Step 1: To attach to bed frame

Let’s get this thing fired up! First, slide two of the Horizontal Stretchers (E) into the Center Frame (B). Then slide the Right Side Frame (A) onto the ends of the Horizontal Stretchers (E). Once in place, secure using eight of the M6*20mm Bolts (1) and tighten using the provided Allen Key (6).

Then, repeat this process by sliding the remaining Horizontal Stretchers (E) and (F) onto the ends of the Center Frame (B). Next, slide the Left Side Frame (C) onto the ends of the Horizontal Stretchers (E) and (F). Once in place, secure using eight of the M6*20mm Bolts (1) and tighten using the provided Allen Key (6).

These assembly steps are for attaching the headboard to your existing bed frame. If you’d rather mount the headboard to your wall, skip ahead to page 13.

Step 2

Next, slide the Legs (D) into the bottom of the frame you built in Step 1. Secure by placing a Flat Washer (4) first, then a Spring Washer (3) on top of that, and finally a M6*20mm Bolt (1). Tighten using the provided Allen Key (6).

Step 3

Now it’s time to attach the Bed Frame Adapter Plates (G) to the Legs (D).

To secure these together, run the M6*55mm Bolts (2) through the back of the Legs (D) and in through the Bed Frame Adapter Plates (G).

Be sure you’ve placed the Flat Washer (4) and Spring Washer (3) before inserting the Bolt (2).

Then, secure on the other side using the M6*7mm Nuts (5). Again, make sure you place the Flat Washer and Spring Washer before securing the Nuts.

Tighten all to 75%.

Note: The slotted cutouts on the headboard legs and bed frame adapter plates allow for adjustability to be compatible with a variety of different bed frames.

Bed Frame Adapter Plate Notes: Adapter Plates can be used in 2 different orientations (shown to the right) to allow for maximum height adjustability. Slotted holes also allow for maximum compatibility with your bed frame.

Now it’s time to attach the headboard to your bed frame (not included). To secure the headboard, align the holes in your bed frame with the slotted holes in the Bed Frame Adapter Plates (G). Once aligned, slide the M6*20mm Bolts (1) into place.

Be sure to first place a Flat Washer (4), then a Spring Washer (3) before inserting the bolts.

Secure on the other side using the M6*7mm Nuts (5). Again, be sure to first place a Flat Washer and then a Spring Washer before inserting the Nuts.

Tighten all to 100%.

Lay the Upholstered Panel (H) over the top of the metal frame you’ve assembled.

With the strap buckles at the top, tighten the middle strap.

Step 6

Now, using the M6*20mm Bolts (1), secure the Upholstered Panel (H) to the Horizontal Stretcher (F). This will help keep everything in place before you tighten the rest of the straps.

Step 7

Finally, go ahead and begin to tighten all of the straps.

Helpful tip: Slowly tighten the straps in equal increments to one another for the best results; to have everything tightened equally and in alignment.

You did it! Now all that’s left to do is sit back, relax, and enjoy your new headboard!

Step 1: To mount on wall

Let’s get this thing fired up! First, slide two of the Horizontal Stretchers (E) into the Center Frame (B). Then slide the Right Side Frame (A) onto the ends of the Horizontal Stretchers (E). Once in place, secure using eight of the M6*20mm Bolts (1) and tighten using the provided Allen Key (6).

Then, repeat this process by sliding the remaining Horizontal Stretchers (E) and (F) onto the ends of the Center Frame (B). Next, slide the Left Side Frame (C) onto the ends of the Horizontal Stretchers (E) and (F). Once in place, secure using eight of the M6*20mm Bolts (1) and tighten using the provided Allen Key (6).

These assembly steps are for mounting the headboard to your wall. If you’d rather attach the headboard to your existing bed frame, head back to page 6.

Step 2

Lay the assembled metal frame over the Upholstered Panel (H).

Be sure that the hardware is facing out.

With the strap buckles at the top, tighten the middle strap.

Step 4

Next, using the M6*20mm Bolts (1), secure the Upholstered Panel (H) to the Horizontal Stretcher (F). This will help keep everything in place before you tighten the rest of the straps.

Step 5

Finally, go ahead and begin to tighten all of the straps. Helpful tip: Slowly tighten the straps in equal increments to one another for the best results; to have everything tightened equally and in alignment.