O ring catalogue by Hai Le

0-RINGS be used with many media, including aggressive media, at both low temperatures and very high temperatures if an appropriate material is chosen. The information below is limited to the use of the O-ring as a static sealing element.

O-RINGS

The O-ring is the most widely used sealing element particularly for static duties but also, within limits, for dynamic duties. O-rings are not only used in hydraulic systems; they are used universally in almost all technical fields. They can

O-RINGS Round cord ring for universal application.

Installation and design information Housings for O-rings are generally recessed at right angles. The groove depth and groove width dimensions necessary depend on the particular cord diameter. If additional support rings are installed, the width of the groove has to be correspondingly increased. The dimensions are given in the dimension lists for O-ring housings. The volume of the housing in these lists is designed to be about 25% greater than that of the relevant O-ring. This is necessary because of the high thermal expansion, or possible swelling, of the elastomer. Depending on the type of housing, O-rings can be stretched or compressed without any adverse effect on their function. Surface finish Surface roughness

1,6 µm

6 µm

Non-pulsating Bottom of groove pressure

3,2 µm

12 µm

Groove flanks

6,3 µm

20 µm

Lead-in chamfer

0,6 µm

5 µm

Sealing surface

Pulsating Bottom of groove pressure Sealing surface

The O-ring retains its sealing effect by radial or axial deformation in the different types of housings. When subject to pressure, the O-ring is pressed and deformed against the groove flank away from the pressure. With increasing system pressure, the total sealing pressure force increases. O-RINGS

Selecting the correct O-ring dimension O-rings are subject to residual deformation (compressive set) caused by the loads and the associated material fatigue. O-rings of small cord diameter have a relatively high compression set therefore efforts should be made to use Orings with the largest possible cord diameter. The groove dimensions for the cord Ø d2 are given, as a function of the type of housing, in the "housing for O-rings" tables. The tables show the recommended cord diameter as a function of the diameters d and D.

Bore # d or D # 18 > 18... 30 > 30... 35 > 35... 45 > 45... 50 > 50... 63 > 63... 80 > 80... 100 > 100... 200 > 200... 250 > 250... 300 > 300... 400 > 400... 500 > 500

Recommended cord Ø d2 for bore Ø d1 or D 1,5 1,78 2 2,5 2,62 3 + +

• + +

+ + + +

+ + + + + +

+ • • • • +

+ + + + + + + +

+ = recommended dimensions • = preferred dimensions

3,5/ 3,53 + + + + + • • + +

+ + + +

5,33

5,7

+ + + +

• • • + +

+ + + +

+ + + + + +

6,99/ 7

+ • • • +

+ + + + +

+ + + + •

SURVEY OF THE HOUSING DIMENSIONS Housing sealing on the outside and inside, radial pressure Housing types 1 and 2 Cord Ă&#x2DC; d2

Groove depth t + 0,05

b2 + 0,25

Groove width b1 + 0,25

b2 + 0,25

Housing axially sealing, inward press. Housing type 3 Groove depth Groove width b + 0,25 t + 0,05

Radius R1 without support ring

Chamfer

with support ring

1,5

1,2

2,1

3,5

4,9

1,1

2,3

0,3

1,5

1,78

1,4

2,4

3,8

5,2

1,3

2,6

0,3

1,5

1,6

2,6

5,4

1,5

2,8

0,3

2,5

3,4

4,8

6,2

1,9

3,6

0,3

2,62

2,1

3,6

6,4

3,8

0,3

2,4

5,4

6,8

2,3

4,2

0,6

0,4

2,5

3,5

2,8

4,7

6,1

7,5

2,7

4,9

0,6

0,4

2,5

3,53

2,8

4,8

6,2

7,6

2,7

0,6

0,4

2,5

3,2

5,4

6,8

8,2

3,1

5,6

0,6

0,4

4,1

6,6

8,5

10,4

6,8

0,6

0,4

5,33

4,3

7,1

10,9

4,2

7,3

0,6

5,7

4,6

7,7

4,9

6,99

5,8

9,5

9,6

11,5

4,5

7,9

0,6

10,8

13,6

4,7

8,2

0,6

5,7

9,7

5,8

9,5

5,7

6,7

10,8

6,5

8,5

13,5

8,3

13,7

O-RINGS

Groove width: b = without support ring, b1 = with one support ring, b2 = with two support rings

O-rings, sealing on the outside, radial pressure (Housing type 1) In this type of housing, it is necessary to ensure that the O-ring rests firmly on the bottom of the groove. Stretching of the O-ring in the installed condition is permissible up to 6%.

O-rings, sealing on the inside, radial pressure (Housing type 2) In this type of housing, the outer periphery of the O-ring rests on the bottom of the groove. Compression of up to 3% is permissible.

O-rings, axially sealing, inward pressure (Housing type 3) In this type of housing, the "inward pressure" direction is the decisive factor in determining the Oring size. In the unpressurised condition, the O-ring must rest on the outer wall of the groove so that the O-ring does not move in the housing when pressure is applied.

O-RING MATERIALS The O-ring materials mainly used in hydraulics and general machinery are NBR of hardnesses 70, 80 and 90 Shore A and FPM of 70 Shore A. The OR O-ring series gives the reference numbers for O-rings in these materials on pages 183 to 210. Enquiries about the reference numbers for other materials should be made to us.

Additional tools O-rings for which no reference number is listed in the OR series and O-rings in other materials, can be produced from tools which are indicated by N, M, H or S in the dimension lists. Depending on the shrinkage behaviour of the individual material and the particular tool design, dimensional differences relative to the nominal dimension quoted in the series can occur. These dimensional differences are given in the tables for each tool design as a percentage relative to the nominal dimension quoted in the series.

Material hardness The hardness of the O-ring material to be selected depends on the system pressure, the tolerances involved in the design and the associated gap widths. It should be remembered that the gap width can be increased by the elastic strain of the metallic materials.

Dimensional differences (%) for various tool designs

Radial gap widths

Material N

Maximum gap width (mm) for material hardness (shore A) 70 80 90

Pressure (bar) 60

0,2

> 60...100

0,1

0,2

> 100...160

0,1

0,2

> 160

0,1

NBR 70,

In the case of larger gap widths, the O-ring should be protected against gap extrusion by support rings.

Design of additional tools M H

-0,1 ...+0,4 +0,5...+1,0 +1,1...+1,5 +1,6...+2,1

NBR 80,

-0,2 ...+0,3 +0,4...+0,9 +1,0...+1,4 +1,5...+2,0

NBR 90,

-0,3 ...+0,2 +0,3...+0,8 +0,9...+1,3 +1,4...+1,9

FPM 70,

-1,3 ... - 0,8

- 0,7... - 0,2

NBR 60,

-0,7 ... - 0.2

- 0,1...+0,4 +0,5...+0,9 +1,0...+1,5

- 0,1...+0,3 +0,4...+0,9

NBR 75,

-0,4 ...+0,1 +0,2...+0,7 +0,8...+1,2 +1,3...+1,8

FPM 75,

-1,8 ... - 1,3

- 1,2... - 0,7

FPM 90,

-1,2 ... - 0,7

- 0,6... - 0,1

0,0...+0,4 +0,5...+1,0

Material Shore A

Temperature o C

Media

NBR 70, I

- 30...+100

NBR 80, I

- 25...+100

Hydraulic oil, grease, water, emulsions (HF-A, HF-B, HF-C)

- 0,6... - 0,2

- 0,1...+0,4

Shape and surface variations O-rings are manufactured within the limits of permissible shape and surface given in DIN 3771, Part 4 and ISO 3601/III Type Characteristic N.

Application limits

O-RINGS

Tolerances The permissible tolerances for the inner and cord diameters are standardised in DIN 3771, Part 1 and ISO 3601/I. They are designed for O-rings in nitrile-butadine rubber (NBR). See page 148 for tolerance tables. In the case of other materials and hardnesses, there may be differences because of the different shrinkage behaviour of the materials. These have no substantial effect on the sealing function of the O-ring in static applications.

NBR 90,

- 20...+100

NBR 60,

- 55...+ 80

NBR 75,

- 55...+ 80

FPM 79,

- 10...+200

FPM 90,

- 10...+200

FPM 75,

- 10...+200

Hydraulic oil, grease, HF-D, very good chemical resistance Especially methanol, fuel

*Material for O-rings with inner Ø d1>200mm, with the exception of articles indicated by "B". The temperatures quoted are limiting values which must always be considered in association with the medium to be sealed and the particular system pressure.

Examples for calculating the dimensional difference See ORseries page

Nominal dimension Inner Cord Ø d1 Ø d2

Tool design

Material

Dimensional difference up to

Effective dimension Inner Inner Ø d1 up to Ø d1

Effective dimension Cord Cord Ø d2 up to Ø d2

187

20,22

3,53

NBR 60

- 0,7% ... - 0,2%

20,08 ... 20,18

3,51 ... 3,52

195

NBR 75

+0,2% ... +0,7%

19,18 ... 90,63

5,01 ... 5,04

196

114

FPM 75

- 0,6% ... - 0,2%

113,32 ...113,77

5,96 ... 5,99

206

380,37

5,33

FPM 90

+0,5% ... +1,0%

382,27 ...384,17

5,36 ... 5,38

TOLERANCES TO DIN 3771, PART 1 AND ISO 3601/I Tol. ±0,13 ±0,14 ±0,15 ±0,16 ±0,17 ±0,18 ±0,19 ±0,20 ±0,21 ±0,22 ±0,23 ±0,24 ±0,25 ±0,26 ±0,28 ±0,29 ±0,31 ±0,32 ±0,33 ±0,34 ±0,35 ±0,36 ±0,37 ±0,38 ±0,39 ±0,40 ±0,41 ±0,42 ±0,43 ±0,44 ±0,45 ±0,46 ±0,47 ±0,48 ±0,50 ±0,51 ±0,52 ±0,54 ±0,55 ±0,56 ±0,58

Inner Ø d1 67,0 ... 68,99 69,0 ... 70,99 71,0 ... 72,99 73,0 ... 74,99 75,0 ... 77,49 77,5 ... 79,99 80,0 ... 82,49 82,5 ... 84,99 85,0 ... 87,49 87,5 ... 89,99 90,0 ... 92,49 92,5 ... 94,99 95,0 ... 97,49 97,5 ... 99,99 100 ... 102,9 103 ... 105,9 106 ... 108,9 109 ... 111,9 112 ... 114,9 115 ... 117,9 118 ... 121,9 122 ... 124,9 125 ... 127,9 128 ... 131,9 132 ... 135,9 136 ... 139,9 140 ... 144,9 145 ... 149,9 150 ... 154,9 155 ... 159,9 160 ... 164,9 165 ... 169,9 170 ... 174,9 175 ... 179,9 180 ... 184,9 185 ... 189,9 190 ... 194,9 195 ... 199,9 200 ... 205,9 206 ... 211,9 212 ... 217,9

Inner Ø d1 218 ... 223,9 224 ... 229,9 230 ... 235,9 236 ... 242,9 243 ... 249,9 250 ... 257,9 258 ... 264,9 265 ... 271,9 272 ... 279,9 280 ... 289,9 290 ... 299,9 300 ... 306,9 307 ... 314,9 315 ... 324,9 325 ... 334,9 335 ... 344,9 345 ... 354,9 355 ... 364,9 365 ... 374,9 375 ... 386,9 387 ... 399,9 400 ... 411,9 412 ... 424,9 425 ... 436,9 437 ... 449,9 450 ... 461,9 462 ... 474,9 475 ... 486,9 487 ... 499.9 500 ... 514,9 515 ... 529,9 530 ... 544,9 545 ... 559,9 560 ... 579,9 580 ... 599,9 600 ... 614,9 615 ... 629,9 630 ... 649,9 650 ... 669,9 670 ... 689.9 690

Tol. ±0,59 ±0,61 ±0,63 ±0,64 ±0,66 ±0,67 ±0,69 ±0,71 ±0,73 ±0,75 ±0,77 ±0,79 ±0,81 ±0,83 ±0,84 ±0,87 ±0,89 ±0,91 ±0,93 ±0,95 ±0,97 ±1,00 ±1,03 ±1,05 ±1,08 ±1,10 ±1,13 ±1,17 ±1,20 ±1,24 ±1,27 ±1,31 ±1,34 ±1,38 ±1,41 ±1,44 ±1,48 ±1,51 ±1,55 ±1,59 ±1,63

Tol. ±1,67 ±1,71 ±1,75 ±1,79 ±1,83 ±1,88 ±1,93 ±1,98 ±2,02 ±2,08 ±2,14 ±2,21 ±2,25 ±2,30 ±2,37 ±2,43 ±2,49 ±2,56 ±2,62 ±2,68 ±2,76 ±2,84 ±2,91 ±2,99 ±3,07 ±3,15 ±3,22 ±3,30 ±3,37 ±3,45 ±3,54 ±3,63 ±3,72 ±3,81 ±3,93 ±4,05 ±4,13 ±4,22 ±4,34 ±4,46 ±0,65%

Cord Ø d2 2,62 >2,62 ... 3,0 >3,00 ... 4,5 >4,50 ... 5,5 >5,50 ... 7,5 >7,50 ... 8,5 >8,50 ... 10,0

Tol. ±0,08 ±0,09 ±0,10 ±0,13 ±0,15 ±0,18 ±0,20

Extract from DIN 3771, Part 1, 12.84 edition Reproduced with permission of DIN, Deutsches Institut für Normung e.V. The standard should be used in the version with the latest eddition date, which can be obtained from Beuth Verlag GMBH, Burggrafenstraße 6, 1000 Berlin 30.

O-RINGS

Inner Ø d1 1,8 ... 2,79 2,8 ... 4,86 4,87 ... 6,69 6,7 ... 8,75 8,76 ... 10,59 10,6 ... 11,79 11,8 ... 14,99 15,0 ... 16,99 17,0 ... 18,99 19,0 ... 21,19 21,2 ... 22,39 22,4 ... 24,99 25,0 ... 25,79 25,8 ... 27,99 28,0 ... 29,99 30,0 ... 31,49 31,5 ... 32,49 32,5 ... 34,49 34,5 ... 35,49 35,5 ... 36,49 36,5 ... 37,49 37,5 ... 38,69 38,7 ... 39,99 40,0 ... 41,19 41,2 ... 42,49 42,5 ... 43,69 43,7 ... 44,99 45,0 ... 46,19 46,2 ... 47,49 47,5 ... 48,69 48,7 ... 49.99 50,0 ... 51,49 51,5 ... 52,99 53,0 ... 54,49 54,5 ... 55,99 56,0 ... 57,99 58,0 ... 59,99 60,0 ... 61,49 61,5 ... 62,99 63,0 ... 64,99 65,0 ... 66,99

PHYSICAL AND CHEMICAL PROPERTIES OF O-RING MATERIALS Physical and chemical properties Density

NBR 70

DIN 53479

g/cm3

NBR 80

NBR 90

FPM 70

NBR 60 NBR 75 FPM 75 FPM 90

1,23 1,20 1,32 1,22 1,31 1,25 1,90 1,85 1,18 1,21 1,92 1,87 ±0.02 ±0,02 ±0,02 ±0,02 ±0,02 ±0,02 ±0,02 ±0,02 ±0,02 ±0,02 ±0,02 ±0,02

Hardness

DIN 53505

Hardness

DIN 53519

Shore A 70±5 IRHD

Tensile strength

DIN 53504

N/mm2

10,5

17,5

15,5

Ultimate elongation

DIN 53504

280

250

280

250

160

200

140

150

280

180

200

120

Tensile stress at 100% elongation

DIN 53504

N/mm2

4,4

6,3

6,5

11,9

8,8

5,7

4,3

6,6

5,5

Resistance to tear propagation

DIN 53515

N/mm2

13,5

Low temperature reference value TR

DIN 53520

-22

-26

-20

-15

-20

-12

-50,5

-45

Brittle point TS

DIN 53546

-50

-35

-25

-30

-25

-30

-65

-60

-25

168 h/100OC

-5

-5,4

-5,3

-1,7

-3,5

-2,6

-10

-3

+11

+13

+16

+12,5

+35

73±5

70±5 80±5 78±5

88±5 86±5 70±5 70±5 60±5 73±5 72±5

70±5 84±5 78±5

89±5 87±5 70±5 69±5 62±5 73±5 74±5

Volumetric change ASTM oil I

ASTM oil III

70 h/150 C

ASTM oil III

168 h/100OC

70 h/200OC

Service fluid No. 101

+1,8

+9,5

+10

-2

±0

-7

-6

+1,7

Hardness change ASTM oil I

168 h/100OC

Points

ASTM oil III

70 h/150OC

Points

ASTM oil III Service-Fluid Nr.101

168 h/100 C

Points

70 h/200OC

Points

+5 -6

+1 -8

+5 -3

+2 -12

-5

-10

+3 -3

-14

-1

-15 -7

Residual compressive set 24 h/ 70OC

DIN 53517

70 h/100OC

DIN 53517

70 h/200 C

DIN 53517

24 h/ 70OC

ASTM-D 395 B

O-RINGS

70 h/100 C

ASTM-D 395 B

70 h/200OC

ASTM-D 395 B

10 20

* Material for O-rings with inside Ø d1> 200 mm, with the exception of articles marked with "B".

O-RING MACHINING

GLAND - DYNAMIC

FACE - STATIC

GROOVE SIZES DYNAMIC APPLICATIONS PNEUMATICS

GROOVE SIZES DYNAMIC APPLICATIONS HYDRAULICS CROSS SEC. mm

1 1.5 1.6 1.78 1.9 2 2.4 2.5 2.62 2.7 3 3.5 3.53 3.6 4 4.5 5 5.33 5.5 5.7 6 6.5 6.99 7 7.5 8 8.4 8.5 9 9.5 10

0.9 1.3 1.4 1.5 1.6 1.7 2.1 2.2 2.3 2.4 2.6 3.1 3.1 3.2 3.5 4 4.45 4.7 4.95 5.1 5.4 5.8 6.3 6.3 6.7 7.2 7.6 7.7 8.2 8.6 9.1

STATIC APPLICATIONS

CROSS SEC. mm

1.3 1.9 2 2.3 2.4 2.4 2.9 3 3.1 3.2 3.6 4.2 4.2 4.3 4.8 5.4 6 6.4 6.6 6.9 7.2 7.8 8.4 8.4 9 9.6 10.1 10.2 10.8 11.4 12

1 1.5. 1.6 1.78 1.9 2 2.4 2.5 2.62 2.7 3 3.5 3.53 3.6 4 4.5 5 5.33 5.5 5.7 6 6.5 6.99 7 7.5 8 8.4 8.5 9 9.5 10

0.95 1.35 1.45 1.55 1.75 1.8 2.15 2.25 2.35 2.45 2.75 3.25 3.25 3.35 3.7 4.2 4.65 4.95 5.15 5.35 5.65 6.1 6.6 6.6 7.1 7.6 7.9 8 8.5 9 9.5

1.3 1.9 2 2.3 2.4 2.4 2.9 3 3.1 3.2 3.6 4.2 4.2 4.3 4.8 5.4 6 6.4 6.6 6.9 7.2 7.8 8.4 8.4 9 9.6 10.1 10.2 10.8 11.4 12

CROSS SEC. mm

1 1.5 1.6 1.78 1.9 2 2.4 2.5 2.62 2.7 3 3.5 3.53 3.6 4 4.5 5 5.33 5.5 5.7 6 6.5 6.99 7 7.5 8 8.4 8.5 9 9.5 10

0.8 1.1 1.2 1.3 1.4 1.5 1.8 1.9 2 2.1 2.3 2.7 2.7 2.8 3.15 3.6 4 4.3 4.5 4.65 4.95 5.4 5.85 5.85 6.3 6.75 7.15 7.25 7.7 8.2 8.65

1.3 1.9 2.1 2.3 2.4 2.6 3.1 3.2 3.4 3.5 3.9 4.5 4.5 4.7 5.2 5.8 6.5 6.9 7.1 7.4 7.8 8.4 9.1 9.1 9.7 10.4 10.9 11 11.7 12.3 13

When using back-up rings "B" should be increased by width of the back-up ring. POUNDS PER SQUARE INCH 100

200

300

400

600

800

1000 1500 2000 3000 4000 5000 6000

WITH BACK-UP RING

.036

.032

.028

.026

.024

.021

.018

.014

.010

WITHOUT BACK-UP RING

.031

.025

.022

.018

.014 .010

.007

.004

.002

.006

.004

.003

.002

O-RINGS

PISTON - DYNAMIC

IMPERIAL O-RINGS N70 : N90 : VITON : EPDM : QUAD : NEOPRENE : SILICONE

O-RINGS

001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050

ACTUAL MILIMETERS

NOMINAL INCHES

ARP PART # ID

X SEC

+/-

1/32 3/64 1/16 5/64 7/64 1/8 5/32 3/16 7/32 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.1/2 1.5/8 1.3/4 1.7/8 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/4 3.1/2 3.3/4 4 4.1/4 4.1/2 4.3/4 5 5.1/4

3/32 9/64 3/16 13/64 15/64 1/4 9/32 5/16 11/32 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/18 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 1.5/8 1.3/4 1.7/8 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/8 3.3/8 3.5/8 3.7/8 4.1/8 4.3/8 4.5/8 4.7/8 5.1/8 5.1/8

1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/6 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16

0.74 1.07 1.42 1.78 2.57 2.90 3.68 4.47 5.28 6.07 .65 9.25 10.82 12.42 14.00 15.60 17.17 18.77 20.35 21.95 23.52 25.12 26.70 28.30 29.87 31.47 33.05 34.65 37.82 41.00 44.17 47.37 50.52 53.67 56.87 60.05 63.22 66.40 69.57 72.75 75.92 82.27 88.62 94.97 101.34 107.70 114.00 120.40 126.76 133.07

1.02 1.27 1.52 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.18 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78 1.78

.08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08

IMPERIAL O-RINGS N70 : N90 : VITON : EPDM : QUAD : NEOPRENE : SILICONE

X SEC

+/-

1/16 3/32 1/18 5/32 3/16 7/32 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 1.9/16 1.5/8 1.11/16 1.3/4 1.13/16 1.7/8 1.15/16 2 2.1/16 2.1/8 2.3/16 2.1/4 2.5/16 2.3/8 2.7/16 2.1/2 2.9/16 2.5/8 2.11/16 2.3/4 2.13/16 2.7/8 3

1/4 9/32 5/16 11/32 3/8 13/32 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 1.9/16 1.5/8 1.11/16 1.3/4 1.13/16 1.7/8 1.15/16 2 2.1/16 2.1/8 2.3/16 2.1/4 2.5/16 2.3/8 2.7/16 2.1/2 2.9/16 2.5/8 2.11/16 2.3/4 2.13/16 2.7/8 2.15/16 3 3.1/16 3.3/16

3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32

1.24 2.06 2.84 3.63 4.42 5.23 6.02 7.59 9.19 10.77 12.37 13.94 15.54 17.12 18.72 20.29 21.89 23.47 25.07 26.64 28.24 29.82 31.42 32.99 34.59 36.17 37.77 39.34 40.94 42.52 44.12 45.69 47.29 48.90 50.47 52.07 53.64 55.25 56.82 58.42 60.00 61.60 63.17 64.77 66.34 67.95 69.52 71.12 72.69 75.87

2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62

.08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08

O-RINGS

102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151

ACTUAL MILIMETERS

NOMINAL INCHES

ARP PART #

IMPERIAL O-RINGS N70 : N90 : VITON : EPDM : QUAD : NEOPRENE : SILICONE ACTUAL O-RING CROSS SECTION

NOMINAL INCHES

ARP PART #

O-RINGS

X SEC

+/-

152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178

3.1/4 3.1/2 3.3/4 4 4.1/4 4.1/2 4.3/4 5 5.1/4 5.1/2 5.3/4 6 6.1/4 6.1/2 6.3/4 7 7.1/4 7.1/2 7.3/4 8 8.1/4 8.1/2 8.3/4 9 9.1/4 9.1/2 9.3/4

3.7/16 3.11/16 3.15/16 4.3/16 4.7/16 4.11/16 4.15/16 5.3/16 5.7/16 5.11/16 5.15/16 6.3/16 6.7/16 6.11/16 6.15/16 7.3/16 7.7/16 7.11/16 7.15/16 8.3/16 8.7/16 8.11/16 8.15/16 9.3/16 9.7/16 9.11/16 9.15/16

3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32 3/32

82.22 88.57 94.92 101.27 107.62 113.97 120.32 126.67 133.00 139.37 145.72 152.07 158.42 164.77 171.12 177.47 183.82 190.17 196.52 202.87 209.22 215.57 221.92 228.27 234.62 240.97 247.32

2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62

.08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08 .08

201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222

3/16 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2

7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1.00 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 1.9/16 1.5/8 1.11/16 1.3/4

1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8

4.34 5.94 7.52 9.12 10.69 12.29 13.87 15.47 17.04 18.64 20.22 21.82 23.40 24.99 26.58 28.17 29.75 31.35 32.92 34.52 36.09 37.70

3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53

.10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10

IMPERIAL O-RINGS N70 : N90 : VITON : EPDM : QUAD : NEOPRENE : SILICONE

X SEC

+/-

1.5/8 1.3/4 1.7/8 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/8 3.1/4 3.3/8 3.1/2 3.5/8 3.3/4 3.7/8 4 4.1/8 4.1/4 4.3/8 4.1/2 4.5/8 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 6.1/4 6.1/2 6.3/4 7 7.1/4 7.1/2 7.3/4 8 8.1/4 8.1/2 8.3/4 9 9.1/4 9.1/2

1.7/8 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/8 3.1/4 3.3/8 3.1/2 3.5/8 3.3/4 3.7/8 4 4.1/8 4.1/4 4.3/8 4.1/2 4.5/8 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 6.1/8 6.1/4 6.1/2 6.3/4 7 7.1/4 7.1/2 7.3/4 8 8.1/4 8.1/2 8.3/4 9 9.1/4 9.1/2 9.3/4

1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8

40.87 44.04 47.22 50.39 53.57 56.74 59.92 63.09 66.27 69.44 72.62 75.79 78.97 82.14 85.32 88.49 91.67 94.84 98.02 101.19 104.37 107.54 110.72 113.89 117.07 120.24 123.42 126.59 129.77 132.94 136.12 139.29 142.47 145.64 148.82 151.99 158.34 164.69 171.04 177.39 183.74 190.09 196.44 202.79 209.14 215.49 221.84 228.19 234.54 240.89

3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53

.10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10

O-RINGS

223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272

ACTUAL MILIMETERS

NOMINAL INCHES

ARP PART #

IMPERIAL O-RINGS N70 : N90 : VITON : EPDM : QUAD : NEOPRENE : SILICONE ACTUAL MILIMETERS

NOMINAL INCHES

ARP PART #

O-RINGS

X SEC

+/-

273 274 275 276 277 278 279 280 281 282 283 284

9.3/4 10 10.1/2 11 11.1/2 12 13 14 15 16 17 18

10 10.1/4 10.3/4 11.1/4 11.3/4 12.1/4 13.1/4 14.1/4 15.1/4 16.1/4 17.1/4 18.1/4

1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8

247.24 253.59 266.29 278.99 291.69 304.39 329.79 355.19 380.59 405.26 430.66 456.06

3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53

.10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10 .10

309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345

7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.1/2 1.5/8 1.3/4 1.7/8 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/8 3.1/4 3.3/8 3.1/2 3.5/8 3.3/4 3.7/8 4

13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 1.9/16 1.5/8 1.11/16 1.3/4 1.7/8 2 2.1/8 2.1/4 2.3/8 2.1/2 2.58 2.3/4 2.7/8 3 3.1/8 3.1/4 3.3/8 3.1/2 3.5/8 3.3/4 3.7/8 4 4.1/8 4.1/4 4.3/8

3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16

10.46 12.07 13.64 15.24 16.81 18.42 19.99 21.59 23.16 24.77 26.34 27.94 29.51 31.12 32.69 34.29 37.47 40.64 43.82 47.00 50.17 53.34 56.52 59.69 62.87 66.04 69.22 72.39 75.57 78.74 81.92 85.09 88.27 91.44 94.62 97.79 100.97

5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34

.13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13

IMPERIAL O-RINGS N70 : N90 : VITON : EPDM : QUAD : NEOPRENE : SILICONE

X SEC

+/-

4.1/8 4.1/4 4.4/8 4.1/2 4.5/8 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 6.1/4 6.1/2 6.3/4 7 7.1/4 7.1/2 7.3/4 8 8.1/4 8.1/2 8.3/4 9 9.1/4 9.1/2 9.3/4 10 10.1/2 11 11.1/2 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

4.1/2 4.1/4 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 6.1/8 6.1/4 6.3/8 6.5/8 6.7/8 7.1/8 7.3/8 7.5/8 7.7/8 8.1/8 8.3/8 8.5/8 8.7/8 9.1/8 9.3/8 9.5/8 9.7/8 10.1/8 10.3/8 10.7/8 11.3/8 11.7/8 12.3/8 13.3/8 14.3/8 15.3/8 16.3/8 17.3/8 18.3/8 19.3/8 20.3/8 21.3/8 22.3/8 23.3/8 24.3/8 25.3/8 26.3/8

3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16

104.14 107.32 110.49 113.67 116.84 120.02 123.19 126.37 129.54 132.72 135.89 139.07 142.24 145.42 148.59 151.77 158.12 164.47 170.82 177.17 183.52 189.87 196.22 202.57 208.92 215.27 221.62 227.97 234.32 240.67 247.02 253.37 266.07 278.77 291.47 304.17 329.57 354.97 380.37 405.26 430.66 456.06 481.46 506.81 532.20 557.60 582.68 608.08 633.48 658.88

5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 3.53 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34

.13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13 .13

O-RINGS

346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395

ACTUAL MILIMETERS

NOMINAL INCHES

ARP PART #

IMPERIAL O-RINGS N70 : N90 : VITON : EPDM : QUAD : NEOPRENE : SILICONE

O-RINGS

425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 445A 446 446A 447 447A 448 448A 449 449A 450 450A 451 451A 452 452A 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475

ACTUAL MILIMETERS

NOMINAL INCHES

ARP PART # ID

X SEC

+/-

4.1/2 4.5/8 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 6.1/4 6.1/2 6.3/4 7 7.1/4 7.1/2 7.3/4 8 8.1/4 8.1/2 8.3/4 9 9.1/4 9.1/2 9.3/4 10 10.1/4 10.1/2 10.3/4 11 11.1/4 11.1/2 11.3/4 12 12.1/2 13 13.1/2 14 14.1/2 15 15.1/2 16 16.1/2 17 17.1/2 18 18.1/2 19 19.1/2 20 21 22 23 24 25 26

5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 6.1/8 6.1/4 6.3/8 6.1/2 6.3/4 7 7.1/4 7.1/2 7.3/4 8 8.1/4 8.1/2 8.3/4 9 9.1/4 9.1/2 9.3/4 10 10.1/4 10.1/2 10.3/4 11 11.1/4 11.1/2 11.3/4 12 12.1/4 12.1/2 13 13.1/2 14 14.1/2 15 15.1/2 16 16.1/2 17 17.1/2 18 18.1/2 19 19.1/2 20 20.1/2 21.1/2 22.1/2 23.1/2 24.1/2 25.1/2 26.1/2

1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4

113.67 116.84 120.02 123.19 126.37 129.54 132.72 135.89 139.07 142.24 145.42 148.59 151.77 158.12 164.47 170.82 177.17 183.52 189.87 196.22 202.57 208.92 215.27 221.62 227.97 234.32 240.67 247.00 253.57 259.70 266.07 272.40 278.77 285.10 291.47 297.80 304.17 316.87 329.57 342.27 354.97 367.67 380.37 393.07 405.26 417.96 430.66 443.36 456.06 468.76 481.46 494.16 506.81 532.26 557.66 582.68 608.08 633.48 658.88

6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99

.15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

0.74 1 1.07 1.24 1.42 1.5 1.5 1.78 1.78 2 2 2 2.06 2.4 2.5 2.5 2.54 2.57 2.6 2.8 2.84 2.9 3 3 3 3 3 3.1 3.17 3.3 3.4 3.5 3.5 3.6 3.63 3.68 3.7 3.8 3.8 4 4 4 4 4 4 4.1 4.2 4.3 4.34 4.42 4.47 4.5 4.5 4.6 4.7

1.02 1 1.27 2.62 1.52 1 1.5 1.02 1.78 1 1.5 2 2.62 1.9 1.2 1.5 1.02 1.78 1.9 1.9 2.62 1.78 1 1.5 2 2.4 3 1.6 1.78 2.4 1.9 1 1.5 2.4 2.62 1.78 1.9 1.25 1.9 1 1.5 2 2.5 3 5 1.6 1.9 2.4 3.53 2.62 1.78 1.5 2 2.4 1.42

IMPERIAL-001 (1/32" * 1/32")

Q U N N B UP B UP A 70 90 C/F PTFE D

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-002 (3/64" * 3/64") IMPERIAL-102 (1/16" * 3/32) IMPERIAL-003 (1/16" * 1/16")

IMPERIAL-606 IMPERIAL-004 (5/64" * 1/16")

IMPERIAL-103 (3/32" * 3/32) RO FRENCH

IMPERIAL-607 IMPERIAL-005 (3/32" * 1/16") R1 FRENCH P3 JAPANESE IMPERIAL-104 (1/8" * 3/32") IMPERIAL-006 (1/8" * 1/16")

O-RINGS

SWEDISH UK METRIC IMPERIAL-801 SWEDISH R2 FRENCH

UK METRIC IMPERIAL-105 (5/32" * 3/32") IMPERIAL-007 (5/32" * 1/16") R2A FRENCH P4 JAPANESE

SWEDISH UK METRIC R3 FRENCH SWEDISH IMPERIAL-201 (3/16" * 1/8") IMPERIAL-106 (3/16" * 3/32") IMPERIAL-008 (3/16" * 1/16")

UK METRIC IMPERIAL-901 (3/32" TUBE OD)

S SILICONE N70 NITRILE 70-HARDNESS B UP BACKUP V75 VITON 75-HARDNESS EPDM EP AU POLYURETHANE FS FLUOROSILICONE N90 NITRILE 90-HARDNESS QUAD QUAD RING V90 VITON 90-HARDNESS CR NEOPREN HNBR HYDROGENATED NBR

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

4.74 4.8 4.9 5 5 5 5 5 5 5.1 5.23 5.28 5.3 5.4 5.5 5.5 5.6 5.7 5.8 5.94 6 6 6 6 6 6 6 6.02 6.07 6.07 6.07 6.1 6.3 6.35 6.4 6.5 6.6 6.7 6.75 6.8 7 7 7 7 7 7 7.1 7.2 7.3 7.4 7.5 7.52 7.59 7.6 7.65

1.78 1.9 1.9 1 1.2 1.5 2 2.5 3 1.6 2.62 1.78 2.4 2.3 1.2 1.5 2.4 1.9 1.9 3.53 1 1.5 2 2.5 3 3.5 6 2.62 1.3 1.63 1.78 1.6 2.4 1.78 1.9 1.5 2.4 1.3 1.78 1.9 1 1.5 1.62 2 2.5 3 1.6 1.9 2.4 2.3 1.5 3.53 2.62 2.4 1.63

IMPERIAL-802 P5 JAPANESE R4 FRENCH

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH UK METRIC IMPERIAL-107 (7/32" * 3/32") IMPERIAL-009 (7/32" * 1/16") SWEDISH

UK METRIC R5 FRENCH P6 JAPANESE IMPERIAL-202 (1/4" * 1/8")

IMPERIAL-108 (1/4" * 3/32") IMPERIAL-902 (1/8" TUBE OD) IMPERIAL-010 (1/4" * 1/16") SWEDISH UK METRIC SWEDISH IMPERIAL-803 R5A FRENCH UK METRIC IMPERIAL-610 P7 JAPANESE

SWEDISH UK METRIC R6 FRENCH SWEDISH

IMPERIAL-203 (5/16" * 1/8") IMPERIAL-109 (5/16" * 3/32") UK METRIC IMPERIAL-903 (3/16" TUBE OD)

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

7.65 7.8 7.95 8 8 8 8 8 8 8 8 8 8 8.1 8.3 8.5 8.6 8.73 8.8 8.9 8.9 8.9 8.92 9 9 9 9 9 9 9 9.1 9.12 9.19 9.25 9.3 9.6 9.8 9.8 9.92 10 10 10 10 10 10 10 10 10 10 10.1 10.3 10.46 10.5 10.5 10.52

1.78 1.9 1.78 1 1.5 1.6 1.9 2 2.5 3 3.5 4 5 1.6 2.4 1.5 2.4 1.78 1.9 1.9 2.3 2.7 1.83 1 1.5 2 2.5 3 3.5 5 1.6 3.53 2.62 1.78 2.4 2.4 1.9 2.4 2.62 1 1.5 2 2.4 2.5 3 3.5 4 5 6 1.6 2.4 5.33 2 2.7 1.83

IMPERIAL-011 (5/16" * 1/16") P8 JAPANESE IMPERIAL-804

Q U N N B UP B UP A 70 90 C/F PTFE D

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

R6A FRENCH

SWEDISH UK METRIC SWEDISH UK METRIC IMPERIAL-611 (11/32" * 15/32" * 1/16) P9 JAPANESE R7 FRENCH R8 FRENCH IMPERIAL-904 (1/4" TUBE OD)

O-RINGS

SWEDISH UK METRIC IMPERIAL-204 (3/8" * 1/8") IMPERIAL-110 (3/8" * 3/32") IMPERIAL-012 (3/8" * 1/16") SWEDISH UK METRIC P10 JAPANESE P10A JAPANESE IMPERIAL-613 (25/64" * 3/32")

SWEDISH UK METRIC SWEDISH IMPERIAL-309 (7/16" * 3/16") R9 FRENCH IMPERIAL-905 (5/16" TUBE OD)

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

10.6 10.69 10.77 10.8 10.82 10.9 11 11 11 11 11 11 11 11 11.1 11.1 11.2 11.3 11.5 11.5 11.6 11.8 11.8 11.89 11.91 12 12 12 12 12 12 12 12.07 12.1 12.1 12.29 12.3 12.37 12.42 12.6 12.7 12.9 13 13 13 13 13 13 13 13.1 13.1 13.3 13.46 13.6 13.6

2.4 3.53 2.62 2.4 1.78 2.3 1 1.5 1.6 2 2.5 3 3.5 4 1.6 1.78 2.4 2.4 1.5 2 2.4 2.1 2.4 1.98 2.62 1 1.5 2 2.5 3 3.5 4 5.33 1.6 2.7 3.53 2.4 2.62 1.78 2.4 2.62 2.3 1 1.5 2 2.5 3 3.5 4 1.6 2.62 2.4 2.08 2.4 2.7

UK METRIC IMPERIAL-205 (7/16" * 1/8") IMPERIAL-111 (7/16" * 3/32") P11 JAPANESE IMPERIAL-013 (7/16" * 1/16")

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH UK METRIC IMPERIAL-806 P11.2 JAPANESE SWEDISH

UK METRIC P12 JAPANESE IMPERIAL-906 (3/8" TUBE OD) IMPERIAL-614 (15/32" * 3/32")

IMPERIAL-310 (1/2" * 3/16") SWEDISH UK METRIC R10 FRENCH IMPERIAL-206 (1/2" * 1/8") P12.5 JAPANESE SWEDISH IMPERIAL-112 (1/2" * 3/32") IMPERIAL-014 (1/2" * 1/16") UK METRIC IMPERIAL-807

SWEDISH UK METRIC IMPERIAL-615 (33/64" * 3/32) SWEDISH IMPERIAL-907 (7/16" TUBE OD) UK METRIC R11 FRENCH

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

13.64 13.8 13.87 13.94 14 14 14 14 14 14 14 14 14 14.1 14.3 14.6 14.8 14.9 15 15 15 15 15 15 15 15 15 15 15.08 15.1 15.1 15.24 15.3 15.47 15.5 15.54 15.6 15.6 15.8 15.88 16 16 16 16 16 16 16 16 16.1 16.3 16.36 16.6 16.7 16.8 16.81

5.33 2.4 3.53 2.62 1 1.5 1.78 2 2.4 2.5 3 3.5 4 1.6 2.4 2.4 2.4 2.3 1 1.5 2 2.5 2.6 3 3.5 4 5 7 2.62 1.6 2.7 5.33 2.4 3.53 3 2.62 1.78 2.4 2.4 2.62 1 1.5 2 2.5 3 3.5 4 5 1.6 2.4 2.2 2.4 3.4 2.4 5.33

IMPERIAL-311 (9/16" * 3/16") P 14 JAPANESE IMPERIAL-207 (9/16" * 1/8") IMPERIAL-133 (9/16" * 3/32")

Q U N N B UP B UP A 70 90 C/F PTFE D

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-015 (9/16" * 1/16")

SWEDISH UK METRIC SWEDISH UK METRIC P 15 JAPANESE

O-RINGS

IMPERIAL-616 (19/32" * 3/32) SWEDISH UK METRIC R12 FRENCH IMPERIAL-312 (5/8" * 3/16") SWEDISH IMPERIAL-208 (5/8" * 1/8") IMPERIAL-114 (5/8" * 3/32") IMPERIAL-016 (5/8" * 1/16") UK METRIC P 16 JAPANESE IMPERIAL-809

SWEDISH UK METRIC SWEDISH IMPERIAL-908 (1/2" TUBE 0D) UK METRIC P 17 JAPANESE IMPERIAL-313 (11/16" * 3/16")

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

16.9 17 17 17 17 17 17 17 17.04 17.1 17.12 17.17 17.2 17.3 17.45 17.5 17.6 17.8 17.86 17.93 18 18 18 18 18 18 18 18.1 18.3 18.3 18.4 18.42 18.6 18.64 18.72 18.77 19 19 19 19 19 19 19 19 19.1 19.18 19.2 19.3 19.5 19.6 19.8 19.8 19.19 20 20

2.7 1 1.5 2 2.5 3 3.5 4 3.53 1.6 2.62 1.78 3 2.4 2.62 2.5 2.4 2.4 2.62 2.46 1 1.5 2 2.5 3 3.5 4 1.6 2.4 3.6 2.7 5.33 2.4 3.53 2.62 1.78 1 1.5 2 2.4 2.5 3 3.5 4 1.6 2.46 3 2.4 3 2.4 2.4 3.6 5.33 1 1.5

R13 FRENCH

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-209 (11/16" * 1/8) SWEDISH UK METRIC IMPERIAL-115 (11/16" * 3/32) IMPERIAL-017 (11/16" * 1/16") SWEDISH IMPERIAL-810 UK METRIC P 18 JAPANESE IMPERIAL-617 IMPERIAL-909 (9/16" TUBE OD)

SWEDISH UK METRIC R15 FRENCH R14 FRENCH IMPERIAL-314 (3/4" * 3/16") UK METRIC IMPERIAL-210 (3/4" * 1/8") IMPERIAL-116 (3/4" * 3/32") IMPERIAL-018 (3/4" * 1/16")

SWEDISH UK METRIC IMPERIAL-910 (5/8" TUBE OD) SWEDISH UK METRIC UK METRIC P 20 JAPANESE R 16 FRENCH IMPERIAL-315 (13/16" * 3/16")

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

20 20 20 20 20 20 20 20 20 20 20.2 20.22 20.29 20.3 20.35 20.64 20.7 20.8 21 21 21 21 21 21 21.3 21.3 21.5 21.59 21.6 21.7 21.8 21.82 21.89 21.92 21.95 22 22 22 22 22 22 22 22.1 22.1 22.2 22.22 22.3 22.5 22.7 23 23 23 23 23 23

2 2.5 3 3.5 4 4.5 5 6 7 8 3 3.53 2.62 2.4 1.78 2.62 3.4 2.4 1.5 2 2.5 3 3.5 5 2.4 3.6 3 5.33 2.4 3.5 2.4 3.53 2.62 2.92 1.78 1 1.5 2 2.5 3 3.5 4 1.6 3.5 3 2.62 2.4 3 3.5 1.5 2 2.5 3 3.5 3.6

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-211 (13/16" * 1/8") IMPERIAL-117 (13/16" * 3/32") IMPERIAL-019 (13/16" * 1/16") IMPERIAL-812 P 21 JAPANESE

R17 FRENCH UK METRIC IMPERIAL-316 (7/8" * 3/16") UK METRIC P 22A JAPANESE P 22 JAPANESE IMPERIAL-212 (7/8" * 1/8") IMPERIAL-118 (7/8" * 1/8") IMPERIAL-911 (11/16" TUBE OD) IMPERIAL-020 (7/8" * 1/16") I

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH UK METRIC P 22.4 JAPANESE SWEDISH IMPERIAL-813

P 23 JAPANESE

R18 FRENCH

O-RINGS

SECTION

23 23.16 23.3 23.4 23.47 23.47 23.52 23.7 23.81 24 24 24 24 24 24 24 24.1 24.2 24.3 24.4 24.5 24.6 24.6 24.7 24.77 24.99 25 25 25 25 25 25 25 25 25 25 25.04 25.07 25.1 25.12 25.2 25.2 25.3 25.5 25.7 25.8 26 26 26 26 26 26 26 26 26

4 5.33 2.4 3.53 2.62 2.95 1.78 3.5 2.62 1 1.5 2 2.5 3 3.5 4 1.6 3 2.4 3.1 3 2.4 3.6 3.5 5.33 3.53 1 1.5 2 2.5 3 3.5 4 4.5 5 7 2.95 2.62 1.6 1.78 3 3.5 2.4 3 3.5 3.53 1 1.2 1.5 2 2.5 3 3.5 4 4.5

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-317 (15/16" * 3/16") IMPERIAL-213 (15/16" * 1/8") IMPERIAL-119 (15/16" * 3/32") IMPERIAL-912 (3/4" TUBE OD) IMPERIAL-021 (15/16" * 1/6") P 24 JAPANESE IMPERIAL-814

SWEDISH G 25 JAPANESE UK METRIC UK METRIC R19 FRENCH P 25 JAPANESE IMPERIAL-318 (1" * 3/16") IMPERIAL-214 (1" * 1/8")

IMPERIAL-913 (13/16" TUBE OD) IMPERIAL-120 (1" * 3/32") SWEDISH UK METRIC IMPERIAL-022 (1" * 1/16") SWEDISH P 25.2 JAPANESE SWEDISH UK METRIC P 26 JAPANESE IMPERIAL-618

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

26 26 26.2 26.2 26.34 26.5 26.58 26.62 26.64 26.7 26.7 27 27 27 27 27 27 27 27 27.1 27.3 27.4 27.5 27.5 27.6 27.7 27.8 27.94 28 28 28 28 28 28 28 28 28 28 28.17 28.2 28.24 28.3 28.7 29 29 29 29 29 29 29 29 29.1 29.2 29.2 29.3

5 7 3 3.6 5.33 3 3.53 2.95 2.62 1.78 3.4 1.5 2 2.5 3 3.5 4 4.5 7 1.6 2.4 3.1 2.5 3 2.4 3.5 3.6 5.33 1 1.5 2 2.5 2.62 3 3.5 4 4.5 5 3.53 3 2.62 1.78 3.5 1.5 2 2.5 3 3.5 4 4.5 5 1.6 3 3.5 3.6

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

SWEDISH R20 FRENCH IMPERIAL-319 (11/16" * 3/16") UK METRIC IMPERIAL-215 (11/16" * 1/8") IMPERIAL-914 (7/8" TUBE OD) IMPERIAL-121 (11/16" * 3/32") IMPERIAL-023 (11/16" * 1/16")

SWEDISH UK MERIC SWEDISH G 28 JAPANESE UK METRIC UK METRIC P 28 JAPANESE R21 FRENCH IMPERIAL-320 (1 1/8" * 3/16")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-216 (1 1/8" * 1/8") IMPERIAL-122 (1 1/8" * 3/32") IMPERIAL-024 (1 1/8" * 1/16") P 29 JAPANESE

SWEDISH UK METRIC SWEDISH P 29.5 JAPANESE R22 FRENCH

O-RINGS

SECTION

29.3 29.3 29.4 29.5 29.51 29.6 29.7 29.7 29.74 29.75 29.82 29.87 30 30 30 30 30 30 30 30 30 30 30 30.2 30.3 30.7 30.8 31 31 31 31 31 31 31 31 31 31.12 31.12 3.2 31.35 31.4 31.42 31.47 31.5 31.6 31.7 32 32 32 32 32 32 32 32 32

5 5.7 3.1 3 5.33 2.4 3.4 3.5 2.95 3.53 2.62 1.78 1 1.5 2 2.5 3 3.5 4 4.5 5 6 7 3 2.4 3.5 3.6 1 1.5 2 2.5 3 3.5 4 4.5 5 5.33 6.99 3.5 3.53 3.1 2.62 1.78 3 2.4 3.5 1 1.5 2 2.5 3 3.5 4 4.5 5

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

G 30 JAPANESE UK METRIC IMPERIAL-321 (1 3/16" * 3/16") UK METRIC P 30 JAPANESE IMPERIAL-916 (1" TUBE OD) IMPERIAL-217 (1 3/16" * 1/8") IMPERIAL-123 (1 3/16" * 3/32") IMPERIAL-025 (1 3/16" * 1/16")

P 31 JAPANESE R23 FRENCH

IMPERIAL-322 (1 1/4" * 3/16") IMPERIAL-400 (1 1/4" * 1.4") P 31.5 JAPANESE IMPERIAL-218 (1 1/4" * 1/8") G 32 JAPANESE IMPERIAL-124 (1 1/4" * 3/32") IMPERIAL-026 (1 1/4" * 1/16") UK METRIC UK METRIC P 32 JAPANESE

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

32.1 32.2 32.5 32.5 32.69 32.7 32.92 32.99 33 33 33 33 33 33 33 33 33 33.05 33.3 33.7 34 34 34 34 34 34 34 34 34 34 34.1 34.2 34.29 34.4 34.42 34.5 34.52 34.59 34.6 34.65 34.7 35 35 35 35 35 35 35 35 35 35.1 35.2 35.5 35.6 35.7

1.6 3 3 3.6 5.33 3.4 3.53 2.62 1 1.5 2 2.5 3 3.5 4 4.5 5 1.78 2.4 3.5 1 1.5 2 2.5 3 3.5 4 4.5 5 6 3.6 3 5.33 3.1 2.95 3 3.53 2.62 2.4 1.78 3.5 1 1.5 2 2.5 3 3.5 4 4.5 5 1.6 3.5 3 3.6 3.5

SWEDISH UK METRIC SWEDISH UK METRIC R24 FRENCH IMPERIAL-323 (1 5/16" * 3/16")

Q U N N B UP B UP A 70 90 C/F PTFE D

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-219 (1 5/16" * 1/8) IMPERIAL-125 (1 5/16" * 3/32")

IMPERIAL-027 (1 5/16" * 1/16") P 34 JAPANESE

O-RINGS

R 25 FRENCH SWEDISH IMPERIAL-324 (1 3/8" * 3/16") G 35 JAPANESE IMPERIAL-918 (1 1/8" TUBE OD) UK METRIC IMPERIAL-220 (1 3/8" * 1/8") IMPERIAL-126 (1 3/8" * 3/32") UK METRIC IMPERIAL-028 (1 3/8" * 1/16") P 35 JAPANESE

SWEDISH UK METRIC P 35.5 JAPANESE UK METRIC R26 FRENCH P 36 JAPANESE

O-RINGS

SECTION

36 36 36 36 36 36 36 36 36 36.09 36.17 36.2 36.27 36.5 37 37 37 37 37 37 37 37.1 37.3 37.4 37.47 37.47 37.47 37.5 37.6 37.7 37.7 37.7 37.77 37.82 38 38 38 38 38 38 38 38 38 38 38.7 39 39 39 39 39 39 39 39.2 39.2 39.3

1.5 2 2.5 3 3.5 4 4.5 5 7 3.53 2.62 3 1.78 1.78 1.5 2 2.5 3 3.5 4 5 1.6 3.6 3.1 3 5.33 6.99 3 2.4 3 3.5 3.53 2.62 1.78 1 1.5 2 2.5 3 3.5 4 4.5 5 7 3.5 1.5 2 2.5 3 3.5 4 4.5 3 6.5 5.7

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-221 (1 7/16" * 1/8") IMPERIAL-127 (1 7/16" * 3/32") SWEDISH IMPERIAL-517 (1 7/16" * 1/16") UK METRIC

SWEDISH UK METRIC R27 FRENCH G 38 JAPANESE IMPERIAL920 (1 1/4" TUBED OD) IMPERIAL-325 (1 1/2" * 3/16") R28 FRENCH IMPERIAL-401 (1 1/2" * 1/4") UK METRIC UK METRIC P 38 JAPANESE IMPERIAL-222 (1 1/2" * 1/8") IMPERIAL-128 (1 1/2" * 3/32") IMPERIAL-029 (1 1/2" * 1/16")

P 39 JAPANESE

SWEDISH

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

39.34 39.4 39.45 39.5 39.6 39.69 39.7 40 40 40 40 40 40 40 40 40 40 40 40 40 40.64 40.65 40.7 40.87 40.94 41 41 41 41 41 41 41 41 41.28 41.5 41.6 41.7 42 42 42 42 42 42 42 42 42 42 42.2 42.5 42.52 42.86 43 43 43 43

2.62 3.1 1.78 3 2.4 3.53 3.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.7 6 6.5 7 5.33 6.99 3.5 3.53 2.62 1.5 1.78 2 2.5 3 3.5 4 4.5 3.53 3 2.4 3.5 1.5 2 2.5 3 3.5 4 4.5 5 6 7 3 3 2.62 3.53 1.5 2 2.5 3

IMPERIAL-129 (1 9/16" * 3/32") G 40 JAPANESE IMPERIAL-519 (19/16" * 1/16") UK METRIC UK METRIC IMPERIAL-824 (1 9/16" * 1/8") P 40 JAPANESE

Q U N N B UP B UP A 70 90 C/F PTFE D

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-326 (1 5/8" * 3/16") R29 FRENCH IMPERIAL-402 (1 5/8" * 1/4") P 41 JAPANESE IMPERIAL-223 (1 5/8" * 1/8") IMPERIAL-130 (1 5/8" * 3/32")

O-RINGS

IMPERIAL-030 (1 5/8" * 1/16")

IMPERIAL-825 UK METRIC UK METRIC P 42 JAPANESE

SWEDISH UK METRIC IMPERIAL-131 (1 11/16" * 3/32") IMPERIAL-826 (1 11/16" * 1/8")

O-RINGS

SECTION

43 43 43 43 43.69 43.7 43.82 43.82 44 44 44 44 44 44 44 44 44 44 44.04 44.12 44.17 44.2 44.2 44.3 44.4 44.45 44.5 44.6 44.7 45 45 45 45 45 45 45 45 45 45 45.3 45.69 45.7 46 46 46 46 46 46 46 46 46.04 46.2 46.7 46.99 47

3.5 4 4.5 5 3 3.5 5.33 6.99 1.5 2 2.5 3 3.5 4 4.5 5 6 7 3.53 2.62 1.78 3 5.7 5.7 3.1 3.53 3 2.4 3.5 1.5 2 2.5 3 3.5 4 4.5 5 6 7 5.7 2.62 3.5 1.5 2 2.5 3 3.5 4 4.5 5 3.53 3 3 6.99 1.5

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-924 (1 1/2" TUBED OD) P 44 JAPANESE IMPERIAL-327 (1 3/4" * 3/16") R30 FRENCH IMPERIAL-403 (1 3/4" * 1/4")

IMPERIAL-224 (1 3/4" * 1/8") IMPERIAL-132 (1 3/4" * 3/32") IMPERIAL-031 (1 3/4" * 1/16") SWEDISH SWEDISH UK METRIC G 45 JAPANESE IMPERIAL-827 UK METRIC UK METRIC P 45 JAPANESE

UK METRIC IMPERIAL-133 (1 13/16" * 3/32") P 46 JAPANESE

IMPERIAL-828 (1 13/16" * 1/8")

IMPERIAL-404 (1 7/8" * 1/4")

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

47 47 47 47 47 47 47 47 47 7.22 47.29 47.37 47.6 47.6 47.62 47.7 47.7 48 48 48 48 48 48 48 48 48 48 48.7 48.9 49 49 49 49 49 49 49 49 49 49.2 49.2 49.3 49.4 49.5 49.6 49.6 49.7 50 50 50 50 50 50 50 50 50

2 2.5 3 3.5 4 4.5 5 5.33 7 3.53 2.62 1.78 2.4 5.7 3.53 2.4 3.5 1.5 2 2.5 3 3.5 4 4.5 5 6 7 3.5 2.62 1 1.5 2 2.5 3 3.5 4 4.5 5 3.53 5.7 5.7 3.1 3 2.4 5.7 3.5 1 1.5 2 2.5 3 3.5 4 4.5 5

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-328 (1 7/8" * 3/16") R31 FRENCH IMPERIAL-225 (1 7/8" * 1/8") IMPERIAL-134 (1 7/8" * 3/32") IMPERIAL-032 (1 7/8" * 1/16") P 48 JAPANESE IMPERIAL-829 UK METRIC P 48 JAPANESE

P 49 JAPANESE IMPERIAL-135 (1 1516" * 3/32")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-830 (1 15/15" * 1/8") SWEDISH UK METRIC G 50 JAPANESE SWEDISH UK METRIC UK METRIC P 50A JAPANESE P 50 JAPANESE

O-RINGS

SECTION

50 50 50.17 50.17 50.39 50.47 50.52 50.8 51 51 51 51 51 51 51 51.6 51.6 52 52 52 52 52 52 52 52.07 52.3 52.39 52.4 52.6 53 53 53 53 53 53 53 53 53 53 53 53 53.09 53.34 53.34 53.57 53.64 53.67 53.98 54 54 54 54 54 54 54

6 7 5.33 6.99 3.53 2.62 1.78 3.53 1.5 2 2.5 3 3.5 4 5 2.4 5.7 1.5 2 2.5 3 3.5 4 5 2.62 5.7 3.53 3.53 5.7 1.5 2 2.5 3 3.5 4 4.5 5 5.7 6.5 7 10 3 5.33 6.99 3.53 2.62 1.78 3.53 1.5 2 2.5 3 3.5 4 4.5

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-329 (2" * 3/16") R32 FRENCH IMPERIAL-405 (2" * 1/4") IMPERIAL-226 (2" * 1/8") IMPERIAL-136 (2" * 3/32") IMPERIAL-033 (2" * 1/16") IMPERIAL-831

UK METRIC P 52 JAPANESE

IMPERIAL-137 (2 1/16" * 3/32") UK METRIC IMPERIAL-832 (2 1/16" * 1/8") P 53 JAPANESE

IMPERIAL-928 (1 3/4" TUBE OD) IMPERIAL-330 (2 1/8" * 3/16") R33 FRENCH IMPERIAL-406 (2 1/8" * 1/4") IMPERIAL-227 (2 1/8" * 1/8") IMPERIAL-138 (2 1/8: * 3/32") IMPERIAL-034 (2 1/8" * 1/16") IMPERIAL-833

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

54 54 54.2 54.3 54.4 54.5 54.6 54.6 55 55 55 55 55 55 55 55 55 55.25 55.3 55.56 55.6 56 56 56 56 56 56 56 56 56 56.52 56.52 56.74 56.82 56.87 57 57 57 57 57 57 57 57 57.15 57.4 57.6 57.6 58 58 58 58 58 58 58 58.42

5 7 5.7 5.7 3.1 3 2.4 5.7 1.5 2 2.5 3 3.5 4 4.5 5 6 2.62 5.7 3.53 5.7 1.5 2 2.5 3 3.5 4 5 6 7 5.33 6.99 3.53 2.62 1.78 1.5 2 2.5 3 3.5 4 5 7 3.53 3.1 2.4 5.7 1.5 2 2.5 3 3.5 4 5 2.62

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

SWEDISH UK METRIC G 55 JAPANESE SWEDISH UK METRIC UK METRIC P 55 JAPANESE

IMPERIAL-139 (2 3/16" * 3/32") UK METRIC IMPERIAL-834 (2 3/16" * 1/8") P 56 JAPANESE

IMPERIAL-331 (2 1/4" * 3/16") R34 FRENCH IMPERIAL-407 (2 1/4" * 1/4") IMPERIAL-228 (2 1/4" * 1/8") IMPERIAL-140 (2 1/4" * 3/32") IMPERIAL-035 (2 1/4" * 1/16")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-835 G 58 JAPANESE UK METRIC P 58 JAPANESE

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

58.74 59 59 59 59 59 59 59 59.2 59.3 59.36 59.4 59.5 59.6 59.6 59.69 59.69 59.92 60 60 60 60 60 60 60 60 60 60 60 60.05 60.33 61 61 61 61 61 61 61 61 61 61.6 61.6 61.6 61.9 62 62 62 62 62 62 62.2 62.3 62.6 62.87 62.87

3.53 1.5 2 2.5 3 3.5 4 5 5.7 5.7 3 3.1 3 2.4 5.7 5.33 6.99 3.53 1.5 2 2.5 2.62 3 3.5 4 4.5 5 6 7 1.78 3.53 1.5 2 2.5 3 3.5 4 4.5 5 7 2.4 2.62 5.7 3.53 1.5 2 2.5 3 3.5 4 5.7 5.7 5.7 5.33 6.99

IMPERIAL-836 (2 5/16" * 1/8")

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH UK METRIC IMPERIAL-932 (2" TUBE OD) G 60 JAPANESE SWEDISH UK METRIC UK METRIC P 60 JAPANESE IMPERIAL-332 (2 3/8" * 3/16") R35 FRENCH IMPERIAL-508 (2 3/8" * 1/4") IMPERIAL-229 (2 3/8" * 1/8")

IMPERIAL-142 (2 3/8" * 3/32")

IMPERIAL-036 (2 3/8" * 1/16") IMPERIAL-837

UK METRIC IMPERIAL-143 (2 7/16" * 3/32") P 62 JAPANESE IMPERIAL-838 (2 7/16" * 1/8")

SWEDISH UK METRIC P 63 JAPANESE IMPERIAL-333 (2 1/2" * 3/16") R36 FRENCH IMPERIAL-409 (2 1/2" * 1/4")

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

63 63 63 63 63 63 63 63 63.09 63.17 63.22 63.5 64 64 64 64 64 64 64 64.1 64.2 64.3 64.4 64.5 64.6 64.6 64.77 65 65 65 65 65 65 65 65 65 65 65 65.09 66 66 66 66 66 66 66 66 66 66 66.04 66.05 66.27 66.34 66.4 66.6

1.5 2 2.5 3 3.5 4 5 7 3.53 2.62 1.78 3.53 1.5 2 2.5 3 3.5 4 4.5 6.5 5.7 5.7 3.1 3 2.4 5.7 2.62 1.5 2 2.5 3 3.5 4 4.5 5 5.7 6 6.5 3.53 1.5 2 2.5 3 3.5 4 4.5 5 5.5 7 5.33 6.99 3.53 2.62 1.78 5.7

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-230 (2 1/2" * 1/8") IMPERIAL-144 (2 1/2" * 3/32") IMPERIAL-037 (2 1/2" * 1/16") IMPERIAL-839

SWEDISH UK METRIC G 65 JAPANESE SWEDISH UK METRIC UK METRIC P 65 JAPANESE IMPERIAL-145 (2 9/16" * 3/32")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-840 (2 9/16" * 1/8")

IMPERIAL-334 (2 5/8" * 3/16") R37 FRENCH IMPERIAL-410 (2 5/8" * 1/4") IMPERIAL-231 (2 5/8" * 1/8") IMPERIAL-146 (2 5/8" * 3/32") IMPERIAL-038 (2 5/8" * 1/16") P 67 JAPANESE

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

66.68 67 67 67 67 67 67 67 67 67 67.6 67.95 68 68 68 68 68 68 68 68.26 69 69 69 69 69 69 69 69 69 69.2 69.22 69.22 69.3 69.4 69.44 69.5 69.52 69.57 69.6 69.6 69.85 70 70 70 70 70 70 70 70 70 70 70 70.6 71 71

3.53 1.5 2 2.5 3 3.5 4 5 5.7 7 2.4 2.62 1.5 2 2.5 3 3.5 4 5 3.53 1.5 2 2.5 3 3.5 4 4.5 5 8 5.7 5.33 6.99 5.7 3.1 3.53 3 2.62 1.78 2.4 5.7 3.53 1.5 2 2.5 3 3.5 4 4.5 5 6 7 10 5.7 2 2.5

IMPERIAL-841

Q U N N B UP B UP A 70 90 C/F PTFE D

UK METRIC IMPERIAL147 (2 11/16" * 3/32")

IMPERIAL-842 (2 11/16" * 1/8")

SWEDISH IMPERIAL-335 (2 3/4" * 3/16") R38 FRENCH IMPERIAL-411 (2 3/4" * 1/4") UK METRIC G 70 JAPANESE IMPERIAL-232 (2 3/4" * 1/8") SWEDISH UK METRIC IMPERIAL-148 (2 3/4" * 3/32") IMPERIAL-039 (2 3/4" * 1/16") UK METRIC P 70 JAPANESE IMPERIAL-843

P 71 JAPANESE

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

71 71 71 71 71 71.12 71.2 71.44 72 72 72 72 72 72 72 72 72.39 72.39 72.62 72.69 72.75 73 73 73 73 73 73 73 73 73.03 74 74 74 74 74 74 74.2 74.3 74.3 74.4 74.5 74.6 74.61 74.63 75 75 75 75 75 75 75 75 75 75.5 75.57

3 3.5 4 4.5 5 2.62 3 3.53 2 2.5 3 3.5 4 5 6.5 7 5.33 6.99 3.53 2.62 1.78 1 2 2.5 3 3.5 4 5 7 3.53 2 2.5 3 3.5 4 5 5.7 2.62 5.7 3.1 3 5.7 3.53 5.33 2 2.5 3 3.5 4 4.5 5 7 8 3 5.33

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-149 (2 13/16/" * 3/32") IMPERIAL-844

IMPERIAL-336 (2 7/8" * 3/16") R39 FRENCH IMPERIAL-412 (2 7/8" * 1/4") IMPERIAL-233 (2 7/8" * 1/8") IMPERIAL-150 (2 7/8" * 3/32") IMPERIAL-040 (2 7/8" * 1/16")

IMPERIAL-845

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH IMPERIAL-640 (2 15/16" * 3/32") UK METRIC G 75 JAPANESE SWEDISH UK METRIC P 75 JAPANESE IMPERIAL-846 (2 15/16" * 1/8") IMPERIAL-619 (2 15/16" * 3/16")

IMPERIAL-337 (3" * 3/16") R40 FRENCH

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

75.57 75.79 75.87 75.92 76 76 76 76 76 76 76 76.2 76.89 77 77 77 77 77 77 77 77.5 77.6 78 78 78 78 78 78 78 78.74 78.75 78.97 79 79 79 79 79 79 79 79 79.2 79.3 79.4 79.5 79.6 79.77 80 80 80 80 80 80 80 80 80

6.99 3.53 2.62 1.78 1.5 2 2.5 3 3.5 4 4.5 6.8 6.5 2 2.5 3 3.5 4 5 6.5 2.62 5.7 2 2.5 3 3.5 4 5 7 5.33 6.99 3.53 1.78 2 2.5 3 3.5 4 5 7 5.7 5.7 3.1 3 5.7 5.33 1.5 2 2.5 3 3.5 4 4.5 5 5.7

IMPERIAL-413 (3" * 1/4") IMPERIAL-234 (3" * 1/8") IMPERIAL-151 (3" * 3/32") IMPERIAL-041 (3" * 1/16")

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-641 (3 1/16" * 3/32") P 78 JAPANESE

IMPERIAL-338 (3 1/8" * 3/16") R41 FRENCH IMPERIAL-414 (3 1/8" * 1/4") IMPERIAL-235 (3 1/8" * 1/8") IMPERIAL-532 (3 1/8" * 1/16")

SWEDISH UK METRIC G 80 JAPANESE SWEDISH UK METRIC P 80 JAPANESE IMPERIAL-620

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

80 80.6 81 81 81 81 81 81 81.92 81.92 82 82 82 82 82 82 82.14 82.2 82.22 82.27 83 83 83 83 83 83 83 83.8 84 84 84 84 84 84.1 84.2 84.3 84.4 84.5 84.6 85 85 85 85 85 85 85 85 85 85 80 80 80 80 80 80

6 2.62 2 2.5 3 4 5 7 5.33 6.99 2 2.5 3 4 5 7 3.53 5.7 2.62 1.78 2 2.5 3 3.5 4 5 9 2.62 2 2.5 3 4 5 5.7 5.7 5.7 3.1 3 5.7 1.5 2 2.5 3 3.5 4 4.5 5 7 10 5.33 6.99 3.53 1.78 2 3

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-642 (3 3/16" * 3/32")

IMPERIAL-339 (3 1/4" * 3/16") R42 FRENCH IMPERIAL-415 (3 1/4" * 1/4")

IMPERIAL-236 (3 1/4" * 1/8") SWEDISH IMPERIAL-152 (3 1/4" * 3/32") IMPERIAL-042 (3 1/4" * 1/16")

IMPERIAL-643 (3 5/16" * 3/32")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH SWEDISH UK METRIC G 85 JAPANESE SWEDISH UK METRIC P 85 JAPANESE

IMPERIAL-340 (3 3/8" * 3/16") R43 FRENCH IMPERIAL-416 (3 3/8" * 1/4") IMPERIAL-237 (3 3/8" * 1/8") IMPERIAL-534 (3 3/8" * 1/16")

O-RINGS

SECTION

86 87 87 87 87 87.1 87.2 88 88 88 88.27 88.27 88.49 88.57 88.62 89 89 89 89 89 89.1 89.2 89.3 89.4 89.5 89.6 89.69 90 90 90 90 90 90 90 90 90 90 91 91 91 91 91.44 91.44 91.67 91.69 92 92 92 92 92 92 93 93 93 93

4 2 3 4 5 2.4 5.7 2 3 4 5.33 6.99 3.53 2.62 1.78 2 3 4 5 7 5.7 5.7 5.7 3.1 3 5.7 5.33 2 2.5 3 3.5 4 4.5 5 6 7 8 2 3 4 5 5.33 6.99 3.53 1.78 2 3 4 5 7 10 2 3 4 5

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH

IMPERIAL-341 (3 1/2" * 3/16") R44 FRENCH IMPERIAL-417 (3 1/2" * 1/4") IMPERIAL-238 (3 1/2" * 1/8") IMPERIAL-153 (3 1/2" * 3/32") IMPERIAL-043 (3 1/2" * 1/16")

SWEDISH SWEDISH UK METRIC G 90 JAPANESE SWEDISH UK METRIC P 90 JAPANESE IMPERIAL-621 (3 9/16" * 3/16")

IMPERIAL-342 (3 5/8" * 3/16") R45 FRENCH IMPERIAL-418 (3 5/8" * 1/4") IMPERIAL-239 (3 5/8" * 1/8") IMPERIAL-536 (3 5/8" * 1/16")

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

94 94 94 94 94.1 94.3 94.4 94.5 94.6 94.62 94.62 94.84 94.92 94.97 95 95 95 95 95 95 95 95 95 96 96 96 96 96 96 97 97 97 97 97 97.79 97.79 98 98 98 98 98 98 98.02 98.05 99 99 99 99 99 99.1 99.3 99.4 99.5 99.6 100

2 2.5 3 4 5.7 5.7 3.1 3 5.7 5.33 6.99 3.53 2.62 1.78 1.5 2 2.5 3 3.5 4 5 6 7 2 2.5 3 4 5 6 2 2.5 3 4 5 5.33 6.99 1.5 2 2.5 3 4 7 3.53 1.78 2 2.5 3 4 5.7 5.7 5.7 3.1 3 5.7 1

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

SWEDISH UK METRIC G 95 JAPANESE SWEDISH UK METRIC P 95 JAPANESE IMPERIAL-343 (3 3/4" * 3/16") R46 FRENCH IMPERIAL-419 (3 3/4" * 1/4") IMPERIAL-240 (3 3/4" * 1/8") IMPERIAL-154 (3 3/4" * 3/32") IMPERIAL-044 (3 3/4" * 1/16")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-344 (3 7/8" * 3/16") R47 FRENCH IMPERIAL-420 (3 7/8" * 1/4")

IMPERIAL-241 (3 7/8" * 1/8") IMPERIAL-538 (3 7/8" * 1/16")

SWEDISH UK METRIC G 100 JAPANESE SWEDISH UK METRIC P 100 JAPANESE

O-RINGS

SECTION

100 100 100 100 100 100 100 100 100 100 100.97 100.97 101 101 101.19 101.27 101.34 101.6 102 102 103 103 104 104 104.1 104.14 104.15 104.3 104.37 104.4 104.4 104.5 104.6 105 105 105 105 105 105 105 105.5 106 106.4 107 107 107.32 107.32 107.54 107.62 107.7 108 108 108 108 108

2 2.5 3 3.5 4 4.5 5 5.33 6 7 5.33 6.99 3 7 3.53 2.62 1.78 5.7 3 4 2 3 3 7 5.7 5.33 6.99 5.7 3.53 1.78 3.1 3 5.7 2 2.5 3 4 4.5 5 7 3 2 3.1 2 32 5.33 6.99 3.53 2.62 1.78 2.5 3 4 6 7

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-622(3 15/16" * 3/16")

IMPERIAL-345 (4" * 3/16") R48 FRENCH IMPERIAL-421 (4" * 1/4")

IMPERIAL-242 (4" * 1/8") IMPERIAL-155 (4" * 3/32") IMPERIAL-045 (4" * 1/16") P 102 JAPANESE

SWEDISH IMPERIAL-346 (4 1/8" * 3/16") R49 FRENCH IMPERIAL-422 (4 1/8" * 1/4") UK METRIC IMPERIAL-243 (4 1/8" * 1/8") IMPERIAL-540 (4 1/8" * 1/16") G 105 JAPANESE SWEDISH UK METRIC P 105 JAPANESE

G 107 JAPANESE

IMPERIAL-347 (4 1/4" * 3/16") R50 FRENCH IMPERIAL-423 (4 1/4" * 1/4") IMPERIAL-244 (4 1/4" * 1/8") IMPERIAL-156 (4 1/4" * 3/32") IMPERIAL-046 (4 1/4" * 1/16")

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

109 109.1 109.3 109.4 109.5 109.54 109.6 110 110 110 110 110 110 110 110 110.49 110.49 110.72 110.74 111 111.6 112 112 112 113 113 113.67 113.67 113.89 113.97 114 114 114.3 114.4 114.5 114.6 114.7 115 115 115 115 115 115 115 116 116 116.84 116.84 117 117.07 117.1 117.5 118 118 119

3 5.7 5.7 3.1 3 5.33 5.7 2 2.5 3 4 4.5 5 6 7 5.33 6.99 3.53 1.78 12 5.7 3 4 7 2.5 4 5.33 6.99 3.53 2.62 1.78 5 5.7 3.1 3 5.7 6.99 2 2.5 3 4 4.5 5 6 3 3.5 5.33 6.99 4 3.53 1.78 5.33 3 6 3

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

SWEDISH UK METRIC G 110 JAPNESE SWEDISH UK METRIC IMPERIAL-623 P 110 JAPANESE

IMPERIAL-348 (4 3/8" * 3/16") R51 FRENCH IMPERIAL-424 (4 3/8" * 1/4") IMPERIAL-245 (4 3/8" * 1/8") IMPERIAL-542 (4 3/8" * 1/16") P 112 JAPANESE

IMPERIAL-349 (4 1/2" * 3/16") R52 FRENCH IMPERIAL-425 (4 1/2" * 1/4") R53 FRENCH IMPERIAL-246 (4 1/2" * 1/8") IMPERIAL-157 (4 1/2" * 3/32") IMPERIAL-047 (4 1/2" * 1/16")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH UK METRIC G 115 JAPANESE SWEDISH UK METRIC P 115 JAPANESE IMPERIAL-624 (4 9/16" * 1/4")

IMPERIAL-350 (4 5/8" * 3/16") IMPERIAL-426 (4 5/8" * 1/4") R54 FRENCH IMPERIAL-247 (4 5/8" * 1/8") IMPERIAL-544 (4 5/8" * 1/16") IMPERIAL-860

O-RINGS

SECTION

119 119.3 119.4 119.5 119.6 120 120 120 120 120 120 120 120.2 120.2 120.24 120.32 120.4 120.7 122 122 123 123 123.19 123.19 123.42 123.44 123.8 124.3 124.4 124.5 124.6 124.6 125 125 125 125 125 125 125 126 126 126.37 126.37 126.59 126.67 126.76 127 128 129.3 129.4 129.4 129.5 129.54 129.54 129.6

12 5.7 3.1 3 5.7 2 2.5 3 4 4.5 5 6 5.33 6.99 3.53 2.62 1.78 5.33 2 3.5 2.5 3.5 5.33 6.99 3.53 1.78 5.33 5.7 3.1 3 5.7 6.99 2 2.5 3 4 5 6 8 3 4 5.33 6.99 3.53 2.62 1.78 5.33 3 5.7 1.78 3.1 3 5.33 6.99 5.7

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

SWEDISH UK METRIC G 120 JAPANESE SWEDISH UK METRIC P 120 JAPANESE

IMPERIAL-351 (4 3/4" * 3/16") IMPERIAL-427 (4 3/4" * 1/4") R55 FRENCH IMPERIAL-248 (4 3/4" * 1/8") IMPERIAL-158 (4 3/4 * 3/32") IMPERIAL-048 (4 3/4" * 1/16") IMPERIAL-861

IMPERIAL-352 (4 7/8" * 3/16") IMPERIAL-428 (4 7/8" * 1/4") R56 FRENCH IMPERIAL-249 (4 7/8" * 1/8") IMPERIAL-546 (4 7/8" * 1/16") IMPERIAL-862 SWEDISH UK METRIC G 125 JAPANESE SWEDISH UK METRIC P 125 JAPANESE IMPERIAL-625

IMPERIAL-353 (5" * 3/16") IMPERIAL-429 (5" * 1/4") R57 FRENCH IMPERIAL-250 (5" * 1/8") IMPERIAL-159 (5" * 3/32") IMPERIAL-049 (5" * 1/16") IMPERIAL-863 SWEDISH UK METRIC IMPERIAL-548 (5 1/8" * 1/16") G 130 JAPANESE SWEDISH UK METRIC IMPERIAL-354 (5 1/8" * 3/16") IMPERIAL-430 (5 1/8" * 1/4") R58 FRENCH P 130 JAPANESE

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

129.77 130 130 130 130 130 130 130.18 130.5 131 131.6 132 132.72 132.72 132.94 133 133 133 133.07 133.35 134 134 134.3 134.4 134.5 134.5 134.6 135 135 135 135 135 135 135 135.76 135.89 135.89 136.12 136.53 138.94 139 139.07 139.07 139.29 139.3 139.37 139.4 139.5 139.6 139.7 140 140 140 140 140

3.53 2 2.5 3 4 5 6.5 5.33 4 3.5 5.7 4 5.33 6.99 3.53 2.62 4 4.5 1.78 5.33 3 4 5.7 3.1 3 6.99 5.7 2 2.5 3 4 5 6 8 1.78 5.33 6.99 3.53 5.33 1.78 3 5.33 6.99 3.53 5.7 2.62 3.1 3 5.7 5.33 2 2.5 3 4 5

IMPERIAL-251 (5 1/8" * 1/8")

Q U N N B UP B UP A 70 90 C/F PTFE D

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-864

P 132 JAPANESE IMPERIAL-355 (5 1/4" * 3/16") IMPERIAL-431 (5 1/4" * 1/4") R59 FRENCH IMPERIAL-252 (5 1/4" * 1/8") IMPERIAL-160 (5 1/4 * 3/32")

IMPERIAL-050 (5 1/4" * 1/16") IMPERIAL-865

O-RINGS

SWEDISH UK METRIC G 135 JAPANESE SWEDISH UK METRIC IMPERIAL-626 P 135 JAPANESE

IMPERIAL-550 (5 3/8" * 1/16") IMPERIAL-356 (5 3/8" * 3/16") IMPERIAL-432 (5 3/8" * 1/4") R60 FRENCH IMPERIAL-253 (5 3/8" * 1/8") IMPERIAL-866 IMPERIAL-551 (5 1/2" * 1/16") IMPERIAL-357 (5 1/2" *3/16") IMPERIAL-433 (5 1/2" * 1/4") R61 FRENCH IMPERIAL-254 (5 1/2" * 1/8") SWEDISH UK METRIC IMPERIAL-161 (5 1/2" * 3/32") G 140 JAPANESE SWEDISH UK METRIC P 140 JAPANESE IMPERIAL-867

O-RINGS

SECTION

140 142 142.11 142.24 142.24 142.47 142.88 144.1 144.3 144.4 144.5 144.6 145 145 145 145 145.29 145.42 145.42 145.64 145.72 146 146.05 147.3 148.46 148.59 148.59 148.82 149 149.1 149.2 149.3 149.3 149.5 149.6 150 150 150 150 150 151.64 151.77 151.77 151.99 152 152 152.07 153 153 154.1 154.3 154.5 154.5 154.81 155

8 5 1.78 5.33 6.99 3.53 5.33 8.4 5.7 3.1 3 5.7 2.5 3 4 5 1.78 5.33 6.99 3.53 2.62 2 5.33 5.7 1.78 5.33 6.99 3.53 3 8.4 5.34 5.7 3 8.4 5.7 2 2.5 3 4 5 1.78 5.33 6.99 3.53 3 12 2.62 4 4.5 8.4 5.7 3 8.4 1.78 2.5

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-552 (5 5/8" * 1/16") IMPERIAL-358 (5 5/8" * 3/16") IMPERIAL-434 (5 5/8" * 1/4") R62 FRENCH IMPERIAL-255 (5 5/8" * 1/8") IMPERIAL-868 SWEDISH UK METRIC SWEDISH UK METRIC G 145 JAPANESE SWEDISH UK METRIC P 145 JAPANESE

IMPERIAL-553 (5 3/4" * 1/16") IMPERIAL-359 (5 3/4" * 3/16") IMPERIAL-435 (5 3/4" * 1/4") R63 FRENCH IMPERIAL-256 (5 3/4" * 1/8") IMPERIAL-162 (5 3/4" * 3/32") IMPERIAL-869 IMPERIAL-554 (5 7/8" * 1/16") IMPERIAL-360 (5 7/8" * 3/16") IMPERIAL-436 (5 7/8" * 1/4") R64 FRENCH IMPERIAL-257 (5 7/8" * 1/8") SWEDISH UK METRIC IMPERIAL-870 G 150 JAPANESE SWEDISH UK METRIC UK METRIC P 150A JAPANESE P 150 JAPANESE

IMPERIAL-555 (6" * 1/16") IMPERIAL-361 (6" * 3/16") IMPERIAL-437 (6" * 1/4") R65 FRENCH IMPERIAL-258 (6" * 1/8")

IMPERIAL-163 (6" * 3/32")

SWEDISH UK METRIC G 155 JAPANESE SWEDISH UK METRIC UK METRIC P 155 JAPANESE IMPERIAL-556 (6 1/8" * 1/16")

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

155 155 155 155.6 156 158 158 158 158.12 158.12 158.34 158.42 159.1 159.3 159.5 159.5 159.5 160 160 160 160 160 160 160 161.16 161.3 161.9 164 164 164.1 164.3 164.34 164.47 164.47 164.5 164.5 164.69 164.77 165 165 165 165 166.7 167.51 167.7 168.3 169.1 169.3 169.5 169.5 170 170 170 170 170.69

3 4 5.33 6.99 4 1.78 3 6 5.33 6.99 3.53 2.62 8.4 5.7 3 6.99 8.4 2 2.5 3 3.5 4 5 6 1.78 5.33 6.99 2 3 8.4 5.7 1.78 5.33 6.99 3 8.4 3.53 2.62 2.5 3 4 5 6.99 1.78 5.33 6.99 8.4 5.7 3 8.4 3 4 5 10 1.78

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-644 (6 1/8" * 3/16") IMPERIAL-872 (6 1/8" * 1/4") IMPERIAL-557 (6 1/4" * 1/16")

IMPERIAL-362 (6 1/4" * 3/16") IMPERIAL-438 (6 1/4" * 1/4") R66 FRENCH IMPERIAL-259 (6 1/4" * 1/8") IMPERIAL-164 (6 1/4" * 3/32") SWEDISH UK METRIC G 160 JAPANESE SWEDISH UK METRIC UK METRIC IMPERIAL-627 P 160 JAPANESE

IMPERIAL-558 (6 3/8" * 1/16") IMPERIAL-645 (6 3/8" * 3/16") IMPERIAL-874

SWEDISH UK METRIC G 165 JAPANESE SWEDISH UK METRIC IMPERIAL-559 (6 1/2" * 1/16") IMPERIAL-363 (6 1/2" * 3/16") IMPERIAL-439(6 1/2" * 1/4") R67 FRENCH UK METRIC P 165 JAPANESE IMPERIAL-260 (1 1/2" * 1/8") IMPERIAL-165 (6 1/2" * 3/32")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-628 (6 5/8" * 1/4") IMPERIAL-560 (6 5/8" * 1/16") IMPERIAL-646 (6 5/8" * 3/16") IMPERIAL-876 (6 5/8" * 1/4") SWEDISH UK METRIC G 170 JAPANESE SWEDISH UK METRIC UK METRIC P 170 JAPANESE

IMPERIAL-561 (6 3/4" * 1/16")

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

170.82 170.82 171 171.04 171.12 173.87 174 174 174 174.1 174.3 174.5 174.5 174.6 175 175 177.17 177.17 177.39 177.47 178 179.1 179.3 179.5 179.5 180 180 180 181 183.52 183.52 183.74 183.82 184 184.1 184.3 184.5 184.5 185 185 185 185 187 187.3 189.1 189.3 189.5 189.5 189.87 189.87 190 190 190 190.09 190.17

5.33 6.99 3 3.53 2.62 1.78 3 4 5.33 8.4 5.7 3 8.4 6.99 3 4 5.33 6.99 3.53 2.62 2 8.4 5.7 3 8.4 3 4 5 6.99 5.33 6.99 3.53 2.62 3 8.4 5.7 3 8.4 3 4 5 6 3.5 6.99 8.4 5.7 3 8.4 5.33 6.99 3 4 5 3.53 2.62

IMPERIAL-364 (6 3/4" * 3/16") IMPERIAL-440 (6 3/4" * 1/4") R68 FRENCH

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-261 (6 3/4" * 1/8") IMPERIAL-166 (6 3/4" * 3/32") IMPERIAL-562 (6 7/8" * 1/16")

IMPERIAL-647 (6 7/8" * 3/16") SWEDISH UK METRIC G 175 JAPANESE SWEDISH UK METRIC UK METRIC P 175 JAPANESE IMPERIAL-878 (6 7/8" * 1/4")

IMPERIAL-365 (7" * 3/16") IMPERIAL-441 (7" * 1/4") R69 FRENCH IMPERIAL-262 (7" * 1/8") IMPERIAL-167 (7" * 3/32") SWEDISH UK METRIC G 180 JAPANESE SWEDISH UK METRIC UK METRIC P 180 JAPANESE

IMPERIAL-880 (7 1/8" * 1/4") IMPERIAL-366 (7 1/4" * 3/16") IMPERIAL-442 (7 1/4" * 1/4") R70 FRENCH IMPERIAL-263 (7 1/4" * 1/8") IMPERIAL-168 (7 1/4" * 3/32") SWEDISH UK METRIC G 185 JAPANESE SWEDISH UK METRIC UK METRIC P 185 JAPANESE

IMPERIAL-882 (7 3/8" * 1/4") SWEDISH UK METRIC G 190 JAPANESE SWEDISH UK METRIC UK METRIC P 190 JAPANESE IMPERIAL-367 (7 1/2" * 3/16") IMPERIAL-443 (7 1/2" * 1/4" ) R71 FRENCH

IMPERIAL-264 (7 1/2" * 1/8") IMPERIAL-169 (7 1/2" * 3/32")

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

193.7 194.1 194.3 194.5 194.5 195 195 195 196.22 196.22 196.44 196.52 197.3 199.1 199.3 199.5 199.5 200 200 200 200 200 200 202.57 202.57 202.79 202.87 203 204 204.1 204.5 204.5 205 205 205 207 208.5 208.92 208.92 209.1 209.14 209.22 209.3 209.5 210 210 210 214.3 214.5 215 215 215.27 215.27 215.49 215.57

6.99 8.4 5.7 3 8.4 3 4 5 5.33 6.99 3.53 2.62 5.7 8.4 5.7 3 8.4 3 4 4.6 5 6 7 5.33 6.99 3.53 2.62 3 4 8.4 3 8.4 3 4 5 3 8.4 5.33 6.99 8.4 3.53 2.62 5.7 8.4 3 4 5 5.7 8.4 3 4 5.33 6.99 3.53 2.62

IMPERIAL-884 (7 5/8" * 1/4") SWEDISH UK METRIC G 195 JAPANESE SWEDISH UK METRIC UK METRIC P 195 JAPANESE

Q U N N B UP B UP A 70 90 C/F PTFE D

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-368 (7 3/4" * 3/16") IMPERIAL-444 (7 3/4" * 1/4") R72 FRENCH IMPERIAL-265 (7 3/4" * 1/8") IMPERIAL-170 (7 3/4" * 3/32) SWEDISH UK METRIC G 200 JAPANESE SWEDISH UK METRIC UK METRIC P 200 JAPANESE

IMPERIAL-886 (7 7/8" * 1/4") IMPERIAL-369 (8" * 3/16") IMPERIAL-445 (8" * 1/4") R73 FRENCH IMPERIAL-266 (8" * 1/8") IMPERIAL-171 (8" * 3/32")

O-RINGS

UK METRIC UK METRIC P 205 JAPANESE

P 209 JAPANESE IMPERIAL-370 (8 1/4" * 3/16") IMPERIAL-674 -445A (8 1/4" * 1/4") SWEDISH UK METRIC IMPERIAL-267 (8 1/4" * 1/8") IMPERIAL-172 (8 1/4" * 1/16") G 210 JAPANESE SWEDISH UK METRIC P 210 JAPANESE

G 215 JAPANESE P 215 JAPANESE

IMPERIAL-371 (8 1/2" * 3/16") IMPERIAL-446 (8 1/2" * 1/4") R74 FRENCH IMPERIAL-268 (8 1/2" * 1/8") IMPERIAL-173 (8 1/2" * 3/32")

O-RINGS

SECTION

ALL SIZES ACTUAL IN mm

219.1 219.3 219.5 219.5 220 220 220 221.62 221.62 221.84 221.92 224.5 225 225 227.97 227.97 228.19 228.27 229.1 229.3 229.5 229.5 230 230 234.1 234.32 234.32 234.5 234.54 234.62 239.1 229.3 239.5 239.5 240 240 240 240 240.67 240.67 240.89 240.97 244.5 245 245.2 247 247.02 247.24 247.32 248 249.1 249.3 249.5 249.5 250

8.4 5.7 3 8.4 3 4 5 5.33 6.99 3.53 2.62 8.4 3 4 5.33 6.99 3.53 2.62 8.4 5.7 3 8.4 3 4 8.4 5.33 6.99 8.4 2.62 2.62 8.4 5.7 3 8.4 3 4 5 7 5.33 6.99 3.53 2.62 8.4 4 5.7 6.99 5.33 3.53 2.62 5 8.4 5.7 3 8.4 3

SWEDISH UK METRIC G 220 JAPANESE SWEDISH UK METRIC UK METRIC P 220 JAPANESE

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-372 (8 3/4" * 3/16") IMPERIAL-676 -446A (8 3/4" * 1/4") IMPERIAL-269 (8 3/4 " * 1/8") IMPERIAL-174 (8 3/4" * 3/32") P 225 JAPANESE

IMPERIAL-373 (9" * 3/16") IMPERIAL-447 (9" * 1/4") R75 FRENCH IMPERIAL-270 (9" * 1/8") IMPERIAL-175 (9" * 3/32") SWEDISH UK METRIC G 230 JAPANESE SWEDISH UK METRIC UK METRIC P 230 JAPANESE

UK METRIC IMPERIAL-374 (9 1/4" * 3/16") IMPERIAL-678 -447A (9 1/4" * 1/4") P 235 JAPANESE IMPERIAL-271 (9 1/4" * 1/8") IMPERIAL-176 (9 1/" * 3/32") SWEDISH UK METRIC G 240 JAPANESE SWEDISH UK METRIC UK METRIC P 240 JAPANESE

IMPERIAL-375 (9 1/2" * 3/16") IMPERIAL-448 (9 1/2" * 1/4") R76 FRENCH IMPERIAL-272 (9 1/2" * 1/8") IMPERIAL-177 (9 1/2" * 3/32") P 245 JAPANESE G 245 JAPANESE IMPERIAL-680 -448A (9 3/4" * 1/4") IMPERIAL-376 (9 3/4" * 3/16") IMPERIAL-273 (9 3/4" * 1/8") IMPERIAL-178 (9 3/4" * 3/32") SWEDISH UK METRIC G 250 JAPANESE SWEDISH UK METRIC UK METRIC P 250 JAPANESE

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

250 253.37 253.57 253.59 254.5 255 255 259.3 259.5 259.7 264 264.5 265 266.07 266.07 266.29 269.3 269.5 270 270 272.4 274.3 274.5 275 276 278.77 278.77 278.99 279.3 279.5 280 280 284.5 285 285.1 288 289.3 289.5 290 291.47 291.47 291.69 294.5 295 295.3 297.8 299.3 299.5 300 300 300 304.17 304.17 304.39 305

4 5.33 6.99 3.53 8.4 3 4 5.7 8.4 6.99 4 8.4 3 5.33 6.99 3.53 5.7 8.4 3 5 6.99 5.7 8.4 3 8.4 5.33 6.99 3.53 5.7 8.4 3 4 8.4 3 6.99 4 5.7 8.4 4 5.33 6.99 3.53 8.4 3 5.7 6.99 5.7 8.4 3 4 6 5.33 6.99 3.53 3

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-377 (10" * 3/16") IMPERIAL-449 (10" * 1/4") R77 FRENCH IMPERIAL-274 (10" * 1/8") P 255 JAPANESE

G 260 JAPANESE SWEDISH UK METRIC P 260 JAPANESE IMPERIAL-682 -449A (10 1/4" * 1/4") P 265 JAPANESE IMPERIAL-378 (10 1/2" * 3/16") IMPERIAL-450 (10 1/2" * 1/4") R78 FRENCH IMPERIAL-275 (10 1/2" * 1/8") G 270 JAPANESE SWEDISH UK METRIC P 270 JAPANESE

IMPERIAL-684 -450A (10 3/4" * 1/4") G 275 JAPANESE P 275 JAPANESE

IMPERIAL-379 (11" * 3/16") IMPERIAL-451 (11" * 1/4") R79 FRENCH IMPERIAL-276 (11" * 1/8") G 280 JAPANESE SWEDISH UK METRIC P 280 JAPANESE

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

P 285 JAPANESE IMPERIAL-686 -451A (11 1/" * 1/4") G 290 JAPANESE SWEDISH UK METRIC P 295 JAPANESE IMPERIAL-380 (11 1/2" * 3/16") IMPERIAL-452 (11 1/2" * 1/4") R80 FRENCH IMPERIAL-277 (11 1/2" * 1/8") P 295 JAPANESE G 295 JAPANESE IMPERIAL-688 -452A (11 3/4" * 1/4") G 300 JAPANESE SWEDISH UK METRIC P 300 JAPANESE

IMPERIAL-381 (12" * 3/16") IMPERIAL-453 (12" * 1/4") R81 FRENCH IMPERIAL-278 (12" * 1/8")

O-RINGS

SECTION

310 310.5 314.3 314.5 315 316.87 319.3 319.5 320 320 323.2 327 329.3 329.57 329.57 329.79 334.5 335.9 338 339.3 339.5 340 342.27 347 350 350 350 354.5 354.97 354.97 355.19 359.3 359.5 362 363 367.67 374.5 375 375.3 378 379.3 380 380.37 380.37 380.59 384.5 385 392 393.07 399.3 399.5 405 405.26 405.26 405.26

5 6.99 5.7 8.4 5 6.99 5.7 8.4 4 5 6.99 4 5.7 5.33 6.99 3.53 8.4 6.99 6 5.7 8.4 5 6.99 7 3 4 6 8.4 5.33 6.99 3.53 5.7 8.4 4 4 6.99 8.4 5 8.4 4 5.7 5 5.33 6.99 3.53 8.4 5 5 6.99 5.7 8.4 4 3.53 5.33 6.99

ALL SIZES ACTUAL IN mm

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-648 (12 1/4" * 1/4") G 315 JAPANESE P 315 JAPANESE IMPERIAL-454 (12 1/2" * 1/4") R82 FRENCH G 320 JAPANESE SWEDISH UK METRIC P 320 JAPANESE

IMPERIAL-649 (12 3/4" * 1/4") G 330 JAPANESE IMPERIAL-382 (13" * 3/16") IMPERIAL-455 (13" * 1/4") R83 FRENCH IMPERIAL-279 (13" * 1/8") P 335 JAPANESE IMPERIAL-650 (13 1/4" * 1/4") SWEDISH UK METRIC P 340 JAPANESE IMPERIAL-456 (13 1/2" * 1/4") R84 FRENCH

P 355 JAPANESE IMPERIAL-383 (14" * 3/16") IMPERIAL-457 (14" * 1/4") IMPERIAL-280 (14" * 1/8") SWEDISH UK METRIC P 360 JAPANESE

IMPERIAL-458 (14 1/2" * 1/4") R86 FRENCH P 375 JAPANESE P 380 JAPANESE G 380 JAPANESE SWEDISH UK METRIC IMPERIAL-384 (15" * 3/16") IMPERIAL459 (15" * 1/4") R87 FRENCH IMPERIAL-281 (15" * 1/8") P 385 JAPANESE

IMPERIAL-460 (15 1/2" * 1/4") R88 FRENCH SWEDISH UK METRIC G 400 JAPANESE P 400 JAPANESE IMPERIAL-282 (16" * 1/8") IMPERIAL-385 (16" * 3/16") IMPERIAL-461 (16" * 1/4")

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

O-RINGS

SECTION

408 417.96 419.3 430.66 430.66 430.66 439.3 443.36 456.06 456.06 456.06 459.3 468.76 479.3 481.46 481.46 494.16 499.3 506.81 506.81 509.3 510 520 532.2 532.26 557.6 557.66 582.68 582.68 608.08 608.08 615 633.48 633.48 658.88 658.88 939.8 1219.2 1219.2

6 6.99 5.7 3.53 5.33 6.99 5.7 6.99 3.53 5.33 6.99 5.7 6.99 5.7 5.33 6.99 6.99 5.7 5.33 6.99 5.7 5.7 5 5.33 6.99 5.33 6.99 5.33 6.99 5.33 6.99 7 5.33 6.99 5.33 6.99 5.34 3.53 5.34

ALL SIZES ACTUAL IN mm

V V 75 90

E P D M

C R

F S

H N B R

P T F E

E N C A P.

A U

IMPERIAL-462 (16 1/2" * 1/4") SWEDISH UK METRIC G 420 JAPANESE IMPERIAL-283 (17" * 1/8") IMPERIAL-386 (17" * 3/16") IMPERIAL-463 (17" * 1/4") SWEDISH UK METRIC IMPERIAL-464 (17 1/2" * 1/4") IMPERIAL-284 (18" * 1/8") IMPERIAL-387 (18" * 3/16") IMPERIAL-465 (18" * 1/4") SWEDISH UK METRIC IMPERIAL-466 (18" 1/2" * 1/4") SWEDISH UK METRIC IMPERIAL-388 (19" * 3/16") IMPERIAL-467 (19" * 1/4") IMPERIAL-468 (19 1/2" * 1/4") SWEDISH UK METRIC IMPERIAL-389 (20" * 3/16") IMPERIAL-469 (20" * 1/4") G 510 JAPANESE

IMPERIAL-390 (21" * 3/16") IMPERIAL-470 (21" * 1/4") IMPERIAL-391 (22" * 3/16") IMPERIAL-471 (22" * 1/4") IMPERIAL-392 (23" * 3/16") IMPERIAL-472 (23" * 1/4") IMPERIAL-393 (24" * 3/16") IMPERIAL-473 (24" * 1/4")

O-RINGS

Q U N N B UP B UP A 70 90 C/F PTFE D

IMPERIAL-394 (25" * 3/16") IMPERIAL-474 (25" * 1/4") IMPERIAL-395 (26" * 3/16") IMPERIAL-475 (26" * 1/4")

O-RING CORD

1.78mm to 19mm NITRILE VITON SILICONE EPDM O-RINGS

HEAT VULANIZED ANY SIZE ORING Cycanoacrylate adhesive is available for out in the field urgent repairs

TUBE FITTING BOSS O-RINGS 900 SERIES UNF O-RINGS

901 902 903 904 905 906 907 908 909 910 911 912 913 914 916 918 920 924 928 932

3/32 1/8 3/16 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 1 1-1/8 1-1/4 1-1/2 1-3/4 2

1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4 13/16 7/8 1 1-1/16 1-1/8 1-3/16 1-5/16 1-1/2 1-5/8 1-7/8 2-1/4 2-1/2

24 24 24 20 20 18 18 16 16 14 12 12 12 12 12 12 12 12 12 12

0.185 0.239 0.301 0.351 0.414 0.468 0.530 0.644 0.706 0.755 0.863 0.924 0.986 1.048 1.171 1.355 1.475 1.720 2.090 2.337

O-RING THICK 0.056 0.064 0.064 0.072 0.072 0.078 0.082 0.087 0.097 0.097 0.116 0.116 0.116 0.116 0.116 0.116 0.118 0.118 0.118 0.118

This chart gives thread size and o-ring size as used on straight thread connectors, straight thread tube fittings, etc. These sizes are applicable for SAE. AN. and MS. connections. O-rings used for straight thread connectors do not conform to so-called "standard size". They should be purchased specifically for this service and should conform to the dimensions shown.

THIS SERIES IS ALSO AVAILABLE IN KIT FORM

O-RINGS

PART #

STRAIGHT THREAD FITTING SIZES T.P.I. O-RING I.D. TUBING O.D. THREAD SIZE

O-RING KITS NITRILE 1 IMPERIAL

N70

27 SIZES

190 PIECES

1B METRIC (JAPANESE)

N70

30 SIZES

380 PIECES

2 METRIC (EUROPEAN)

N70

32 SIZES

428 PIECES

2A METRIC 2MM X SECTION ONLY

N70

60 SIZES

410 PIECES

2B METRIC 3MM X SECTION ONLY

N70

59 SIZES

288 PIECES

3 IMPERIAL

N90

32 SIZES

382 PIECES

11 UNF / SAE

N90

16 SIZES

160 PIECES

10 TUBE FITTINGS

N90

20 SIZES

212 PIECES

ORF O-RING FACE SEALS

N90

8 SIZES

80 PIECES

O SECTION 1/16" IMPERIAL

N90

24 SIZES

244 PIECES

13A SPLICING KIT IMPERIAL 13B SPLICING KIT METRIC

BONDED WASHER KITS O-RINGS

IMPERIAL -- BSP --

10 SIZES

88 PIECES

METRIC

10 SIZES

88 PIECES

SAE - FLANGE SEALS

PART #

REPLACES 0-RING NUMBER

OUTSIDE DIAMETER -0.000 +0.015

NORMAL FLANGE SIZE

FS 08 FS 12 FS 16 FS 20 FS 24 FS 32 FS 40 FS 48 FS 56 FS 64 FS 80

210 214 219 222 225 228 232 237 241 245 253

1.005 1.255 1.565 1.755 2.125 2.500 3.005 3.625 4.115 4.615 5.615

1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 3-1/2 4 5

Flange seals are suitable for use in standard hydraulic fluids in a temperature range of 40 degrees F to + 220 degrees F and 0 to 6,000 p.s.i. Flange seals can provide direct replacement for o-rings without any modifications of the existing grooves.

ORIGINAL RANGE - BRITISH IMPERIAL BONDED SEAL THREAD DIA SIZE M REFERENCE INCH 4BA 1BA 2BA 1/4 1/4 1/16 1/16 1/8 40 1/16 1/2 1/16 60 4/8

BSP

1/8 1/4

2/8 11/16 4/8 14/16 4/8 15/16 1 1 1/16 1 1/8 1 1/16 1 1/4 1 5/10 1 5/10 1 3/8 1 1/2 1 1/2 1 1/4 1 1/8 2 2 1/8 2 1/4

1/2 5/8 3/4 7/8 1 1 1 1/4 1 1/2 1 1/8 2

2 1/2 2 1/4 2 1/2

*** 001 002 003 004 005 006 007 020 008 009 021 010 022 011 023 012 024 025 026 013 027 028 014 029 015 030 031 0.16 017 032 0.18 033 019 034 035 036 037 038 039

# 1 2 3 4 5 6 7 A 8 9 8 10 BB 11 C 12 CC D E 13 F FF 14 G 15 H HH 16 17 J 18 K 19 L LL M MM N P

D + 0.03 #0.00

d #0.13

6.35 7.26 8.38 13.21 13.34 13.34 14.22 15.88 18.36 19.05 20.57 22.23 22.23 25.40 23.80 25.40 26.92 28.58 31.75 33.27 34.93 38.61 36.58 38.10 41.40 42.80 42.80 44.45 47.75 52.38 57.15 58.60 63.50 69.85 70.36 73.03 77.72 79.50 90.17

3.05 4.12 5.21 6.86 6.99 8.31 8.64 10.37 11.26 11.69 13.74 14.86 15.83 16.51 17.28 18.16 19.69 21.54 23.49 24.26 27.05 27.82 29.33 30.81 32.64 33.89 33.89 35.94 38.96 42.93 45.34 48.44 51.69 54.89 58.04 60.58 64.39 66.68 76.08

4.09/4.16 5.26 6.35 8 9.53 9.53 10.04 11.84 12.45 13.08 15.21 16.39 17.30 18.75 18.75 19.69 21.21 23.04 24.97 26.04 28.53 30.61 30.86 32.39 35.69 36.88 36.88 38.99 42.04 45.93 48.39 51.39 54.74 58.30 61.09 63.63 67.44 69.98 79.38

1.22 +0.15 -0.00

2.03 +0.15 -0.00

2.34 +0.26 -0.00

3.25 3.25 2.34 3.25

R #0.13 0.54 0.57 0.57 0.57 1.27 0.56 0.70 0.73 0.60 0.70 0.73 0.76 0.73 1.12 0.73 0.76 0.76 0.73 0.74 0.89 0.74 1.40 0.76 0.74 1.52 1.50 1.50 1.52 1.54 1.50 1.52 1.47 1.52 1.70 1.52 1.52 1.52 1.65 1.65

RADIAL GAP G + 0.07 INCH BSP 0.2/0.38 0.13 0.26 0.26 0.26 0.32 0.19 0.35 0.25/0.51 0.42 0.55 0.29 0.52 0.29 0.29 0.30 0.32 0.31 0.35 0.32 0.45 0.29 0.63 0.29 0.23 0.82 0.30 0.41 0.38 0.33 0.30 0.45 0.28 0.40 0.28 0.40 0.51 0.43 0.82 0.51 0.45 0.40 0.32 0.45 0.45 0.57 0.45 0.48 0.45 0.59 0.45

Note: *** size reference fourth, fifth, sixth digits. Previous mark numbers for PP45 (industrial) and ACIS 11AG are shown by symbol #. Burst pressures were calculated using 549MN/m2 (130 ton f/in") UTS steel.

MINIMUM BURST PRESSURE BAR 2150 1570 1360 2430 1680 1680 1750 1480 1950 1890 1540 1560 1290 1560 1230 1310 1230 1120 1240 1275 1050 1210 880 860 775 780 780 680 660 690 870 690 780 950 740 720 750 670 680

SELF-CENTRING BSP RANGE BSP THREAD SIZE DIAMETER M

SIZE REFERENCE D

d #O.13

1/4 1/4 3/8 1/2 3/8 3/4 7/8 1 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/2

820 821 823 825 826 827 829 830 832 833 834 836 838 839

10.37 13.74 17.28 21.54 23.49 27.05 30.81 33.89 42.93 48.44 54.89 60.58 66.68 76.08

11.84 15.21 18.75 23.01 24.97 28.53 32.29 36.88 45.93 51.39 58.30 63.63 69.98 79.38

15.88 20.57 23.80 28.58 31.75 34.93 38.10 42.80 52.28 58.60 69.85 73.03 79.50 90.17

Burst pressures as per original BSP size.

2.03 2.34 0.25/0.51

3.25

8.26 11.18 14.67 18.24 20.27 23.83 27.51 29.92 38.45 44.45 50.42 56.26 62.36 71.50

0.38/0.63

0.20

+0.25 -0.00

-0.37 -0.00

GERMAN METRIC RANGE THREAD SIZE DIA. M

SIZE D REFERENCE +0.13 -0.00

d #O.10

d1 #0.10

3.5 4 5 5 5.5 6* 6 6 6.5 6.7 8 8 8* 8 8.5 10 10* 10 11 11* 11

201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 217 219 220 221

4.1 4.5 5.7 5.7 6.2 6.7 6.7 6.7 7.1 7.3 8.5 8.7 8.7 8.7 9.3 10.35 10.7 10.7 11.4 11.8 11.8

5.2 5.4 6.8 7.4 7.2 8.0 8.2 8.2 8.8 8.6 9.4 10.0 10.4 10.4 10.5 12.0 12.4 12.4 12.7 13.7 13.5

7.2 7.0 9.0 10.0 9.2 10.0 11.0 11.0 12.0 10.2 13.4 13.0 14.0 16.0 13.3 16.0 16.0 18.0 16.3 18.5 19.1

1.0#0.1

2.5#0.1

1.0#0.1

2.0#0.1 1.5#0.1

Burst pressures were calculated using 540MN/m2 (35 ton f/in") UTS steel. *Preferred styles where options are present.

R #0.1 0.55 0.45 0.65 0.85 0.5 0.65 0.75 0.75 0.85 0.65 0.45 0.65 0.85 0.85 0.60 0.82 0.85 0.85 0.65 0.95 0.85

P +0.25 -0.00

0.30

0.40

RADIAL GAP G #0.05 0.30 0.25 0.35 0.35 0.35 0.35 0.35 0.35 0.30 0.30 0.25 0.35 0.35 0.35 0.40 0.17 0.35 0.35 0.20 0.40 0.40

MINIMUM BURST PRESSURE BAR 1600 1270 1400 1510 1220 1120 1480 1480 1560 850 1780 1330 1510 2150 1200 1470 1300 1880 1280 1540 1760

GERMAN METRIC RANGE THREAD SIZE DIA. M

SIZE D REFERENCE +0.13 -0.00

d #0.10

d1 #0.10

12* 12 13* 13 13.5 14 15 16 17 17.5 18 20 21 22 22* 22 24 27 30 33* 33 36 39 42 48 51 52 60 68 75 88 125

222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 240 242 243 244 245 246 247 248 249 250 251 252 253 254 255

12.7 12.7 13.7 13.7 14.0 14.7 16.0 16.7 17.4 18.0 18.7 20.7 21.5 22.5 22.7 22.7 24.7 27.2 31.0 33.7 34.3 36.7 40.0 42.7 48.7 52.0 53.3 60.7 68.6 76.08 89.09 127.0

14.4 14.4 15.4 15.4 15.7 16.4 17.78 18.4 19.2 20.1 20.4 22.5 23.3 24.2 24.4 24.4 26.4 29.0 33.0 35.8 36.4 38.8 41.9 44.4 50.8 54.1 56.4 63.0 72.1 79.1 92.1 132.7

18.0 20.0 20.0 22.0 18.7 22.0 22.7 24.0 24.0 24.7 26.0 28.0 28.7 28.0 30.0 30.0 32.0 36.0 39.0 42.0 43.0 46.0 51.0 53.0 59.0 60.0 64.5 73.0 79.5 90.3 101.48 143.67

*Preferred size where options are present. .

1.5#0.1

2.5#0.15 1.5#0.1 2.0#0.1 3.0#0.1 2.0#0.1

2.5#0.1

R #0.1 0.85 0.85 0.85 0.85 0.85 0.85 0.89 0.85 0.90 1.05 0.85 0.90 0.90 0.85 0.85 0.85 0.90 1.0 1.05 1.05 1.05 0.95 0.85 1.05

3.0#0.15 3.5#0.15 3.38#0.15 3.25#0.15 5.0#0.15

P +0.25 -0.00

1.15 1.75 1.51 1.50

0.40

RADIAL GAP G #0.05 0.35 0.35 0.35 0.35 0.25 0.35 0.50 0.35 0.20 0.25 0.35 0.35 0.25 0.25 0.35 0.35 0.35 0.10 0.50 0.35 0.65 0.35 0.50 0.35 0.35 0.50 0.65 0.35 0.30 0.54 0.54 1.0

MINIMUM BURST PRESSURE BAR 1150 1680 1340 1810 900 1510 1260 1370 1150 1070 1260 1140 1080 760 1080 1080 1000 1130 870 840 870 890 1030 930 790 540 710 780 510 700 510 420

FRENCH METRIC RANGE THREAD SIZE DIA. M

SIZE D REFERENCE +0.13 -0.00

d #0.10

d1 #0.10

3 4 5 6 6 6 8 10 11 12 13 14 16 16.5 17 18 20 21 22 23 24 26 27 28 28.5 30 33 36 39 42 45 48

301 302 303 304 305 306 307 310 312 313 315 316 317 319 318 320 321 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337

3.6 4.6 5.6 6.6 6.85 7 8.6 10.7 11.8 12.7 13.8 14.7 16.7 17.2 17.4 18.7 20.7 21.7 22.7 23.7 24.7 27 27.7 28.6 29.2 30.7 33.7 37 40 40 46 49

5 6 7 8 8 8.4 10 12.1 13.2 14.1 15.2 16.1 18.1 18.7 18.8 20.4 22.4 23.4 24.4 25.4 26.4 28.7 29.4 30.3 30.9 32.4 35.4 39.6 42.6 45.6 48.6 51.6

7.5 9 10 11 13.27 11.4 13 17 18.1 19 20.1 21 23 23.9 23.7 27 29 30 31 32 33 35.3 36 36 37.5 39 42 48 51 54 57 60

1.0#0.1 1.3#0.1 1.0#0.1

1.5#0.1 2.1#0.1 1.5#0.1

2.0#0.1

2.5#0.1

Burst pressures were calculated using 540MNm2 (35 ton f/in2) UTS steel. .

R #0.1 0.7 0.7 0.7 0.7 0.57 0.7 0.7 0.7 0.65 0.7 0.7 0.7 0.7 0.75 0.7 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 1.3 1.3 1.3 1.3 1.3

P +0.25 -0.00

0.30

0.40

RADIAL GAP G #0.05 0.3 0.3 0.3 0.3 0.42 0.5 0.3 0.35 0.4 0.4 0.4 0.35 0.35 0.35 0.2 0.35 0.35 0.35 0.35 0.35 0.35 0.5 0.35 0.3 0.35 0.35 0.35 0.5 0.5 0.5 0.5 0.5

MINIMUM BURST PRESSURE BAR 1980 2000 1780 1680 1970 1540 1330 1730 1610 1530 1430 1370 1240 1020 1130 1450 1340 1290 1240 965 1160 860 1060 730 810 970 900 1010 950 890 860 790

BONDED SEALS TO SUIT PIPE CONNECTIONS AND COUPLINGS AS RECOMMENDED IN ISO1179 - 1973 (FORMERLY A CETOP RECOMMENDATION) INSTALLATION DATA Series C 1. IRREGULAR, ADHERING FLASH PERMISSABLE 0.38mm WIDE MAXIMUM (0.015in) 2. 0.13mm MAXIMUM RADIUS (0.005in) THE JOINT SURFACE IS TO BE FLAT AND SQUARE TO THE AXIS OF THE THREAD. 3. CONCENTRICITY TOLERANCE 0.25mm (0.010in) DIAMETER MAXIMUM DATUM THREAD DIAMETER. 4. THE DIAMETER OF CHAMFER OR COUNTERBORE FOR REMOVAL OF FIRST THREAD MUST BE CONCENTRIC WITH AND NOT EXCEED THE THREAD DIAMETER. BONDED SEAL THREAD DIA. M SIZE BSP REF ***

D -0.2

d +0.2

d1 +0.2

1/16 1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2

12.7 14.7 18.7 22.7 26.7 32.5 39.5 49.5 55.5 68.5

8.3 10.4 13.85 17.35 21.65 27.3 34.2 42.8 48.7 60.5

9.9 12 15.75 19.25 23.55 29.2 36.1 44.7 50.6 62.4

519 510 511 512 513 514 515 516 517 518

S #0.15

1.25

R #0.2 0.8 0.8 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95

P +0.25 -0.00

0.25

Part number example 400-510-4490-41 Explanation of this i.e. 400-510-4490-91 is 1/8" bonded seal nitrate and zinc plated steel. Burst pressures were calculated using 540 MN/m2 (35 ton f/in2) UTS steel. .

D2 +0.5

A A1 max A2 min

C +0.4

MINIMUM BURST PRESSURE BAR

12 14 18 22 26 32 39 49 55 68

1 1 1.5 2 2.5 2.5 2.5 2.5 2.5 3

13 15 19 23 27 33 40 50 56 69

1100 930 793 775 586 500 414 500 434 448