1997 Dodge Stratus Service Repair Manual

Welcome to the 1997 Stratus (RHD & LHD) Interactive Electronic Service Manual!

CLICK ON VEHICLE TO BEGIN

tweddle litho: dom parts cdrom demo 09/96 page 1 <output:0908 ET 05/27/97>

GROUP TAB LOCATOR Introduction

0 2 3 5 6 7 8A 8B 8C 8D 8E 8F 8G 8H 8J 8K 8L 8M 8N 8P 8Q 8R 8S 8T 8U 8W 9 11 13 14 19 21 22 23 24 25

Lubrication and Maintenance Suspension Differential and Driveline Brakes Clutch Cooling System Battery Starter Charging System Ignition System Instrument Panel and Systems Audio Systems Horns Vehicle Speed Control System Turn Signal and Flashers Windshield Wipers and Washers Lamps Restraint System Electrically Heated Systems Power Door Locks Vehicle Theft Security System Power Seats Power Windows Power Mirrors Chime Warning/Reminder System Wiring Diagrams Engine Exhaust System and Intake Manifold Bumpers and Frame Fuel System Steering Transaxle Tires and Wheels Body Heating and Air Conditioning Emission Control Systems

DASH PANEL V.I.N. PLATE

17 DIGITS

WINDSHIELD OPENING

INTRODUCTION

JA

1

INTRODUCTION CONTENTS page GENERAL INFORMATION BODY CODE PLATE . . . . . . . . . . . . . . . . .

FASTENER IDENTIFICATION . . . . . . . . . . .

INTERNATIONAL VEHICLE CONTROL AND DISPLAY SYMBOLS . . . . . . . . . . . . . . . .

METRIC SYSTEM . . . . . . . . . . . . . . . . . . .

.... 1 .... 5 .... 5 .... 8

page STANDARD VEHICLE DIMENSIONS . . . . . . . . .

TORQUE REFERENCES . . . . . . . . . . . . . . . . .

VEHICLE IDENTIFICATION NUMBER . . . . . . . . .

VEHICLE SAFETY CERTIFICATION LABEL . . . .

VIN CHECK DIGIT . . . . . . . . . . . . . . . . . . . . . . .

4 10 1 1 1

GENERAL INFORMATION VEHICLE SAFETY CERTIFICATION LABEL A vehicle safety certification label (Fig. 1) is attached to the rear facing of the driverâ&#x20AC;&#x2122;s door. This label indicates date of manufacture (month and year), Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front, Gross Axle Weight Rating (GAWR) rear and the Vehicle Identification Number (VIN). The Month, Day and Hour of manufacture is also included.

All communications or inquiries regarding the vehicle should include the Month-Day-Hour and Vehicle Identification Number.

Fig. 2 Vehicle Identification Number (VINPlate)

VIN CHECK DIGIT To protect the consumer from theft and possible fraud, the manufacturer is required to include a Check Digit at the ninth position of the Vehicle Identification Number. The check digit is used by the manufacturer and government agencies to verify the authenticity of the vehicle and official documentation. The formula to use the check digit is not released to the general public.

BODY CODE PLATE Fig. 1 Vehicle Safety Certification Label

VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is located on the upper left corner of the instrument panel, near the left windshield pillar (Fig. 2). The VIN consists of 17 characters in a combination of letters and numbers that provide specific information about the vehicle. Refer to VIN Code Breakdown table for decoding information.

LOCATION AND DECODING The Body Code Plate (Fig. 3) is located in the engine compartment on the driver side strut tower.

There are seven lines of information on the body code plate. Lines 4, 5, 6, and 7 are not used to define service information. Information reads from left to right, starting with line 3 in the center of the plate to line 1 at the bottom of the plate.

PAINT ORDER VEHICLE CEDURE NUMBER PRO-

2

TRANSMISSION PRIMARY PAINT MARKET SECONDARY VIN PAINT

VINYL ROOF CAR ENGINE SHELL TRIM LINE

INTRODUCTION

JA

GENERAL INFORMATION (Continued) VIN CODE BREAKDOWN POSITION

INTERPRETATION

CODE=DESCRIPTION

1

Country of Origin

1=United States

2

Make

B=Dodge C=Chrysler P=Plymouth

3

Vehicle Type

3=Passenger Car

4

Passenger Safety

E=Active Driver and Passenger Air Bags

5

Car Line

J=Chrysler,Cirrus J=Dodge,Stratus J=Plymouth,Breeze 2=Chrysler,Stratus (sold in Mexico)

6

Series

4=High Line 5=Premium 6=Sport

7

Body Style

8

Engine

6=4 Door Sedan C=2.0L 4 Cyl 16V Gasoline SOHC X=2.4L 4 Cyl 16V Gasoline SOHC H=2.5L 6 Cyl Gasoline SOHC S=2.4L 4 Cyl 16 V DOHC Turbo (sold in Mexico)

9

Check Digit

See explanation in this section.

10

Model Year

V=1997

11 12 thru 17

Assembly Plant

N=Sterling Heights Assembly

Sequence Number

6 digit number assigned by assembly plant.

DIGITS 16, 17, AND 18 Vehicle Shell Line • JACP= Chrysler, Cirrus • JADH= Dodge, Stratus • JADP=Dodge, Stratus ES • JAPH=Plymouth, Breeze DIGIT 19 Price Class • E = Economy • H = High Line • L = Low Line • M = Mid Line • P = Premium • S = Special/Sport • X = Performance Image

BODY CODE PLATE—LINE 3

DIGITS 20 AND 21 Body Type • 41=Four Door Sedan

DIGITS 1 THROUGH 12 Vehicle Order Number

BODY CODE PLATE LINE 2

Fig. 3 Body Code Plate

DIGITS 13, 14, AND 15 Vinyl Roof Code

DIGITS 1, 2, AND 3— Paint procedure

INTRODUCTION

JA

3

GENERAL INFORMATION (Continued) DIGIT 4— Open Space

• DGL = 41TE 4-speed Electronic Automatic Transaxle • DD5 = NV T350 5-Speed Manual Transaxle

DIGITS 5 THROUGH 8— Primary paint See Group 23, Body for color codes.

DIGIT 4— Open Space

DIGIT 9— Open Space DIGITS 10 THROUGH 13— Secondary Paint DIGIT 14— Open Space DIGITS 15 THROUGH 18— Interior Trim Code DIGIT 19— Open Space DIGITS 20, 21, AND 22— Engine Code • ECB = 2.0L Four Cylinder SOHC Gasoline • EEB = 2.5L Six Cylinder SOHC Gasoline • EDZ = 2.4L Four Cylinder DOHC Gasoline

BODY CODE PLATE LINE 1 DIGITS 1, 2, AND 3— Transaxle Codes

DIGIT 5— Market Code • U = United States • C = Canada • B = International • M = Mexico DIGIT 6— Open Space DIGITS 7 THROUGH 23— Vehicle Identification Number • Refer to Vehicle Identification Number (VIN) paragraph for proper breakdown of VIN code.

IF TWO BODY CODE PLATES ARE REQUIRED The last code shown on either plate will be followed by END. When two plates are required, the last code space on the first plate will indicate (CTD) When a second plate is required, the first four spaces of each line will not be used due to overlap of the plates.

4

INTRODUCTION

JA

GENERAL INFORMATION (Continued)

STANDARD VEHICLE DIMENSIONS INTERIOR DIMENSIONS BODY STYLE CP-41 DP-41 DH-41 PH-41

HEAD ROOM FRONT

LEG ROOM

REAR

FRONT

REAR

SHOULDER ROOM FRONT

REAR

HIP ROOM FRONT

REAR

38.1 in.

36.8 in.

42.3 in.

38.1 in.

55.2 in.

54.7 in.

52.8 in.

52.7 in.

967 mm

935 mm

1075 mm

968 mm

1403 mm

1390 mm

1341 mm

1338 mm

38.1 in.

36.8 in.

42.3 in.

38.1 in.

55.2 in.

54.7 in.

52.8 in.

52.7 in.

967 mm

935 mm

1075 mm

968 mm

1403 mm

1390 mm

1341 mm

1338 mm

38.1 in.

36.8 in.

42.3 in.

38.1 in.

55.2 in.

54.7 in.

52.8 in.

52.7 in.

967 mm

935 mm

1075 mm

968 mm

1403 mm

1390 mm

1341 mm

1338 mm

38.1 in.

36.8 in.

42.3 in.

38.1 in.

55.2 in.

54.7 in.

52.8 in.

52.7 in.

967 mm

935 mm

1075 mm

968 mm

1403 mm

1390 mm

1341 mm

1338 mm

EXTERIOR DIMENSIONS WHEEL BASE

FRONT TRACK

REAR TRACK

OVERALL LENGTH

OVERALL WIDTH

OVERALL HEIGHT

MM-IN.

MM-IN.

MM-IN.

MM-IN.

MM-IN.

MM-IN.

CP-41

2743-108.0

1528-60.2

1528-60.2

4750-187.0

1804-71.0

1384-54.5

DP-41

2743-108.0

1528-60.2

1528-60.2

4725-186.0

1804-71.0

1374-54.5

DH-41

2743-108.0

1528-60.2

1528-60.2

4725-186.0

1804-71.0

1374-54.1

PH-41

2743-108.0

1528-60.2

1528-60.2

4742-186.0

1804-71.0

1374-54.1

BODY STYLE

WINDSHIELD WINDSCREEN ENGINE BATTERY HEADLIGHTS, REAR REAR LIGHTS, REAR WINDSHIELD REAR WINDOW WINDSHIELD COOLANT HAZARD WINDOW AND VENTILATING CHARGING PARKING WINDOW BRAKE HOOD PANEL TURN FRONT DEFROSTING WIPER FOG ENGINE HIGH DEFOGGER DEMISTING SEAT WARNING TEMPERPARKING WASHER LIGHTER FAILURE (TRUNK) SIGNAL LIGHTS DITION BRAKE ATURE WIPER HOOD HORN BEAM FUEL CONBELT AND FAN OIL

THREAD INCHES DIAMETER MAJOR IN

NUMBER THREADS 5/16-18 INCH INCH PER OF

THREADLIMETERS DIAMETER MAJOR IN MIL- DISTANCE THREADS BETWEEN M8METRIC X LIMETERS 1.25 IN MIL-

INTRODUCTION

JA

5

GENERAL INFORMATION (Continued)

INTERNATIONAL VEHICLE CONTROL AND DISPLAY SYMBOLS INTERNATIONAL VEHICLE CONTROL AND DISPLAY SYMBOLS The graphic symbols illustrated in the following chart (Fig. 4) are used to identify various instrument controls. The symbols correspond to the controls and displays that are located on the instrument panel.

FASTENER IDENTIFICATION

Fig. 5 Thread Notationâ&#x20AC;&#x201D;SAE and Metric

FASTENER IDENTIFICATION THREAD IDENTIFICATION SAE and metric bolt/nut threads are not the same.

The difference is described in the Thread Notation chart (Fig. 5).

GRADE/CLASS IDENTIFICATION The SAE bolt strength grades range from grade 2 to grade 8. The higher the grade number, the greater the bolt strength. Identification is determined by the

line marks on the top of each bolt head. The actual bolt strength grade corresponds to the number of line marks plus 2. The most commonly used metric bolt strength classes are 9.8 and 12.9. The metric strength class identification number is imprinted on the head of the bolt. The higher the class number, the greater the bolt strength. Some metric nuts are imprinted with a single-digit strength class on the nut face. Refer to the Fastener Identification and Fastener Strength Charts.

INTERNATIONAL CONTROL AND DISPLAY SYMBOLS

Fig. 4

6

INTRODUCTION

JA

GENERAL INFORMATION (Continued) FASTENER IDENTIFICATION

HOW Hexagon bolt Two lines Hexagon bolt Welded flange hexagon w/washer No TO mark protruding DETERMINE bolt bolt head bolt head BOLT STRENGTH

BoltHexagon flange hexagon w/washer No Grooved bolt Four lines Hexagon head mark protruding bolt No. bolt head Mark

Class

Three Stud bolt protruding lines

Hexagon Mark head No bolt mark

Class

INTRODUCTION

JA GENERAL INFORMATION (Continued) FASTENER STRENGTH

7

1 COMMON Cubic Cubic Cubic 1 =1Inch Mile Kilometers/Hr. Newton-Meters Inch Foot = Yard =1METRIC ==Meters/Sec. Kilopascals Inches Yard Foot == Millimeters Kilometers =16 = 1.6 25 Kilometers/Hr. ====0.03 Cubic Meters 0.8 Millimeters Kilometers Inches Hg 0.3 0.9 Feet/Sec. EQUIVA==timeters == LENTS To = (Km/h) Inches (60°F) ft.-lbs. in-lbs.

Meter Cubic Yards (N·m) (M/S) (kPa) Miles Km/h (mm) =Cen(Km) Feet mph N·m M/S kPa Get mm Km (M) Multiply psi Hg To M Get

8

By

Multiply By

INTRODUCTION

JA

GENERAL INFORMATION (Continued) CONVERSION FORMULAS AND EQUIVALENT VALUES

METRIC SYSTEM WARNING: USE OF AN INCORRECT FASTENER MAY RESULT IN COMPONENT DAMAGE OR PERSONAL INJURY. Figure art, specifications and torque references in this Service Manual are identified in metric and SAE format.

During any maintenance or repair procedures, it is important to salvage metric fasteners (nuts, bolts, etc.) for reassembly. If the fastener is not salvageable, a fastener of equivalent specification should be used.

The metric system is based on quantities of one, ten, one hundred, one thousand and one million (Fig. 6).

The following chart will assist in converting metric units to equivalent English and SAE units, or vise versa.

Fig. 6 Metric Prefixes Refer to the Conversion Chart to convert torque values listed in metric Newton- meters (N·m). Also, use the chart to convert between millimeters (mm) and inches (in.)

INTRODUCTION

JA GENERAL INFORMATION (Continued)

METRIC CONVERSION

9

Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING

NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.

10

INTRODUCTION

JA

GENERAL INFORMATION (Continued)

TORQUE REFERENCES Individual Torque Charts appear at the end of many Groups. Refer to the Standard Torque Specifi-

cations Chart for torque references not listed in the individual torque charts.

TORQUE SPECIFICATIONS

ENGINE TRANSMISSION AUTOMATIC ENGINE COOLANT FLUID OIL

WINDSHIELD POWER BRAKE WASHER STEERING FLUID FLUID FLUID

LUBRICATION AND MAINTENANCE

JA

0-1

LUBRICATION AND MAINTENANCE CONTENTS page

page

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . 1 JUMP STARTING, HOISTING AND TOWING . . . 7

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . 3

GENERAL INFORMATION INDEX page

page

GENERAL INFORMATION CLASSIFICATION OF LUBRICANTS . . . . . . . . . . 1 FLUID CAPACITIES . . . . . . . . . . . . . . . . . . . . . . 2 INTERNATIONAL SYMBOLS . . . . . . . . . . . . . . . 1

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . 1 PARTS AND LUBRICANT RECOMMENDATIONS ....................................... 1

GENERAL INFORMATION

INTERNATIONAL SYMBOLS

INTRODUCTION

Chrysler Corporation uses international symbols to identify engine compartment lubricant and fluid inspection and fill locations (Fig. 1).

Service and maintenance procedures for components and systems listed in Schedule—A or B can be found by using the Group Tab Locator index at the front of this manual. If it is not clear which group contains the information needed, refer to the index at the back of this manual.

There are two maintenance schedules that show proper service based on the conditions that the vehicle is subjected to.

Schedule— A , lists scheduled maintenance to be performed when the vehicle is used for general transportation.

Schedule— B , lists maintenance intervals for vehicles that are operated under the conditions listed at the beginning of the Maintenance Schedule section.

Use the schedule that best describes your driving conditions.

Where time and mileage are listed, follow the interval that occurs first.

PARTS AND LUBRICANT RECOMMENDATIONS When service is required, Chrysler Corporation recommends that only Mopart brand parts, lubricants and chemicals be used. Mopar provides the best engineered products for servicing Chrysler Corporation vehicles.

Fig. 1 International Symbols

CLASSIFICATION OF LUBRICANTS Only lubricants that are endorsed by the following organization should be used to service a Chrysler Corporation vehicle.

• Society of Automotive Engineers (SAE) • American Petroleum Institute (API) (Fig. 2) • National Lubricating Grease Institute (NLGI) (Fig. 3)

0-2

LUBRICATION AND MAINTENANCE

JA

GENERAL INFORMATION (Continued) Wheel bearing lubricant is identified by the letter “G”. Chassis lubricant is identified by the latter “L”.

The letter following the usage letter indicates the quality of the lubricant. The following symbols indicate the highest quality.

Fig. 2 API Symbol ENGINE OIL SAE GRADE RATING INDICATES ENGINE OIL VISCOSITY An SAE viscosity grade is used to specify the viscosity of engine oil. SAE 30 specifies a single viscosity engine oil. Engine oils also have multiple viscosities. These are specified with a dual SAE viscosity grade which indicates the cold-to-hot temperature viscosity range.

• SAE 30 = single grade engine oil.

• SAE 10W-30 = multiple grade engine oil.

API QUALITY CLASSIFICATION The API Service Grade specifies the type of performance the engine oil is intended to provide. The API Service Grade specifications also apply to energy conserving engine oils.

Use engine oils that are API Service Certified.

5W-30 and 10W-30 MOPAR engine oils conform to specifications.

Refer to Group 9, Engine for engine oil specification.

GEAR LUBRICANTS SAE ratings also apply to multiple grade gear lubricants. In addition, API classification defines the lubricants usage.

LUBRICANTS AND GREASES Lubricating grease is rated for quality and usage by the NLGI. All approved products have the NLGI symbol (Fig. 3) on the label. At the bottom NLGI symbol is the usage and quality identification letters.

Fig. 3 NLGI Symbol

FLUID CAPACITIES FUEL TANK All . . . . . . . . . . . . . . . . . . . . . . . . . 60.5 L (16.0 gal.)

ENGINE OIL—WITH FILTER 2.0L, 2.5L V6 . . . . . . . . . . . . . . . . . . 4.25 L (4.5 qts.)

2.4L . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 L (5.0 qts.)

ENGINE OIL—WITHOUT FILTER 2.0L, 2.5L V6 . . . . . . . . . . . . . . . . . . . 3.8 L (4.0 qts.)

2.4L . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 L (4.5 qts.)

COOLING SYSTEM 2.0 L . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 L (8.5 qts.)

2.4 L . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 L (9.0 qts.)

2.5 L . . . . . . . . . . . . . . . . . . . . . . . . 9.9 L (10.5 qts.)

AUTOMATIC TRANSAXLE Estimated Service Fill . . . . . . . . . . . . 3.8 L (4.0 qts.)

Overhaul Fill Capacity with Torque Converter Empty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6 L (9.1 qts.)

MANUAL TRANSAXLE NV T350 . . . . . . . . . . . . . . . . . . . . . . 2.1 L (2.2 qts.)

LUBRICATION AND MAINTENANCE

JA

0-3

MAINTENANCE SCHEDULES INDEX page

page

GENERAL INFORMATION INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . 3 SCHEDULE—A . . . . . . . . . . . . . . . . . . . . . . . . . 3

SCHEDULE—B . . . . . . . . . . . . . . . . . . . . . . . . . 4 UNSCHEDULED INSPECTION . . . . . . . . . . . . . . 3

GENERAL INFORMATION INTRODUCTION There are two maintenance schedules that show the proper service for Chrysler vehicles. Use the schedule that best describes the conditions under which the vehicle is operated. Where time and mileage are listed, follow the interval that occurs first.

Schedule—A lists all the scheduled maintenance to be performed under “normal” operating conditions.

Schedule—B is a schedule for vehicles that are operated under one or more of the following conditions: • Day and night temperatures are below freezing.

• Stop and go driving.

• Long periods of engine idling.

• Driving in dusty conditions.

• Short trips of less than 5 miles.

• Operation at sustained high speeds during hot weather, above 90°F (32°C).

• Taxi, police or delivery service.

• Trailer towing or heavy hauling.

EMISSION CONTROL SYSTEM MAINTENANCE The scheduled emission maintenance listed in bold type in the Maintenance Schedules must be done at the specified mileage to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide the best vehicle performance and reliability. More frequent maintenance may be needed for vehicles in severe operating conditions such as dusty areas and very short trip driving.

UNSCHEDULED INSPECTION At Each Stop For Fuel • Check engine oil level, add as required.

• Check windshield washer solvent and add if required.

Once A Month • Check tire pressure and look for unusual wear or damage.

• Check fluid levels of coolant reservoir, power steering and automatic transmission and add as required.

• Check all lights and all other electrical items for correct operation.

At Each Oil Change • Inspect exhaust system.

• Inspect brake hoses.

• Inspect the CV joints and front suspension components.

• Rotate the tires at each oil change interval shown on Schedule—A (7,500 miles – 12 000 km) or every other interval shown on schedule—B (6,000 miles – 10 000 km).

• Check coolant level, hoses and clamps.

• Check the manual transaxle fluid level.

• If the mileage is less than 7,500 miles (12 000 km) yearly, replace the engine oil filter at each oil change.

SCHEDULE—A 7,500 Miles (12 000 km) or at 6 months • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

15,000 Miles (24 000 km) or at 12 months • Change engine oil.

• Replace engine oil filter.

• Adjust drive belt tension.

22,500 Miles (36 000 km) or at 18 months • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

• Inspect the front brake pads and rear brake linings.

30,000 Miles (48 000 km) or at 24 months • Change engine oil.

• Replace engine oil filter on all engines.

• Lubricate front and rear suspension ball joints.

• Adjust drive belt tension.

0-4

LUBRICATION AND MAINTENANCE

JA

GENERAL INFORMATION (Continued) • Replace air cleaner element.

• Replace spark plugs on 2.0L and 2.4L engines.

• Flush and replace engine coolant if it has been 30,000 miles (48 000 km) or 24 months since last change.

37,500 Miles (60 000 km) or at 30 months • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

90,000 Miles (144 000 km) or at 72 months • Change engine oil.

• Replace engine oil filter on all engines.

• Check and replace, if necessary***, the PCV valve.** • Lubricate front and rear suspension upper ball joints.

• Inspect front brake pads and rear brake linings.

• Adjust drive belt tension.

• Replace air cleaner air cleaner element.

• Replace spark plugs on 2.0L and 2.4L engines.

45,000 Miles (72 000 km) or at 36 months • Change engine oil.

• Replace engine oil filter on all engines.

• Inspect front brake pads and rear brake linings.

• Adjust drive belt tension.

• Flush and replace engine coolant at 36 months, regardless of mileage.

52,500 Miles (84 000 km) or at 42 months • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

• Flush and replace engine coolant if not done at 36 months, regardless of mileage.

60,000 Miles (96 000 km) or at 48 months • Change engine oil.

• Replace engine oil filter on all engines.

• Check and replace, if necessary***, the PCV valve.** • Lubricate front and rear suspension upper ball joints.

• Replace drive belts.

• Replace air cleaner element.

• Replace ignition cables on 2.0 liter and 2.4 liter engines.

• Replace spark plugs on 2.0L and 2.4L engines.

67,500 Miles (108 000 km) or at 54 months • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

• Inspect front brake pads and rear brake linings.

75,000 Miles (120 000 km) or at 60 months • Change engine oil.

• Replace engine oil filter on all engines.

• Adjust drive belt tension.

• Flush and replace engine coolant if it has been 30,000 miles (48 000 km) or 24 months since last change.

82,500 Miles (132 000 km) or at 66 months • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

97,500 Miles (156 000 km) or at 78 months • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

100,000 Miles (160 000km) • Replace spark plugs and ignition cables on 2.5L engines.

105,000 Miles (168 000 km) • Change engine oil.

• Replace engine oil filter on all engines.

• Replace engine timing belt on 2.0 liter and 2.4 liter California vehicles.

SCHEDULE—B 3,000 Miles (5 000 km) • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

6,000 Miles (10 000 km) • Change engine oil • Replace engine oil filter on all engines.

9,000 Miles (14 000 km) • Change engine oil.

• Replace engine oil filter on 2.0 liter and 2.4 liter engines.

12,000 Miles (19 000 km) • Change engine oil • Replace engine oil filter on all engines.

• Inspect front brake pads and rear brake linings.

15,000 Miles (24 000 km) • Change engine oil • Replace engine oil filter on 2.0 liter and 2.4 liter engines.