Column Formwork KS Xlife - 2014

999746002 - 02/2014 en-GB

The Formwork Experts.

Column formwork KS Xlife User Information Instructions for assembly and use (Method statement)

9746-300-01

Introduction

User Information Column formwork KS Xlife

tion Introduc-

© by Doka Industrie GmbH, A-3300 Amstetten 2

999746002 - 02/2014

User Information Column formwork KS Xlife

Introduction

Contents 4 4 7 8 10 11 12 16 18 20 21 22

35

Introduction Elementary safety warnings Eurocodes at Doka Doka services Product description Areas of use Assembling the column formwork Erecting and stripping the formwork Resetting Changing the column cross-section Plumbing accessories Platform configurations with Platform planking KS Ladder system XS with Platform planking KS Platform configurations with Doka column formwork platform 150/90cm Ladder system XS on Doka column formwork platform 150/90cm Transporting, stacking and storing

40

Component overview

23 26 31

999746002 - 02/2014

3

Introduction

User Information Column formwork KS Xlife

Elementary safety warnings Introduction

User target groups

Remarks on this document

▪ This manual is aimed at all persons who will be work-

▪ This manual can also be used as a generic method

▪ ▪

▪

▪

ing with the Doka product or system that it describes.

It contains information on the standard design for setting up this system, and on correct, compliant utilisation of the system.

All persons working with the product described herein must be familiar with the contents of this manual and with all the safety instructions it contains.

Persons who are incapable of reading and understanding this booklet, or who can do so only with difficulty, must be instructed and trained by the customer.

The customer is to ensure that the information materials provided by Doka (e.g. User Information booklets, Instructions for Assembly and Use, Operating Instruction manuals, plans etc.) are available to all users, and that they have been made aware of them and have easy access to them at the usage location.

In the relevant technical documentation and formwork utilisation plans, Doka shows the workplace safety precautions that are necessary in order to use the Doka products safely in the usage situations shown.

In all cases, users are obliged to ensure compliance with national laws, Standards and rules throughout the entire project and to take appropriate additional or alternative workplace safety precautions where necessary.

▪

▪

statement or incorporated with a site-specific method statement.

Many of the illustrations in this booklet show the situation during formwork assembly and are therefore not always complete from the safety point of view.

Any safety accessories not shown in these illustrations must still be used by the customer, in accordance with the applicable rules and regulations.

Further safety instructions, especially warnings, will be found in the individual sections of this document!

Planning ▪ Provide safe workplaces for those using the form-

▪

work (e.g. for when it is being erected/dismantled, modified or repositioned etc). It must be possible to get to and from these workplaces via safe access routes!

If you are considering any deviation from the details and instructions given in this booklet, or any application which goes beyond those described in the booklet, then revised static calculations must be produced for checking, as well as supplementary assembly instructions.

Hazard assessment

Regulations; industrial safety

▪ The customer is responsible for drawing up, docu-

▪ All laws, Standards, industrial safety regulations and

menting, implementing and continually updating a hazard assessment at every job-site.

This document serves as the basis for the site-specific hazard assessment, and for the instructions given to users on how to prepare and utilise the system. It does not substitute for these, however.

4

▪

other safety rules applying to the utilisation of our products in the country and/or region in which you are operating must be observed at all times.

If a person or object falls against, or into, the sideguard component and/or any of its accessories, the component affected may only continue in use after it has been inspected and passed by an expert.

999746002 - 02/2014

User Information Column formwork KS Xlife

Rules applying during all phases of the assignment

Introduction

Assembly ▪ The equipment/system must be inspected by the

▪ The customer must ensure that this product is

▪

▪ ▪

▪

▪

▪

▪

erected and dismantled, reset and generally used for its intended purpose in accordance with the applicable laws, Standards and rules, under the direction and supervision of suitably skilled persons. These persons' mental and physical capacity must not in any way be impaired by alcohol, medicines or drugs.

Doka products are technical working appliances which are intended for industrial/commercial use only, always in accordance with the respective Doka User Information booklets or other technical documentation authored by Doka.

The stability of all components and units must be ensured during all phases of the construction work!

The functional/technical instructions, safety warnings and loading data must all be strictly observed and complied with. Failure to do so can cause accidents and severe (even life-threatening) damage to health, as well as very great material damage.

Fire-sources are not permitted anywhere near the formwork. Heating appliances are only allowed if properly and expertly used, and set up a safe distance away from the formwork.

The work must take account of the weather conditions (e.g. risk of slippage). In extreme weather, steps must be taken in good time to safeguard the equipment, and the immediate vicinity of the equipment, and to protect employees.

All connections must be checked regularly to ensure that they still fit properly and are functioning correctly.

It is very important to check all screw-type connections and wedge-clamped joins whenever the construction operations require (particularly after exceptional events such as storms), and to tighten them if necessary.

It is strictly forbidden to weld Doka products – in particular anchoring/tying components, suspension components, connector components and castings etc. – or otherwise subject them to heating.

Welding causes serious change in the microstructure of the materials from which these components are made. This leads to a dramatic drop in the failure load, representing a very great risk to safety.

The only articles which are allowed to be welded are those for which the Doka literature expressly points out that welding is permitted.

999746002 - 02/2014

▪

▪

▪

customer before use, to ensure that it is in suitable condition. Steps must be taken to rule out the use of any components that are damaged, deformed, or weakened due to wear, corrosion or rot.

Combining our formwork systems with those of other manufacturers could be dangerous, risking damage to both health and property. If you intend to combine different systems, please contact Doka for advice first.

The equipment/system must be assembled and erected in accordance with the applicable laws, Standards and rules by suitably skilled personnel of the customer's, having regard to any and all required safety inspections.

It is not permitted to modify Doka products; any such modifications constitute a safety risk.

Closing the formwork ▪ Doka products and systems must be set up so that all loads acting upon them are safely transferred!

Pouring ▪ Do not exceed the permitted fresh-concrete pres-

sures. Over-high pouring rates overload the formwork, cause greater deflection and risk breakage.

Stripping out the formwork ▪ Do not strip out the formwork until the concrete has

▪

▪

reached sufficient strength and the person in charge has given the order for the formwork to be stripped out!

When stripping out the formwork, never use the crane to break concrete cohesion. Use suitable tools such as timber wedges, special pry-bars or system features such as Framax stripping corners.

When stripping out the formwork, do not endanger the stability of any part of the structure, or of any scaffolding, platforms or formwork that is still in place!

5

Introduction

Transporting, stacking and storing ▪ Observe all regulations applying to the handling of

▪ ▪

formwork and scaffolding. In addition, the Doka slinging means must be used - this is a mandatory requirement.

Remove any loose parts or fix them in place so that they cannot be dislodged or fall free!

All components must be stored safely, following all the special Doka instructions given in the relevant sections of this manual!

Maintenance

User Information Column formwork KS Xlife

Symbols used The following symbols are used in this booklet:

☞

Important note Failure to observe this may lead to malfunction or damage.

CAUTION / WARNING / DANGER Failure to observe this may lead to material damage, and to injury to health which may range up to the severe or even life-threatening.

▪ Only original Doka components may be used as

spare parts. Repairs may only be carried out by the manufacturer or authorised facilities.

Miscellaneous We reserve the right to make alterations in the interests of technical progress.

Instruction This symbol indicates that actions need to be taken by the user.

Sight-check Indicates that you need to do a sight-check to make sure that necessary actions have been carried out.

Tip Points out useful practical tips.

Reference Refers to other documents and materials.

6

999746002 - 02/2014

User Information Column formwork KS Xlife

Introduction

Eurocodes at Doka In Europe, a uniform series of Standards known as Eurocodes (EC) was developed for the construction field by the end of 2007. These are intended to provide a uniform basis, valid throughout Europe, for product specifications, tenders and mathematical verification.

The EC are the world's most highly developed Standards in the construction field.

In the Doka Group, the EC are to be used as standard from the end of 2008. They will thus supersede the DIN norms as the "Doka standard" for product design.

Ed Ed

Fd

Fk

F

Design value of effect of actions (E ... effect; d ... design) Internal forces from action Fd (VEd, NEd, MEd) Design value of an action Fd = F · Fk (F ... force) Characteristic value of an action "actual load", service load (k ... characteristic) e.g. dead weight, live load, concrete pressure, wind Partial factor for actions (in terms of load; F ... force) e.g. for dead weight, live load, concrete pressure, wind Values from EN 12812

Comparison of the safety concepts (example) Permissible stress design 115.5 [kN]

Fyield

EC/DIN concept Rk

115.5 [kN]

Rd gM = 1.1

90<105 [kN] n ~ 1.65

Factual

A

98013-100

60 [kN]

gF = 1.5

Fpermissible

98013-102

60<70 [kN]

A

Ed

90 [kN]

Factual Fpermissible

The widely used "Permissible stress design" (comparing the actual stresses with the permissible stresses) has been superseded by a new safety concept in the EC. The EC contrast the actions (loads) with the resistance (capacity). The previous safety factor in the permissible stresses is now divided into several partial factors. The safety level remains the same!

Rd Rd

Design value of the resistance (R ... resistance; d ... design) Design capacity of cross-section (VRd, NRd, MRd) Rk Rk Timber: Rd = kmod · Steel: Rd = M M

Rk

Characteristic value of the resistance e.g. moment resistance to yield stress

M

Partial factor for a material property (in terms of material; M...material) e.g. for steel or timber Values from EN 12812

kmod

Modification factor (only for timber – to take account of the moisture and the duration of load action) e.g. for Doka beam H20 Values as given in EN 1995-1-1 and EN 13377 The "permissible values" communicated in Doka documents (e.g.: Qpermissible = 70 kN) do not correspond to the design values (e.g.: VRd = 105 kN)! ➤ Avoid any confusion between the two! ➤ Our documents will continue to state the permissible values.

Allowance has been made for the following partial factors: F = 1.5 M, timber = 1.3 M, steel = 1.1 kmod = 0.9 In this way, all the design values needed in an EC design calculation can be ascertained from the permissible values.

Ed Rd

A Utilisation factor

999746002 - 02/2014

7

Introduction

User Information Column formwork KS Xlife

Doka services Support in every stage of the project Doka offers a broad spectrum of services, all with a single aim: to help you succeed on the site.

Every project is unique. Nevertheless, there is one thing that all construction projects have in common – and that is a basic structure with five stages. We at Doka know our clients' varying requirements. With our consulting, planning and other services, we help you achieve effective implementation of your formwork assignment using our formwork products – in every one of these stages.

1 Project Development Stage

2 Bidding Stage

3 Project Management Planning Stage

Taking well-founded decisions thanks to professional advice and consulting

Optimising the preliminary work with Doka as an experienced partner

Controlled, regular forming operations, for greater efficiency resulting from realistically calculated formwork concepts

Find precisely the right formwork solutions, with the aid of ▪ help with the bid invitation ▪ in-depth analysis of the initial situation ▪ objective evaluation of the planning, execution, and time-risks

Draw up potentially winning bids, by ▪ basing them on realistically calculated guideline prices ▪ making the right formwork choices ▪ having an optimum time-calculation basis

Plan cost-effectively right from the outset, thanks to ▪ detailed offers ▪ determination of the commissioning quantities ▪ co-ordination of lead-times and handover deadlines

8

999746002 - 02/2014

User Information Column formwork KS Xlife

4 Concrete Construction Stage

Introduction

5 Project Close-out Stage

The advantages for you thanks to professional advice and consulting

▪ Cost savings and time gains

When we advise and support you right from the word "go", we can make sure that the right formwork systems are chosen and then used as planned. This lets you achieve optimum utilisation of the formwork equipment, and effective forming operations because your workflows will be correct.

▪ Maximised workplace safety

The advice and support we can give you in how to use the equipment correctly, and as planned, leads to greater safety on the job.

▪ Transparency Optimum resource utilisation with assistance from the Doka Formwork Experts

Seeing things through to a positive conclusion with professional support

Workflow optimisation, thanks to ▪ thorough utilisation planning ▪ internationally experienced project technicians ▪ appropriate transport logistics ▪ on-site support

Doka Services are a byword for transparency and efficiency here, offering ▪ jointly handled return of rented formwork ▪ professional dismantling ▪ efficient cleaning and reconditioning using special equipment

999746002 - 02/2014

Because our services and costs are completely transparent, there is no need for improvisation during the project – and no unpleasant surprises at the end of it.

▪ Reduced close-out costs

Our professional advice on the selection, quality and correct use of the equipment helps you avoid damage, and minimise wear-andtear.

9

User Information Column formwork KS Xlife

Product description The Column formwork KS Xlife is a top-quality, siteready column formwork system.

The formwork is easy to open and close, resulting in very short striking and set-up times. Another advantage is that there is no need for time-consuming assembly and dismantling work.

Just one crane cycle is all it takes to reposition the entire formwork unit, in one piece.

Product features: ▪ adjusting range between 20 cm and 60 cm, in 5 cm increments ▪ suitable for square and rectangular column crosssections ▪ no need to change the form-facing for different cross-sections ▪ no tie-holes and frame imprints in the concrete ▪ 30 cm height grid ▪ for column heights of up to 6.60 m ▪ easy to operate; simply fold/unfold the panels to set up and strip the formwork ▪ safe working environment ensured by using Platform planking KS or Doka column formwork platform 150/90cm ▪ safe vertical access provided by Ladder system XS ▪ easy and convenient to clean ▪ 21 mm form-facing screwed on from rear ▪ long service life thanks to its sturdy design and galvanised steel construction

9746-301-01

Permitted fresh-concrete pressure: 90 kN/m2

10

999746002 - 02/2014

User Information Column formwork KS Xlife

Areas of use Height grid

Column cross-sections

Panels with heights of 0.90 m, 1.20 m, 2.70 m and 3.30 m can be combined, resulting in a 30 cm height grid.

The column cross-sections can be either square or rectangular in shape, in a 5 cm grid from 20x20 cm to 60x60 cm â&#x20AC;&#x201C; with no need to modify the form-facing in any way.

Materials schedule Formwork height [m]

Xlife panel KS 3.30m

Xlife panel KS 2.70m

Xlife panel KS 1.20m

Xlife panel KS 0.90m

Locking hook KS

Super plate 15.0

Stacking screw KS

Protective plate KS*

Protective plate KS top*

Lifting ring

Prop head KS EB

Panel strut 340 IB

Panel strut 540 IB

20x20cm column

0.90 1.20 1.80 2.10 2.40 2.70 3.00 3.30 3.60 3.90 4.20 4.50 4.80 5.10 5.40 5.70 6.00 6.30 6.60

4 4 4 4 4 8

4 4 4 4 4 8 4 8 -

4 4 8 4 4 4 4 8 8 -

4 8 4 8 4 4 4 4 -

2 2 4 4 4 4 6 5 6 6 7 7 8 8 8 9 9 10 10

2 2 4 4 4 4 6 5 6 6 7 7 8 8 8 9 9 10 10

8 8 8 16 8 8 8 8 16 16 8 16 8 16 8

4 4 4 4 4 4 -

4 4 4 4 4 4 -

4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4

6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6

3 3 3 3 3 3 3 -

3 3 3 3 3 3 3 3 3

*A

Protective plate KS is included with the Xlife panels KS 2.70m and 3.30m and comes pre-mounted on the panels.

The Protective plate KS top is pre-mounted to the Xlife panels KS 2.70m and 3.30m, and protects the top edge of the Xlife sheet.

The Protective plates KS and KS top can also be ordered as separate parts where needed, and used on the Xlife 0.90m and 1.20m panels.

9746-303-01

60x60cm column

9746-304-01

20x60cm column (with formwork opened)

9746-305-01

999746002 - 02/2014

11

User Information Column formwork KS Xlife

Assembling the column formwork Preparing the panels ➤ Place each panel (A) on an approx. 20 cm high base support (B) (e.g. Doka formwork beams H20).

These supports must always be located under the ends of the panels. ➤ Tilt up the adjustment wing (C) and bolt it into place with U-bolts (D) .

➤ If not already mounted, fix a Protective plate KS to the bottom of the formwork unit and a Protective plate KS top to the top of the unit.

H

C

B

G 9746-335-01

G Protective plate KS top H Protective plate KS

A 9746-306-01

Be sure to store the Protective plates KS in a safe place so that they can be found again and fitted back on the panels after the stacking combination has been dismantled. ➤ Turn each panel over separately.

D 9746-306-02

➤ For vertical stacking configurations: Prepare further panels as described above.

Vertical stacking Dismounting/mounting the Protective plates KS: ▪ There is a Protective plate KS at the bottom of every finished formwork unit.

▪ At the top of every finished formwork unit, there is a 'Protective plate KS top'.

▪ No protective plates are needed between the Xlife panels. ➤ Dismount any previously mounted Protective plates KS and Protective plates KS top.

9746-308-01

➤ Join the panels with Stacking screws KS (E) (2 per panel), and secure these with linch pins (F) .

For an exact panel joint: use a formwork hammer as a centring tool.

F

E

9746-220-01

G H

9746-334-01

12

999746002 - 02/2014

User Information Column formwork KS Xlife

Finishing the formwork-half

Mounting the pouring platform

➤ Place additional unfolded panels onto the first panel(s), at right-angles.

Raising the formwork-half ➤ Raise the formwork-half by crane and push H20 formwork beams under the adjustment wing (H) .

This makes it easier to mount the Platform planking KS.

H 9746-309-01

H

Setting the column width: ➤ Use spacer bolts (G) to fix the desired column width 'a', and secure these bolts with linch pins.

9746-310-01

Mounting the Platform planking KS

a G

9746-309-02

➤ Insert the Platform planking KS (I) , using the hook (K) to hang it into place in the side-rail of the panel, and secure it with a nut and linch pin (L) . Then attach lifting rings (M) and secure them (see the section headed "Platform configurations with Platform planking KS").

Finishing the first formwork-half ➤ Continue from the section headed "Mounting the pouring platform".

Finishing the second formwork-half M

➤ Mount the 2 lifting rings (M) and fix them with nuts and linch pins.

K

L

M

M

I

9746-311-01

➤ Attach the formwork-half to the lifting rings and raise it by crane.

9746-313-01

Max. load-bearing capacity: 600 kg per Lifting ring 999746002 - 02/2014

13

User Information Column formwork KS Xlife

Mounting the railing ➤ Mount a Railing KS 1.00x0.85m (N) and secure it with a Spring cotter 5mm. ➤ Mount a Counter railing platform planking KS (O) and secure it with a Spring cotter 5mm.

Lifting the pre-assembled formworkhalves into the upright

☞

➤ Where panels have been vertically stacked, only ever lift completely assembled (i.e. Lshaped) formwork-halves. ➤ Attach a Doka 4-part chain 3.20m (P) to the lifting rings on the first formwork-half and raise this by crane.

O

N 9746-312-01

P

Mounting the ladder system ➤ Mount the Ladder system XS to the horizontally placed formwork-half (see the section headed "Ladder system XS with Platform planking KS").

9746-314-01

➤ Secure this formwork-half with 3 panel struts (see "Plumbing accessories" for details of how to attach the panel struts). Do not detach it from the crane until the panel struts are attached. ➤ Assemble the second formwork-half – beginning with the section headed "Preparing the panels".

9746-315-01

14

999746002 - 02/2014

User Information Column formwork KS Xlife

Joining the formwork-halves together

G

R

Q

S

9746-316-01

1) Use spacer bolts (G) to connect the 2nd formworkhalf to the 1st, for the required column width, and secure the bolts with linch pins. Only when this has been done is it allowed to detach the 2nd formworkhalf from the crane.

2) Fit in the Locking hook KS (R) as shown in the illustration.

3) Screw a Super plate 15.0 (S) onto the Locking hook KS. 4) Relocate the spacer bolt (Q) as shown in the illustration. The hole-grid with markings indicates the column width. When the spacer bolt is relocated on the closing side of the formwork, the column width must be increased by 5 cm. (Example: column width 40 cm = spacer bolt located at 45 cm).

5) Mount a triangular ledge (chamfer) (T) (with the formwork still unfolded).

Frontal triangular ledge KS 15 or 20mm

9746-237-01

â&#x2013;Ş

Framax triangular ledge 2.70m

9746-235-01

no nails needed

Alternatively: triangular ledge (chamfer) with max. 1 mm thick nailing strip.

T

Q 9746-316-02

999746002 - 02/2014

15

User Information Column formwork KS Xlife

Erecting and stripping the formwork Closing the formwork

➤ At the usage location, close the formwork around the reinforcing cage, or lower the closed formwork down over the reinforcing cage by crane. ➤ Plumb and align the column formwork with the panel struts (T) .

➤ Close the formwork.

T

T 9746-317-01

9746-318-01

➤ Hook the Locking hook KS (R) into the spacer bolt (Q) and tighten the formwork with the Super plate 15.0 (S) .

R

16

S

9746-319-01

Q

999746002 - 02/2014

User Information Column formwork KS Xlife

Striking

Cleaning and care of your equipment After pouring: ➤ Remove any blobs of concrete from the back-face of the formwork, using water (without any added sand).

Immediately after striking the formwork ➤ and before every pour, apply an extremely thin layer of concrete release agent to the form-ply and the end faces.

☞

Important note: Do not use any chemical cleaning agents!

9746-317-01

➤ Release the Locking hook KS (R) and open the formwork. ➤ Shift the Locking hook into the stand-by position.

R

9746-319-02

Insertion point for pry bar.

9746-320-01

999746002 - 02/2014

17

User Information Column formwork KS Xlife

Resetting Horizontal repositioning

Assembly instructions

With Shifting wheel KS

☞

The Shifting wheel KS makes it possible for Column formworks KS Xlife of up to 3.60 m in height to be horizontally travelled.

It can be clamped to 2.70 m and 3.30 m high panels.

4 Shifting wheels KS are needed for repositioning 1 Column formwork KS Xlife.

Leave enough space for the swivel castor ➤ by turning the Prop head KS 180° when mounting it to the Panel KS near the Shifting wheel KS.

9706-336-03

➤ Dismount the Connecting pin 10cm . ➤ Slot the top of the Shifting wheel KS unit into the cross-profile and frame tube, and pivot the whole unit into position.

9237-202-01

➤ Use the Connecting pin 10cm to fix the Shifting wheel KS in the bottom location fixture, and secure it with a spring cotter.

9237-203-01

Wheeling

9746-336-01

☞ ▪▪ ▪ ▪

9746-336-02

Max. load-bearing capacity: 300 kg per Shifting wheel KS 18

Do not attempt to wheel any Column formwork KS higher than 3.60 m.

Only wheel the column formwork when it is CLOSED – fix it in the closed position with a Locking hook KS. The floor must be stable, firm, not sloping, and sufficiently smooth (i.e. not gravel etc.)

When a column formwork is travelled that has platforms attached, there MUST be panel struts under the platform. Only unfix the panel struts from the ground – do not push them in!

➤ Using the spindles, raise the Column formwork KS Xlife around 2 cm off the ground. ➤ When wheeling the formwork, always have 2 people pushing (1 on either side).

999746002 - 02/2014

User Information Column formwork KS Xlife

Follow the directions in the "Shifting wheel KS" Operating Instructions!

➤ Reposition the formwork unit in one crane cycle.

Lifting by crane Fix the panels so that they cannot fold open and shut: ➤ Use a Connecting pin 10cm or spacer bolt on each Xlife panel KS to secure the unfolded panels against accidentally folding shut.

9746-323-01

Reposition the formwork: When an opened formwork unit is suspended from the crane, it must hang in the perpendicular! ➤ Adjust the Doka 4-part chain 3.20m to the centre-of-gravity position. ➤ Attach the crane to the lifting rings with the Doka 4part chain 3.20m.

Hoisting points on Platform planking KS 9746-322-01

B

A

B A

The platform can stay attached to the formwork throughout this entire operation.

Follow the directions in the "Doka 4-part chain 3.20m" Operating Instructions!

A

B

A

B

9746-325-03

To obtain as perpendicular a position as possible when the column formwork unit is suspended above the ground (either open or closed), use the following hoisting points: A-B-B-A (starting at the panel with the platform and continuing in a clockwise direction).

999746002 - 02/2014

19

User Information Column formwork KS Xlife

Changing the column cross-section The formwork can be quickly adjusted to a new column cross-section when it is standing in the upright: ▪ even if it has been vertically extended (stacked) upward or downward ▪ even with pouring platforms and ladderways attached

5) Attach the crane to the last two panels, at the positions shown, and slightly raise them.

6) Undo the spacer bolts between the panels, slide the panels to the desired position and fix them again with the spacer bolts.

6

Preparations ➤ Unfold the column formwork unit in the same way as when striking the formwork.

Fix the panels so that they cannot fold open and shut: ➤ Use a Connecting pin 10cm or spacer bolt on each Xlife panel KS to secure the unfolded panels against accidentally folding shut.

9746-337-01

5

9746-323-01

Adjustment procedure 1) On the panel with the double panel struts, fix these to the ground with Doka Express anchors 16x125mm.

2) At the positions shown, slightly lift the other 3 panels by crane.

3) Undo the spacer bolts between the panels, slide the panels to the desired position and fix them again with the spacer bolts.

4) Fix the panel strut of the freshly positioned panel to the ground, as shown in Point 1.

7) Attach the crane to the last panel, at the position shown, and slightly raise it.

8) Undo the spacer bolts between the panels, slide the panels to the desired position and fix them again with the spacer bolts.

8

9746-337-01

7 4

1

3

9746-337-01

2

9) Move the spacer bolts for the Locking hook (on the last panel) to their new position (column width + 5cm). See the section headed "Joining the formwork-halves together".

Note: The column cross-sections can also be adjusted with the panels in the horizontal. See "Finishing the formwork-half" in the section headed "Assembling the column formwork".

20

999746002 - 02/2014

User Information Column formwork KS Xlife

Plumbing accessories Panel struts

Fixing the struts to the formwork

Plumbing accessories brace the formwork against wind loads and make it easier to plumb and align.

➤ Bolt the Prop head KS into the waling profile and secure it with a linch pin. ➤ Bolt the panel strut onto the Prop head KS. (For details of how to locate the panel struts, see "Assembling the column formwork").

A

A

9746-234-01

B

B

9746-324-01

A Prop head KS EB B Panel strut 340 IB or 540 IB

Fixing to the ground 9746-253-01

➤ Anchor the Panel strut in such a way that it resists tensile and compressive forces!

A Panel strut 340 IB B Panel strut 540 IB

Holes in footplate of the Panel strut: Product features: ▪ Can be telescoped in 8 cm increments ▪ Fine adjustment by screw-thread ▪ All parts are captively integrated - including the telescopic tube (has safety stop to prevent dropout)

☞

Important note: The formwork panels must be held stable in every phase of the construction work!

Please observe all applicable safety regulations!

a

b

9727-343-01

a ... diam. 26 mm b ... diam. 18 mm

Anchoring the footplate The Doka Express anchor can be re-used many times over - the only tool needed for screwing it in is a hammer.

Items required for shoring each column formwork Formwork height Up to 3.90 m Up to 6.60 m

Panel strut 340 IB 3 -

Panel strut 540 IB 3

Prop head KS EB 6 6

The values apply where the wind pressure we = 0.65 kN/m2. This results in an impact pressure qp = 0.5 kN/m2 (102 km/h) where cp, net = 1.3. In cases where higher wind pressure is encountered, the number of props must be determined by statical calculation.

For more information, see the Calculation Guide "Wind loads to the Eurocodes" or ask your Doka technician!

A B TR632-201-01

A Doka Express anchor 16x125mm B Doka coil 16mm

Characteristic cube compressive strength of the concrete (fck,cube): min. 25 N/mm2 or 250 kg/cm2 (C20/25 grade concrete) Follow the Fitting Instructions!

Required safe working load of alternative anchors for foot-plates: Rd 20.3 kN (Fpermissible 13.5 kN) Follow the manufacturer's applicable fitting instructions.

999746002 - 02/2014

21

User Information Column formwork KS Xlife

Platform configurations with Platform planking KS Product description

Platform configuration without Ladder system XS

B

B D

B

B

B A A C

cm 90

85 cm 9746-257-01

A Platform planking KS B Railing KS 1.00x0.85m C Side railing KS 0.30m (incl. 2 tube linch pins)

☞

When the platform is used without a Ladder system XS, three Railings KS 1.00x0.85m (B) and one Side railing KS 0.30m (C) are needed.

9746-325-01

A Platform planking KS B Railing KS 1.00x0.85m D Counter railing platform planking KS

Permitted service load: 1.5 kN/m2 (150 kg/m2) Load Class 2 to EN 12811-1:2003 A safe working platform can quickly be erected using only a very few separate parts.

The main features: ▪ Platform is 0.90 m wide, permitting safe, convenient working.

▪ Level, unobstructed platform workspace, with no projecting parts.

▪ Is readied for operation in just a few simple steps.

▪ Does not take up much space in transit.

▪ Long service life thanks to its sturdy design and galvanised steel construction.

22

999746002 - 02/2014

User Information Column formwork KS Xlife

Ladder system XS with Platform planking KS Assembly instructions Preparing the formwork ➤ Pre-assemble the formwork units on their sides, on an assembly bench (see "Assembling the column formwork"). ➤ Mount the Platform planking KS to the formwork unit while it is lying on the assembly bench (see "Assembling the column formwork").

Attaching connectors to the formwork ➤ Attach a 'Connector XS for Platform planking KS' to the waling profile towards the bottom of the formwork: Swivel the 'Connector XS for Platform planking KS' (V) into place and secure it in the waling profile with a Connecting pin 10cm (O) and a spring cotter.

O

V

9746-327-03

9746-325-02

➤ Mount a 'Connector XS for Platform planking KS' near the top of the formwork, in the same way.

The Ladder system XS provides a safe and reliable way of climbing up and down column formworks: ▪ during pouring ▪ when placing reinforcing cages ▪ when opening/closing the formwork-halves ▪ when attaching/detaching the formwork-halves Note: The Ladder system XS must be implemented in such a way that all national regulations are complied with.

WARNING ➤ The Ladders XS may only be used as part of the XS system, and must NOT be used separately (as "lean-to" ladders).

999746002 - 02/2014

23

User Information Column formwork KS Xlife

Fixing the ladder

Ladder system XS for heights above 3.75 m

➤ Pull out the push-in bolt, and pivot the two safety hooks out of the way. ➤ Place the System ladder XS 4.40m onto the 'Connector XS for Platform planking KS', with the hooking brackets facing downwards. ➤ Close the safety hooks. ➤ Insert the push-in bolt into whichever rung of the ladder is suitable for the height of the formwork, and secure it with a linch pin.

Telescoping ladder extension (for adjusting to ground level) ➤ To telescope the ladders past one another, lift the safety latch on the ladder and fix the Ladder extension XS 2.30m onto the desired rung of the other ladder.

C

A

Note: Follow the special instruction for formwork heights of 2.70m (see the end of this section).

B

Top Connector XS for Platform planking KS Tr625-201-04

C

Close-up C

B

B A 9746-327-01

When planning to use the Securing barrier XS: The ladder must be bolted at least in the second ladder hole from the top to ensure it protrudes sufficiently to fix the Securing barrier XS.

Bottom Connector XS for Platform planking KS

Tr625-201-03

A System ladder XS 4.40m B Ladder extension XS 2.30m C Safety latch

A telescoping join between two Ladder extensions XS 2.30m can be made in the same way.

C B

A 9746-327-02

Permanently fixed ladder extension ➤ Insert the Ladder extension XS 2.30m into the uprights of the System ladder XS 4.40m, with its hooking brackets facing downwards, and fasten it.

Tighten the screws only very slightly!

A Push-in bolt B Safety hook C System ladder XS 4.40m

A

C

➤ Mount the Securing barrier XS to the ladder, with fixing hooks and wing-nuts.

D

B

Tr625-202-01

Screws (C) are included in the scope of supply of the System ladder XS 4.40m and the Ladder extension XS 2.30m.

9746-267-01

D Securing barrier XS (pivoting)

The components needed for mounting the Securing barrier XS are captively attached to it.

24

A System ladder XS 4.40m B Ladder extension XS 2.30m C Screws, width-across 17 mm

Two Ladder extensions XS 2.30m can be fixed together in the same way.

999746002 - 02/2014

User Information Column formwork KS Xlife

Ladder cage

☞

Important note: ➤ Always observe all relevant safety regulations applying to the use of the Ladder cage XS in the country in which you are operating (e.g. in Germany: BGV D 36). ➤ Fix the Ladder cage exit XS (E) (the underside must always be at the same height as the 'Connector XS for Platform planking KS' (D) ). The safety latches (J) prevent the cage being accidentally lifted out.

Special instruction for formwork heights of 2.70m The ladder is normally always mounted with the hooking brackets at the bottom.

Exception: On 2.70m high formworks, the ladder must be turned upside down and mounted with the hooking brackets at the top, as otherwise it cannot be bolted to the Connectors XS.

E

B D

J

9746-326-01

➤ Fix the Ladder cage XS 1.00m (F) onto the next available rung. The safety latches (J) prevent the cage being accidentally lifted out. Add further Ladder cages XS 1.00m, in each case fixing them onto the next available rung.

9746-338-01

Items needed

F

J Tr625-201-02

Platform + ladder Connector XS for Platform planking KS System ladder XS 4.40m Ladder extension XS 2.30m

Ladder cage Ladder cage exit XS Securing barrier XS Ladder cage XS 1.00m

999746002 - 02/2014

Formwork-half with platform 2.70 m>3.60 m- >5.70 m3.60 m 5.70 m 6.60 m 2

2

2

1 —

1 1

1 2

Formwork-half with platform 2.70 m- >3.25 m- >4.30 m- >5.50 m3.25 m 4.30 m 5.50 m 6.60 m 1 1 1 1 1 1 1 1 — 1 2 3

25

User Information Column formwork KS Xlife

Platform configurations with Doka column formwork platform 150/90cm Product description

Basic design concept ➤ Tip up the side railings.

A

C

B

D

150 cm

A B C D

9719-203-01

E

cm 90

The railings are locked in place automatically. ➤ Tip up the rear railings.

Rear railing Side railing Rear hoisting point Safety hook (blue) = front hoisting point

E Extra hoisting point (red) in parked position

Permitted service load: 1.5 kN/m2 (150 kg/m2) Load Class 2 to EN 12811-1:2003 The main features: ▪ This pre-assembled, ready-to-use platform ensures convenient and safe working on column formworks.

It can be used on columns of any cross-section.

▪ The slinging points recessed into the decking make it a quick and easy job to lift the platform by crane.

Only one column formwork platform can be used on each column!

▪ Because the platform can be re-suspended so quickly, it can "migrate" from one formwork to the next during concreting. This means that one platform is sufficient to serve several column formworks.

▪ The practical swing-out side railings make it easy to get on or off the platform. Both the side railings can be fixed in either the open or closed position.

Combined with the Column formwork platform 150/90cm, the Doka Ladder system XS provides a safe and reliable way of climbing up and down column formworks.

26

The railings are locked in place automatically.

The column-formwork platform is now ready for use.

Note: When folding the platform back down, first fold down the rear railings, and then the side ones. ➤ Mount the 'Counter railing Col. formwork plat.

150/90cm' and secure with Spring cotters 5mm.

9746-339-02

999746002 - 02/2014

User Information Column formwork KS Xlife

Preparing the formwork ➤ Fit 2 Platform adapters KS (K) onto the pre-assembled formwork-half and secure them with nuts and linch pins (L) .

➤ After the column formwork platform has been hung into place on the formwork, detach the four-part lifting chain.

D

K K

9746-222-01

L

The safety hook (D) drops down into its starting position and automatically secures the platform against being accidentally lifted out. ➤ When the platform is lifted, the lifting chain acts on the safety hook (D) and the platform is automatically unlocked.

9746-328-01

Moving the platform D

➤ Attach the crane to the locations shown.

C C 9746-236-01

D C

Follow the directions in the "Doka 4-part chain 3.20m" Operating Instructions!

D

D

9744-207-01

C Rear crane suspension point D Front crane suspension point

➤ Hook the platform onto the pre-mounted Platform adapter KS.

9746-223-01

Suspending the platform exactly in position is made much easier when guide-cables are used.

999746002 - 02/2014

27

User Information Column formwork KS Xlife

Moving the formwork and the platform in one piece To save crane time, the Doka column formwork platform can also be repositioned together with the formwork: ➤ Hang the platform into place on the formwork (proceed as in "Moving the platform"). ➤ Move the extra crane hoisting point (E) from the parked position to the "in-use" position. Right position = inclined forward towards formwork.

Reposition the formwork: When an opened formwork unit is suspended from the crane, it must hang in the perpendicular! ➤ Adjust the Doka 4-part chain 3.20m to the centre-of-gravity position (shorten chainlengths by 6 chain-links). ➤ Attach the crane to the lifting rings with the Doka 4part chain 3.20m.

Hoisting points on Doka column formwork platform 150/90 4

E

3

2

1 4 3

X

2 1

X

9746-330-01

➤ Fix the extra crane hoisting point with the slide bolt (F) on the underside of the platform.

9746-331-02

To ensure as perpendicular a position as possible when the formwork unit is suspended above the ground (either open or closed), use hoisting points X-1-1-X.

F

9746-213-01

Make sure that the slide bolt latches in in the frontmost position.

Fix the panels so that they cannot fold open and shut: ➤ Use a Connecting pin 10cm or spacer bolt on each Xlife panel KS to secure the unfolded panels against accidentally folding shut.

9746-323-01

28

999746002 - 02/2014

User Information Column formwork KS Xlife

➤ Reposition the formwork unit in one crane cycle.

9746-329-01

The platform can stay attached to the formwork throughout this entire operation.

Follow the directions in the "Doka 4-part chain 3.20m" Operating Instructions!

Separating the platform from the formwork ➤ Fix the slide bolt (F) back in the rear position and move the extra crane hoisting point into the "parked" position. ➤ Attach the crane to the locations shown in "Moving the platform".

999746002 - 02/2014

29

User Information Column formwork KS Xlife

30

999746002 - 02/2014

User Information Column formwork KS Xlife

Ladder system XS on Doka column formwork platform 150/90cm Pre-assembly â&#x17E;¤ Pre-assemble the Ladder system XS and the Column formwork platform 150/90cm flat on the ground, and hoist them onto the upright half of the formwork using the Doka 4-part chain 3.20m. (Shorten the 2 lengths of chain nearest the entry-point by removing approx. five chain-links!)

G

Tr625-201-01

A

E

G1

F D

F

B

F

C

C

A B C D E F G

Doka column formwork platform 150/90cm System ladder XS 4.40m Ladder extension XS 2.30m Connector XS column formwork platform Ladder cage exit XS Ladder cage XS 1.00m Doka 4-part chain 3.20m G1 shortened lengths of chain

9746-331-01

999746002 - 02/2014

31

User Information Column formwork KS Xlife

➤ Fasten the 'Connector XS for column formwork platform' (D) to the Doka column formwork platform 150/90cm (A) , using the screws, bolts etc. supplied.

(Only Column formwork platforms manufactured since 02/2002 come with pre-drilled holes for attaching the Connector XS. Older Column formwork platforms will be retrofitted with these holes.) ➤ Place the System ladder XS 4.40m (B) onto the Connector XS, with the hooking brackets facing downwards. ➤ Insert the push-in bolt (H) into the rung that is suitable for the height of the column, and twist to secure.

Telescoping ladder extension (for adjusting to ground level) ➤ To telescope the ladders past one another, lift the safety latch (I) on the ladder (B) and fix the Ladder extension XS 2.30m (C) onto the desired rung of the other ladder.

B

I

Tr625-203-01

D C

c

A

Tr625-201-04

B H

Close-up

b I

a

C

d

a ... Hole for a column height of 2.70 m b ... Hole for a column height of 3.00 m c ... Hole for a column height > 3.30 m d ... Extra hole for special applications

Permanently fixed ladder extension ➤ Insert the Ladder extension XS 2.30m (C) into the uprights of the System ladder XS 4.40m (B) , with its hooking brackets facing downwards, and fasten it with the screws, bolts etc. supplied (width-across 17mm).

B C

Tr625-201-03

A telescoping join between two Ladder extensions XS 2.30m can be made in the same way.

Ladder cage

☞

Important note: ➤ Always observe all relevant safety regulations applying to the use of the Ladder cage XS in the country in which you are operating (e.g. in Germany: BGV D 36). ➤ Fix the Ladder cage exit XS (E) (the underside must always be at the same height as the 'Connector XS for column formwork platform' (D) ). The safety latches (J) prevent the cage being accidentally lifted out.

E

Tr625-202-01

Two Ladder extensions XS 2.30m can be fixed together in the same way.

B D

J Tr625-211-01

32

999746002 - 02/2014

User Information Column formwork KS Xlife

➤ Fix the Ladder cage XS 1.00m (F) onto the next available rung. The safety latches (J) prevent the cage being accidentally lifted out. Add further Ladder cages XS 1.00m, in each case fixing them onto the next available rung.

➤ Fit in the U-angle (N) under the waling profile, swivel the Connector XS KS (V) into place and secure it in the waling profile with a Connecting pin 10cm and a spring cotter (O) .

O

9746-332-01

N

V F

J Tr625-201-02

Assembly instructions ➤ Hang the prepared column formwork platform, complete with the ladder, into place on the column formwork.

➤ Pull out the push-in bolt (H) , pivot the two safety hooks (M) out of the way, and insert the ladder. ➤ Snap-close the safety hooks (M) , insert the push-in bolt (H) again and twist it to secure it: - in the frontmost position (a) for one single ladder - in the rear position (b) in the telescoping zone (for 2 ladders)

b H

9746-332-02

M M

a

Items needed Formwork-half with Column formwork platform 150/90cm 2.70 m>3.60 m- >5.70 m3.60 m 5.70 m 6.60 m

Platform + ladder Connector XS for column formwork platform Connector XS KS System ladder XS 4.40m Ladder extension XS 2.30m

1

1

1

1 1 —

1 1 1

1 1 2

9746-331-01

Ladder cage Ladder cage exit XS Securing barrier XS Ladder cage XS 1.00m

999746002 - 02/2014

Formwork-half with Column formwork platform 150/90cm 2.70 m- >3.15 m- >4.20 m- >5.40 m3.15 m 4.20 m 5.40 m 6.60 m 1 1 1 1 1 1 1 1 — 1 2 3

33

User Information Column formwork KS Xlife

34

999746002 - 02/2014

User Information Column formwork KS Xlife

Transporting, stacking and storing When folded closed, the Column formwork KS Xlife panels are easy to transport and store.

9746-302-01

Example: Stacking dimensions for 4 Xlife panels KS 2.70m Length = 276.0 cm, width = 90.0 cm, height incl. 10 cm squared timbers = 66.4 cm

â&#x2DC;&#x17E;

Important note: When stacking the panels, make sure that the adjustment wing (A) is always resting on the cross profile (B) beneath it.

A B

999746002 - 02/2014

35

User Information Column formwork KS Xlife

Utilise the benefits of Doka multi-trip packaging on your site.

Multi-trip packaging such as containers, stacking pallets and skeleton transport boxes keep everything in place on the site, minimise time wasted searching for parts, and streamline the storage and transport of system components, small items and accessories.

Doka skeleton transport box 1.70x0.80m

Using Doka skeleton transport boxes 1.70x0.80m as transport devices Lifting by crane ➤ Only lift the boxes when their sidewalls are closed!

☞ ▪▪ ▪

Multi-trip packaging items may only be lifted one at a time.

Use a suitable lifting chain (e.g. Doka 4-part chain 3.20m).

Do not exceed the permitted load-bearing capacity.

Spread-angle  max. 30°!

9234-203-01

Repositioning by forklift truck or pallet stacking truck Storage and transport devices for small items: ▪ durable ▪ stackable

The forks can be inserted under either the broadside or the narrowside of the containers.

Suitable transport appliances: ▪ crane ▪ pallet stacking truck ▪ forklift truck To make the "Doka skeleton transport box" easier to load and unload, one of its sidewalls can be opened.

Max. load: 700 kg Permitted imposed load: 3150 kg

☞▪ ▪

Multi-trip packaging items that each contain very different loads must be stacked with the heaviest ones at the bottom and the lightest ones at the top!

Rating plate must be in place and clearly legible

Using Doka skeleton transport boxes 1.70x0.80m as storage units Max. n° of boxes on top of one another Outdoors (on the site) Floor gradient up to 3% 2 It is not allowed to stack empty pallets on top of one another!

36

Indoors Floor gradient up to 1% 5

999746002 - 02/2014

User Information Column formwork KS Xlife

Doka multi-trip transport box 1.20x0.80m galv.

Possible ways of dividing the box Multi-trip transport box partition 1.20m 0.80m

Lengthways

Crossways

max. 3 partitions -

max. 3 partitions

Tr755-200-04

Tr755-200-05

Using Doka multi-trip transport boxes as storage units Max. n° of boxes on top of one another Outdoors (on the site) Floor gradient up to 3% 3 It is not allowed to stack empty pallets on top of one another!

Storage and transport devices for small items: ▪ durable ▪ stackable Suitable transport appliances: ▪ crane ▪ pallet stacking truck ▪ forklift truck

Using Doka multi-trip transport boxes as transport devices

Max. load: 1500 kg Permitted imposed load: 7900 kg

☞▪ ▪

Indoors Floor gradient up to 1% 6

Lifting by crane

Multi-trip packaging items that each contain very different loads must be stacked with the heaviest ones at the bottom and the lightest ones at the top!

Rating plate must be in place and clearly legible

☞ ▪▪ ▪

Multi-trip packaging items may only be lifted one at a time.

Use a suitable lifting chain (e.g. Doka 4-part chain 3.20m).

Do not exceed the permitted load-bearing capacity.

Spread-angle  max. 30°!

Multi-trip transport box partition Different items in the Multi-trip transport box can be kept separate with the Multi-trip transport box partitions 1.20m or 0.80m.

Tr755-200-02

A

9206-202-01

Repositioning by forklift truck or pallet stacking truck A Slide-bolt for fixing the partition

999746002 - 02/2014

The forks can be inserted under either the broadside or the narrowside of the containers.

37

User Information Column formwork KS Xlife

Doka stacking pallet 1.55x0.85m and 1.20x0.80m Storage and transport devices for long items: ▪ durable ▪ stackable Suitable transport appliances: ▪ crane ▪ pallet stacking truck ▪ forklift truck The Bolt-on caster set B turns the stacking pallet into a fast and manoeuvrable transport trolley.

Follow the directions in the "Bolt-on castor set B" Operating Instructions!

Using Doka stacking pallets as transport devices Lifting by crane

☞ ▪▪ ▪ ▪ ▪

▪

Multi-trip packaging items may only be lifted one at a time.

Use a suitable lifting chain (e.g. Doka 4-part chain 3.20m).

Do not exceed the permitted load-bearing capacity.

Load the items centrically.

Fasten the load to the stacking pallet so that it cannot slide or tip out.

When lifting stacking pallets to which Bolt-on castor sets B have been attached, you must also follow the directions in these Operating Instructions!

Spread-angle  max. 30°!

=

Max. load: 1100 kg Permitted imposed load: 5900 kg

☞▪ ▪

Multi-trip packaging items that each contain very different loads must be stacked with the heaviest ones at the bottom and the lightest ones at the top!

Rating plate must be in place and clearly legible

Using Doka stacking pallets as storage units

a

=

92815-224-01

Doka stacking pallet 1.55x0.85m Doka stacking pallet 1.20x0.80m

a max. 4.0 m max. 3.0 m

Repositioning by forklift truck or pallet stacking truck

☞ ▪▪

Load the items centrically.

Fasten the load to the stacking pallet so that it cannot slide or tip out.

Max. n° of units on top of one another Outdoors (on the site) Floor gradient up to 3% 2 It is not allowed to stack empty pallets on top of one another!

☞▪

38

Indoors Floor gradient up to 1% 6

How to use with bolt-on castor set: Always apply the fixing brake when the container is "parked".

When Doka stacking pallets are stacked, the bottom pallet must NOT be one with a bolt-on caster set mounted to it.

999746002 - 02/2014

User Information Column formwork KS Xlife

Doka accessory box

Doka accessory box as transport devices

Storage and transport devices for small items: ▪ durable ▪ stackable

Lifting by crane

Suitable transport appliances: ▪ crane ▪ pallet stacking truck ▪ forklift truck The Doka accessory box is the tidy, easy-to-find way of storing and stacking all interconnection and form-tie components.

The Bolt-on caster set B turns the stacking pallet into a fast and manoeuvrable transport trolley.

☞ ▪▪ ▪

▪

Multi-trip packaging items may only be lifted one at a time.

Use a suitable lifting chain (e.g. Doka 4-part chain 3.20m).

Do not exceed the permitted load-bearing capacity.

When lifting stacking pallets to which Bolt-on castor sets B have been attached, you must also follow the directions in these Operating Instructions!

Spread-angle  max. 30°!

Follow the directions in the "Bolt-on castor set B" Operating Instructions!

92816-206-01

Repositioning by forklift truck or pallet stacking truck The forks can be inserted under either the broadside or the narrowside of the containers.

Max. load: 1000 kg Permitted imposed load: 5530 kg

☞

▪ Multi-trip packaging items that each contain

▪

very different loads must be stacked with the heaviest ones at the bottom and the lightest ones at the top!

Rating plate must be in place and clearly legible

Bolt-on castor set B The Bolt-on caster set B turns the stacking pallet into a fast and manoeuvrable transport trolley.

Suitable for drive-through access openings > 90 cm.

Doka accessory box as storage units Max. n° of boxes on top of one another Outdoors (on the site) Floor gradient up to 3% 3 It is not allowed to stack empty pallets on top of one another!

☞

Indoors Floor gradient up to 1% 6

▪ How to use with bolt-on castor set:

The Bolt-on caster set B can be mounted to the following multi-trip packaging items: ▪ Doka accessory box ▪ Doka stacking pallets Follow the directions in the Operating Instructions!

Always apply the fixing brake when the container is "parked".

When Doka accessory boxes are stacked, the bottom box must NOT be one with a bolton castor set mounted to it.

999746002 - 02/2014

39

Component overview

User Information Column formwork KS Xlife [kg]

Article n째

[kg]

Article n째

Component Article [kg] n째 overview

Xlife panel KS 3.30m

185.0 580346500

Xlife-Element KS 3,30m

Locking hook KS

0.83 580344000

Verschlusshaken KS

Galvanised Length: 31 cm

Galvanised Width: 80 cm Delivery condition: folded closed

Super plate 15.0

1.1 581966000

Superplatte 15,0

Galvanised Height: 6 cm Diameter: 12 cm Width-across: 27 mm

Lifting ring

1.4 580340000

Umsetzring

Galvanised Height: 20 cm

Xlife panel KS 2.70m

140.0 580337500

Xlife-Element KS 2,70m

Galvanised Width: 80 cm Delivery condition: folded closed

Stacking screw KS

0.77 580345000

Aufstockschraube KS

Galvanised Height: 20 cm

Frontal triangular ledge KS 20 4.00m Frontal triangular ledge KS 15 4.00m Stirndreikantleiste KS

0.93 580347000 0.71 580359000

Grey

Xlife panel KS 1.20m

66.0 580338500

Xlife-Element KS 1,20m

Galvanised Width: 80 cm Delivery condition: folded closed

Xlife panel KS 0.90m

56.0 580339500

Xlife-Element KS 0,90m

Galvanised Width: 80 cm Delivery condition: folded closed

Framax triangular ledge 2.70m

0.38 588170000

Panel strut 340 IB

24.3 580365000

(A) Plumbing strut 340 IB

16.7 588696000

Framax-Dreikantleiste 2,70m

Elementst체tze 340 IB consisting of:

Galvanised Length: 190.8 - 341.8 cm

(B) Adjusting strut 120 IB

7.6 588248500

Galvanised Length: 81.5 - 130.6 cm Galvanised Delivery condition: folded closed

Protective plate KS

3.3 580343000

Schutzleiste KS

Galvanised Length: 70 cm Width: 9 cm

A

B

Protective plate KS top

3.0 580357000

Schutzleiste KS oben

Galvanised Length: 65.3 cm Width: 8.4 cm

40

999746002 - 02/2014

User Information Column formwork KS Xlife

Component overview [kg]

Article n°

Panel strut 540 IB

41.4 580366000

(A) Plumbing strut 540 IB

30.7 588697000

Elementstütze 540 IB consisting of:

Galvanised Length: 310.5 - 549.2 cm

(B) Adjusting strut 220 IB

[kg] Counter railing col. formwork plat. 150/90cm Gegengeländer Stützenbühne 150/90cm Galvanised Width: 87 cm Height: 170 cm

Article n°

8.0 588385000

10.9 588251500

Galvanised Length: 172.5 - 221.1 cm Galvanised Delivery condition: folded closed

Platform planking KS

32.3 580360000

Fertigbelag KS

Timber parts varnished yellow Steel parts galvanised Length: 90 cm Width: 85 cm

A

B

Railing KS 1.00x0.85m

12.4 580363000

Fertiggeländer KS 1,00x0,85m Galvanised

Prop head KS EB

0.85 580342000

Stützenkopf KS EB

Galvanised Length: 14 cm Width: 11 cm Height: 14 cm

Universal dismantling tool

3.7 582768000

Universal-Lösewerkzeug

Galvanised Length: 75.5 cm

Counter railing platform planking KS Gegengeländer Fertigbelag KS

7.4 580361000

Galvanised Width: 91.6 cm Height: 170 cm

Doka express anchor 16x125mm Doka-Expressanker 16x125mm

0.31 588631000

Galvanised Length: 18 cm Follow fitting instructions!

Side railing KS 0.30m

2.6 580364000

Seitengeländer KS 0,30m

Doka coil 16mm

Galvanised Length: 38 cm Width: 30 cm Height: 53 cm

0.009 588633000

Doka-Coil 16mm

Galvanised Diameter: 1.6 cm

Shifting wheel KS Platform adapter KS

11.4 580341000

Bühnenanschluss KS

Galvanised Length: 74 cm Width: 12 cm Height: 20 cm

Doka column formwork platform 150/90cm Doka-Stützenbühne 150/90cm

Umsetzrad KS

15.8 580358000 Galvanised Follow the directions in the "Operating Instructions"!

211.8 588382000

Galvanised Length: 173 cm Width: 173 cm Height: 130 cm Delivery condition: folded closed

999746002 - 02/2014

41

Component overview

User Information Column formwork KS Xlife [kg]

Doka 4-part chain 3.20m

Article n°

15.0 588620000

Doka-Vierstrangkette 3,20m

[kg] Ladder extension XS 2.30m

19.1 588641000

Leiternverlängerung XS 2,30m

Galvanised

Follow the directions in the "Operating Instructions"!

Connecting pin 10cm

Article n°

0.34 580201000

Verbindungsbolzen 10cm

Galvanised Length: 14 cm

Securing barrier XS

4.9 588669000

Sicherungsschranke XS Galvanised Length: 80 cm

Ladder system XS Connector XS KS

13.2 580367000

Anschluss XS KS

Galvanised Length: 115 cm

Connector XS column formwork platform Anschluss XS Stützenbühne

Ladder cage XS 1.00m Ladder cage XS 0.25m

16.5 588643000 10.5 588670000

Rückenschutz XS

Galvanised

10.0 588637000

Galvanised Length: 123 cm

Ladder cage exit XS

17.0 588666000

Rückenschutz-Ausstieg XS Galvanised Height: 132 cm

Connector XS platform decking KS Anschluss XS Fertigbelag KS

11.0 580368000

Galvanised Length: 161.8 cm

System ladder XS 4.40m

33.2 588640000

System-Leiter XS 4,40m

Galvanised

42

999746002 - 02/2014

User Information Column formwork KS Xlife

Component overview [kg]

Article n°

Multi-trip packaging

[kg] Bolt-on castor set B

33.6 586168000

Anklemm-Radsatz B

Doka skeleton transport box 1.70x0.80m

87.0 583012000

Doka-Gitterbox 1,70x0,80m

Article n°

Painted blue

Galvanised Height: 113 cm

Doka multi-trip transport box 1.20x0.80m

75.0 583011000

Doka-Mehrwegcontainer 1,20x0,80m Galvanised Height: 78 cm

Multi-trip transport box partition 0.80m Multi-trip transport box partition 1.20m

3.7 583018000 5.5 583017000

Mehrwegcontainer Unterteilung

Timber parts varnished yellow Steel parts galvanised

Doka stacking pallet 1.55x0.85m

42.0 586151000

Doka-Stapelpalette 1,55x0,85m

Galvanised Height: 77 cm

Doka stacking pallet 1.20x0.80m

39.5 583016000

Doka-Stapelpalette 1,20x0,80m

Galvanised Height: 77 cm

Doka accessory box

106.4 583010000

Doka-Kleinteilebox

Timber parts varnished yellow Steel parts galvanised Length: 154 cm Width: 83 cm Height: 77 cm

999746002 - 02/2014

43

Near to you, worldwide Doka is one of the world leaders in developing, manufacturing and distributing formwork technology for use in all fields of the construction sector.

With more than 160 sales and logistics facilities in over 70 countries, the Doka Group has a highly efficient distribution network which ensures that equipment and

technical support are provided swiftly and professionally.

An enterprise forming part of the Umdasch Group, the Doka Group employs a worldwide workforce of more than 5600.

Doka GmbH | Josef Umdasch Platz 1 | 3300 Amstetten | Austria | T +43 7472 605-0 | F +43 7472 66430 | oesterreich@doka.com | www.doka.com

999746002 - 02/2014