When tightening, make sure ① that the shaft can be turned easily. the software status is displayed. we haven’ t cut any corners when it comes to the benefits they both offer. any differences between the devices are indicated specially. sipart ps2 smart electropneumatic positioner for pneumatic linear and part- turn actuators; 2-, 3-, 4- wire; 4. pdf mounting the pressure gauge and connection block 1. page 3: safety information. see manual for further messages diagnosis mode display changing the input level configure pdf diagnosis name change value using manual mode leaflet " operation - a concise overview" ( order no. these instructions are for ps2 model codes: 6dr5x1z, 6dr5x2z ( where x = 0, 1, 2, 3, 5, 6 and z = 0, 1, 2). the operations department fills the drum with the controls in manual mode. page 64: sipart ps2 valve positioner fail- safe positions. the manual contains more detailed information about assembly, function, and operation. sipart ps2 with 4 to 20 ma/ hart operating instructions, 11/, a5eae. output isolator sitrans i200 separately orderable ( 7ng4131- 1aa00). model numbers for 3- wire and 4- wire positioners are: 6dr52.
scope of delivery, see chapter 7, page 153. page 131: commissioning part- turn actuators. the siemens ps2 digital valve positioner is being used on a feedwater and startup valve for unit # 3. exit the " configuration" mode. tighten the carrier using the ⑨ ⑩ socket cap screw and the washer carrier sipart ps2 with and without hart operating instructions, 05/, a5eac. for 0- 20 ma range, positioner must be wired as 3- wire or 4- wire input current loop. sipart ps2 with and without hart operating instructions, 02/, a5eab.
after releasing the button, the positioner is in " p manual mode". 1 general information the product described in this manual left the factory in a perfectly safe and tested condition. 2 mounting a booster b. check whether the o- rings are in the pressure gauge block.
* * ) with double- action positioners view of device ( open cover) 1 input. the positioner is not initialized. 20ma with hart- interface; single action; polycarbonate enclosure standard type of protection ( ex) : intrinsic safety ( ex i). 6 is a safety- related component of the flameproof enclosure. whereas the main strength of the sipart ps100 lies in its “ ease of use” approach, flexibility is the name of the game with the sipart ps2. sipart ps2 with profibus pa operating instructions, 05/, a5eac. to do this, press the button for at least 5 seconds. place the carrier on the stump of the actuator shaft. introduction these operating instructions describe the basic steps for assembly, connection, and commissioning. sdir 7 sdir setpoint direction rising falling rise fall rise sets the action ( direction) of positioner control: direct or reverse acting with. tighten the carrier using the ⑨ ⑩ socket cap screw and the washer carrier sipart ps2 with profibus pa operating instructions, 02/, a5eab. note the following: warning siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. page 48 place the stainless steel coupling on the stump of the actuator' s positioner shaft. these operating instructions do not replace the manual for the sipart ps2 electropneumatic positioner. page 304 booster e. page 200: simulation changes become effective as soon as the transfer button is pressed.
once a positioner is properly mounted, per bracket kit instructions, verify that all. figure a- 2 slip clutch move valve so the numerical number decreases, either by pressing the button. important: refer to sipart
ps2 manuals for detailed procedures, certifications, approvals and applicable warnings and cautions. the pneumatic terminal plate on smart the sipart ps2 positioner 6dr5. proper use of siemens products. product description. never pdf loosen the screws 1 of the pneumatic terminal plate. you can smart switch the positioner to the manual mode on- site and move the actuator using buttons in this target mode also. align the positioner/ mount at the center of the actuator. 4 sipart ps2 valve positioner fail- siemens ps2 smart positioner manual pdf safe positions adjust slip clutch until number in display is within a range of: 4852. repeatability and accuracy of the valve siemens ps2 smart positioner manual pdf position in response. startup procedures call for the operator to provide an output to the feedwater valve at a prescribed level. page 45 place the stainless steel coupling on the stump of the actuator' s positioner shaft. s sipart ps2 eex d in a pressurized explosion proof housing this manual takes each of these possibilities into consideration. figure 2- 1 screws of the pneumatic terminal plate on the positioner 6dr5. if products and components from other manufacturers are used, these must be recommended or approved by siemens. sipart ps100 or sipart ps2 – you can make the choice that’ s right for you depending on your application. " man- - " is then shown on the display. a5eattention: see operating instructions for safety instructions!