SER VICE MANUAL
T4.55 S T4.65 S T4.75 S
Link Product / Engine
S Four - Wheel Drive (4WD) with cab
T4.65 S Four - Wheel Drive (4WD) with cab Australia New Zealand
S Four - Wheel Drive (4WD) with cab Australia New Zealand
Maintenance
New unit operations
[00.150] Start-up
Engine
[10.001] Engine and crankcase
[18.1 10] Clutch and components
ransmission
14] Mechanical transmission
12] Power shuttle transmission
Four-Wheel Drive (4WD) system
Mechanical control Drive (4WD) gearbox
Front axle system
[25.100] Powered front axle
Rear axle system
Powered rear axle
Power T f (PT
Rear mechanical control
Rear control
14] T rear Power T f (PT
Brakes and controls
Hydraulic service brakes
T railer brake hydraulic control
Hydraulic systems
Hydraulic systems
Remote control valves
16] hitch cylinder
Steering
[41.101] Steering control
[41.200] Hydraulic control components
[41.216] Cylinders
Cab climate control
[50.100] Heating
[50.200] Air conditioning
Electrical systems
Electrical system
Harnesses and connectors
[55.201] Engine starting system
[55.301] Alternator
[55.302]
[55.512]
[82.300]
SER VICE MANUAL
AMBRA AGRIFLU
HOLLAND AMBRA ACTIFULL™ EXTENDED LIFE COOLANT
NEW HOLLAND AMBRA UNITEK 10W -
HOLLAND AMBRA BRAKE LHM
NEW HOLLAND AMBRA MUL HYDRAULIC TRANSMISSION OIL
NEW HOLLAND AMBRA MASTER TRAN® TRACTION
AMBRA - 9 MUL - PURPOSE GREASE
New unit pre - delivery operations - Overview GENERAL INSTRUCTION
NOTE: T ake due care and attention during all maintenance and e recommend you work with a service center authorized NEW HOLLAND . Each section contains warnings for careful maintenance. not make adjustments without the necessary special Anyone who carries out procedures outside a service center responsible for those
SHIMS
When adjusting with collect the values found measuring each shim separately with a micrometer not simply consider the nominal thickness values given the shims the overall thickness the
ROT A TING SHAFT SEALS
T o correctly position the rotating shaft carry out the following steps:
Before you position the seal its soak the seal oil for least half hour ensure the seal sits its location properly
Carefully clean the shafts and ensure that the seal and contact surface are not T urn the seal that its edge moves towingard the oil. the seal oil - recycling seal, turn the seal that the grooved lip goes into the oil expelled while the shaft
Coat the seal lips with a light oil (choose engine oil rather than grease). Fill the gap between the seal lip and the dust prevention lip with (also applicable double - lip seal)
Position the seal with a flat - tipped not use a hammer
When you position the seal its ensure the seal not positioned Make sure that the seal fits snugly into its recess applying a constant pressure perpendicular the seal
When you slide the seal along the use a protective sleeve protect the seal
O - RINGS
Oil each O - ring before you position the O - When you install the O - slide the O - ring flat along the but not a leak will occur
LIQUID SEALS
Apply one the following sealants the join surfaces marked with R SILMA
RHODORSIL CAF LOCTITE PLASTIC GASKET
the following the joint surfaces before you apply the sealant:
Clean away debris thoroughly with a wire
Thoroughly clean and degrease the surfaces with a mixture hot water and soda solvent gas
BEARINGS
When you position the bearings:
Heat the bearings before you position the bearings the shaft.
Cool the bearings before you hammer the bearings into their PINS
When you position beveled spring make sure that the cut end the pin installed perpendicularly the direction Spiral spring pins can placed any
REPLACEMENT P ARTS
Only use genuine NEW HOLLAND replacement parts. Genuine parts are durable and safe.Genuine NEW HOLLAND replacement parts guarantee quality , durability , and safety
Specify the following information when you request replacement parts:
T ractor model and chassis number
Engine type and number
Part number (specified the spare parts catalog barcodes)
SER VICE T OOLS
T ools detailed the service catalog
These tools have been specially produced for NEW HOLLAND tractors.
They are essential for safe repair
They are manufactured and tested robust and ficient work tools.
Use these special tools ensure:
Optimum working conditions
The best results
T ime and energy savings
Safer operation
A TTENTION: The wear limit values recommended for some parts are provided indication only When references are made the “front”, “rear”, “right”, and “left”, these are from the driver ’ s perspective when facing forward.
AMBRA AGRIFLU
HOLLAND AMBRA ACTIFULL™ EXTENDED LIFE COOLANT
NEW HOLLAND AMBRA UNITEK 10W -
HOLLAND AMBRA BRAKE LHM
NEW HOLLAND AMBRA MUL HYDRAULIC TRANSMISSION OIL
NEW HOLLAND AMBRA MASTER TRAN® TRACTION
AMBRA - 9 MUL - PURPOSE GREASE
Start - - T echnical Data LIQUID AND OIL CAP ACITIES
Conventional coolant: NEW HOLLAND AMBRA AGRIFLU mixed % with distilled water Alternative type coolant:
HOLLAND AMBRA ACTIFULL™ EXTENDED LIFE COOLANT (If the premixed coolant not mix the concentrate with 50% distilled water)
NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please