Agri News - July 2023

UNRIVALLED EXPERIENCE AND EXPERTISE IN GREEN BEDDING

With more Separators and Green Bedding systems installed UK and Worldwide, Bauer is uniquely qualified to provide advice, products and support for your Green Bedding System

■ ECONOMICAL

■ ALWAYS AVAILABLE

■ INCREASED COW COMFORT

■ CLEANER COWS

■ NO DUST

“Cows have cleaned up no end definitely as clean as cows on sand and the number of mastitis cases has dropped dramatically.”

Defra permit the use of RMS (Recycled Manure Solids) as bedding for dairy cattle. Farms using RMS must notify APHA and Red Tractor

“Having an unlimited supply of material means you can use more of it.”

YEAST FERMENTATION ADDITIVE REDUCES LAMB FINISHING TIMES

Yeast fermentation additive reduces lamb finishing times, resulting in an additional £18.91 per head profit

Yeast fermentation additive reduces lamb finishing times, resulting in an additional £18.91 per head profit

Data collected in a 2022 farm trial found that lambs supplemented with Celmanax, a yeast fermentation additive, from weaning to slaughter resulted in a £18.91 per head advantage compared to lambs not provided additional supplementation when cost of feed was taken into consideration.

According to Dr Alison Bond, nutritionist for Rumenco and UK distributor of Celmanax, the biggest contributor to the increase in profit was a significant increase in daily liveweight gains resulting in faster finishing times. Of the lambs supplemented with Celmanax, 50% were finished by the end of June and an additional 35% were finished by the trial end. Only 8% of unsupplemented lambs were finished in June, with an additional 17% finished by the end of the trial, resulting in 75% of the control group remaining unfinished at the end of the trial.

“The nutritional benefits from Celmanax allowed lambs to achieve an average daily gain of 530g in the first four weeks of the trial, a 150g advantage over the control group that had an average daily gain of 380g,” explains Dr Bond.

Beginning on May 15 and ending on July 25, over 650 10-week-old lambs on a commercial sheep farm in Wales were split into supplemented and control groups. Lambs had negative worm counts, were managed on paddocks with a sward height of 9cm (2,500 kg

DM/ha) and had free access to a Rumenco mineral bucket.

Each group was supplemented with creep feed, allocated 1kg/h/ day. The control group was fed standard creep feed and the treatment group received creep feed containing Celmanax to provide 0.5g/h/d.

“Celmanax is a yeast fermentation additive that has been shown to improve ruminant performance by supporting a stable rumen environment. A range of compounds within this product supports the maintenance of a stable rumen microbiome, therefore improving digestibility and feed efficiency,” explains Dr Bond.

Financial and environmental advantages of yeast fermentation products for sheep farmers

According to Dr Bond, the financial return of feeding Celmanax was achieved through a combination of fewer days on farm and the lambs earning a higher price by hitting the market early.

“If you look back through market trends, lamb price will be strong throughout June and then start to decline as you get into July and August. This is because the majority of lambs are finishing in the July-August period, flooding the market and driving down prices,” she says. In June 2022, the average deadweight lamb price was 671.73 p/kg, dropping to 636.35 p/kg in July and even further to 544.90 p/ kg in August.

Fewer days on farm, also equate to fewer resources like water, grass

and labour being required, adds Dr Bond, which was not taken into the financial calculations on this trial. However, using industry data, Rumenco estimates that Celmanax supplementation reduced enteric methane emissions throughout the trial period by 18.7% compared to the control group.

Yeast fermentation feeding options

Sheep farmers wanting to take advantage of the rumen support and average daily gain benefits of Celmanax have a couple of feeding options, says Dr Bond.

The first is to feed it in a creep compound like the trial farm. The recommended feeding rate is 0.5g/h/day to be fed from weaning through to finish.

The second option is to supplement lambs from weaning through to finish with a multipurpose product like Rumevite Quality Lamb, which replaces concentrates. Good frame growth and weight gain are achieved through the block’s 18 percent all-natural protein content and 13 ME. Lambs also benefit from the formulation which includes essential trace elements, vitamins and minerals. This includes vitamin B1, selenium, cobalt and protected zinc.

The combination of nutrients in Rumevite Quality Lamb provides huge performance benefits. In a 2018 trial, lambs supplemented with Rumevite Quality Lamb had an average daily liveweight gain over double that of the control group and were finished 81 days quicker, with a 390g heavier finishing weight.

ADDRESSING THE PRODUCTIVITY GAP IN UK AGRICULTURE

Current taxpayer funding of applied and near-market agricultural R&D is not delivering value for money.

Current taxpayer funding of applied and nearmarket agricultural R&D is not delivering value for money. With growth in UK agricultural productivity lagging seriously behind competitor countries, including those with lower public investment in research and innovation, agribusiness consultant James Wallace calls for a new approach to determining R&D spending priorities and subsequent knowledge transfer onto farm.

UK agriculture urgently needs to improve its productivity.

Higher productivity –producing more output per unit of input - is essential for UK farming to compete in the global market. It is the foundation for a successful, profitable and sustainable farming industry in post-Brexit Britain.

And yet UK agricultural productivity growth lags seriously behind our competitors.

Just over three years ago, in February 2020, the Food & Drink Sector Council’s Agricultural Productivity Working Group (APWG), chaired by former NFU President Sir Peter Kendall, issued a report warning that UK farming productivity growth is not achieving its

potential.

The report noted that UK agricultural productivity has grown by just 18% since 1991, significantly lower than other countries such as the Netherlands (52%), United States (54%) and France (82%).

Left untouched, and confronted with a new set of challenges – including greater post-Brexit exposure to global markets, changes to farm support policies, climate change and commitments to achieve net zero emissions - the APWG report warned that Britain’s farming industry faces decline, denying consumers and our domestic food industry the affordable, sustainably produced agricultural goods they demand.

Of course, the report was written before the Covid pandemic and war in Ukraine took their toll. The ensuing cost-of-living crisis and food price crunch, with food inflation reaching its highest level for 45 years, have further underlined the urgent need for UK agriculture to focus on improving its productivity.

The APWG report also made clear that improving agricultural productivity is emphatically not about producing more with no

thought to the environmental consequences or consumer expectations, indeed to the contrary: “the prize of greater productivity is significantly better use of our natural, environmental resources”.

The report added that higher productivity growth can be closely correlated to reduced environmental impact and is therefore also aligned with wider sustainability objectives.

In pointing the way forward to tackle UK agriculture’s productivity gap, the APWG report called for urgent action to address a fragmented knowledge exchange landscape, “tackling the problems associated with having a wide range of delivery bodies, variable messaging and no central point for quality assured advice.”

It also highlighted the need to ensure innovation funding and research strategy are geared towards the needs of the industry.

I couldn’t agree more.

Taxpayer-funded R&D expenditure must be targeted on those areas where technology and innovation will yield the greatest benefits.

NEW RESEARCH SET TO INCREASE CARBON CAPTURE THROUGH CROPPING

A new research project aims to help UK farmers and growers target Net Zero and build farming resilience through diversifying cropping

Anew research project aims to help UK farmers and growers target Net Zero and build farming resilience through diversifying their arable and forage cropping. It will also enable new revenue sources through a carbon marketplace and support enhanced value chains for industries such as textiles and construction.

The Centre for High Carbon Capture Cropping (CHCx3) is a four-year, £5.9 million project, supported by a consortium of 22 industry and research partners and led by crop science organisation NIAB. The project, which runs from spring 2023 to 2027, has been awarded funding by Defra under the Farming Futures R&D Fund: Climate Smart Farming. This forms part of Defra’s Farming Innovation Programme, delivered in partnership with Innovate UK.

The research will focus on four cropping options: rotational cover crops; annual fibre crops (industrial hemp and flax); perennial food, forage and feed crops (including cereals and herbal leys); and perennial biomass crops (miscanthus, willow and poplar). In addition to evaluating their potential

to enhance atmospheric carbon capture and sequestration, in the soil and crop-based products, CHCx3 will examine the effects of cultivation system and agronomy on economic returns and other environmental outcomes. Further work will optimise the production and use of renewable biomaterials for fibre, textiles, and construction and develop carbon insetting/offsetting platforms.

The Centre’s ‘Knowledge Hub’ will provide resources to support the effective uptake and utilisation of crops with high carbon-capture potential, with practical outputs such as crop guides, web tools and apps available to landowners, farmers and agronomists. The project will offer a wealth of opportunities for its many stakeholders to engage with and participate in the ongoing research, including crop trials, field demonstrations, webinars, workshops and training.

Project Lead and Head of NIAB Innovation Farm Dr Lydia Smith explains that crop choice, management and utilisation all offer opportunities. “Farmers and associated industries can address climate change

goals through input-efficient crops that are able to increase carbon capture, but they must have confidence in achieving profitable and sustainable outcomes,” says Dr Smith.

Project Knowledge Exchange

Lead and NIAB Director of Agronomy Stuart Knight highlights that the Centre will build on NIAB’s extensive programme of crop diversity and improvement, farming systems and soils research. “The project will kick-start vital new collaborations between researchers, seed suppliers, growers and industries seeking to realise the full potential of cropbased products, establish new revenue opportunities within the carbon market, and give a major boost to our shared aim of achieving Net Zero,” concludes Mr Knight.

BAUER POLYESTER TANKERS

YOUR ADVANTAGES:

• Low ground pressure

• Minimum compaction

• High capacity pumps

• Heavy duty galvanised chassis

• Strong non corrosive tanks

• Wide range of distribution systems

MOST EFFICIENCE AND COST EFFECTIVE

Polyester tankers with trailing shoe applicator, from 10.500 up to 24.000 liters

SEPARATOR

Eccentric screw pump HELIXDRIVE

Submersible pump MAGNUM CSPH

Submersible motor mixer MSXH

Tractor mixer MTXH-L

Centrifugal pumps MAGNUM

ECKART Mixers for Biogas

PLUG & PLAY portable pump and separator unit for multi-site operation

KUHN: BALER AND GRASSLAND TOUR 2023

Kuhn Farm Machinery has released details of its 2023 baler and grassland demonstration tour which will feature fixed and variable chamber balers

KUHN Farm Machinery has released details of its 2023 baler and grassland demonstration tour which will feature fixed and variable chamber balers, square balers and combination machines alongside a selection of grassland machinery throughout the 2023 season.

“Working with our dealer network throughout the UK, will enable farmers and contractors to experience our comprehensive range of balers and other KUHN green harvest machinery in a familiar setting. We believe there is nothing better than an on-farm demonstration. This year

we have a dedicated web page to help potential customers locate demo machines,” product specialist Rhodri Jenkins explains.

The demonstrations are part of KUHN’S Go Further with Your Forage initiative that seeks to show how machinery can help maximise green harvest yield and quality. KUHN has allocated a total of 20 machines to cover the UK including KUHN’s triple mowers, tedders and rakes along with the Merge Maxx 1090.

“It is an opportunity

to see machinery working in real life conditions and a chance to speak to our specialists about the specification and capabilities of our balers and green harvest equipment,” adds Mr Jenkins.

For more information on the KUHN baler and grassland tour visit www.kuhn.co.uk/ go-further-your-forage

Southam Agricultural Fields Farm, Station Rd, Southam CV47 2DH t: 01926 813426

www.southamagri.co.uk

BRITISH PLOUGHING RETURNS TO SOMERSET

The organisers of the annual British National Ploughing Championships & Country Festival are delighted that the event will return this year

The organisers of the annual British National Ploughing Championships & Country Festival are delighted that the event will return to Somerset this year, when it will be held on 14th and 15th October 2023. This fantastic event, held in a different part of the country each year, will be returning to the county of Somerset for only the seventh time in its’ 72 year history when the Championships will be held on land at Bishop’s Lydeard, near Taunton by kind permission of K S Coles and family.

Partnering once again with Cereals Event, the Championships are proving to be as proving to be as popular as ever, with a deluge of both trade exhibitors/demonstrators and ploughing entries which will fill the massive 250 acres (100 hectares) site.

Over the two days, with a total of around 300 ploughing plots to complete, ploughmen and women from throughout Great Britain will be striving for perfection and will use a variety of modern tractors, vintage tractors or magnificent heavy horses to

do so. They will be in one of fifteen different ploughing classes or six ‘Plough-Off’ Finals and their aim is to be British Champion in their respective discipline. For the finalists, their aim is to be Supreme Champion and win a place to represent their country overseas in the 2024 World or European Ploughing Contests.

Visitors to the Championships will not only be able to appreciate the ploughing skills on show, they will also be able to shop in the trade stand, shopping and craft area for anything from a tractor or a barn; to a garden trug or a children’s puzzle. They will also be able to see local and national companies demonstrating the most upto-date machinery available on the market today and in contrast, many vintage tractors and implements on display from yesteryear.

One of the most popular attractions from the past are the giant steam ploughing engines which will be pulling a ridden plough between them from one end of a field to another. There will also be hedgelaying competitions and demonstrations in

varying different styles and to get around the fields to see everything, tractor and trailer rides will be provided.

Sue Frith, Chief Executive of the Society of Ploughmen, who are organising the event, said “We have some exceptional support in the south-west of the country and we are delighted that the Coles family have invited us back to Somerset for the third time in recent years. In 2017 we held one of our best-ever Championships on their land and we’re looking forward to a repeat, if not better this year!”

Space for trade stands, demonstrations, shopping stalls and crafts are booking fast and sponsorship opportunities are available for both market leaders and small companies with main sponsors this year being Bridgestone/Firestone and Aztec Oils.

Further information can be found on www.ploughmen. co.uk or from the Society of Ploughmen on 01302 852469 and you can follow them on Facebook and Twitter.

NEW DX140LC-7K 14T CRAWLER EXCAVATOR FROM DEVELON

Develon, formerly Doosan Construction Equipment, has launched the new DX140LC7K

Develon, formerly Doosan Construction Equipment, has launched the new DX140LC-7K 14.6 tonne crawler excavator, replacing the company’s successful DX140LC-7 model.

Whilst the performance and working range are the same as the DX140LC-7, the new machine incorporates many improvements that enhance safety and convenience both for the operator and for working on site, together with a better operator experience, particularly from a maintenance point of view.

The main improvements on the new DX140LC-7K model include:

* Better maintenance access

* Safer access to the upper structure

* Better rear visibility

* Better right-side visibility

* New dashboard with tablet design, offering faster response

The upgraded serviceability of the DX140LC-7K includes better access to the DEF tank and the fuel refilling hose. This is combined with a much easier approach for the operator to the engine compartment via new anti-slip steps and handrails positioned behind the cab. The antislip steps are protected and secured by a new door on the

side of the excavator.

The DX140LC-7K also has a new flattened engine cover design that has reduced the maximum height of cover components on the back of the machine from 1285.5 mm and 1320 mm down to a uniform 1070 mm across all of the back of the machine. This now offers much better visibility for the operator both to the rear and to the right hand side of the machine.

Inside the Engine Compartment

Inside the engine compartment, changes have been made which have facilitated the new lower engine cover, including the repositioning of the PTO (Power take-off) for the rotation pump from the main pump to the engine itself. This has also allowed the size of the aftertreatment system to be optimized and for it to be lowered.

Elsewhere on the DX140LC7K, Develon has removed holding valves from the main valve for better fluidity. These holding valves on the main valve are not needed in the EU, as they are standard on the boom and arm. This reduces pressure losses and creates less heat in the system. The air prefilter has also been moved for better performance and noise

reduction.

Changes within the Operator’s Cab

Inside the operator’s cab, there is a new dashboard monitor with a state-of-the-art tablet design. The former hydraulic two-way pedal has also been replaced by an electronic two-way pedal, with a new PE3C electric pedal as a standard feature, together with a simplified hydraulic system.

The state-of-the-art cab on the DX140LC-7K continues to excel in terms of spaciousness and ergonomics, taking operator comfort and ease of operation to new levels. As well as the new monitor, the operator has a high quality seat and more features as standard than other machines on the market, ensuring super controllability and high precision in all applications.

Other key features in and around the cab include:

* DAB audio (Hands-free calling system and Bluetooth)

* Keyless start (Develon Smart Key) & remote door lock/unlock

* Fully adjustable air suspension seat with heating (with optional cooling function)

* Parallel wiper system and new design pedals

WHEN THE TIME IS RIGHT TO CHANGE A TRACTOR

Landini: When the time is right to change a tractor - choices for renewing your fleet

Tractors have a rather long working life, the duration of which depends on many factors, primarily the level of maintenance and the hours the machine has been in the field. We have talked about the great value of maintenance in several articles. It is essential to take good care of your vehicle, both for better quality and safety of work and so that you do not end up changing parts or having to buy a new model much sooner than expected. That’s why Landini has created Scheduled Maintenance Programmes, designed for the well-being of the machine, the farmer and the business, with a dedicated Landini team

and guaranteed service, for a tractor that always works at high performance.

DISCOVER THE LANDINI SCHEDULED MAINTENANCE PROGRAMME

Added to this is a statistic that is extremely variable depending on the history of the company using the tractor: the hours the tractor has actually worked in the field. As an example, a modern tractor has an average life of 15,000 hours, which is supposed to be completed in 10-15 years. This has changed a lot in the last 20 years, which is why today you can see very different machines

within the same fleet, modern tractors and vehicles that are 30 to 40 years old but still operate well.

This is because for a long time the agricultural sector has been characterised by a high ageing rate and only in recent years has it caught up with other sectors by innovating technology on machines and halving their weight. The target audience has also changed, seeing fewer and fewer small companies in favour of more structured agricultural businesses, with greater demands for state-of-the-art machinery fleets.

TRANSPORT AND MACHINERY SAFETYIMPORTANCE OF MAINTENANCE

Transport and machinery are the biggest contributor to the high fatality rate the agriculture endures

Transport and machinery are the biggest contributor to the high fatality rate that agriculture endures. Here are some simple ways you can reduce the risk and keep you, and others, safe.

One of the easiest ways of keeping yourself safe is by ensuring all the equipment you require is properly maintained and therefore suitable for the intended tasks. This can apply to any piece of equipment you run, for instance tractors, trailers, ATVs, towed appliances, farm vehicles, handheld machines etc.

Daily and regular checks

By completing daily checks before commencing use of the machine or vehicle, you are more likely to notice any possible defects that could prevent the task being carried out safely.

In addition to this, regular maintenance checks completed by a dealership are also recommended to ensure any defects that are not highlighted on daily checks are addressed. This can ensure that small issues are repaired before they escalate and have a bigger financial and safety impact.

Maintenance. Why you should care.

Ensuring your machines and transport are well maintained will also ensure it is running efficiently and therefore likely to reduce long term costs associated with the machine, while also having the potential to increase its longevity.

A well-maintained vehicle or machine is more likely to be complaint with what is considered roadworthy. As such, if an incident should occur (that is not your fault), you are likely to be in a more favourable position if your vehicle or machine is well maintained.

Multi Industrial Doors Ltd is a family owned company founded back in 1985. We pride ourselves on providing a top quality service at an affordable price.

ADAMA BOLSTERS AGRONOMY TEAM WITH NEW APPOINTMENTS

Develon, formerly Doosan Construction Equipment, has launched the new DX140LC7K

ADAMA Agricultural Solutions UK Ltd. has bolstered its agronomy team with the appointment of a new senior agronomy manager, a new regional agronomy manager and a regional field support officer.

David Griffiths joins ADAMA as Senior Agronomy Manager for the West and South of England and Ireland where he’ll be responsible for liaising with senior distribution figures, leading agronomists, and key influencers to increase demand for and understanding of the company’s wide range of crop protection products.

Alexandria Bell has joined ADAMA as a Regional Agronomy Manager and will provide technical support and advice to growers, agronomists and trade partners in the North East of England to ensure they are able to realise the maximum value and efficacy from ADAMA’s portfolio of crop protection products.

Meanwhile, Matt Welton, who has spent the last 12 months working for ADAMA as a supporting regional agronomy manager (on a 12-month contract from Management Development Services (MDS) Ltd.), joins the ADAMA agronomy team as Regional Field Support for the North West and as project manager for ADAMA’s interest in biological crop protection products.

David Griffiths’ interest in

agriculture stems from time spent helping on friends’ farms and subsequently developed into fulltime farm work and tractor driving for a large arable and forage contractor in Worcester. His progression into agronomy came when he joined the Hutchinsons Foundation training programme where he obtained his BASIS and FACTS qualifications. David subsequently returned to a farm management role, taking responsibility for the day-today running of a 1,000-acre arable unit in Worcester whilst also retaining a small amount of independent agronomy work. He then moved into a national sales manager role for a crop nutrition company before joining BASF as an agronomy manager in 2019, providing technical support to growers and agronomists in the west of the UK. During this time, he obtained a full BASIS Diploma and also gained experience as an account manager in the turf and amenity sector.

Alexandria Bell grew up as a farmer’s daughter in Deeside, Scotland and has always had a passion for farming. She studied for an HND in agriculture and specialised field crops at The Scottish Agricultural College (predecessor to SRUC) and is BASIS qualified in horticultural and amenity sector agronomy, and is currently studying for her combinable crops qualification.

Alexandria has a total of 14 years’ experience in the fresh produce sector and started her

agronomy career with Angus Soft Fruits Ltd., working in Spain and Morocco where she spent four winter seasons specialising in the soft fruit, edible crop and top fruit sector. Immediately prior to joining ADAMA she worked as a technical specialist for Biobest Sustainable Crop Management and then as a category technologist for International Procurement and Logistics (IPL) as part of the ASDA Group’s Farm to Fork.

Commenting on the new appointments, ADAMA’s Marketing and Technical Director, Stephen Beal, said:

“I’m delighted to welcome David, Alexandria, and Matt to ADAMA’s UK team where they’ll play an important role in promoting a better understanding of our extensive range of fungicides, herbicides, plant growth regulators, molluscicides and insecticides.

“ADAMA has some ambitious goals over the next five years as we roll out a pipeline of new crop protection products and I look forward to working closely with our new agronomy specialists to help launch these products to customers, distributors, agronomists and growers throughout the UK.”

ADAMA is also recruiting for Regional Agronomy Managers in the South West and South East of England: for more information visit https://www.adama.com/ uk/en/work-with-us/openpositions

UK MUST LEAD EU ON PRECISION BREEDING

The British Society of Plant Breeders has urged the UK Government to ensure Britain retails its leading edge over the rest of Europe

The British Society of Plant Breeders (BSPB) has urged the UK Government to ensure Britain retains its leading edge over the rest of Europe by further promoting the research, investment and innovation of precision breeding.

“The EU Commission’s proposals for regulating the products of New Genomic Techniques (NGTs) in the European Union potentially threaten the UK’s opportunity to take advantage of the recently passed precision breeding bill.

We must remove the barriers that stand in the way of the UK benefiting from this legislation before Europe chooses to embrace it too,” explains BSPB, CEO, Sam Brooke.

The EU has proposed two distinct pathways for NGT plants to be placed on the market. NGT plants that could occur naturally or through conventional breeding would be regulated in the same way as conventional plants and seeds, with no separate statutory requirement for risk assessment, food and feed marketing authorisation, traceability, food labelling or coexistence arrangements. Other NGT plants would be subject to the EU’s existing GMO regulations.

“Simplified field trial arrangements introduced in March 2023 led to an increase in research activity, with eight new field trials of precision bred crops notified in England under the new arrangements, twice as many as the entire EU-27 over the same period. We need to move to support this, not choke it,” adds Mrs Brooke.

The field trials demonstrated that precision breeding techniques provide the potential for plant scientists, breeders and farmers to keep pace with demands for increased agricultural productivity and resourceuse efficiency, healthier food, reduced chemical use, and resilience to climate change. However, a clear route to market is needed to realise these benefits.

Through the Precision Breeding Act, the UK Government led the way in diverging from outdated EU rules classifying gene edited products in the same way as GMOs. But the detail of how the Act’s provisions will be implemented is not yet finalised, particularly in relation to food and feed marketing.

“Based on the Commission’s proposals, there is a real risk that the EU could be on course to eclipse our lead,

by regulating NGT products – where they could have occurred naturally or through conventional breeding – in the same way as conventionally bred varieties. The Food Standards Agency (FSA) is looking to establish an entirely separate regulatory process for precision bred food and feed products, potentially involving expert committee scrutiny, risk assessment, public consultation, parliamentary approval and Secretary of State sign-off. That could significantly drive up the red tape, time and costs involved in bringing new precision bred crops to market,” she says.

“BSPB urges UK Ministers, and the Food Standards Agency in particular, to ensure implementing arrangements for the Precision Breeding Act are as streamlined as possible, and reflect the overwhelming scientific evidence that precision bred products are at least as safe as their conventionally bred counterparts,” she concludes.

IAN FORMAN - NSTS MANAGER

Ian Forman, NSTS manager

Fertiliser prices continue to remain high, which makes it ever more important to ensure accurate application of fertilisers again this season. Think about all of the factors that affect spreading, weather and field conditions, operator training and making best use of the technology available all have an impact on accuracy, but with time constraints some of these aspects may get overlooked.

accurately your machine is set up.

Knowing your machine is in good condition and set up correctly is a good starting point and something that can be easily managed both before and during spreading operations.

cases is achievable.

Having a correctly set up machine will also help you meet obligations to protect the environment. NVZ rules and Farming Rules for Water requires farmers to apply fertiliser as accurately as possible to reduce the risk of pollution. Including a border spreading check when having a spreader tested will help meet these requirements, especially when spreading near watercourses.

SPRAYERS

Advice from AHDB last year suggested in some cases a 20% reduction from RB209 recommended rates for machines not set up accurately. With prevailing high prices this year, and perhaps without the benefit of having some fertiliser left in the shed from 2021 when prices were much cheaper, this should be considered if you don’t know how

Included as part of an NSTS spreader test is a check over the whole machine, paying close attention to the condition of the vanes and agitators. Each product is tested for weight, size and hardness to allow an accurate comparison against manufacturers recommendations for setting up a machine, and adjusted accordingly.

Trays are then laid out across the full width of spread to gain a figure for coefficient of variation (CV). A result of a CV less than 10% is aimed for and in most

For further information, contact NSTS, or go to the website, www. nsts.org.uk where you can search for a Test Centre near you and arrange a test on your machine to ensure it is applying all your fertiliser products on target and evenly across the field.

THE LATEST TRADE AGREEMENT IS THE HEIGHT OF DOUBLE STANDARDS

We are working with the RSPCA and Compassion in World Farming to hold the UK Government to account for sacrificing animal welfare principles

By Mark Williams, chief executive, British Egg Industry Council

As we have in the past on trade related matters, we are working with the RSPCA and Compassion in World Farming to hold the UK Government to account for sacrificing its animal welfare principles in pursuit of free trade agreements. I am referring of course to the decision to exclude eggs/ egg products as a sensitive sector in the recently agreed Comprehensive and Progressive Agreement for Trans-Pacific Partnership (CPTPP). This is even though countries such as Mexico (within the CPTPP block) have an egg sector much larger than that of the UK, or any EU country, but use almost exclusively barrenbattery cage systems that have been illegal in the UK and the EU since 2012. Indeed, even today certain Conservative MPs and government ministers have referenced the fact that we have some of highest laying hen welfare standards in the world, particularly when exploring the idea of banning enriched cages. This is the height of double standards, as you cannot increase animal welfare standards at home, then open your door to products from production systems that are illegal here.

The BEIC responded to the Migration Advisory Committee (MAC) and their call for evidence into the roles currently being filled largely by migrant workers, their salaries, and the implication

of any changes proposed by the UK Government. This is largely a continuation of a call for evidence that MAC ran back in September 2020. Overall, the situation has not improved, and in some circumstances, things are much worse. The British egg industry has been struggling to find staff for key roles, such as catchers. The use of Technology can only achieve so much and even efforts to increase automation in the sector cannot replace roles that are essential to protect for farm animal welfare – the UK Government’s current policy approach to migrant workers is putting animal welfare at risk. On-farm roles have been a challenge to fill, but also many off-farm roles including those in packing centres, and even longdistance / heavy goods vehicle drivers.

The All-Party Parliamentary Group for Eggs, Pigs and Poultry, that the BEIC holds the Secretariat for, recently hosted a panel discussion in Westminster to discuss disease preparedness, safeguarding the UK’s food security. Lord Benyon, Minister of State for Biosecurity, Marine and Rural Affairs attended the panel, which I was part of. Jim Shannon MP, as Chair of the APPG, opened the event by saying “To live in a fully functioning, capable, and robust nation, food security is a completely non-negotiable attribute”, and later went to acknowledge that “Disease outbreaks are becoming more frequent, and more severe, not just in the UK but elsewhere in the world”. This has significant

impact on the food supply chain, with catastrophic consequences for farmers. It isn’t confined to farm animals, these diseases spread into the wild animal population, wreaking havoc on our natural eco-systems”.

The event was well attended by members of both the House of Commons and House of Lords. I hope that the work of the APPG will demonstrate how important food security is to everyone and that the parliamentarians that attended will play their part in ensuring the UK Government acts and makes the necessary reforms to better prepare for future disease threats – particularly around AI vaccination.

In the EU, the European Commission is to amend the EU marketing legislation as early as this Autumn to remove reference to the 16-week period whereby FR eggs can maintain their status when FR poultry flocks are required to be housed to protect them against a Notifiable Avian Disease. The British egg industry’s recent experience with AI, the housing order, and the BEIC labelling solution has only served to reinforce the BEIC’s position that the UK Government and devolved governments must follow suit. To help expediate the process, Defra have confirmed that a GB-wide consultation will take place shortly along the same lines. This means that there would be no clock start and FR hens could remain housed until it was safe for them to come out again without loss of FR egg status.

‘LAST YEAR’S HOT WEATHER IS A WARNING OF THINGS TO COME’

By Matt Donald pig & poultry farmer, North Yorkshire

Is the recent spell of hot weather a warning of things to come throughout summer? Mirroring last year, crops are starting to look thirsty, grass isn’t growing and the chickens are as warm as they wish to be, and it is only midJune.

Last years highs of 40 degrees may be around the corner and we need to ensure we are prepared and ventilation is working at its full potential.

Previously poultry has not really been included within grant schemes coming from the government, however it would be nice to see cooling systems on any future options as well as anything that enhances biosecurity.

The warm temperatures do have some benefits, we are seeing our latest breeder

flock fly into lay and exceeding 80% production before their

We do have to remember it is a marathon to get to 60 weeks, the birds will need to perform strongly all the way through to hit that 160 chicks per bird we hope for. The warmer atmosphere also means we can get away with peaking feed two grams lower than we would in winter. It does not sound a lot, but at today’s prices every gram matters.

birthday which is an excellent figure so early in the flock. Numerous factors such as good rearing contribute to this, but we also think the warm spring weather is having a positive effect, even in a controlled environment. Although the early small eggs are of no use to the hatchery, because of numbers we still have over 70% making the weight grade at this stage.

It is disappointing to hear of further price cuts in the poultry meat independent sector, costs may have fallen from the highs last year, but many farms are still caught up in older feed and energy contracts. This combined with increasing interest, labour and repair bills, I speak to many producers questioning why they should continue.

IN DEPTH: TURKEY REALITY STARTS TO BITE

The planned closure of a turkey processing plant in Wales is bad news for the turkey industry

The announcement by Avara Foods that it is planning to shut its Abergavenny factory in autumn 2023, which would result in the loss of all jobs at the site, does not bode well.

The Abergavenny facility was part of the acquisition of turkey processor Cranberry Foods by Faccenda, in 2012. Faccenda then went on to form Avara Foods in 2018 in a joint venture with Cargill. It is a ‘cut and pack’ operation, predominantly preparing a range of fresh turkey products, alongside some chicken lines, for retail customers.

The closure – if it goes ahead – will mean turkey farms in the region will be repurposed – some for chicken, others for pullets. The news is a sign of the times. Apart from the premium, specialist market, selling turkey in Britain is currently a recipe for big losses.

The big players are wrestling with the impact on their finances. Bernard Matthews Foods Limited reported an annual loss after tax of £20.9 million in the year to 2 January 2022, a significantly bigger loss than the previous year when the company reported a £3.95 million loss. Higher costs and a shortage of labour were key factors, the company said. Moy Park

made the decision to exit the turkey market altogether in the past few years.

Poor demand

Demand for turkey has fallen significantly at retail in response to rising prices. Sales of turkey by volume in UK supermarkets were down 23.4% year on year in the 12 weeks ending 19 March, according to Kantar data. Average prices were up 16.4%. It seems clear consumers cannot stomach such price rises.

While chicken prices were also up on average 16% during the same period, the price per kilo was £4.60 for chicken, while turkey cost significantly more at £6.56 per kilo for turkey or £9.80 for turkey breast.

Avara Foods said it was facing significant inflationary pressure in fuel, commodities and labour, which has driven up prices and significantly reduced demand for UKproduced turkey in the retail market. This has led to the decision to restructure its turkey business to operate “a more efficient operational footprint focused on fewer, better invested facilities,” it said.

“Over the past six months the company has looked in depth at a range of options

to enable its wider business to compete effectively in the market in the future. Regretfully, this process identified that volumes could be processed more efficiently in other operations and with lower capital investment,” said a spokesman. “This has resulted in the proposal to close the Abergavenny site. This difficult decision has not been taken lightly and in no way reflects on the hardworking colleagues.”

The company is currently working through a consultation process with the people affected by this proposal, but said it was important to say no final decisions had been taken. “The nature of this consultation means that no final decisions have been made and there will be no speculation as to how the process will conclude,” the spokesman said.

Non-existent rewards

Turkey has always been a tricker part of the market to make work than chicken, but a series of events over the past few years has pushed the market into crisis, with losses mounting, and according to one source, companies only continuing to grow it out of a sense of duty to the retailers.

STEVE BIRCHALL: KEEPING IT IN THE FAMILY

Testimonial: This testimonial is supplied by P.R Starkie, Farm Manager at P.M. Ashburner Ltd

Being a small family run Poultry unit we need to have good reliable contractors to ensure our site has a good state of cleanliness and biosecurity.In order to achieve this we use another family run business, Steve Birchall Poultry Services Ltd.

As a business we have worked in relationship with Steve Birchall and his team for a long number of years and will continue to do so for many more. His team do a first class job washing and disinfecting our site. Nothing is too much trouble and they can accomodate our needs at the drop of a hat.

I can honestly say Steve and his team are excellent, reliable, thorough, tidy and hard working. They leave our site ready for action! I would recommend Steve Birchall Poultry Services without hesitation.

P.R

Starkie Farm Manager

P.M Ashburner Ltd

Testimonial from W. Bateman & Co

I would highly recommend Steve Birchall Poultry Cleaning Services, having knowing him for over 25 years and it has been an absolute pleasure to have him as my loyal customer and I look forward to many more years in business and wish Steve Birchall the continued success with his business and the good reputation he has gained over the years. We look forward to many more years in business with Steve Birchall.

All the best - All at W Bateman & Co

The complete management system for the Gemini milking robot!

Cow Performance Robot Performance

Management Tools

Data Interface

Herd Performance

Gemini OneView is a complete management system for the Gemini milking robot that transforms all your herd information into easy-to-use decision-making tools. While entering the main dashboard, you are given the ability to instantly monitor all your important production and cow information, in real time.

Let the data talk ! DATA INTERFACE

It all starts with the OneView dashboard, which is a powerful and visually easy tool to interpret for monitoring your dairy farm! Stay connected and monitor your milking system continuously, on any device.

Accurate data are always available, customized to your needs Also, the OneView management system can connect to third party management systems. This means you have all possible information centralized into one convenient system.

As if your robot could talk !

ROBOT PERFORMANCE

Receive alerts in real time, so all stakeholders have insight to resolve critical alerts when necessary.

The analyses enables you to adapt and optimize the system to your management goals!

• Milking analyses

• Feeding analyses: to help you to implement the ideal herd feeding performance

As if your herd could talk !

HERD PERFORMANCE

All herd information translated into easy to take decision tools.

• Herd production indicators,

• Herd health indicators,

• Activity measurement,

• Herd traffic indicators,

• Herd lifetime indicators,

• Herd routines,

• Herd feeding indicators.

Run your farm the way you want !

MANAGEMENT TOOLS

Numerous management tools combined to run your farm according to your needs and goals. Set up the system based on your preferences and optimize where needed.

•Sorting engine: flexible and smart selection with almost endeless possibilities.

•Feeding: tune your feeding system the way you want. Input all your feeding rations and tables, according to the feeding management you wish to apply.

•Sensorics tools: as if milk could talk!

The sensors transfer any information you need, such as milk flow, somatic cell count, colour and conductivity.

Davison & Axup

Dairy Supplies, Swiss Cottage, Bardney Road, Wragby, Market Rasen, LN8 5QZ

As if your cow could talk !

COW PERFORMANCE

A large range of cow performance indicators help you manage your dairy farm to your preference.

• Cow production indicators;

• Cow health indicators,

• Conductivity,

• Cow lifetime indicators,

David Johnson (Lutt) Ltd - Upper Bruntington Ind Est, Leicester, LE17 5QZ | t: 01162 478349

David Johnson (Lutt) Ltd, Upper Bruntingthrope Ind Est.

Electro-Mech Agri Ltd, 7 Tulnagall Road, Donaghmore, Dungannon

Davison & Axup - Swiss Cottage, Market Rasen, LN8 5QZ | t: 01673 858567

Electro-mech Agri - Tulnagall Rd, Dungannon, BT70 3LR | t: 02887 767376

BT70 3LR

Milkflo - Trengove Farm, Redruth, TR16 4PU | t: 08450 944 815

Milkflo Dairy Systems Ltd, Trengove Farm Cot Road, Redruth Cornwall, TR16 4PS

t: 01673 858567

Leicester, LE17 5QZ

t: 01162 478349

t: 02827767376

Wessex Farm - Mill Road, Somerset, TA10 9DJ | t: 01458 252566

www.electromech. com

t: 08450 944815

www.milkflouk.com

• Cow routines. BouMatic.com

In the end the milk quality analysis informs you on your management performance and helps you to adjust when needed.

Bob Gerard Ltd

22 London Road, Great Glen, Leicester, LE8 9GF t: 01162592224

www.bobgerard.co.uk

DJ Leigh

Near Daventry, Northants, NN11 6DP t: 07502 661861

CM Barber Plant Hire

The Depot, Steam Mills, Cinderford, GL14 3JD t: 07774 249580

www.cmbarberplanthire.co.uk

Mikes Graphics

5 Wall St, Hereford, HR4 9HP t: 07855 985649

www.mikesgraphics.co.uk

David Taylor (Garages) Ltd

David Taylor Garages Granada Park Motors, Crickhowell, NP8 1HW t: 01873 564016 | www.davidtaylorgarages-isuzu.co.uk

Southam Agri Fields Farm, Station Rd, Southam, CV47 2DH t: 01926 813426

www.southamagri.co.uk

Steve Birchall Chorley, Lancashire, PR6 3TQ t: 07850 838172

roosterman1@btinternet.com

W Bateman & Co Garstang Rd, Barton Nr Preston, PR3 5AA t: 01772 862948

www.bateman-sellarc.co.uk

Wharfedale Tractors Unit 1 Riffa Bus. Park Harrogate Rd, Otley, LS21 2XB t: 01132 841117 Advertise

DJ Leigh Machinery

DG Buscombe, Saint Columb, TR9 6DE

t: 01637 880119 | www.dgbuscombe.co.uk

Marrs of Methlick, Schoolbrae Garage, Methlick, Ellon, AB41 7DS

t: 01651 806910 | www.marrsofmethlick.com

Smithfield Tractors, Llanelwedd, Builth Wells, Powys, Ls2 3SR

t: 01982 553221 | www.smithfieldtractors.co.uk

Trebor Jones & Son Ltd, Llanfyllin, SY22 5LE

t: 01691 648411

Wharfedale Tractors, Unit 1 Riffa Bus. Park, Harrogate Rd, Otley, LS21 2XB

t: 01132 841117

DJ LEIGH USED

DAVID BROWN 1490 ECON HML £POA

DAVID BROWN 1490 2WD TRACTOR Y REG NEEDS TLC £2375

1968/69 DAVID BROWN 990 LOADER ROLL BAR £2500

IH 144 TRACTOR AND LOADER FORK CAB £1895

1988 KRAMER 312 SE LOADRAD SHOVEL £4500

MUIR HILL 2WD LOADING SHOVEL NEEDS TLC £745

MF 3303 DIGGER LOADER H REG £2750

KUBOTA KH 51 ME £4775

PETTIET TIPPING TRAILER £990

TRAILER SMALL 3 TON WOOD SIDES FLOOR £875

EX ARMY BOMB TRAILER £685

LELY POWER HARROW 3.5M 1000 RPM £845

LELY POWER HARROW 4M 1000 RPM £895

LELY POWER HARROW 4M 540 RPM £2450

VICON CHISEL PLOUGH HEAVY £525

BOMFORD CHISEL PLOUGH £675

MF CHISEL PLOUGH £695

TASKER TILL TRAINDISC/TINES DISK £2890

BOMFORD HEDGE TRIMMER T,P,L £4775

BOMFORD HYDRO MOWER BRACKETS £685

BOMFORD BUSHWALKER TRIMMER NEEDS TLC £520

SPEARHEAD MK6 HEDGE CUTTER T,P,L £POA

ECON HM2 HEDGE TRIMMER BRACKET £1645

BAMFORD 4 FURROW PLOUGH DISC SKIMS £475

DOWDESWELL 4 FURROW REV DP7 £995

DOWDESWELL 4 FURROW REV DP 7D £1690

FERGUSON EARTH SCOOP £245

MF DITCHING BUSKET PLUS DIGGING BUCKET £350

McCONNEL HEDGE CUTTER HEAD £585

BARTON MUCK FORK TO FIT SMALL LOADER £370

BOBCAT MUCK FORKS TO FIT 4FT MACHINES £385

IH 2 FURROW REV PLOUGH NEEDS ONE BOARD £285

BUCKETS TO FIT MF 203/205/ MF50B,50D FROM £220

BUCKETS TO FIT NH MINI DIGGER SMALL/DITCHING £375

MACHINERY

BUCKETS HEAVY DUTY LARGE MACHINE FROM £325

TYRES AND RIMS TO FIT MF/FORD ETC., SIZE 14.0-16 10 PLT £POA

12.5/80-18. 11.00/16 10-00-16SL 8 PLY15.0/70-18 PRICES START AT £170 TO £250

16.5/85-28 ON FORD RIMS 10 PLY £275

MANITOU FORKLIFT MB 26C SERIES 1 NEEDS TLC £1975

SANDERSON 50 FORKLIFT NEEDS TLC £1975

BOBCAT SKID LOADER 533 NEEDS TLC £1025

BOBCAT SKID LOADER 313 NEEDS TLC £2475

TEAGLE 510 TOPPER OFF SET MACHINE £1385

TOYOTA TOP TO FIT SINGLE CAB PICKUP £165

IFOR WILLIAMS 12FT TRAILER WITH SIDES £1745

WOOD BURNER £325

ELDIS 2 BERTH CARAVAN NEEDS TLC £750

SMALL CAMPING TRAILER NEEDS TLC £25

SHELBOURNE REYNOLDS RAPE MACHINE £1790

BOUNCE SNOW PLOUGH £935

TEAGLE FLAIR SHAFT FOR TOPPER £375

GRAYS 3,P,L SNOW PLOUGH £665

TORO GROUNDMASTER MOWER DIESEL £4790

JOHN DEERE RIDE ON MOWER £1380

PARMITER POOST KNOCKER ROPE LIFT £1725

SUTON MUCK FORK NEEDS TLC £225

FOUR DOWEDSWELL SKIMS TO FIT DPI PLOUGH £225

RANSOME SKIMS AND DISCS FROM £70 TO £125

FUEL TANK £155

FOLDING ROLLS 6.3M £2750

OLD STEEL SAW BENCH ON WHEELS NEEDS TLC £138

FOR MORE INFORMATION PLEASE CALL DAVID ON 07876 770545 OR 07502 661861

*All prices are not inclusive of VAT*

BOSS ORV WELCOMES EUROMEC CONTRACTS LTD

Boss ORV has announced they have partnered with Euromec Contracts Ltd to retail Corvus Off-Road Vehicles products in the East Midlands.

BOSS ORV has announced they have partnered with Euromec Contracts Ltd to retail Corvus Off-Road Vehicles’ products in the East Midlands region. Euromec, which dates back to 1997, has developed as industrial cleaning and groundcare equipment specialists. They offer sales and service of scrubber dryers, floor sweepers, lawn mowers, tractors and utility vehicles. Based in Market Harborough, it is a UK company with over twenty-five years of experience in municipal and industrial powered machinery.

As well as becoming a Corvus dealer, they are also official UK dealer for Kubota, Honda

Power Products, STIGA and Mountfield. As partner with some of the world’s leading manufacturers, they say they have a particular pride in sourcing innovative products but emphasise they believe in putting the customer first and providing a full range of aftersales services. Phil Everett, MD at BOSS ORV, the sole UK distributor of Corvus 4x4 utility vehicles, welcomed the company to the Corvus dealer network, now comprising forty-three dealers giving a total of sixty outlets across the UK. He says he’s looking forward to working with Finance Director Maria Griffith, Sales Director Graham Hill, Director Nikki Heighton, Annie Povilionis, and all the Euromec

team to grow the Corvus business in the region. They will sell the complete range of the Corvus Terrain UTVs and accessories from Europe’s first off-road utility vehicle manufacturer.

This includes the professional UTVs, the Terrain DX4, the all-electric EX4 and, coming later in the year, a new midsize model.

For more information about the Corvus Terrain range, you can call 01785 561046 E-mail: sales@bossorv.co.uk Web: www.bossorv.co.uk

MKM AGRICULTURE JOINS THE CAN-AM OFF-ROAD FAMILY

Bombardier Recreational Products (BRP) is continuing to grow its Can-Am off-road dealer network in the UK team.

Bombardier Recreational Products (BRP) is continuing to grow its Can-Am offroad dealer network in the UK with the appointment of Bedford-based MKM Agriculture. This new addition is part of Can-Am offroad’s ongoing expansion plans to increase its share of the utility market in UK, while providing utility users with ATVs and SSVs that are suitable for use across multiple applications and sectors.

A family-run business with over 30 years’ experience in the agriculture and ground care sectors, MKM Agriculture will be adding the Can-Am offroad line-up as part of the business’ ongoing strategy to continually strengthen its product offering through the provision of vehicles its customers are requesting. In addition, it will open new avenues and opportunities for the business’ sales

All BRP’s vehicles are manufactured to a very high standard from the Rotax engines which power them to the innovative designs that improve the handling, comfort, and ease of use when out on the trails or towing or hauling goods and equipment.

Mike Loach, BRP commercial manager UK & Ireland, says, “We’re delighted to be adding such a knowledgeable and experienced dealer to our

growing network in the UK. We believe the company will hit the ground running and we look forward to supporting the business as it helps us expand our share of the market in the utility sector and introduce new users in the region to the versatility, power, and performance the Can-Am off-road lineup offers.”

Anthony Deacon, managing

director, MKM Agriculture Ltd, ads, “Adding the Can-Am off-road line-up aligns with our ethos of investing in quality products that will benefit our customer base.

The combination of the Can-Am offering and our team’s knowledge and experience will enable us to become the ‘go to’ business in the area for anyone looking to purchase an ATV or SSV and we look forward to working with Mike to achieve this.”

MORE NEW DEALERS FOR CORVUS OFFROAD VEHICLES

Alan McCracken ATV services and Roberts Rural are the latest dealers to join the Corvus dealer network.

Alan McCracken

ATV Services and Roberts Rural are the latest dealers to join the Corvus Off-Road Vehicles dealer network. The announcement comes from BOSS ORV, the sole UK distributor of the Corvus UTV range. Allan McCracken started his business twenty-eight years ago following working for another Yamaha dealer. Based in Castle Douglas, the dealership offers sales and service of ATV’s, walk-behind and ride-on mowers in a thirty-mile radius of the 18th century market town.

“We’re delighted to welcome Allan McCracken and his team as our latest dealership appointment in Scotland,” says Phil Everett, BOSS ORV’s Managing Director. “I have known Alan for over twenty-five years and the quality of service he provides is second to none. I’m looking forward to working with Alan again and developing the Corvus brand in this part of South

West Scotland.” The dealership is well known in the region for selling ATV’s but until now had no off-road utility vehicle offering. The Corvus, Alan says, is ideal for the area and he is pleased to put his name behind a such reputable manufacturer.

Chard in Somerset is the home of Roberts Rural, who has become the authorised Corvus dealer of the area. A familyrun business covering the southwest they supply new and used UTV’s including the new Corvus electric

EX4, diesel and petrol range.

“Welcome to Roberts Rural as our new dealer in Somerset,” says Phil Everett. “It’s great to have John Parry and Ed Cousins on board and we’re looking forward to working with them in this important region.” Roberts Rural provides machinery and parts sales, servicing and maintenance to a range of business sectors including Local Authorities, forestry,

groundscare, agriculture, equine and game keeping.

They will provide Corvus with coverage across Somerset, Devon and Dorset.

For more information about the Corvus Terrain range, you can call 01597 810188

BUILT STRONG WORK HARD TO

The MULE PRO-DX offers a class-leading 453kg capacity low tipping cargo bed and 907kg towing potential.

High torque diesel power moves cargo and crew quickly with the safety assurance of the Roll-Over Protection Systems (ROPS).

THE CHOICE OF PROFESSIONALS

D. H. Wadsworth & Sons Flockton Tel: 01924 840319

D. H. Wadsworth & Sons Malton Tel: 01653 692244

WWW.WADSWORTHQUADS.CO.UK

FOR MORE INFORMATION, CONTACT YOUR LOCAL DEALER:

DAY & COLES AGRICULTURAL

Wellingboro ugh, NN8 6UW Tel 01933 673900

www.dayandcoles.co.uk

JIM P RICE M ACHINE RY LTD

Craven Arms SY7 9QG Tel 01588 673 746

www.jimpricemachinery.com

MARTIN PEARS ENGINEERING LTD

Totnes TQ9 7JE

Tel 01548 521 429

www.mpearsengineering.co.uk

SOUTHAM A GRI SE RVICES

➢ Powerful 993cc Diesel engine

➢ 2WD or 4WD modes

➢ Largest cargo bed in class

➢ Gas-assisted tilting cargo bed

➢ Stable, wide-body chassis

➢ 907kg towing capacity

Southam CV47 2DH Tel 01926 813 425

www.southamagri.co.uk

ATVTRAC - PROVEN IN THE FIGHT AGAINST RURAL CRIME

As farmers and landowners continue to fight the threat of rural crime, ATVTrac offers a line of defence

As farmers and landowners continue to fight the threat of rural crime, ATVTrac offers a proven and effective line of defence.

With multi-tier technology, ATVTrac offers real-time location information, using GPS, GPRS, GSM and RF technology to not only pinpoint vehicle location, but to inform owners of unauthorised movement via text, email and phone call.

With a 98% recovery rate and an

average recovery time of three hours, ATVTrac’s results speak for themselves, with additional features too.

ATVTrac’s extra features are designed to make life easier and safer, with live tracking and machine over, assisting with safety and duty of care, covering lone worker polices in the process.

On top of great safety features, ATVTrac offers other useful functions such as live battery information, with adjustable low-

Revolutionising ATV & Asset Security

level notifications and an all-new service notification facility, helping to keep track of oil changes and routine maintenance.

And if the unthinkable happens, the true benefit of ATVTrac’s service becomes apparent, thanks to the 24hr manned call centre, which tracks the device, directly liaising with police or Securitas for recovery, to recover the asset.

Preferential insurance rates available too. Find out more at www.atvtrac.co.uk

SUBARU OUTBACK. BUILT FOR

ADVENTURE.

With AWD off-road capability, proven reliability and advanced safety features, the all-new Subaru Outback is the next generation of adventure.

FROM £36,990

438 Tester

438 Tester, 438 Tester, 438 Tester 438 Tester Tel: 438 Tester

Search Subaru

Award-winning

• 2.5i Boxer Engine Lineartronic

• Permanent Symmetrical

• EyeSight Safety Package

• Driver Monitoring System

• X-MODE with Hill Descent

• Apple CarPlay™ & Android

• 2,000kg Towing Capacity

SUBARU OUTBACK fuel economy and CO2 results (WLTP): Combined 33.0mpg, CO2 emissions 193g/km. MPG figures are official EU test figures number of factors including accessories fitted (post-registration), variations in weather, driving styles & vehicle load. *3 services from £299.00 (incl. VAT) service intervals - either 12,000 miles or 12 months, whichever comes sooner. All services must be completed by an authorised Subaru Retailer. The only. Does not cover any non-service related parts or repairs or general wear and tear. Servicing is transferable with the vehicle. Offers may be varied

Vehicle shown is an Outback 2.5i Limited Lineartronic, OTR price of £37,440.00. Model shown price includes optional special paint finish at £595.00.

Dales Subaru, Barnoldswick, Lancashire, BB18 6TG

t: 01282 797555

www.dales-subaru. co.uk

Perkins Garage, Braintree, CM77 6SA t: 01376 550899

www.perkinsgarages. co.uk

Jeffries of Bacton, Stowmarket, IP14 4HP t: 01449 781131

www.jeffriesofbacton. co.uk

3 YEARS SERVICING FOR £299*

Award-winning features. Fitted as standard.

Lineartronic

Symmetrical All-Wheel Drive

Package System

Descent Control

Android Auto™

Capacity (braked)

• 213mm Ground Clearance

• 11.6" Tablet-like Infotainment System

• Heated Front and Rear Seats

• Dual-Zone Automatic Air Con

• Adaptive Driving Beam

• LED Headlights

• Reversing Camera

figures for comparative purposes & may not reflect real driving results. Fuel consumption achieved in real life conditions & CO2 produced depends on a VAT) offer applicable when you purchase a brand-new Subaru Forester e-BOXER, XV e-BOXER or Outback. All services should be taken at the relevant The customer’s failure to redeem the services within the designated mileage or time will void the manufacturer’s warranty. Available to retail customer varied or withdrawn at any time. Offer ends 30.06.23.

£595.00.