well-ventilated place. Keep container tightly closed. Store away from

incompatible materials (see Section 10 of the SDS). Protect from moisture. Dispose of contents/container in accordance with applicable regulations.

Firm-Fill ATTENTION! LE DIOXYDE DE TITANE Suceptible d’être cancérigène MESURES DE PREVENTION: En utilisant le produit, fournir ventilation d’éc happement locale et générale pour garder des concentrations en poussières dans l’air au-dessous des limites d’exposition. Utilise les méthodes de l’eau pour réduire la génération de la poussière. PREMIERS SOINS: Contact avec les yeux: Rincer immédiatement les yeux à grande eau pendant au moins 15 minutes. Obtenir une assistance médicale si les irritations se développent ou persistent. Contact cutané: En cas de contact avec la peau, se laver immédiatement avec du savon et de l’eau. Obtenir une assistance médicale si les irritations se développent ou persistent. Inhalation: Deplacer à l’air libre. Si les symptômes peristent, obtenir de l’attention médicale. VOIR LA FICHE SIGNALETIQUE POUR CE PRODUIT

Hazard statement

Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes Premium damage strength to organs (lung) through prolonged or repeated exposure. Heat develops as product hardens. May cause serious burns during

Precautionary statement Fire-resistant Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not breathe dust.

Nocif en cas d’ingestion. Provoque une irritation cutanée. Peut provoquer une allergie cutanée. Provoque de graves lésions des yeux. Peut provoquer le cancer. Risque avéré d’effets graves pour les organes (poumon) à la suite d’expositions répétées ou d’une exposition prolongée. Le durcissement du produit génère de la chaleur. Peut provoquer de sérieuses brûlures pendant le durcissement (réhydratation) et entraîner des lésions permanentes.

US. CALIFORNIA PROPOSITION 65: WARNING: This product contains a chemical known to the State of California to cause cancer.

Firm-Fill 4010

1600 Newport Center Drive, Newport Beach, CA 92660

Canada

+ + + +

Conseil de prudence

ADDITIONAL STORAGE AND HANDLING INSTRUCTIONS Store in a dry place. Dew point conditions or other conditions causing presence of moisture may harden product during storage.

DO NOT INSTALL PRODUCT UNLESS TRAINED & LICENSED BY HACKER INDUSTRIES, INC. NEWPORT BEACH, CA

Manufactured for

US. California Proposition 65: WARNING: This product can expose you to chemicals including Crystalline Silica (Quartz), which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

Gypsum Cement Ideal for Multi-Family, Light Commercial and EN Renovation Use Danger

R ADIANT GYPSE BÉTON

SUPPLEMENTAL INFORMATION: Heat develops as product hardens. May cause serious burns during hardening (rehydration) resulting in possible permanent injury.

HACKER INDUSTRIES, INC.

Dispose of contents/container in accordance with applicable regulations.

Heat develops as product hardens. May cause serious burns during hardening (rehydration) resulting in possible permanent injury.

GYPSE DE BÉTON

FR-CA Danger Mention de danger

DISPOSAL: Dispose of contents/container in accordance with applicable regulations.

SUPPLEMENTAL INFORMATION: Heat develops as product hardens. May cause serious burns during hardening (rehydration) resulting in possible permanent injury.

Disposal

GYPSUM CONCRETE Supplemental information

D A N G E R

Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes damage to organs (lung) through prolonged or repeated exposure.

Firm-Fill

HACKER INDUSTRIES, INC. | Newport Beach, CA 92660

NET WT. 80.0 LB. (36.3 kg) GROSS WT. 80.5 LB. (36.5 kg)

Manufactured for

HACKER INDUSTRIES, INC. 1600 Newport Center Drive, Newport Beach, CA 92660 FLOOR TOPPING MIXTURE FIRE RESISTANCE CLASSIFICATION SEE UL FIRE RESISTANCE DIRECTORY 99L4 HACKER INDUSTRIES, INC. - R10474 FOR MIXING INSTRUCTIONS PLEASE REFER TO SPECIFIC DESIGN NUMBER

HACKER INDUSTRIES, INC. | Newport Beach, CA 92660

NET WT. 80.0 LB. (36.3 kg) GROSS WT. 80.5 LB. (36.5 kg)

Firm-Fill

Manufactured for

DO NOT INSTALL PRODUCT UNLESS TRAINED & LICENSED BY HACKER INDUSTRIES, INC. NEWPORT BEACH, CA

diazomethan, and aluminum (at high temperatures). Protect from moisture.

DISPOSAL: Dispose of contents/container in accordance with applicable regulations.

Firm-Fill

Contributes points to LEED® project certification

rinsing. Immediately call a poison center/doctor. If on skin: Wash with plenty of water. If skin irritation or rash occurs: Get medical advice/ attention. Take off contaminated clothing and wash before reuse.

IF exposed or concerned: Get medical advice/attention. Specific Low water demand treatment (see section 4 on the SDS).

If swallowed: Rinse mouth. Call a poison center/doctor if you feel unwell. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison center/doctor. If on skin: Wash with plenty of water. If skin irritation or rash occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. If exposed or concerned: Get medical advice/attention. Specific treatment (see section 4 on the SDS).

Storage

Store in a well-ventilated place. Keep container tightly closed. Store away from incompatible materials (see Section 10 of the SDS). Protect from moisture.

Gyp-Span

Fire-resistant

® Sound Mats and Primers Use with FIRM-FILL STORAGE: Store locked up. Store away from acids, phosphorus,

Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not breathe dust. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated work clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. After mixing with water, do not allow prolonged contact with skin until the product has completely hardened and cooled.

Response

HACKER INDUSTRIES, INC. | Newport Beach, CA 92660

NET WT. 80.0 LB. (36.3 kg) GROSS WT. 80.5 LB. (36.5 kg)

DO NOT INSTALL PRODUCT UNLESS TRAINED & LICENSED BY HACKER INDUSTRIES, INC. NEWPORT BEACH, CA

if you feel unwell. If in eyes: Rinse cautiously with water for several

Premium strength minutes. Remove contact lenses, if present and easy to do. Continue

Firm-Fill 3310 Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes damage to organs (lung) through prolonged or repeated exposure.

Precautionary statement Prevention

DO NOT INSTALL PRODUCT UNLESS TRAINED & LICENSED BY HACKER INDUSTRIES, INC. NEWPORT BEACH, CA

gloves/protective clothing/eye protection/face protection. After mixing with water, do not allow prolonged contact with skin until the

product has hardened and cooled. Gypsum Cement Ideal forcompletely Multi-Family, Light Commercial and Renovation Use RESPONSE: If swallowed: Rinse mouth. Call a poison center/doctor

GYPSE DE BÉTON

Do not breathe dust. Wash thoroughly after handling. Do not

eat, drink or smoke when using this product. Contaminated work GYPSE DE BÉTON Classic clothing must not be allowed out of the workplace. Wear protective

GYPSUM CONCRETE

PREVENTION: Obtain special instructions before use. Do not GYPSUM CONCRETE handle until all safety precautions have been read and understood.

Danger Hazard statement

DO NOT INSTALL PRODUCT UNLESS TRAINED & LICENSED BY HACKER INDUSTRIES, INC. NEWPORT BEACH, CA

IF exposed or concerned: Get medical advice/attention. Specific

STORAGE: Store locked up. Store away from acids, phosphorus, diazomethan, and aluminum (at high temperatures). Protect from moisture.

Firm-Fill 3310

RESPONSE: If swallowed: Rinse mouth. Call a poison center/doctor if you feel unwell. If in eyes: Rinse cautiously with water for several rinsing. Immediately call a poison center/doctor. If on skin: Wash with

of water. If skin irritation or rash occurs: Get medical advice/ Excellent levelingplenty attention. Take off contaminated clothing and wash before reuse.

® Sound Mats and Primers Use with FIRM-FILL treatment (see section 4 on the SDS).

DO NOT INSTALL PRODUCT UNLESS TRAINED & LICENSED BY HACKER INDUSTRIES, INC. NEWPORT BEACH, CA

Fire-rated

minutes. Remove contact lenses, if present and easy to do. Continue Sound attenuating

DO NOT INSTALL PRODUCT UNLESS TRAINED & LICENSED BY HACKER INDUSTRIES, INC. NEWPORT BEACH, CA

clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. After

+ + + +

GYPSE DE BÉTON

Do not breathe dust. Wash thoroughly after handling. Do not

mixing with water, do not allow prolonged contact with skin until the Gypsum Underlayment Ideal for Multi-Family Use product has completely hardened and cooled.

GYPSUM CONCRETE

GYPSE DE BÉTON

GYPSE DE BÉTON eat, drink or smoke when using this product. Contaminated work

Firm-Fill 2010

GYPSUM CONCRETE

PREVENTION: Obtain special instructions before use. Do not GYPSUM CONCRETE handle until all safety precautions have been read and understood.

DO NOT INSTALL PRODUCT UNLESS TRAINED & LICENSED BY HACKER INDUSTRIES, INC. NEWPORT BEACH, CA

Sound attenuating

Use with FIRM-FILL® Sound Mats and Primers

GYPSE DE BÉTON

Superior blue bag

Flattens subfloors

Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes damage to organs (lung) through prolonged or repeated exposure.

Classic

+ + + +

Firm-Fill 3310

GYPSUM CONCRETE

Gypsum Underlayment Ideal for Residential Use

Hacker+ Floor Underlayments

D A N G E R

Firm-Fill 3310

GYPSE DE BÉTON

Harmful if swallowed. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. May cause cancer. Causes damage to organs (lung) through prolonged or repeated exposure.

GYPSE DE BÉTON

GYPSUM CONCRETE

Firm-Fill 2010

GYPSUM CONCRETE

Firm-Fill

D A N G E R

Firm-Fill 3310

GYPSE DE BÉTON

GYPSUM CONCRETE

Firm-Fill 2010

GYPSE DE BÉTON

GYPSUM CONCRETE

Firm-Fill

Hacker Industries, Inc. offers a full line of eight durable Pourable Floor Underlayments to meet demanding sound-attenuating and fire-resistant specifications. With 35 years and billions of square feet of consistent installations across North America, the FIRM-FILL® product line has shown proven performance over plywood, OSB, corrugated steel deck, concrete or any structurally sound substrate.

Manufactured for

HACKER INDUSTRIES, INC. 1600 Newport Center Drive, Newport Beach, CA 92660 FLOOR TOPPING MIXTURE FIRE RESISTANCE CLASSIFICATION SEE UL FIRE RESISTANCE DIRECTORY 99L4 HACKER INDUSTRIES, INC. - R10474

HACKER INDUSTRIES, INC. | Newport Beach, CA 92660

FOR MIXING INSTRUCTIONS PLEASE REFER TO SPECIFIC DESIGN NUMBER

FIRM-FILL® Gypsum Concrete: the ORIGINAL gypsum-based floor underlayment introduced in 1983 creates a flat, durable surface with compressive strengths up to 2000 psi and excellent STC and IIC ratings, for the ultimate sound control and fire resistance in multi-family applications. FIRM-FILL® 2010+: developed specifically for use over plywood or OSB subfloors to produce the hard, smooth surface for finished floor coverings with compressive strengths of 2000-3200 psi. FIRM-FILL® 3310 Classic: a premium poured floor underlayment delivering compressive strengths from 2000 - 3300 psi. Ideal over wood or concrete subfloors in multi-family, hospitality, and renovation projects to maximize sound control and creates an enhanced surface for finished floor coverings. FIRM-FILL® 3310+: a premium, fast-setting gypsum-based floor underlayment that maximizes sound control and creates an exceptionally smooth, flat and high-strength up to 3300 psi surface, for finished floor coverings in multi-family, hospitality or renovation projects. FIRM-FILL® High Strength: a cost-efficient leveling and resurfacing gypsum-based floor underlayment for new construction or renovation projects that installs from featheredge to 3-1/2” for a fire-resistant, soundrated and crack-resistant floor surface. FIRM-FILL® 4010+: provides compressive strengths from 4000 to 5200 psi and superior bonding characteristics for cost-effective thin-capping of damaged or uneven concrete to maximize sound control and provide fire ratings in new construction or renovation projects with no shot blasting required. FIRM-FILL® CMD: a lightweight, high-strength gypsum floor underlayment for use over corrugated steeldeck in multi-family, commercial and institutional buildings, provides superior acoustical control and fire resistant properties, and compressive strengths from 3500 psi. GYP-SPAN® Radiant: a special, non-shrinking gypsum floor underlayment designed for use over radiant heating systems that provides uniform heat transfer and compressive strengths of 2000-3200 psi for a smooth, durable and warm surface ready for finished floor coverings. All Hacker Floor Underlayments are appropriate for use over Hacker Sound Mat & FIRM-FILL® SCM-125, 250, 400 and 750.

CHOOSING THE RIGHT GYPSUM UNDERLAYMENT

e yp

Commercial

Hospitality

Multi-family

ﬂo

b Su

12003300

Wood Renovation

15003300

Concrete New

25005500

Concrete Renovation

15003300

Corrugated Steel Deck

Min. 3500

Radiant Heating

20003200

Wood New

12003300

Wood Renovation

15003300

Concrete New

25005500

Concrete Renovation

15003300

Radiant Heating

20003200

Wood New

12003300

Wood Renovation

15003300

Concrete New

25005500

Concrete Renovation

15003300

Corrugated Steel Deck

Min. 3500

Radiant Heating

20003200

■ Optional

d en

o ec

Wood New

■ Recommended

PS -F

R FI

ILL

u ps

-F

R FI

ILL

+ 10

LL FI

R FI

c on

C 10

ILL

-F

R FI

sic

las

+ 10

-F

R FI

ILL

S gh

ILL

-F

R FI

n tre

+ 10

-F

R FI

ILL

N PA

i ad

-S

P GY

■ Over wood, reinforcement is required

CHOOSING THE RIGHT SOUND CONTROL MAT Hacker Industries, Inc. offers five different Sound Control Mats to meet demanding sound-attenuating reqirements for impact nose. Over 8 million of square feet of FIRM-FILL® SCM and Hacker Sound Mats have been installed in projects thorughout North America. That number is expected to double in just three years time as the demand for better IIC ratings continues to increase.

FIRM-FILL® SCM-125: a 1/8" (3mm) sound control mat, is engineered to limit impact sound transmission in multi-family construction. Ideal for when the gypsum concrete pour is not a standard thickness, FIRM-FILL® SCM-125 is topped with a minimum of 3/4" (19mm) of a FIRM-FILL® Brand Gypsum Underlayment to create an effective low profile sound control system.

FIRM-FILL® SCM-250: is a 1/4" (6mm), random filament, corrugated, "U" groove core sound control mat designed to limit impact noise between floors. When used in conjunction with a 1" FIRM-FILL® Brand Gypsum Concrete topping, the combined system has been tested to achieve a "Light Commercial" rating from the Tile Council of North America.

FIRM-FILL® SCM-400: is a 3/8" (10mm) sound mat is efficiently engineered to limit sound transmission in multifamily construction. Ideal for when the gypsum concrete pour is not a standard thickness.

FIRM-FILL® SCM-750: is a 3/4" (19mm) sound mat, that helps create sound resistant floors with the high IIC and STC level required by IBC 2009. It is a cost-effective way to address higher IIC requirements.

Hacker Sound Mat II: an innovative sound mat is composed of 92 percent recycled rubber and is designed to provide a quieter environment and meet the most demanding project specifications.

CHOOSING THE RIGHT SOUND CONTROL MAT

r loo

I-Joist

Nominal Wood

Open Web

m ste

sh ini

ing

o Flo

-F

M IR

ILL

-F

M IR

-1

ILL

-F

M IR

-2

-4

ing

sh ini

o Flo

2mm Vinyl Plank

51 IIC 53 IIC

53 IIC

7mm Laminate

53 IIC

3mm Vinyl Tile

53 IIC 53 IIC

54 IIC

3mm LVT

50 IIC

2mm Vinyl Sheet

51 IIC

54 IIC

53 IIC

3mm LVT over Hacker Sound Mat

52 IIC

3mm LVT over 5mm Encore QT4005 3mm LVT over 10mm Encore QT4010

7mm Sheet Vinyl w/ Rubber Backing

57 IIC

58 IIC

13mm Engineered Wood

57 IIC

58 IIC

2mm Vinyl Plank

50 IIC 50 IIC

52 IIC

Stone Tile

51 IIC

3mm Vinyl Tile

52 IIC 50 IIC

53 IIC

Oak Flooring

54 IIC

2mm Vinyl Sheet

53 IIC

51 IIC

53 IIC

2mm Vinyl Sheet

53 IIC

2mm Vinyl Sheet over Encore QT4005

57 IIC

2mm Vinyl Sheet

52 IIC

7mm Sheet Vinyl w/ Rubber Backing

54 IIC

56 IIC

58 IIC

13mm Engineered Wood

54 IIC

57 IIC

2mm Vinyl Plank

50 IIC 52 IIC

54 IIC

3mm Vinyl Tile

52 IIC 52 IIC

58 IIC

2mm Vinyl Sheet

53 IIC

52 IIC

54 IIC

7mm Sheet Vinyl w/ Rubber Backing

54 IIC

57 IIC

58 IIC

13mm Engineered Wood

54 IIC

57 IIC

60 IIC

c Ha

u So

53 IIC

Hacker Industries, Inc. | Architect Binder |

Hacker Industries, Inc. D I V I S I O N 03 54 13 G Y P S U M C E M E N T U N D E R L AYM E N T S

Hacker Floor Underlayments FIRM-FILL® Gypsum Concrete FIRM-FILL® 2010+ FIRM-FILL® 3310 Classic FIRM-FILL® 3310+ FIRM-FILL® High Strength FIRM-FILL® 4010+ FIRM-FILL® CMD GYP-SPAN® Radiant

FIRM-FILL® GYPSUM CONCRETE, the original “blue bag” underlayment introduced by Hacker Industries, Inc. in 1983, is designed to achieve ultimate sound and fire resistance in multifamily housing. Offering exceptional compressive strengths (up to 2000 psi), it is the versatile solution for a crack-resistant, flat and durable surface ready for finished floor coverings. • Code approvals: IAPMO ER-474, ICC-ES ER-4147, LA City RR 24540 • Specify with FIRM-FILL® SCM acoustical control mats for improved acoustical performance • Crack-resistant • Lightweight; high-strength • Superior STC and IIC ratings • Over 100 UL Fire Rated Design Listings • Meets and exceeds ASTM F2419 • Installed by trained Licensed Applicators

1 - FLOOR COVERING / 2 - FIRM-FILL® GYPSUM CONCRETE UNDERLAYMENT / 3 - FIRM-FILL® SCM OR HACK 7 - PARALLEL CHORD TRUSS / 8 - TJI ® JOIST / 9 - RESILIENT CHANNEL / 10 - GYPSUM WALLBOARD / 11 - 6”

i 00 ps 0-32 nt ® Radia 200 PAN S P GY ® 2000-3300 psi

1 - FLOOR COVERING / 2 - FIRM-FILL® GYPSUM CONCRETE UNDERLAYMENT / 3 - FIRM-FILL SCM OR HACKER i ILCON M--F6” L® 7 - PARALLEL CHORD TRUSS / 8 - TJI ® JOIST / 9 - RESILIENT CHANNEL / 10 - GYPSUM WALLBOARD FI/R11 ps

L SCM OR HACKER SOUND MAT / 4 - PLYWOOD OR OSB / 5 - NOMINAL WOOD JOIST / 6 - BATT INSULATION / BOARD / 11 - 6” CONCRETE

3310

mC onc ret e

1200200 0p FIRM s -FIL i Gypsu L®

adiant R HACKER

mi 1000 psi OR OSB / 5 - NOMINAL 0 psi 2000 psi 3000 4000 psi SOUND MAT / 4 - PLYWOOD WOOD JOIST / 6psi- BATT INSULATION / n. FIR 35 - 6” CONCRETE 0 M

Firm-Fill® 4010+

2000-3300 psi 3000-3900 psi

Firm-Fill® CMD

psi 200 0-5 ® psi 400 000 ILL to 6 M-F D® CLU up FIR 010 REE 4 -SC UE TR

psi 200 0-5 ® 400 ILL M-F FIR 010 4

Ideal for multi-family construction

Gyp-Span Radiant 1200-2000

si 0p ® 20 L 3 IL 0-F 00 psi 2500-3800 M 10+ IR 20

min. 3500 psi 2000-3200 psi

(8.3-13.8 MPa)

Not a wear

Deflection must

in (building not exceed Integral part ofsurface; 100 requires Contributes points must be fully finished floor L/360 live or ® UL design listingscovering to LEEDdead project enclosed before load installation) certification

1200-2000

1200-2000 Installed

Provides compresby Hacker strengths from sive Industries' trained Licensed psi (8.31200-2000 Applicators 13.8 MPa)

Ideal for multifamily construction

Inte UL

Provides compressive strengths from 1200-2000 psi (8.3One component 13.8 MPa) Wear

Integr UL de

Deflection must not exceed L/360 7 live or dead load

Sub pro bar

Subfloor must be protected by only of an byeffective Installed vapor barrier if sound & fire Hacker installed aboveIndustries’ control system crawl space Applicators Licensed

Requires dry-in Not a wear surface; (building must be requires finished Hacker Industries, Inc. | Architect Binder | Firm-Fill® Gypsum Concrete | © 2017 ntegral part of 100 Contributes points by covering only Installed fully enclosed floor ®

FIRM-FILL ® 3310

4000-5200 psi

Provides of for Contributes Ideal multiinIntegral part Performance compressive 100 UL fire rated points to family construction wood-frame strengths from and design listings LEED® project 1200-2000 certification structures concretepsi

Performance in and wood-frame L/360 concrete structures

00-3300 psi

0 60002psi

2000-3200 psi

P GY

Firm-Fill® High Strength

psi 000 to 6 D® CLU up REE -SC UE TR

Performance in wood-frame and concrete structures

Requires dry-

1200-2000 psi

5000 psi

1200200 0p FIRM s -FIL i Gypsu L®

D M

0 -F p 2000-3300 psi IL L ® si ® 2 ® F I M L R L Firm-Fill Gypsum Concrete 5 I C F 00 -38 3310 Firm-Fill® F IR 0 2010+ 0 Hig M-F p h S Classic I Firm-Fill® 3310 tre LL n mi ® 3310+g Firm-Fill n. FIR 35 00 MFI psi LL psi ® 25 LL ® C 00 3 FIR 80 0 Hig M-F p hS IL tre L

resrom (8.3-

1 - FLOOR COVERING / 2 - FIRM-FILL® GYPSUM CONCRETE UNDERLAYMENT / 3 - FIRM-FILL® SCM OR HACKER SOUND MAT / 4 - PLYWOOD OR OSB 00/ ps 0-32 / nt 5 - NOMINAL WOOD JOIST /6 - BATT INSULATION / 7 - PARALLEL CHORD TRUSS / 8 - TJI ® JOIST / 9 - RESILIENT CHANNEL / 10 - GYPSUM WALLBOARD ® Radia 200 AN 11 - 6” CONCRETE P S -

mC onc ret e

0 ® 20 L -3 IL 0 00 M-F 0+ IR 201

appropriate personal protective equipment

SUBMITTAL FORM TECHNICAL DATA Weight Thickness Compressive Strength Thermal Performance Fire Hazard Classification Sand

PROPERTIES 7 lb/ft² (34.2 kg/m²) at 3/4” (19 mm) 3/4” (19 mm) (minimum over wood) to 3-1/2” (89 mm) 1200 to 2200 psi (8.3 to 15.2 MPa) K-value of 2.45 BTU/(hr.ft.F°); R-value of 0.36 (ft².hr.F°) Flamespread index 0: Fuel contribution 0; Smoke density 0 1/8” (3 mm) or less washed plaster or masonry sand

ASTM C472 M F2419 C472 M C177 E84 C33

Flexural Strength

900 psi (6.21 MPa)

C348

Benefits • • • • • • • • •

Ideal for wood-frame, multi-family construction Essential for excellent STC and IIC ratings Install over a FIRM-FILL® SCM or Hacker Sound Mat for additional sound isolation Integral part of over 105 UL fire rated design listings Lightweight and crack-resistant Fast installation and rapid set time; may be walked on in 90 minutes Contributes points to LEED® project certification Creates a flat, durable surface for finished floor coverings Installed only by Licensed Applicators across North America

Product Description FIRM-FILL® Gypsum Concrete, "Super Blue" underlayment from Hacker Industries, Inc., is formulated for use over wood or concrete subfloors in multi-family construction. FIRM-FILL® Gypsum Concrete provides compressive strengths from 1200-2200 psi (8.3 - 15.2 MPa). Intallation after drywall. To keep project on schedule and on budget, Hacker Industries, Inc.’s Licensed Applicators can install over 40,000 ft² of FIRMFILL® Gypsum Concrete in one day. FIRM-FILL® Gypsum Concrete is mixed on the job site with local sand (per ASTM C33) and water to create a lightweight slurry. Installed at a minimum of 3/4” thick, the underlayment weighs approximately 7 lb/ft² (34.2 kg/m²) with a dry density range of 105-115 pcf. For new construction or renovation, FIRM-FILL® Gypsum Concrete is a cost-efficient way to create a smooth, hard surface for finished floor coverings, while offering exceptional compressive strengths matched with superior acoustical control and fire resistance properties. To achieve additional sound isolation, use in conjunction with a FIRM-FILL® SCM or Hacker Sound Mat.

Limitations • • • •

Shall not be used in exterior locations, below grade or where continuous exposure to moisture is likely. Shall not be used as a wear surface; must be covered by a finished floor covering. Structure shall be designed so that deflection does not exceed L/360 live or dead load. Certain floor coverings, such as marble, limestone, travertine and wood, may have more restrictive deflection limits. Consult the appropriate floor covering manufacturer for recommendations. • If installed above a crawl space, subfloor must be protected by a vapor barrier. • No single application of FIRM-FILL® Gypsum Concrete shall exceed 3-1/2” in depth. • FIRM-FILL® Gypsum Concrete is one component of an effective sound and fire control system. Care must be taken in the installation of all components to assure the ultimate design performance. Published acoustical and fire system tests were conducted under controlled laboratory or field conditions and reflect results applicable only to those specific assemblies.

SUBMITTAL FORM Installation Before, during and after the installation of FIRM-FILL® Gypsum Concrete, the building must be enclosed and the temperature maintained at a minimum of 50°F (10°C). Prior to the installation of FIRM-FILL® Gypsum Concrete, the subfloor shall be structurally sound (L/360), broom cleaned, dry and free from oil, grease, paraffin, laitance, wax or other contaminants. Concrete subfloors shall be 28 days or older. For on-grade applications over concrete, measure the Moisture Vapor Emission Rate (MVER) per ASTM F1869. MVER shall not exceed 3 lb/1000 ft² per 24 hours. Prime wood subfloors with Hacker Floor Primer per recommended specifications before installing underlayment. Adequate ventilation shall be provided by the General Contractor (GC) to ensure proper drying of FIRM-FILL® Gypsum Concrete. If necessary, the GC shall provide mechanical ventilation. Depending on thickness and drying conditions, the underlayment should dry within 8 to 14 days. To avoid potential problems during the drying process, the GC shall consult Hacker Industries, Inc.’s Drying Conditions Flyer and information contained on Hacker Industries, Inc.’s website for additional information concerning drying of this product. After installation, temporary wood planking shall be placed by the GC wherever the floor underlayment will be subject to wheeled or concentrated loads. Finished floor coverings can be installed when the FIRM-FILL® Gypsum Concrete is completely dry. Consult flooring contractor for recommended procedures to test for dryness and acceptable levels of moisture. Reference Hacker Industries, Inc.’s Guidelines for Installing Finished Floor Coverings. This guideline is not a warranty and shall be used as a guideline only. See ASTM F2419.

Product Data Approximate Compressive Strength per ASTM C472 Modified: Approximate Dry Density (aggregated):

1200 to 2200 psi* (8.3 to 15.2 MPa) 105 to 115 pcf

*Note: Compressive strengths published herein were achieved under controlled laboratory conditions. Actual field results may differ due to environmental conditions, regional sand variations, or inconsistent proportioning of field-applied water, sand and Hacker Floor Underlayment, as well as differences in mixing/ pumping equipment.

Compliance • ICC-ES ER-4147 • City of Los Angeles Research Report No. 24540

• FHA-HUD MR 1255 • Tile Council of North America (F180, F200, RH111, RH122)

Sound Test & UL Fire Rated Designs PURPOSE STATEMENT/DISCLAIMER These guidelines are designed to provide the architectural and building communities with detailed performance data on Hacker Industries, Inc.’s comprehensive portfolio of sound attenuation tests and UL Fire Rated Designs. The tests for the assemblies included in these guidelines were conducted in a laboratory setting per ASTM C177, E84, E90, E492 and E2179. These guidelines are not warranties and should be used as guidelines only. The architects’ and general contractors’ recommendations supersede these guidelines. Field performance may vary. Subject to express Warranty stated on Hacker Industries, Inc.’s website. Hacker Industries, Inc. regularly performs acoustical and fire (UL) testing to ensure performance standards for our products. Firm-Fill® gypsum concretes, including Firm-Fill® Gypsum Concrete, were tested acoustically with the following floor assemblies and performed as noted.

OPEN WEB

Sound System 1: No Sound Mat, 3/4” (25 mm) FIRM-FILL® Brand Gypsum Concrete

SUBMITTAL FORM

Subfloor topping: 3/4” (25 mm) FIRM-FILL® B Subfloor: 3/4” (19 mm) oriented strand board Insulation: 3-1/2” (89 mm) unfaced R-13 fiber Truss: 18” (457 mm) L/360 open web truss Ceiling isolation: Clark Dietrich RCSD resilient Ceiling: 5/8” (16 mm) type C gypsum board

FINISH

STC

Firm Fill® Gypsum Concrete – Open Web Subfloor Topping

Sound Mat

3/4” (19mm) None FIRM-FILL® Brand Gypsum Concrete

Subfloor

¹ Insulation Bare Truss Bare

3/4” (19 mm) oriented strand board

3-1/2” (89 mm) unfaced R-13 fiberglass insulation

Ceiling Isolation

Carpet and Pad

18” Clark (457 mm) Dietrich Wood Laminate ² L/360 open RCSD 2web mm Vinyl Sheet truss resilient³ channel

Ceiling

Finish

Bare¹

REPORT #

54Sound -- Report 5005002 # Rating

51 5/8” (16 mm) type C gypsum board

IIC --

STC

IIC

D6435.29 D6435.30

5005002

Bare

--51

7004018 --52 D6435.29

Carpet & Pad

--52

7554 D6435.30 7004025

Wood -52 7004018 Laminate² ¹ Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL® Brand Gypsum mm Vinyl None -54 7004025 Subfloor: 23/32” oriented strand board; 2Insulation: Sheet³ ² Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL® Brand Gypsum ¹ Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL® Brand Gypsum Concrete; Subfloor: 23/32” oriented strand board; Insulation: None Subfloor: 23/32” oriented strand board ² Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL® Brand Gypsum Concrete; Subfloor: 23/32” oriented strand board ® ® Brand Gypsum ³ Assembly varies from above inoriented the following: 1” FIRM-FILL Brand Acoust Gypsum ³ Assembly varies from above in the following: Subfloor topping: 1”Hacker FIRM-FILL Concrete; Subfloor: 23/32” strand board;Subfloor Insulation: 9”topping: (229 mm) fiberglass batt insulation Industries, Inc. Subfloor: 23/32” oriented strand board; Insulation: 9” (229 mm) fiberglass batt insulation

Sound System FIRM-FILL® SCM-125, 3/4” (19 mm) FIRM-FILL® Brand Gypsum Concret UL Fire Rated2:Designs M503, M508 Open Web L521, L528, L529, L534, L542, L546, L550, L558, L563, L574, L576, L577, L579, L583, L585, L592, M500, ® NOMINAL WOOD

Subfloor topping: 3/4” (19Gypsum mm) FIRM-FILL Brand Concrete ® B Sound System 1: No Sound Mat, 3/4” (19 mm) FIRM-FILL Subfloor isolation: 1/8” (3 mm) FIRM-FILL® SC Subfloor3/4” topping: 3/4” oriented (19 mm)strand FIRM-FILL Subfloor: (19 mm) board® Subfloor: 3-1/2” 3/4” (19 mm) oriented strand Insulation: (89 mm) unfaced R-13board fiber Insulation: 3-1/2” (89 mm)open R-13web fiberglass Truss: 18” (457 mm) L/360 truss in Joist: isolation: 9-1/4” (235 mm) 2x10 dimensional lum Ceiling Clark Dietrich RCSD resilient Ceiling5/8” isolation: Clarktype Dietrich RCSDboard resilien Ceiling: (16 mm) C gypsum Ceiling: 5/8” (16 mm) type C gypsum board

FINISH

STC

Bare

Carpet and Pad 2 mm Vinyl Sheet Carpet andClark Pad¹ 9-1/4" 5/8" Bare (16 mm) Backing 7(235 mmmm) SheetDietrich Vinyl with Rubber Carpet and

59 -D6435.01 STC IIC REPORT # 60Sound 51 Report D6435.02 # 56 -E3149.01 61Rating 53 D6435.03 57 75 E3149.02 STC IIC 58 51 D6435.04 51 -- 76E3149.01 E4054.01 56 59 57 D6435.05 57 75 E3149.02

13 mm Engineered dimensional Resilient Wood gypsum

FINISH Concrete – Nominal Wood Firm Fill® Gypsum

Subfloor Topping 3/4” (19 mm) FIRM-FILL® Brand Gypsum Concrete

Sound Mat None

Subfloor

3/4" (19 mm) oriented strand board

mm Vinyl Plank Insulation 2 Bare Truss Ceiling Isolation 3 mm Vinyl Tile 3-1/2" (89 mm) R-13 fiberglass insulation

2x10

RCSD

Ceiling

type C

Finish

Pad

IIC

REPORT #

D6435.06

Carpet and 51 76 E4054.01 lumber Channel board ¹ Assembly varies from above in the following: Subfloor topping: 1” (25 mm) FIRM-FILL® Bran Pad¹

¹Assembly varies from above in the following: Subfloor topping: 1” (25 mm) FIRM-FILL® Brand Gypsum Concrete These guidelines shall only be a resource and are not a guarantee of performance. FIRM-FILL® SCM Underlayments are only one compon acoustical performance is affected by every other component. The likelihood of achieving code compliance is contingent upon many other ULdrywall Fire Rated Designs plumbers and contractors. Developers and®general contractors are responsible for building properly ® testing field performance as so Sound System 2: FIRM-FILL SCM-125, 3/4” (19 mm) FIRM-FILL andBrand Gypsum Concre of the project. Laboratory tests are not a guarantee of field performance because of the issues noted above and many other design and/or cons Nominal Wood L006, L201, L202, L206, L208, L209, L210, L211, L212, L501, L502, L503, L504, L505,correctly L506, L507, L508, L509, L510, L511, can perform to expectation a professional acoustical consultant to assure specifications are written and that the floor/ceiling assembly ® ® , GYP-SPAN and themm) associated logos are the®re ensure L517, reliability of design to occupancy. © 2/2016 Industries, FIRM-FILL Subfloor topping: 3/4” (19 FIRM-FILL L512, L513, L514, L515, L516, L519, L520,prior L522, L523, L525, L526, Hacker L532, L533, L535Inc. , L536, L537, L540, L541, L545,

L557, L569, L588, L590, L593, L598, M504, M517, M519, M530, M531, M517

Subfloor isolation: 1/8” (3 mm) FIRM-FILL® S Subfloor: 3/4” (19 mm) oriented strand board 5 3-1/2” (89 mm) R-13 fiberglass in Insulation: Joist: 9-1/4” (235 mm) 2x10 dimensional lum Ceiling isolation: Clark Dietrich RCSD resilien Ceiling: 5/8” (16 mm) type C gypsum board Hacker Industries, Inc. | Architect Binder | Firm-Fill® Gypsum Concrete | © 2017

SUBMITTAL FORM

Firm Fill® Gypsum Concrete – I-Joist Subfloor Topping 1” (25 mm) FIRM-FILL® Brand Gypsum Concrete

Sound Mat 1/4" (6 mm) FIRM-FILL® SCM-250 Sound Control Mat

Subfloor

3/4” (19 mm) oriented strand board

Insulation

3-1/2” (89 mm) unfaced R-11 fiberglass insulation

Joist

Ceiling Isolation

12” (302 mm) Weyerhaeuser Tus Joist® TJI® Joist

Clark Dietrich RCSD resilient channel

Ceiling

5/8” (16 mm) type C gypsum board

Finish

Sound Rating

Report #

STC

IIC

Bare

E7891.01

2 mm Vinyl Plank

621

E7891.02

3 mm Vinyl Tile

E7891.03

2 mm Vinyl Sheet

E7891.04

7 mm Sheet Vinyl with Rubber Backing

E7893.05

¹ Assembly differs from above in the following: Ceiling: 2 layers 5/8" (16 mm) type X gypsum board

UL Fire Rated Designs I-Joist L518, L530, L538, L547, L556, L570, L571, L581, L583, L589, M502, M506, M512

Firm Fill® Gypsum Concrete – Concrete Assembly Subfloor Topping 3/4” (19 mm) FIRM-FILL® Brand Gypsum Concrete

Sound Mat None

Subfloor

3/4" (19 mm) oriented strand board

Insulation

3-1/2" (89 mm) R-13 fiberglass insulation

Truss

9-1/4" (235 mm) 2x10 dimensional lumber

Ceiling Isolation Clark Dietrich RCSD Resilient Channel

Ceiling

5/8" (16 mm) type C gypsum board

Finish

Sound Rating

Report #

STC

IIC

Bare

E3149.01

Carpet and Pad

E3149.02

Carpet and Pad¹

E4054.01

¹Assembly varies from above in the following: Subfloor topping: 1” (25 mm) FIRM-FILL® Brand Gypsum Concrete

UL Fire Rated Designs Concrete J917, J919, J920, J924, J927, J931, J957, J991, J994

SUBMITTAL FORM Related Products FIRM-FILL® SCM sound control mats, Hacker Floor Primer, Hacker TopCoat™ SP and Hacker Floor Sealer are available for use with FIRM-FILL® Gypsum Concrete Floor Underlayment. Contact Hacker Industries, Inc. at (800) 642-3455 or info@hackerindustries.com for more information.

Warranty Subject to express warranty stated on Hacker Industries, Inc.’s website.

Submittal Approvals Project Name Contractor/Architect Signature Date

PRODUCT INFORMATION See www.HackerIndustries.com for current recommended product specifications and literature. WARNING When mixed with water, this product hardens and becomes extremely hot. DO NOT attempt to make a cast enclosing any part of the body using this material. Failure to follow these instructions may cause severe burns that may require surgical removal of affected tissue or amputation of limb. Portland cement is strongly alkaline. Direct contact can be corrosive and cause severe damage or chemical burns to eyes and wet, moist skin. Avoid contact with eyes and skin. Wear protective glasses and clothing. If eye contact occurs, immediately flush thoroughly with water for 30 minutes and seek medical advice. Inhalation of dust may be corrosive or cause chemical burns or irritation to nose, throat and respiratory tract. Avoid breathing dust. Use a NIOSH/MSHA-approved dust respirator. Wash thoroughly with soap and water after use. Do not ingest. If ingested, call a physician. Product safety, call (800) 642-3455. KEEP OUT OF REACH OF CHILDREN.

TRADEMARKS FIRM-FILL®, GYP-SPAN®, Let Our Products Floor You™ and the associated logos are trademarks of Hacker Industries, Inc. LEED® is a registered trademark of the U.S. Green Building Council. WARRANTY HACKER INDUSTRIES, INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, DIRECTLY OR INDIRECTLY SUSTAINED, NOR FOR ANY LOSS CAUSED BY APPLICATION OF THESE GOODS NOT IN ACCORDANCE WITH CURRENT PRINTED INSTRUCTION OR FOR OTHER THAN THE INTENDED USE. OUR LIABILITY IS EXPRESSLY LIMITED TO REPLACEMENT OF DEFECTIVE GOODS. ANY CLAIM SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING TO US WITHIN 30 DAYS FROM DATE IT WAS, OR REASONABLY SHOULD HAVE BEEN, DISCOVERED. SAFETY FIRST Follow good safety/industrial hygiene practices during installation. Wear appropriate personal protective equipment. Read specs, MSDS and literature prior to specification and installation. © 2017 Hacker Industries, Inc., Newport Beach, CA.

RECOMMENDED SPECIFICATIONS PART I: GENERAL 1.1

Scope

Specify to meet project requirements. The conditions of the Contract (General, Supplementary, and other conditions) and the General Requirements (Sections of Division 1) govern the provisions of this section. 1.2

Qualifications

Supplier: Hacker Industries, Inc., Newport Beach, California

Installer: Installation of FIRM-FILL® Gypsum Concrete shall be by a trained Licensed Applicator of Hacker Industries, Inc., using mixing and pumping equipment with a water meter approved by Hacker Industries, Inc.

All materials specified herein shall be approved by Hacker Industries, Inc., Newport Beach, CA. All others shall receive prior approval.

Compressive strength shall be specified from 1200 to 2200 psi (8.3 to 15.2 MPa).

Materials shall be delivered in their original, unopened packages and protected from exposure to the elements before and after delivery. Do not allow bags to get wet. Product shall not be used beyond shelf life.

Certification: Upon completion of this portion of the work and upon request, and as a condition of its acceptance, deliver to the architect a certificate from the Licensed Applicator, stating that the material used in this work complies with the specified requirements.

PART II: PRODUCTS 2.1

Materials

Gypsum Concrete: FIRM-FILL® Gypsum Concrete, as supplied by Hacker Industries, Inc.

Subfloor Primer: Hacker Floor Primer or approved equal

Sand: 1/8” (3 mm) or less washed plaster or masonry sand

Water: Potable and free from impurities

Sealer: Hacker TopCoat™ SP (if specified)

2.2

Mix Designs: See section 3.3

PART III: PREPARATION 3.1

Condition of Subfloor

Subfloor shall be structurally sound (L/360), broom cleaned, dry and free from oil, grease, paraffin, laitance, wax or other contaminants before the arrival of the Hacker Licensed Applicator.

Before installation, the General Contractor (GC) shall inspect and approve the condition of the subfloor and test the existing subfloor for moisture.

RECOMMENDED SPECIFICATIONS (CONT.)

3.2

Preparation of Subfloor

Leak Prevention: All cracks and voids shall be filled with a quick-setting patching or taping compound, or equal, where leakage may occur.

Prime wood subfloors with one coat of Hacker Floor Primer (diluted 1:4 with water) using one gallon (3.78 L) per 500 ft2 (47 m2).

Hacker Floor Primer recommended over concrete substrates. The Hacker Licensed Applicator can give specific recommendations.

3.3

Mixing Instructions

Add 80-pound (36.3 kg) bag of FIRM-FILL® Gypsum Concrete to 6 to 7 gallons (22.7 to 26.5 L) of water followed by the specific sand ratio. Do not overwater. Water amount will vary with the wetness of the sand.

This is the proper sequence for mixing of FIRM-FILL® Gypsum Concrete.

First add water to bucket followed by FIRM-FILL® Gypsum Concrete and finally the sand.

3.4

Underlayment Application

Scheduling:

1. Installation of FIRM-FILL® Gypsum Concrete shall not begin until the building is enclosed, including roof, windows, doors and other openings.

2. In the absence of Sound Mat, FIRM-FILL® Gypsum Concrete may be installed before or after the installation of drywall.

Application:

1. The minimum thickness of FIRM-FILL® Gypsum Concrete varies with the type of subfloor. Over wood subfloors, a minimum of 3/4” (19 mm) is required. Over precast or poured-inplace concrete, a minimum of 1/2” (13 mm) is required.

2. Install FIRM-FILL® Gypsum Concrete at specified thickness by placing contents of bags, sand and water into the approved high-speed mixing device and blending for a minimum of one minute. FIRM-FILL® Gypsum Concrete shall be pumped onto floor areas, spreading and screeding to a smooth surface. Place as continuously as possible until installation is complete so that no FIRM-FILL® Gypsum Concrete slurry is placed against FIRM-FILL® Gypsum Concrete that has obtained its initial set, except at authorized joints.

3. FIRM-FILL® Gypsum Concrete is suitable for interior applications only and shall be covered by a finished floor covering.

Protection: After installation, temporary wood planking shall be placed by the GC wherever the floor underlayment will be subject to wheeled or concentrated loads. The GC shall not place concentrated loads—such as pallets of material, drywall, taping compounds or any heavy items which may cause deflection—in the middle of the floor or in hallways.

RECOMMENDED SPECIFICATIONS (CONT.)

Drying: Before, during and after installation of FIRM-FILL® Gypsum Concrete, building interior shall be ventilated and heated to a minimum of 50°F (10°C) to ensure completion of the drying process. The GC shall provide continuous ventilation and adequate heat to rapidly remove moisture from the area until the FIRM-FILL® Gypsum Concrete is dry. If necessary, the GC shall provide mechanical ventilation. Do not install finished floor coverings until the FIRM-FILL® Gypsum Concrete has been tested for dryness. Consult flooring contractor for recommended procedures to test for dryness and acceptable levels of moisture. To avoid potential problems during the drying process, the GC shall consult Hacker Industries, Inc.’s Drying Conditions Flyer and information contained on Hacker Industries, Inc.’s website for additional information concerning drying of this product.

3.5

Preparation for Installation of Floor Coverings

Sealing: Any areas where the underlayment surface has been damaged shall be cleaned and sealed regardless of floor covering specified. Floor covering manufacturers’ specifications and requirements supersede these recommendations.

Floor Covering Procedures: Please see Hacker Industries, Inc.’s Guidelines for Installing Finished Floor Coverings. The document is not a warranty and shall be used as a guideline only. See also ASTM F2419 for recommended procedures.

3.6

Field Quality Control

Slump Test: FIRM-FILL® Gypsum Concrete shall be tested for slump at the beginning of each installation in order to establish the required slump. Slump tests shall then be taken periodically during installation to verify that the required slump is maintained. Slump tests shall be conducted on an approved plexiglass surface using a 2” by 4” (51 mm by 102 mm) cylinder. The acceptable patty size shall be 9” (228 mm) plus or minus 1/2” (13 mm) in diameter.

Field Samples: Testing shall be done in accordance with ASTM C472 modified testing procedures using split brass molds. Prior to independent testing, consult Hacker Industries, Inc. for proper ASTM procedures

Warranty: Subject to express warranty stated on Hacker Industries, Inc.’s website.

PROJECT REFERENCES FIRM-FILL® Gypsum Concrete, "Super Blue" underlayment introduced by Hacker Industries, Inc. in 1983 and since improved with new technology, is designed to achieve the ultimate sound control and fire resistance in multi-family housing. With over 105 UL fire rated design listings and exceptional STC and IIC ratings, FIRMFILL® Gypsum Concrete is an excellent choice for jobs needing compressive strengths up to 2200 psi. Below is a small sample of projects that have utilized FIRM-FILL® Gypsum Concrete.

Contractor: Adolfson & Peterson Project: Campus Suites on the Rail, Coyote Landing Location: Phoenix, Arizona / Tempe, Arizona Description: Various projects with FIRM-FILL® Gypsum Concrete Contractor: A G Spanos Project: Delayne at Twin Creek Location: Allen, Texas Description: 139,220 ft² of FIRM-FILL® Gypsum Concrete Contractor: Amli Project: Quadrangle Location: Dallas, Texas Description: 148,365 ft² of FIRM-FILL® Gypsum Concrete Contractor: Camden Construction Project: The Park at Crown Valley Location: Mission Viejo, California Description: 150,000 ft² of FIRM-FILL® Gypsum Concrete Contractor: Colson and Colson Project: Grassland Estates Location: Wichita, Kansas Description: 47,000 ft² of FIRM-FILL® Gypsum Concrete Contractor: Connery Building Corporation Project: Harbor House U.S. Housing & Urban Development (HUD) Apartments Location: Madison, Wisconsin Description: 200,000 ft² of FIRM-FILL® Gypsum Concrete Contractor: Fairfield Development, LP Project: Indigo Creek Location: Thornton, Colorado Description: 140,040 ft² of FIRM-FILL® Gypsum Concrete Contractor: Fairfield Development, LP Project: Los Flores Apartments Location: Rancho Santa Margarita, California Description: 329,584 ft² of FIRM-FILL® Gypsum Concrete

FIRM-FILL® 2010+ is Hacker Industries, Inc.’s underlayment solution over plywood or OSB subfloors in apartments, condos, hotels and motels. FIRM-FILL® 2010+ produces the hardest, smoothest surface for finished floor coverings in the industry. This new formulation has compressive strengths from 2000-3200 psi. FIRM-FILL® 2010+ also stiffens subfloors and eliminates nail squeaks and pops. Superior self-healing characteristics provide a durable, flat, non-structural surface. • Specify with Firm-Fill® SCM acoustical control mats for improved acoustical performance • Over 100 UL Fire Rated Design Listings; ICC-ES Report • Rapid, efficient installation; mixes quickly; easy to finish • Incredible surface hardness three hours after pouring • Billions of square feet of Hacker Floor Underlayments installed nationwide • Installed by trained Licensed Applicators

1 - FLOOR COVERING / 2 - FIRM-FILL® 2010+ GYPSUM CONCRETE UNDERLAYMENT / 3 - FIRM-FILL® SCM O 6 - BATT INSULATION / 7 - PARALLEL CHORD TRUSS / 8 - TJI ® JOIST / 9 - RESILIENT CHANNEL / 10 - GYPSU

i 00 ps 0-32 nt ® Radia 200 PAN S P 1 - FLOOR COVERING / 2 - FIRM-FILL CON GY ® 2010+ GYPSUM 2000-3300 psi 6 - BATT INSULATION / 7 - PARALLEL CHORD TRUSS / 8 - TJ i FIRM-FILL ® ps 00 ® 3310 2 L 3 IL 000 M-F 0+ IR 201

- FIRM-FILL® SCM OR HACKER SOUND MAT / 4 - PLYWOOD OR OSB / 5 - NOMINAL WOOD JOIST / ANNEL / 10 - GYPSUM WALLBOARD / 11 - 6” CONCRETE

nt ® Radia AN

1200200 0p FIRM s -FIL i Gypsu L®

i 00 ps

LL / 4 i- PLYWOOD OR OSB / 5 - NOMINAL WOOD JOIST / M-FILL® SCM0OR HACKER SOUND MAT ® psi 1000 2000 psi 3000 psi 25 ILL ® IRM-Fpsi C 00/ 11 - 6” CONCRETE L / 10 - F GYPSUM WALLBOARD -3

FIR 80 0 Hig M-F p hS IL t L r e Firm-Fill® Gypsum Concrete si

Firm-Fill® 3310+ mi

35 RM Strength Firm-Fill® IHigh 00 FI LL psi ® C

UL for 1 to 2 hour fire ratings

6000 psi

4000-5200 psi min. 3500 psi

3000-3900 psi

Gyp-Span Radiant

2000-3200 psi

2500-3800 psi

True-Screed CLU

up to 6000 psi

Ideal for plywood or OSB multi-family construction

UL design listings for 1 to 2 hour fire ratings Requires dryin (building must be fully enclosed before design listings installation)

5000 psi

2000-3200

psi 200 0-5 ® 400 ILL M-F FIR 010 4

Performance over concrete slabs or precast concrete

Firm-Fill® CMD

psi 000 to 6 D® CLU up REE -SC UE TR

200

esrom

en g

Firm-Fill® 4010+

2000-3200 psi

25 00 FIR -380 0 Hig M-F p hS IL tr L

D M

2000-3300 psi FIRM-FILL ® 3310

0 mpress from si a)

1200-2000 psi

psi 200 0-5 ® 400 ILL M-F FIR 010 4

adiant

Firm-Fill® 2010+

psi 000 to 6 D® CLU up REE -SC UE TR

4000 psi

D M

3310

mC onc ret e

mi / 2 - FIRM-FILL® 2010+ CONCRETE UNDERLAYMENT / 3 - FIRM-FILL® SCM OR HACKER SOUND MAT / 4 - PLYWOOD OR OSB / 1 - FLOOR COVERING n. FIR 35 / 6 - BATT INSULATION / 7 - PARALLEL CHORD TRUSS / 8 - TJI ® JOIST / 9 - RESILIENT CHANNEL / 10 - GYPSUM WALLBOARD / 5 - NOMINAL WOOD JOIST 00 Mps-i 6” CONCRETE FI p 2000-330011

plywood or & Provides over Performance Provides UL designIdeal listingsforFast installation Installedcompresby compressive for 1 to 2OSB hour multi-family rapid set; walk on sive Hacker Industries’ from slabs or strengths concrete strengths from in 90 minutes trained Licensed construction psi concrete fire ratings precast 2000-3200 2000-3200 psi Applicators (13.8-22 MPa) (13.8-22 MPa)

Fast installation & rapid set; walk on in 90 minutes L/360

Installed only by Performance over Hacker Industries’ concrete slabs or Licensed Applicatorsprecast concrete

Not a wear Deflection must Subfloor must surface; requires not exceed L/360 be protected by finished floor live or dead load vapor barrier if covering installed by onlyabove installation & Fast Installed crawl space

One component of an effective sound & fire control system

UL for rat

Ideal for plywoo OSB multi-family construction

Wear appropriate personal protective equipment

on rapid set; walk Hacker Requires dry-in Industries’ Not a wear surface; Deflection must Applicators in 90 minutes(building Licensed must be requires finished not exceed L/360 fully enclosed floor covering live2010+ or dead load Hacker Industries, Inc. | Architect Binder | Firm-Fill® | © 2017 before installation)

Su pro ba ab

SUBMITTAL FORM TECHNICAL DATA Weight Thickness Compressive Strength Thermal Performance Fire Hazard Classification Sand Flexural Strength

PROPERTIES 7.2 lb/ft² (35.2 kg/m²) at 3/4” (19 mm) 3/4” (19 mm) (minimum over wood) to 3-1/2” (89 mm) 2000 to 3200 psi (13.8 to 22 MPa) K-value of 2.45 BTU/(hr.ft.F°); R-value of 0.36 (ft².hr.F°) Flamespread index 0: Fuel contribution 0; Smoke density 0 1/8” (3 mm) or less washed plaster or masonry sand 1100 psi (7.58 MPa)

ASTM C472 M F2419 C472 M C177 E84 C33 C348

Benefits • • • • • • • • • •

Reformulated for modern floor coverings Ideal for wood-frame, multi-family construction Contributes to excellent STC and IIC ratings Install over a FIRM-FILL® SCM or Hacker Sound Mat for additional sound isolation Ideal underlayment for use over concrete slabs or precast concrete UL fire rated designs for 1 to 2 hour fire ratings Lightweight and crack-resistant Fast installation and rapid set time; may be walked on in 90 minutes Creates a flat, durable, non-structural underlayment surface for finished floor coverings Installed only by trained Licensed Applicators across North America

Product Description FIRM-FILL® 2010+ is designed for use over wood or concrete subfloors. It stiffens the subfloor to eliminate squeaks and nail pops. With additional surface hardness, FIRM-FILL® 2010+ provides compressive strengths from 2000 to 3200 psi (13.8 to 22 MPa). Depending on the compressive strength, it may be installed before or after drywall. To keep project on schedule and on budget, Licensed Applicators may install over 25,000 ft² of FIRM-FILL® 2010+ in one day. FIRM-FILL® 2010+ is mixed on the job site with local sand (per ASTM C33) and water to create a lightweight slurry. Installed at a minimum of 3/4” thick, the underlayment weighs approximately 7.2 lb/ft² (35.2 kg/m²) with a dry density range of 105-115 pcf. For new construction, FIRM-FILL® 2010+ is a cost-effective way to create a smooth, hard surface for finished floor coverings while offering exceptional compressive strengths matched with superior acoustical control and fire resistance properties. To achieve additional sound isolation, use FIRM-FILL® 2010+ with either a FIRM-FILL® SCM sound control mat or Hacker Sound Mat.

Limitations • Do not use FIRM-FILL® 2010+ in exterior locations, below grade or where continuous exposure to moisture is likely. • Shall not be used as a wear surface; must be covered by a finished floor covering. • Structure shall be designed so that deflection does not exceed L/360 live or dead load. Certain floor coverings such as marble, limestone, travertine and wood may have more restrictive deflection limits. • If installed above a crawl space, subfloor must be protected by a vapor barrier. • No single application of FIRM-FILL® 2010+ shall exceed 3” in depth. • FIRM-FILL® 2010+ is one component of an effective sound and fire control system. Care must be taken in the installation of all components to assure the ultimate design performance. Published acoustical and fire system tests were conducted under controlled laboratory or field conditions and reflect results applicable only to those specific assemblies. Hacker Industries, Inc. | Architect Binder | Firm-Fill® 2010+ | © 2017

SUBMITTAL FORM Installation Before, during and after the installation of FIRM-FILL® 2010+, the building must be enclosed and the temperature maintained at a minimum of 50°F (10°C). Prior to the installation of FIRM-FILL® 2010+, the subfloor shall be structurally sound (L/360), broom cleaned, dry and free from oil, grease, paraffin, laitance, wax or other contaminants. Concrete subfloors shall be 28 days or older. For on-grade applications over concrete, measure the Moisture Vapor Emission Rate (MVER) per ASTM F1869. MVER shall not exceed 3 lb/1000 ft² per 24 hours. Prime wood subfloors with Hacker Floor Primer per recommended specifications before installing underlayment. Adequate ventilation shall be provided by the General Contractor (GC) to ensure proper drying of FIRMFILL® 2010+. If necessary, the GC shall provide mechanical ventilation. Depending on thickness and drying conditions, the underlayment should dry within 8 to 14 days. To avoid potential problems during the drying process, the GC shall consult Hacker Industries, Inc.’s Drying Conditions Flyer and information contained on Hacker Industries, Inc.’s website for additional information concerning drying of this product. After installation, temporary wood planking shall be placed by the GC wherever the floor underlayment will be subject to wheeled or concentrated loads. Finished floor coverings can be installed when the FIRM-FILL® 2010+ is completely dry. Consult flooring contractor for recommended procedures to test for dryness and acceptable levels of moisture. Reference Hacker Industries, Inc.’s Guidelines for Installing Finished Floor Coverings. This guideline is not a warranty and shall be used as a guideline only. See ASTM F2419.

Product Data Approximate Compressive Strength per ASTM C472 Modified: Approximate Dry Density (aggregated):

2000 to 3200 psi* (13.8 to 22 MPa) 105 to 115 pcf

Compliance • ICC-ES ER-4147 • City of Los Angeles Research Report No. 24540

• FHA-HUD MR 1255 • Tile Council of North America (F180, F200, RH111, RH122)

Sound Test & UL Fire Rated Designs PURPOSE STATEMENT/DISCLAIMER These guidelines are designed to provide the architectural and building communities with detailed performance data on Hacker Industries, Inc.’s comprehensive portfolio of sound attenuation tests and UL Fire Rated Designs. The tests for the assemblies included in these guidelines were conducted in a laboratory setting per ASTM C177, E84, E90, E492 and E2179. These guidelines are not warranties and should be used as guidelines only. The architects’ and general contractors’ recommendations supersede these guidelines. Field performance may vary. Subject to express Warranty stated on Hacker Industries, Inc.’s website. Hacker Industries, Inc. regularly performs acoustical and fire (UL) testing to ensure performance standards for our products. Firm Fill® gypsum concretes, including Firm Fill® 2010+, were tested acoustically with the following floor assemblies and performed as noted.

OPEN WEB

Sound System 1: No Sound Mat, 3/4” (25 mm) FIRM-FILL® Brand Gypsum Concrete

SUBMITTAL FORM

Subfloor Topping

Sound Mat

3/4” None (25mm) FIRM-FILL® Brand Gypsum Concrete

FINISH Firm Fill® 2010+ – Open Web ¹ Subfloor InsulationBareTruss Ceiling Ceiling Isolation Bare 3/4” (19 mm) oriented strand board

Carpet and Pad 3-1/2” 18” (457 Clark ² (89 mm) Wood mm) Laminate L/360 Dietrich unfaced open web RCSD 2truss mm Vinyl Sheet ³ R-13 resilient fiberglass channel insulation

5/8” (16 mm) type C gypsum board

STC Finish

Bare¹ Bare Carpet and Pad

IIC

54Sound-51Rating--

REPORT # 5005002 Report #D6435.29

STC 52

IIC 75

5005002

D6435.29

D6435.30

---

D6435.30 7004018

7004025

Wood Subfloor Laminate² topping: -- 1”52FIRM-FILL 7004018 ® ¹ Assembly varies from above in the following: Brand Gypsum Subfloor: 23/32” oriented strand board; Insulation: 2 mm Vinyl None -54 7004025 Sheet³Subfloor topping: 1” FIRM-FILL® Brand Gypsum ² Assembly varies from above in the following: ¹ Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL®Subfloor: Brand Gypsum23/32” Concrete; Subfloor: 23/32” orientedboard strand board; Insulation: None oriented strand ² Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL® Brand Gypsum Concrete; Subfloor: 23/32” oriented strand board ³ Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL® Brand Acoust Gypsum Hacker Industries, Inc. ³ Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL Concrete; Subfloor: 23/32” oriented strand board; Insulation: 9” (229 mm) fiberglass batt insulation ® Brand Gypsum Subfloor: 23/32” oriented strand board; Insulation: 9” (229 mm) fiberglass batt insulation

UL Fire Rated Designs Sound System 2: FIRM-FILL® SCM-125, 3/4” (19 mm) FIRM-FILL® Brand Gypsum Concret

NOMINAL WOOD

Open Web L521, L528, L529, L534, L542, L546, L550, L558, L563, L574, L576, L577, L579, L583, L585, L592, M500, M503, M508 ® Subfloor topping:®3/4” (19Gypsum mm) FIRM-FILL Brand Concrete B Sound System 1: No Sound Mat, 3/4” (19 mm) FIRM-FILL ® Subfloor isolation: 1/8” (3 mm) FIRM-FILL SC Subfloor: (19 mm) board® Subfloor3/4” topping: 3/4” oriented (19 mm)strand FIRM-FILL Insulation: (89 mm) unfaced R-13board fiber Subfloor: 3-1/2” 3/4” (19 mm) oriented strand Truss: 18” (457 mm) L/360 truss in Insulation: 3-1/2” (89 mm)open R-13web fiberglass Ceiling Clark Dietrich RCSD resilient Joist: isolation: 9-1/4” (235 mm) 2x10 dimensional lum Ceiling: (16 mm) C gypsum Ceiling5/8” isolation: Clarktype Dietrich RCSDboard resilien Ceiling: 5/8” (16 mm) type C gypsum board FINISH

Subfloor Topping

Sound Mat

3/4” (19 None mm) FIRM-FILL® Brand Gypsum Concrete

Nominal Wood

STC

IIC

REPORT #

Bare 59 -D6435.01 STC IIC REPORT # FirmFINISH Fill® 2010+ – Nominal Wood 2 mm Vinyl Plank 60 51 D6435.02 56Sound-- Report E3149.01 Subfloor Insulation Bare Truss Ceiling Ceiling Finish 3 mm Vinyl TileIsolation 61 Rating 53 D6435.03 # Carpet and Pad 57 75 E3149.02 2 mm Vinyl Sheet 58STC IIC 51 D6435.04 Carpet and Pad¹ 51 76 E4054.01 Bare -E3149.01 3/4" (19 3-1/2" Clarkwith Rubber 5/8" (16 7 9-1/4" mm Sheet Vinyl Backing 5956 57 D6435.05 mm) (89 mm) (235 mm) Dietrich mm) Carpet and 57 75 E3149.02 oriented R-13 RCSD Woodtype C 132x10 mm Engineered 59 57 D6435.06 Pad strand fiberglass Resilient gypsum CarpetSubfloor and 51 1” 76(25E4054.01 from above in the following: topping: mm) FIRM-FILL® Bran board insulation ¹ Assembly varies Channel board Pad¹

These guidelines shall only be a resource and are not a guarantee of performance. FIRM-FILL® SCM Underlayments are only one compon acoustical performance is affected by every other component. The likelihood of achieving code compliance is contingent upon many other plumbers and drywall contractors. Developers and®general contractors are responsible for building properly ® and testing field performance as so UL Laboratory FireSystem Rated Designs Sound 2: FIRM-FILL SCM-125, (19 mm) Gypsum Concre of the project. tests are not a guarantee of field performance3/4” because of the issuesFIRM-FILL noted above andBrand many other design and/or cons a professional acoustical consultant assureL501, specifications written correctly and that the floor/ceiling assembly can perform to expectation L006, L201, L202, L206, L208, L209, L210, L211, toL212, L502,are L503, L504, L505, L506, L507, L508, L509, ® ® , GYP-SPAN associated logos are the®re ensure reliability of design prior to occupancy. © 2/2016 Hacker Industries, Inc. FIRM-FILL Subfloor topping: 3/4” and (19themm) FIRM-FILL

L510, L511, L512, L513, L514, L515, L516, L517, L519, L520, L522, L523, L525, L526, L532, L533, L535 , L536, L537, L540, L541, L545, L557, L569, L588, L590, L593, L598, M504, M517,Subfloor M519, M530, M531, M517 isolation: 1/8” (3 mm) FIRM-FILL® S

I-Joist L518, L530, L538, L547, L556, L570, L581, L589, M502, M506, M512

Subfloor: 3/4” (19 mm) oriented strand board 5 Insulation: 3-1/2” (89 mm) R-13 fiberglass in Joist: 9-1/4” (235 mm) 2x10 dimensional lum Ceiling isolation: Clark Dietrich RCSD resilien Ceiling: 5/8” (16 mm) type C gypsum board 21

SUBMITTAL FORM

Firm Fill® 2010+ – Concrete Assembly Subfloor Topping 1-1/4” (32 mm) FIRM-FILL® Brand Gypsum Concrete

Sound Mat

Subfloor

3/8" 6" (10 mm) (152 mm) FIRM-FILL® concrete SCM-400 Sound Control Mat

Insulation

None

Truss

None

Ceiling Isolation None

Ceiling

None

Finish

Sound Rating

Report #

STC

IIC

Bare

5014051

Bare

7014063

Sheet Vinyl

7014064

Bare

Δ 7014091 23*

*Tested in accordance with ASTM E2179 - Standard Test Method for Laboratory Measurement of Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors.

UL Fire Rated Designs Concrete J917, J919, J920, J924, J927, J931, J957, J991, J994

Related Products 30

OPEN WEB

Sound System 1: No Sound Mat, 3/4” (25 mm) FIRM-FILL® Brand Gypsum Concrete

SUBMITTAL FORM

Subfloor Topping

Sound Mat

3/4” None (25mm) FIRM-FILL® Brand Gypsum Concrete

Subfloor

3/4” (19 mm) oriented strand board

FINISH Firm Fill® 3310+ – Open Web ¹ InsulationBareTruss Ceiling Ceiling Isolation Bare Carpet and Pad 3-1/2” Clark 18” (89 mm) Wood (457Laminate mm) Dietrich ² unfaced RCSD L/360 2 open mm Vinyl ³ R-13 resilient webSheet fiberglass truss channel insulation

5/8” (16 mm) type C gypsum board

STC Finish

Bare¹

IIC

REPORT #

54 Sound -Rating 51 -STC IIC 52 75

5005002 Report # D6435.29

D6435.30

5005002

Bare

52 7004018 -D6435.29

Carpet and Pad

75 54

D6435.30 7004025

7004018

Wood Laminate²

® 2 mmSubfloor Vinyl -- 1”54 7004025 ¹ Assembly varies from above in the following: topping: FIRM-FILL Brand Gypsum Sheet³ Subfloor: 23/32” oriented strand board; Insulation: None ® ® Brand ¹ Assembly varies from above in the following: Subfloor topping: 1”²FIRM-FILL Gypsum Concrete; oriented strand board; Insulation: None Assembly varies from aboveSubfloor: in the 23/32” following: Subfloor topping: 1” FIRM-FILL Brand Gypsum ² Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL® Brand Gypsum Concrete; Subfloor: 23/32” oriented strand board Subfloor: 23/32” oriented strand board ® ³ Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL Brand Gypsum Concrete; Subfloor: 23/32” oriented strand board; Insulation: 9” (229 mm) fiberglass batt insulation ³ Assembly varies from above in the following: Subfloor topping: 1” FIRM-FILL® Brand Acoust Gypsum Hacker Industries, Inc. Subfloor: 23/32” oriented strand board; Insulation: 9” (229 mm) fiberglass batt insulation

NOMINAL WOOD

UL Fire Rated Designs Sound System 2: FIRM-FILL® SCM-125, 3/4” (19 mm) FIRM-FILL® Brand Gypsum Concret Open Web L521, L528, L529, L534, L542, L546, L550, L558, L563, L574, L576, L577, L579, L583, L585, L592, M500, M503, M508 ® Subfloor topping:®3/4” (19Gypsum mm) FIRM-FILL Brand Concrete B Sound System 1: No Sound Mat, 3/4” (19 mm) FIRM-FILL ® Subfloor isolation: 1/8” (3 mm) FIRM-FILL SC Subfloor: (19 mm) board® Subfloor3/4” topping: 3/4” oriented (19 mm)strand FIRM-FILL Insulation: (89 mm) unfaced R-13board fiber Subfloor: 3-1/2” 3/4” (19 mm) oriented strand Truss: 18” (457 mm) L/360 truss in Insulation: 3-1/2” (89 mm)open R-13web fiberglass Ceiling Clark Dietrich RCSD resilient Joist: isolation: 9-1/4” (235 mm) 2x10 dimensional lum Ceiling: (16 mm) C gypsum Ceiling5/8” isolation: Clarktype Dietrich RCSDboard resilien Ceiling: 5/8” (16 mm) type C gypsum board FINISH

Subfloor Topping

Sound Mat

3/4” None (19 mm) FIRM-FILL® Brand Gypsum Concrete

Nominal Wood

STC

IIC

REPORT #

Bare 59 -D6435.01 STC IIC REPORT # FirmFINISH Fill® 3310+ – Nominal Wood 2 mm Vinyl Plank 60 51 D6435.02 56Sound-- Report E3149.01 Subfloor Insulation Bare Truss Ceiling Ceiling Finish 3 mm Vinyl TileIsolation 61 Rating 53 D6435.03 # Carpet and Pad 57 75 E3149.02 2 mm Vinyl Sheet 58STC IIC 51 D6435.04 Carpet and Pad¹ 51 76 E4054.01 Bare -E3149.01 3/4" 3-1/2" Clarkwith Rubber 5/8" Backing 7 9-1/4" mm Sheet Vinyl 5956 57 D6435.05 (19 mm) (89 mm) (235 mm) Dietrich (16 mm) Carpet and 57 75 E3149.02 oriented R-13 RCSD Woodtype C 132x10 mm Engineered 59 57 D6435.06 Pad strand fiberglass Resilient gypsum CarpetSubfloor and 51 1” 76(25E4054.01 from above in the following: topping: mm) FIRM-FILL® Bran board insulation ¹ Assembly varies Channel board Pad¹

These guidelines shall only be a resource and are not a guarantee of performance. FIRM-FILL® SCM Underlayments are only one compon acoustical performance is affected by every other component. The likelihood of achieving code compliance is contingent upon many other plumbers and drywall contractors. Developers and®general contractors are responsible for building properly ® and testing field performance as so UL Laboratory FireSystem Rated Designs Sound 2: FIRM-FILL SCM-125, (19 mm) Gypsum Concre of the project. tests are not a guarantee of field performance3/4” because of the issuesFIRM-FILL noted above andBrand many other design and/or cons a professional acoustical consultant assureL501, specifications written correctly and that the floor/ceiling assembly can perform to expectation L006, L201, L202, L206, L208, L209, L210, L211, toL212, L502,are L503, L504, L505, L506, L507, L508, L509, ® ® ensure reliability of design prior to occupancy. © 2/2016 Hacker Industries, Inc. FIRM-FILL , GYP-SPAN associated logos are the®re Subfloor topping: 3/4” and (19themm) FIRM-FILL

I-Joist L518, L530, L538, L547, L556, L570, L581, L589, M502, M506, M512

Subfloor Topping 1-1/4” (32 mm) FIRM-FILL® Brand Gypsum Concrete

Sound Mat

Subfloor

3/8" 6" (10 mm) (152 mm) FIRM-FILL® concrete SCM-400 Sound Control Mat

6” (152 mm) CONCRETE ASSEMBLY

SUBMITTAL FORM

Sound System 3: FIRM-FILL® SCM-400, 1-1/4” (32 mm) FIRM-FILL® Brand Gypsum Conc

Subfloor topping: 1-1/4” (32 mm) FIRM-FILL Subfloor isolation: 3/8” (10 mm) FIRM-FILL® Subfloor: 6” (152 mm) concrete

FINISH ® 3310+ – Concrete Assembly Firm Fill InsulationBareTruss Ceiling Ceiling Isolation Bare

None

Sheet Vinyl None Bare

None

STC Finish

Bare Bare

IIC

REPORT #

52 Sound -5014051 Report Rating # -50 7014063 STC IIC -50 7014064 52 -- 5014051 -- -∆ 23*7014063 7014091 50

Sheet -- Method 50 7014064 *Tested in accordance with ASTM E2179 – Vinyl Standard Test for Laboratory Mea -- Through Δ 7014091 Floor Coverings in Reducing Impact Bare Sound Transmission Concrete Floors. 23*

*Tested in accordance with ASTM E2179 - Standard Test Method for Laboratory Measurement of Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors.

Sound System 4: Hacker Sound Mat I, 3/4” (19 mm) FIRM-FILL® Brand Gypsum Concret UL Fire Rated Designs

Concrete J917, J919, J920, J924, J927, J931, J957, J991, J994

FIRM-FILL® SCM sound control mats, Hacker Floor Primer, Hacker TopCoat™ SP and Hacker Floor Sealer are available for use with FIRM-FILL® 3310 Classic. Contact Hacker Industries, Inc. at FINISH (800) 642-3455 f or info@hackerindustries.com or Bare more information.

Warranty

Bare

Subfloor topping: 3/4” (19 mm) FIRM-FILL® B Subfloor isolation: .08” (2 mm) Hacker Sound Subfloor: 6” (152 mm) concrete

Contributes points to LEED Submittal Approvals

Project Name

STC

IIC

REPORT #

5014076

∆ 15*

7014144

Contractor/Architect

certification

Signature

*Tested in accordance with ASTM E2179 – Standard Test Method for Laboratory Mea Subject to express warranty stated on Hacker Industries, Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors.

Inc.’s website.

Date

PRODUCT INFORMATION See www.HackerIndustries.com for current recommended product specifications and literature.

WARNING When mixed with water, this product hardens and becomes extremely WARRANTY hot. DO NOT attempt to make a cast enclosing any part of the body using HACKER INDUSTRIES, INC. SHALL NOT BE LIABLE FOR INCIDENTAL this material. Failure to follow these instructions may cause severe burns OR CONSEQUENTIAL DAMAGES, DIRECTLY OR INDIRECTLY that may require surgical removal of affected tissue or amputation of limb. SUSTAINED, NOR FOR ANY LOSS CAUSED BY APPLICATION OF ® guidelines shall only THESE be a resource and are notIN a guarantee of performance. Underlayments are only one compo Portland cement is strongly alkaline. Direct contact can These be corrosive and GOODS NOT ACCORDANCE WITH FIRM-FILL CURRENTSCM PRINTED performance is affected by every other component. The likelihood of achieving code compliance is contingent upon many othe cause severe damage or chemical burns to eyes and wet,acoustical moist skin. Avoid INSTRUCTION OR FOR OTHER THAN THE INTENDED USE. OUR plumbers and drywall contractors. Developers and general contractors are responsible for building properly and testing field performance as s contact with eyes and skin. Wear protective glasses and clothing. If eye LIABILITY IS EXPRESSLY LIMITED TO REPLACEMENT OF DEFECTIVE of the project. Laboratory tests are not a guarantee of field performance because of the issues noted above and many other design and/or con contact occurs, immediately flush thoroughly with watera professional for 30 minutes GOODS. ANY CLAIM SHALL BE DEEMED WAIVED UNLESS MADE acoustical consultant to assure specifications are written correctly and that the floor/ceiling assembly can perform to expectati and seek medical advice. Inhalation of dust may be corrosive causeof design prior IN WRITING TO©US WITHIN DAYS FROM DATE ®IT WAS, OR ® ensureor reliability to occupancy. 2/2016 Hacker30 Industries, Inc. FIRM-FILL , GYP-SPAN and the associated logos are the chemical burns or irritation to nose, throat and respiratory tract. REASONABLY SHOULD HAVE BEEN, DISCOVERED. Avoid breathing dust. Use a NIOSH/MSHA-approved dust respirator. Wash thoroughly with soap and water after use. Do not ingest. If ingested, call a physician. Product safety, call (800) 642-3455. KEEP OUT OF REACH OF CHILDREN.

SAFETY FIRST 17during installation. Wear Follow good safety/industrial hygiene practices appropriate personal protective equipment. Read specs, MSDS and literature prior to specification and installation. © 2017 Hacker Industries, Inc., Newport Beach, CA.

RECOMMENDED SPECIFICATIONS PART I: GENERAL 1.1

Summary

This section includes underlayment for interior finish flooring.

Related Sections:

1. Section 09 21 16 – Gypsum Board Assemblies

1.2

Referenced Standards

The following standards and publications are applicable:

1. ASTM C472 Modified Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters, and Gypsum Cement (compressive strength)

2. ASTM C33 Standard Specification for Concrete Aggregates (sand aggregate)

3. ASTM D4263 Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method

4. ASTM E90 Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements

5. ASTM E119 Standard Test Methods for Fire Tests of Building Construction and Materials

6. ASTM E413 Rating Classification for Rating Sound Insulation

7. ASTM E492 Standard Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-Ceiling Assemblies Using the Tapping Machine

8. ASTM F2419 Standard Practice for Installation of Thick Poured Gypsum Concrete and Preparation of the Surface to Receive Resilient Flooring

9. ASTM F2678 Standard Practice for Preparing Panel Underlayments, Thick Poured Gypsum Concrete Underlayments, Poured Lightweight Cellular Concrete Underlayments with Underlayment Patching Compounds to Receive Resilient Flooring

10. TCNA F180 Tile Council of North America Installation Handbook

11. NWFA National Wood Flooring Association Instructions

12. Hacker Industries, Inc. Installation Guide

13. Hacker Industries, Inc. Drying Conditions Flyer

14. Hacker Industries, Inc. Guidelines for Installing Finished Floor Coverings

15. UL Fire Resistance Directory

RECOMMENDED SPECIFICATIONS (CONT.)

1.3

Submittals

Product Data: Submit manufacturer’s specifications and installation instructions with project conditions and materials clearly identified or detailed for each required product or system.

Environmental Information: Submit product data for LEED® Credits MR 4 and MR 5, Recycled Content and Regional Materials. Provide documentation indicating percentages, by weight, of post-consumer and pre-consumer recycled content. Also provide documentation substantiating Regional Materials.

1.4

Quality Assurance

Fire Resistance: Provide materials and construction identical to those tested according to ASTM E119 by an independent testing agency.

Acoustical Performance: For STC: Provide materials and construction identical to those tested in assembly indicated according to ASTM E90 and classified according to ASTM E413 by an independent testing agency. For IIC: Provide materials and construction identical to those tested in assembly according to ASTM E492.

Manufacturer: All materials, unless otherwise indicated, shall be manufactured by Hacker Industries, Inc., Newport Beach, California.

Installer: Installation of FIRM-FILL® 3310 Classic Gypsum Concrete Floor Underlayment shall be by a Licensed Applicator of Hacker Industries, Inc., using mixing and pumping equipment with a water meter approved by Hacker Industries, Inc.

Hacker Industries, Inc., Newport Beach, CA, shall approve all materials specified herein. All others must receive prior approval.

1.5

Performance Requirements

1.6

Delivery, Storage And Handling

1.7

Project Conditions

1.8

Warranty

Certification: Upon completion of this portion of the work, and as a condition of its acceptance, deliver to the architect a certificate from Hacker Industries, Inc., and signed by the Licensed Applicator, stating that the material used in this work complies with the specified requirements.

Subject to express warranty as stated on Hacker Industries, Inc.’s website.

Compressive strength of FIRM-FILL® 3310 Classic Gypsum Concrete Floor Underlayment shall be from 3000 to 3900 psi (approx. 13.8 to 22.8 MPa)

Materials shall be delivered in their original, unopened packages and protected from exposure to the elements after delivery. Do not allow the bags to get wet.

Before, during and after installation of product, building interior shall be enclosed, with adequate ventilation and heat maintained at a temperature above 50°F (10°C) to allow for drying of product.

RECOMMENDED SPECIFICATIONS (CONT.)

PART II: PRODUCTS 2.1

Manufacturers

Acceptable Manufacturers, subject to all the requirements contained herein: 1. Hacker Industries, Inc., Newport Beach, California

2.2

Material Description

Gypsum Concrete: FIRM-FILL® 3310 Classic Gypsum Concrete Floor Underlayment, supplied by Hacker Industries, Inc.

Subfloor Primer: Hacker Floor Primer or approved equal

Sand: Washed plaster or masonry sand meeting the requirements of Hacker Industries, Inc. Sand Guidelines

Water: Potable and free from impurities

Sealer: Hacker TopCoat™ SP Surface Preparation Agent, if specified

PART III: EXECUTION 3.1

Examination

Condition of Subfloor

1. Subfloor shall be structurally sound, broom cleaned, dry and free from oil, grease, paraffin, laitance or other contaminants before the arrival of the Hacker Licensed Applicator.

2. Wood Substrate:

a. Subfloor and framing must be designed to a maximum deflection of L/360.

b. Wood should be APA rated 23/32” (1.8 cm) T&G.

3. Concrete Substrate: shall be in place a minimum of 28 days.

4. Before installation, the General Contractor (GC) shall inspect and approve the condition of the subfloor and test for dryness.

3.2 Preparation

Leak Prevention: All cracks and voids should be filled with a quick-setting patching or taping compound, or equal, where leakage may occur.

Prime wood subfloors with one coat of Hacker Floor Primer (diluted 4:1 with water) using one gallon of primer solution (approx. 3.79 L) per 500 ft2 (approx. 47 m2). Hacker Floor Primer is not always required over concrete substrates. Multiple coats may be required over porous concrete or plank. (Note: For rehabilitation work or pours over old and/or porous concrete or wood, consult a Licensed Applicator or Hacker Industries, Inc. for recommended floor preparation.)

Installation of FIRM-FILL® 3310 Classic Gypsum Concrete Floor Underlayment shall not begin until the building is enclosed, including roof, windows, doors, and other openings.

FIRM-FILL® 3310 Classic Gypsum Concrete Floor Underlayment may be installed before or after the installation of drywall, as specified.

RECOMMENDED SPECIFICATIONS (CONT.)

3.3 Installation

Mixing Instructions: Add 80-pound (36.3 kg) bag of FIRM-FILL® 3310 Classic to 6 to 7 gallons (22.7 to 26.5 L) of water followed by the specific sand ratio. Do not overwater. Water amount will vary with the wetness of the sand.

This is the proper sequence for mixing of FIRM-FILL® 3310 Classic.

First add water to bucket followed by FIRM-FILL® 3310 Classic and finally the sand.

Application: The minimum thickness of FIRM-FILL® 3310 Classic Gypsum Concrete Floor Underlayment varies with the type of subfloor. Over wood subfloors, a minimum of 3/4” (approx. 19 mm) is required. Over precast or poured-in-place concrete, a minimum of 1/2” (approx. 13 mm) is required.

FIRM-FILL® 3310 Classic Gypsum Concrete Floor Underlayment is suitable for interior applications only and must be covered by a finished floor material.

Protection: After installation, the GC shall place temporary wood planking wherever the floor underlayment will be subject to wheeled or concentrated loads.

Drying: Before, during and after installation of FIRM-FILL® 3310+ Gypsum Concrete Floor Underlayment, building interior must be ventilated and heated to a minimum 50°F (10°C) to ensure completion of the drying process. The GC shall provide continuous ventilation and adequate heat to rapidly remove moisture from the area until the FIRM-FILL® 3310+ Gypsum Concrete Floor Underlayment is dry. Do not install finished floor coverings until the FIRM-FILL® 3310+ Gypsum Concrete Floor Underlayment is tested for dryness. Consult flooring contractor for recommended procedures to test for dryness. Reference Hacker Industries, Inc.’s Drying Conditions Flyer.

Field Quality Control:

1. Slump Test: FIRM-FILL® 3310+ Gypsum Concrete Floor Underlayment shall be tested for slump at the beginning of each installation in order to establish the required slump. Slump tests shall then be taken periodically during installation to verify that the required slump is maintained. Slump tests shall be conducted using a 2” by 4” (approx. 51 mm by 102 mm) cylinder. The acceptable patty size should be 8.5” (approx. 216 mm) plus or minus 1/2” (approx. 13 mm) in diameter. 2. Field Samples: Testing shall be done in accordance with ASTM C472 modified testing procedures, using 2” (approx. 51 mm) split brass molds. Prior to independent sampling, contact Hacker Industries, Inc., to ensure that proper ASTM procedures are followed. If requested prior to installation, test results shall be available to the architect and/or contractor from the Licensed Applicator. 3.4 Preparation For Finished Floor

Repair any damaged areas of underlayment prior to application of any sealers.

Underlayment must be dry prior to installation of finished floor. Follow ASTM D4263 to determine dryness of underlayment.

Resilient Floor Applications: Follow floor covering manufacturer’s guidelines for proper applications and procedures (ASTM F2419).

Install wood flooring according to NWFA Instructions.

Install ceramic, porcelain, granite or natural stone tiles according to TCNA recommendations.

PROJECT REFERENCES Ideal over wood or concrete subfloors in multi-family, renovation projects and custom homes, FIRM-FILL® 3310+ helps maximize sound control and creates a flat, durable surface for finished floor coverings. FIRM-FILL® 3310+ offers an innovative formulation that decreases the amount of water used while enhancing the rock-solid floor strength, up to 3300 psi. Below is a small sample of projects that have utilized FIRM-FILL® 3310+. Contractor: Barnhill Contracting Project: West Village (Renovation) Location: Durham, North Carolina Description: 190,000 ft² of FIRM-FILL® 3310 over Hacker Sound Mat II Contractor: Bozzuto Construction Project: Jericho Senior Apartments Location: Landover, Maryland Description: 245,000 ft² of FIRM-FILL® 3310 Contractor: Coryell Enterprises Project: Orchard Park Apartments Location: Springfield, Missouri Description: 164,292 ft² of FIRM-FILL® 3310 Contractor: D.R. Horton Project: Grande at Riverdale Location: Riverdale, New Jersey Description: 350,000 ft² of FIRM-FILL® 3310 over Hacker Sound Mat II Contractor: Fairfield Development Project: Addison Residential Location: Addison, Texas Description: 354,351 ft² of FIRM-FILL® 3310 Contractor: HA Anderson Project: Meadow Lake Village Location: Meridian, Idaho Description: 148,000 ft² of FIRM-FILL® 3310 Contractor: Hy-Max Building Corporation Project: Halsted/Zelzah Apartments Location: Northridge, California Description: 20,180 ft² of FIRM-FILL® 3310 Contractor: LCG Pense Project: Bozeman Village Assisted Living Location: Bozeman, Montana Description: 76,000 ft² of FIRM-FILL® 3310 Contractor: Legacy Project: Coggins Drive Apartments / Vineyards Location: Pleasant Hill, California / Gilroy, California Description: Various projects with FIRM-FILL® 3310

FIRM-FILL® 3310+, a premium poured floor underlayment from Hacker Industries, Inc., delivers best in class performance with compressive strengths from 3000-3900 psi. Ideal over wood or concrete subfloors in multi-family, hospitality, and renovation projects, FIRM-FILL® 3310+ maximizes sound control and creates an enhanced surface for finished floor coverings. • Easy application, fast setting; light traffic can return within hours • Over 100 UL Fire Rated Design listings; ICC-ES Legacy Report • Can be poured before or after drywall, as specified • Specify with FIRM-FILL® SCM acoustical control mats for improved acoustical performance • Meets ASTM F2419 and Tile Council of North America F180, F200 • Installed by trained Licensed Applicators

1 - FLOOR COVERING / 2 - FIRM-FILL® 3310 GYPSUM CONCRETE UNDERLAYMENT / 3 - FIRM-FILL® SCM OR 6 - BATT INSULATION / 7 - PARALLEL CHORD TRUSS / 8 - TJI ® JOIST / 9 - RESILIENT CHANNEL / 10 - GYPSUM

i 00 ps 0-32 nt ® Rad®ia 200 1 - FLOOR COVERING / 2 - FIRM-FILL 3310 GYPSUM CONCRETE UNDERLAYMENT / 3 - FIRM-FILL SCM OR HA AN P S ® RM-FILL SCM OR HACKER SOUND MAT / 4 - PLYWOOD OR 6 OSB / 5 - INSULATION NOMINAL WOOD JOIST / P- BATT / 7 - PARALLEL CHORD TRUSS / 8 - TJI ® JOIST / 9 - RESILIENT CHANNEL / 10 - GYPSUM W GY NEL / 10 - GYPSUM WALLBOARD / 11 - 6” CONCRETE 2000-3300 psi ®

D M

mC onc ret e

1200200 0p FIRM s -FIL i Gypsu L®

si FIRM-FILL ® 0p ® 3310 20 L 3 IL 000 M-F 0+psi IR0-322001 psi nt ® Radia 200 nt PAN ® Radia SOSB mi ® ® 1 - FLOOR COVERING / 2 FIRM-FILL 3310+ CONCRETE UNDERLAYMENT / 3 FIRM-FILL SCM OR HACKER SOUND MAT / 4 PLYWOOD OR / P n. FIWOOD GY 5 - NOMINAL / 6 - BATT INSULATION / 7 - PARALLEL CHORD TRUSS / 8 - TJI ® JOIST / 9 - RESILIENT CHANNEL / 10 - GYPSUM WALLBOARD / 2000-3300 psi RM 35JOIST 00 11 6” CONCRETE 3 0 3 F 0 0 p 0 p s 0 i 2 IL s i s FIRM-FILL ® i L® p ® 25 ILLHACKER 00 ® IRM-FOR FILL®FSCM SOUND MATC/ 4 - PLYWOOD OR OSB / 5 - NOMINAL WOOD JOIST / 3310 0 2 0 L 3 0 psi 1000 psi 2000 psi 3000 psi 4000 psi 5000 psi 6000 psi IL 03310 FIR -3/8011 - 6” CONCRETE / 10 - GYPSUM WALLBOARD F 0 0 0 M 0+ Hig M-F p IR 201 hS I tre LL mC onc ret e

1200200 0p FIRM s -FIL i Gypsu L®

4000-5200 psi

2000-3200 psi

Firm-Fill® CMD

3000-3900 psi

Gyp-Span Radiant

2000-3200 psi

2500-3800 psi

True-Screed CLU

up to 6000 psi

min. 3500 psi

2000-3300

3000-3900

psi 200 0-5 ® 400 ILL M-F FIR 010 4

psi 000 to 6 D® CLU up REE -SC UE TR

en g

Firm-Fill® 4010+

D M

25 00 FIR -380 0 Hig M-F p hS IL tr L th

esom

p IL L ® si C

MPa)

50 M- Strength Firm-Fill® RHigh 0 F

1200-2000 psi

pres0 from

psi 000 to 6 D® CLU up REE -SC UE TR

mi Firm-Fill® 3310+ n

psi 200 0-5 ® 400 ILL M-F FIR 010 4

Firm-Fill® 2010+

2000-3300 psi FIRM-FILL ® 3310

diant

Firm-Fill® Gypsum Concrete

High-strength for use over wood or concrete subfloors

UL for 1 to 2 hour fire ratings

Provides UL designIdeal listingsfor Fast installation & Provides Installedcompresby multifor High-strength compressive for 1 to 2 hour fire rapid set; walk on Hacker Industries' family construction wood or ratings over from strengths use strengths in 90 minutes sive trained Licensed from 3000-3900subfloors psi Applicatorspsi concrete 2000-3300 (20.6-26.8 MPa) (13.8-22.8.8 MPa)

Ideal for multiHigh-strength for Fast installation & Installed only by family construction use over wood or rapid set; walk on Hacker Industries’ concrete subfloors in 90 minutes L/360 Licensed Applicators

UL design listings for 1 to 2 hour fire ratings Requires dryin (building must be fully enclosed before design listings installation)

Ideal for multifamily construction

2000-3300

Not a wear surface; requires finished floor covering

Hacker Industries, Inc. |

Deflection must not exceed L/360 live or dead load

Subfloor must be protected by vapor barrier if installed above by onlyspace Installedcrawl

Provides compressive strengths from 2000-3300 psi (13.8-22.8.8 MPa)

One component of an effective sound & fire control system

Fast installation & on rapid set; walk Hacker Requires dry-in Industries’ Not a wear surface; in 90 minutes(building must Licensed be Applicators requires finished Architect Binder | Firm-Fill® 3310+ | © 2017 fully enclosed floor covering

UL for rati

UL de for 1 t rating

Wear appropriate personal protective equipment

Deflection must not exceed L/360 39 live or dead load

Su pro bar

SUBMITTAL FORM TECHNICAL DATA

PROPERTIES

ASTM

Weight

7.6 lb/ft² (37.1 kg/m²) at 3/4” (19 mm)

C472 M

Thickness

Wood: 3/4” (19 mm) to 3-1/2” (89 mm); Concrete: 1/2” (13 mm) to 3-1/2” (89 mm)

F2419

Compressive Strength

3000 to 3900 psi (20.6 to 26.8 MPa)

C472 M

Thermal Performance

K-value of 2.8 BTU/(hr.ft.F°); R-value of 0.36 (ft².hr.F°)

C177

Fire Hazard Classification

Flamespread index 0: Fuel contribution 0; Smoke density 0

E84

Sand

1/8” (3 mm) or less washed plaster or masonry sand

C33

Flexural Strength

1200 psi (8.27 MPa)

C348

Benefits • • • • • • • • •

High-strength underlayment for use over wood or concrete subfloors Install over a FIRM-FILL® SCM or Hacker Sound Mat for additional sound isolation Contributes to excellent STC and IIC ratings UL fire-rated designs for 1 to 3 hour fire ratings Lightweight and crack-resistant Reduced amount of water for accelerated drying time Contributes points to LEED® project certification Creates a flat, durable, non-structural underlayment surface for finished floor coverings Installed only by trained Licensed Applicators across North America

Product Description Specifically designed for new, thin laminates, this product’s rapid set time allows light foot traffic in 90 minutes. This versatile, high quality floor underlayment is widely used as an alternative to lightweight concrete in multi-family, light commercial and hospitality projects. FIRM-FILL® 3310+ provides compressive strengths from 3000 to 3900 psi (20.6 to 26.8 MPa). Depending on compressive strength, it can be installed before or after drywall. To help keep projects on schedule and on budget, Licensed Applicators can install over 25,000 ft² of FIRM-FILL® 3310+ in one day. FIRM-FILL® 3310+ is mixed on the job site with local sand (per ASTM C33) and water to create a lightweight slurry. Installed at a minimum of 3/4” thick, the underlayment weighs approximately 7.6 lb/ft² (37 kg/m²) with a dry density range of 107-120 pcf. For new construction, FIRM-FILL® 3310+ is a cost-efficient way to maximize sound control and create a smooth, flat and high-strength surface for finished floor coverings. To achieve additional sound isolation, use FIRMFILL® 3310+ with either a FIRM-FILL® SCM or Hacker Sound Mat.

Limitations • Do not use FIRM-FILL® 3310+ in exterior locations, below grade or where continuous exposure to moisture is likely. • Shall not be used as a wear surface; must be covered by a finished floor covering. • Structure shall be designed so that deflection does not exceed L/360 live or dead load. Certain floor coverings, such as marble, limestone, travertine and wood, may have more restrictive deflection limits. Consult the appropriate floor covering manufacturer for recommendations. • If installed above a crawl space, subfloor must be protected by a vapor barrier. • No single application of FIRM-FILL® 3310+ shall exceed 3” in depth. • FIRM-FILL® 3310+ is one component of an effective sound and fire control system. Care must be taken in the installation of all components to assure the ultimate design performance. Published acoustical and fire system tests were conducted under controlled laboratory or field conditions and reflect results applicable only to those specific assemblies. 40

SUBMITTAL FORM Installation Before, during and after the installation of FIRM-FILL® 3310+, the building must be enclosed and the temperature maintained at a minimum of 50°F (10°C). Prior to the installation of FIRM-FILL® 3310+, the subfloor shall be structurally sound (L/360), broom cleaned, dry and free from oil, grease, paraffin, laitance, wax or other contaminants. Concrete subfloors shall be 28 days or older. For on-grade applications over concrete, measure the Moisture Vapor Emission Rate (MVER) per ASTM F1869. MVER shall not exceed 3 lb/1000 ft² per 24 hours. Prime wood subfloors with Hacker Floor Primer per recommended specifications before installing underlayment. Adequate ventilation shall be provided by the General Contractor (GC) to ensure proper drying of FIRMFILL® 3310+. If necessary, the GC shall provide mechanical ventilation. Depending on thickness and drying conditions, the underlayment should dry within 10 to 14 days. To avoid potential problems during the drying process, the GC shall consult Hacker Industries, Inc.’s Drying Conditions Flyer and information contained on Hacker Industries, Inc.’s website for additional information concerning drying of this product. After installation, temporary wood planking shall be placed by the GC wherever the floor underlayment will be subject to wheeled or concentrated loads. Finished floor coverings can be installed when the FIRM-FILL® 3310+ is completely dry. Consult flooring contractor for recommended procedures to test for dryness and acceptable levels of moisture. Reference Hacker Industries, Inc.’s Guidelines for Installing Finished Floor Coverings. This guideline is not a warranty and shall be used as a guideline only. See ASTM F2419.

Product Data Approximate Compressive Strength per ASTM C472 Modified: Approximate Dry Density (aggregated):

3000 to 3900 psi* (20.6 to 26.8 MPa) 107 to 120 pcf

Compliance • ICC-ES ER-4147 • City of Los Angeles Research Report No. 24540

• FHA-HUD MR 1255 • Tile Council of North America (F180, F200, RH111, RH122)

Sound Test & UL Fire Rated Designs PURPOSE STATEMENT/DISCLAIMER

These guidelines are designed to provide the architectural and building communities with detailed performance data on Hacker Industries, Inc.’s comprehensive portfolio of sound attenuation tests and UL Fire Rated Designs. The tests for the assemblies included in these guidelines were conducted in a laboratory setting per ASTM C177, E84, E90, E492 and E2179. These guidelines are not warranties and should be used as guidelines only. The architects’ and general contractors’ recommendations supersede these guidelines. Field performance may vary. Subject to express Warranty stated on Hacker Industries, Inc.’s website. Hacker Industries, Inc. regularly performs acoustical and fire (UL) testing to ensure performance standards for our products. Firm Fill® gypsum concretes, including Firm Fill® 3310+, were tested acoustically with the following floor assemblies and performed as noted.

OPEN WEB

Sound System 1: No Sound Mat, 3/4” (25 mm) FIRM-FILL® Brand Gypsum Concrete

SUBMITTAL FORM

Subfloor Topping

Sound Mat

3/4” None (25mm) FIRM-FILL® Brand Gypsum Concrete

Subfloor

3/4” (19 mm) oriented strand board

5/8” (16 mm) type C gypsum board

STC Finish

Bare¹

IIC

REPORT #

54 Sound -Rating 51 -STC IIC 52 75

5005002 Report # D6435.29

D6435.30

5005002

Bare

52 7004018 -D6435.29

Carpet and Pad

75 54

D6435.30 7004025

7004018

Wood Laminate²

NOMINAL WOOD

Subfloor Topping

Sound Mat

3/4” None (19 mm) FIRM-FILL® Brand Gypsum Concrete

Nominal Wood

IIC

REPORT #

These guidelines shall only be a resource and are not a guarantee of performance. FIRM-FILL® SCM Underlayments are only one compon acoustical performance is affected by every other component. The likelihood of achieving code compliance is contingent upon many other plumbers and drywall contractors. Developers and®general contractors are responsible for building properly ® and testing field performance as so UL Laboratory FireSystem Rated Designs Sound 2: FIRM-FILL SCM-125, (19 mm) Gypsum Concre of the project. tests are not a guarantee of field performance3/4” because of the issuesFIRM-FILL noted above andBrand many other design and/or cons a professional acoustical consultant assureL501, specifications written correctly and that the floor/ceiling assembly can perform to expectation L006, L201, L202, L206, L208, L209, L210, L211, toL212, L502,are L503, L504, L505, L506, L507, L508, L509, ® ® ensure reliability of design prior to occupancy. © 2/2016 Hacker Industries, Inc. FIRM-FILL , GYP-SPAN associated logos are the®re Subfloor topping: 3/4” and (19themm) FIRM-FILL

I-Joist L518, L530, L538, L547, L556, L570, L581, L589, M502, M506, M512

STC

Subfloor Topping 1-1/4” (32 mm) FIRM-FILL® Brand Gypsum Concrete

Sound Mat

Subfloor

3/8" 6" (10 mm) (152 mm) FIRM-FILL® concrete SCM-400 Sound Control Mat

6” (152 mm) CONCRETE ASSEMBLY

SUBMITTAL FORM

Sound System 3: FIRM-FILL® SCM-400, 1-1/4” (32 mm) FIRM-FILL® Brand Gypsum Conc

Subfloor topping: 1-1/4” (32 mm) FIRM-FILL Subfloor isolation: 3/8” (10 mm) FIRM-FILL® Subfloor: 6” (152 mm) concrete

FINISH ® 3310+ – Concrete Assembly Firm Fill InsulationBareTruss Ceiling Ceiling Isolation Bare

None

Sheet Vinyl None Bare

None

STC Finish

Bare Bare

IIC

REPORT #

52 Sound -5014051 Report Rating # -50 7014063 STC IIC -50 7014064 52 -- 5014051 -- -∆ 23*7014063 7014091 50

*Tested in accordance with ASTM E2179 - Standard Test Method for Laboratory Measurement of Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors.

Sound System 4: Hacker Sound Mat I, 3/4” (19 mm) FIRM-FILL® Brand Gypsum Concret UL Fire Rated Designs

Concrete J917, J919, J920, J924, J927, J931, J957, J991, J994

FIRM-FILL® SCM sound control mats, Hacker Floor Primer, Hacker TopCoat™ SP and Hacker Floor Sealer are available for use with FIRM-FILL® 3310+. Contact Hacker Industries, Inc. at FINISH (800) 642-3455 f or info@hackerindustries.com or Bare more information.

Warranty

Bare

Subfloor topping: 3/4” (19 mm) FIRM-FILL® B Subfloor isolation: .08” (2 mm) Hacker Sound Subfloor: 6” (152 mm) concrete

Submittal Approvals

Contributes points to LEED® certification

STC IIC Project Name

5014076

∆ 15*

7014144

Contractor/Architect

REPORT #

Signature with ASTM E2179 – Standard Test Method for Laboratory Mea *Tested in accordance Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors. Subject to express warranty stated on Hacker Industries,