R&D FIXTURES
A Division of COYOD, LLC.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
b Sisertaying Green……………………………………………………………....……………………....……………......5 Cold Pan vs. Air Over Refrigeration……………………………………………………………....…………….......6 DROP IN COLD PANS Coppered Cold Pan……………………………………………………………....……………………........8 Air Over / Air Under Cold Pan………………………………....……………………....……………........11 REFRIGERATED UNITS Island Salad……………………………………………………………....……………………....…………….......14 Island End Station Options…………………………………..........…………....…....……………............18 Inline Salad……………………………………………………………....……………………....…………….......20 Inline Soup End Station…….......……………………………....……………………....……………........24 Inline Tray Recess………………………………………....……………………....……………................25 Island Refrigerated Merchandiser….............…………………....……………………....……………....................26 Olive……………………………………………………………....……………………....……………..................28 Mobile Olive.............................................................................................................................................................30 Grab-N-Go.............................................................................................……………....…………………...............33 Dual-Zone…………………………………………....……………………....…………….....................................36 Sandwich / Sushi / Pizza Case with Prep Counter....................................................................................................39 Mobile Low-Back ……………………………………………………………………………………………....…42 Mobile High-Back……………………………………………………………....…………………….……............45 SOUP BARS Island Round Soup………….............………………………………....……………………....……………...........48 Half Round Soup……………….............…………………………....……………………....……………..............51 End Cap Soup…………………….............……………………....……………………....……………...................52 HOT FOOD CASES Service Hot Food Line-Ups……………………….............…………………....……………………...…..............55 Service Heated Stone Line-Ups................................................................................................................................57 Island Hot Food…….............……………………………………....……………………....……………................59 Self-Serve Inline Hot Food…….............……………………………………....…………....……………..............62 Service Inline Hot Food…………................……………………....……………………....……………................65 Multi-Deck Merchandiser…………………………………………....……………………....…………….............68 Island Hot Food Merchandiser..................................................................................................................................71 Octagon Hot Food Merchandiser…………………………………………………….………….............................74 BAKERY CASES Inline Artisan Bread with Prep Counter....................................................................................................................77 Upright Artisan Bread – Low Profile………………………………………….…………………........…...............80 Upright Artisan Bread………………………………………………………………………….…....……..............83 Upright Pastry Case – Low Profile……………………………………………………………….....……..............86 Upright Pastry Case……………………………………………………………………………….....…..................89 EURO SERIES Service Candy / Chocolate…………………………………………………………….………………......92 Self-Serve Refrigerated…………………………………………….………………….………..…..……..95 Service Refrigerated……………………………………………….………………….……….…...……...98 Service Dry……………………………………………………….…………………….…….…...…..…101 Self-Serve Donut / Pastry………………………………….………………………….…….………....…104 POINT OF SALE MERCHANDISERS P.O.P Merchandiser................................................................................................................................................107 End Display.............................................................................................................................................................109 Cash Counters and Custom Modular Components.................................................................................................111 DISPLAY CASES Floral Displays........................................................................................................................................................113 Custom Millwork and Glass Display Cases............................................................................................................115 OPTIONS...…………………………………………………….………………………………….……....…......116 WARRANTY, TERMS & CONDITIONS………………......…………………………………………….......118
490 Industrial Drive Mt. Juliet, TN 37122 Ph: 888-827-6820 Fax: 615-758-1006 Email: sales@rdfixtures.com Website: www.rdfixtures.com
For over 20 years combined, R&D Fixtures has been designing and building equipment for supermarket and restaurant chains throughout the U.S and Canada. R&D Fixtures manufactures refrigerated cases, hot food cases, millwork, POP displays and various other cases for retail grocers and food service markets including national and international clients such as Albertson’s, A&P, AWG, Pro’s Ranch Markets, Schnucks, Shoprite, Sobey’s, SuperValu, Winn Dixie, Wegman’s, Whole Foods and more. R&D Fixtures prides itself for being known among the Supermarket Industry as a leading manufacturer of high-end quality fixtures with affordable prices and short lead times. Our experience of product knowledge combined with a talented innovative design and engineering department enables us to provide; a product you will be proud to own and enthusiastic to display. We at R & D Fixtures understand that without you, our customer, we could not continue to build what we live to do, create wonderful products and create lifelong relationships. Our customer service team is second to none. With a friendly and educated staff, we are happy to assist you in whatever your needs may be. We also understand that time is money, so we work closely with you to accommodate a quick response time to your needs. Whether remodeling or looking for cases to meet new design schemes, we are committed to providing the high quality products and customer service. Give us the opportunity to show you excellence and we guarantee your satisfaction. R&D Fixtures would like to thank you for your past support and we look forward to working with you in the near future. Sincerely,
D arlo Pack Darlo Pack Chief Executive Officer
Wiilliam C Wicks William C. Wicks Vice President of Sales
R&D
Staying Green
FIXTURES
A Division of COYOD, LLC.
onsumers are more aware of their impact on the C environment than ever before. According to a 2008
National survey, almost 62% of people would prefer to spend their money at an environmentally friendly business. R&D offers many environmentally friendly features. Some of the options available are: LED Lighting o 30% more energy efficient o 3 watt LEDs – currently the highest lumen output on the market o 500% longer life- lower maintenance & less waste o 100% glass and filament free o 100% mercury and toxic gas free Glycol Refrigeration o Available for remote refrigeration systems using organic compounds as alternatives to chemical refrigerant
Working on a LEED certification project?
Shallow Coppered Cold Pan o 39% more energy efficient (compared to an Air Over Cold Pan) o Requires 30% less BTUs Recycled Bumper o 100% recycled content o 100% recyclable o 100% free of PVC, Vinyl, Chlorine, and Bromine o 100% sustainable material o Exceeds the impact performance of PVC bumper by 30%
R&D Fixtures
Transportation within a 500 mile radius of our manufacturing facility to the location of installation can contribute to Rc5 - Regional Materials Credits, 1 to 2 points possible. Credit Intent Increase demand for building materials and products that are extracted and manufactured within the region, thereby supporting the use of indigenous resources and reducing the environmental impacts resulting from transportation.
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 5
R&D
Cold Pan vs. Air Over
FIXTURES
A Division of COYOD, LLC.
Coppered Cold Pan Technology R&D Fixtures’ exclusive cold pan technology salad bars are designed to meet all NSF-7 standards. The unit cuts down on cost by not moving air over the product. If you are accustomed to having air over, you know the product must be constantly stirred. Our unit is designed with copper tubing surrounding the entire cold pan, which eliminates the need to stir. The unit requires only 300 BTU’s per opening, compared to air over style that requires almost 650 BTU’s per pan. There are less moving parts to keep maintenance costs low. They are easy to clean and are designed to defrost automatically while still maintaining proper temperature. Cold Pan Technology keeps food from drying out and helps keep food fresher longer. Standard Units are Equipped With: • Warranty is one year parts and labor. • 18 gauge • NSF-7 listed • Perimeter pan drain • Thermostat • Automatic defrost to prevent ice build-up • Copeland Compressor
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 6
R&D
Cold Pan vs. Air Over
FIXTURES
A Division of COYOD, LLC.
Summary of Operating Costs $14,000 $12,000 $10,000 $8,000 $6,000 $4,000 $2,000 $-
Air Over Coppered Cold Pan
1st Qtr
2nd Qtr
3rd Qtr
4th Qtr
Air Over Cold Pan 208V * 43.4A = 9027.2W = 9.0272 KW 9.0272 KW * 24Hr = 216.6528 KW–Hr 216.6528 KW–Hr * $0.15/KW–Hr = $32.50 per 24 hour day = $11,862.50 per year (running 24 hours a day) Coppered Cold Pan 208V * 26.5A = 5512W = 5.512 KW 5.512 KW * 24Hr = 132.288 KW–Hr 132.288 KW–Hr * $0.15/KW–Hr = $19.84 per 24 hour day = $7,241.60 per year (running 24 hours a day) Yearly Savings $11,862.50 - $7,241.60 = $4,620.90 yearly savings *based on a rate of $0.15/KW–Hr running 24 hours a day, 365 days a year.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 7
R&D
Coppered Drop-In Cold Pan
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES CONSTRUCTION • Pan to consist of an 18 gauge stainless steel interior and 18 gauge galvanized underneath exterior. • Food pans and adapter bars rest on adjustable side rails so the food height can be changed from recessed 3” to flush. • Holds standard 4” deep, 12” x 20” inset pans or custom pans. • Full size pan adapter bars are included and allow for a variety of pan configurations. • Insulated with a polystyrene sheet, minimum 1” thick. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. REFRIGERATION SYSTEM • Product temperature to be between 38° and 40°F. • Cold pan wrapped on sides and bottom with refrigerated copper tubing. • Rated at 300 BTUs per full inset pan. • Energy efficient design means less compressor run-time and less indirect CO2 emissions. • Digital readout thermometer provided to verify product is maintained between 38° and 40°F. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup. • Standard refrigeration control supplied. • Ready for connection to condensing unit.
Copper Tubing
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 8
R&D
Coppered Drop-In Cold Pan
FIXTURES
A Division of COYOD, LLC.
Number of Wells (12x20) 2 3 4 5 6 7 8 9 10 11
R&D Fixtures
L 33-1/4 46-1/4 59-1/4 72-1/4 85-1/4 98-1/4 111-1/4 124-1/4 137-1/4 150-1/4
Dimensions (inches) W 27-1/4 27-1/4 27-1/4 27-1/4 27-1/4 27-1/4 27-1/4 27-1/4 27-1/4 27-1/4
H 9 9 9 9 9 9 9 9 9 9
BTUH @15ºF EVAP 600 900 1200 1500 1800 2100 2400 2700 3000 3300
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 9
R&D
Coppered Drop-In Cold Pan
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Pan to consist of an 18 gauge stainless steel interior and 18 gauge galvanized underneath exterior. • Cold pan wrapped on sides and bottom with refrigerated copper tubing. • Food pans and adapter bars rest on adjustable side rails so the food height can be changed from recessed 3” to flush. • Holds standard 4” deep, 12” x 20” inset pans or custom pans. • Units come standard with one set of divider bars. • Full size pan adapter bars are included and allow for a variety of pan configurations. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
Number of Wells (12x20) 2 3 4 5 6 7 8 9 10 11
Dimens ions (L x D x H) 33-1/4” x 27-1/4” x 9” 46-1/4” x 27-1/4” x 9” 59-1/4” x 27-1/4” x 9” 72-1/4” x 27-1/4” x 9” 85-1/4” x 27-1/4” x 9” 98-1/4” x 27-1/4” x 9” 111-1/4” x 27-1/4” x 9” 124-1/4” x 27-1/4” x 9” 137-1/4” x 27-1/4” x 9” 150-1/4” x 27-1/4” x 9”
L is t P rice $3,815 $3,877 $3,959 $4,070 $4,214 $4,297 $5,054 $6,058 $6,165 $6,173
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
Options
List Price
Adapter Bars Food Pans Refrigeration
1” Wide Not Included Remote
1/2” Wide Assorted Sizes Available Self-Contained
$21 Call for quote Call for quote
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 10
R&D
Air Over/Air Under Drop-In Cold Pan
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES CONSTRUCTION • Pan to consist of an 18 gauge stainless steel interior and 18 gauge galvanized underneath exterior. • Food pans and adapter bars rest on adjustable side rails so the food height can be changed. • Rails can be lowered 3” so air flow is over and under food product. • Rails can be raised with product flush so air flow is completely under. • Holds standard 4” deep, 12” x 20” inset pans. • Evaporator coil and fans are below the removable deck plates. • The fan housing is hinged for easy maintenance. • Full size pan adapter bars are included and allow for a variety of pan configurations. • Insulated with a polystyrene sheet, minimum 1” thick. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. REFRIGERATION SYSTEM • Product temperature to be between 38° and 40°F. • Rated at 650 BTUs per full inset pan. • Digital readout thermometer provided to verify product is maintained between 38º and 40ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup. • Standard refrigeration control supplied. • Ready for connection to condensing unit. • Available for glycol systems.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 11
R&D
Air Over/Air Under Drop-In Cold Pan
FIXTURES
A Division of COYOD, LLC.
Number of Wells (12x20) 2 3 4 5 6 7 8 9 10 11
R&D Fixtures
L 31 1/4 44 1/4 57 1/4 70 1/4 83 1/4 96 1/4 109 1/4 122 1/4 135 1/4 148 1/4
Dimensions (inches) W 28 1/4 28 1/4 28 1/4 28 1/4 28 1/4 28 1/4 28 1/4 28 1/4 28 1/4 28 1/4
H 14 5/16 14 5/16 14 5/16 14 5/16 14 5/16 14 5/16 14 5/16 14 5/16 14 5/16 14 5/16
BTUH @20º F EVAP 1300 1950 2600 3250 3900 4550 5200 5850 6500 7150
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 12
R&D
Air Over/Air Under Drop-In Cold Pan
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Pan to consist of an 18 gauge stainless steel interior and 18 gauge galvanized underneath exterior. • Food pans and adapter bars rest on adjustable side rails so the food height can be changed. • Rails can be lowered 3” so air flow is over and under food product. • Rails can be raised with product flush so air flow is completely under. • Holds standard 4” deep, 12” x 20” inset pans. • Evaporator coil and fans are below the removable deck plates. • Fan housing hinged for maintenance. • Full size pan adapter bars are included and allow for a variety of pan configurations. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor. Number of Wells (12x20) 2 3 4 5 6 7 8 9 10 11
Dimens ions (L x D x H) 31-1/4” x 28-1/4” x 14-5/16” 44-1/4” x 28-1/4” x 14-5/16” 57-1/4” x 28-1/4” x 14-5/16” 70-1/4” x 28-1/4” x 14-5/16” 83-1/4” x 28-1/4” x 14-5/16” 96-1/4” x 28-1/4” x 14 5/16” 109-1/4” x 28-1/4” x 14-5/16” 122-1/4” x 28-1/4” x 14-5/16” 135-1/4” x 28-1/4” x 14-5/16” 148-1/4” x 28-1/4” x 14-5/16”
L is t P rice
$4,009 $4,840 $5,309 $6,605 $7,309 $8,033 $8,766 $9,223 $9,815 $10,500
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications Adapter Bars Food Pans Refrigeration
R&D Fixtures
Standard
1” Wide Not Included Remote
Options
1/2” Wide Assorted Sizes Available Self-Contained
List Price
$21 Call for quote Call for quote
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 13
R&D
Island Salad
FIXTURES
A Division of COYOD, LLC.
Wood canopy with lift up glass and lower refrigerated storage*
Clear view canopy with fixed glass* *Optional features
SPECIFICATIONS / FEATURES BASE CABINET • Pan to consist of an 18 gauge stainless steel interior and 18 gauge galvanized underneath exterior. • Base of cabinet and counter top to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Fluorescent lights come with integral ballast, shatter shields, and a separate on/off switch. • Storage area below to house controls, electrical, and plumbing components. • Stainless steel corner protectors. • Protective 1” vinyl bumpers. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. REFRIGERATED COLD ZONES • NSF-7 refrigerated, coppered cold pan holds standard 4” deep, 12” x 20” inset pans. • Slopped feature angles food to increase visibility. • Remote refrigeration supplied with a standard refrigeration control. • Rated at 300 BTUs per full inset pan. • Adapter bars are included and allow for a variety of pan configurations. • Digital readout thermometer provided to verify temperature is maintained between 38 º and 40ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup. • Optional lower refrigerated storage has a blower coil with NSF certified coating, wire shelving, clear insulated sliding doors, incandescent lights, and a separate thermometer.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 14
R&D
Island Salad
FIXTURES
A Division of COYOD, LLC.
Island Salad 6' Island 8' Island 10' Island 12' Island 14' island
Number of Wells (12x20) 8 12 16 18 22
Dimensions (inches) L W H 72 66 57 1/2 96 66 57 1/2 120 66 57 1/2 144 66 57 1/2 168 66 57 1/2
Coppered Cold Pan BTUH @15º F Evap
Optional Lower Refrig. BTUH @15º F Evap
2400 3600 4800 5400 6600
n/a n/a 2000 2000 2200
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. • Amperage and voltage varies depending on the configuration. OPTIONS • Counter top available in stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. • Powder coated canopy assembly. • Canopy in clear view with fixed glass, and clear view with lift up glass. • Lower refrigerated storage. • Cold pan is available flat or sloped with either coppered or air over technology. • Bar packages can provide inset pans, lids, tongs, ladles, serving spoons, and salad dressing templates. • Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, cups/bowls, lids, and napkins. • Soup area featuring NSF-4 drop in kettles. • Recesses for takeout containers or trays. • Product enhancing lights. • Attractive recessed accent lighting around counter top. • Stainless or mirrored laminate accent strip. • Self contained refrigeration. • Base to be solid, adjustable legs, or legs with removable toe-kick. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 15
R&D
Island Salad
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (white, black or almond) optional colors available
• Standard wood canopy to consist of lift up tempered glass and fluorescent lighting. • Remote refrigeration, NSF-7 coppered Cold Pans wired to standard refrigeration control. • Standard adapter bars included. • Drain stub-out with gate valve. • 2 rows of protective vinyl bumper and corner guards. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, & NSF standards. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor. Model
6’
8’
10’
12’
14’
Dimensions 72” x 66” x 57-1/2” 96” x 66” x 57-1/2” 120” x 66” x 57-1/2” 144” x 66” x 57-1/2” 168” x 66” x 57-1/2” (L x D x H) Number of Wells 8 12 16 18 22 (12 X 20) Remote, Cold Pan $24,229 $27,576 $29,727 $33,144 $33,877 Refrigeration Self-Contained, Cold Pan $29,205 $32,118 $35,209 $38,746 $40,354 Refrigeration Remote, Air-Over $27,851 $30,777 $38,299 $41,638 $43,374 Refrigeration Self-Contained, Air-Over $33,444 $36,281 $44,667 $48,104 $53,081 Refrigeration Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 16
R&D
Island Salad Options
FIXTURES
A Division of COYOD, LLC.
3
1
4
2
5
Specifications
Options
Exterior 1
Other Finishes Available
Call for quote
Premium laminate colors Stainless Steel Corian CaesarStone Clear View with Fixed Glass Clear View with Lift Up Glass
Call for quote $2,070 $3,346 $4,610 $4,696
Counter Top 2
Canopy 3 Accent
Accent Down-Lighting Mirror laminate accent strip Stainless Steel accent strip
4
Electrical Connection Lower Refrigerated Storage 5 Warranty
R&D Fixtures
Circuit Breaker Panel Available for 10’, 12’, 14’ units Extended compressor warranty
6’-10’
12’-14’
Call for quote $9,124 $11,161 Call for quote $2,264 $2,680 $79 $464 $750 $2,675 Call for quote Call for quote
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 17
R&D
Island Salad Options
FIXTURES
A Division of COYOD, LLC.
Tray Recess and Soup End Station Options Dimensions: Add 2’ for each end station. Contact factory for assorted finishes, canopies, soup options, bar accessories and alternative configurations.
Tray Recess
R&D Fixtures
Soup Station
Rounded Soup Station
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 18
R&D
Island Salad Options
FIXTURES
A Division of COYOD, LLC.
Island Salad with Lift Up Clear View Canopy (End View)
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 19
R&D
Inline Salad
FIXTURES
A Division of COYOD, LLC.
Wood canopy with lift up glass.
Inline Salad with custom finish.
SPECIFICATIONS / FEATURES BASE CABINET • Pan to consist of an 18 gauge stainless steel interior and 18 gauge galvanized underneath exterior. • Base cabinet and counter top to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Fluorescent lights come with integral ballast, shatter shields, and a separate on/off switch. • Storage area below to house controls, electrical, and plumbing components. • Stainless steel corner protectors. • Protective 1” vinyl bumpers. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. REFRIGERATED COLD ZONES • NSF-7 refrigerated, coppered cold pan holds standard 4” deep, 12” x 20” inset pans. • Slopped feature angles food to increase visibility. • Remote refrigeration supplied with a standard refrigeration control. • Rated at 300 BTUs per full inset pan. • Adapter bars are included and allow for a variety of pan configurations. • Digital readout thermometer provided to verify temperature is maintained between 38º and 40ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup. • Optional lower refrigerated storage has a blower coil with NSF certified coating, wire shelving, clear insulated sliding doors, incandescent lights, and a separate thermometer.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 20
R&D
Inline Salad
FIXTURES
A Division of COYOD, LLC.
Inline Salad 6' Inline 8' Inline 10' Inline 12' Inline 14' Inline
Number of Wells (12x20) 4 6 8 9 11
Dimensions (inches) L W H 72 36 57 1/2 96 36 57 1/2 120 36 57 1/2 144 36 57 1/2 168 36 57 1/2
Coppered Cold Pan BTUH @15º F Evap
Optional Lower Refrig. BTUH @15º F Evap
1200 1800 2400 2700 3300
n/a n/a 1000 1200 1300
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NSF, NEC, and UL standards. • Amperage and voltage varies depending on the configuration. OPTIONS • Rear wall can be mirrored to enhance merchandising visibility. • Counter top available in stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. • Powder coated canopy assembly. • Canopy in clear view with fixed glass or clear view with lift up glass. • Lower refrigerated storage. • Cold pan is available flat or sloped with either coppered or air over technology. • Bar packages can provide inset pans, lids, tongs, ladles, serving spoons, and salad dressing templates. • Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, cups/bowls, lids, and napkins. • Soup area featuring NSF-4 drop in kettles. • Recesses for takeout containers or trays. • Product enhancing lights. • Attractive recessed accent lighting around counter top. • Stainless or mirrored laminate accent strip. • Self contained refrigeration. • Base to be solid, adjustable legs, or legs with removable toe-kick. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 21
R&D
Inline Salad
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (white, black or almond) optional colors available
• Standard wood canopy to consist of lift up tempered glass and fluorescent lighting • Remote refrigeration, NSF-7 coppered Cold Pans wired to standard refrigeration control • Standard adapter bars included • Drain stub-out with gate valve • 2 rows of protective vinyl bumper and corner guards • Chose front or rear doors when placing order. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, & NSF standards • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations • Warranty is one year parts and labor.
Model Dimensions (L x D x H) Number of Wells (12 X 20) Remote, Cold Pan Refrigeration SelfContained, Cold Pan Refrigeration Remote, Air-Over Refrigeration SelfContained, Air-Over Refrigeration
6’
8’
10’
12’
14’
72” x 36” x 57-1/2” 96” x 36” x 57-1/2” 120” x 36” x 57-1/2” 144” x 36” x 57-1/2” 168” x 36” x 57-1/2” 4
6
8
9
11
$15,268
$16,974
$19,617
$21,427
$23,290
$18,667
$20,264
$23,145
$25,969
$30,543
$17,936
$19,794
$23,550
$25,086
$29,108
$22,208
$25,383
$30,010
$31,899
$38,777
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 22
R&D
Inline Salad Options
FIXTURES
A Division of COYOD, LLC.
3
2
1
4 5
6
Specifications
Options
Exterior 1
Other Finishes Available
Call for quote
Premium laminate colors Stainless Steel Corian CaesarStone Clear View with Fixed Glass Clear View with Lift Up Glass Accent Down-Lighting Mirror laminate accent strip Stainless Steel accent strip
Call for quote $1,535 $2,350 $2,906 $4,156 Call for quote $6,461 $9,219 Call for quote $905 $1,214 $79 $235 $400 $877 $1,560 $2,675 Chose when ordering Call for quote Call for quote
Counter Top 2 Canopy 3 Accent 4 Rear Wall 5 Electrical Connection Doors 6 Lower Refrigerated Storage 6 Warranty
R&D Fixtures
6’-10’
Mirrored Rear Wall Circuit Breaker Panel Front or Back Available for 10’, 12’, 14’ units Extended compressor warranty
12’-14’
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 23
R&D
Inline Soup End Station
FIXTURES
Designed to fit Hot or Cold Inline Cases
A Division of COYOD, LLC.
STANDARD FEATURES Base of cabinet and counter top finished with high pressure plastic laminate (white, black, or almond) optional colors available
2 rows of protective vinyl bumper and corner guards. Standard wood canopy to consist of fluorescent lighting.
Units come with soup inserts, lids, ladles, 2 cup dispensers, 2 napkin dispensers, and 2 Bain Maries. 3 rows of protective vinyl bumper and corner guards. Optional rear or front doors. Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. Contact factory for assorted finishes and alternative configurations. Built in accordance with NEC, UL, and NSF standards. Warranty is one year parts and labor.
optional tempered glass
Description
2 Soup Wells
3 Soup Wells
4 Soup Wells
Dimensions (L x D x H)
45”x36”x57-1/2”
60”x36”x57-1/2”
75”x36”x57-1/2”
Warmers (7qt or 11qt)
$12,520
$13,542
$15,484
Cook-N-Hold (11qt only)
$15,766
$18,415
$21,977
2 Soup Wells
Specifications
Options
Exterior
Other Finishes Available Premium Laminate Colors Caesarstone Stainless Steel Corian Canopy with Glass Clear View Canopy Front or Back Mirror laminate accent strip Stainless Steel accent strip Mirrored Rear Wall
Counter Top
Canopy Doors Accent Rear Wall
3 Soup Wells Call for quote
4 Soup Wells
Call for quote $2,284 $3,209 $1,577 Call for quote Choose when ordering $79 $400 $877
End stations are available without sneeze guards. Required in some jurisdictions. Check with your local health department.
Shown with Tray Recess and Soup Station
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 Fax (615) 758-1006
www.rdfixtures.com
sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 24
R&D
Inline Tray Recess Station Designed to fit Hot or Cold Inline Cases
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base of cabinet and counter top finished with high pressure plastic laminate (white, black, or almond) optional colors available
• • •
2 rows of protective vinyl bumper and corner guards. Contact factory for assorted finishes and alternative configurations. Warranty is one year parts and labor.
Inline Salad with Tray Recess
Model
2’
3’
4’
Dimensions
24”x36”x36”
36”x36”x36”
48”x36”x36”
List Price
$1,740
$1,768
$1,806
(L x D x H)
Specifications
Options
2’
Exterior
Other Finishes Available
Counter Top
Premium Laminate Colors Caesarstone Stainless Steel Corian
3’
4’
Call for quote Call for quote $861 $972
$963 $1,210
$963 $1,445
End station is available with sneeze guard. Required in some jurisdictions. Check with your local health department.
Shown with Tray Recess and Soup Station
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 25
R&D
Island Refrigerated Merchandiser
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET • Unit built with 14 gauge steel frame and finished with high pressure plastic laminate exterior. • Lights come with integral ballast, shatter shields, and a separate on/off switch. • Three-tier style for displaying “Ready to Eat” products. • Curved window end panels. • Storage area below to house controls, electrical, and plumbing components. • Stainless steel product stops. • Protective 1” vinyl bumpers. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor.
REFRIGERATION • Remote refrigeration supplied with a standard refrigeration control. • Digital readout thermometer provided to verify temperature is maintained between 38º and 40ºF. • Condensate evaporation pan is available to eliminate the need for plumbing hookup.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 26
R&D
Island Refrigerated Merchandiser
FIXTURES
A Division of COYOD, LLC.
1 1
L
Dimensions (inches) W
H
78
78
55
Model Island Refrigerated Merchandiser
BTUH @20º F EVAP 1300
Product Specifications
Standard
Options
List Price
Exterior Refrigeration Refrigeration
White, Black, Almond Laminate Remote Remote
Other Finishes Available Remote Self-Contained
Call for quote $29,336 $36,188
1
ELECTRICAL REQUIREMENTS • Unit is pre-wired to 120V/208A plug, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NSF, NEC, and UL standards. • Amperage and voltage varies depending on the configuration. OPTIONS • Assorted colors available for laminate, vinyl bumper, and powder coat. • Powder coated canopy assembly. • Product enhancing lights. • Attractive recessed accent lighting around counter top. • Stainless or mirrored laminate accent strip. • Self contained refrigeration. • Electric condensate pan. • Base to be solid, adjustable legs, or legs with removable toe-kick. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 27
R&D
Olive
FIXTURES
A Division of COYOD, LLC.
Island Olive
Inline Olive
SPECIFICATIONS / FEATURES BASE CABINET • Pan to consist of an 18 gauge stainless steel interior and 18 gauge galvanized underneath exterior. • Base cabinet and counter top to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Fluorescent lights come with integral ballast, shatter shields, and a separate on/off switch. • Storage area below to house controls, electrical, and plumbing components. • Stainless steel corner protectors. • Protective 1” vinyl bumpers. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. REFRIGERATED COLD ZONES • NSF-7 refrigerated, coppered cold pan holds standard 4” deep, 12” x 20” inset pans. • Custom inset pans available which sit flush on adjustable rails and eliminate flange between pans to give the look of continuous food. • Remote refrigeration supplied with a standard refrigeration control. • Rated at 300 BTUs per full inset pan. • Adapter bars are included and allow for a variety of pan configurations. • Digital readout thermometer provided to verify temperature is maintained between 38º and 40ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 28
R&D
Olive
FIXTURES
A Division of COYOD, LLC.
Olive 6' Island 8' Island 10' Island 12' Island 14' island 6' Inline 8' Inline 10' Inline 12' Inline 14' Inline
Number of Wells (12x20) 8 12 16 18 22 4 6 8 9 11
L 72 96 120 144 168 72 96 120 144 168
Dimensions (inches) W 66 66 66 66 66 36 36 36 36 36
H 57 1/2 57 1/2 57 1/2 57 1/2 57 1/2 57 1/2 57 1/2 57 1/2 57 1/2 57 1/2
Coppered Cold Pan BTUH @15º F Evap 2400 3600 4800 5400 6600 1200 1800 2400 2700 3300
ELECTRICAL REQUIREMENTS • Unit is pre-wired to 120V/208A plug, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NSF, NEC, and UL standards. • Amperage and voltage varies depending on the configuration. OPTIONS • Rear wall of inline olive can be mirrored to enhance merchandising visibility. • Counter top available in stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. • Powder coated canopy assembly. • Canopy in wood with lift up glass, clear view with fixed glass, and clear view with lift up glass. • Cold pan is available flat or sloped with either coppered or air over technology. • Bar packages can provide inset pans, lids, tongs, ladles, serving spoons, and salad dressing templates. • Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, cups/bowls, lids, and napkins. • Recesses for takeout containers or trays. • Product enhancing lights. • Attractive recessed accent lighting around counter top. • Stainless or mirrored laminate accent strip. • Self contained refrigeration. • Base to be solid, adjustable legs, or legs with removable toe-kick. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 29
R&D
Mobile Olive
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET • Pan to consist of an 18 gauge stainless steel interior and 18 gauge galvanized underneath exterior. • Base cabinet and counter top to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Fluorescent lights come with integral ballast, shatter shields, and a separate on/off switch. • Storage area below to house controls, electrical, and plumbing components. • Protective 1” vinyl bumpers. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. REFRIGERATED COLD ZONES • NSF-7 refrigerated, coppered cold pan holds standard 4” deep, 12” x 20” inset pans. • Custom inset pans available which sit flush on adjustable rails and eliminate flange between pans to give the look of continuous food. • Self-contained refrigeration supplied with a standard control. • Rated at 300 BTUs per full inset pan. • Adapter bars are included and allow for a variety of pan configurations. • Digital readout thermometer provided to verify temperature is maintained between 38º and 40ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 30
R&D
Mobile Olive
FIXTURES
A Division of COYOD, LLC.
Island Salad
Number of ¼ Size Pans
5' Island
16
Dimensions (inches) L W H 59 1/4 57 57 1/2
Coppered Cold Pan BTUH @15º F Evap 2400
ELECTRICAL REQUIREMENTS • Unit is pre-wired to 120V/208A plug, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NSF, NEC, and UL standards. • Amperage and voltage varies depending on the configuration. OPTIONS • Counter top available in stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. • Powder coated canopy assembly. • Canopy in wood with lift up glass, clear view with fixed glass, and clear view with lift up glass. • Bar packages can provide inset pans, lids, tongs, ladles, serving spoons, and salad dressing templates. • Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, cups/bowls, lids, and napkins. • Product enhancing lights. • Attractive recessed accent lighting around counter top. • Stainless or mirrored laminate accent strip. • Remote Refrigeration with a standard refrigeration control. • Base to be solid, adjustable legs, or legs with removable toe-kick. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 31
R&D
Mobile Olive
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (white, black, or almond)
2
optional colors available
• Canopy to consist of steel tubing, tempered glass, and fluorescent lighting. • Self-contained refrigerated, NSF-7 coppered cold pan all wired to standard refrigeration control. • Adapter bars included. • Tray recess in both sides. • Condensate evaporation pan. • Partially concealed castors. • 2 rows of protective vinyl bumper. • Unit is ready to accept 120V/30A, 60 Hz, 1 phase cord set. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor. Model
3 1
5’ Olive
Dimensions (L x D x H) Number of 1/4 Size Pans
64-1/4” x 52” x 57-1/2” 16
List Price
$17,947 Unit shown with optional finish.
Product Specifications Exterior
1
Counter Top
2
Standard
Options
List Price
White, Black, Almond Laminate
Other Finishes Available
Call for quote
Stainless Steel Corian CaesarStone Clear View with Fixed Glass Clear View with Lift Up Glass Mirror Laminate Accent-Strip Stainless Steel Accent Strip
$1,803 $3,075 Call for quote $1,153 Call for quote $79 $400
White, Black, Almond Laminate Stainless Frame with Lift Up Glass
Canopy Accent
3
None
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 32
R&D
Sandwich Grab-n-Go
FIXTURES
A Division of COYOD, LLC.
*Unit shown with optional features *End Panels available in Plexi or Mirrored Interior.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Ideal for merchandizing sandwiches or any cold packaged foods. • Galvanized steel frame construction and finished in high pressure plastic laminate. • Stainless steel interior. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable shelves and removable stainless steel deck pans. • Three shelves with ticket molding standard on all models. • Fluorescent lights illuminate shelf area below and come with integral ballasts and a separate on/off switch. REFRIGERATION SYSTEM • Unit comes standard with self contained energy efficient refrigeration system which eliminates the need for drain.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice. Page 33
R&D
Sandwich Grab-n-Go
FIXTURES
A Division of COYOD, LLC.
w
H
D
Sandwich Grab-NGo 3’ 4’ 6’ 3’ 4’ 6’
Dimensions (inches) W D H 36 32 1/2 55 48 32 1/2 55 72 32 1/2 55 36 32 1/2 78 48 32 1/2 78 72 32 1/2 78
BTUH @20ºF Evap 3500 5000 5000 5000 5000 5000
Volts
Phase
Amps (Remote)
120 120 120 120 120 120
1 1 1 1 1 1
2.7 2.7 2.7 2.7 2.7 2.7
Amps (Self Contained) 14 15 15 15 15 15
ELECTRICAL REQUIREMENTS • Unit is ready to accept 120V/20A, 60Hz, 1 phase circuit cord set. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Other finishes available. • Assorted colors for vinyl bumper. • Mirrored interior or plexi glass end panels. • Product enhancing lights. • Pull down, retractable night curtain. • Optional protective 1” vinyl bumper.
R&D Fixtures
Condensate pan requires direct 120V/8.34A
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 34
R&D
Sandwich Grab-n-Go
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Unit built with 14 gauge steel frame and finished with high pressure plastic laminate exterior (white, black, or almond)
2
optional colors available
• Stainless steel interior. • Self-contained refrigeration. • Merchandising area includes T-5 fluorescent lighting and 3 stainless steel adjustable shelves. • Shelves adjust to 3 different angled positions. • Optional pull down, retractable night curtain. • Unit is ready to accept 120V/20A, 60Hz, 1 phase circuit cord set. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor. Sandwich Grab-NGo 3’ 4’ 6’ 3’ 4’ 6’
1
Dimensions (inches) W D H 36 32 1/2 55 48 32 1/2 55 72 32 1/2 55 36 32 1/2 78 48 32 1/2 78 72 32 1/2 78
List Price $13,748 $14,747 $24,359 $16,370 $18,834 $26,573
To accommodate all your merchandising needs: Shelves can be adjusted to 3 different angled positions.
Product Specifications
Standard
Options
List Price
Exterior 2 Interior
White, Black, Almond Laminate Stainless Steel
Call for quote Call for quote
Night Curtain
No Curtain
Interior End Panels Interior End Panels End Panels Refrigeration
Laminate Laminate Laminate Self Contained
Other Finishes Available Various Powder Coat Colors Pull Down, Retractable Night Curtain Mirror Stainless Plexi Glass Window Remote
1
R&D Fixtures
$190 $239 Call for quote $239 Call for quote
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 35
R&D
Dual-Zone Merchandiser
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Unit built with 14 gauge steel frame and finished with high pressure plastic laminate exterior. • End panels have mirrored interior and are removable allowing multiple units to be connected in an endless series. • 1/4” thick tempered double bent curved glass with lift handle. • Rear access clear sliding doors. • Top to be 18 gauge stainless steel. • Two rows of protective 1” vinyl bumpers. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable 1/4” thick tempered glass shelves and 18 gauge steel deck pans are easily removable. • Five standard shelves on all models, extra shelves are optional. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch. REFRIGERATION SYSTEM • Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. • Digital readout thermometer provided to verify cabinet temperature is maintained between 65º and 70ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 36
R&D
Dual-Zone Merchandiser
FIXTURES
A Division of COYOD, LLC.
Dimensions* (inches) W D H 59 1/2" 41 1/2" 51 1/2"
Euro Bakery 59” Service Refrigerated
BTUH @20°F Evap 5000
Volts
Phase
Amps
120
1
3.5
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Powder coated interior and top. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Extra shelves. • Wire or sheet metal shelves in lieu of glass. • Front accent lighting. • Product enhancement bulbs. • End panels available in solid wood or glass. • Self contained refrigeration. • Available for glycol systems. • Cord set available in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 37
R&D
Dual-Zone Merchandiser
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES Unit built with 14 gauge steel frame and finished in high pressure plastic laminate exterior. (white, black, or almond) optional colors available Interior to be powder coated steel. Mirrored rear sliding doors and removable side panels. Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. Refrigerated merchandising area includes T-5 fluorescent lighting and five adjustable glass shelves with ticket molding. 2 rows of protective vinyl bumper. Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. Built in accordance with NEC, UL, and NSF standards. Contact factory for assorted finishes, bar accessories, and alternative configurations. Warranty is one year parts and labor. Model
List Price
Dimensions* (L x D x H) Dual-Zone with Remote Refrigeration
59-1/2" x 41-1/2” x 51-1/2”
Dual-Zone with Self-Contained Refrigeration
$30,483
$26,655
*Dimensions include end panels. Each end panel is ¾”. Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
Options
List Price
1
White, Black, Almond Laminate Powder Coated Black
3
None
Other Laminate Colors Various Powder Coat Colors Accent Down-Lighting Mirror Laminate Accent Strip Stainless Steel Accent Strip Cord Set
Call for quote Call for quote $735 $79 $250 $70
Exterior 2 Interior Accent
Electrical Connection
R&D Fixtures
Junction Box
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 Fax (615) 758-1006
www.rdfixtures.com
sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 38
R&D
Sandwich/Sushi/Pizza Prep Case
FIXTURES
A Division of COYOD, LLC.
Shown with optional curved glass.
Service view with rear refrigerated storage.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Ideal for preparing and merchandizing sandwiches, sushi, pizza, or any cold packaged foods. • Unit features a merchandising front, prep counter, and rear storage which are all refrigerated. • Front, end panels, and all edges to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Frame to consist of square steel tubing. Sneeze guard to be 1-1/4” round steel tubing. • One row of protective 1” vinyl bumper. • 7” high black toe-kick base. • Optional 1-1/4” adjustable levelers provided at all four corners. Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable shelves and deck pans are easily removable. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • One shelf in merchandising area and one shelf in storage area standard on all models. Extra shelves are optional. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch. REFRIGERATION SYSTEM • Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. • Digital readout thermometer provided to verify cabinet temperature is maintained between 38º and 40ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup. • Optional rear refrigerated storage has a blower coil with NSF certified coating, wire shelving, clear insulated sliding doors, incandescent lights, and a thermometer.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 39
R&D
Sandwich/Sushi/Pizza Prep Case
FIXTURES
A Division of COYOD, LLC.
Shown with optional rear refrigerated storage and curved glass.
Sandwich/ Sushi/Pizza Prep Case 4’ 6’ 8’
1/4 Size Prep Pans 6 9 11
W 49 1/2 73 1/2 97 1/2
Dimensions (inches) D 53 5/8 53 5/8 53 5/8
H 54 1/8 54 1/8 54 1/8
BTUH @20ºF Evap 2600 3900 5200
Volts
Phase
Amps
120 120 120
1 1 1
4.5 6 7.5
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Night covers for food prep pans. • Powder coated interior and sneeze guard. • Curved of straight tempered glass sneeze guard. • Counter top to be laminate, stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. • Bar packages can provide inset pans, lids, tongs, ladles, serving spoons, and salad dressing templates. • Extra shelves. • Wire or glass shelves in lieu of sheet metal. • End panels have mirrored interior. • Optional rear refrigerated storage includes clear sliding doors. Mirrored or solid available. • Product enhancing lights. • End panels available in solid wood or glass. • Available for glycol systems. • Cord set available in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 40
R&D
Sandwich/Sushi/Pizza Prep Case
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Unit built with 14 gauge steel frame and finished in high pressure plastic laminate exterior. (white, black or almond) optional colors available • Interior to be powder coated steel and mirrored side 2 panels. • Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. (Self-contained not avaiable.) • Refrigerated merchandising area includes T-5 fluorescent lighting and one adjustable steel shelf with ticket molding. • Prep area includes refrigerated 1/4 pans. • Rear refrigerated storage includes clear sliding doors and one adjustable shelf. • 1 row of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
Model Dimensions (L x D x H) Number of 1/4 Size Prep Pans
4 3
1
Shown with curved glass sneeze guard.
4’ Sandwich
6’ Sandwich
8’ Sandwich
49-1/2" x 53-5/8” x 54-1/8”
73 1/2" x 53-5/8” x 54-1/8”
97 1/2" x 53-5/8” x 54-1/8”
6
9
11
List Price
$23,283
$25,627
$29,994
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
1
Exterior 2 Interior
Counter Top
3
Sneeze Guard
R&D Fixtures
White, Black, Almond Laminate Powder Coated Black White, Black, Almond Laminate Straight Glass Stainless Steel Posts
4
Options
Other Finishes Available Various Powder Coat Colors Other Laminate Colors Stainless Steel Corian CaesarStone Curved Glass Powder Coated Posts
List Price
Call for quote Call for quote Call for quote $1,523 $2,869 Call for quote $1,852 Call for quote
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 41
R&D
RefrigHrated Mobile Low Back
FIXTURES
A Division of COYOD, LLC.
4’ Refrigerated Mobile
2’ Refrigerated Mobile
Shown with wood grain laminate.
Shown with optional dry shelf.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Ideal for merchandizing any cold packaged foods. • Exterior to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Steel frame construction. • Two rows of protective 1” vinyl bumper. • 3-1/2” swivel casters. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. REFRIGERATION SYSTEM • Unit comes standard as self contained energy efficient refrigeration system which also eliminates need for floor drain.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 42
R&D
RefrigHrated Mobile Low Back
FIXTURES
A Division of COYOD, LLC.
Refrig. Mobile High Back 2’ 4’ 6’
Dimensions (inches) W D H 24 45 42 48 45 42 72 45 42
BTUH @20ºF Evap 2500 4500 6000
Volts
Phase
Shelf Lights
Amps (Self Contained)
120 120 120
1 1 1
1 1.2 1.2
14.6 19.6 26.6
ELECTRICAL REQUIREMENTS • Unit is ready to accept 120V, 60Hz, 1 phase circuit cord set (amperage varies according to size). • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Other finishes available. • Night covers available. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Ticket molding. • Available for glycol systems. • Stainless steel interior. • Adjustable 19” top shelf. • Powder coated interior.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 43
R&D
Refrigerated Mobile /RZ %DFk
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Cabinet built with steel frame and finished with high pressure plastic laminate (white, black or almond)
3
optional colors available
Interior to be powder coated steel. Self contained energy efficient refrigeration system. 1 row of protective vinyl bumper. Unit is ready to accept 120V, 60Hz, 1 phase circuit cord set (amperage varies according to size). • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor. • • • •
2
1
Shown with optional dry shelf.
Model
2’ Refrigerated Mobile Low Back
4’ Refrigerated Mobile Low Back
6’ Refrigerated Mobile Low Back
Dimensions (L x D x H)
24" x 45� x 42�
48" x 45� x 42�
72" x 45� x 42�
Cost
$10,502
$12,846
$13,868
$10,959
$13,303
$1
$11,474
$13,818
$
w/ Shelf
3
w/ Shelf & 3 Lighting
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
1
Exterior 2 Interior
White, Black, Almond Laminate Powder Coated Black
Options
Other Finishes Available Various Powder Coat Colors
List Price
Call for quote Call for quote
Cases ship within 10 business days with the standard specifications listed, first-come first-serve basis, stock may be limited while in replenishment mode.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 44
R&D
Refrigerated Mobile High Back
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Ideal for merchandizing any cold packaged foods. • Unit built with 14 gauge steel frame and finished with high pressure plastic laminate exterior (white, black or almond) optional colors available • Fluorescent top light with integral ballast, shatter shield, and a separate on/off switch. • Two rows of protective 1” vinyl bumper. • 3-1/2” swivel casters. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable shelves and deck pans are easily removable. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Two shelves standard. Extra shelves are optional. REFRIGERATION SYSTEM • Unit comes standard with self contained energy efficient refrigeration system which also eliminates need for floor drain.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 45
R&D
Refrigerated Mobile High Back
FIXTURES
A Division of COYOD, LLC.
Refrig. Mobile High Back 2’ 4’ 6’
Dimensions (inches) W D H 24 45 59 48 45 59 72 45 59
BTUH @20ºF Evap 2500 4500 6000
Volts
Phase
Shelf Light Amp
Amps (Self Contained)
120 120 120
1 1 1
1 1.2 1.2
14.6 19.6 26.6
ELECTRICAL REQUIREMENTS • Unit is ready to accept 120V, 60Hz, 1 phase circuit cord set (amperage varies according to size). • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Other finishes available. • Night covers available. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Extra shelves. • Wire or glass shelves in lieu of sheet metal. • Lighted shelves. • Product enhancing lights. • Ticket molding. • Adjustable 19” top shelf.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 46
R&D
Refrigerated Mobile High Back
FIXTURES
A Division of COYOD, LLC.
3
STANDARD FEATURES • Unit built with 14 gauge steel frame and finished with high pressure plastic laminate exterior (white, black or almond) optional colors available • Interior to be powder coated steel. • Self-contained energy efficient refrigeration system. • Refrigerated merchandising area includes standard top light and two adjustable steel shelves. • 1 row of protective vinyl bumper. • Unit is ready to accept 120V, 60Hz, 1 phase circuit cord set (amperage varies according to size). • Built in accordance with NEC, UL, and NSF standards. • Warranty is one year parts and labor.
Shown with optional dry shelf. Shown with optional dry shelf.
Model
2’ Refrigerated Mobile High Back
4’ Refrigerated Mobile High Back
6’ Refrigerated Mobile High Back
Dimensions (L x D x H)
24" x 45” x 59”
48" x 45” x 59”
72" x 45” x 59”
List Price
$10,855
$13,123
$19,318
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
1
Exterior 2 Interior Shelves 3 Extra Dry Shelf 3 Extra Dry Shelf
White, Black, Almond Laminate Powder Coated Black Without Lights No Shelf No Shelf
Options
Other Finishes Available Various Powder Coat Colors (2) Shelf Lights Top Shelf Top Shelf with Light
List Price
Call for quote Call for quote $1,042 $457 $972
Cases ship within 10 business days with the standard specifications listed, first-come first-serve basis, stock may be limited while in replenishment mode.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 47
R&D
,VODQG Round Soup
FIXTURES
A Division of COYOD, LLC.
60” Half Round Soup* *Pictures shown with optional features. 60” Island Round Soup* SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet to consist of double thick 3/8” bendable plywood finished in high pressure plastic laminate. • Counter top finished in high pressure plastic laminate. • Storage area below to house controls, electrical, and plumbing components. • Two rows of protective 1” vinyl bumpers. • 6” high stainless steel adjustable legs. Unit must be leveled plumb at time of installation. • Stainless Steel corner protectors on Half Round Soup cases. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. CANOPY • Overhead canopy to consist of square stainless steel tubing,18 gauge formed stainless steel top, and tempered glass. • Compact fluorescent lights come with integral ballast, shatter shields, and a separate on/off switch. HEATED FOOD MERCHANDISING • NSF-4 soup wells are available in two types, Warmers or Cook-N-Holds. • Drains connected through a manifold to a single drain valve. • Infinite control with pilot light.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 48
R&D
,VODQG Round Soup
FIXTURES
A Division of COYOD, LLC.
Dimensions (inches)
Round Soup
D 48 60 48 60
48” 60” 48” Half 60” Half
60” Island Round Soup*
H 57 1/2 57 1/2 57 1/2 57 1/2
Volts
Phase
Amps
120/208 120/208 120/208 120/208
1 1 1 1
28.4 41.8 15.0 21.6
ELECTRICAL REQUIREMENTS Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. All units built in strict accordance with all applicable NEC, UL, and NSF standards. Amperage and voltage varies depending on the configuration. OPTIONAL ACCESSORIES Fixture is customizable and can accommodate limitless configurations. Counter top available in stainless steel, solid surface, or quartz engineered stone. Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. Canopy without tempered glass. Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, cups/bowls, lids, and napkins. Stainless or mirrored laminate accent strip.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 Fax (615) 758-1006
www.rdfixtures.com
sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 49
R&D
,VODQG Round Soup
FIXTURES
A Division of COYOD, LLC.
3
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (black, white, and almond).
2
Other finishes available
• Canopy to consist of formed steel top, compact fluorescent lighting, and tempered glass. • NSF-4 soup wells with insets, lids and ladles. • Cup dispensers and accessory pans. • 2 rows of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • Unit comes standard with soup inserts, lids and ladles. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes and alternative configurations. • Warranty is Model 48” R ound S oup parts and
Canopy* Accent
Number of Wells
4 (7 qt)
6 (7 qt)
Cup dispensers
4
3
Accessory Pans
2
3
List Price
$19,715
$24,403
Standard
White, Black, Almond Laminate
2
White, Black, Almond Laminate With Glass
4
None 5
Warmers
one year labor
60” R ound S oup 60” x 57-1/2”
3
Soup Wells
1
48” x 57-1/2”
1
Counter Top
4
Dimensions (D x H)
Product Specifications Exterior
5
Options
Other Finishes Available Other Laminate Colors Stainless Steel Corian CaesarStone Without Glass Mirror Laminate Accent Strip Stainless Steel Accent Strip Cook-n-Holds (with Circuit Breaker Panel)
Cost
Call for quote Call for quote $2,601 $3,305 Call for quote Call for quote $79 $638 (48”) $1,124 (60”) $1,918
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 50
R&D
Half Round Soup
FIXTURES
A Division of COYOD, LLC.
3
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (white, black or almond) optional colors available • Canopy to consist of formed steel top, compact fluorescent lighting, and tempered glass. • NSF-4 soup wells with insets, lids and ladles. • Cup dispenser(s) and accessory pan(s). 5 • 2 rows of protective vinyl bumper and corner guards. • Stainless Steel corner protectors. • Unit is pre-wired and furnished with a junction box for use 1 on a dedicated 120V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
48” Half R ound S oup
60” Half R ound S oup
48” x 24” x 57-1/2”
60” x 30-1/2” x 57-1/2”
Number of Wells
(2) 7qt.
(3) 7qt.
Cup Dispensers
(2)
(3)
Accessory Pans
(1)
(1)
List Price
$12,288
$13,227
Model
Dimensions (W x D x H)
Product Specifications 1
Exterior
Counter Top Canopy* Accent
3
Soup Wells
Options
Cost
White, Black, Almond Laminate
Other Finishes Available
Call for quote
Other Laminate Colors Stainless Steel Corian CaesarStone Without Glass Mirror Laminate Accent Strip Stainless Steel Accent Strip Cook-n-Holds
Call for quote $2,284 $3,033 Call for quote Call for quote $79 $400
With Glass
4
None 5
Warmers
not available for 48”
4
Standard
White, Black, Almond Laminate
2
2
$1,017
(with Circuit Breaker Panel)
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 51
R&D
End Cap Soup
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet and counter top to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Storage area below to house controls, electrical, and plumbing components. • Three rows of protective 1” vinyl bumpers. • 6” high stainless steel adjustable legs. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. CANOPY • Sneeze guard is not required in some jurisdictions. • Overhead canopy to consist of square steel tubing, 3/4” laminated plywood, and tempered glass. • Sneeze guard has a hinged, lift-up feature to ease cleaning. • Fluorescent lights come with integral ballast, shatter shields, and a separate on/off switch. HEATED FOOD MERCHANDISING • NSF-4 soup wells are available in two types, Warmers or Cook-N-Holds. • Drains connected through a manifold to a single drain valve. • Infinite control with pilot light.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 52
R&D
End Cap Soup
FIXTURES
A Division of COYOD, LLC.
End Cap Soup 48” 60”
Dimensions (L x D x H) 48”x38-1/4”x58-1/2” 60” x 38-1/4” x 58-1/2”
Volts
Phase
Amps
120/208V 120/208V
1 1
41.8 41.8
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. • Amperage and voltage varies depending on the configuration. OPTIONAL ACCESSORIES • Fixture is customizable and can accommodate limitless configurations. • Counter top to be stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. • Powder coated canopy assembly. • Canopy in clear view with fixed glass or with lift up glass. • Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, cups/bowls, lids, and napkins. • Attractive recessed accent lighting around counter top. • Stainless or mirrored laminate accent strip. • Stainless steel corner protectors. • Removable toe-kick or solid toe-kick base.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 53
R&D
End Cap Soup
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base of cabinet and counter top finished with high pressure plastic laminate (white, black, or almond) optional colors available
4
• Standard wood canopy to consist of lift up 2 tempered glass and fluorescent lighting. • NSF-4 soup wells with insets, lids and ladles. • 2 cup and 2 napkin dispensers with 2 accessory pans. • 3 rows of protective vinyl bumper and corner 3 guards. • Unit is pre-wired and furnished with a Circuit Breaker Panel for use on a dedicated 120V, 1 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes and alternative configurations. • Warranty is one year parts and labor. • Contact factory for assorted finishes and alternative configurations Model 48” E nd C ap S oup 60” E nd C ap S oup Dimensions (W x D x H)
48”x38-1/4”x58-1/2”
60” x 38-1/4” x 58-1/2”
Number of Wells
3 (11 qt)
3 (11qt)
List Price
$16,022
$16,044
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
Options
Cost
Exterior
White, Black, Almond Laminate
Other Finishes Available Other Laminate Colors Stainless Steel Corian CaesarStone Mirror Laminate Accent Strip Stainless Steel Accent Strip Cook-n-Holds (with Circuit Breaker Panel)
Call for quote Call for quote $2,284 $3,033 Call for quote $79 $400
1
Counter Top Accent
White, Black, Almond Laminate
3
Soup Wells
R&D Fixtures
2
None 4
Warmers
$1,017
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 54
R&D
Service Hot Food Line Up
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Storage area has shelving and houses electrical and plumbing components. • Sneeze guard to be round steel tubing and tempered glass. • Three rows of protective 1” vinyl bumpers. • Black toe-kick base. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. HEATED FOOD MERCHANDISING • Hot food wells and hot food plates are NSF-4 and warm uniformly keeping product at optimum temperature. • Hot food wells can be used wet or dry (wet offers better results). • Decorative heat lamps provide light and additional heat. • Drains connected through a manifold to a single drain valve. • Infinite control with pilot light.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 55
R&D
Service Hot Food Line Up
FIXTURES
A Division of COYOD, LLC.
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. • Amperage and voltage varies depending on the configuration.
OPTIONAL ACCESSORIES • Fixture is customizable and can accommodate limitless configurations. • Counter top to be laminate, stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. • Bar packages can provide inset pans, lids, tongs, ladles, serving spoons, and salad dressing templates. • Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, lids, and napkins. • Hot food wells have an optional auto-fill feature which uses a sensor and solenoid valve to eliminate the need to add water by hand as well as remove risk of unit being damaged from low water levels. • Stainless or mirrored laminate accent strip. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 56
R&D
Service Heated Stone Line Up
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet to consist of 3/4” plywood panels and bendable plywood finished in either high pressure plastic laminate or designer wallpaper. • Quartz engineered stone counter top. • Shown with maple accent strip. • Storage area has shelving and houses electrical and plumbing components. • One row of protective 1” vinyl bumper. • 6” high black toe-kick base. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SNEEZE GUARD • Overhead canopy to consist of square steel tubing and tempered glass. • Sneeze guard on straight line up has hinged, lift-up feature to ease cleaning. Not available on curved units. HEATED FOOD MERCHANDISING • NSF-4 heated deck plates radiate warmth uniformly keeping product at optimum temperature and have infinite control. • NSF-4 decorative heat lamps are placed ~16" above to add radiant heat. Lights come with shatter resistant coated bulbs and a separate on/off switch. Several lamp shades, colors, and mounting options are available. • Shown with optional NSF-4 hot wells.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 57
R&D
Service Heated Stone Line Up
FIXTURES
A Division of COYOD, LLC.
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. • Amperage and voltage varies depending on the configuration. OPTIONAL ACCESSORIES • Assorted colors available for counter top, laminate, vinyl bumper, heat lamps, and powder coat. • Bar packages can provide inset pans, lids, tongs, ladles, serving spoons, and salad dressing templates. • Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, cups/bowls, lids, and napkins. • Hot food wells have an optional auto-fill feature which uses a sensor and solenoid valve to eliminate the need to add water by hand as well as remove risk of unit being damaged from low water levels. • Stainless or mirrored laminate accent strip. • 6” high stainless steel adjustable legs. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 58
R&D
Island Hot Food
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Counter top to be high pressure plastic laminate. • Storage area has shelving and houses electrical and plumbing components. • Stainless steel corner protectors. • Three rows of protective 1” vinyl bumpers. • 6” high black toe-kick base. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. CANOPY • Overhead canopy to consist of square steel tubing, 3/4” laminated plywood, and tempered glass. • Sneeze guard has a hinged, lift-up feature to ease cleaning. • NSF-4 overhead warmer aids in holding product below to proper temperature and has an infinite control. • NSF-4 incandescent lights come with shatter resistant coated bulbs and a separate on/off switch. HEATED FOOD MERCHANDISING • NSF-4 hot food wells warm uniformly keeping product at optimum temperature. • Drains connected through a manifold to a single drain valve. • Infinite control with pilot light.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 59
R&D
Island Hot Food
FIXTURES
A Division of COYOD, LLC.
Island Steam Table 6’ 6’ 5” 8’
Number of Wells
W 72 77 96
4 5 6
Dimensions (inches) D 45 45 45
H 57 1/2 57 1/2 57 1/2
Volts
Phase
Amps
120/208 120/208 120/208
1 1 1
23.06 28.8 34.56
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a Circuit Breaker Panel for use on a dedicated 120/208V, 60Hz circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Counter top to be stainless steel, solid surface, or quartz engineered stone. • Canopy clear view with fixed glass, and clear view with lift up glass. • Hot food wells have an optional auto-fill feature which uses a sensor and solenoid valve to eliminate the need to add water by hand as well as remove risk of unit being damaged from low water levels. • Recesses for takeout containers or trays. • Product enhancing lights. • Attractive recessed accent lighting around counter top. • Stainless or mirrored laminate accent strip. • 6” high stainless steel adjustable legs with a black removable toe-kick.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 60
R&D
Island Hot Food
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (white, black, or almond) optional colors available
• Canopy to consist lift up tempered glass, incandescent lighting and finished with high pressure laminate. • NSF-4 heated steam well area includes overhead heat. • 3 rows of protective vinyl bumper and corner guards. • Unit is pre-wired and furnished with a Circuit Breaker Panel for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
Model Dimensions (L x D x H) Number of Wells (12 X 20) List Price
4
2
3
1
6’ Is land S team
6’ 5” Is land S team
8’ Is land S team
72” x 45” x 57-1/2”
77” x 45” x 57-1/2”
96” x 45” x 57-1/2”
4
5
6
$20,482
$22,935
$25,697
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
Options
List Price
Exterior
White, Black, Almond Laminate
Other Finishes Available Other Laminate Colors Stainless Steel Corian CaesarStone Mirror Laminate Accent Strip Stainless Steel Accent Strip Auto-Fill
Call for quote Call for quote $1,626 $2,951 Call for quote $79 $272 $1,803
1
Counter Top Accent
White, Black, Almond Laminate
3
Steam Wells
R&D Fixtures
2
None 4
Fill by Hand
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 61
R&D
Self Serve Inline Hot Food
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet and counter top to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Storage area has shelving and houses electrical and plumbing components. • Stainless steel corner protectors. • Two rows of protective 1” vinyl bumpers. • 6” high stainless steel adjustable legs. Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. CANOPY • Overhead canopy to of consist of square steel tubing and tempered glass. • Back sliding plexi doors. • Sneeze guard has a hinged, lift-up feature to ease cleaning. • NSF-4 overhead warmer aids in holding product below to proper temperature and has an infinite control. • NSF-4 incandescent lights come with shatter resistant coated bulbs and a separate on/off switch. HEATED FOOD MERCHANDISING • NSF-4 hot food wells warm uniformly keeping product at optimum temperature. • Hot food wells can be used wet or dry (wet offers better results). • Drains connected through a manifold to a single drain valve. • Infinite control with pilot light.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 62
R&D
Self Serve Inline Hot Food
FIXTURES
A Division of COYOD, LLC.
Inline Steam Table 6’ 6’ 5” 8’ 10’ 12’ 6”
Number of Wells
W 72 77 96 120 150
4 5 6 8 10
Dimensions (inches) D 45 45 45 45 45
H 56 5/8 56 5/8 56 5/8 56 5/8 56 5/8
Volts
Phase
Amps
120/208 120/208 120/208 120/208 120/208
1 1 1 1 1
23.066 28.83 34.6 46.12 57.66
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Counter top can be finished with stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, and powder coat. • Bar packages can provide inset pans, lids, tongs, ladles, serving spoons, and salad dressing templates. • Counter top configurations available to include tray slides, utensil holders, small pans, and dispensers for plates, cups/bowls, lids, and napkins. • Hot food wells have an optional auto-fill feature which uses a sensor and solenoid valve to eliminate the need to add water by hand as well as remove risk of unit being damaged from low water levels. • Recesses for takeout containers or trays. • Product enhancing lights. • Stainless or mirrored laminate accent strip. • Black removable toe-kick or solid base. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 63
R&D
Self Serve Inline Hot Food
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (white, black, or almond)
2
optional colors available
• Front recessed storage. • Canopy to consist of steel tubing, lift up tempered glass, and overhead heat. • NSF-4 heated steam well area includes overhead heat. • Back sliding plexi doors. • 2 rows of protective vinyl bumper and corner guards. 4 • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V,60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Unit designed for easy cleaning. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor. 6’ S elf S erve 6’ 5” S elf S erve 8’ S elf S erve Model S team S team S team Dimensions (L x D x H) Number of Wells (12 X 20)
1
3
10’ S elf S erve S team
12’ 6” S elf S erve S team
72” x 45” x 56-5/8”
77” x 45” x 56-5/8”
4
5
6
8
10
$23,739
$24,376
$27,639
$34,704
$44,684
List Price
96” x 45” x 56-5/8” 120” x 45” x 56-5/8” 150”x45”x56-5/8”
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications Exterior
1
Counter Top Accent
2
Standard
Options
List Price
White, Black, Almond Laminate
Other Finishes Available Other Laminate Colors Stainless Steel Corian CaesarStone Mirror Laminate Accent Strip Stainless Steel Accent Strip Auto-Fill
Call for quote Call for quote $1,918 $3,112 Call for quote $79 $276 $3,260
White, Black, Almond Laminate
3
Steam Wells
None 4
Fill by Hand
Drawing shows optional second tier. Call for quote.
Optional End Stations Available for Inline Cases Details on pages 20 & 21
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 64
R&D
Service Inline Hot Food
FIXTURES
A Division of COYOD, LLC.
Shown with optional lift up glass. SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Counter top to be high pressure laminate • Storage area has shelving and houses electrical and plumbing components. • Two rows of protective 1” vinyl bumpers. • 6” high stainless steel adjustable legs. Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. CANOPY • Overhead canopy to consist of square steel tubing and fixed tempered glass. • Back sliding plexi doors. • NSF-4 overhead warmer aids in holding product below to proper temperature and has an infinite control. • NSF-4 incandescent lights come with shatter resistant coated bulbs and a separate on/off switch. HEATED FOOD MERCHANDISING • NSF-4 hot food wells warm uniformly keeping product at optimum temperature. • Drains connected through a manifold to a single drain valve. • Infinite control with pilot light.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 65
R&D
Service Inline Hot Food
FIXTURES
A Division of COYOD, LLC.
"W"
565 8" 45"
Service Steam Table 6’ 6’ 5” 8’ 10’ 12’ 6”
Number of Wells
W 72 77 96 120 150
4 5 6 8 10
Dimensions (inches) D 45 45 45 45 45
H 56 5/8 56 5/8 56 5/8 56 5/8 56 5/8
34"
Volts
Phase
Amps
120/208 120/208 120/208 120/208 120/208
1 1 1 1 1
23.066 28.83 34.6 46.12 57.66
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a Circuit Breaker Panel for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Counter top available in stainless steel, solid surface, or quartz engineered stone. optional finishes available • Hot food wells have an optional auto-fill feature which uses a sensor and solenoid valve to eliminate the need to add water by hand as well as remove risk of unit being damaged from low water levels. • Lift up glass for easy cleaning. • Black removable toe-kick or solid base. • Stainless steel corner protectors. • Stainless or mirrored laminate accent strip.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 66
R&D
Service Inline Hot Food
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (white, black, or almond)
5 1
optional colors available
4
• Canopy to consist of steel tubing, fixed tempered glass, and overhead heat. • NSF-4 heated steam well area includes overhead heat. • Back sliding plexi doors. • 2 rows of protective vinyl bumper and corner guards. • Unit is pre-wired and furnished with a Circuit Breaker Panel for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Unit designed for easy cleaning. • Contact factory for assorted finishes, pans, bar accessories, and alternative configurations. • Warranty is one year parts and labor. 6’ S ervice S team
Model Dimensions (L x D x H) Number of Wells (12 X 20)
6’ 5� S ervice S team
8’ S ervice S team
10’ S ervice S team
2
12’ 6� S ervice S team
72� x 45� x 56-5/8� 77� x 45� x 56-5/8� 96� x 45� x 56-5/8� 120� x 45� x 56-5/8� 150�x45�x56-5/8� 4
List Price
5
$24,376
6
8
10
$31,723
$38,652
$44,678
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
Options
List Price
Exterior
White, Black, Almond Laminate
Other Finishes Available Stainless Steel Corian CaesarStone Mirror Laminate Accent Strip Stainless Steel Accent Strip Auto-Fill Lift Up for Easy Cleaning
Call for quote $1,914 $3,116 Call for quote $79 $276 $2,675 Call for quote
1
Counter Top Accent
2
White, Black, Almond Laminate
3
None 4
Steam Wells 5 Sneeze Guard Glass
Manual Fill Fixed
Optional End Stations Available for Inline Cases Details on pages 20 & 21
R&D Fixtures
3
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 67
R&D
Multi-Deck Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Interior to be stainless steel. • One row of protective 1” vinyl bumpers. • Toe-kick base. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. HEATED SHELVING • Stainless steel shelves and deck. • Shelves include 3” price tag molding. • NSF-4 incandescent light fixtures come with shatter resistant coated bulbs and a separate on/off switch. • NSF-4 heated deck plates radiate warmth uniformly keeping product at optimum temperature and have digital control. • Optional front or rear temperature controls.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 68
R&D
Multi-Deck Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
w
Multi-Deck Rotisserie 4’ 6’ 8’
Capacity (packaged chickens) 28 44 60
Dimensions (inches) W D H 48 24 56 72 24 56 96 24 56
Volts
Phase
Amps
120/208 120/208 120/208
1 1 1
14.2 21.3 28.4
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Other finishes available. • Assorted colors available vinyl bumper. • Rear access clear or mirrored sliding doors. • Controls accessible in front or back of unit.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 69
R&D
Multi-Deck Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES Cabinet finished with high pressure plastic laminate (white, black, or almond)
2
optional colors available
Stainless Steel interior. Optional front or rear temperature controls. Heated merchandising area includes three shelves and a deck with incandescent lighting. Front temperature and lighting controls available if back of unit is blocked. 1 row of protective vinyl bumper and corner guards. Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. Built in accordance with NEC, UL, and NSF standards. Contact factory for assorted finishes, bar accessories, and alternative configurations. Warranty is one year parts and labor.
4’ MDR
Model Dimensions (L x D x H) Number of Packaged Chickens (approx)
1
3
6’ MDR
8’ MDR
48” x 24” x 56” 72” x 24” x 56” 96” x 24” x 56”
List Price
28
44
60
$20,036
$24,234
$32,969
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications Exterior
1
Rear Doors Controls Accent
R&D Fixtures
Standard
Options
List Price
White, Black, Almond Laminate
Other Finishes Available
Call for quote
No Doors
Mirrored Sliding Doors
Assessable in Rear
Assessable in Front
None
Mirror Laminate Accent Strip Stainless Steel Accent Strip
$1,893 Choose when placing order $79 $474
2
3
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 Fax (615) 758-1006
www.rdfixtures.com
sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 70
R&D
Island Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
Single Tier Island Hot Food Merchandiser (4 x 6)*
Two Tier Island Hot Food Merchandiser (4 x 6)*
*Pictures may have optional features.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Stainless steel counter top. • Storage area below to house controls, electrical, and plumbing components. • Stainless steel corner protectors. • One row of protective 1” vinyl bumpers. • 4” high black or stainless steel toe-kick base. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. HEATED SHELVING • Shelves and deck to be stainless steel with steel rod or tempered glass product stops. • Shelves provided with NSF-4 overhead warmers which hold the product below to proper temperature and have an infinite control. • NSF-4 incandescent light fixtures come with shatter resistant coated bulbs and a separate on/off switch. • NSF-4 heated deck plates radiate warmth uniformly keeping product at optimum temperature and have infinite control.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 71
R&D
Island Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
Island Rotisserie
Capacity (packaged chickens)
3x5 Single Tier 3x5 Double Tier 3x6 Single Tier 3x6 Double Tier 4x6 Single Tier 4x6 Double Tier
14 26 18 32 31 49
L 56-1/2 56-1/2 68-1/2 68-1/2 80 80
Dimensions (inches) D 36-3/4 36-3/4 36-3/4 36-3/4 48 48
H 52-1/2 67-1/4 52-1/2 67-1/4 52-1/2 67-1/4
Volts
Phase
Amps
120 120 120 120 120/208 120/208
1 1 1 1 1 1
34.2 47.3 42.8 59.4 32.5 40.0
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NSF, NEC, and UL standards. OPTIONAL ACCESSORIES • Powder coated canopy assembly. • Other finishes available. • Assorted colors available for laminate and vinyl bumper. • Attractive recessed accent lighting around counter top. • Stainless or mirrored laminate accent strip. • Circuit Breaker Panel in lieu of junction box. Shown with Stainless Steel Exterior
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 72
R&D
Island Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base of cabinet finished with high pressure plastic laminate ( white, black or almond) optional colors available
• Stainless steel canopy. • Heated merchandising area includes incandescent lighting and overhead heat. • 1 row of protective vinyl bumper and corner guards. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
Model
3’x 5’ S ingle Tier
3’x 5’ Two Tier
3’x 6’ S ingle Tier
2
1
3’x 6’ Two Tier
Dimensions 56-1/2” x 36-3/4” 56-1/2” x 36-3/4” 68-1/2” x 36-3/4” 68-1/2” x 36-3/4” x 67-1/4” (L x D x H) x 52-1/2” x 67-1/4” x 52-1/2” Number of Packaged 14 26 18 32 Chickens List Price
$18,513
$23,484
$19,269
4’x 6’ S ingle Tier
4’x 6’ Two Tier
31
49
$24,022
$27,149
$23,674
80” x 48” x 52-1/2”
80” x 48” x 67-1/4”
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
Options
List Price
Exterior
1
White, Black, Almond Laminate
Accent
2
None
Other Finishes Available Accent Down-Lighting Mirror Laminate Accent Strip Stainless Steel Accent Strip
Call for quote $1,980 $79 $326
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 73
R&D
Octagon Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Base cabinet to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Frame to consist of square mild steel tubing. • Storage area below to house controls, electrical, and plumbing components. • Stainless steel corner protectors. • One row of protective 1” vinyl bumpers. • 6” high stainless steel adjustable legs with a black removable toe-kick. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. HEATED SHELVING • • • •
Shelves and deck to be stainless steel with steel rod or tempered glass product stops. Shelves provided with NSF-4 overhead warmers which hold the product below to proper temperature and have an infinite control. NSF-4 incandescent light fixtures come with shatter resistant coated bulbs and a separate on/off switch. NSF-4 heated deck plates radiate warmth uniformly keeping product at optimum temperature and have infinite control.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 74
R&D
Octagon Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
Octagon Rotisserie
Capacity (packaged chickens)
Single Tier Two Tier
16 32
Dimensions (inches) W D H 50 50 49 50 50 64
Volts
Phase
Amps
120/208 120/208
1 1
12.6 18.2
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Assorted colors available for laminate and vinyl bumper. • Stainless or mirrored laminate accent strip. • Circuit Breaker Panel in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 75
R&D
Octagon Hot Food Merchandiser
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base cabinet finished with high pressure plastic laminate (white, black, or almond) optional colors available
• Stainless steel canopy and shelving. • Heated merchandising area includes incandescent lighting and overhead heat. • 1 row of protective vinyl bumper and corner guards. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
2
1
Model
Dimensions (L x D x H) Number of Packaged Chickens
S ingle Tier Octagon
Two Tier Octagon
50” x 50” x 49”
50” x 50” x 64”
16
32
$20,580
$24,555
List Price
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
R&D Fixtures
Exterior
1
Accent
2
Standard
Options
White, Black, Almond Laminate
Other Finishes Available
None
List Price
Mirror Laminate Accent Strip Stainless Steel Accent Strip
Call for quote $79 $326
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 76
R&D
Inline Artisan Bread Merchandiser
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Ideal for preparing and merchandizing breads. • Cabinet and counter top to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Sneeze guard consists of 2” round wood posts with balls and 1/4” thick tempered glass. • Underneath prep counter is open storage and has pull out cutting boards. • One row of protective 1” vinyl bumpers. • 3” high toe-kick base. • Optional 1-1/4” adjustable levelers provided at all four corners. Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • 2” oak wood slat shelves. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Hardware is all powder coated.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 77
R&D
Inline Artisan Bread Merchandiser
FIXTURES
A Division of COYOD, LLC.
Inline Artisan Bread 4’ Merchandiser 6’ Merchandiser
W 48 72
Dimensions (inches) D 54 3/4 54 3/4
H 54 54
OPTIONAL ACCESSORIES • Counter top available in stainless steel, solid surface, or quartz engineered stone. • Assorted colors available for counter top, laminate, vinyl bumper, powder coat, and wood stain. • Mirrored interior back wall. • Curved tempered glass sneeze guard.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 78
R&D
Inline Artisan Bread Merchandiser
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Base cabinet and counter top finished with high pressure plastic laminate (white, black, or almond)
3 2
optional colors available
• Sneeze guard to be 2” round wood posts with balls and 1/4” thick tempered glass. • Merchandising area has a 2” oak wood slat shelf and deck. • Underneath prep counter is open storage and has pull out cutting boards. • 1 row of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V/15A, 60Hz,1 phase circuit. • Built in accordance with UL, NEC, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
Model Dimensions (W x D x H)
1
4’ Artis an B read
6’ Artis an B read
48” x 54-3/4” x 54”
72” x 54-3/4” x 54”
$9,942
$11,959
List Price
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications Exterior
1
Counter Top
2
Sneeze Guard
3
Shelf Light
R&D Fixtures
Standard
Options
List Price
White, Black, Almond Laminate
Other Finishes Available
Call for quote
White, Black, Almond Laminate
Other Laminate Colors Stainless Steel Corian CaesarStone
Call for quote $1,626 $2,618 Call for quote
Straight Glass
Curved Glass
$1,235
None
T-5 Fluorescent
(4’) $827 (6’) $1,284
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 79
R&D
Upright Artisan Bread Low Profile
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Ideal for merchandizing breads and bakery items. • Cabinet to consist of 3/4” plywood panels finished in high pressure plastic laminate. • One row of protective 1” vinyl bumpers. • 3” high toe-kick base. • Optional 1-1/4” adjustable levelers provided at all four corners. Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • 2” oak wood slat shelves. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Powdered coated hardware. • Optional fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and on/off switch.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 80
R&D
Upright Artisan Bread Low Profile
FIXTURES
A Division of COYOD, LLC.
51
Upright Artisan Bread 4’ Shelving 6’ Shelving
L 48 72
Dimensions (inches) D 34 1/2 34 1/2
H 51 51
Volts
Phase
Amps
120 120
1 1
1.6 2.1
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Assorted colors available for laminate, vinyl bumper, powder coat, and wood stain. • Mirrored interior back wall. • Extra shelves. • Product enhancing lights.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 81
R&D
Upright Artisan Bread Low Profile
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Cabinet finished with high pressure plastic laminate (white, black, or almond) Optional colors available
• Merchandising area has three 2” oak wood slats shown with optional lighted shelves. • 1 row of protective vinyl bumper. • For lighting option, unit is pre-wired and furnished with a junction box for use on a dedicated 120V/15A, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
Model Dimensions (W x D x H) List Price
1
4’ L ow P rofile S helving
6’ L ow P rofile S helving
48” x 34-1/2” x 51”
72” x 34-1/2” x 51”
$11,318
$11,862
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications Exterior
1
Shelf Light
R&D Fixtures
Standard
Options
List Price
White, Black, Almond Laminate
Other Finishes Available
Call for quote
None
T-5 Fluorescent
(4’) $1,959 (6’) $3,918
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 82
R&D
Upright Artisan Bread
FIXTURES
A Division of COYOD, LLC.
Unit shown without the Standard Canopy SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Ideal for merchandizing breads and bakery items. • Cabinet to consist of 3/4” plywood panels finished in high pressure plastic laminate. • One row of protective 1” vinyl bumpers. • 3” high toe-kick base. • Optional 1-1/4” adjustable levelers provided at all four corners. Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • 2” oak wood slat shelves. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Powdered coated silver ware. • Optional fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and on/off switch.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 83
R&D
Upright Artisan Bread
FIXTURES
A Division of COYOD, LLC.
81
Upright Artisan Bread 4’ Shelving 6’ Shelving
L 48 72
Dimensions (inches) D 34 1/2 34 1/2
H 81 81
Volts
Phase
Amps
120 120
1 1
2.1 2.6
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Assorted colors available for laminate, vinyl bumper, powder coat, and wood stain. • Mirrored interior back wall. • Extra shelves.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 84
R&D
Upright Artisan Bread
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Cabinet finished with high pressure plastic laminate (white, black, or almond) optional colors available
• Merchandising area has four 2” oak wood slats shown with optional lighted shelves. • 1 row of protective vinyl bumper. • For lighting option, unit is pre-wired and furnished with a junction box for use on a dedicated 120V/15A, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
1
Dimensions (W x D x H)
4’ S helving
6’ S helving
48” x 34-1/2” x 81”
72” x 34-1/2” x 81”
List Price
$12,064
$15,201
Model
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications Exterior
1
Standard
Options
List Price
White, Black, Almond Laminate
Other Finishes Available
Call for quote
None
T-5 Fluorescent
(4’) $2,684 (6’) $3,589
Shelf Light
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 85
R&D
Upright Pastry Case Low Profile
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Front, end panels, and all edges to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Top to be 3/8” thick tempered glass. • 1/4” thick tempered glass doors. • Front storage recesses for packaging supplies. • Two rows of protective 1” vinyl bumpers. • Deck to be laminated plywood, stainless steel available. • 5-1/2” high black toe-kick base. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable steel wire shelves are easily removable. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Three standard shelves on all upright models, extra shelves are optional. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 86
R&D
Upright Pastry Case Low Profile
FIXTURES
A Division of COYOD, LLC.
Pastry Case Low Profile 2 Door 3 Door 4 Door 5 Door
W 39 1/2 58 3/8 77 1/4 96 1/8
Dimensions (inches) D 44 44 44 44
H 51 51 51 51
Volts
Phase
Amps
120 120 120 120
1 1 1 1
1.5 3 3 4.5
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards.
OPTIONAL ACCESSORIES • Powder coated interior. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Extra shelves. • Glass or sheet metal shelves in lieu of wire. • Rear access clear or mirrored sliding doors. • Front accent lighting. • End panels available in solid wood with mirrored interior or glass.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 87
R&D
Upright Pastry Case Low Profile
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Cabinet finished with high pressure plastic laminate (white, black, or almond)
3
optional colors available
• Top to be 3/8” thick tempered glass. • Interior mirrored side panels and powder coated shelving. • Merchandising area includes T-5 fluorescent lighting and three adjustable wire shelves with ticket molding. • 1/4” thick tempered glass doors. • Front storage recesses for packaging supplies and trash receptacle(s). 2 • 2 rows of protective vinyl bumper • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • Unit comes standard with automatic door closures with stay open feature. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
1
Model
2 Door L UP C
3 Door L UP C
4 Door L UP C
5 Door L UP C
Dimensions (W x D x H)
39-1/2” x 44” x 51”
58-3/8” x 44” x 51”
77-1/4” x 44” x 51”
96-1/8” x 44”x 51”
Base Price
$12,226
$14,532
$16,626
$18,404
Mirrored Sliding Rear Doors
2 Door L UP C
3 Door L UP C
4 Door L UP C
5 Door L UP C
$437
$733
$807
$1,161
Product Specifications
Standard
Options
Base Price
Exterior 2 Interior 3 End Panels
Non-Premium Laminate Powder Coated Black Wood with Mirrored Interior
Other Finishes Available Various Powder Coat Colors Glass
Call for quote Call for quote $642
1
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 88
R&D
Upright Pastry Case
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Front, end panels, and all edges to consist of 3/4” plywood panels finished in high pressure plastic laminate. • 1/4” thick tempered glass doors. • Front storage recesses for packaging supplies. • Deck to be laminated plywood, stainless steel available. • Two rows of protective 1” vinyl bumpers. • 5-1/2” high black toe-kick base. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable steel wire shelves are easily removable. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Four standard shelves on all upright models, extra shelves are optional. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 89
R&D
Upright Pastry Case
FIXTURES
A Division of COYOD, LLC.
Pastry Case
W 39 1/2 58 3/8 77 1/4 96 1/8
2 Door 3 Door 4 Door 5 Door
Dimensions (inches) D 44 44 44 44
H 81 81 81 81
Volts
Phase
Amps
120 120 120 120
1 1 1 1
3.25 4.25 5.25 6.25
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Powder coated interior. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Extra shelves. • Glass or sheet metal shelves in lieu of wire. • Rear access clear or mirrored sliding doors. • End panels available in solid wood with mirrored interior or glass. • Radius top edge.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 90
R&D
Upright Pastry Case
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Cabinet finished with high pressure plastic laminate (white, black, or almond) optional colors available
• Merchandising area includes T-5 fluorescent lighting and four adjustable wire shelves with ticket molding. • 1/4” thick tempered glass doors. • Front storage recesses for packaging supplies and trash receptacle(s). • 2 rows of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Unit comes standard with automatic door closures with stay open feature. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor. 2 Door UP C
Model Dimensions (W x D x H)
3 Door UP C
4
3
2 1
4 Door UP C
39-1/2” x 44” x 81” 58-3/8” x 44” x 81” 77-1/4” x 44” x 81”
5 Door UP C 96-1/8” x 44” x 81”
List Price
$13,868
$14,222
$17,534
$19,253
Mirrored Sliding Rear Doors
2 Door UP C
3 Door UP C
4 Door UP C
5 Door UP C
$610
$1,050
$1,247
$1,647
Product Specifications
Standard
Options
List Price
Exterior
1
White, Black, Almond Laminate
Other Finishes Available
Call for quote
Interior
2
Powder Coated Black
Various Powder Coat Colors
Call for quote
Wood with Mirrored Interior
Glass
$893
Square
Radius
$148
End Panels Top Edge
3
4
Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 91
R&D
Service Candy/Chocolate Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels. • End panels have mirrored interior and are removable allowing multiple units to be connected in an endless series. • 1/4” thick tempered double bent curved glass with lift handle. • Rear access clear sliding doors. • Top to be 18 gauge stainless steel. • Two rows of protective 1” vinyl bumpers. • Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable 1/4” thick tempered glass shelves and 18 gauge steel deck pans are easily removable. • Five standard shelves on all models, extra shelves are optional. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch. REFRIGERATION SYSTEM • Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. • Digital readout thermometer provided to verify cabinet temperature is maintained between 65º and 70ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 92
R&D
Service Candy/Chocolate Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
Euro Bakery 48” Candy 59” Candy 77” Candy
Dimensions* (inches) W D H 48 1/2" 41 1/2" 51 1/2" 59 1/2" 41 1/2" 51 1/2" 77 1/2” 41 1/2" 51 1/2"
BTUH @65ºF Evap 1500 2000 2500
Volts
Phase
Amps
120 120 120
1 1 1
4 4 4.5
*Dimensions include end panels. Each end panel is ¾”.
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, NSF, and UL standards. OPTIONAL ACCESSORIES • Powder coated interior and top. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Wire or sheet metal shelves in lieu of glass. • Rear access clear or mirrored sliding doors. • Front accent lighting. • Product enhancing lights. • End panels available in solid wood or glass. • Self contained refrigeration. • Available for glycol systems. • Condensate evaporation pan. • Cord set available in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 93
R&D
Service Candy/Chocolate Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels (white, black, or almond) optional colors available
• Interior to be powder coated steel. • Mirrored side panels are removable to allow for an endless line up. • Mirrored rear sliding doors. • Remote refrigeration with blower coil and solenoid • valve system all wired to standard refrigeration control. • Refrigerated merchandising area includes T-5 fluorescent lighting and five adjustable glass shelves with ticket molding. • 1/4” thick tempered double bent curved glass with lift handle. • 2 rows of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
Model Dimensions* (L x D x H) Crated Weight
2
3
1 Shown with accent light.
48” Candy Euro
59” Candy Euro
77” Candy Euro
48-1/2" x 41-1/2” x 51-1/2”
59-1/2" x 41-1/2” x 51-1/2”
77-1/2" x 41-1/2” x 51-1/2”
860 lbs
920 lbs
1,125 lbs
$25,996
$28,444
$32,713
List Price
*Dimensions include end panels. Each end panel is ¾”. Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications 1
Standard
Options
List Price
Exterior 2 Interior
White, Black, Almond Laminate Powder Coated Black
3
None
Other Laminate Colors Various Powder Coat Colors Accent Down-Lighting Mirror Laminate Accent Strip Stainless Steel Accent Strip Self-Contained Cord Set
Call for quote Call for quote $735 $79 $250 $3,240 $70
Accent
Refrigeration Electrical Connection
R&D Fixtures
Remote Junction Box
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 94
R&D
Self-Serve Refrigerated Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels. • End panels have mirrored interior and are removable allowing multiple units to be connected in an endless series. • Top to be 18 gauge stainless steel. • Two rows of protective 1” vinyl bumpers. • Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable 1/4” thick tempered glass shelves and 18 gauge steel deck pans are easily removable. • Three standard shelves on all models, extra shelves are optional. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch. REFRIGERATION SYSTEM • Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. • Digital readout thermometer provided to verify cabinet temperature is maintained between 38º and 40ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 95
R&D
Self-Serve Refrigerated Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
Euro Bakery 48” Self Serve Refrigerated 59” Self Serve Refrigerated 77” Self Serve Refrigerated
Dimensions* (inches) W D H 48 1/2" 41 1/2" 51 1/2" 59 1/2" 41 1/2" 51 1/2" 77 1/2” 41 1/2" 51 1/2"
BTUH @20°F Evap 4500 5500 6500
Volts
Phase
Amps
120 120 120
1 1 1
3.5 3.5 4
*Dimensions include end panels. Each end panel is ¾”.
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Powder coated interior and top. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Extra shelves. • Wire or sheet metal shelves in lieu of glass. • Front accent lighting. • Product enhancement bulbs. • End panels available in solid wood or glass. • Self contained refrigeration. • Available for glycol systems. • Cord set available in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 96
R&D
Self-Serve Refrigerated Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels (white, black, or almond)
2
optional colors available
• Interior to be powder coated steel. • Mirrored side panels are removable to allow for an endless line up. • Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. • Refrigerated merchandising area includes T-5 fluorescent lighting and three adjustable glass shelves with ticket molding. • 2 rows of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor. Model
3
1 Shown with accent light.
Dimensions* (L x D x H)
48” Self Serve Euro
59” Self Serve Euro
77” Self Serve Euro
48-1/2" x 41-1/2” x 51-1/2”
59-1/2" x 41-1/2” x 51-1/2”
77-1/2" x 41-1/2” x 51-1/2”
Crated Weight
865 lbs
930 lbs
1,030 lbs
List Price
$16,789
$20,009
$22,228
*Dimensions include end panels. Each end panel is ¾”. Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications 1
Standard
Options
List Price
Exterior 2 Interior
White, Black, Almond Laminate Powder Coated Black
3
None
Other Laminate Colors Various Powder Coat Colors Accent Down-Lighting Mirror Laminate Accent Strip Stainless Steel Accent Strip Self-Contained Cord Set
Call for quote Call for quote $735 $79 $250 $3,728 $70
Accent
Refrigeration Electrical Connection
R&D Fixtures
Remote Junction Box
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 97
R&D
Service Refrigerated Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels. • End panels have mirrored interior and are removable allowing multiple units to be connected in an endless series. • 1/4” thick tempered double bent curved glass with lift handle. • Rear access clear sliding doors. • Top to be 18 gauge stainless steel. • Two rows of protective 1” vinyl bumpers. • Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable 1/4” thick tempered glass shelves and 18 gauge steel deck pans are easily removable. • Three standard shelves on all models, extra shelves are optional. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch. REFRIGERATION SYSTEM • Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. • Digital readout thermometer provided to verify cabinet temperature is maintained between 38º and 40ºF. • Supplied with 1” drain. Condensate evaporation pan is available to eliminate the need for plumbing hookup.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 98
R&D
Service Refrigerated Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
Dimensions* (inches) W D H 48 1/2" 41 1/2" 51 1/2" 59 1/2" 41 1/2" 51 1/2" 77 1/2” 41 1/2" 51 1/2"
Euro Bakery 48” Service Refrigerated 59” Service Refrigerated 77” Service Refrigerated
BTUH @20°F Evap 2000 2500 3000
Volts
Phase
Amps
120 120 120
1 1 1
3.5 3.5 4
*Dimensions include end panels. Each end panel is ¾”.
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Powder coated interior and top. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Extra shelves. • Wire or sheet metal shelves in lieu of glass. • Rear access clear or mirrored sliding doors. • Front accent lighting. • Product enhancing lights. • End panels available in solid wood or glass. • Self contained refrigeration. • Available for glycol systems. • Cord set available in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 99
R&D
Service Refrigerated Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels (white, black, or almond) optional colors available
• Interior to be powder coated steel. • Mirrored side panels are removable to allow for an endless line up. • Mirrored rear sliding doors. • Remote refrigeration with blower coil and solenoid valve system all wired to standard refrigeration control. • Refrigerated merchandising area includes T-5 fluorescent lighting and three adjustable glass shelves with ticket molding. • 1/4” thick tempered double bent curved glass with lift handle. • 2 rows of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor. Model
2
3
1 Shown with accent light.
48” Service Refrig Euro 59” Service Refrig Euro 77” Service Refrig Euro
Dimensions* (L x D x H)
48-1/2" x 41-1/2” x 51-1/2”
59-1/2" x 41-1/2” x 51-1/2”
77-1/2" x 41-1/2” x 51-1/2”
Crated Weight
850 lbs
910 lbs
1,115 lbs
List Price
$22,956
$26,111
$29,048
*Dimensions include end panels. Each end panel is ¾”. Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Accent
Standard
1
White, Black, Almond Laminate Powder Coated Black
3
None
Exterior 2 Interior
Refrigeration Electrical Connection
R&D Fixtures
Remote Junction Box
Options
Other Laminate Colors Various Powder Coat Colors Accent Down-Lighting Mirror Laminate Accent Strip Stainless Steel Accent Strip Self-Contained Cord Set
List Price
Call for quote Call for quote $735 $79 $250 $3,325 $70
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 100
R&D
Service Dry Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels. • End panels have mirrored interior and are removable allowing multiple units to be connected in an endless series. • 1/4” thick tempered double bent curved glass with lift handle. • Rear access clear sliding doors. • Top to be 18 gauge stainless steel. • Two rows of protective 1” vinyl bumpers. • Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable 1/4” thick tempered glass shelves are easily removable. • Deck to be laminated plywood, stainless steel available. • Three standard shelves on all models, extra shelves are optional. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 101
R&D
Service Dry Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
Dimensions* (inches) W D H 48 1/2" 41 1/2" 51 1/2" 59 1/2" 41 1/2" 51 1/2" 77 1/2” 41 1/2" 51 1/2"
Euro Bakery 48” Service Dry 59” Service Dry 77” Service Dry
Volts
Phase
Amps
120 120 120
1 1 1
2.5 2.5 3
*Dimensions include end panels. Each end panel is ¾”.
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Powder coated interior and top. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Extra shelves. • Wire or sheet metal shelves in lieu of glass. • Rear access clear or mirrored sliding doors. • Front accent lighting. • Product enhancing lights. • End panels available in solid wood or glass. • Cord set available in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 102
R&D
Service Dry Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels (white, black, or almond) optional colors available • Interior to be powder coated steel. • Mirrored side panels are removable to allow for an endless line up. • Mirrored rear sliding doors. • Dry merchandising area includes T-5 fluorescent lighting and three adjustable glass shelves with ticket molding. • 1/4” thick tempered double bent curved glass with lift handle. • 2 rows of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
Model
2
3
1 Shown with accent light.
Dimensions* (L x D x H)
48” Service Dry Euro
59” Service Dry Euro
77” Service Dry Euro
48-1/2" x 41-1/2” x 51-1/2”
59-1/2" x 41-1/2” x 51-1/2”
77-1/2" x 41-1/2” x 51-1/2”
Crated Weight
575 lbs
710 lbs
915 lbs
List Price
$16,865
$18,094
$19,508
*Dimensions include end panels. Each end panel is ¾”. Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications 1
Standard
Options
List Price
Exterior 2 Interior
White, Black, Almond Laminate Powder Coated Black
3
None
Other Laminate Colors Various Powder Coat Colors Accent Down-Lighting Mirror Laminate Accent Strip Stainless Steel Accent Strip Cord Set
Call for quote Call for quote $735 $79 $250 $70
Accent
Electrical Connection
R&D Fixtures
Junction Box
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 103
R&D
Self Serve Donut/Pastry Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels. • End panels have mirrored interior and are removable allowing multiple units to be connected in an endless series. • Acrylic lift-up segmented doors across front. • Rear access clear sliding doors. • Top to be 18 gauge stainless steel. • Two rows of protective 1” vinyl bumpers. • Unit must be leveled plumb at time of installation. • Fixture is designed to NEC, UL, and NSF standards. • Warranty is one year parts and labor. SHELVING • Adjustable 1/4” thick tempered glass shelves are easily removable. • Deck to be laminated plywood, stainless steel available. • Three standard shelves on all models, extra shelves are optional. • Full height shelf support pilasters with slotted holes on 1” centers for vertical shelf adjustments. • Brackets allow shelf to be adjusted to 3 different angles to increase visibility. • Fluorescent lights illuminate shelf area below and come with integral ballasts, shatter shields, and a separate on/off switch.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 104
R&D
Self Serve Donut/Pastry Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
Euro Bakery 48” Self Serve Pastry 59” Self Serve Pastry 77” Self Serve Pastry
Dimensions* (inches) W D H 48 1/2" 41 1/2" 51 1/2" 59 1/2" 41 1/2" 51 1/2" 77 1/2” 41 1/2" 51 1/2"
Volts
Phase
Amps
120 120 120
1 1 1
2.5 2.5 3
*Dimensions include end panels. Each end panel is ¾”.
ELECTRICAL REQUIREMENTS • Unit is pre-wired and furnished with a junction box for use on a dedicated 120V, 60Hz, 1 phase circuit. • All units built in strict accordance with all applicable NEC, UL, and NSF standards. OPTIONAL ACCESSORIES • Powder coated interior and top. • Assorted colors available for laminate, vinyl bumper, and powder coat. • Extra shelves. • Wire or sheet metal shelves in lieu of glass • Stainless or mirrored laminate accent strip. • Rear access clear or mirrored sliding doors. • Front accent lighting. • Product enhancing lights. • End panels available in solid wood or glass. • Cord set available in lieu of junction box.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 105
R&D
Self Serve Donut/Pastry Euro Series Bakery Case
FIXTURES
A Division of COYOD, LLC.
STANDARD FEATURES • Unit built with 14 gauge steel frame and finished in high pressure laminated exterior panels (white, black, or almond) optional colors available
• Interior to be powder coated steel. • Mirrored side panels are removable to allow for an endless line up. • Mirrored rear sliding doors. • Dry merchandising area includes T-5 fluorescent lighting and three adjustable glass shelves with ticket molding. • Acrylic lift-up segmented doors across front. • 2 rows of protective vinyl bumper. • Unit is pre-wired and furnished with a junction box for use on a dedicated 120/208V, 60Hz, 1 phase circuit. • Built in accordance with NEC, UL, and NSF standards. • Contact factory for assorted finishes, bar accessories, and alternative configurations. • Warranty is one year parts and labor.
2
3
1
Shown with accent light.
Model
48” Donut Euro
59” Donut Euro
77” Donut Euro
Dimensions* (L x D x H)
48-1/2" x 41-1/2” x 51-1/2”
59-1/2" x 41-1/2” x 51-1/2”
77-1/2" x 41-1/2” x 51-1/2”
Crated Weight
565 lbs
700 lbs
905 lbs
List Price
$22,238
$25,790
$25,175
*Dimensions include end panels. Each end panel is ¾”. Price does not include crating or shipping. Lead time is 6-8 weeks. Terms: FOB Mount Juliet, TN.
Product Specifications
Standard
1
White, Black, Almond Laminate Powder Coated Black
3
None
Exterior 2 Interior Accent
Electrical Connection
R&D Fixtures
Junction Box
Options
Other Laminate Colors Various Powder Coat Colors Accent Down-Lighting Mirror Laminate Accent Strip Stainless Steel Accent Strip Cord Set
List Price
Call for quote Call for quote $735 $79 $250 $70
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 106
R&D
Point of Sale Merchandiser
FIXTURES
A Division of COYOD, LLC.
SPECIFICATIONS / FEATURES CABINET • Front, end panels and all edges to consist of 3/4” plywood panels finished in high pressure plastic laminate (white, black or almond) optional colors available • Slot wall with black metal inserts and sloped shelves with plexi glass front to secure merchandise. • Adjustable glass shelves. • 5” toe kick finished with high pressure plastic laminate. • Protective 1” vinyl bumpers and corner guards • Contact factory for assorted finishes and alternative configurations. • Fixture is designed to NEC and UL standards. • Warranty is one year parts and labor. OPTIONAL ACCESSORIES • Assorted colors available for laminate, slot wall, and vinyl bumper. • Can be finished in stainless steel. • Available with casters in lieu of toe kick. • Canopy lighting. • Accent lighting. • Multiple configurations and sizes available.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 107
R&D
Point of Sale Merchandiser
FIXTURES
A Division of COYOD, LLC.
Point of Sale Merchandisers P.O.S.
R&D Fixtures
Dimens ions (L x D x H) 24” x 36” x 48”
L is t P rice
$5,966
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 108
R&D
End Display
FIXTURES
A Division of COYOD, LLC.
*Shown with optional finishes. SPECIFICATIONS / FEATURES CABINET • Front, end panels and all edges to consist of 3/4” plywood panels finished in high pressure plastic laminate (white, black or almond) optional colors available • Window end panels. • Seven sloped shelves per opening with tag molding. • 5” toe kick finished with high pressure plastic laminate. • Protective 1” vinyl bumpers and corner guards • Contact factory for assorted finishes and alternative configurations. • Fixture is designed to NEC and UL standards. • Warranty is one year parts and labor. OPTIONAL ACCESSORIES • Assorted colors available for laminate, slot wall, and vinyl bumper. • Can be finished in stainless steel. • Available with casters in lieu of toe kick. • Canopy lighting. • Multiple configurations and sizes available.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 109
R&D
End Display
FIXTURES
A Division of COYOD, LLC.
End Display Merchandisers End Display
R&D Fixtures
Dimens ions (L x D x H) 48” x 30” x 81”
L is t P rice
$11,236
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 110
R&D
Cash Counters
FIXTURES
A Division of COYOD, LLC.
Modular Components now available. Customize your own cash counter, or contact us for various configurations. SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Front, end panels, and all edges to consist of 3/4” plywood panels finished in high pressure plastic laminate. • Each module component features adjustable shelving. • One door and/or drawer per 2’ section. • 5-1/2” high black toe-kick base. • Fixture is designed to NEC and UL standards. • Warranty is one year parts and labor. OPTIONS • Unlimited configurations and finishes.
*Pictures and renderings shown with optional features.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 111
R&D
Cash Counters
FIXTURES
A Division of COYOD, LLC.
Shell Module
Cash Module Shell 2’ Shell Module 4’ Shell Module 6’ Shell Module 8’ Shell Module Cash Module with Door(s) 2’ Door Module 4’ Door Module 6’ Door Module 8’ Door Module Drawer Module
Dimensions (inches) W D H 24 36 34 48 36 34 72 36 34 96 36 34
Dimensions (inches) W D H 24 36 34 48 36 34 72 36 34 96 36 34
$2,328 $3,062 $3,682 $4,133
Door Module List Price $2,719 $3,943 $4,840 $5,471
(1) DRAWER OR (1) DOOR PER 2’ SECTION Dimensions (inches) W D H 24 36 34 48 36 34 72 36 34 96 36 34
Cash Module with Drawer(s) 2’ Drawer Module 4’ Drawer Module 6’ Drawer Module 8’ Drawer Module 45° Wedge Module
Optional Top
Corian
CaesarStone
2’ Module 4’ Module 6’ Module 8’ Module
$566 $1,149 $1,732 $2,373
$471 $1,039 $1,667 $2,206
R&D Fixtures
List Price
45° Wedge
Dimensions (inches) W D H 24
36
34
List Price $3,116 $3,992 $4,661 $5,558
List Price $1,980
R&D Module
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 112
R&D
Floral Display Cases
FIXTURES
A Division of COYOD, LLC.
Four Section Floral Display *Available in modular components
2 Rows of Bumper
Available in limitless configurations, please contact factory for more options.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 113
R&D
Floral Display Cases
FIXTURES
A Division of COYOD, LLC.
Refrigerated Floral Display
Sectional Floral Display
SPECIFICATIONS / FEATURES BASE CABINET CONSTRUCTION • Front, end panels, and all edges to consist of 3/4” plywood panels finished in high pressure plastic laminate. • 5-1/2” high black toe-kick base. • Fixture is designed to NEC and UL standards. • Warranty is one year parts and labor. OPTIONAL ACCESSORIES • Assorted colors available for laminate, vinyl bumper and toe kick. • Accent strips and lighting. • Casters in lieu of toe-kick base. Model Dimensions (L x D x H)
4’ Floral Display Section
Floral Display Mitered End
Refrigerated Floral Case
48" x 36” x 34”
66" x 36” x 34”
72" x 36” x 94”
$3,100
$4,150
$34,345
List Price
R&D Fixtures
(Premium Series)
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 114
R&D
Custom Millwork
FIXTURES
A Division of COYOD, LLC.
Offering Custom Millwork with the ability to meet all your display and merchandising needs.
Custom displays
Service side features sliding doors
*Glass displays available in modular components.
W hatever your requirements, R&D is committed to providing the best equipment in the industry. R&D Fixtures begins with an in-depth understanding of your needs and goals.
Our design department works with you, to ensure you get the right model for your specific needs.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 115
R&D
2SWLRQV
FIXTURES
A Division of COYOD, LLC.
Canopies
Standard Wood Canopy with Lift Up Glass
Clear View Canopy with Fixed Glass
Clear View Canopy with Lift Up Glass
Powder coated canopies available.
Cold Pans
Sloped Coppered Cold Pan
Flat Coppered Cold Pan
Air Over Cold Pan
Bases
Standard Wood Base
R&D Fixtures
Stainless Steel Base* *Up Charge Applies.
Legs with Removable Toe-kick
Legs
Casters
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 116
R&D
2SWLRQV
FIXTURES
A Division of COYOD, LLC.
Bar Accessories
Tray Slide Utensil Holders Plate Dispensers Cup Dispensers Napkin Dispensers Product Enhancement Bulbs
Call for quote $39 each Call for quote $269 each $494 each Call for quote
Food Pans, Lids, and Serving Utensils
$55 each $55 each $28 each $22 each $17 each $72 each $44 each $39 each $33 each $28 each $55 each $33 each $22 each $22 each $11 each $17 each $17 each $17 each $55 each $66 each $33 each $44 each $11 each
2-1/2” Deep Full Size Inset Pans 2-1/2” Deep Half Size Inset Pans 2-1/2” Deep Third Size Inset Pans 2-1/2” Deep Quarter Size Inset Pans 2-1/2” Deep Ninth Size Inset Pans 4” Deep Full Size Inset Pans 4” Deep Half Size Inset Pans 4” Deep Third Size Inset Pans 4” Deep Quarter Size Inset Pans 4” Deep Ninth Size Inset Pans Full Size Pan Lids Half Size Pan Lids Third Size Pan Lids Quarter Size Pan Lids Ninth Size Pan Lids Salad Dressing Templates Serving Spoons Tongs 7qt Soup Inserts 11qt Soup Inserts 7qt Soup Lids 11qt Soup Lids Soup Ladles
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 117
R&D
WARRANTY, TERMS & CONDITIONS
FIXTURES
A Division of COYOD, LLC.
Warranty; Remedies; Limitations R&D Fixtures warrants its products to be free of defects in materials under normal use and service for a period of (1) year parts and labor from the date of delivery. Refrigeration compressors will be warranted for a period of (12) months, optional four (4) year warranty is available. This warranty is extended to the original purchasers only. It does not cover wear or parts such as plastic tongs, tong holders, tong cords, bag holders, acrylic dividers or roll bins. (R&D Fixtures highly recommends warm water and a mild unscented dishwashing liquid for cleaning all acrylic materials.) R&D Fixtures liability for any defects in the goods shall not exceed the purchase price of goods. R&D Fixtures shall have no liability to the purchaser for consequential damages of any kind whatsoever, including but not limited to, personal injury, property damage, lost profits or other economic injury due to any defect in the goods or breach by R&D Fixtures. R&D Fixtures shall not be liable to the purchaser in tort for any negligent design or manufacture of the goods, or for the omission of any warning there from. R&D Fixtures shall have no obligation or liability under this warranty for claims arising from any other party’s (including purchaser’s) negligence or misuse of the goods or environmental conditions. This warranty does not apply to any claim or damage arising for or caused by improper storage, handling, installation, maintenance, electrical problems, or from fire, flood, accidents, structural defects, building settlement or movement, acts of God, or other causes beyond R&D. A. All service labor and/or parts charges are subject to approval by R&D Fixtures. All claims must have the following information attached: The serial number. Date and place of installation. The name of the contractor who performed the installation. A detailed description of the equipment failure and all circumstances relating to the failure. B. Once a claim has been determined to be a true warranty claim by R&D Fixtures the following procedures will be taken: Replacement parts will be sent free of charge from R&D Fixtures on a freight prepaid basis. Reimbursement for a service labor will be paid when the following conditions have been met: a. Prior approval was given to the service company by R&D Fixtures. b. An itemized statement of all labor charges incurred is received by R&D Fixtures. All time will be reimbursed based on straight time rates and reasonable time for repair of the defect. C. If any equipment is altered without the written consent of R&D Fixtures, the warranty becomes null and void. Acts of God are not to be considered under this warranty. D. R&D Fixtures will not be liable for any default or delay in performance here under caused by any contingency beyond its control, including but not limited to Government restrictions, acts of war, material shortage, labor disputes, fire, flood, or any other acts of God. E. Warranty merchandise shall not be returned without first securing written authorization from R&D Fixtures directly. F. This warranty does not include transportation charges to or from R&D Fixtures, any food or business loss, any equipment located outside of the United States: unless other terms were previously arranged or negotiated, or any defect or equipment failure which results from misuse, damage in transit, accident, electrical problems, or alteration of the equipment. G. R&D Fixtures makes no other expressed or implied warranties for a particular purpose or merchantability. In no event shall R&D Fixtures be liable for special, incidental or consequential damages. Cancellation of Orders The purchaser may modify or cancel an order upon written notice, prior to that order being entered into production, subject to cancellation charges as determined by R&D Fixtures. Once an order is in the production cycle, completed or shipped, the buyer is liable for the full sale price. Prices and Terms of Payment Terms of sale upon approved credit are net for thirty (30) days from the date of quotation and are subject to stenographic error correction plus adjustment based on delivery requirements of the purchaser. In event of specification changes after the receipt of the purchasers’ order, R&D Fixtures may adjust the price to cover such charges. If at any time R&D Fixtures determines that a purchaser’s financial condition or credit rating does not merit a sale on credit, R&D Fixtures may require advance payment. A service charge of 1.5% per month, (or such lesser rates as may be the maximum permitted by law) will be assessed on all past due accounts. R&D Fixtures will be entitled to suspend performance under this or any other Agreement with purchaser until purchaser’s account is current. R&D Fixtures will be entitled to the payment of all expenses and reasonable attorney’s fees incurred in the collection of any delinquent account. Liability of Company R&D Fixtures shall not be liable to purchaser or to any purchases toward any third party for damages sustained arising directly or indirectly beyond the price paid by the purchaser of such merchandise. Delivery and Delay Risk of loss to the goods shall pass to purchaser upon delivery of the goods to the carrier. Shipping dates are estimates only. R&D Fixtures may ship all of the goods at one time or in portions. R&D Fixtures has the right to determine the method of shipment and routing. All deliveries are subject to modifications or cancellations due to events beyond the control of R&D Fixtures. If R&D Fixtures cannot control deliveries, then the estimated time of delivery will be extended accordingly and R&D Fixtures will not be held liable for any loss or profit or property, or for any direct, indirect, special, incidental, consequential or other damages caused by any delay or failure to deliver. If purchaser causes or requests delay in the manufacture, assembly, shipment or installation of goods, purchaser shall pay R&D Fixtures for all costs, losses and damage resulting there from, including but not limited to storage, interest, and insurance. Damages and Shortage Claims Damage claims for merchandise shipped by transit companies must be submitted to that carrier immediately and not to R&D Fixtures. Shortage of merchandise must be reported to R&D Fixtures within three work days of the receipt of goods.
R&D Fixtures
Built to meet the following regulatory specifications.
490 Industrial Drive Mt. Juliet, TN 37122 (888) 827-6820 • Fax (615) 758-1006
• www.rdfixtures.com
• sales@rdfixtures.com
Rev. 10.2010
Printed in U.S.A.
Based on operating conditions of 77°F and 55% relative humidity. Due to continuous improvements, specifications subject to change without notice.
Page 118
www.rdfixtures.com Toll Free: 888-827-6820 Fax: 615-758-1006 Email: sales@rdfixtures.com 490 Industrial Drive Mt. Juliet, TN 37122