BOBCAT S175 SKID STEER LOADER Service Repair Manual SN A3L511001-A3L519999

Service Manual S175 Skid-Steer Loader S/N A3L511001 - A3L519999

EQUIPPED WITH BOBCAT INTERLOCK CONTROL SYSTEM (BICS) 6986567 (5-08)

Printed in U.S.A.

© Bobcat Company 2008

ALPHABETICAL INDEX ACCESS PANEL (INSIDE) ..................................... 50-01 ACCESS PANEL (INSIDE) (SJC) ...........................50-01 AIR CLEANER .................................................... 70-01 AIR CLEANER SERVICE ....................................... 10-01 AIR CONDITIONING SYSTEM FLOW ................... 80-01 ALTERNATOR ........................................................ 60-01

FINAL DRIVE TRANSMISSION (CHAINCASE) .. 10-01 FLYWHEEL AND HOUSING ................................ 70-01 FLYWHEEL RPM SENSOR ....................................60-01 FRONT AUXILIARY HYD. COUPLER BLOCK .......20-01 FUEL SYSTEM.............................................10-01, 70-01 FUEL TANK .............................................................50-01

BATTERY................................................................ 60-01 BLOWER FAN ........................................................ 80-01 BLOWER FAN ........................................................80-01 BOBCAT INTERLOCK CONTROL SYSTEM (BICS) ................................................... 60-01 BOBCAT CONTROLLER .....................................60-01 BOB-TACH (HAND LEVER) ........................ 10-01, 50-01 BOB-TACH (POWER)............................................. 50-01 BRAKE (SINGLE SPEED) ...................................... 40-01 BRAKE (TWO-SPEED)........................................... 40-01 BUCKET POSITION VALVE ................................20-01

HEATER COIL .........................................................80-01 HEATER SYSTEM...................................................80-01 HEATER UNIT .........................................................80-01 HEATER VALVE ......................................................80-01 HIGH FLOW VALVE ................................................20-01 HYDRAULIC CONNECTION SPECS. .............. SPEC-01 HYDRAULIC CONTROL VALVE .............................20-01 HYD./HYDRO FLUID SPECIFICATIONS .......... SPEC-01 HYDRAULIC FLUID RESERVOIR ..........................20-01 HYDRAULIC/HYDROSTATIC FILTERS ..................20-01 HYDRAULIC/HYDROSTATIC SYSTEM..................10-01 HYDRAULIC PUMP (STANDARD)..........................20-01 HYDRAULIC PUMP (STANDARD) (HIGH FLOW)..20-01 HYDRAULIC PUMP (HIGH FLOW) (SJC)...............20-01 HYDARULIC PUMP (SJC) ......................................20-01 HYDRAULIC SYSTEM INFORMATION ..................20-01 HYDROSTATIC MOTOR ..................................... 30-01 HYDROSTATIC MOTOR (TWO SPEED) ................30-01 HYDROSTATIC MOTOR CARRIER (SINGLE ANDTWO-SPEED WITH MANUAL CONTROLS) .........................................................30-01 HYDROSTATIC MOTOR CARRIER (SINGLE ANDTWO-SPEED WITH SJC CONTROLS) .........................................................30-01 HYDROSTATIC PUMP ........................................ 30-01 HYDROSTATIC PUMP (SJC) ............................. 30-01 HYDROSTATIC SYSTEM INFORMATION ..........30-01

CALIBRATION ........................................................ 60-01 CAMSHAFT AND TIMING GEARS.........................70-01 CHAINCASE ........................................................... 40-01 CHARGE PRESSURE ............................................ 30-01 CONTROL HANDLE/LEVER .................................. 50-01 CONTROL HANDLE/LEVER (ACS) ....................... 50-01 CONTROL HANDLE/LEVER (SJC) ........................ 50-01 CONTROL PANEL .................................................. 50-01 CONTROL PANEL (SJC)........................................ 50-01 CONTROL PEDALS AND LINKAGE ...................... 50-01 CONTROL PEDALS (ACS) .................................... 50-01 CONTROL SYSTEM (ACS) .................................... 60-01 CONVERSIONS ............................................SPEC-01 CRANKSHAFT AND PISTONS .............................. 70-01 CYLINDER (LIFT) ................................................... 20-01 CYLINDER (BOB-TACH) ........................................ 20-01 CYLINDER (TILT) ................................................ 20-01 CYLINDER HEAD ................................................... 70-01 DIAGNOSTICS SERVICE CODES ..................... 60-01 DRIVE BELT ........................................................... 30-01 DRIVE COMPONENTS .......................................... 40-01 ELECTRICAL SYSTEM INFORMATION ................ 60-01 ELECTRICAL/HYRAULIC CONTROLS.................. 60-01 ELECTRICAL/HYRAULIC CONTROLS (SJC)........ 60-01 ENGINE COOLING SYSTEM ...................... 10-01, 70-01 ENGINE INFORMATION ........................................ 70-01 ENGINE LUBRICATION SYSTEM.......................... 10-01 ENGINE SPEED CONTROL (SJC) ........................ 70-01

INSTRUMENT PANELS ..........................................60-01 LIFT ARMS ..............................................................50-01 LIFT ARM BYPASS CONTROL VALVE .............. 20-01 LIFT ARM SUPPORT DEVICE ........................... 10-01 LIFTING AND BLOCKING THE LOADER...............10-01 LIGHTS ................................................................60-01 LOADER STORAGE AND RETURN TO SERVICE 10-01 LUBRICATING THE LOADER.................................10-01 LUBRICATION SYSTEM .........................................70-01 MAIN RELIEF VALVE ..............................................20-01 MUFFLER................................................................70-01 OIL COOLER...........................................................20-01 OPERATOR CAB .........................................10-01, 50-01 OPERATOR SEAT...................................................50-01 OPERATOR SEAT (SUSPENSION)........................50-01 PIVOT PINS ............................................................10-01 POWER BOB-TACH BLOCK...................................20-01

S175 Service Manual

ALPHABETICAL INDEX (CONT’D) REAR AUXILIARY DIVERTER VALVE ....................20-01 REAR DOOR ...................................................... 50-01 REAR GRILL ...........................................................50-01 REGULAR MAINTENANCE ................................... 80-01 REMOTE START TOOL KIT-MEL1563 ...............10-01 REMOTE START TOOL (SERVICE TOOL) KIT-6689779 ..........................................................10-01 S175 LOADER SPECIFICATIONS .................... SPEC-01 S185 LOADER SPECIFICATIONS .................... SPEC-01 SEAT BAR ...............................................................50-01 SEAT BAR SENSOR ...............................................60-01 SERVICE PC (LAPTOP COMPUTER) ....................60-01 SERVICE SCHEDULE ............................................10-01 SPARK ARRESTOR MUFFLER ............................. 10-01 SPEED SENSORS (SJC)....................................... 60-01 STARTER ................................................................60-01 STEERING DRIFT COMPENSATION .....................60-01 STOPPING THE ENGINE AND LEAVING THE LOADER .......................................10-01 SYSTEM CHARGING AND RECLAMATION ......... 80-01 TIRE MAINTENANCE .............................................10-01 TORQUE SPECIFICATIONS FOR BOLTS .... SPEC-01 TOWING THE LOADER ..........................................10-01 TRACTION LOCK....................................................60-01 TRANSPORTING LOADER ON A TRAILER ..........10-01 TROUBLESHOOTING.............................................80-01 TURBOCHARGER ..................................................70-01 TWO-SPEED VALVE ...............................................30-01 WINDOW (FRONT DOOR) .....................................50-01 WINDOW (REAR)................................................... 50-01 WINDOW (SIDE) .................................................... 50-01 WINDOW (TOP) ..................................................... 50-01

S175 Service Manual

MAINTENANCE SAFETY WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0903

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

CORRECT

B-10731a

Never service the Bobcat SkidSteer Loader without instructions.

WRONG

B-15734

Have good ventilation when welding or grinding painted parts.

Wear dust mask when grinding painted parts. Toxic dust and gas can be produced.

Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed.

CORRECT

CORRECT

B-15535

Use the correct procedure to lift or lower operator cab.

B-15524

Cleaning and maintenance are required daily.

WRONG

WRONG

B-15732

B-15525

Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported by an approved lift arm support device. Replace it if damaged.

Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged.

Never modify equipment or add attachments not approved by Bobcat Company.

WRONG

WRONG

WRONG

B-15733

B-15523 B-16102

B-6589 B-16102

Stop, cool and clean engine of flammable materials before checking fluids.

Never service or adjust loader with the engine running unless instructed to do so in the manual.

Avoid contact with leaking hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes.

Never fill fuel tank with engine running, while smoking or when near open flame.

Keep body, jewelry and clothing away from moving parts, electrical contact, hot parts and exhaust.

Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used.

Use eye protection approved for type of welding.

Keep rear door closed except for service. Close and latch door before operating the loader.

Lead-acid batteries produce flammable and explosive gases.

Keep arcs, sparks, flames and lighted tobacco away from batteries.

Batteries contain acid which burns eyes or skin on contact.

Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate medical attention.

Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/ operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer.

MSW07-0805

SAFETY & MAINTENANCE

CONTENTS FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V

HYDRAULIC SYSTEM

FIRE PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VII SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX

HYDROSTATIC SYSTEM

DELIVERY REPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X LOADER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XI SAFETY AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . 10-01

DRIVE SYSTEM

HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-01 MAIN FRAME HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-01 DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-01 MAIN FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-01

ELECTRICAL SYSTEM & ANALYSIS

ELECTRICAL SYSTEM & ANALYSIS. . . . . . . . . . . . . . . . . . . . . 60-01 ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-01

ENGINE SERVICE

HEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80-01 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-01

HEATER

SPECIFICATIONS

SPECIFICATIONS

i

S175 Service Manual

FOREWORD This manual is for the Bobcat loader mechanic. It provides necessary servicing and adjustment procedures for the Bobcat loader and its component parts and systems. Refer to the Operation & Maintenance Manual for operating instructions, Starting procedure, daily checks, etc.

A general inspection of the following items must be made after the loader has had service or repair: 1. Check lift arm support device, replace if damaged. (Stored Position)

9. The parking brake function correctly.

2. Check that ROPS mounting hardware is tightened and is Bobcat approved.

10. Enclosure door latches must open and close freely.

3. The seat belt must be correctly installed, functional and in good condition.

11. Bob-Tach wedges and linkages must function correctly and be in good condition.

4. The seat bar must be correctly adjusted, clean and lubricated.

12. Safety treads must be in good condition.

5. Check lift arm support device; replace if damaged.

13. Check for correct function of indicator lamps (Optional on some models).

6. Machine signs must be legible and in the correct location.

14. Check hydraulic fluid level, engine oil level and fuel supply.

7. Steering levers and foot pedals must return to neutral.

15. Inspect for fuel, hydraulic fluid leaks.

8. Check for correct function of the work lights

16. Lubricate the loader.

ii

must

oil

or

S175 Service Manual

17. Check the condition of the battery and cables.

22. Operate the loader and check all functions.

18. Inspect the air cleaner for damage or leaks. Check the condition of the element.

23. Check for any field modification not completed.

19. Check the electrical charging system.

24. Check for correct function of the Bobcat Interlock Control System (BICS™) before the machine is returned to the customer.

20. Check tires for wear and pressure.

Recommend to the owner that all necessary corrections be made before the machine is returned to service.

21. Inspect for loose or broken parts or connections.

CALIFORNIA PROPOSITION 65 WARNING Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

iii

S175 Service Manual

SAFETY INSTRUCTIONS

The following publications provide information on the safe use and maintenance of the Bobcat machine and attachments:

Safety Alert Symbol This symbol with a warning statement means: “Warning, be alert! Your safety is involved!”

Carefully read the message that follows.

•

The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine is in safe operating condition.

•

The Operation & Maintenance Manual delivered with the machine or attachment contains operating information as well as routine maintenance and service procedures. It is a part of the machine and can be stored in a container provided on the machine.

Replacement Operation & Maintenance Manuals can be ordered from your Bobcat dealer.

•

Machine signs (decals) instruct on the safe operation and care of your Bobcat machine or attachment. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat dealer.

•

An Operator’s Handbook fastened to the operator cab. It’s brief instructions are convenient to the operator. The handbook is available from your dealer in an English edition or one of many other languages.

See your Bobcat dealer for more information on translated versions.

•

The AEM Safety Manual delivered with the machine gives general safety information.

•

The Service Manual and Parts Manual are available from your dealer for use by mechanics to do shoptype service and repair work.

•

The Skid-Steer Loader Operator Training Course is available through your local dealer or at www.training.bobcat.com or www.bobcat.com.

This course is intended to provide rules and practices of correct operation of the Skid-Steer Loader. The course is available in English and Spanish versions.

•

Service Safety Training Courses are available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com. They provide information for safe and correct service procedures.

•

The Skid-Steer Loader Safety Video is available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com.

WARNING Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service.

Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0903

WARNING Warnings on the machine and in the manuals are for your safety. Failure to obey warnings can cause injury or death.

W-2044-1285

IMPORTANT This notice identifies procedures which must be followed to avoid damage to the machine.

I-2019-0284

SI SSL-1007 SM

v

S175 Service Manual

Hydraulic System

FIRE PREVENTION

Check hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Hydraulic tubes and hoses must be properly routed and have adequate support and secure clamps.

Tighten or replace any parts that show leakage.

Maintenance

Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.

The machine and some attachments have components that are at high temperatures under normal operating conditions. The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a source of arcs or sparks.

Fueling

Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it can cause a fire hazard. Clean often to avoid this accumulation. Flammable debris in the engine compartment is a potential fire hazard.

Stop the engine and let it cool before adding fuel. No smoking! Do not refuel a machine near open flames or sparks. Fill the fuel tank outdoors.

The operator’s area, engine compartment and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazards and overheating.

Starting Do not use ether or starting fluids on any engine that has glow plugs. These starting aids can cause explosion and injure you or bystanders.

All fuels, most lubricants and some coolants mixtures are flammable. Flammable fluids that are leaking or spilled onto hot surfaces or onto electrical components can cause a fire.

Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting.

Operation Do not use the machine where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases.

Spark Arrestor Exhaust System The spark arrestor exhaust system is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the exhaust gases are still hot.

Electrical

Check the spark arrestor exhaust system regularly to make sure it is maintained and working properly. Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrestor muffler (if equipped).

Check all electrical wiring and connections for damage.

Keep the battery terminals clean and tight. Repair or replace any damaged part or wires that are loose or frayed.

Battery gas can explode and cause serious injury. Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump staring. Do not jump start or charge a frozen or damaged battery. Keep any open flames or sparks away from batteries. Do not smoke in battery charging area.

SI SSL-1007 SM

vii

S175 Service Manual

FIRE PREVENTION (CONT’D) Welding And Grinding Always clean the machine and attachment, disconnect the battery, and disconnect the wiring from the Bobcat controllers before welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the machine when welding.

Have good ventilation when grinding or welding painted parts. Wear dust mask when grinding painted parts.

Toxic dust or gas can be produced.

Dust generated from repairing nonmetallic parts such as hoods, fenders or covers can be flammable or explosive.

Repair such components in a well ventilated area away from open flames or sparks.

Fire Extinguishers

Know where fire extinguishers and first aid kits are located and how to use them. Inspect the fire extinguisher and service the fire extinguisher regularly.

Obey the recommendations on the instructions plate.

SI SSL-1007 SM viii

S175 Service Manual

SERIAL NUMBER LOCATIONS

Engine Serial Number

Always use the serial number of the loader when requesting service information or when ordering parts.

Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

Figure 2

Loader Serial Number Figure 1

P-48387

The engine serial number is in the location shown [Figure 2].

P-31846

The loader serial number plate is located on the outside of the loader frame [Figure 1].

Explanation of loader Serial Number: XXXX Model 1.-Model/ Engine Combination

XXXXX Model 2.-Production Sequence (Series)

1. The four digit Model/Engine Combination Module number identifies the model number and engine combination.

2. The five digit Production Sequence Number identifies the order which the loader is produced.

ix

S175 Service Manual

DELIVERY REPORT Figure 3

B-16315

The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [Figure 3].

x

S175 Service Manual

LOADER IDENTIFICATION FRONT LIGHTS

OPERATOR SEAT WITH SEAT BELT

SEAT BAR REAR AUXILIARY QUICK COUPLERS

GRAB HANDLES STEERING LEVER TILT CYLINDER

STABILIZER ROD

† BUCKET

FRONT AUXILIARY QUICK COUPLERS

BUCKET STEPS

SAFETY TREAD

zOPERATOR CAB (ROPS & FOPS)

REAR WINDOW LIFT ARM LINK REAR GRILL

LIFT ARM LIFT CYLINDER

TAIL LIGHT

LIFT ARM SUPPORT DEVICE REAR LIGHT

REAR DOOR

* TIRES B-16604 B-16605

OPTIONAL OR FIELD ACCESSORY (Not Standard Equipment) * TIRES - The Bobcat loader is factory equipped with heavy duty flotation tires. See Specifications Section and your Bobcat dealer for available tires. † BUCKET - Several different buckets and other attachments are available for the Bobcat loader. z ROPS, FOPS - Roll Over Protective Structure, per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAEJ1043 and ISO 3449, Level I. Level II is available. The Bobcat loader is base-equipped with a standard operator cab as shown. Extra insulated cab is available as an option (Reduced noise level).

xi

S175 Service Manual

SAFETY & MAINTENANCE

SAFETY AND MAINTENANCE AIR CLEANER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 Replacing Filter Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1

SAFETY & BOB-TACH (HAND LEVER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 MAINTENANCE Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 BOB-TACH (POWER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-141-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-141-1 ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing And Replacing Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking And Adding Engine Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine Oil Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing And Replacing Oil And Filter. . . . . . . . . . . . . . . . . . . . . . . . . .

10-90-1 10-90-2 DRIVE 10-90-1 SYSTEM 10-90-2

10-110-1 10-110-1 10-110-1 10-110-2

ELECTRICAL FINAL DRIVE TRANSMISSION (CHAINCASE) . . . . . . . . . . . . . . . . . . . . . . 10-130-1 SYSTEM & Checking And Adding Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 ANALYSIS Removing And Replacing Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Biodiesel Blend Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Filling the Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing Air From The Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-100-1 ENGINE 10-100-1 SERVICE 10-100-2 10-100-3 10-100-1 10-100-3 SPECIFICATIONS

HYDRAULIC/HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-1 Breather Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-7 Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-1 Hydraulic / Hydrostatic Fluid Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-1 Removing And Replacing Hydraulic Fluid . . . . . . . . . . . . . . . . . . . . . . . . 10-120-2 Removing And Replacing Hydraulic/Hydrostatic Filter . . . . . . . . . . . . . . 10-120-2 Removing And Replacing Hydraulic Case Drain Filters (Single Speed Loaders)10120-3 Removing And Replacing Hydraulic Case Drain Filters (Two-Speed Loaders) . 10120-4 Removing And Replacing Hydraulic Charge Filter. . . . . . . . . . . . . . . . . . 10-120-6 LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Installing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Removing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-2 Continued On Next Page

10-01

S175 Service Manual

SAFETY AND MAINTENANCE (CONT’D) LIFTING AND BLOCKING THE LOADER . . . . . . . . . . . . . . . . . . . 10-10-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10-1 LOADER STORAGE AND RETURN TO SERVICE . . . . . . . . . . . 10-190-1 Return to Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-190-1 Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-190-1 LUBRICATING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1 Lubrication Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1 OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cab Door Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lowering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Raising . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Applications Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Applications Kit Inspection And Maintenance . . . . . . . .

10-30-1 10-30-1 10-30-4 10-30-3 10-30-2 10-30-4 10-30-4

PIVOT PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1 REMOTE START TOOL KIT-MEL1563. . . . . . . . . . . . . . . . . . . . . .

Remote Start Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Remote Start Tool - MEL1563 . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Tool Harness Communicator - MEL1566 . . . . . . . . . . .

Remote Start Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-60-1 10-60-4 10-60-1 10-60-3 10-60-4

REMOTE START TOOL (SERVICE TOOL) KIT - 6689779 . . . . . .

Computer Service Tool Harness - 6689746 . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loader Service Tool Harness - 6689747 . . . . . . . . . . . . . . . . . .

Remote Start Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Remote Start Tool (Service Tool) - 6689778 . . . . . . . . . . . . . . .

10-61-1 10-61-4 10-61-1 10-61-3 10-61-5 10-61-2

SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 SPARK ARRESTOR MUFFLER . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1 Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1 STOPPING THE ENGINE AND LEAVING THE LOADER . . . . . . 10-200-1 Emergency Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-200-2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-200-1 Continued On Next Page

10-02

S175 Service Manual

SAFETY AND MAINTENANCE (CONT’D) TIRE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rotating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-160-1 10-160-1 10-160-1 10-160-1

TOWING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 TRANSPORTING LOADER ON A TRAILER . . . . . . . . . . . . . . . . . 10-40-1 Fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1 Loading And Unloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1 TIGHTEN ALL HARDWARE PER SIZE TO GRADE 5 TORQUE (SEE STANDARD TORQUE SPECIFICATIONS FOR BOLTS, SPEC SECTION) UNLESS OTHERWISE SPECIFIED.

10-03

S175 Service Manual

LIFTING AND BLOCKING THE LOADER

Figure 10-10-2

Procedure Figure 10-10-1

N-18877

Put the floor jack under the front of the loader [Figure 1010-2].

B-7023A

Lift the front of the loader and put jackstands under the axle tubes [Figure 10-10-2].

WARNING AVOID INJURY OR DEATH Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service.

Untrained operators and failure to follow instructions can cause injury or death.

NOTE: Make sure the jackstands do not touch the tires. Make sure tires clear floor or any obstacles.

Figure 10-10-3

W-2003-0807

Always park the loader on a level surface.

WARNING

P-31849

Put jackstands under the front axles and rear corners of the frame before running the engine for service.

Failure to use jackstands can allow the machine to fall or move and cause injury or death.

W-2017-0286

Put the floor jack under the rear of the loader [Figure 1010-3].

Lift the rear of the loader and install jackstands [Figure 10-10-3].

10-10-1

S175 Service Manual

The operator must be in the operator's seat, with the seat belt fastened and seat bar lowered, until the lift arm support device is installed.

LIFT ARM SUPPORT DEVICE Installing

Start the engine, and raise the lift arms all the way up.

WARNING

Figure 10-20-2 N-18483

Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death.

1

Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death.

W-2572-0407

P-31854A

Have a second person install the lift arm support device (Item 1) [Figure 10-20-2] over the rod of one of the lift cylinders.

Remove attachment from the loader. (See Removal And Installation on Page 50-40-1.) OR (See Removal And Installation on Page 50-41-1.)

The lift arm support device must be tight against the cylinder rod. The tabs of the lift arm support device must be under the cylinder as shown (Inset) [Figure 10-20-2].

Figure 10-20-1

P-31849

1

N-18488

Put jackstands under the rear corners of the loader frame (Inset) [Figure 10-20-1] Remove the lift arm support device (Item 1) [Figure 1020-1] from storage position.

10-20-1

S175 Service Manual

LIFT ARM SUPPORT DEVICE (CONT’D)

Removing

Installing (Cont’d)

The operator must be in the operator's seat, with the seat belt fastened and seat bar lowered, until the lift arm support device is removed and the lift arms are lowered all the way.

Figure 10-20-3

Start the engine, raise the lift arms all the way up.

Have a second person remove the lift arm support device.

1

Lower the lift arms all the way and stop the engine.

Return the lift arm support device to storage position and secure with clamping knobs.

Remove the jackstands.

P-31855A

Lower the lift arms slowly until the lift arm support device (Item 1) [Figure 10-20-3] is held between the lift arms and lift cylinder .

10-20-2

S175 Service Manual

OPERATOR CAB Description The Bobcat loader has an operator cab (ROPS and FOPS) as standard equipment to protect the operator from rollover and falling objects. Check with your dealer if the operator cab has been damaged. The seat belt must be worn for roll over protection.

ROPS/FOPS - Roll Over Protective Structure per ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level I. Level II is available.

Level I - Protection from falling bricks, small concrete blocks, and hand tools encountered in operations such as highway maintenance, landscaping, and other construction site services.

Level II - Protection from falling trees, rocks; for machines involved in site clearing, overhead demolition or forestry.

WARNING Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Bobcat Company. Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death.

W-2069-0200

10-30-1

S175 Service Manual

OPERATOR CAB (CONT'D) Raising Always stop the engine before raising or lowering the cab.

Stop the loader on a level surface. Lower the lift arms. If the lift arms must be up while raising the operator cab, install the lift arm support device. (See LIFT ARM SUPPORT DEVICE on Page 10-20-1.)

Figure 10-30-1

NOTE: On Advanced Control System (ACS) equipped machines, the steering levers could contact the cab frame while raising or lowering the operator cab. The engine MUST be stopped before raising or lowering the cab.

Figure 10-30-3

P-31849

Install jackstands under the rear of the loader frame [Figure 10-30-1].

Figure 10-30-2 P-31858A

Lift on the grab handle and bottom of the operator cab slowly until the cab is all the way up and the latching mechanism engages [Figure 10-30-3].

P10564

P10563

Remove the nuts and plates [Figure 10-30-2] (both sides) at the front corners of the cab.

10-30-2

S175 Service Manual

Support the cab and release the latching mechanism (Inset) [Figure 10-30-4]. Remove your hand from latching mechanism when the cab is past the latch stop.

Use both hands to lower the cab all the way.

OPERATOR CAB (CONT'D) Lowering Always stop the engine before raising or lowering the cab.

WARNING

NOTE: Always use the grab handles to lower the cab.

Figure 10-30-4

PINCH POINT CAN CAUSE INJURY Remove your hand from the latching mechanism when the cab is past the latch stop.

W-2469-0803

Figure 10-30-5

N-20120

P-31859 P10563

Pull down on the bottom of the operator cab until it stops at the latching mechanism [Figure 10-30-4].

NOTE: The weight of the cab increases when equipped with options and accessories such cab door, heater, air conditioning, etc. In these cases, the cab may need to be raised slightly from the latch to be able to release the latch.

P10564

P10563

Install the plates and nuts [Figure 10-30-5] (both sides).

Tighten the nuts to 40-45 ft.-lb. (54-61 N•m) torque.

NOTE: On Advanced Control System (ACS) equipped machines, the steering levers could contact the cab frame while raising or lowering the operator cab. The engine MUST be stopped before raising or lowering the cab.

10-30-3

S175 Service Manual

OPERATOR CAB (CONT’D)

Special Applications Kit

Cab Door Sensor

Figure 10-30-7

Figure 10-30-6 3

B-15551j

1 B-25286A

2

P-68116

Available for special applications to restrict material from entering cab openings. Kit includes 1/2 inch Lexan™ front door, top and rear windows [Figure 10-30-7].

P-68115

Cab doors have a sensor (Item 1) [Figure 10-30-6] installed which deactivates the lift and tilt valves when the door is open.

See your Bobcat dealer for availability.

CLOSE DOOR TO OPERATE lift and tilt valves.

• • •

Special Applications Kit Inspection And Maintenance

• • •

Inspect for cracks or damage. Replace if required.

Pre-rinse with water to remove gritty materials.

Wash with a mild household detergent and warm water.

Use a sponge or soft cloth. Rinse well with water and dry with a clean soft cloth or rubber squeegee.

Do not use abrasive or highly alkaline cleaners.

Do not operate windshield wipers on a dry surface.

Do not clean with metal blades or scrapers.

10-30-4

S175 Service Manual

The LIFT & TILT VALVE light (Item 3) [Figure 10-30-6] will be ON when the door is closed and the PRESS TO OPERATE LOADER BUTTON is pressed.

•

TRANSPORTING LOADER ON A TRAILER

Fastening

Loading And Unloading

Figure 10-40-2

WARNING AVOID SERIOUS INJURY OR DEATH Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle. Wood ramps can break and cause personal injury.

W-2058-0807

P-73276

N-19048A

Be sure the transport and towing vehicles are of adequate size and capacity. (See Capacities on Page SPEC-10-4.)

Figure 10-40-1

Alternate Front Tie Down

P-24480b

P-31829B

1 P-31913A

A loader with an empty bucket or no attachment must be loaded backward onto the transport vehicle [Figure 1040-1].

Use the following procedure to fasten the Bobcat loader to the transport vehicle to prevent the loader from moving during sudden stops or when going up or down slopes [Figure 10-40-2].

•

Lower the bucket or attachment to the floor.

•

Stop the engine.

•

Engage the parking brake.

•

Install chains at the front and rear loader tie down positions (Inset) [Figure 10-40-2].

•

Fasten each end of the chain to the transport vehicle.

10-40-1

S175 Service Manual

The rear of the trailer must be blocked or supported (Item 1)[Figure 10-40-1] when loading or unloading the loader to prevent the front end of the trailer from raising up.

TOWING THE LOADER Procedure Because of the design of the loader, there is not a recommended towing procedure. •

The loader can be lifted onto a transport vehicle.

•

The loader can be skidded a short distance to move for service (EXAMPLE: Move onto a transport vehicle.) without damage to the hydrostatic system.

(The tires/tracks will not turn.) There might be slight wear to the tires/tracks when the loader is skidded.

The towing chain (or cable) must be rated at 1 & 1/2 times the weight of the loader (See Performance on Page SPEC-10-2.)

10-50-1

S175 Service Manual

Figure 10-60-2

REMOTE START TOOL KIT-MEL1563 Remote Start Tool - MEL1563 Tools that will be needed to complete the following steps are:

2 MEL1563 - Remote Start Tool MEL1565 - Service Tool Harness Control MEL1566 - Service Tool Harness Communicator (Computer Interface)

3

1

Figure 10-60-1

P16117

1

The traction lock switch (Item 1) [Figure 10-60-2] is used to turn traction lock ON or OFF. Push the switch to the override postion. The switch will illuminate to indicate traction lock OVERRIDE, in this position the wheels are able to turn.

P16114

The remote start tool (Item 1) [Figure 10-60-1] is required when the service technician is checking the hydraulic/hydrostatic system or adjusting the steering linkage.

The maximum flow/variable flow switch (Item 2) [Figure 10-60-2] is used to activate the auxiliary hydraulics.

Pressing the switch once will activate maximum flow.

Pressing the switch again will activate variable flow. The switch will illuminate to indicate which flow rate is active.

Pressing the switch a third time will turn the flow OFF. The switch is used when checking pressures and flow rate.

The auxiliary pressure release (Item 3) [Figure 10-60-2] is used to release hydraulic pressure to the front and/or rear auxiliary couplers. To release pressure; push and hold the switch for a few seconds.

NOTE: With the engine running; pushing and holding the pressure release switch will cause the engine to stop. To relieve the pressure; press the switch until the engine stops.

10-60-1

S175 Service Manual

REMOTE START TOOL-MEL1563 (CONT'D)

Service Tool Harness Control - MEL1565

Remote Start Tool - MEL1563 (Cont’d)

Figure 10-60-5

Figure 10-60-3

2

1

1

P16114 P16116

The service tool harness control (Item 1) [Figure 10-605] is used to connect the remote start tool (Item 2) [Figure 10-60-5] to the electrical system on the loader.

Figure 10-60-4

Figure 10-60-6

1

1

P16120

The 10-pin rectangular connector (Item 1) [Figure 10-603] is used to update software in the Deluxe Instrumentation Panel (Item 1) [Figure 10-60-4].

NOTE: The Service PC must be connected to the remote start tool to update the deluxe panel software.

N-19561

Remove the plug (Item 1) [Figure 10-60-6] from the loader harness connector.

Connect the service tool harness control to the loader harness connector.

The panel must be removed from inside the operator cab and plugged into this connector [Figure 10-60-3].

10-60-2

S175 Service Manual

REMOTE START TOOL-MEL1563 (CONT'D)

Service Tool Harness Communicator - MEL1566

Service Tool Harness Control - MEL1565 (Cont’d)

Figure 10-60-8

Figure 10-60-7

2

2 1

1 P16119 N-19631

Loaders equipped with an attachment harness (Item 1) [Figure 10-60-7] must disconnect the attachment harness from the loader harness (Item 2) [Figure 10-607].

The service tool harness communicator (Item 1) [Figure 10-60-8] is required to connect remote start tool to the Service PC (Item 2) [Figure 10-60-8].

Connect the service tool harness to the ACD connector and the loader harness connector.

NOTE: To monitor, diagnose or load new software the Service PC must be connected to the Remote Start Tool Switch.

10-60-3

S175 Service Manual

Figure 10-60-11

REMOTE START TOOL KIT-MEL1563 (CONT’D) Remote Start Procedure The tool listed will be needed to do the following procedure: MEL1563: Remote Start Tool Kit

1

Figure 10-60-9

1 N-19150

Remove the plug (Item 1) [Figure 10-60-10] or disconnect the attachment control harness (Item 1) [Figure 10-60-11] if connected.

Figure 10-60-12

P16115

The remote start tool (Item 1) [Figure 10-60-9] is required when the operator cab is in the raised position for service and the service technician needs to turn the key switch on or start the engine. Example: adjusting the steering linkage.

Lift and block the loader. (See LIFTING AND BLOCKING THE LOADER on Page 10-10-1.)

Raise the lift arms (if required by the procedure) and install an approved lift arm support device. (See LIFT ARM SUPPORT DEVICE on Page 10-10-1.)

P13861

Raise the operator cab (if required by the procedure).

(See Raising on Page 10-10-2.)

Connect the remote start tool to the engine harness connector [Figure 10-60-12].

Open the rear door of the loader.

NOTE: The key switch on the right-hand side operator panel must be in the off position or the Remote Start Kit will not operate.

Figure 10-60-10

WARNING AVOID INJURY OR DEATH With the 7-pin connector plugged into the loader and the Remote Start Key Switch in the OFF position, the loader can still be started from the operator panel inside the cab. Placing the key switch of the remote start tool in the run position disconnects the operator panel key switch from the start circuit. If the service technician will be working in the engine area it is important to remove the operator panel keys.

1

W-2357-0899

N-19151

10-60-4

S175 Service Manual

Figure 10-60-14

REMOTE START TOOL KIT-MEL1563 (CONT'D) Remote Start Procedure (Cont'd) Figure 10-60-13

2 3

1

1

P16118

P16116

The remote start tool (Item 1) [Figure 10-60-13] has three rocker switches.

The traction lock switch (Item 1) [Figure 10-60-14] is used to turn traction lock on or off. Push the switch to the override position. The switch will illuminate to indicate traction lock OVERRIDE, in this position the wheels are able to turn.

The maximum flow/variable flow switch (Item 2) [Figure 10-60-14] is used to activate the auxiliary hydraulics.

Pressing the switch once will activate variable flow.

Pressing the switch again will activate maximum flow.

The switch will illuminate to indicate which flow rate is active. Pressing the switch a third time will turn the flow OFF. The switch is used when checking pressures and flow rate.

The auxiliary pressure release (Item 3) [Figure 10-60-14] is used to release hydraulic pressure to the front and/or rear auxiliary couplers. To release pressure; push and hold the switch for three seconds.

NOTE: With the engine running; pushing and holding the pressure release switch will cause the engine to stop in three seconds. To relieve the pressure; continue to press the switch after the engine has stopped.

10-60-5

S175 Service Manual

REMOTE START TOOL KIT-MEL1563 (CONT'D) Remote Start Procedure (Cont'd) NOTE: With the engine running; pushing and holding the pressure release switch will cause the engine to stop in three seconds. To relieve the pressure at the rear or right hand auxiliary, (If so equipped.) continue to hold the switch for three seconds after the engine has stopped.

Figure 10-60-15

P-34661

Push the couplers on the front auxiliary block toward the block and hold for five seconds to release the front auxiliary pressure [Figure 10-60-15].

10-60-6

S175 Service Manual

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 Description The Remote Start Tool (Service Tool) Kit is a replacement tool for MEL 1563 Remote Start Tool and MEL 1400B BOSS® Diagnostic Tool.

The Remote Start Tool (Service Tool) Kit, P/N 6689779, can be used to service older loaders with the BOSS® system using the supplied BOSS® Service Tool Harness P/N 6689745.

The Remote Start Tool (Service Tool) Kit, P/N 6689779, can be used to service newer loaders using the supplied harness P/N 6689747.

A computer can be connected to the Remote Start Tool (Service Tool) for diagnostics and software updates using the computer harness P/N 6689746 in conjunction with the loader harness.

10-61-1

S175 Service Manual

Figure 10-61-17

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D)

2

Remote Start Tool (Service Tool) - 6689778 Tools that will be needed to complete the following steps are:

5

3

Order from Bobcat Parts P/N: 6689779 - Remote Start Tool (Service Tool) Kit

6

4

Kit Includes: 6689778 - Remote Start Tool (Service Tool) 6689747 - Loader Service Tool Harness 6689746 - Computer Service Tool Harness 6689745 - BOSSÂŽ Service Tool Harness

1

P-76439

Figure 10-61-16 The Remote Start Tool (Service Tool) (Item 1) [Figure 1061-17] has five buttons.

The STOP button (Item 2) [Figure 10-61-17] is used to stop the Remote Start Tool (Service Tool) from communicating and stop the loader engine.

The RUN button (Item 3) [Figure 10-61-17] is used to turn the Remote Start Tool (Service Tool) on and activates the loader ignition power. The button will illuminate to indicate the service tool is active.

1

The START button (Item 4) [Figure 10-61-17] is used to start the loader engine.

P-76678

The remote start tool (Item 1) [Figure 10-61-16] is required when the service technician is checking the hydraulic / hydrostatic system or adjusting the steering linkage.

The traction lock button (Item 5) [Figure 10-61-17] is used to turn traction lock ON or OFF. Push the button and the button will illuminate indicating the traction lock is disabled in which the wheels or tracks are able to turn.

The auxiliary button (Item 6) [Figure 10-61-17] is used to activate the auxiliary hydraulics. The button will illuminate to indicate the auxiliary hydraulics are active. Pressing the button once will activate variable flow. Pressing the button again will activate maximum flow. Pressing the button a third time will turn the flow OFF. The button is used when checking pressures and flow rate.

10-61-2

S175 Service Manual

Figure 10-61-20

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D) Loader Service Tool Harness - 6689747

2

Figure 10-61-18

1 1

P-76452

2

Loaders with an attachment control harness (7 pin or 14 pin), the attachment harness (Item 1) must be disconnected from the loader harness (Item 2) [Figure 10-61-20].

P-76678

The loader service tool harness (Item 1) [Figure 10-6118] is used to connect the remote start tool (service tool) (Item 2) [Figure 10-61-18] to the electrical system on the loader.

When the remote start procedure is completed, replace the loader connector cap (Item 1) [Figure 10-61-19] or reconnect the attachment control harness to the loader harness [Figure 10-61-20].

Figure 10-61-19

1

P-76451

Loaders without an attachment control harness, remove the loader harness cap (Item 1) [Figure 10-61-19] and connect the Loader Service Tool Harness from the Remote Start Tool (Service Tool).

10-61-3

S175 Service Manual

Computer Service Tool Harness - 6689746

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D)

Figure 10-61-22

Loader Service Tool Harness - 6689747 (Cont’d) Figure 10-61-21 2

1 1

2

3

P-76450

1 P-76453

NOTE: The Remote Start Tool (Service Tool) connection harness has two connectors (Item 1) and (Item 3). The main connector (Item 1) [Figure 10-61-21] is always used for connection to the loader harness.

The computer service tool harness (Item 1) [Figure 1061-22] is required to connect remote start tool (service tool) to the Service PC (Item 2) [Figure 10-61-22].

The second connector (Item 3) [Figure 10-6121] is used for attachment ACD upgrades or attachment operational diagnostics only. This connector has a cap attached to it to prevent damage or corrosion when not in use.

Connect the Remote Start Tool (Service Tool) connector (Item 1) to the loader harness connector (Item 2) and the other Remote Start Tool (Service Tool) connector to the ACD harness connector (Item 3) [Figure 10-61-21].

NOTE: The right instrument panel (Key Switch or Keyless) must be in the off position or the Remote Start Tool (Service Tool) will not operate.

P-76454

10-61-4

S175 Service Manual

Figure 10-61-24

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D) Remote Start Procedure

1

WARNING AVOID INJURY OR DEATH With the 7-pin connector plugged into the loader and Remote Start Tool RUN button is not illuminated, the loader can still be started from the operator panel inside the cab.

Pressing the RUN button on the Remote Start Tool disconnects the operator panel from the start circuit.

If the service technician will be working in the engine area it is important to remove the operator panel key or lock the keypad with a unique password.

W-2647-0707

The tool listed will be needed to do the following procedure:

P-76451

Loaders without an attachment control harness, remove the loader harness cap (Item 1) [Figure 10-61-24] and connect the Loader Service Tool Harness from the Remote Start Tool (Service Tool).

Figure 10-61-25 2

6689779: Remote Start Tool (Service Tool) Kit Figure 10-61-23

1 1

P-76452

Loaders with an attachment control harness (7 pin or 14 pin), the attachment harness (Item 1) must be disconnected from the loader harness (Item 2) [Figure 10-61-25].

P-76450

The Remote Start Tool (Service Tool) (Item 1) [Figure 1061-23] is required when the operator cab is in the raised position for service and the service technician needs to turn on the loader or start the engine. Example: adjusting the steering linkage.

When the remote start procedure is completed, replace the loader connector cap (Item 1) [Figure 10-61-25] or reconnect the attachment control harness to the loader harness [Figure 10-61-25].

Lift and block the loader.

Raise the lift arms (if required by the procedure) and install an approved lift arm support device.

Raise the operator cab (if required by the procedure).

Open the rear door of the loader.

10-61-5

S175 Service Manual

Figure 10-61-27

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D)

2

Remote Start Procedure (Cont'd) Figure 10-61-26

5

3

6

4

2 1 1

P-76439

3 1

The Remote Start Tool (Service Tool) (Item 1) [Figure 1061-27] has five buttons.

P-76453

NOTE: The Remote Start Tool (Service Tool) connection harness has two connectors (Item 1) and (Item 3). The main connector (Item 1) [Figure 10-61-26] is always used for connection to the loader harness.

The second connector (Item 3) [Figure 10-6126] is used for attachment ACD upgrades or attachment operational diagnostics only. This connector has a cap attached to it to prevent damage or corrosion when not in use.

Connect the Remote Start Tool (Service Tool) connector (Item 1) to the loader harness connector (Item 2) and the other Remote Start Tool (Service Tool) connector to the ACD harness connector (Item 3) [Figure 10-61-26].

NOTE: The right instrument panel (Key Switch or Keyless) must be in the off position or the Remote Start Tool (Service Tool) will not operate.

The STOP button (Item 2) [Figure 10-61-27] is used to stop the Remote Start Tool (Service Tool) from communicating and stop the loader engine.

The RUN button (Item 3) [Figure 10-61-27] is used to turn the Remote Start Tool (Service Tool) on and activates the loader ignition power. The button will illuminate to indicate the service tool is active.

The START button (Item 4) [Figure 10-61-27] is used to start the loader engine.

The traction lock button (Item 5) [Figure 10-61-27] is used to turn traction lock ON or OFF. Push the button and the button will illuminate indicating the traction lock is disabled in which the wheels or tracks are able to turn.

The auxiliary button (Item 6) [Figure 10-61-27] is used to activate the auxiliary hydraulics. The button will illuminate to indicate the auxiliary hydraulics are active. Pressing the button once will activate variable flow. Pressing the button again will activate maximum flow. Pressing the button a third time will turn the flow OFF. The button is used when checking pressures and flow rate.

P-76454

10-61-6

S175 Service Manual

Figure 10-61-29

REMOTE START TOOL (SERVICE TOOL) KIT 6689779 (CONT'D) Remote Start Procedure (Cont'd) Figure 10-61-28

1

2 P-34661

Push the couplers on the front auxiliary block toward the block and hold for five seconds to release the front auxiliary pressure [Figure 10-61-29].

P-76441

The gear icon with the left facing arrows (Item 1) [Figure 10-61-28] will illuminate and blink when the RUN key is pressed and the loader is communicating with the service tool.

The computer icon with the right facing arrows (Item 2) [Figure 10-61-28] will illuminate and blink when the Remote Start Tool (Service Tool) is transmitting data to and from the computer.

NOTE: To relieve the pressure at the rear or secondary front auxiliary, (if equipped) press and hold the AUXILIARY PRESSURE RELEASE button on the left instrument panel for three seconds after the engine has stopped.

10-61-7

S175 Service Manual

SERVICE SCHEDULE Chart Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Bobcat Loader.

WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0903

SERVICE SCHEDULE ITEM Engine Oil Engine Air Filter and Air System Engine Cooling System Fuel Filter Lift Arms, Cylinders, Bob-Tach Pivot Pins and Wedges Tires

SERVICE REQUIRED

HOURS 8-10

50

100

■

■

■

250

500

1000

Check the oil level and add as needed. Do not overfill.

Check display panel. Service only when required. Check for leaks and damaged components.

Clean debris from oil cooler, radiator and grill. Check coolant level COLD and add premixed coolant as needed.

Remove the trapped water.

Lubricate with multi-purpose lithium based grease.

Check for damaged tires and correct air pressure. Inflate to MAXIMUM pressure shown on the sidewall of the tire.

Seat Bar, Control Interlocks, Seat Check the condition of seat belt. Clean or replace seat belt retractors as Belt, Seat Belt Retractors needed. Check the seat bar and control interlocks for correct operation. Clean dirt and debris from moving parts.

Bobcat Interlock Control Systems Check for correct function. Lift and Tilt functions MUST NOT operate with seat (BICS) bar raised. See details in this Manual.

Safety Signs and Safety Treads Check for damaged signs (decals) and safety treads. Replace any signs or safety treads that are damaged or worn.

Operator Cab Check the fastening bolts, washers and nuts. Check the condition of the cab.

Indicators and Lights Check for correct operation of all indicators and lights.

Heater and A/C Filters Clean or replace filters as needed.

(If Equipped) Hydraulic Fluid, Hoses and Check fluid level and add as needed. Check for damage and leaks. Repair or Tubelines replace as needed.

Final Drive Trans. (Chaincase), Check fluid level and add as needed.

Parking Brake, Foot Pedals, Check for correct operation. Repair or adjust as needed.

Hand Controls and Steering Levers or Joysticks Wheel Nuts Check for loose wheel nuts and tighten to correct torque. (See TIRE MAINTENANCE in this manual.)

Spark Arrestor Muffler Clean the spark chamber.

Battery Check cables, connections and electrolyte level. Add distilled water as needed.

Steering Lever Pivots Grease fittings.

Fuel Filter Replace filter element.

Engine / Hydro. Drive Belt Check for wear or damage. Check idler arm stop.

Drive Belts (Alternator, air Check condition and tension. Adjust or replace as needed. conditioner, water pump) Bobcat Interlock Control System Check the function of the lift arm bypass control.

(BICS) Engine Oil and Filter Replace oil and filter.

Hydraulic / Hydrostatic Filter, Replace the hydraulic / hydrostatic filter, charge filter, and the reservoir Charge Filter, Reservoir Breather breather.

Final Drive Trans. (Chaincase) Replace the fluid.

Hydraulic Reservoir Replace the fluid.

Case Drain Filters Replace the filters.

Engine Valves Adjust the engine valves.

Coolant Replace the coolant

❏

▲

▲

✶

●

▲ ❍ Every 2 years

■

Or every 12 months.

▲ ❏ ● ✶

Perform at first 50 hours, then as scheduled.

Check every 8 - 10 hours for the first 24 hours, then at 50 hour intervals.

Replace the hydraulic / hydrostatic filter element after the first 50 hours, then when the transmission warning light comes ON while operating or as scheduled.

Change oil and filter every 100 hours when operating under severe conditions.

❍

Perform at first 500 hours, then as scheduled.

10-70-1

S175 Service Manual

AIR CLEANER SERVICE

Outer Filter

Replacing Filter Elements

Figure 10-80-3

Figure 10-80-1 1 1 1

P-76732 B-15552B

B-15553B

It is important to change the air filter element only when the Air Cleaner Icon in the right panel is ON (Item 1) [Figure 10-80-1] and you hear three beeps from the alarm.

Remove the wing nut (Item 1) [Figure 10-80-3] and remove the dust cover .

Figure 10-80-4

Replace the inner filter every third time the outer filter is replaced or as indicated.

1

Figure 10-80-2

2 P-76730

1

Remove the wing nut and remove the outer filter element (Item 1) [Figure 10-80-4].

NOTE: Make sure all sealing surfaces are free of dirt and debris. Do not use air pressure to clean.

B-15551

Press and hold the LIGHT Button (Item 1) [Figure 10-802] for two seconds.

Install a new outer element.

Install the dust cover and the wing nut [Figure 10-80-3].

If the filter element needs replacement, the CODE [0117] (Air Filter Plugged) will show in the HOURMETER / CODE DISPLAY (Item 2) [Figure 10-80-2].

Check the air intake hose and the air cleaner housing for damage. Make sure all connections are tight.

10-80-1

S175 Service Manual

Figure 10-80-6

AIR CLEANER SERVICE (CONT’D) Replacing Filter Elements (Cont’d) Inner Filter Only replace the inner filter element under the following conditions: •

Replace the inner filter element every third time the outer filter is replaced.

•

After the outer element has been replaced, start the engine and run at full RPM. If the HOURMETER / CODE DISPLAY shows [01-17] (Air Filter Plugged), replace the inner filter element.

1

P-76732

Figure 10-80-5 Install the dust cover and the wing nut [Figure 10-80-6].

1

P-76731

Remove the wing nut and remove the inner filter element (Item 1) [Figure 10-80-5].

NOTE: Make sure all sealing surfaces are free of dirt and debris.

Install the new inner element.

Install the outer element.

10-80-2

S175 Service Manual

Figure 10-90-2

ENGINE COOLING SYSTEM Check the cooling system every day to prevent overheating, loss of performance or engine damage.

1

WARNING AVOID INJURY OR DEATH Wear safety glasses to prevent eye injury when any of the following conditions exist: • When fluids are under pressure.

• Flying debris or loose material is present.

• Engine is running.

• Tools are being used.

P-34113

W-2019-0907

Cleaning Open the rear door and remove the rear grill. (See REAR GRILL on Page 50-60-1.)

NOTE: All access covers (Item 1) [Figure 10-90-2] (both sides) must be in place to ensure correct air flow through the oil cooler which will ensure cooling for engine and hydraulic system.

Figure 10-90-1

1

P-45101

Use low air pressure or water pressure to clean the top of the oil cooler (Item 1) [Figure 10-90-1].

NOTE: Be careful when raising and lowering the oil cooler so that the oil cooler does not fall on the radiator and damage the fins.

Raise the oil cooler and use low air pressure or water pressure to clean the top of the radiator.

Lower the oil cooler.

Check the cooling system for leaks.

Lower the rear grill and close the rear door.

10-90-1

S175 Service Manual

ENGINE COOLING SYSTEM (CONT’D) Checking Level

IMPORTANT

Open the rear door and raise the rear grill.

AVOID ENGINE DAMAGE Always use the correct ratio of water to antifreeze.

Figure 10-90-3

Too much antifreeze reduces cooling system efficiency and may cause serious premature engine damage.

Too little antifreeze reduces the additives which protect the internal engine components; reduces the boiling point and freeze protection of the system.

1 3

Always add a premixed solution. Adding full strength concentrated coolant can cause serious premature engine damage.

2

I-2124-0497 P-54299

P-76738

Add premixed coolant, 47% water and 53% propylene glycol to the recovery tank. See Checking Level.

Check coolant level. The level markers are on the tank (Item 2) [Figure 10-90-3]. Coolant must be at the bottom marker when the engine is cold; top marker when hot.

One gallon and one pint (4,3 L) of propylene glycol mixed with one gallon (3,8 L) of water is the correct mixture of coolant to provide a -34°F (-37°C) freeze protection.

Close the rear door before operating the loader.

Fill the tank until it is at the lower marker on the tank and replace the coolant fill cap.

Removing And Replacing Coolant

NOTE: When installing the coolant fill cap, the cap must be tightened until it clicks.

Open the rear door and remove the rear grill.

Remove the coolant fill cap (Item 1) [Figure 10-90-3].

Attach a hose to the coolant drain petcock (Item 3) [Figure 10-90-3] located above the fuel filter. Open the petcock and drain the coolant into a container. Recycle or dispose of coolant in an environmentally safe manner.

Run the engine until it is at operating temperature. Stop the engine. Check the coolant level when cool. Use a refractometer to check the condition of propylene glycol in your cooling system. Add coolant as needed.

Install the rear grill and close the rear door.

Close the coolant drain petcock.

Mix new coolant in a separate container. (See Capacities on Page SPEC-10-4.)

NOTE: The loader is factory filled with propylene glycol coolant (purple color). DO NOT mix propylene glycol with ethylene glycol.

10-90-2

S175 Service Manual

FUEL SYSTEM

Biodiesel Blend Fuel

Fuel Specifications

Biodiesel blend fuel has unique qualities that should be considered before using in this machine:

Use only clean, high quality diesel fuel, Grade No. 2 or Grade No. 1.

•

Cold weather conditions can lead to plugged fuel system components and hard starting.

The following is one suggested blending guideline which should prevent fuel gelling during cold temperatures:

•

Biodiesel blend fuel is an excellent medium for microbial growth and contamination which can cause corrosion and plugging of fuel system components.

•

Use of biodiesel blend fuel may result in premature failure of fuel system components, such as plugged fuel filters and deteriorated fuel lines.

•

Shorter maintenance intervals may be required, such as cleaning the fuel system and replacing fuel filters and fuel lines.

•

Using biodiesel blended fuels containing more than five percent biodiesel can affect engine life and cause deterioration of hoses, tubelines, injectors, injector pump and seals.

TEMPERATURE F° (C°)

NO. 2

NO. 1

+15°(9°)

100%

0%

Down to -20° (-29°)

50%

50%

Below -20° (-29°)

0%

100%

At a minimum, Low Sulfur (500 ppm sulfur) Diesel Fuel must be used in this machine.

The following fuels may also be used in this machine: •

Ultra Low Sulfur (15 ppm sulfur) Diesel Fuel.

•

Biodiesel Blend Fuel - Must contain no more than five percent biodiesel mixed with low sulfur or ultra low sulfur petroleum based diesel. This is commonly marketed as B5 blended diesel fuel. B5 blended diesel fuel must meet ASTM D975 (US Standard) or EN590 (EU Standard) specifications.

Apply the following guidelines if biodiesel blend fuel is used: •

Ensure the fuel tank is as full as possible at all times to prevent moisture from collecting in the fuel tank.

•

Ensure that the fuel tank cap is securely tightened.

•

Biodiesel blend fuel can damage painted surfaces, remove all spilled fuel from painted surfaces immediately.

•

Drain all water from the fuel filter daily before operating the machine.

•

Do not exceed engine oil change interval. Extended oil change intervals can cause engine damage.

•

Before vehicle storage; drain the fuel tank, refill with 100% petroleum diesel fuel, add fuel stabilizer and run the engine for at least 30 minutes.

NOTE: Biodiesel blend fuel does not have long term stability and should not be stored for more than three months.

10-100-1

S175 Service Manual

Figure 10-100-2

FUEL SYSTEM (CONT’D)

WRONG

Filling the Fuel Tank

WARNING AVOID INJURY OR DEATH Stop and cool the engine before adding fuel. NO SMOKING! Failure to obey warnings can cause an explosion or fire.

W-2063-0807

Figure 10-100-1

B-15650

Use a clean, approved safety container to add fuel of the correct specifications. Add fuel only in an area that has free movement of air and no open flames or sparks. NO SMOKING! [Figure 10-100-2].

1

Install and tighten the fuel fill cap (Item 1) [Figure 10100-1].

WARNING P-76799

Open the rear door.

Remove the fuel fill cap (Item 1) [Figure 10-100-1].

AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

W-2103-0807

10-100-2

S175 Service Manual

FUEL SYSTEM (CONT’D)

Figure 10-100-4

Fuel Filter See the SERVICE SCHEDULE for the service interval for removing water from, or replacing the fuel filter. (See SERVICE SCHEDULE on Page 10-70-1.)

1

Removing Water Figure 10-100-3 2

3

P-76735

Open the vent (Item 3) [Figure 10-100-4] on the fuel filter housing.

Squeeze the hand pump (priming bulb) (Item 2) [Figure 10-100-4] until fuel flows from the vent with no air bubbles.

2 1 P-76734

Loosen the drain (Item 1) [Figure 10-100-3] at the bottom of the filter element to remove water from the filter.

Replacing Element

Close the vent (Item 3) [Figure 10-100-4] on the fuel filter housing.

Open the vent (Item 1) [Figure 10-100-4] on the fuel injection pump.

Squeeze the hand pump (priming bulb) (Item 2) [Figure 10-100-4] until the pump feels solid.

Remove the filter element (Item 2) [Figure 10-100-3].

Clean the area around the filter housing. Put clean oil on the seal of the new filter element. Install the fuel filter, and hand tighten.

Remove the air from the fuel system. (See Removing Air From The Fuel System below.)

Removing Air From The Fuel System After replacing the filter element or when the fuel tank has run out of fuel, the air must be removed from the fuel system before starting the engine.

Tighten the vent plug (Item 1) [Figure 10-100-4].

Start the engine.

It may be necessary to open the vent plug (Item 1) [Figure 10-100-4] briefly while the engine is running.

Close the vent when the engine runs smoothly.

WARNING AVOID INJURY OR DEATH Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or death. Fluid leaks under pressure may not be visible.

Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury.

W-2072-0807

10-100-3

S175 Service Manual

ENGINE LUBRICATION SYSTEM

Engine Oil Chart

Checking And Adding Engine Oil

Figure 10-110-2

Check the engine oil level every day before starting the engine for the work shift.

Figure 10-110-1

2

1 B-16320C P-76736

Open the rear door and remove the dipstick (Item 1) [Figure 10-110-1].

Use a good quality motor oil that meets API Service Classification of CI-4 or better See Oil Chart [Figure 10110-2].

Remove the oil fill cap (Item 2) [Figure 10-110-1] and add oil as necessary.

Keep the oil level between the marks on the dipstick. Do not overfill.

10-110-1

S175 Service Manual

ENGINE LUBRICATION SYSTEM (CONT’D)

WARNING

Removing And Replacing Oil And Filter See the SERVICE SCHEDULE for the service interval for replacing the engine oil and filter. (See SERVICE SCHEDULE on Page 10-70-1.)

Run the engine until it is at operating temperature. Stop the engine.

AVOID INJURY OR DEATH Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

W-2103-0807

Figure 10-110-3 2

3

P-24679

1 P-76737

Open the rear door and remove the drain hose (Item 1) [Figure 10-110-3]from its storage position.

Remove the drain hose cap (Item 2) [Figure 10-110-3] and drain the oil into a container. Recycle or dispose of used oil in an environmentally safe manner.

Remove the oil filter (Item 3) [Figure 10-110-3] and clean the filter housing surface.

Put clean oil on the new oil filter gasket, install new filter and hand tighten.

Install and tighten the drain hose cap. Return the drain hose to it’s storage position.

Remove the fill cap (Item 2) [Figure 10-110-1]. Put oil in the engine. For the correct quantity (See Capacities on Page SPEC-10-4.) Do not overfill.

Start the engine and let it run for several minutes. Stop the engine and check for leaks at the oil filter.

Remove the dipstick (Item 1) [Figure 10-110-1] and check the oil level.

Add oil as needed if it is not at the top mark on the dipstick. Install the dipstick and close the rear door.

10-110-2

S175 Service Manual

HYDRAULIC/HYDROSTATIC SYSTEM

Hydraulic / Hydrostatic Fluid Chart

Checking And Adding Fluid

Figure 10-120-2

Use only recommended fluid in the hydraulic system.

(See HYDRAULIC/HYDROSTATIC FLUID SPECIFICATIONS on Page SPEC-40-1.)

Stop the loader on a level surface.

Lower the lift arms and tilt the Bob-Tach fully back.

Stop the engine.

Figure 10-120-1

P-64023A

1 1

P-45224A P-45224A

Use the correct hydraulic / hydrostatic fluid shown in hydraulic / hydrostatic fluid chart [Figure 10-120-2].

2

P-48011

Check the fluid level in the sight gauge (Item 1) [Figure 10120-1].

Open the rear door and raise the rear grill. Remove the fill cap (Item 2) [Figure 10-120-1].

Add the fluid as needed to bring the level to the center of sight gauge (Item 1) [Figure 10-120-1].

Install the fill cap (Item 2) [Figure 10-120-1].

Lower the rear grill and close the rear door.

10-120-1

S175 Service Manual

Thank you very much for your reading.

Please Click Here Then Get More Information.