BOBCAT T180 COMPACT TRACK LOADER Service Repair Manual SN A3LL11001 & Above

Service Manual T180 Compact Track Loader S/N A3LL11001 & Above

EQUIPPED WITH BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) 6987051 (8-08)

Printed in U.S.A.

© Bobcat Company 2008

MAINTENANCE SAFETY WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow W-2003-0903 instructions can cause injury or death.

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

CORRECT

CORRECT

CORRECT

B-10731a

B-15659

B-15660

Never service the Bobcat Compact Track Loader without instructions.

Use the correct procedure to lift or lower operator cab.

Cleaning and maintenance are required daily.

WRONG

WRONG

WRONG

B-15664

B-15661

B-15662

Have good ventilation when welding or grinding painted parts.

Wear dust mask when grinding painted parts. Toxic dust and gas can be produced.

Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed.

WRONG

B-15665

Stop, cool and clean engine of flammable materials before checking fluids.

Never service or adjust loader with the engine running unless instructed to do so in the manual.

Avoid contact with leaking hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes.

Never fill fuel tank with engine running, while smoking or when near open flame.

Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported by an approved lift arm support device.

Replace it if damaged.

Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged.

Never modify equipment or add attachments not approved by Bobcat Company.

WRONG

WRONG

B-15663

Keep body, jewelry and clothing away from moving parts, electrical contact, hot parts and exhaust.

Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used.

Use eye protection approved for type of welding.

Keep rear door closed except for service. Close and latch door before operating the loader.

B-6589

Lead-acid batteries produce flammable and explosive gases.

Keep arcs, sparks, flames and lighted tobacco away from batteries.

Batteries contain acid which burns eyes or skin on contact.

Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate medical attention.

Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/ operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer.

MSW09-0805

ALPHABETICAL INDEX ACCESS PANEL (INSIDE) ..................................... 50-01 ACCESS PANEL (INSIDE) (SJC) ........................... 50-01 AIR CLEANER ........................................................70-01 AIR CLEANER SERVICE .......................................10-01 AIR CONDITIONING SYSTEM FLOW ................... 80-01 ALTERNATOR ........................................................ 60-01 BACK-UP ALARM SYSTEM ................................... 60-01 BATTERY................................................................ 60-01 BLOWER FAN ........................................................ 80-01 BOBCAT INTERLOCK CONTROL SYSTEM (BICS) ................................................... 60-01 BOBCAT CONTROLLER (ACS) ............................ 60-01 BOBCAT CONTROLLER (GATEWAY AND AUXILIARY).................................................. 60-01 BOBCAT CONTROLLER (SJC) (DRIVE) ............... 60-01 BOB-TACH (HAND LEVER) ........................ 10-01, 50-01 BOB-TACH (POWER).................................. 10-01, 50-01 BOB-TACH (POWER) BLOCK................................ 20-01 BRAKE .................................................................... 40-01 BUCKET POSITION VALVE.................................. 20-01 CAB DOOR ............................................................. 50-01 CALIBRATION ........................................................ 60-01 CAMSHAFT AND TIMING GEARS......................... 70-01 CASE DRAIN FILTER ............................................. 30-01 CHARGE PRESSURE ........................................... 30-01 COMPRESSOR ...................................................... 80-01 CONDENSER ......................................................... 80-01 CONTROL HANDLE/LEVER .................................. 50-01 CONTROL HANDLE/LEVER (ACS) ....................... 50-01 CONTROL HANDLE/LEVER (SJC) ........................ 50-01 CONTROL PANEL .................................................. 50-01 CONTROL PANEL (SJC)........................................ 50-01 CONTROL PANEL SETUP ..................................... 60-01 CONTROL PEDALS AND LINKAGE ...................... 50-01 CONTROL PEDALS (ACS) .................................... 50-01 CONTROL SYSTEM (ACS) .................................... 60-01 CONVERSIONS ................................................SPEC-01 CRANKSHAFT AND PISTONS ............................. 70-01 CYLINDER (LIFT) ................................................... 20-01 CYLINDER (BOB-TACH) ........................................ 20-01 CYLINDER (TILT) ................................................... 20-01 CYLINDER HEAD ................................................... 70-01

ELECTRICAL/HYD. CONTROLS ............................60-01 ELECTRICAL/HYD. CONTROLS REFERENCE (SJC) ..............................................60-01 ELECTRICAL SYSTEM INFORMATION.................60-01 ENGINE COOLING SYSTEM .................................10-01 ENGINE LUBRICATION SYSTEM .........................10-01 ENGINE COOLING SYSTEM .................................70-01 ENGINE INFORMATION .........................................70-01 ENGINE SPEED CONTROL ...................................70-01 ENGINE SPEED CONTROL (SJC) .........................70-01 EVAPORATOR ........................................................80-01 EVAPORATOR/HEATER UNIT................................80-01 EXHAUST GAS RECIRCULATION (EGR) SYSTEM.....................................................70-01 EXPANSION VALVE ................................................80-01 FLYWHEEL AND HOUSING ...................................70-01 FLYWHEEL RPM SENSOR ....................................60-01 FRONT AUXILIARY HYDRAULIC COUPLER BLOCK ...............................................20-01 FUEL SYSTEM.............................................10-01, 70-01 FUEL TANK .............................................................50-01 HEATER COIL .........................................................80-01 HEATER VALVE ......................................................80-01 HIGH FLOW VALVE ................................................20-01 HYDRAULIC CONNECTION SPECS ............... SPEC-01 HYDRAULIC CONTROL VALVE (ACS) OR (SJC) ..20-01 HYDRAULIC CONTROL VALVE (STANDARD) ......20-01 HYDRAULIC/HYDROSTATIC FILTERS ..................20-01 HYDRAULIC FLUID RESERVOIR ..........................20-01 HYDRAULIC/HYDROSTATIC FLUID SPECIFICATIONS................................ SPEC-01 HYDRAULIC/HYDROSTATIC SYSTEM..................10-01 HYDRAULIC PUMP (STANDARD)..........................20-01 HYDRAULIC PUMP (STANDARD) (HIGH FLOW)..20-01 HYDRAULIC PUMP (SJC) ......................................20-01 HYDRAULIC PUMP (SJC) (HIGH FLOW)...............20-01 HYDRAULIC SYSTEM INFORMATION ..................20-01 HYDROSTATIC MOTOR .........................................30-01 HYDROSTATIC PUMP ............................................30-01 HYDROSTATIC PUMP (SJC) ..................................30-01 HYDROSTATIC SYSTEM INFORMATION..............30-01 INSTRUMENT PANELS .........................................60-01

DIAGNOSTICS SERVICE CODES......................... 60-01 DRIVE BELT ........................................................... 30-01

LIFT ARMS ..............................................................50-01 LIFT ARM BYPASS CONTROL VALVE ..................20-01 LIFT ARM SUPPORT DEVICE................................10-01 LIFTING AND BLOCKING THE LOADER...............10-01 LIGHTS....................................................................60-01 T180 LOADER SPECIFICATIONS .................... SPEC-01 LOADER STORAGE AND RETURN TO SERVICE 10-01 LUBRICATING THE LOADER.................................10-01 LUBRICATION SYSTEM .........................................70-01

ALPHABETICAL INDEX (CONT’D) MAIN RELIEF VALVE ..............................................20-01 MAINTENANCE CLOCK .........................................60-01 MUFFLER................................................................70-01 OIL COOLER...........................................................20-01 OPERATOR CAB..........................................10-01, 50-01 OPERATOR SEAT (SUSPENSION)........................50-01 PASSWORD SETUP (IF EQUIPPED WITH KEYLESS START).................................................60-01 PIVOT PINS.............................................................10-01 REAR AUXILIARY DIVERTER VALVE ....................20-01 REAR DOOR ..........................................................50-01 REAR GRILL ..........................................................50-01 RECEIVER/DRIER ..................................................80-01 REGULAR MAINTENANCE ....................................80-01 REMOTE STARTTOOL KIT-MEL1563 ....................10-01 REMOTE START TOOL (SERVICE TOOL) KIT-6689779 ..........................................................10-01 SEAT BAR............................................................... 50-01 SEAT BAR SENSOR............................................... 60-01 SERVICE PC (LAPTOP COMPUTER) ....................60-01 SERVICE SCHEDULE.............................................10-01 SPARK ARRESTOR MUFFLER ..............................10-01 SPEED SENSOR (SJC) ..........................................60-01 STARTER ................................................................60-01 STEERING DRIFT COMPENSATION .....................60-01 STOPPING THE ENGINE AND LEAVING THE LOADER .......................................10-01 SYSTEM CHARGING AND RECLAMATION ..........80-01 TEMPERATURE/PRESSURE .................................80-01 THERMOSTAT.........................................................80-01 TORQUE SPECIFICATIONS FOR BOLTS........ SPEC-01 TOWING THE LOADER ..........................................10-01 TRACK CARRIAGE COMPONENTS ......................40-01 TRACTION LOCK....................................................60-01 TRANSPORTING THE LOADER ON A TRAILER ..10-01 TROUBLESHOOTING.............................................80-01 TURBOCHARGER ..................................................70-01 WINDOW (FRONT DOOR) .....................................50-01 WINDOW (REAR)....................................................50-01 WINDOW (SIDE) .....................................................50-01 WINDOW (TOP) ......................................................50-01

SAFETY & MAINTENANCE

CONTENTS FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V

HYDRAULIC SYSTEM

FIRE PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VII SERIAL NUMBER LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX

HYDROSTATIC SYSTEM

DELIVERY REPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X LOADER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XI SAFETY & MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-01

DRIVE SYSTEM

HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-01 MAIN FRAME HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-01 DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-01 MAIN FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-01

ELECTRICAL SYSTEM & ANALYSIS

ELECTRICAL SYSTEM & ANALYSIS. . . . . . . . . . . . . . . . . . . . . 60-01 ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-01

ENGINE SERVICE

HEATING, VENTILATION, AIR CONDITIONING . . . . . . . . . . . . 80-01 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-01

HVAC

SPECIFICATIONS

SPECIFICATIONS

I

T180 Service Manual

FOREWORD This manual is for the Bobcat loader mechanic. It provides necessary servicing and adjustment procedures for the Bobcat loader and its component parts and systems. Refer to the Operation & Maintenance Manual for operating instructions, starting procedure, daily checks, etc.

A general inspection of the following items must be made after the loader has had service or repair: 1. Check that the ROPS/FOPS (Including side screens) is in good condition and is not modified.

9. The parking brake function correctly.

2. Check that ROPS mounting hardware is tightened and is Bobcat approved.

10. Enclosure door latches must open and close freely.

3. The seat belt must be correctly installed, functional and in good condition.

11. Bob-Tach wedges and linkages must function correctly and be in good condition.

4. The seat bar must be correctly adjusted, clean and lubricated.

12. Safety treads must be in good condition.

5. Check lift arm support device, replace if damaged.

13. Check for correct function of indicator lamps.

6. Machine signs (decals) must be legible and in the correct location.

14. Check hydraulic fluid level, engine oil level and fuel supply.

7. Steering levers, hand controls and foot pedals must return to neutral (as applicable).

15. Inspect for fuel, hydraulic fluid leaks.

8. Check for correct function of the work lights.

16. Lubricate the loader.

must

oil

or

FW SSL-0308 SM II

T180 Service Manual

17. Check the condition of the battery and cables.

22. Check for any field modification not completed.

18. Inspect the air cleaner for damage or leaks. Check the condition of the element.

23. Operate the machine and check all functions.

19. Check the electrical charging system.

24. Check for correct function of the Bobcat Interlock Control System (BICS™) before the machine is returned to the customer.

20. Check tires for wear and pressure. Check tracks for wear and tension. Use only approved tires or tracks.

25. Check function or condition of all equipped options and accessories (examples: backup alarm, fire extinguisher, rotating beacon, lift kits, etc.).

21. Inspect for loose or broken parts or connections.

26. Recommend to the owner that all necessary corrections be made before the machine is returned to service.

CALIFORNIA PROPOSITION 65 WARNING Diesel engine exhaust and some of its constituents are known to the state of California to cause cancer, birth defects and other reproductive harm.

FW SSL-0308 SM III

T180 Service Manual

SAFETY INSTRUCTIONS

The following publications provide information on the safe use and maintenance of the Bobcat machine and attachments:

Safety Alert Symbol This symbol with a warning statement means: “Warning, be alert! Your safety is involved!”

Carefully read the message that follows.

•

The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine is in safe operating condition.

•

The Operation & Maintenance Manual delivered with the machine or attachment contains operating information as well as routine maintenance and service procedures. It is a part of the machine and can be stored in a container provided on the machine.

Replacement Operation & Maintenance Manuals can be ordered from your Bobcat dealer.

•

Machine signs (decals) instruct on the safe operation and care of your Bobcat machine or attachment. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat dealer.

•

An Operator’s Handbook fastened to the operator cab. It’s brief instructions are convenient to the operator. The handbook is available from your dealer in an English edition or one of many other languages.

See your Bobcat dealer for more information on translated versions.

•

The AEM Safety Manual delivered with the machine gives general safety information.

•

The Service Manual and Parts Manual are available from your dealer for use by mechanics to do shoptype service and repair work.

•

The Skid-Steer Loader Operator Training Course is available through your local dealer or at www.training.bobcat.com or www.bobcat.com.

This course is intended to provide rules and practices of correct operation of the Skid-Steer Loader. The course is available in English and Spanish versions.

•

Service Safety Training Courses are available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com. They provide information for safe and correct service procedures.

•

The Skid-Steer Loader Safety Video is available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com.

WARNING Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service.

Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0903

IMPORTANT This notice identifies procedures which must be followed to avoid damage to the machine.

I-2019-0284

DANGER The signal word DANGER on the machine and in the manuals indicates a hazardous situation which, if not avoided, will result in death or serious injury.

D-1002-1107

WARNING The signal word WARNING on the machine and in the manuals indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

W-2044-1107

SI SSL-0308 SM V

T180 Service Manual

SAFETY INSTRUCTIONS (CONT’D) The dealer and owner / operator review the recommended uses of the product when delivered. If the owner / operator will be using the machine for a different application(s) he or she must ask the dealer for recommendations on the new use.

Cutting or drilling concrete containing sand or rock containing quartz may result in exposure to silica dust.

Do not exceed Permissible Exposure Limits (PEL) to silica dust as determined by OSHA or other job site Rules and Regulations. Use a respirator, water spray or other means to control dust. Silica dust can cause lung disease and is known to the state of California to cause cancer.

Call Before You Dig Dial 811 (USA Only) 1-888-258-0808 (USA & Canada) When you call, you will be directed to a location in your state / province, or city for information about buried lines (telephone, cable TV, water, sewer, gas, etc.).

SI SSL-0308 SM

VI

T180 Service Manual

Hydraulic System

FIRE PREVENTION

Check hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Hydraulic tubes and hoses must be properly routed and have adequate support and secure clamps.

Tighten or replace any parts that show leakage.

Maintenance

Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.

The machine and some attachments have components that are at high temperatures under normal operating conditions. The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a source of arcs or sparks.

Fueling

Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it can cause a fire hazard. Clean often to avoid this accumulation. Flammable debris in the engine compartment is a potential fire hazard.

Stop the engine and let it cool before adding fuel. No smoking! Do not refuel a machine near open flames or sparks. Fill the fuel tank outdoors.

The operator’s area, engine compartment and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazards and overheating.

Starting Do not use ether or starting fluids on any engine that has glow plugs. These starting aids can cause explosion and injure you or bystanders.

All fuels, most lubricants and some coolants mixtures are flammable. Flammable fluids that are leaking or spilled onto hot surfaces or onto electrical components can cause a fire.

Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting.

Operation Do not use the machine where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases.

Spark Arrestor Exhaust System The spark arrestor exhaust system is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the exhaust gases are still hot.

Electrical

Check the spark arrestor exhaust system regularly to make sure it is maintained and working properly. Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrestor muffler (if equipped).

Check all electrical wiring and connections for damage.

Keep the battery terminals clean and tight. Repair or replace any damaged part or wires that are loose or frayed.

Battery gas can explode and cause serious injury. Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting. Do not jump start or charge a frozen or damaged battery. Keep any open flames or sparks away from batteries. Do not smoke in battery charging area.

SI SSL-0308 SM

VII

T180 Service Manual

FIRE PREVENTION (CONT’D) Welding And Grinding Always clean the machine and attachment, disconnect the battery, and disconnect the wiring from the Bobcat controllers before welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the machine when welding.

Have good ventilation when grinding or welding painted parts. Wear dust mask when grinding painted parts.

Toxic dust or gas can be produced.

Dust generated from repairing nonmetallic parts such as hoods, fenders or covers can be flammable or explosive.

Repair such components in a well ventilated area away from open flames or sparks.

Fire Extinguishers

Know where fire extinguishers and first aid kits are located and how to use them. Inspect the fire extinguisher and service the fire extinguisher regularly.

Obey the recommendations on the instructions plate.

SI SSL-0308 SM VIII

T180 Service Manual

SERIAL NUMBER LOCATION

Engine Serial Number

Always use the serial number of the loader when requesting service information or when ordering parts.

Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

Figure 2

Loader Serial Number Figure 1

P-48002

The engine serial number is in the location shown [Figure 2].

P-45263

The loader serial number plate is located on the outside of the loader frame [Figure 1].

Explanation of loader Serial Number: XXXX Model 1.-Model/ Engine Combination

XXXXX Model 2.-Production Sequence (Series)

1. The four digit Model/Engine Combination Module number identifies the model number and engine combination.

2. The five digit Production Sequence Number identifies the order which the loader is produced.

IX

T180 Service Manual

DELIVERY REPORT Figure 3

B-16315

The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [Figure 3].

X

T180 Service Manual

LOADER IDENTIFICATION

FRONT LIGHTS

SEAT BAR OPERATOR SEAT with SEAT BELT

GRAB HANDLES STEERING LEVERS TILT CYLINDERS FRONT AUXILIARY QUICK COUPLERS

BUCKET STEPS

STEPS WITH SAFETY TREAD B-19882A

† BUCKET ◆ REAR WINDOW

● OPERATOR CAB

(ROPS / FOPS) LIFT ARM SUPPORT DEVICE

◆ REAR AUXILIARY

QUICK COUPLERS

LIFT ARM REAR GRILL

LIFT CYLINDER

REAR DOOR ◆ REAR

LIGHT ◆ TAIL

LIGHT ◆

❒ † ●

❒ TRACKS

B-19883

OPTIONAL OR FIELD ACCESSORY (Not Standard Equipment) TRACKS - Optional tracks are available.

Bucket - Several different buckets and other attachments are available for this machine.

ROPS, FOPS - Roll Over Protective Structure, per SAE J1040 and ISO 3471, and Falling Object Protective Structure per ISO 3449, Level I. Level II is available. Extra insulated cab is available as an option (Reduced noise level).

XI

T180 Service Manual

SAFETY & MAINTENANCE

SAFETY & MAINTENANCE AIR CLEANER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 Replacing Filter Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 BOB-TACH (HAND LEVER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 BOB-TACH (POWER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-131-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 10-131-1 ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing And Replacing Coolant . . . . . . . . . . . . . . . . . . . . . . .

10-90-1 10-90-2 10-90-1 10-90-2

ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . .

Checking And Adding Engine Oil. . . . . . . . . . . . . . . . . . . . . . .

Engine Oil Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing And Replacing Oil And Filter. . . . . . . . . . . . . . . . . .

10-110-1 10-110-1 10-110-1 10-110-1

FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Biodiesel Blend Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Filling The Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing Air From The Fuel System . . . . . . . . . . . . . . . . . . .

10-100-1 10-100-1 10-100-2 10-100-3 10-100-1 10-100-3

HYDRAULIC/HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . .

Breather Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic / Hydrostatic Fluid Chart . . . . . . . . . . . . . . . . . . . . .

Removing And Replacing Case Drain Filters. . . . . . . . . . . . . .

Removing And Replacing Hydraulic Charge Filter. . . . . . . . . .

Removing And Replacing Hydraulic Fluid . . . . . . . . . . . . . . . .

Removing And Replacing Hydraulic / Hydrostatic Filter . . . . .

10-120-1 10-120-5 10-120-1 10-120-1 10-120-4 10-120-5 10-120-2 10-120-3

LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Installing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Removing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-2 LIFTING AND BLOCKING THE LOADER . . . . . . . . . . . . . . . . . . . 10-10-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10-1 LOADER STORAGE AND RETURN TO SERVICE . . . . . . . 10-170-1 Return To Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1 Continued On Next Page 10-01

T180 Service Manual

SAFETY & MAINTENANCE (CONT’D) LUBRICATING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 Lubrication Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cab Door Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lowering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Raising . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Applications Kit . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Applications Kit Inspection And Maintenance . . . .

10-30-1 10-30-4 10-30-1 10-30-3 10-30-2 10-30-4 10-30-4

PIVOT PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . 10-160-1 REMOTE START TOOL KIT-MEL1563. . . . . . . . . . . . . . . . . .

Remote Start Procedure . . . . . . . . . . . . . . . . . . . . . . . . . .

Remote Start Tool - MEL1563 . . . . . . . . . . . . . . . . . . . . . .

Service Tool Harness Communicator - MEL1566 . . . . . . .

Service Tool Harness Control - MEL1565 . . . . . . . . . . . . .

10-60-1 10-60-4 10-60-1 10-60-3 10-60-2

REMOTE START TOOL (SERVICE TOOL) KIT - 6689779 . .

Computer Service Tool Harness - 6689746 . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loader Service Tool Harness - 6689747 . . . . . . . . . . . . . .

Remote Start Procedure . . . . . . . . . . . . . . . . . . . . . . . . . .

Remote Start Tool (Service Tool) - 6689778 . . . . . . . . . . .

10-61-1 10-61-4 10-61-1 10-61-3 10-61-5 10-61-2

SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 SPARK ARRESTOR MUFFLER . . . . . . . . . . . . . . . . . . . . . . 10-150-1 Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1 STOPPING THE ENGINE AND LEAVING THE LOADER . . 10-180-1 Emergency Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1 TOWING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 TRANSPORTING THE LOADER ON A TRAILER . . . . . . . . . 10-40-1 Fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1 Loading And Unloading . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1 TIGHTEN ALL HARDWARE PER SIZE TO GRADE 5 TORQUE (SEE STANDARD TORQUE SPECIFICATIONS FOR BOLTS, SECTION SPEC-01) UNLESS OTHERWISE SPECIFIED.

10-02

T180 Service Manual

LIFTING AND BLOCKING THE LOADER

Figure 10-10-2

Procedure

WARNING AVOID INJURY OR DEATH Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service.

Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0807

P-31849A

Always park the loader on a level surface.

Put floor jack under the rear of the loader [Figure 10-102].

Figure 10-10-1

Lift the rear of the loader and install jackstands [Figure 10-10-2].

Figure 10-10-3

B-7023A

WARNING

P-24646

Put jackstands under the front axles and rear corners of the frame before running the engine for service.

Failure to use jackstands can allow the machine to fall or move and cause injury or death.

W-2017-0286

Put the floor jack under the front of the loader [Figure 1010-3].

Lift the front of the loader and put jackstands under the axle tubes [Figure 10-10-3].

NOTE: Make sure the jackstands do not touch the tracks. Make sure tracks clear the floor or any obstacles.

10-10-1

T180 Service Manual

Figure 10-20-2

LIFT ARM SUPPORT DEVICE Installing

1

WARNING Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death.

Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death.

W-2572-0407

P-45252

Lower the lift arm support device to the top of the lift cylinder. Hook the free end of the spring (Item 1) [Figure 10-20-2] to the lift arm support device so there will be no interference with the support device engagement.

Sit in the operator’s seat, fasten the seat belt and lower the seat bar. Start the engine.

Figure 10-20-3

Remove attachment from the loader. (See BOB-TACH (HAND LEVER) on Page 50-40-1.) OR (See BOB-TACH (POWER) on Page 50-41-1.)

2

1 Figure 10-20-1 2 P-54470A

N-20524B

Raise the lift arms until the lift arm support device drops onto the lift cylinder rod (Item 1) [Figure 10-20-3]

3

Lower the lift arms slowly until the support device is held between the lift arm and the lift cylinder. Stop the engine.

Raise the seat bar and move both pedals until both pedals lock.

1

Install pin (Item 2) [Figure 10-20-3] into the rear of the lift arm support device below the cylinder rod.

P-45251

Put jackstands under the rear corners of the loader frame (Inset) [Figure 10-20-1].

Disconnect the spring (Item 1) from the lift arm support device retaining pin. Support the lift arm support device (Item 2) with your hand and remove the retaining pin (Item 3) [Figure 10-20-1].

10-20-1

T180 Service Manual

Figure 10-20-5

LIFT ARM SUPPORT DEVICE (CONT’D) Removing Remove the pin from the lift arm support device.

1

Figure 10-20-4

1

P-45251

Raise the lift arms a small amount. The spring will lift the support device off the lift cylinder rod. Lower the lift arms.

Stop the engine.

P-45486

Connect the spring (Item 1) [Figure 10-20-4] from the lift arm support device to the bracket below the lift arms.

Sit in the operator’s seat fasten the seat belt and lower the seat bar.

Start the engine.

Raise the seat bar, disconnect the seat belt, move pedals until both pedals lock and exit the cab.

Disconnect the spring from the bracket.

Raise the support device into storage position and insert pin (Item 1) [Figure 10-20-5] through lift arm support device and bracket. Connect the spring to the pin.

Remove the jackstands.

10-20-2

T180 Service Manual

OPERATOR CAB Description The Bobcat Loader has an operator cab (ROPS and FOPS) as standard equipment to protect the operator from rollover and falling objects. Check with your dealer if the operator cab has been damaged. The seat belt must be worn for rollover protection.

ROPS / FOPS - Roll Over protective Structure per ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level I. Level II is available.

Level I Protection from falling bricks, small concrete blocks, and hand tools encountered in operations such as highway maintenance, landscaping, and other construction sites.

Level II Protection from falling trees, rocks: for machines involved in site clearing, overhead demolition or forestry.

WARNING Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Bobcat Company. Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death.

W-2069-0200

10-30-1

T180 Service Manual

OPERATOR CAB (CONT’D) Raising Always stop the engine before raising or lowering the cab.

Stop the loader on a level surface. Lower the lift arms. If the lift arms must be up while raising the operator cab, install the lift arm support device. (See LIFT ARM SUPPORT DEVICE on Page 10-20-1.)

Figure 10-30-1

NOTE: On Advanced Control System (ACS) equipped machines, the steering levers could contact the cab frame while raising or lowering the operator cab. The engine MUST be stopped before raising or lowering the cab.

Figure 10-30-3

P-43747

Install jackstands under the rear of the loader frame [Figure 10-30-1].

Figure 10-30-2

P-45261

Lift on the grab handles and bottom of the operator cab [Figure 10-30-3] slowly until the cab is all the way up and the latching mechanism engages.

P-31288

P-31289

Remove the nuts and plates [Figure 10-30-2] (both sides) at the front corners of the cab.

10-30-2

T180 Service Manual

OPERATOR CAB (CONT’D) Lowering Always stop the engine before raising or lowering the cab.

Support the cab and release the latching mechanism (Inset) [Figure 10-30-4]. Remove your hand from latching mechanism when the cab is past the latch stop.

Use both hands to lower the cab all the way.

NOTE: Always use the grab handles to lower the cab.

WARNING

Figure 10-30-4

PINCH POINT CAN CAUSE INJURY Remove your hand from the latching mechanism when the cab is past the latch stop.

W-2469-0803

Figure 10-30-5

N-20120

P-45262

Pull down on the bottom of the operator cab until it stops at the latching mechanism [Figure 10-30-4].

NOTE: The weight of the cab increases when equipped with options and accessories such cab door, heater, air conditioning, etc. In these cases, the cab may need to be raised slightly from the latch to be able to release the latch.

P-31288

P-31289

Install the plates and nuts (both sides) [Figure 10-30-5].

Tighten the nuts to 40-45 ft.-lb. (54-61 N•m) torque.

NOTE: On Advanced Control System (ACS) equipped machines, the steering levers could contact the cab frame while raising or lowering the operator cab. The engine MUST be stopped before raising or lowering the cab.

10-30-3

T180 Service Manual

Special Applications Kit

OPERATOR CAB (CONT’D) Cab Door Sensor This machine may be equipped with a Cab Door Sensor.

WARNING

Figure 10-30-6

AVOID INJURY OR DEATH Some attachment applications can cause flying debris or objects to enter front, top or rear cab openings. Install the Special Applications Kit to provide added operator protection in these applications.

3

S3999A

W-2737-0508

Figure 10-30-8 1 2 P-68116 P-68115

The cab door (option) has a sensor (Item 1) [Figure 1030-6] installed which deactivates the lift and tilt valves when the door is open.

A decal is located on the latch mechanism (Item 2) [Figure 10-30-6].

B-25286A

The LIFT & TILT VALVE light (Item 3) [Figure 10-30-6] will be OFF when the door is closed, the key switch is turned to RUN or the RUN / ENTER button is pressed, the seat bar is lowered and the PRESS TO OPERATE LOADER button is pressed.

Available for special applications to restrict material from entering cab openings. Kit includes 1/2 inch Lexan® front door, top and rear windows [Figure 10-30-8].

See your Bobcat dealer for availability.

Figure 10-30-7

Special Applications Kit Inspection And Maintenance • • •

• • •

Inspect for cracks or damage. Replace if required.

Pre-rinse with water to remove gritty materials.

Wash with a mild household detergent and warm water.

Use a sponge or soft cloth. Rinse well with water and dry with a clean soft cloth or rubber squeegee.

Do not use abrasive or highly alkaline cleaners.

Do not operate windshield wipers on a dry surface.

Do not clean with metal blades or scrapers.

10-30-4

T180 Service Manual

•

The LIFT & TILT VALVE light (Item 3) [Figure 10-30-6] will be ON when the door is open, the key switch is turned to RUN or the RUN / ENTER button is pressed, the seat bar is lowered and the PRESS TO OPERATE LOADER button is pressed.

[DOOR] will appear in the data display [Figure 10-30-7].

TRANSPORTING THE LOADER ON A TRAILER

Fastening

Loading And Unloading

Figure 10-40-2

WARNING AVOID SERIOUS INJURY OR DEATH Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle. Wood ramps can break and cause personal injury.

P-73277

N-19048A

W-2058-0807

Be sure the transport and towing vehicles are of adequate size and capacity for weight of loader.. (See Performance on Page SPEC-10-2) Figure 10-40-1

Alternate Front Tie Down

P-45989

P-24512B

P-45216A

A loader with an empty bucket or no attachment must be loaded backward onto the transport vehicle [Figure 1040-1].

P-45217A

Use the following procedure to fasten the Bobcat Loader to the transport vehicle to prevent the loader from moving during sudden stops or when going up or down slopes [Figure 10-40-2].

•

Lower the bucket or attachment to the floor.

•

Stop the engine.

•

Engage the parking brake.

•

Install chains at the front and rear loader tie down positions [Figure 10-40-2].

•

Fasten each end of the chain to the transport vehicle.

10-40-1

T180 Service Manual

The rear of the trailer must be blocked or supported (Inset) [Figure 10-40-1] when loading or unloading the loader to prevent the front end of the trailer from raising up.

TOWING THE LOADER Procedure Because of the design of the loader, there is not a recommended towing procedure. •

The loader can be lifted onto a transport vehicle.

•

The loader can be skidded a short distance to move for service (EXAMPLE: Move onto a transport vehicle.) without damage to the hydrostatic system.

(The tracks will not turn.) There might be slight wear to the tracks when the loader is skidded.

The towing chain (or cable) must be rated at one and one-half times the weight of the loader. (See Performance on Page SPEC-10-2).

10-50-1

T180 Service Manual

Figure 10-60-2

REMOTE START TOOL KIT-MEL1563 Remote Start Tool - MEL1563 Tools that will be needed to complete the following steps are:

2 MEL1563 - Remote Start Tool MEL1565 - Service Tool Harness Control MEL1566 - Service Tool Harness Communicator (Computer Interface)

3

1

Figure 10-60-1

P16117

1

The traction lock switch (Item 1) [Figure 10-60-2] is used to turn traction lock ON or OFF. Push the switch to the override postion. The switch will illuminate to indicate traction lock OVERRIDE, in this position the wheels are able to turn.

P16114

The remote start tool (Item 1) [Figure 10-60-1] is required when the service technician is checking the hydraulic/hydrostatic system or adjusting the steering linkage.

The maximum flow/variable flow switch (Item 2) [Figure 10-60-2] is used to activate the auxiliary hydraulics.

Pressing the switch once will activate maximum flow.

Pressing the switch again will activate variable flow. The switch will illuminate to indicate which flow rate is active.

Pressing the switch a third time will turn the flow OFF. The switch is used when checking pressures and flow rate.

The auxiliary pressure release (Item 3) [Figure 10-60-2] is used to release hydraulic pressure to the front and/or rear auxiliary couplers. To release pressure; push and hold the switch for a few seconds.

NOTE: With the engine running; pushing and holding the pressure release switch will cause the engine to stop. To relieve the pressure; press the switch until the engine stops.

10-60-1

T180 Service Manual

REMOTE START TOOL-MEL1563 (CONT'D)

Service Tool Harness Control - MEL1565

Remote Start Tool - MEL1563 (Cont’d)

Figure 10-60-5

Figure 10-60-3

2

1

1

P16114 P16116

The service tool harness control (Item 1) [Figure 10-605] is used to connect the remote start tool (Item 2) [Figure 10-60-5] to the electrical system on the loader.

Figure 10-60-4

Figure 10-60-6

1

1

P16120

The 10-pin rectangular connector (Item 1) [Figure 10-603] is used to update software in the Deluxe Instrumentation Panel (Item 1) [Figure 10-60-4].

NOTE: The Service PC must be connected to the remote start tool to update the deluxe panel software.

N-19561

Remove the plug (Item 1) [Figure 10-60-6] from the loader harness connector.

Connect the service tool harness control to the loader harness connector.

The panel must be removed from inside the operator cab and plugged into this connector [Figure 10-60-3].

10-60-2

T180 Service Manual

REMOTE START TOOL-MEL1563 (CONT'D)

Service Tool Harness Communicator - MEL1566

Service Tool Harness Control - MEL1565 (Cont’d)

Figure 10-60-8

Figure 10-60-7

2

2 1

1 P16119 N-19631

Loaders equipped with an attachment harness (Item 1) [Figure 10-60-7] must disconnect the attachment harness from the loader harness (Item 2) [Figure 10-607].

The service tool harness communicator (Item 1) [Figure 10-60-8] is required to connect remote start tool to the Service PC (Item 2) [Figure 10-60-8].

Connect the service tool harness to the ACD connector and the loader harness connector.

NOTE: To monitor, diagnose or load new software the Service PC must be connected to the Remote Start Tool Switch.

10-60-3

T180 Service Manual

Figure 10-60-11

REMOTE START TOOL KIT-MEL1563 (CONT’D) Remote Start Procedure The tool listed will be needed to do the following procedure: MEL1563: Remote Start Tool Kit

1

Figure 10-60-9

1 N-19150

Remove the plug (Item 1) [Figure 10-60-10] or disconnect the attachment control harness (Item 1) [Figure 10-60-11] if connected.

Figure 10-60-12

P16115

The remote start tool (Item 1) [Figure 10-60-9] is required when the operator cab is in the raised position for service and the service technician needs to turn the key switch on or start the engine. Example: adjusting the steering linkage.

Lift and block the loader.

Raise the lift arms (if required by the procedure) and install an approved lift arm support device.

P13861

Raise the operator cab (if required by the procedure).

Open the rear door of the loader.

Connect the remote start tool to the engine harness connector [Figure 10-60-12].

Figure 10-60-10

NOTE: The key switch on the right-hand side operator panel must be in the off position or the Remote Start Kit will not operate.

WARNING 1

N-19151

AVOID INJURY OR DEATH With the 7-pin connector plugged into the loader and Remote Start Key Switch in the OFF position, the loader can still be started from the operator panel inside the cab. Placing the key switch of the remote start tool in the run position disconnects the operator panel key switch from the start circuit. If the service technician will be working the engine area it is important to remove the operator panel keys.

W-2357-0899

10-60-4

T180 Service Manual

Figure 10-60-14

REMOTE START TOOL KIT-MEL1563 (CONT'D) Remote Start Procedure (Cont'd) Figure 10-60-13

2 3

1

1

P16118

P16116

The remote start tool (Item 1) [Figure 10-60-13] has three rocker switches.

The traction lock switch (Item 1) [Figure 10-60-14] is used to turn traction lock on or off. Push the switch to the override position. The switch will illuminate to indicate traction lock OVERRIDE, in this position the wheels are able to turn.

The maximum flow/variable flow switch (Item 2) [Figure 10-60-14] is used to activate the auxiliary hydraulics.

Pressing the switch once will activate variable flow.

Pressing the switch again will activate maximum flow.

The switch will illuminate to indicate which flow rate is active. Pressing the switch a third time will turn the flow OFF. The switch is used when checking pressures and flow rate.

The auxiliary pressure release (Item 3) [Figure 10-60-14] is used to release hydraulic pressure to the front and/or rear auxiliary couplers. To release pressure; push and hold the switch for three seconds.

NOTE: With the engine running; pushing and holding the pressure release switch will cause the engine to stop in three seconds. To relieve the pressure; continue to press the switch after the engine has stopped.

10-60-5

T180 Service Manual

REMOTE START TOOL KIT-MEL1563 (CONT'D) Remote Start Procedure (Cont'd) NOTE: With the engine running; pushing and holding the pressure release switch will cause the engine to stop in three seconds. To relieve the pressure at the rear or right hand auxiliary, (If so equipped.) continue to hold the switch for three seconds after the engine has stopped.

Figure 10-60-15

P-34661

Push the couplers on the front auxiliary block toward the block and hold for five seconds to release the front auxiliary pressure [Figure 10-60-15].

10-60-6

T180 Service Manual

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 Description The Remote Start Tool (Service Tool) Kit is a replacement tool for MEL 1563 Remote Start Tool and MEL 1400B BOSS® Diagnostic Tool.

The Remote Start Tool (Service Tool) Kit, P/N 6689779, can be used to service older loaders with the BOSS® system using the supplied BOSS® Service Tool Harness P/N 6689745.

The Remote Start Tool (Service Tool) Kit, P/N 6689779, can be used to service newer loaders using the supplied harness P/N 6689747.

A computer can be connected to the Remote Start Tool (Service Tool) for diagnostics and software updates using the computer harness P/N 6689746 in conjunction with the loader harness.

10-61-1

T180 Service Manual

Figure 10-61-17

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D)

2

Remote Start Tool (Service Tool) - 6689778 Tools that will be needed to complete the following steps are:

5

3

Order from Bobcat Parts P/N: 6689779 - Remote Start Tool (Service Tool) Kit

6

4

Kit Includes: 6689778 - Remote Start Tool (Service Tool) 6689747 - Loader Service Tool Harness 6689746 - Computer Service Tool Harness 6689745 - BOSSÂŽ Service Tool Harness

1

P-76439

Figure 10-61-16 The Remote Start Tool (Service Tool) (Item 1) [Figure 1061-17] has five buttons.

The STOP button (Item 2) [Figure 10-61-17] is used to stop the Remote Start Tool (Service Tool) from communicating and stop the loader engine.

The RUN button (Item 3) [Figure 10-61-17] is used to turn the Remote Start Tool (Service Tool) on and activates the loader ignition power. The button will illuminate to indicate the service tool is active.

1

The START button (Item 4) [Figure 10-61-17] is used to start the loader engine.

P-76678

The remote start tool (Item 1) [Figure 10-61-16] is required when the service technician is checking the hydraulic / hydrostatic system or adjusting the steering linkage.

The traction lock button (Item 5) [Figure 10-61-17] is used to turn traction lock ON or OFF. Push the button and the button will illuminate indicating the traction lock is disabled in which the wheels or tracks are able to turn.

The auxiliary button (Item 6) [Figure 10-61-17] is used to activate the auxiliary hydraulics. The button will illuminate to indicate the auxiliary hydraulics are active. Pressing the button a second time will turn the flow OFF. The button is used when checking pressures and flow rate.

10-61-2

T180 Service Manual

Figure 10-61-20

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D) Loader Service Tool Harness - 6689747

2

Figure 10-61-18

1 1

P-76452

2

Loaders with an attachment control harness (7 pin or 14 pin), the attachment harness (Item 1) must be disconnected from the loader harness (Item 2) [Figure 10-61-20].

P-76678

The loader service tool harness (Item 1) [Figure 10-6118] is used to connect the remote start tool (service tool) (Item 2) [Figure 10-61-18] to the electrical system on the loader.

When the remote start procedure is completed, replace the loader connector cap (Item 1) [Figure 10-61-19] or reconnect the attachment control harness to the loader harness [Figure 10-61-20].

Figure 10-61-19

1

P-76451

Loaders without an attachment control harness, remove the loader harness cap (Item 1) [Figure 10-61-19] and connect the Loader Service Tool Harness from the Remote Start Tool (Service Tool).

10-61-3

T180 Service Manual

Computer Service Tool Harness - 6689746

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D)

Figure 10-61-22

Loader Service Tool Harness - 6689747 (Cont’d) Figure 10-61-21 2

1 1

2

3

P-76450

1 P-76453

NOTE: The Remote Start Tool (Service Tool) connection harness has two connectors (Item 1) and (Item 3). The main connector (Item 1) [Figure 10-61-21] is always used for connection to the loader harness.

The computer service tool harness (Item 1) [Figure 1061-22] is required to connect remote start tool (service tool) to the Service PC (Item 2) [Figure 10-61-22].

The second connector (Item 3) [Figure 10-6121] is used for attachment ACD upgrades or attachment operational diagnostics only. This connector has a cap attached to it to prevent damage or corrosion when not in use.

Connect the Remote Start Tool (Service Tool) connector (Item 1) to the loader harness connector (Item 2) and the other Remote Start Tool (Service Tool) connector to the ACD harness connector (Item 3) [Figure 10-61-21].

NOTE: The right instrument panel (Deluxe Instrumentation Panel or Standard Key Panel) must be in the off position or the Remote Start Tool (Service Tool) will not operate.

P-76454

10-61-4

T180 Service Manual

Figure 10-61-24

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D) Remote Start Procedure

1

WARNING AVOID INJURY OR DEATH With the 7-pin connector plugged into the loader and Remote Start Tool RUN button is not illuminated, the loader can still be started from the operator panel inside the cab.

P-76451

Pressing the RUN button on the Remote Start Tool disconnects the operator panel from the start circuit.

If the service technician will be working in the engine area it is important to remove the operator panel key or lock the keypad with a unique password.

W-2647-0707

The tool listed will be needed to do the following procedure:

Loaders without an attachment control harness, remove the loader harness cap (Item 1) [Figure 10-61-24] and connect the Loader Service Tool Harness from the Remote Start Tool (Service Tool).

Figure 10-61-25 2

6689779: Remote Start Tool (Service Tool) Kit Figure 10-61-23

1

1

P-76452

Loaders with an attachment control harness (7 pin or 14 pin), the attachment harness (Item 1) must be disconnected from the loader harness (Item 2) [Figure 10-61-25].

P-76450

The Remote Start Tool (Service Tool) (Item 1) [Figure 1061-23] is required when the operator cab is in the raised position for service and the service technician needs to turn on the loader or start the engine. Example: adjusting the steering linkage.

When the remote start procedure is completed, replace the loader connector cap (Item 1) [Figure 10-61-25] or reconnect the attachment control harness to the loader harness [Figure 10-61-25].

Lift and block the loader.

Raise the lift arms (if required by the procedure) and install an approved lift arm support device.

Raise the operator cab (if required by the procedure).

Open the rear door of the loader.

10-61-5

T180 Service Manual

Figure 10-61-27

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D)

2

Remote Start Procedure (Cont'd) Figure 10-61-26

5

3

6

4

2 1 1

P-76439

3 1

The Remote Start Tool (Service Tool) (Item 1) [Figure 1061-27] has five buttons.

P-76453

NOTE: The Remote Start Tool (Service Tool) connection harness has two connectors (Item 1) and (Item 3). The main connector (Item 1) [Figure 10-61-26] is always used for connection to the loader harness.

The second connector (Item 3) [Figure 10-6126] is used for attachment ACD upgrades or attachment operational diagnostics only. This connector has a cap attached to it to prevent damage or corrosion when not in use.

Connect the Remote Start Tool (Service Tool) connector (Item 1) to the loader harness connector (Item 2) and the other Remote Start Tool (Service Tool) connector to the ACD harness connector (Item 3) [Figure 10-61-26].

NOTE: The right instrument panel (Deluxe Instrumentation Panel or Standard Key Panel) must be in the off position or the Remote Start Tool (Service Tool) will not operate.

The STOP button (Item 2) [Figure 10-61-27] is used to stop the Remote Start Tool (Service Tool) from communicating and stop the loader engine.

The RUN button (Item 3) [Figure 10-61-27] is used to turn the Remote Start Tool (Service Tool) on and activates the loader ignition power. The button will illuminate to indicate the service tool is active.

The START button (Item 4) [Figure 10-61-27] is used to start the loader engine.

The traction lock button (Item 5) [Figure 10-61-27] is used to turn traction lock ON or OFF. Push the button and the button will illuminate indicating the traction lock is disabled in which the wheels or tracks are able to turn.

The auxiliary button (Item 6) [Figure 10-61-27] is used to activate the auxiliary hydraulics. The button will illuminate to indicate the auxiliary hydraulics are active. Pressing the button a second time will turn the flow OFF. The button is used when checking pressures and flow rate.

P-76454

10-61-6

T180 Service Manual

Figure 10-61-29

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D) Remote Start Procedure (Cont'd) Figure 10-61-28

1

2 P-34661

Push the couplers on the front auxiliary block toward the block and hold for five seconds to release the front auxiliary pressure [Figure 10-61-29].

P-76441

The gear icon with the left facing arrows (Item 1) [Figure 10-61-28] will illuminate and blink when the RUN key is pressed and the loader is communicating with the service tool.

The computer icon with the right facing arrows (Item 2) [Figure 10-61-28] will illuminate and blink when the Remote Start Tool (Service Tool) is transmitting data to and from the computer.

NOTE: To relieve the pressure at the rear or secondary front auxiliary, (if equipped) press the RUN button on the remote start tool. Then press the auxiliary (AUX) hydraulics button on the remote start tool and move the AUXILIARY Hydraulic Switch on the to the right and left several times.

10-61-7

T180 Service Manual

SERVICE SCHEDULE Chart Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Bobcat loader.

WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0903

SERVICE SCHEDULE ITEM Engine Oil Engine Air Filter and Air System Engine Cooling System

SERVICE REQUIRED

✶ ❍

8-10

50

100

■

■

■

250

500

1000

Check the oil level and add as needed. Do not overfill.

Check display panel. Service only when required. Check for leaks and damaged components.

Clean debris from oil cooler, radiator and grill. Check coolant level COLD and add premixed coolant as needed.

Remove the trapped water.

Lubricate with multi-purpose lithium based grease.

Fuel Filter Lift Arms, Cylinders, Bob-Tach Pivot Pins and Wedges Seat Bar, Control Interlocks, Seat Check the condition of seat belt. Clean or replace seat belt retractors as Belt, Seat Belt Retractors needed. Check the seat bar and control interlocks for correct operation. Clean dirt and debris from moving parts.

Bobcat Interlock Control Systems Check for correct function. Lift and Tilt functions MUST NOT operate with seat (BICS) bar raised. See details in this Manual.

Safety Signs and Safety Treads Check for damaged signs (decals) and safety treads. Replace any signs or safety treads that are damaged or worn.

Operator Cab Check the fastening bolts, washers and nuts. Check the condition of the cab.

Indicators and Lights Check for correct operation of all indicators and lights.

Heater and A/C Filters Clean or replace filters as needed.

(If Equipped) Hydraulic Fluid, Hoses and Check fluid level and add as needed. Check for damage and leaks. Repair or Tubelines replace as needed.

Tracks Check for damaged or worn tracks and correct tension.

Track Sprocket Nuts Check torque. Tighten as needed. See procedure in this manual.

Parking Brake, Foot Pedals, Check for correct operation. Repair or adjust as needed.

Hand Controls and Steering Levers or Joysticks Spark Arrestor Muffler Clean the spark chamber.

Battery Check cables, connections and electrolyte level. Add distilled water as needed.

Steering Lever Pivots Grease fittings.

Fuel Filter Replace filter element.

Engine / Hydro. Drive Belt Check for wear or damage. Check idler arm stop.

Drive Belts (Alternator, air Check condition and tension. Adjust or replace as needed. conditioning, water pump) Bobcat Interlock Control System Check the function of the lift arm bypass control.

(BICS) Engine Oil and Filter Replace oil and filter.

Hydraulic / Hydrostatic Filter, Replace the hydraulic / hydrostatic filter, charge filter, and the reservoir Charge Filter, Reservoir Breather breather.

Hydrostatic Motor Carrier Replace oil with high performance synthetic oil P/N 6682546.

Hydraulic Reservoir Replace the fluid.

Case Drain Filters Replace the filters.

Engine Valves Adjust the engine valves.

Coolant Replace the coolant

■ ▲ ❏ ●

HOURS

❏

▲

▲

✶

●

▲ ❍ Every 2 years

Or every 12 months.

Perform at first 50 hours, then as scheduled.

Check every 8 - 10 hours for the first 24 hours, then at 50 hour intervals.

Replace the hydraulic / hydrostatic filter element after the first 50 hours, then when service code [M0217] is displayed or as scheduled.

Change oil and filter every 100 hours when operating under severe conditions.

Perform at first 500 hours, then as scheduled.

10-70-1

T180 Service Manual

AIR CLEANER SERVICE

Outer Filter

Replacing Filter Elements

Figure 10-80-3

Figure 10-80-1 2

2

1

3 1

P-76460G P-76883

Figure 10-80-2 Open the latches (Item 1) and remove the dust cover (Item 2) [Figure 10-80-3].

Figure 10-80-4

1

B-15553M

1

It is important to change the air filter element only when necessary. The Service indicator (Item 1) will FLASH and service code [M0117] (Air Filter Plugged) will show in the Data Display (Item 2) when the Information button (Item 3) [Figure 10-80-1] is held for two seconds.

The Air Cleaner icon on the Deluxe Instrumentation Panel, if equipped, will be ON (Item 1) [Figure 10-80-2].

Replace the inner filter every third time the outer filter is replaced or as indicated.

P-76884

Pull the outer filter element (Item 1) [Figure 10-80-4] out and discard.

NOTE: Make sure all sealing surfaces are free of dirt and debris.

Install new filter element. Push all the way in until it contacts the base of the housing.

Outer Filter Install the dust cover and secure the latches [Figure 1080-3].

10-80-1

T180 Service Manual

Figure 10-80-6

AIR CLEANER (CONT’D) Replacing Filter Elements (Cont’d) Inner Filter

2

Only replace the inner filter element under the following conditions: • •

1

Replace the inner filter element every third time the outer filter is replaced.

After the outer element has been replaced, start the engine and run at full RPM. If the HOURMETER / CODE DISPLAY shows [M0117] (Air Filter Plugged), replace the inner filter element.

P-76883

Figure 10-80-5

Install the dust cover (Item 2) and secure the latches (Item 1) [Figure 10-80-6].

1

P-76885

Remove the inner filter element (Item 1) [Figure 10-805].

NOTE: Make sure all sealing surfaces are free of dirt and debris.

Install new filter element. Push all the way in until it contacts the base of the housing.

Install the outer element [Figure 10-80-4].

10-80-2

T180 Service Manual

Figure 10-90-2

ENGINE COOLING SYSTEM Check the cooling system every day to prevent overheating, loss of performance or engine damage.

1

WARNING AVOID INJURY OR DEATH Wear safety glasses to prevent eye injury when any of the following conditions exist: • When fluids are under pressure.

• Flying debris or loose material is present.

• Engine is running.

• Tools are being used.

2

P-76189

W-2019-0907

Cleaning Open the rear door. (See REAR DOOR on Page 50-701.)

Remove the rear grill. (See REAR GRILL on Page 50-601.)

NOTE: Be careful when raising and lowering the air conditioning condenser so that the air conditioning condenser does not fall on the oil cooler and damage the fins.

Raise the air conditioning condenser (Item 1) and use low air pressure or water pressure to clean the top of the oil cooler (Item 2) [Figure 10-90-2].

Figure 10-90-3

Figure 10-90-1

2

1

1 P-76190 P-76181

Use low air pressure or water pressure to clean the top of the air conditioning condenser (Item 1) [Figure 10-90-1], if equipped.

NOTE: Be careful when raising and lowering the oil cooler so that the oil cooler does not fall on the radiator and damage the fins.

Raise the oil cooler (Item 1) and use low air pressure or water pressure to clean the top of the radiator (Item 2) [Figure 10-90-3].

Lower the oil cooler.

Lower the air conditioning condenser, if equipped.

Check the cooling system for leaks.

Install the rear grill and close the rear door.

10-90-1

T180 Service Manual

ENGINE COOLING SYSTEM (CONT’D)

Removing And Replacing Coolant

Checking Level

Open the rear door and remove the rear grill.

Open the rear door and raise the rear grill..

Figure 10-90-5

Check coolant level using the level markers (Item 3) [Figure 10-90-5] on the tank. Coolant must be at the bottom marker when the engine is cold; top marker when hot.

1

Close the rear door before operating the loader.

2

IMPORTANT

3

AVOID ENGINE DAMAGE Always use the correct ratio of water to antifreeze.

P-76892

Too much antifreeze reduces cooling system efficiency and may cause serious premature engine damage.

Too little antifreeze reduces the additives which protect the internal engine components; reduces the boiling point and freeze protection of the system.

Always add a premixed solution. Adding full strength concentrated coolant can cause serious premature engine damage.

I-2124-0497

Figure 10-90-4

P-76972

Remove the coolant fill cap (Item 1) [Figure 10-90-5].

Connect a hose to the engine block drain (Item 2) [Figure 10-90-5]. Drain the coolant into a container.

Recycle or dispose of coolant in an environmentally safe manner.

Mix new coolant in a separate container. (See Capacities on Page SPEC-10-4) NOTE: The loader is factory filled with propylene glycol coolant (purple color). DO NOT mix propylene glycol with ethylene glycol.

Add premixed coolant, 47% water and 53% propylene glycol to the recovery tank. See checking level at left.

One gallon and one pint (4,3 L) of propylene glycol mixed with one gallon (3,8 L) of water is the correct mixture of coolant to provide a -34°F (-37°C) freeze protection.

1

Fill the tank until it is at the lower marker on the tank.

Use a refractometer to check the condition of propylene glycol in your cooling system and replace the coolant fill cap.

NOTE: When installing the coolant fill cap, the cap must be tightened until it clicks.

P-76786

NOTE: All access covers (Item 1) [Figure 10-90-4] (both sides) must be in place to ensure correct air flow through the oil cooler which will ensure cooling for engine and hydraulic system.

Run the engine until it is at operating temperature. Stop the engine. Check the coolant level when cool. Add coolant as needed.

Install the rear grill and close the rear door.

10-90-2

T180 Service Manual

FUEL SYSTEM

Biodiesel Blend Fuel

Fuel Specifications

Biodiesel blend fuel has unique qualities that should be considered before using in this machine:

Use only clean, high quality diesel fuel, Grade No. 2 or Grade No. 1.

•

Cold weather conditions can lead to plugged fuel system components and hard starting.

The following is one suggested blending guideline which should prevent fuel gelling during cold temperatures:

•

Biodiesel blend fuel is an excellent medium for microbial growth and contamination which can cause corrosion and plugging of fuel system components.

•

Use of biodiesel blend fuel may result in premature failure of fuel system components, such as plugged fuel filters and deteriorated fuel lines.

•

Shorter maintenance intervals may be required, such as cleaning the fuel system and replacing fuel filters and fuel lines.

•

Using biodiesel blended fuels containing more than five percent biodiesel can affect engine life and cause deterioration of hoses, tubelines, injectors, injector pump and seals.

TEMPERATURE F (C)

NO. 2

NO. 1

+15° (9°)

100%

0%

Down to -20° (-29°)

50%

50%

Below -20° (-29°)

0%

100%

At a minimum, Low Sulfur (500 ppm sulfur) Diesel Fuel must be used in this machine: The following fuels may also be used in this machine: •

Ultra Low Sulfur (15 ppm sulfur) Diesel Fuel.

•

Biodiesel Blend Fuel - Must contain no more than five percent biodiesel mixed with low sulfur or ultra low sulfur petroleum based diesel. This is commonly marketed as B5 blended diesel fuel. B5 blended diesel fuel must meet ASTM D975 (US Standard) or EN590 (EU Standard) specifications.

Apply the following guidelines if biodiesel blend fuel is used: •

Ensure the fuel tank is as full as possible at all times to prevent moisture from collecting in the fuel tank.

•

Ensure that the fuel tank cap is securely tightened.

•

Biodiesel blend fuel can damage painted surfaces, remove all spilled fuel from painted surfaces immediately.

•

Drain all water from the fuel filter daily before operating the machine.

•

Do not exceed engine oil change interval. Extended oil change intervals can cause engine damage.

•

Before vehicle storage; drain the fuel tank, refill with 100% petroleum diesel fuel, add fuel stabilizer and run the engine for at least 30 minutes.

NOTE: Biodiesel blend fuel does not have long term stability and should not be stored for more than three months.

10-100-1

T180 Service Manual

FUEL SYSTEM (CONT’D)

Figure 10-100-2 WRONG

Filling The Fuel Tank

WARNING AVOID INJURY OR DEATH Stop and cool the engine before adding fuel. NO SMOKING! Failure to obey warnings can cause an explosion or fire.

W-2063-0807

Open the rear door.

B-15650A

Figure 10-100-1

Use a clean, approved safety container to add fuel of the correct specification. Add fuel only in an area that has free movement of air and no open flames or sparks NO SMOKING . [Figure 10-100-2] Install and tighten the fuel cap (Item 1) [Figure 10-1001].

1

WARNING P-76886

Remove the fill cap (Item 1) [Figure 10-100-1].

AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire.

W-2103-0508

10-100-2

T180 Service Manual

FUEL SYSTEM (CONT’D)

Removing Air From The Fuel System

Fuel Filter

After replacing the filter element or when the fuel tank has run out of fuel, the air must be removed from the fuel system before starting the engine.

For the service interval for removing water from, or replacing the fuel filter. (See SERVICE SCHEDULE on Page 10-70-1.)

WARNING

Removing Water Figure 10-100-3

AVOID INJURY OR DEATH Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or death. Fluid leaks under pressure may not be visible.

Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury.

W-2072-0807

2

Figure 10-100-4 1 P-76887

1

Loosen the drain (Item 1) [Figure 10-100-3] at the bottom of the filter element to remove water from the filter.

2

Replacing Element Remove the filter element (Item 2) [Figure 10-100-3].

P-76888

Clean the area around the filter housing. Put clean oil on the seal of the new filter element. Install the fuel filter, and hand tighten.

Remove air from the fuel system. (See Removing Air From The Fuel System on Page 10-70-3.)

WARNING

Open the vent (Item 1) [Figure 10-100-4] on the fuel filter housing.

Squeeze the hand pump (priming bulb) (Item 2) [Figure 10-100-4] until fuel flows from the vent with no air bubbles.

Close the vent (Item 1) [Figure 10-100-4].

AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire.

W-2103-0508

10-100-3

T180 Service Manual

Run the engine until it is at operating temperature. Stop the engine.

ENGINE LUBRICATION SYSTEM Checking And Adding Engine Oil Check the engine oil level every day before starting the engine for the work shift.

Open the rear door and remove the drain hose from its storage position (Item 4) [Figure 10-110-1].

Figure 10-110-3

Figure 10-110-1 3

1 1

2

4 P-76891

Remove the drain plug (Item 1) [Figure 10-110-3] and drain the oil into a container and recycle or dispose of used oil in an environmentally safe manner.

P-76971

Park the machine on level ground. Open the rear door and remove the dipstick (Item 1) [Figure 10-110-1].

Keep the oil level between the marks on the dipstick. Do not overfill.

Engine Oil Chart

Install the oil drain cap.

Remove the oil filter (Item 2) [Figure 10-110-1] and clean the filter housing surface.

Use genuine Bobcat filter only.

Put oil on the new filter gasket, install the filter and hand tighten.

Figure 10-110-2

Remove the fill cap (Item 3) [Figure 10-110-1].

Put oil in the engine. For the correct quantity (See Capacities on Page SPEC-10-4). Do no overfill.

Start the engine and let it run for several minutes. Stop the engine and check for leaks at the filter.

Remove the dipstick (Item 1) [Figure 10-110-1] and check the oil level.

Add oil as needed if it is not at the top mark on the dipstick. Install the dipstick and close the rear door.

WARNING B-16320C

Use good quality engine oil that meets API Service Classification of CD or better [Figure 10-110-2].

AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire.

W-2103-0508

Removing And Replacing Oil And Filter For the service interval for replacing the engine oil and filter. (See SERVICE SCHEDULE on Page 10-70-1.)

10-110-1

T180 Service Manual

HYDRAULIC/HYDROSTATIC SYSTEM

Hydraulic / Hydrostatic Fluid Chart

Checking And Adding Fluid

Figure 10-120-3

Put the loader on a level surface, lower the lift arms and tilt the Bob-Tach fully back.

Stop the engine.

Figure 10-120-1

1 P-64023A

Use only recommended fluid in the hydraulic system [Figure 10-120-3]. (See Hydraulic System on Page SPEC-10-3).

P-45228C

Check the fluid level in the sight gauge (Item 1) [Figure 10-120-1].

Figure 10-120-2

1

P-48011

Open the rear door and raise the rear grill. Remove the fill cap (Item 1) [Figure 10-120-1].

Add fluid [Figure 10-120-1] as needed to bring the level to the center of the sight gauge.

Lower the rear grill and close the rear door.

10-120-1

T180 Service Manual

HYDRAULIC / HYDROSTATIC SYSTEM (CONT’D)

Lower the operator cab. (See Lowering on Page 10-303.)

Removing And Replacing Hydraulic Fluid For the correct service interval SCHEDULE on Page 10-70-1.)

(See

SERVICE

Add the correct fluid to the reservoir until the fluid level is at the center of the sight gauge. (See Checking And Adding Fluid on Page 10-120-1.)

Replace the fluid if it becomes contaminated or after major repair.

Always replace the hydraulic / hydrostatic filter, the case drain filters and the hydraulic charge filter whenever the hydraulic fluid is replaced. (See Removing And Replacing Hydraulic / Hydrostatic Filter on Page 10-1203.)

Open the rear door and raise the rear grill. Remove the fill cap.

Raise the operator cab. (See Raising on Page 10-30-2.)

Figure 10-120-4

1

P-37661

Remove the plug (Item 1) [Figure 10-120-4] and remove the fluid.

Recycle or dispose of used fluid in an environmentally safe manner.

WARNING AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire.

W-2103-0508

Install the plug (Item 1) [Figure 10-120-4].

10-120-2

T180 Service Manual

HYDRAULIC / HYDROSTATIC SYSTEM (CONT’D) Removing And Replacing Hydraulic / Hydrostatic Filter For the correct service interval SCHEDULE on Page 10-70-1.)

(See

SERVICE

Open the rear door.

Figure 10-120-5

1

P-48470

Remove the filter (Item 1) [Figure 10-120-5].

Clean the surface of the filter housing where the filter seal contacts the housing.

Put clean oil on the seal of the new filter element. Install and hand tighten the filter element.

WARNING AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire.

W-2103-0508

Close the rear door.

Start the engine and operate the loader hydraulic controls.

Stop the engine and check for leaks at the filter.

Check the fluid level in the reservoir and add as needed.

(See Checking And Adding Fluid on Page 10-120-1.)

10-120-3

T180 Service Manual

HYDRAULIC / HYDROSTATIC SYSTEM (CONT’D)

WARNING

Removing And Replacing Case Drain Filters For the correct service interval SCHEDULE on Page 10-70-1.)

(See

SERVICE AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire.

Raise the operator cab. (See Raising on Page 10-30-2.)

Figure 10-120-6

W-2103-0508

Left Side

Lower the operator cab. (See Lowering on Page 10-303.)

Start the engine and operate the loader hydraulic controls.

Stop the engine and check for leaks at the filters.

1

Check the fluid level in the reservoir and add as needed.

(See Checking And Adding Fluid on Page 10-120-1.)

P-24734

Disconnect the hoses and fittings from the hydrostatic motor case drain filter (Item 1) [Figure 10-120-6].

Remove the mounting clamp and discard the filter.

Install fittings on new filter, install new filter, install the mounting clamp, connect and tighten the hoses.

Figure 10-120-7 Right Side

1

P-24682

Disconnect the hoses and fittings from the filter (Item 1) [Figure 10-120-7]. Remove and discard the filter.

Install fittings on new filter, install new filter, connect and tighten the hoses.

10-120-4

T180 Service Manual

HYDRAULIC / HYDROSTATIC SYSTEM (CONT’D)

WARNING

Removing And Replacing Hydraulic Charge Filter The hydraulic charge filter is located under the cab. For the correct service interval. (See SERVICE SCHEDULE on Page 10-70-1.)

Raise the operator cab. (See Raising on Page 10-30-2.)

Figure 10-120-8

AVOID INJURY OR DEATH Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or death. Fluid leaks under pressure may not be visible.

Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury.

W-2072-0807

Stop the engine and check for leaks at the filter.

Check the fluid level in the reservoir and add as needed.

(See Checking And Adding Fluid on Page 10-120-1.)

1

Breather Cap See the SERVICE SCHEDULE for the correct replacement interval. (See SERVICE SCHEDULE on Page 10-70-1.)

P-64239

Raise the operator cab. (See Raising on Page 10-30-2.)

Remove the filter (Item 1) [Figure 10-120-8].

Figure 10-120-9 Clean the surface of the filter housing where the filter seal contacts the housing.

Put clean oil on the seal of the new filter.

1 Install and hand tighten the new filter.

WARNING AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire.

W-2103-0508

Lower the operator cab. (See Lowering on Page 10-303.)

Start the engine and operate the loader controls.

hydraulic

P-76673

Remove the breather cap (Item 1) [Figure 10-120-9] and discard. (Blower housing removed for clarity.)

Install new breather cap.

Lower the opertor cab. (See Lowering on Page 10-30-3.)

10-120-5

T180 Service Manual

BOB-TACH (HAND LEVER)

The spring loaded wedge (Item 1) must contact the lower edge of the hole in the attachment [Figure 10-130-2].

Inspection And Maintenance If the wedge does not contact the lower edge of the hole [Figure 10-130-2], the attachment will be loose and can come off the Bob-Tach.

Figure 10-130-1

Figure 10-130-3

P-31693

Move the Bob-Tach levers to engage the wedges [Figure 10-130-1].

The levers and wedges must move freely.

WARNING Bob-Tach wedges must extend through the holes in attachment. Lever(s) must be fully down and locked.

Failure to secure wedges can allow attachment to come off and cause injury or death.

W-2102-0497

Figure 10-130-2 1 B-17460

2

Wedge must contact lower edge of hole in the attachment.

P-31233

Inspect the mounting frame on the attachment and BobTach, linkages and wedges for excessive wear or damage [Figure 10-130-3]. Replace any parts that are damaged, bent or missing. Keep all fasteners tight.

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts.

B-15177

The wedges (Item 1) [Figure 10-130-2] must extend through the holes in the attachment mounting frame.

Lubricate the wedges (See SERVICE SCHEDULE on Page 10-70-1.) and (See LUBRICATING THE LOADER on Page 10-140-1.)

10-130-1

T180 Service Manual

BOB-TACH (POWER)

The spring loaded wedge (Item 1) must contact the lower edge of the hole in the attachment (Item 2) [Figure 10131-2].

This machine may be equipped with a Power Bob-Tach.

Inspection And Maintenance

If the wedge does not contact the lower edge of the hole [Figure 10-131-2], the attachment will be loose and can come off the Bob-Tach.

Figure 10-131-1

Figure 10-131-3 1

2 .B-15993Q

Push and hold the BOB-TACH "WEDGES UP" switch (Item 1) until wedges are fully raised. Push and hold the BOB-TACH "WEDGES DOWN" switch (Item 2) [Figure 10-131-1] until the wedges are fully down.

The levers and wedges must move freely.

WARNING Bob-Tach wedges must extend through the holes in attachment. Lever(s) must be fully down and locked.

Failure to secure wedges can allow attachment to come off and cause injury or death.

W-2102-0497

Figure 10-131-2 1

2

B-17460

Wedge must contact lower edge of hole in the attachment.

P-31233

B-15177

The wedges (Item 1) [Figure 10-131-2] must extend through the holes in the attachment mounting frame.

Inspect the mounting frame on the attachment and the Bob-Tach, linkages and wedges for excessive wear or damage [Figure 10-131-3]. Replace any parts that are damaged, bent, or missing. Keep all fasteners tight.

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts.

Lubricate the wedges (See SERVICE SCHEDULE on Page 10-70-1.) and (See LUBRICATING THE LOADER on Page 10-140-1.)

10-131-1

T180 Service Manual

Figure 10-140-3

LUBRICATING THE LOADER Lubrication Locations Lubricate the loader as specified for the best performance of the loader. (See SERVICE SCHEDULE on Page 10-70-1.)

Record the operating hours each time you lubricate the Bobcat Loader.

3

Always use a good quality lithium based multi-purpose grease when you lubricate the loader. Apply the lubricant until extra grease shows.

Lubricate the following:

P-45253

Figure 10-140-1 3. Lift Arm Pivot Pin (Both Sides) (3) [Figure 10-140-3].

Figure 10-140-4

1

4

P-45255

1. Rod End Lift Cylinder (Both Sides) (2) [Figure 10140-1].

N-18510

4. Base End Tilt Cylinder (Both Sides) (2) [Figure 10140-4].

Figure 10-140-2

2 P-45257

2. Base End Lift Cylinder (Both Sides) (2) [Figure 10140-2].

10-140-1

T180 Service Manual

Figure 10-140-7

LUBRICATING THE LOADER (CONT’D) Lubrication Locations (Cont’d)

9

Figure 10-140-5

5 6

P-24703

NOTE: SJC equipped machines do not have a steering lever shaft.

N-18509

5. Rod End Tilt Cylinder (Both Sides) (2) [Figure 10140-5].

9. 250 Hours: Steering Lever Shaft (2) [Figure 10-1407].

6. Bob-Tach Pivot Pin (Both Sides) (2) [Figure 10-1405].

Figure 10-140-6 7

P-24699

8

P-16045

7. Bob-Tach Wedge (Both Sides) (2) [Figure 10-140-6].

8. Power Bob-Tach Cylinder (Both Sides) (2) [Figure 10-140-6]. (If Equipped)

10-140-2

T180 Service Manual

SPARK ARRESTOR MUFFLER Cleaning Procedure Use the correct service interval for cleaning the spark arrestor muffler. (See SERVICE SCHEDULE on Page 10-70-1.)

Do not operate the loader with a defective exhaust system.

WARNING When the engine is running during service, the steering levers must be in neutral and the parking brake engaged. Failure to do so can cause injury or death.

W-2006-0284

Start the engine and run for about 10 seconds while a second person, wearing safety goggles, holds a piece of wood over the outlet of the muffler.

IMPORTANT This loader is factory equipped with a U.S.D.A. Forestry Service approved spark arrestor muffler. It is necessary to do maintenance on this spark arrestor muffler to keep it in working condition. The spark arrestor muffler must be serviced by dumping the spark chamber every 100 hours of operation.

This will force contaminants out through the cleanout hole.

Stop the engine.

Install and tighten the plug.

Close the rear door.

If this machine is operated on flammable forest, brush or grass covered land, it must be equipped with a spark arrestor attached to the exhaust system and maintained in working order. Failure to do so will be in violation of California State Law, Section 4442 PRC. Consult local laws and regulations for spark arrestor requirements I-2022-0807

Stop the engine and open the rear door.

WARNING AVOID INJURY OR DEATH When an engine is running in an enclosed area, fresh air must be added to avoid concentration of exhaust fumes. If the engine is stationary, vent the exhaust outside. Exhaust fumes contain odorless, invisible gases which can kill without warning.

W-2050-0807

Figure 10-150-1

WARNING Stop engine and allow the muffler to cool before cleaning the spark chamber. Wear safety goggles.

Failure to obey can cause serious injury.

W-2011-1285

1

WARNING P-76902

Remove the plug (Item 1) [Figure 10-150-1] from the bottom of the muffler.

Never use machine in atmosphere with explosive dust or gases or where exhaust can contact flammable material. Failure to obey warnings can cause injury or death.

W-2068-1285

10-150-1

T180 Service Manual

PIVOT PINS Inspection And Maintenance Figure 10-160-1

1

P-45257

All lift arm and cylinder pivots have a large pin held in position with a retainer bolt and lock nut (Item 1) [Figure 10-160-1].

Check that the lock nuts are tightened to 35-40 ft.-lb. (4854 N•m) torque.

10-160-1

T180 Service Manual

LOADER STORAGE AND RETURN TO SERVICE

Return To Service

Storage

After the Bobcat Loader has been in storage, it is necessary to follow a list of items to return the loader to service.

Sometimes it may be necessary to store your Bobcat Loader for an extend period of time. Below is a list of items to perform before storage.

•

Check the engine and hydraulic oil levels; check coolant level.

•

Install a fully charged battery.

•

Remove grease from exposed cylinder rods.

•

Check all belt tensions.

•

Be sure all shields and guards are in place.

•

Lubricate the loader.

•

Check track condition and remove blocks from under frame.

•

Remove cover from exhaust pipe opening.

•

Start the engine and let run for a few minutes while observing the instrument panels and systems for correct operation.

•

Operate machine, check for correct function.

•

Stop the engine and check for leaks. Repair as needed.

10-170-1

T180 Service Manual

•

Thoroughly clean the loader including the engine compartment.

•

Lubricate the loader.

•

Replace worn or damaged parts.

•

Park the loader in a dry protected shelter.

•

Lower the lift arms all the way and put the bucket flat on the ground.

•

Put blocks under the frame to remove weight from the tracks.

•

Put grease on any exposed cylinder rods.

•

Put fuel stabilizer in the fuel tank and run the engine a few minutes to circulate the stabilizer to the pump and fuel injectors.

If biodiesel blend fuel has been used, perform the following: Drain the fuel tank, refill with 100% petroleum diesel fuel, add fuel stabilizer and run the engine for at least 30 minutes.

•

Drain and flush the cooling system. Refill with premixed coolant.

•

Replace all fluids and filters (engine, hyd. / hydro.).

•

Replace air cleaner, heater and air conditioning filters.

•

Put all controls in neutral position.

•

Remove the battery. Be sure the electrolyte level is correct then charge the battery. Store it in a cool dry place above freezing temperatures and charge it periodically during storage.

•

Cover the exhaust pipe opening.

•

Tag the machine to indicate that it is in storage condition.

NOTE: Activating the Password Lockout Feature on machines with the Deluxe Instrumentation Panel allows operation of the loader without using a password. (See Password Lockout Feature on Page 60-190-2.)

STOPPING THE ENGINE AND LEAVING THE LOADER Procedure Stop the loader on level ground.

Fully lower the lift arms and put the attachment flat on the ground.

Figure 10-180-3

Figure 10-180-1

P-66667A

Exit the loader using grab handles, safety tread and steps (maintaining a 3-point contact) [Figure 10-180-1].

P-31864

Pull the engine speed control fully backward [Figure 10180-1] to decrease the engine speed.

WARNING

Engage the parking brake.

Figure 10-180-2

1

2 P-76603

P-66668A

B-15553L

Turn the key switch to the STOP position (Item 1) (Standard Key Panel) or press the STOP button (Item 2) (Deluxe Instrumentation Panel) [Figure 10-180-2].

Lift the seat bar and make sure the lift and tilt functions are deactivated.

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar.

• (Foot Pedal Controls) Move pedals until both lock.

• (Advanced Control System-ACS) Move the hydraulic controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up.

Service the system if hand controls do not deactivate.

• (Selectable Joystick Controls-SJC) Move the joysticks to the NEUTRAL POSITION to make sure that travel and hydraulic functions are deactivated.

The seat bar system must deactivate these functions when the seat bar is up. Service the system if controls do not deactivate.

W-2463-0603

Unbuckle the seat belt.

Remove the key from the switch (Standard Key Panel) to prevent operation of the loader by unauthorized personnel.

10-180-1

T180 Service Manual

Front Door (If Equipped)

STOPPING THE ENGINE AND LEAVING THE LOADER (CONT’D) Emergency Exit The front opening on the operator cab and rear window provide exits.

NOTE: When an Operator Cab Enclosure Kit is installed, the window of the front door can be used as an emergency exit. [Figure 10-180-6]

Rear Window (If Equipped)

NOTE: If the loader has a Special Application Door Kit installed, the window of the front door is NOT an emergency exit.

Figure 10-180-4

Figure 10-180-6

P-64994

N-20171

Pull on the tag on the top of the rear window to remove the rubber cord [Figure 10-180-4].

Pull the plastic loop at the top of the window in the front door to remove the rubber cord [Figure 10-180-6].

Push the rear window out of the rear of the operator cab.

Figure 10-180-7

Figure 10-180-5

X X

X X S0363

P-45260

Exit through the rear of the operator cab [Figure 10-1805].

Push the window out with your foot at any corner of the window [Figure 10-180-7].

Exit through the front door.

10-180-2

T180 Service Manual

HYDRAULIC SYSTEM BOB-TACH (POWER) BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-130-1 20-130-1 20-130-3 20-130-1

BUCKET POSITION VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . .

Solenoid Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-110-1 20-110-1 20-110-4 20-110-3 20-110-1 20-110-2

CYLINDER (LIFT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-20-1 20-20-4 20-20-3 20-20-2 20-20-1

CYLINDER (BOB-TACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-22-1 20-22-4 20-22-3 20-22-2 20-22-1

CYLINDER (TILT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Base End Pivot Pin Removal And Installation . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rod End Pivot Pin Bushing And Seal Removal And Installation . . .

Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-21-1 20-21-4 20-21-6 20-21-5 20-21-2 20-21-4 20-21-1

FRONT AUXILIARY HYDRAULIC COUPLER BLOCK. . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-140-1 20-140-1 20-140-1 20-140-1

HIGH FLOW VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

High Flow Relief Valve Adjustment . . . . . . . . . . . . . . . . . . . . . . . .

High Flow Relief Valve Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Solenoid Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-150-1 20-150-1 20-150-5 20-150-2 20-150-1 20-150-4 20-150-3

HYDRAULIC SYSTEM

Continued On Next Page

20-01

T180 Service Manual

HYDRAULIC SYSTEM (CONT’D) HYDRAULIC CONTROL VALVE (ACS) OR (SJC) . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-1 Actuator Removal And Installation (Out of Loader) . . . . . . . . . . . . . . . . . . . . . . . 20-41-6 Anti-Cavitation Valve Removal And Installation (Lift, Rod End) . . . . . . . . . . . . . 20-41-12 Auxiliary Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-25 Auxiliary Spool Removal And Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-24 Check Valve Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-32 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-1 End Cap Block Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-16 Identification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-9 Load Check Valve Removal And Installation (Tilt & Auxiliary) . . . . . . . . . . . . . . 20-41-11 Lift Arm Bypass Orifice Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . 20-41-30 Lift Load Check Valve Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . 20-41-10 Lift Spool And Detent Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . 20-41-17 Lock Valve Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-28 Main Relief Valve Removal And Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-31 Mount Bracket Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-10 Plug Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-15 Port Relief/Anti-Cavitation Valve Removal And Installation (Lift, Base End) . . . 20-41-13 Port Relief/Anti-Cavitation Valve Removal And Installation (Tilt, Base End) . . . 20-41-13 Port Relief/Anti-Cavitation Valve Removal And Installation (Tilt, Rod End) . . . . 20-41-14 Port Relief Valve Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-14 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-1 Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-26 Tilt Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-22 HYDRAULIC CONTROL VALVE (STANDARD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-1 Anti-Cavitation Valve Removal And Installation (Lift, Rod End) . . . . . . . . . . . . . . 20-40-9 Auxiliary Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-28 Auxiliary Spool Removal And Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-27 Check Valve Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-34 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-1 End Cap / Spool Lock Block Removal And Installation . . . . . . . . . . . . . . . . . . . 20-40-14 Identification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-6 Lift Arm Bypass Orifice Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . 20-40-33 Lift Load Check Valve Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-7 Lift Spool And Detent Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . 20-40-15 Lock Valve Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-31 Load Check Valve Removal And Installation (Tilt & Auxiliary) . . . . . . . . . . . . . . . 20-40-8 Main Relief Valve Removal And Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-33 Mount Bracket Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-7 Plug Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-12 Port Relief / Anti-Cavitation Valve Removal And Installation (Lift, Base End) . . 20-40-10 Port Relief / Anti-Cavitation Valve Removal And Installation (Tilt, Base End) . . 20-30-10 Port Relief / Anti-Cavitation Valve Removal And Installation (Tilt, Rod End) . . . 20-40-11 Port Relief Valve Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-11 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-1 Rubber Boot Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-13 Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-29 Tilt Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-25 Continued On Next Page 20-02

T180 Service Manual

HYDRAULIC SYSTEM (CONT’D) HYDRAULIC / HYDROSTATIC FILTERS . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Charge Filter Housing Removal And Installation . . . . . . . .

Housing Removal And Installation . . . . . . . . . . . . . . . . . . .

20-80-1 20-80-1 20-80-3 20-80-1

HYDRAULIC FLUID RESERVOIR . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic Fluid Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . .

20-90-1 20-90-1 20-90-3 20-90-1

HYDRAULIC PUMP (STANDARD) . . . . . . . . . . . . . . . . . . . . . 20-60-1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-60-1 Direct Pump Test (Charge Section) . . . . . . . . . . . . . . . . . . 20-60-4 Direct Pump Test (Standard Section). . . . . . . . . . . . . . . . . 20-60-2 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . 20-60-10 Hydraulic Pump Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-60-8 Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-60-9 Pump Test at Quick Couplers . . . . . . . . . . . . . . . . . . . . . . 20-60-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 20-60-6 HYDRAULIC PUMP (STANDARD) (HIGH FLOW) . . . . . . . . . 20-61-1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-61-1 Direct Pump Test (Charge Section) . . . . . . . . . . . . . . . . . . 20-61-4 Direct Pump Test (High Flow Section) . . . . . . . . . . . . . . . . 20-61-6 Direct Pump Test (Standard Section). . . . . . . . . . . . . . . . . 20-61-2 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . 20-61-12 Hydraulic Pump Startup . . . . . . . . . . . . . . . . . . . . . . . . . . 20-61-10 Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-61-11 Pump Test at Quick Couplers . . . . . . . . . . . . . . . . . . . . . . 20-61-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 20-61-8 HYDRAULIC PUMP (SJC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-1 Direct Pump Test (Charge Section) . . . . . . . . . . . . . . . . . . 20-70-4 Direct Pump Test (Standard Section). . . . . . . . . . . . . . . . . 20-70-2 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . 20-70-10 Hydraulic Pump Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-8 Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-9 Pump Test At Quick Couplers . . . . . . . . . . . . . . . . . . . . . . 20-70-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-6 Continued On Next Page

20-03

T180 Service Manual

HYDRAULIC SYSTEM (CONT’D) HYDRAULIC PUMP (SJC) (HIGH FLOW) . . . . . . . . . . . . . . . . . . . . 20-71-1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-71-1 Direct Pump Test (Charge Section) . . . . . . . . . . . . . . . . . . . . . . . 20-71-4 Direct Pump Test (High Flow Section) . . . . . . . . . . . . . . . . . . . . . 20-71-6 Direct Pump Test (Standard Section). . . . . . . . . . . . . . . . . . . . . . 20-71-2 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-71-12 Hydraulic Pump Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-71-24 Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-71-11 Pump Test at Quick Couplers . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-71-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-71-8 HYDRAULIC SYSTEM INFORMATION . . . . . . . . . . . . . . . . . . . . . . 20-10-1 Glossary Of Hydraulic / Hydrostatic Symbols . . . . . . . . . . . . . . . 20-10-1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-10-5 LIFT ARM BYPASS CONTROL VALVE . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-50-1 20-50-1 20-50-2 20-50-1 20-50-1

MAIN RELIEF VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-30-1 20-30-3 20-30-1 20-30-4 20-30-1

OIL COOLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-100-1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-100-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-100-1 REAR AUXILIARY DIVERTER VALVE . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Solenoid Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-120-1 20-120-1 20-120-5 20-120-2 20-120-1

TIGHTEN ALL HARDWARE PER SIZE TO GRADE 5 TORQUE (SEE STANDARD TORQUE SPECIFICATIONS FOR BOLTS, SECTION SPEC01) UNLESS OTHERWISE SPECIFIED.

20-04

T180 Service Manual

Thank you very much for your reading.

Please Click Here Then Get More Information.