Acon air 16 sport trampoline

Rectangular Trampoline System User’s Manual

Size: 10ft x 17ft x 138 Springs

9

Assembly, Installation, Care, Maintenance, and Use Instructions

WARNING Read these materials prior to assembling and using this trampoline

Use trampoline only with mature, knowledgeable supervision This trampoline is not recommended for use by children under six years of age.

D O N OT a t t e m p t o r a l l o w somersaults. Landing on the head or neck can cause serious injury, paralysis or death, even when landing in the middle of the bed.

DO NOT attempt to jump over the barrier.

DO NOT allow more than one person on the trampoline. DO NOT allow more than one person inside the trampoline enclosure. Use by more than one person at the same time can result in serious injury.

DO NOT intentionally rebound off the barrier.

DO NOT hang from, kick, cut or climb on the barrier.

Assembly and Installation Instructions Preparation Before you begin assembling your Rectangular Trampoline System, make sure your trampoline is in a proper location.

Trampoline Placement Caution: When deciding on where to place your trampoline, consider the following:

WARNING Overhead Clearance

Adequate overhead clearance is essential. A minimum of 24 feet from ground level is recommended. Provide clearance for wires, tree limbs, and other possible hazards.

Lateral Clearance

Lateral clearance is essential. Place the trampoline and trampoline enclosure away from walls, structures, fences, and other play areas. Maintain a clear space on all sides of the trampoline and trampoline enclosure.

Level Surface

Place the trampoline and trampoline enclosure on a level surface before use.

Lighting

Use the trampoline and trampoline enclosure in a well-lighted area. Artificial illumination may be required for indoor or shady areas.

Security ..............

Secure the trampoline and trampoline enclosure against unauthorized and unsupervised use.

Ground Clearance

Remove any obstructions from beneath the trampoline and trampoline enclosure.

Note: The trampoline enclosure is only to be used as an enclosure for a trampoline and the trampoline must be of the appropriate size as covered by the specific enclosure.

Note: The owner and supervisors of the trampoline are responsible to make all users aware of practices specified in the Use Instructions.

It is the responsibility of the purchaser to become familiar with all of the information in this booklet, to convey the warnings to all users.

This unit is not intended for commercial or public use and is therefore strictly prohibited.

This trampoline is not recommended for use by children under six years of age.

1

Assembly and Installation Instructions The following pages contain diagrams, pictures, and written instructions for assembling your Rectangular Trampoline System.

Familiarize yourself with the Assembly and Installation Instructions before beginning installation.

For installation questions, please contact us.

Parts List ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 H1 H2 H3 H4 H5 H6

DESCRIPTION L Shape Leg for Middle Bar Connect Bar for Middle Leg Support Steel Plate Leg Extension for Middle Leg Side Bar L Shape Corner Bar A L Shape Corner Bar B End bar Leg Extension for End Leg Connect Bar for End Leg Jumping Mat Springs Short Pad for End Bar Long Pad for Side Bar Bungee Cord M8x80 Socket Button Head Screw 8mm Washer M8 Nylon Lock Nut M8 Plastic Acorn Nut M8x85 Socket Button Head Screw M8x60 Socket Button Head Screw

2

Q'TY 4 2 2 4 2 2 2 2 4 2 1 138 2 2 18 20 64 32 32 8 4

Assembly and Installation Instructions

Assembly

Note: We recommend at least 2 people participate in assembling the trampoline.

1. Attach the “L” Shape Leg for Middle Leg (1) to Connect Bar for Middle Leg (2), and connect them by M8x80mm Socket Button Head Screw (H1). This step use following parts: Item 1 2 H1 H2 H3 H4

Description “L” Shape Leg for Middle Leg Connect Bar for Middle Leg M8x80 Socket Button Head Screw 8mm Washer M8 Nylon Lock Nut M8 Plastic Acorn Nut

Q’ty 4 2 4 8 4 4

Please do not tighten all of the screws.

1

Finished View H4 H3 H2

2

H2 H1 1

Note: This rectangular trampoline use 3 kinds of screws assembly: M8x60 Screw Assembly M8x80 Screw Assembly M8x85 Screw Assembly Please refer Screw List.

Each Screw assembly included a M8 screw, 2 pcs 8mm washers, a M8 Nylon Lock nut and a M8 Plastic Acorn Nut. Please refer Screw assembled.

Screw List

Screw Assembled H6 M8x60 Socket Button Head Screw

H1,H5&H6 H2

H1 M8x80 Socket Button Head Screw

H2 H3

H5 M8x85 Socket Button Head Screw

3

H4

Assembly and Installation Instructions 2. Attach the Leg Extension for Middle Leg (4) to “L” Shape Leg for Middle Leg (1), and connect them by M8x80mm Socket Button Head Screw (H1).

3. Attach Connect Support Steel Plate (3) to “L” Shape Leg for Middle Leg (1), and connect these3 parts by M8x85 Socket Button Head Screw assembly (H5, H2,H3 &H4) * Item Description Q’ty 3 Support Steel Plate 2 4 Leg Extension for Middle Leg 4 H1 M8x80 Socket Button Head Screw 4 H2 8mm Washer 24 H3 M8 Nylon Lock Nut 12 H4 M8 Plastic Acorn Nut 12 H5 M8x85 Socket Button Head Screw 8 Please do not tighten the screws.

Repeat step 1, 2 and 3 for another middle leg.

4

H2 1 3

H4 H1

H3 H5 4. Attach End Bar (8) to the Corner Bar A & B (6&7) , and tighten it by M8x80 Socket Button Head Screw Assembly (including H1, H2, H3&H4). * End bar has 17 spring holes.

5. Attach Middle Leg Assembly to the Socket at the Corner Bar, and tighten it by M8x80 Socket Button Head Screw Assembly (including H1, H2, H3&H4).

Item 6 7 8 H1 H2 H3 H4

Description L Shape Corner Bar A L Shape Corner Bar B End Bar M8x80 Socket Button Head Screw 8mm Washer M8 Nylon Lock Nut M8 Plastic Acorn Nut

Q’ty 2 2 2 8 16 8 8

H1 H2

6

7

8 Note: The “L’ Shape Corner Bars have 2 mirror directions, one in right hand and one in left. Please see assemble picture on the top.

6 H2 H3 H4

H1

4

Assembly and Installation Instructions

7

8 5

6

5

6. Attach 2 Side Bars (5) to the Corner Bar (6&7), and tighten by M8x80 Socket Button Head Screw Assembly (including H1, H2, H3&H4). * Side bar has 18 spring holes.

Item 5 H1 H2 H3 H4

Description Side Bar M8x80 Socket Button Head Screw 8mm Washer M8 Nylon Lock Nut M8 Plastic Acorn Nut

Q’ty 2 4 8 4 4

7. Repeat step 6 for another side. Please refer the picture as shown.

Finished View

5

Assembly and Installation Instructions

7

9

H4

H2

9

H3 10 H2 6 H6 9

10

8. Insert Leg Extension for End Leg (9) swage side into the both end of the Connect Bar for End Leg (10), and tighten by M8x60 Socket Button Head Screw (H6) Assembly (H6, H2, H3&H4) 9. Attach Side Leg Assembly to the welded Socket on the “L” Shape Corner Bar (6, 7).

Item 9 10 H6 H2 H3 H4

Description Leg Extension for End Leg Connect Bar for End Leg M8x60 Socket Button Head Screw 8mm Washer M8 Nylon Lock Nut M8 Plastic Acorn Nut

Q’ty 4 2 4 8 4 4

Note: Please fully tighten all bolts this time.

6

Finished View

Assembly and Installation Instructions 10. Connect Jumping Mat (11) to trampoline frame by attach a spring to the two V-rings closest to each corner. Warning label on mat must face up.

11 Mat

Note: For easy spring installation, use a Special spring tool to hook onto the one you are installing.

ďź&#x;

Person 2

Note: It is important to have someone work across from you.

Otherwise the springs could become over-extended, causing them to become difficult to connect.

11 Mat

CAUTION Pinch point.

Pay careful attention to hand position when connecting tubes and handling springs.

Finished View Person 1 Item 11 12

7

Description Jumping Mat Springs

Q’ty 1 138

Assembly and Installation Instructions

13 14

To “D�-Ring

15

12. Install pad bungee Cord onto bottom side of pad, as shown.

Note: Do not use pad Bungee Cord to secure frame pad around leg of trampoline at this time. This will be done after installing the safety enclosure poles in a later step.

11. Line up pads so they completely cover all springs and rail pieces, on all sides of the trampoline. Connect each pad section together using Velcro pieces at each end of pad. Velcro on each long pad piece will connect to bottom of each short pad piece.

Item 13 14 15

Description Short Pad for End Bar Long Pad for Side Bar Bungee Cord

Q’ty 2 2 18

WARNING: Trampoline use is not recommended without the frame pad installed. The frame pad is designed to reduce the possibility of injury by protecting the user from coming into contact with the frame and springs of the trampoline. It is very important that you properly and securely attach the frame pad to the frame, and that it is in the correct position prior to using the trampoline.

8